LM339DG - Quad Open-Collector Comparator | onsemi
MPN: LM339DG ✓ چالاکLM339DG گشتی
A quad comparator is an integrated circuit containing four comparison channels on one package. Each channel compares a non-inverting input with an inverting input and produces a logic-level indication of their relationship. Comparators occupy the analog comparator category within interface and signal-conditioning semiconductors. Unlike a precision operational amplifier, a comparator is optimized for fast output transitions and level detection rather than accurate closed-loop amplification.
The LM339DG supports the voltage range required by industrial, automotive, and consumer systems. Its low supply-current drain is specified as 0.8 mA typical, and its low input bias current helps reduce errors in high-impedance sensing circuits. The open-collector output architecture permits wired-OR connections, external pull-up resistor selection, and level translation to the logic voltage used by the surrounding system. Outputs require a pull-up resistor because the output transistors do source current.
The manufacturer positions the LM339 family for level detection, low-level sensing, memory applications, consumer equipment, automotive electronics, and industrial electronics. Four channels in one 14-pin SOIC can reduce board area when a system compares multiple thresholds, monitors several sensor lines, or implements window detection. Independent inputs allow each channel to establish a separate reference or limit.
Circuit design must account for open-collector outputs, input common-mode limits, output pull-up requirements, and unused input states. Pull-ups should use the receiving logic's supply voltage when level translation is required, while their resistance should balance rise time, power consumption, and output-current capability. Unused comparator inputs must be tied to defined reference potentials rather than left floating.
The LM339DG is appropriate when one package must provide multiple inexpensive threshold decisions across a wide supply range. It is less suitable when a push-pull output is required without external pull-ups, when input signals exceed the common-mode range, or when the application requires the low offset and noise performance of a dedicated precision comparator. This page combines device specifications, package guidance, replacement analysis, and practical design considerations for faster engineering selection.
جێگرەوەکانی جێگۆڕکێ بۆ LM339DG — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM339DG (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Comparator Type, Logic Compatibility, Package, Output Type, Operating Temperature Range.
LM239DG
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM339ADG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM339ADRG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM339M
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM339DR
✅ جێگرەوەی ڕاستەوخۆ✓ بەردەستە
$0.0738 / یەکە
بینینی داتاشیت →LM339DG زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | 4-channel general-purpose analog comparator |
| Number of Channels | 4 channels |
| Single-Supply Operating Voltage Range | 3 V to 36 V |
| Typical Input Bias Current | 25 nA |
| Typical Input Offset Current | 5 nA |
| Typical Supply-Current Drain | 0.8 mA |
| جۆری دەرچوون | Open collector |
| Logic Compatibility | CMOS, TTL, and MOS |
| Number of Inputs | 8 inputs |
| ژمارەی دەرچووەکان | 4 outputs |
| پاکێج | 14-pin SOIC |
| جۆری دامەزراندن | Surface mount |
| Supply Configuration | Single supply or dual supply |
| Primary Application | Level detection |
| Additional Applications | Low-level sensing and memory applications |
ڕێنمایی ڕێکخستنی پینی LM339DG 14-pin soic
ڕێکخستنی پین بۆ LM339DG (پاکێجی 14-pin soic). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM339DG.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM339DG گونجاوە بۆ 6 بەکارھێنانs: Industrial Threshold Detection, Automotive Sensor and Warning Logic, Consumer Equipment Level Monitoring, Memory and Supply Sequencing Logic, Low-Level Sensing, LED and Relay Status Control.
Industrial Threshold Detection
The LM339DG fits industrial threshold detection because four comparison channels operate from a 3 V to 36 V single supply and provide open-collector outputs that can drive CMOS or TTL logic through pull-up resistors. A controller can compare four sensor or process signals against separate references without allocating four single comparator packages. Typical input bias current of 25 nA is useful when the sensing network has high source impedance, while the 0.8 mA typical supply-current drain supports low-power control boards. Use one channel per limit, keep inputs inside the common-mode range, and select pull-up values that satisfy the receiving logic’s rise-time requirements.
پێشنیارکراو
Automotive Sensor and Warning Logic
The LM339DG can support automotive sensor monitoring and warning functions because its four channels and 3 V to 36 V operating range suit threshold decisions across vehicle electrical systems. Open-collector outputs permit wired-OR warning signals and flexible pull-up selection for the logic device receiving the indication. The low 25 nA typical input bias current reduces loading from high-impedance sensor interfaces, while the 0.8 mA typical supply-current drain limits continuous overhead. Confirm the exact ordering variant’s temperature grade and AEC-Q100 status, protect transient-prone inputs, and ensure every input and output remains within the datasheet limits for the vehicle environment.
پێشنیارکراو
Consumer Equipment Level Monitoring
The LM339DG is suitable for consumer equipment level monitoring when several rails, buttons, or indicators must be compared against reference voltages. Four channels in one 14-pin SOIC reduce component count and simplify routing, while the open-collector outputs can be pulled up to the logic supply used by a microcontroller or display controller. Its 25 nA typical input bias current is beneficial for resistive divider sensing, and the 0.8 mA typical supply-current drain supports efficient monitoring. Use defined reference levels, stable divider resistors, and suitable debounce or hysteresis components where the sensed signals change slowly or contain mechanical noise.
پێشنیارکراو
Memory and Supply Sequencing Logic
The LM339DG can implement memory and supply sequencing decisions by comparing rail voltages or control signals with programmed thresholds. Its four independent channels allow multiple detection points to be evaluated, and the open-collector outputs can combine events through pull-up resistors and wired-OR logic. Operation from 3 V to 36 V covers a broad range of system rails, while typical input bias current of 25 nA minimizes disturbance to high-impedance threshold networks. Designers should verify startup behavior, input common-mode limits, and output pull-up voltage, and should prevent unused channels from floating at a level that can cause unstable switching.
پێشنیارکراو
Low-Level Sensing
The LM339DG fits low-level sensing applications that require detecting small voltage differences around a reference. The manufacturer identifies low-level sensing as an intended application, and the typical 25 nA input bias current and 5 nA input offset current help preserve weak signals from resistive sensors. Open-collector outputs make threshold events easy to interface with low-power digital logic using a suitable pull-up. Use low-noise, stable reference components and account for input offset when setting trip points. Verify the minimum differential voltage, input bias behavior, and output timing at the selected supply voltage before setting production thresholds.
پێشنیارکراو
LED and Relay Status Control
The LM339DG can form the decision stage for LED indicators, relay drivers, and simple alarm outputs. Each open-collector output can sink the current for an indicator or driver stage while the pull-up resistor establishes the active-high logic level, allowing several events to be combined in a wired-OR arrangement. Four channels minimize package count when monitoring multiple system conditions. The 3 V to 36 V supply range supports varied control rails, but relay coils and LED strings require appropriate external transistors or driver circuits rather than direct overloading of a comparator output. Select pull-ups for the required transition speed and confirm output-current limits during fault conditions.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM339DG — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM239DG | LM339ADG4 | LM339ADRG4 | LM339M | LM339 |
|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Comparator Channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
جیاکەرەوە سەرەکییەکان
- Four comparator channels in one 14-pin SOIC (بەراورد بەTLV2402ID)
- Wide single-supply operating range (بەراورد بەLM2904P3)
- Low typical input bias current for threshold sensing (بەراورد بەLM239DG)
تێبینییەکانی دیزاین
Every open-collector output requires an external pull-up resistor. Without one, the output cannot actively reach a valid high level. Choose the pull-up supply to match the receiving logic family, and size the resistance using the allowable output sink current, required rise time, and switching frequency. A smaller resistor produces a faster edge but increases current when the transistor is on; a larger resistor reduces loading but can slow the logic transition.
Place the pull-up resistor close to the receiving input rather than far from the comparator. This minimizes the high-impedance trace length and reduces susceptibility to capacitive coupling, especially when several open-collector outputs are wired together. Keep sensitive comparator inputs away from the pull-up and output routing when possible, provide a low-impedance ground return, and avoid routing high-current switching paths beneath the analog input nodes.
Do not allow unused LM339DG channels to float. Tie each unused input to a defined potential within the input common-mode range so the output remains in a predictable state. Also check the output state during power-up and shutdown. The open-collector transistor can hold the output low during reset, which may create a false event unless the receiving logic includes an appropriate pull-up and reset-handling circuit.
When comparing slowly changing signals, add controlled hysteresis or positive feedback to prevent output chatter around the threshold. The amount of hysteresis should be derived from resistor noise, reference accuracy, and the required trip-point separation. For fast signals, use short input traces, a compact ground plane, and appropriate impedance control. The onsemi datasheet should be consulted for input common-mode limits, differential-input limits, and response-time conditions.
زانیاری پابەندبوون
The LM339 family is described for automotive, consumer, and industrial applications, but the exact LM339DG orderable variant’s compliance and qualification status must be confirmed from its current manufacturer documentation.