LM393APWRG4 - 18V Dual Comparator | Texas Instruments
MPN: LM393APWRG4 ✗ کۆتایی ژیانLM393APWRG4 گشتی
A differential comparator is an analog comparator that evaluates two input voltages and changes its output state according to their relative polarity. The dual-channel implementation provides two comparators in one package, reducing component count and PCB area. In the broader semiconductor hierarchy, the LM393A belongs to the comparator class, within integrated circuits, interface ICs, and analog signal-conditioning devices.
The LM393APWRG4 provides a response time of 1.3 µs, a maximum input offset voltage of 4 mV, and a low input bias current magnitude of 0.4 µA. Its open-collector outputs allow the output voltage to be pulled to the logic supply used by the following device. The commercial-temperature product is supplied in the compact PW 8-TSSOP package.
Each internal channel compares its non-inverting and inverting inputs. When the non-inverting input is electrically higher than the inverting input, the associated output transistor turns on and pulls the open-collector node toward ground. When that condition reverses, the transistor turns off, allowing the pull-up resistor to raise the output. This behavior makes the output level adjustable through the external pull-up supply and resistor.
Typical uses include overvoltage and undervoltage detection, sensor-threshold switching, zero-cross detection, industrial control interfaces, and relay or lamp-driver logic. The two channels may operate independently, or they can be interconnected in oscillator, window-comparator, and Schmitt-trigger configurations. Open-collector outputs are particularly useful when multiple devices must share a common wired bus.
PCB design should reserve space for each channel's input compensation network, where applicable, and route comparator inputs away from switching nodes and high-current return paths. Place the output pull-up resistor close to the open-collector output to limit trace susceptibility to noise. The exposed thermal considerations are modest for ordinary comparator operation, but input and output current should remain within the ratings defined by the manufacturer datasheet.
This product page combines the exact device identity, lifecycle information, technical specifications, application guidance, and available family alternatives. It also identifies the package and pinout documentation needed for PCB review, sourcing continuity, and cross-reference decisions.
جێگرەوەکانی جێگۆڕکێ بۆ LM393APWRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LM393APWRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Input Bias Current, Input Offset Voltage, Number of Channels, Package, Response Time.
LM393BPWRG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM393PWRG4
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LM2903BPWRG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM2903APWRG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM293PWRG4
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
LM393APWRG4 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 18 V |
| جۆری دەرچوون | Open-collector |
| Input Offset Voltage | 4000 uV maximum |
| Response Time | 1300 ns |
| Input Bias Current | -0.4 uA |
| Temperature Grade | Commercial |
| پاکێج | 8-TSSOP (PW) |
| Terminal Count | 8 terminals |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی LM393APWRG4 rectangular
ڕێکخستنی پین بۆ LM393APWRG4 (پاکێجی rectangular). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LM393APWRG4.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LM393APWRG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Overvoltage Detection, Temperature Sensor Thresholding, Power Supply Sequencing, Motor and Relay Control, Battery Charger Protection, Digital Interface Level Detection.
Industrial Overvoltage Detection
LM393APWRG4 suits industrial overvoltage detection because one channel can compare a protected signal against a reference threshold while the second channel handles an undervoltage or watchdog condition. Its 1300 ns response time provides rapid transition detection, and the 4000 uV maximum input offset must be included in the threshold design. Each open-collector output can pull down a system-enable line through a pull-up resistor, providing a fail-safe signal path without an active push-pull output driver.
پێشنیارکراو
Temperature Sensor Thresholding
LM393APWRG4 can implement a local temperature-alarm threshold by comparing the output of a resistive sensor network against a precision reference. Two channels permit independent upper and lower thresholds, or one channel can monitor temperature while the other provides a fault signal. The input bias current of -0.4 uA limits loading on high-resistance sensor networks, while the 4000 uV maximum offset should be included when defining the alarm accuracy.
پێشنیارکراو
Power Supply Sequencing
LM393APWRG4 is useful in multi-rail power sequencing because its two differential channels can supervise separate supply thresholds. One open-collector output can discharge a delay or enable node, while the other can report a second rail's status. The 1300 ns response time supports prompt threshold transitions, and the dual-channel topology reduces the number of comparator packages needed. Pull-up voltage selection and output-current limits must match the logic rail connected to each output.
پێشنیارکراو
Motor and Relay Control
LM393APWRG4 can serve as a control interface between low-current sensing circuitry and a relay, solenoid, or motor-driver stage. A comparator channel converts a control-voltage threshold into an open-collector assertion that can operate a transistor or driver input. The 1.3 µs response time helps minimize actuation delay, while the two-channel arrangement can supervise both command and feedback conditions. External transistor selection and protection should account for the load current and flyback requirements.
پێشنیارکراو
Battery Charger Protection
LM393APWRG4 can monitor battery-cell or charger thresholds in a protection circuit by comparing each input against a reference voltage. The two independent channels allow separate charge and discharge limits, while the open-collector outputs can directly control a charger-disable signal or status input. Designers should account for the 4000 uV maximum input offset, verify the common-mode operating range, and select pull-up resistors that remain compatible with the logic rail and required output sink current.
پێشنیارکراو
Digital Interface Level Detection
LM393APWRG4 fits interface level detection where an analog signal must determine the state of a digital control line. Its differential inputs compare the incoming level against a threshold, and the open-collector output can provide wired-AND behavior or drive an enable input through a pull-up. The dual-channel implementation permits two independent logic checks in one 8-TSSOP package. Confirm input common-mode limits, output sink current, pull-up voltage, and response timing for the interface standard.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LM393APWRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LM393BPWRG4 | LM393PWRG4 | LM2903BPWRG4 | LM2903APWRG4 | LM293PWRG4 |
|---|---|---|---|---|---|---|
| Package | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) | 8-TSSOP (PW) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Maximum Supply Voltage | 18 V | 18 V | 18 V | 18 V | 18 V | 18 V |
جیاکەرەوە سەرەکییەکان
- Two independent comparator channels in one 8-pin TSSOP package (بەراورد بەLM393BPWRG4)
- Documented 1300 ns response time (بەراورد بەLM2903BPWRG4)
- Open-collector outputs support wired logic (بەراورد بەLM293PWRG4)
تێبینییەکانی دیزاین
Do not treat an open-collector output as a push-pull logic output. Fit a pull-up resistor on every output that must attain a high state, and select its resistance from the required sink current, rise-time target, logic-supply voltage, and leakage requirements. The manufacturer datasheet should be used to confirm output-current limits and the permitted output voltage range.
Place each pull-up resistor close to its associated open-collector output to minimize trace area and susceptibility to coupling. Keep comparator input traces away from power-switching nodes, inductors, and high-current return paths. Connect the ground reference directly to the device ground pin with a low-impedance route, because input thresholds are referenced to this node and ground noise can appear directly as comparator error.
Account for the 4000 uV maximum input offset when defining protection or control thresholds, especially when the monitored difference between two inputs is small. The -0.4 uA input bias current also matters for high-source-impedance sensor networks. Evaluate resistor tolerances, sensor loading, input protection leakage, and comparator propagation delay together to determine the usable threshold accuracy and response margin.
The 18 V maximum supply rating is an absolute device limit, not a recommended operating point. Include margin for supply tolerance, transients, and startup overshoot, especially in 12 V automotive or industrial systems. Decouple the supply pin locally with the capacitance and layout specified by the manufacturer datasheet, and avoid routing high-current return paths through the comparator ground connection.
زانیاری پابەندبوون
The manufacturer product page identifies LM393APWRG4 as commercial grade and no longer in production, but no explicit compliance declarations are present in the cited product information.