LT3469ETS8#TRMPBF - 33V Piezo Driver | Analog Devices
MPN: LT3469ETS8#TRMPBF ✓ چالاکLT3469ETS8#TRMPBF گشتی
A transconductance, or gm, amplifier converts a differential input-voltage signal into an output current. This differs from a conventional voltage-output amplifier because the LT3469 includes an internal switching regulator that boosts the amplifier supply. The result is a compact driver capable of operating high-voltage piezo elements without requiring a separate high-voltage boost stage. In the component hierarchy, the LT3469 belongs to the transconductance amplifier and piezo-driver families within power-management and signal-conditioning ICs.
Key features include a 33 V maximum driven output from a low-voltage supply, differential inputs, typical output-current limiting of ±40 mA, and compatibility with capacitive loads from 5 nF to 300 nF. The internal switching regulator produces the boosted voltage needed by the Class AB output stage. Because slew rate is limited by maximum output current, the available drive strength depends on the load capacitance, supply arrangement, and current-limit behavior.
The LT3469 combines a switched-capacitor or switching supply stage with an analog Class AB transconductance output. Its 35 V switching-regulator output capability provides headroom above the stated 33 V amplifier output limit. Differential input handling is useful when the actuator command is generated differentially or when unwanted common-mode voltage is present. The small TSOT-23-8 package supports compact instrument, actuator-control, and embedded equipment designs.
Typical applications include piezo speakers, ultrasonic transducers, haptic microactuators, optical-scanning actuators, and small high-voltage piezoelectric loads. The LT3469 is particularly useful when the available system supply is 5 V or 12 V but the actuator requires substantially greater drive voltage. The integrated boost function also reduces the number of external power-conversion blocks required compared with a discrete driver arrangement.
Designers should pay particular attention to the switching node because its sharp rise and fall edges can couple into nearby circuits. The manufacturer datasheet recommends surrounding the SW pin with metal connected to VCC on three sides, minimizing the area of traces connected to SW, and placing a ground plane beneath the switching regulator. Input, output, and compensation networks must also follow the application guidance in the LT3469 datasheet.
This page consolidates verified manufacturer and distributor information, practical switching-layout guidance, application context, pricing references, and a compatibility-focused assessment of available alternatives. It is intended to help engineers evaluate whether the LT3469ETS8#TRMPBF provides the required voltage, current, load capacitance, package, and layout characteristics before committing to a PCB design.
جێگرەوەکانی جێگۆڕکێ بۆ LT3469ETS8#TRMPBF — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ LT3469ETS8#TRMPBF (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Operating Temperature Range.
LT3469ETS8#TRPBF
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →LT3469ETS8#TRMPBF زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | Transconductance amplifier with integrated boost regulator |
| Manufacturer | Analog Devices |
| MPN | LT3469ETS8#TRMPBF |
| Amplifier Class | Class AB |
| Channel Count | 1 channel (mono) |
| Supply Voltage Range | 2.5 V to 16 V |
| Supported Supply Examples | 5 V or 12 V |
| Maximum Driven Output Voltage | 33 V |
| Internal Switching Regulator Capability | 35 V |
| Typical Amplifier Current Limit | ±40 mA |
| Supported Capacitive Load Range | 5 nF to 300 nF |
| Input Type | Differential |
| Slew Rate | Limited by maximum output current |
| پاکێج | TSOT-23-8 |
| جۆری دامەزراندن | Surface mount |
| Packaging | Tape and reel |
| مەودای پلەی گەرمیی کارکردن | -40°C to 85°C |
| Guaranteed Performance Temperature Range | 0°C to 85°C |
| دۆخی RoHS | Compliant |
| Product Category | Switching voltage regulator |
ڕێنمایی ڕێکخستنی پینی LT3469ETS8#TRMPBF tsot-23-8
ڕێکخستنی پین بۆ LT3469ETS8#TRMPBF (پاکێجی tsot-23-8). ئەم ئامێرە وزەییە تەرمیناڵی گەیت، درەین و سەرچاوەی ھەیە. بۆ پاکێجە ناڕێکخراوەکان، سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ئاراستەی وردی پینی 1 و زانیاری شوێنپێ. بەکارھێنانە باوەکان بریتین لە دیزاینی دابینکردنی وزە، بەکارخستنی مۆتۆر و گۆڕینی بار.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ LT3469ETS8#TRMPBF.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
LT3469ETS8#TRMPBF گونجاوە بۆ 6 بەکارھێنانs: Piezo Speaker Drive, Ultrasonic Transducer Excitation, Piezo Haptic Microactuator, Optical Scanner and Micropositioning Actuator, Precision Test and Measurement Actuator, Industrial Piezo Valve or Actuator Control.
Piezo Speaker Drive
The LT3469ETS8#TRMPBF is well suited to compact piezo-speaker drivers because it combines a differential Class AB transconductance stage with an internal boost regulator. A 5 V or 12 V system supply can generate output drive up to 33 V, avoiding a separate high-voltage boost circuit when board area is limited. Verified data supports capacitive loads from 5 nF to 300 nF, so the speaker’s effective capacitance must remain within that range. The ±40 mA typical current limit also provides a defined relationship between peak drive, load capacitance, and achievable slew rate. Designers should derive the required waveform amplitude and peak current before layout, then use a short output path and verify that switching-node energy does not enter the audio input or output.
پێشنیارکراو
Ultrasonic Transducer Excitation
Ultrasonic transducers frequently benefit from voltage drive well above the available logic supply, making the LT3469ETS8#TRMPBF a practical match for compact excitation circuitry. Its internal switching regulator boosts a 5 V or 12 V source sufficiently for the transconductance stage to deliver output up to 33 V. The differential input supports cleaner command capture when the drive waveform is generated as a small signal around a bias point. Because the verified load range is 5 nF to 300 nF and the typical amplifier current limit is ±40 mA, transducer capacitance and operating frequency determine whether peak current and slew rate are adequate. PCB validation should include loaded-output waveform measurements and checks for unwanted coupling from the SW node.
پێشنیارکراو
Piezo Haptic Microactuator
The LT3469ETS8#TRMPBF can provide the elevated drive required by small piezo haptic actuators while accepting a conventional 5 V or 12 V system supply. Its output capability reaches 33 V and its differential inputs simplify integration with low-voltage command circuitry. The integrated boost function is valuable in wearables, handheld instruments, and compact laboratory equipment where a separate high-voltage driver would consume additional board area. The design must remain within the 5 nF to 300 nF verified capacitive-load range and account for the ±40 mA typical current limit when estimating actuator drive. Mechanical resonance, dielectric stress, and heating should also be considered because the electrical waveform can affect long-term actuator reliability.
پێشنیارکراو
Optical Scanner and Micropositioning Actuator
Small optical-scanning or micropositioning mechanisms that use piezoelectric actuators benefit from the LT3469ETS8#TRMPBF’s combination of low-voltage supply operation and high-voltage drive. The internal boost regulator allows the circuit to produce output drive up to 33 V from a 5 V or 12 V source, while the differential Class AB amplifier provides a controlled current response to the command voltage. With verified support for 5 nF to 300 nF loads, compact mechanisms can often be driven without a discrete high-voltage supply stage. The key performance trade-off is that slew rate is limited by maximum output current, so high-frequency positioning commands may require lower load capacitance or a different driver. Layout should minimize actuator-loop area and preserve the manufacturer’s recommended SW-node shielding.
پێشنیارکراو
Precision Test and Measurement Actuator
The LT3469ETS8#TRMPBF is appropriate for test and measurement equipment that drives a piezoelectric load from a low-voltage system architecture. Its 2.5 V to 16 V supply range accommodates 5 V and 12 V instrumentation rails, and the integrated boost stage can support output drive up to 33 V without a separate converter. Differential command inputs are useful when the actuator controller generates a small differential signal and must reject common-mode variation. The typical ±40 mA current limit and 5 nF to 300 nF load range provide the initial boundaries for waveform planning. For accurate measurements, use a ground plane below the switching regulator, keep SW traces short and guarded by VCC metal, and verify that boost ripple does not contaminate the actuator command or measurement signal.
پێشنیارکراو
Industrial Piezo Valve or Actuator Control
The LT3469ETS8#TRMPBF can serve as the high-voltage drive element in compact industrial piezo-valve or actuator-control modules. Operating from a 5 V or 12 V supply while providing drive up to 33 V reduces the external power-conversion complexity of a distributed control node. The differential transconductance input can be driven from a low-level controller, and the mono Class AB output is suitable when each channel drives one actuator. Compatibility with 5 nF to 300 nF loads must be checked against the valve’s cable and mechanical capacitance, because added cable capacitance increases charge-transfer demand and reduces available slew rate. Robust production layouts should isolate the SW node, provide a continuous ground reference, and test startup behavior with the actuator connected.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ LT3469ETS8#TRMPBF — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | LT3469ETS8 |
|---|---|---|
| Package | TSOT-23-8 | TSOT-23-8 |
| Brand | Analog Devices | Analog Devices |
| Output Voltage | 33 V | 33 V |
| Output Current | 40 mA | 40 mA |
| RoHS | Compliant | Compliant |
جیاکەرەوە سەرەکییەکان
- Integrated high-voltage boost and differential transconductance output (بەراورد بەDiscrete piezo driver)
- Verified operating-load envelope (بەراورد بەLT3468ETS8#TRMPBF)
- Same-family ordering compatibility (بەراورد بەLT3469ETS8)
تێبینییەکانی دیزاین
Treat the SW node as a high-edge-rate signal. The manufacturer datasheet recommends surrounding SW with metal connected to VCC on three sides, minimizing the area of all SW-connected traces, and placing a ground plane beneath the switching regulator to reduce interplane coupling. Keep the switching loop compact and prevent the guarded SW region from extending beneath sensitive input or actuator nodes.
Calculate actuator charge demand before selecting the operating waveform. The verified capacitive-load range is 5 nF to 300 nF, while typical amplifier current limiting is ±40 mA and slew rate is limited by maximum output current. Cable capacitance must be included because it adds to the piezo load and can increase required peak current, particularly at higher excitation frequencies.
Do not interpret the 33 V output capability as permission to exceed the component’s absolute maximum ratings. Consult the official LT3469 datasheet for supply limits, output-voltage restrictions, current-limit behavior, compensation values, and operating-temperature details. Also verify the exact ordering suffix because LT3469ETS8 and LT3469ETS8#TRMPBF are related forms whose temperature-grade and packaging identifiers differ.
زانیاری پابەندبوون
RoHS compliance is reported by the verified cross-reference listing. The supplied data does not explicitly state REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to the stated commercial-grade LT3469 family unless a separately qualified automotive ordering code is selected.