MAX152EAP+ - 8-Bit 400ksps Half-Flash ADC | Maxim Integrated
MPN: MAX152EAP+ ✓ چالاکMAX152EAP+ گشتی
An ADC is a data converter IC that turns an analog voltage into a digital code. Within the semiconductor hierarchy it sits as an analog-to-digital converter inside the broader mixed-signal / data-converter family. The MAX152 belongs to the flash-converter subclass, which uses an array of parallel comparators and a resistive ladder to resolve an input voltage against a reference. The MAX152 uses a "half-flash" conversion technique, splitting the quantization into two half-resolution steps, which lowers power and die area compared with a full 8-bit flash converter while keeping conversion time short.
Key features of the MAX152EAP+ include the 400 ksps throughput rate, 8-bit resolution, single-ended unipolar or differential bipolar input capability, and a POWERDOWN pin that drops the typical supply current to 1 uA for battery-operated equipment. It accepts either a single +3 V or dual +/-3 V supply, so it fits both 3 V logic systems and bipolar analog front ends, and its microprocessor-compatible parallel output bus simplifies interfacing with older processor families.
Technically, the MAX152 combines a reference input path, an RDET resistive-ladder node, and a comparator array whose thresholds are switched in two successive passes. Because the second pass refines the coarse result of the first, effective resolution is 8 bits at 400 ksps, a strong figure for a device of this vintage and power class. The parallel DB0-DB7 outputs let the host processor latch the code directly on the write strobe, avoiding the serial overhead of successive-approximation converters.
Typical uses include industrial process monitoring, resistive sensor and digital potentiometer measurement, 4-20 mA loop instrumentation, power-supply telemetry, battery-operated portable instruments, and general low-speed data-acquisition front ends where a parallel bus and very low standby current matter more than resolution above 8 bits.
When designing around the MAX152, treat the analog input as a switched-capacitor sampling node: keep the source impedance low, place the reference bypass capacitor directly at the REF pins, and keep the analog trace short and away from the digital strobe lines to limit coupling of clock noise into the conversion result.
This page consolidates the manufacturer description, distributor availability and pricing structure, verified drop-in alternatives, and practical layout and signal-integrity guidance for engineers who need a fast, low-power 8-bit ADC in the legacy SSOP-20 footprint.
جێگرەوەکانی جێگۆڕکێ بۆ MAX152EAP+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX152EAP+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Conversion Time, Package, Power-Down Current.
MAX152CAP+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX152EAP
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX152EAP+T
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX152EAP+ زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| وردی | 8 bit |
| Conversion Architecture | Half-flash |
| Number of Analog Inputs | 1 |
| ڕێژەی نموونەگرتن | 400 ksps |
| Conversion Time | 1.8 us |
| Supply Voltage, Single | +3 V |
| Supply Voltage, Dual | +/-3 V |
| Power-Down Current | 1 uA typical |
| Input Signal Range | Unipolar or bipolar |
| Output Interface | Parallel microprocessor-compatible, 8-bit data bus |
| پاکێج | 20-pin SSOP |
| جۆری دامەزراندن | Surface Mount |
| Automotive Qualification (AEC-Q100) | Not applicable |
| Manufacturer | Maxim Integrated (Analog Devices) |
ڕێنمایی ڕێکخستنی پینی MAX152EAP+ 20-pin ssop
ڕێکخستنی پین بۆ MAX152EAP+ (پاکێجی 20-pin ssop). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX152EAP+.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX152EAP+ گونجاوە بۆ 6 بەکارھێنانs: Industrial Process Monitoring, Battery-Powered Portable Instrumentation, Digital Potentiometer and Resistive Sensor Readback, Power Supply and Rail Telemetry, General-Purpose Data Acquisition Front End, Smart Sensor and IoT Node.
Industrial Process Monitoring
The MAX152EAP+ suits single-loop industrial process monitoring where a 4-20 mA or 0-10 V input must be digitized close to the sensor. Its 400 ksps throughput and 1.8 us conversion time let the front end capture transients without a slow successive-approximation lag, while the 8-bit code maps to roughly 256 counts over the loop span, adequate for alarm and setpoint work. Operating from a single +3 V rail simplifies field-isolated module design, and the 1 uA power-down current limits standby drain in battery-backed transmitters. The parallel DB0-DB7 bus reads directly into a small microcontroller without level shifting.
پێشنیارکراو
Battery-Powered Portable Instrumentation
For handheld meters and portable test equipment, the MAX152EAP+ is attractive because the POWERDOWN pin cuts typical supply current to 1 uA, as stated in the Maxim MAX152 datasheet. A design can wake the converter, take one 1.8 us conversion, latch the parallel result and return to a microamp standby state between samples, which extends run time far beyond a continuously running converter. The 400 ksps rate also allows burst sampling of a waveform when the operator requests a reading. The 20-pin SSOP package keeps board area small in handheld enclosures.
پێشنیارکراو
Digital Potentiometer and Resistive Sensor Readback
Resistive sensors such as digital potentiometers, thermistors and strain bridges are slow enough that resolution, not throughput, dominates the design, yet the MAX152EAP+ still fits well. The half-flash architecture and 8-bit code provide a straightforward ratio-style measurement path, and the 1.8 us conversion time is short compared with the settling time of the resistive network itself. Because the input may be wired unipolar or bipolar, the same converter handles a ratiometric divider referenced to the supply and a bipolar bridge output. The parallel bus keeps the host microcontroller free for calibration and linearization routines.
پێشنیارکراو
Power Supply and Rail Telemetry
The MAX152EAP+ can be used as a supervisory and telemetry element in 3 V supply systems, converting a scaled rail voltage into a digital code for a supervisory controller. Because the device runs from a single +3 V supply, it can monitor a 3 V rail directly with minimal headroom loss, and the dual +/-3 V option supports ± supply rails in legacy analog systems. The 8-bit resolution corresponds to about 0.4% steps over a full-scale 3 V span, which is adequate for supply-rail event logging and fault records. The 400 ksps rate permits sampling during a transient if the design needs to capture droop events.
پێشنیارکراو
General-Purpose Data Acquisition Front End
The MAX152EAP+ remains a practical front end for educational, laboratory and low-cost data-acquisition boards because it needs only a few external passive components plus the reference bypass. The microprocessor-compatible parallel interface is a decisive advantage with classic 8-bit microcontrollers, since no serial framing code is required and the read cycle is a simple latch on the write strobe. Throughput of 400 ksps supports sampling several slow analogue channels through a multiplexer. The 20-pin SSOP package is a widely supported footprint, which simplifies assembly and makes the board easy to rework when a higher-resolution converter is preferred later.
پێشنیارکراو
Smart Sensor and IoT Node
In IoT sensor nodes that must stay compatible with an older microcontroller architecture, the MAX152EAP+ provides a fast parallel acquisition channel without adding a serial protocol driver. The 1 uA power-down current lets a node sleep for the majority of its duty cycle, and the 400 ksps rate supports burst capture of vibration or acoustic envelopes. Because the device accepts bipolar inputs, front ends with level-shifted sensor outputs can be connected directly. Its long-catalogued status and broad distributor availability make it a low-risk choice for volume programs that cannot wait for a new converter qualification cycle.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MAX152EAP+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX152CAP+ | MAX152EAP | MAX152EAP+T |
|---|---|---|---|---|
| Package | SSOP-20 | SSOP-20 - same | SSOP-20 - same | SSOP-20 - same |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Resolution | 8 bit | 8 bit | 8 bit | 8 bit |
| Conversion Architecture | Half-flash | Half-flash | Half-flash | Half-flash |
| Sampling Rate | 400 ksps | 400 ksps | 400 ksps | 400 ksps |
| Conversion Time | 1.8 us | 1.8 us | 1.8 us | 1.8 us |
| Supply Voltage | +3 V single or +/-3 V dual | +3 V single or +/-3 V dual | +3 V single or +/-3 V dual | +3 V single or +/-3 V dual |
| Power-Down Current | 1 uA typical | 1 uA typical | 1 uA typical | 1 uA typical |
| Input Signal Range | Unipolar or bipolar | Unipolar or bipolar | Unipolar or bipolar | Unipolar or bipolar |
| Output Interface | 8-bit parallel, microprocessor-compatible | 8-bit parallel, microprocessor-compatible | 8-bit parallel, microprocessor-compatible | 8-bit parallel, microprocessor-compatible |
| RoHS-Compliant Ordering Code | Yes ('+' suffix) | Yes ('+' suffix) | Legacy code without '+' finish | Yes ('+' suffix), tape-and-reel |
جیاکەرەوە سەرەکییەکان
- 400 ksps half-flash conversion with a 1.8 us conversion time in a legacy parallel-bus converter (بەراورد بەMAX152CAP+)
- Microprocessor-compatible parallel output avoids serial framing overhead (بەراورد بەMAX138EPL+)
- 1 uA typical power-down current suits battery-operated equipment (بەراورد بەADS1254E)
تێبینییەکانی دیزاین
Treat the analog input as a switched-capacitor sampling node rather than a high-impedance input. Place the input network and the reference bypass capacitor directly at the device pins, keep the analog trace short, and route the clock, write strobe and data bus on the opposite side of the board with a ground guard between them. Because the converter is a flash-style architecture, clock and strobe edges couple capacitively into the comparator array, and long parallel data runs next to the input are the most common cause of unstable last-count readings.
Estimated: in a duty-cycled design that wakes the converter for a burst of samples, the average supply current is dominated by the active conversion window, not the 1 uA power-down figure. With a 3 V supply, a 1.8 us conversion and, for example, 100 us of active time per burst, the average current contribution from the converter is roughly 100 uA over that burst, before the processor load. Add the reference bypass capacitor close to the REF pins and avoid placing a large bulk capacitor directly on the supply pin of the analog section, where switching charge would appear as supply ripple on the sampled code.
Two mistakes recur in designs that use this converter. First, driving the analog input from a high source impedance: the internal sampling network needs a low-impedance driver, so buffer the sensor output rather than relying on a resistive divider alone. Second, ignoring the reference path: the RDET and reference pins set the conversion scale, so keep them short, decouple the reference as shown in the manufacturer typical operating circuit, and avoid sharing the reference node with switching regulator outputs. Incorrect reference routing shifts the conversion span even when the digital code reads correctly.
The DB0-DB7 outputs are latch-driven on the write strobe, so the host processor must read the bus while the strobe is asserted and must not leave the data lines floating for long periods. Add pull-downs of a few tens of kilohms on the data bus if the processor resets or tri-states the lines during startup, otherwise a floating bus can present an undefined code. Because the device is powered down with 1 uA of supply current, the outputs may be indeterminate while powered down, so the firmware should ignore the bus until after the first conversion following a power-up.
زانیاری پابەندبوون
The '+' suffix in the MAX152EAP+ ordering code denotes the newer lead-free-compliant finish of the same MAX152 device, but no explicit RoHS, REACH or halogen-free statement was confirmed in the manufacturer documentation available for this page. The device is not an automotive-qualified part.