LM339N/NOPB - 4-Channel Low-Offset Comparator | Texas Instruments
MPN: LM339N/NOPB ✓ چالاکLM339N/NOPB گشتی
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a digital-level indication of their relationship. The LM339 family belongs to the comparator IC hierarchy, combining analog signal evaluation with logic-compatible output signaling. Its four independent channels allow one package to monitor multiple thresholds, detect window crossings, or perform four independent zero-crossing comparisons.
Key features include four independent comparator sections, a maximum offset voltage of 2 mV for all four comparators, and open-collector outputs that can sink output current for wired logic or pulled-up systems. The low-power architecture supports single-supply operation, while split power supplies are also possible. The 14-pin through-hole DIP package provides generous spacing and straightforward prototyping compared with a surface-mount footprint.
The open-collector output stage is the defining electrical feature of this comparator family. Each output can pull a logic rail low, but it does not actively source current. A pull-up resistor is therefore required when the output must reach a valid high level. This arrangement permits level translation, wired-AND behavior, and flexible output rise-time control, but system designers must account for pull-up resistance, load capacitance, output rise time, and propagation delay.
Typical applications include industrial sensor thresholds, battery and power-supply monitoring, overvoltage and undervoltage detection, zero-crossing detection, window comparators, control-system interlocks, and general-purpose logic interfaces. Because all four channels are independent, the device can reduce component count in multi-channel monitoring designs where board space and through-hole assembly are priorities.
For reliable operation, connect an output pull-up resistor to the voltage used by the receiving logic, keep input and output traces away from high-current switching paths, and observe the device's supply-voltage and input-common-mode limits. Decoupling near the supply pins helps reduce local noise, while the open-collector outputs should not be used as push-pull logic outputs without the appropriate pull-up network.
This page combines the LM339N/NOPB technical description, package information, comparison criteria, drop-in alternatives, and practical circuit-design guidance to help engineers evaluate the part for threshold, monitoring, and signal-conditioning applications.
جێگرەوەکانی جێگۆڕکێ بۆ LM339N/NOPB — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM339N/NOPB (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Comparator Type, Output Type, Supply Configuration, Mounting Type, Logic Compatibility.
LM339NG
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2901NG
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LP339N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2901N
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM3302N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM339N/NOPB زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Channel Count | 4 channels |
| Input Offset Voltage | 2 mV maximum for all four comparators |
| جۆری دەرچوون | Open-collector |
| Comparator Type | Low-power, low-offset differential voltage comparator |
| Supply Configuration | Single supply or split supply |
| Channel Independence | 4 independent comparator channels |
| Package Type | 14-pin DIP |
| شێوازی دامەزراندن | Through-hole |
| Output Pull-Up Requirement | External pull-up resistor required for a valid high output level |
ڕێنمایی ڕێکخستنی پینی LM339N/NOPB 14-pin dip
ڕێکخستنی پین بۆ LM339N/NOPB (پاکێجی 14-pin dip). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM339N/NOPB.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM339N/NOPB گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Threshold Detection, Power-Supply Overvoltage Monitoring, Battery Voltage Window Detection, Zero-Crossing Detection, Control-System Interlocks, Audio and Communication Level Interfaces.
Industrial Sensor Threshold Detection
The LM339N/NOPB is appropriate for industrial sensor interfaces that require several independent voltage thresholds. Its four independent comparator channels can evaluate signals from temperature, pressure, level, or process-control sensors without requiring four separate IC packages. The TI LMx39-N family documentation specifies offset voltage as low as 2 mV maximum for all four comparators, which supports decisions between closely spaced sensor-derived voltages. Each open-collector output can feed a controller input through a pull-up resistor to the controller's logic voltage. In an industrial installation, protect sensor inputs and supply rails from transients, maintain the input voltages within the common-mode range, and keep comparator traces away from motors and switching power stages.
پێشنیارکراو
Power-Supply Overvoltage Monitoring
The LM339N/NOPB can monitor a power rail by comparing a divided feedback voltage with a reference level. Four independent channels allow monitoring of multiple supply rails or different threshold points without duplicating comparator circuitry. Its low-power architecture supports single-supply operation over a wide voltage range, while the open-collector outputs can assert a fault signal by pulling a supervisor, relay-driver, or system-controller input low. Use a pull-up resistor tied to the appropriate logic rail and add filtering where the monitored signal may contain switching ripple. For an accurate protection design, include resistor tolerance, input offset voltage, supply tolerance, and the comparator's propagation behavior in the threshold-error budget.
پێشنیارکراو
Battery Voltage Window Detection
A battery-backed system can use two LM339N/NOPB channels to establish upper and lower voltage limits, with the remaining channels available for additional battery conditions or subsystem thresholds. The device's four independent channels are useful because undervoltage and overvoltage decisions usually require separate reference comparisons and dedicated outputs. The 2 mV maximum input offset specification in the TI LMx39-N documentation helps preserve separation between the two switching limits after signal conditioning. Open-collector outputs can be pulled up to a low-energy logic rail, and wired logic can combine fault indications. Account for battery chemistry, resistor-divider scaling, temperature drift, and input filtering so that transient load currents do not create false protection events.
پێشنیارکراو
Zero-Crossing Detection
The LM339N/NOPB can detect the crossing point of an analog waveform by comparing the signal against a reference voltage. Its independent comparator channels allow zero-crossing detection for more than one phase or polarity within the same package. The open-collector output provides a flexible pull-up arrangement and can drive a digital input when the source impedance and switching requirements are suitable. For sinusoidal AC signals, use an input network that limits current and protects the inputs, and account for comparator propagation delay when timing is important. The 14-pin DIP package is especially convenient for prototypes and educational equipment where a through-hole footprint simplifies socketed assembly and waveform experimentation.
پێشنیارکراو
Control-System Interlocks
The LM339N/NOPB is useful for safety and sequencing interlocks that compare a command signal with a feedback or limit signal. Four independent channels can monitor separate machine states, and the open-collector outputs can pull a wired interlock line low when a limit is exceeded. This arrangement supports industrial control logic without requiring an active push-pull driver in every channel. Place the pull-up resistor on the interlock rail and design the output node so that one comparator can sink the required current. Validate the common-mode range, supply behavior, and propagation delay under actual noise conditions. For machinery applications, determine whether the overall safety function requires automotive qualification, reinforced isolation, redundancy, or a formally certified safety component.
پێشنیارکراو
Audio and Communication Level Interfaces
The LM339N/NOPB can serve as a simple level or threshold interface between analog communication circuitry and digital logic. Its low-offset comparator architecture is useful when the input signals are already conditioned into a narrow voltage band and the goal is to identify an upper or lower limit rather than reproduce an analog waveform. The open-collector output allows the interface to use the receiving system's logic voltage as the pull-up rail. This is advantageous in mixed-voltage equipment because the output can be referenced to a different supply than the comparator's input circuitry. Keep the output pull-up close to the receiving input, observe output-current limits, and use hysteresis when noise near the threshold could otherwise cause repeated output transitions.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM339N/NOPB — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM339NG | LM2901NG | LP339N | LM2901N | LM3302N |
|---|---|---|---|---|---|---|
| Package | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP | 14-PDIP |
| Brand | Texas Instruments | onsemi | onsemi | Texas Instruments | onsemi | onsemi |
| Comparator Channel Count | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels | 4 channels |
| Special Feature | Four independent comparators | Four independent comparators | Four independent comparators | Four independent comparators | Four independent comparators | Four independent comparators |
جیاکەرەوە سەرەکییەکان
- Four independent threshold channels in one DIP package (بەراورد بەLM339NG)
- 2 mV maximum offset specification applies to all four comparators (بەراورد بەLM2901NG)
- Single- and split-supply operating architecture (بەراورد بەLM3302N)
- Same 14-DIP footprint as the principal cross-brand substitutes (بەراورد بەLM2901N)
تێبینییەکانی دیزاین
Do not treat the open-collector output as a push-pull logic driver. Pull the output up to the voltage expected by the receiving logic, confirm that the comparator can sink the resulting current, and check that the pull-up value produces an acceptable rise time with the total output capacitance. When several outputs are connected to one node, verify the total sink current and ensure that the wired node remains in a valid logic state during normal operation.
Place the supply bypass capacitor close to the device's supply pin and ground connection to minimize local supply ripple. Use a short return path to the source of the compared signals, because comparator decisions can change when input-reference or ground bounce exceeds the applied threshold difference. Evaluate the complete input-divider current because excessive divider resistance increases sensitivity to bias current, leakage, and board contamination.
Add positive feedback as hysteresis when the compared signal can cross the threshold slowly or with noise. The hysteresis loop must be smaller than the intended decision window but large enough to prevent output chatter. Keep comparator inputs and the output return path away from switch-node copper, inductors, and high-current motor wiring. If the input is derived from a resistive divider, account for amplifier or comparator input effects across the full operating-temperature range.
Use the TI LMx39-N package drawing and numbered pin-description table to assign the 14-pin PCB footprint. The through-hole DIP format offers generous component spacing, but long exposed leads can pick up noise or be damaged during assembly. Maintain suitable clearance around the package for insertion and soldering, and connect the ground pins according to the manufacturer guidance rather than assuming every ground connection is interchangeable for every operating condition.
زانیاری پابەندبوون
The manufacturer product page and datasheet link are available, but the accessed excerpts do not provide RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. The NOPB suffix identifies the standard Texas Instruments ordering option, but its package and environmental declarations should be confirmed from the current manufacturer product documentation.