Analog Devices

MAX3095CEE+T - 10 Mbps Quad RS-422/485 Receiver | Analog Devices

MPN: MAX3095CEE+T ✓ چالاک
3 V/5 V Vdss RS-422/RS-485 Rds(on) 16-pin QSOP Package
MOQ: 1 |

MAX3095CEE+T گشتی

The Analog Devices MAX3095CEE+T is a 10 Mbps quad RS-422/RS-485 receiver with ±15 kV electrostatic-discharge protection, supplied in a 16-pin QSOP package. The device provides four independent receiver channels for differential data buses, operates from 3 V or 5 V supply rails, and is designed for industrial, telecommunications, and ESD-sensitive interface systems where surge protection and signal integrity are important.

A differential receiver is an interface circuit that converts a small voltage difference between two bus conductors into a valid logic signal. RS-422 and RS-485 belong to the differential-interface family, allowing information to be transmitted reliably over longer cable runs than conventional single-ended logic interfaces. The MAX3095 occupies the interface-IC hierarchy between transceiver components and the industrial communication equipment connected to them.

The MAX3095 series combines four receiver channels in one package, reducing board area compared with discrete receiver implementations. Its 10 Mbps maximum data rate supports high-speed industrial communication, while the integrated electrostatic-discharge protection helps protect sensitive receiver inputs. The manufacturer describes the MAX3095 and MAX3096 as rugged, low-power, pin-compatible upgrades to the industry-standard 26LS32 receiver.

Each receiver converts the differential voltage applied to its input pair into a CMOS-compatible output. Independent channels allow one package to serve four bus inputs or to support multiple data links. This integration is particularly useful in interface-dense equipment where repeated protection, receiver thresholds, and logic-level conversion would otherwise require several separate devices. The receiver architecture is suitable for data rates up to 10 Mbps.

Typical applications include industrial control systems, telecommunications equipment, RS-485 data acquisition, level translation, and receivers used in ESD-sensitive equipment. The MAX3095CEE+T is particularly appropriate when four channels are needed near a connector or board edge where electrostatic-discharge exposure is elevated. Because each channel is independently terminated and filtered internally, system-level design still requires correct bus topology, grounding, and termination practices.

For layout, place the device close to the protected connector and route each differential pair as a tightly coupled pair on the printed circuit board. Keep the receiver ground connection short, provide a clean ground reference, and observe the supply-voltage requirements for the selected 3 V or 5 V operating mode. The 16-pin QSOP package is compact, but exposed connector leads and narrow inter-pin spacing require careful assembly planning.

This product page combines the manufacturer's device description, package and interface characteristics, verified source links, drop-in family options, and practical PCB guidance. It is intended to help engineers evaluate the MAX3095CEE+T for four-channel differential reception, confirm the 10 Mbps and ESD-protection requirements, and plan a robust industrial-interface layout before requesting a quote.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3095CEE+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3095CEE+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Supply Voltage, Package, Data Rate, Interface Standards, RoHS Status.

Analog Devices
Supply Voltage: 4.75 V to 5.25 V (5 V nominal)
Data Rate: 10 Mbps (minimum)
RoHS Status: Compliant
بەراوردکردن لەگەڵ MAX3095CEE+T →
Analog Devices
Supply Voltage: 5 V
Data Rate: 10 Mbps
بەراوردکردن لەگەڵ MAX3095CEE+T →
Analog Devices
Supply Voltage: 3 V to 5 V
Package: 16-pin SOIC
Data Rate: 10 Mbps
بەراوردکردن لەگەڵ MAX3095CEE+T →

MAX3095EEE+T

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 16-QSOP
Quad RS-422/RS-485 receiver · 4 · 10 Mbps · 5 V · ±15 kV · ±8 kV · ±15 kV · RS-422 / RS-485

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3095CEE+

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 16-QSOP
Receiver (0/4 driver/receiver) · RS-422, RS-485 · 4 · 10 Mbps (minimum) · 4.75 V to 5.25 V (5 V nominal) · 13 mA typical (all channels active) · ±15 kV HBM · -7 V to +12 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3095CEE+T تایبەتمەندییەکان

Product Type Quad RS-422/RS-485 receiver
Number of Receiver Channels 4 channels
Maximum Data Rate 10 Mbps
Supply Voltage Operation 3 V/5 V
Interface Standards RS-422/RS-485
ESD Protection ±15 kV
Air-Gap ESD Test ±15 kV using IEC 1000-4-2
پاکێج 16-pin QSOP
جۆری دامەزراندن Surface mount
Power Consumption Low-power operation
Receiver Output Type Logic-level differential receiver

ڕێنمایی ڕێکخستنی پینی MAX3095CEE+T 16-pin qsop

ڕێکخستنی پین بۆ MAX3095CEE+T (پاکێجی 16-pin qsop). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 16-pin qsop بۆ MAX3095CEE+T

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3095CEE+T.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3095CEE+T گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Control Systems, Telecommunications Equipment Interfaces, RS-485 Data Acquisition, ESD-Sensitive Communication Ports, Level Translation and Protocol Bridging, High-Speed Differential Bus Reception.

🏭

Industrial RS-485 Control Systems

The MAX3095CEE+T fits industrial control equipment that must receive four differential RS-485 signals at rates up to 10 Mbps. Its four receiver channels reduce the component count required to monitor multiple bus nodes, while the ±15 kV ESD rating strengthens the interface close to external cabling and industrial connectors. The 16-QSOP package also preserves board area compared with four separate receiver packages. Designers should still validate grounding, cable routing, protection networks, and the complete industrial EMC design around the receiver.

🌐

Telecommunications Equipment Interfaces

In telecommunications equipment, the MAX3095CEE+T can provide four compact RS-422 or RS-485 receive channels for signaling and supervisory data links. The 10 Mbps capability accommodates relatively fast control traffic, and the integrated ±15 kV ESD protection is useful where receiver inputs connect to external backplanes or field wiring. Its low-power, space-saving QSOP construction supports dense line-card designs. Engineers should confirm common-mode limits and supply levels against the actual cable environment before finalizing the interface.

📊

RS-485 Data Acquisition

The MAX3095CEE+T is suitable for multichannel data-acquisition equipment that combines several RS-485 sensors, meters, or remote modules. Four independent receiver channels support parallel differential inputs, and the 10 Mbps rating provides margin for high-speed telemetry. The integrated ESD protection reduces reliance on discrete input protection close to the connector. System designers should preserve the recommended differential trace geometry, provide a low-impedance reference ground, and apply bus termination only where required by the selected network topology.

🔌

ESD-Sensitive Communication Ports

The MAX3095CEE+T fits communication ports where user-accessible connectors expose the receiver to electrostatic discharge. All four channels include protection identified by Analog Devices as ±15 kV using an IEC 1000-4-2 air-gap discharge test. Placing the receiver near the entry point can shorten unprotected PCB traces and improve system robustness. This capability should form part of a broader ESD-control plan involving enclosure grounding, shield design, connector selection, and board cleanliness rather than acting as a complete surge-protection solution.

🔄

Level Translation and Protocol Bridging

The MAX3095CEE+T can serve as the receiving stage in interface assemblies that translate between differential bus signaling and local CMOS logic. Its 3 V or 5 V operation allows connection to systems with different logic rails, while the four-channel arrangement supports compact protocol or data-routing modules. The receiver must be paired with an appropriate line driver or transceiver when bidirectional communication is required. Signal timing, propagation delay, and logic thresholds should be included in the end-to-end interface timing budget.

⚡

High-Speed Differential Bus Reception

For high-speed differential bus reception, the MAX3095CEE+T provides a 10 Mbps data-rate ceiling and four independent receive channels in one package. This combination is useful in multi-drop industrial links, test systems, and embedded interface modules that need compact channel density. Designers should treat the 10 Mbps figure as a system constraint rather than an unconditional guarantee, because cable length, topology, stubbing, common-mode range, and propagation characteristics determine practical signaling distance. Validate the complete channel against the required data rate and noise margin.

What is the MAX3095CEE+T?
The MAX3095CEE+T is a four-channel RS-422/RS-485 differential receiver rated for data rates up to 10 Mbps and protected to ±15 kV ESD. Analog Devices describes the MAX3095 family as a rugged, low-power upgrade to the 26LS32, with all four receivers integrated into a 16-pin QSOP package for industrial and telecommunications equipment.
What are the key specifications of MAX3095CEE+T that engineers should know?
The principal MAX3095CEE+T specifications are four RS-422/RS-485 receiver channels, a 10 Mbps maximum data rate, 3 V/5 V operation, ±15 kV ESD protection, and a 16-pin QSOP package. According to the Analog Devices MAX3095 product page, the receiver inputs use IEC 1000-4-2 air-gap discharge protection for systems exposed to electrostatic discharge.
Where can I download the MAX3095CEE+T datasheet PDF?
The official MAX3095 datasheet and product information are available from Analog Devices at the product-page URL shown on this page. The manufacturer document describes the MAX3095/MAX3096 quad receivers, ESD ratings, electrical characteristics, applications, and package options. Use the Analog Devices page to obtain the current manufacturer PDF and its product-selection information.
Where is the MAX3095CEE+T pinout?
The MAX3095CEE+T pinout is published in the Analog Devices MAX3095 manufacturer datasheet under the pin-description section. The device is a 16-pin QSOP with four differential receiver channels, power connections, and ground pins. Use that pin-description table when assigning connector, supply, and return connections on the PCB.
How does the MAX3095CEE+T compare with the MAX3095EEE+T?
The MAX3095CEE+T and MAX3095EEE+T both belong to the MAX3095 family and retain the same 10 Mbps receiver architecture, 16-QSOP format, and ±15 kV ESD-protection positioning. Their principal ordering distinction is the package temperature-grade suffix, so engineers must verify the required temperature range and ordering details in the manufacturer datasheet before treating either device as interchangeable.
What is the difference between MAX3095CEE+T and MAX3095CEE+?
The MAX3095CEE+T and MAX3095CEE+ share the same MAX3095 10 Mbps, four-channel RS-422/RS-485 receiver configuration and 16-QSOP package. The T suffix identifies the tape-and-reel ordering option, while the core receiver specifications remain unchanged. Verify the exact shipping format, terminal orientation, and temperature grade against the current manufacturer ordering information.
When should I choose MAX3095CEE+T over another quad RS-485 receiver?
Choose the MAX3095CEE+T when a design needs four independent RS-422/RS-485 channels, operation up to 10 Mbps, and ±15 kV-protected inputs in a 16-pin QSOP package. Compare alternatives by checking pinout, receiver thresholds, common-mode range, supply voltage, propagation delay, temperature grade, and availability rather than relying only on the number of channels and nominal data rate.
Is MAX3095CEE+T suitable for industrial RS-485 equipment?
The MAX3095CEE+T is suitable for industrial interface sections that require four differential receiver channels, 10 Mbps-class operation, and ±15 kV ESD protection. Its 3 V/5 V supply flexibility supports both logic systems. The complete design must still meet applicable industrial EMC, grounding, surge, isolation, and safety requirements outside the IC's specified ESD capability.
What can replace MAX3095CEE+T?
The closest documented drop-in family option is the MAX3095EEE+T, which retains the MAX3095 10 Mbps four-channel receiver architecture in a 16-QSOP package. Before replacement, confirm temperature grade, pin mapping, receiver thresholds, common-mode range, enable or fail-safe behavior, and supply requirements in the manufacturer datasheet. A cross-brand substitute should not be assumed without a verified pin-to-pin comparison.
Can MAX3095EEE+T replace MAX3095CEE+T on the same PCB?
The MAX3095EEE+T can serve as a candidate drop-in replacement because both devices are listed in the same MAX3095 family with a 16-QSOP package and 10 Mbps receiver rating. Final substitution still requires checking the temperature-grade suffix and electrical limits because the ordering codes target different commercial temperature ranges. PCB changes should not be assumed until those comparisons pass.
What is the best Analog Devices alternative for MAX3095CEE+T?
The MAX3095EEE+T is the closest Analog Devices family alternative identified for the MAX3095CEE+T because it combines the same four-channel RS-422/RS-485 receiver role, 10 Mbps data-rate class, and 16-QSOP package. The device differs in its temperature-grade ordering code, so qualification should confirm that its operating range covers the target environment and that all electrical limits remain acceptable.
How much ESD protection does MAX3095CEE+T provide?
The MAX3095CEE+T provides ±15 kV ESD protection on all receiver inputs. Analog Devices identifies the protection method as an IEC 1000-4-2 air-gap discharge test. This rating addresses electrostatic-discharge exposure at the interface IC, but it does not eliminate the need for system-level grounding, shielding, cable design, and external surge protection where the equipment faces larger transients.
How should MAX3095CEE+T be laid out for ESD protection?
Place the MAX3095CEE+T close to the external connector and route each differential receiver pair as a short, tightly coupled PCB trace. Connect the interface ground with a low-impedance path and keep sensitive logic traces away from connector-side return currents. The ±15 kV device rating helps at the receiver inputs, but physical placement, grounding, and enclosure design determine how much system-level stress actually reaches the IC.
Where can I buy MAX3095CEE+T and what is its lead time?
Use the Request a Quote form on this page to request current availability, lead time, order quantity, and commercial terms for the MAX3095CEE+T. Quote-based fulfillment may change by date and quantity, so current status should be confirmed through the form rather than inferred from an old listing or generic distributor result.
Is MAX3095CEE+T in stock?
Current stock for the MAX3095CEE+T should be confirmed through the Request a Quote form on this page because inventory can change independently of the product lifecycle. The part is a tape-and-reel ordering option in a 16-pin QSOP package, and the requested quantity determines how the order should be scheduled and consolidated.
What is the price of MAX3095CEE+T?
Current pricing for the MAX3095CEE+T is available through the Request a Quote form on this page. The request should specify the required quantity, tape-and-reel format, destination, and target delivery date so the commercial response can reflect the appropriate supply terms and production planning needs.
How much lead time should I allow for MAX3095CEE+T?
The current lead time for MAX3095CEE+T depends on order quantity, inventory position, and delivery requirements. Submit a request through the Request a Quote form on this page with your required quantity and schedule. For production planning, treat the confirmed lead time from that response as the applicable commercial commitment rather than relying on a historical listing.

داتای سەرچاوەی ئەندازیاری بۆ MAX3095CEE+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the MAX3095CEE+T when the design needs four RS-422 or RS-485 receive channels, operation up to 10 Mbps, and ±15 kV ESD protection in a 16-pin QSOP package. It is well suited to industrial, telecommunications, data-acquisition, and connector-adjacent interface circuits. The MAX3095EEE+T is the closest family option when its temperature grade covers the intended environment; its core receiver configuration and package remain the same, but the ordering suffix must be checked. The MAX3095CEE+ offers the same core device configuration without the T shipping suffix and may suit procurement formats that do not require that option. For any cross-brand replacement, require a verified pin-to-pin comparison covering thresholds, common-mode range, propagation delay, supply current, temperature range, and ESD ratings. Do not select solely by channel count and data rate, and do not treat the on-chip ESD rating as a substitute for external surge protection.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3095EEE+T MAX3095CEE+
Brand Analog Devices Analog Devices Analog Devices
Package 16-QSOP 16-QSOP - same 16-QSOP - same
Receiver Channels 4 channels 4 channels 4 channels
Maximum Data Rate 10 Mbps 10 Mbps 10 Mbps
Interface Standards RS-422/RS-485 RS-422/RS-485 RS-422/RS-485
ESD Protection ±15 kV ±15 kV ±15 kV
Ordering Code Difference CEE temperature-grade and T tape-and-reel suffix EEE temperature-grade suffix with T tape-and-reel format CEE grade without T shipping suffix

جیاکەرەوە سەرەکییەکان

  • Four protected differential receiver channels in one package (بەراورد بەMAX3095CEE+)
  • Same 10 Mbps receiver performance within the MAX3095 family (بەراورد بەMAX3095EEE+T)
  • Industrial differential-interface capability with 3 V and 5 V operation (بەراورد بەMAX3095CEE+)

تێبینییەکانی دیزاین

Place the MAX3095CEE+T close to the external connector so the protected receiver inputs remain close to the board entry point and away from long unprotected copper routes. Route each RS-422 or RS-485 pair together with consistent spacing and minimize vias. A short, low-impedance ground connection provides the return reference for the differential receiver and reduces sensitivity to common-mode voltage and ESD-generated currents.

Separate connector-side protection and high-current return paths from receiver traces and local supply components. Use a continuous ground plane beneath the interface area, and place input-side bypass capacitance near the device supply pins. Avoid routing sensitive receiver inputs beneath power inductors, relays, motor-control traces, or other sources of large switching transients, because the IC's ±15 kV ESD rating does not remove the need for careful signal isolation.

Do not treat the MAX3095EE/T suffix as cosmetic: confirm the temperature grade, tape-and-reel format, pin orientation, and electrical limits for the exact ordering code. Also avoid assuming that every receiver labeled RS-485 supports identical common-mode range, thresholds, fail-safe behavior, or propagation delay. Verify those characteristics in the manufacturer datasheet before substituting a family member or designing cable length and termination.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The Analog Devices product page identifies IEC 1000-4-2 air-gap discharge protection for the receiver inputs. Other environmental, material, and automotive compliance declarations require confirmation from the current manufacturer product documentation.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3095CEE+T datasheet MAX3095CEE+T pinout MAX3095CEE+T datasheet pdf MAX3095CEE+T equivalent MAX3095CEE+T replacement MAX3095CEE+T cross reference MAX3095CEE+T price MAX3095CEE+T stock Analog Devices MAX3095CEE+T MAX3095 16-QSOP pinout MAX3095 10 Mbps receiver MAX3095 industrial RS-485 receiver MAX3095CEE+T vs MAX3095EEE+T MAX3095CEE+T footprint

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices MAX3095CEE+T MAX3095EEE+T MAX3095CEE+ MAX3095 RS-422 RS-485 differential receiver receiver IC interface IC semiconductor quad receiver 10 Mbps ±15 kV ESD protection IEC 1000-4-2 3 V operation 5 V operation 16-QSOP QSOP package surface-mount package industrial control telecommunications equipment RS-485 data acquisition electrostatic discharge level translation
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ