MAX3095EEE+ - 10Mbps Quad RS-422/RS-485 Receiver | Maxim
MPN: MAX3095EEE+ ✓ چالاکMAX3095EEE+ گشتی
A differential line receiver is a type of interface IC in the transceiver family. It belongs to the hierarchy receiver IC -> line driver/receiver -> differential interface transceiver -> interface IC -> integrated circuit. Its job is to convert a small differential voltage appearing across a twisted pair into a single-ended logic level that a microcontroller, DSP, or FPGA can read, while rejecting common-mode noise picked up along the cable run.
Key differentiating features include ±15 kV human-body-model ESD protection rated to IEC 61000-4-2 on the receiver inputs, 45 mV of receiver hysteresis for noise immunity and glitch-free operation, 10 Mbps maximum signalling rate for legacy and industrial buses, and low supply current for space-constrained embedded designs. The device is intended for harsh environments where cables exit the enclosure and are exposed to electrostatic discharge events.
Technically, each receiver compares the differential input against a threshold with 45 mV of hysteresis, preventing output chatter when the bus is idle or when common-mode noise crosses the threshold. Because the receivers are true differential inputs, they work with both RS-422 point-to-point topologies and RS-485 multidrop buses, and the 10 Mbps ceiling comfortably exceeds the 1 Mbps to 10 Mbps range typical of industrial Modbus RTU links.
Typical applications include RS-485 industrial automation and PLC bus nodes, RS-422 telecommunication equipment links, ESD-sensitive receiver front-ends, camera and PTZ control over RS-485, level translation between legacy '26LS32 systems and modern logic, and data-acquisition instrumentation.
When designing with the MAX3095EEE+, remember that it is receive-only: a companion RS-485 driver such as a MAX3485 or a TCAN-style transceiver is required for a complete node. Terminate the bus at both physical ends with 120 ohm resistors and provide proper decoupling close to the VCC and GND pins.
This page consolidates distributor pricing as of 2026-10-28, verified drop-in alternatives, and practical layout and bus-integration notes that are not found together in the original manufacturer datasheet.
جێگرەوەکانی جێگۆڕکێ بۆ MAX3095EEE+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3095EEE+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Supply Voltage, Mounting Type, Number of Receivers.
MAX3095CSE+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX3095EET+
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3095CEE+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX3095CEE+
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MAX3096EEE+
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3096CSE+
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3095EEE+ تایبەتمەندییەکان
| Product Type | Quad differential line receiver (RS-422/RS-485) |
| Number of Receivers | 4 |
| Number of Drivers | 0 (receive-only device) |
| Maximum Data Rate | 10 Mbps |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Family Supply Options | 3 V / 5 V (MAX3095/MAX3096 family) |
| ESD Protection | ±15 kV |
| ESD Standard | IEC 61000-4-2 |
| Receiver Hysteresis | 45 mV |
| Supported Protocols | RS-422, RS-485, RS-423 |
| پاکێج | QSOP-16 (0.154", 3.90 mm wide) |
| ژمارەی پین | 16 |
| جۆری دامەزراندن | Surface Mount |
| Logic Compatibility | Pin-compatible with industry-standard '26LS32 |
ڕێنمایی ڕێکخستنی پینی MAX3095EEE+ qsop-16 (0.154", 3.90 mm wide)
ڕێکخستنی پین بۆ MAX3095EEE+ (پاکێجی qsop-16 (0.154", 3.90 mm wide)). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3095EEE+.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX3095EEE+ گونجاوە بۆ 6 بەکارھێنانs: RS-485 Industrial Automation Bus Receiver, RS-422 Telecommunication Equipment Links, ESD-Sensitive Rugged Receiver Front-End, Camera and PTZ Surveillance Control Bus, Legacy '26LS32 Receiver Upgrade, Level Translation Between Legacy and Modern Logic.
RS-485 Industrial Automation Bus Receiver
The MAX3095EEE+ is a natural fit for the receive side of an RS-485 industrial bus node because its 10 Mbps rating far exceeds the 1 Mbps typical of Modbus RTU and the 45 mV receiver hysteresis rejects the common-mode ripple that appears when long factory cable runs share a ground reference with switching equipment. Four independent receivers let one package absorb four separate bus taps or two full duplex pairs, and the ±15 kV IEC 61000-4-2 input protection survives the electrostatic discharge events that occur when cables are unplugged from a live cabinet. In a PLC or sensor-hub design, the receiver sits between the RS-485 bus screw terminal and the MCU UART, with 120 ohm termination placed only at the two physical ends of the trunk. The trade-off is that this is a receive-only device, so a companion driver is mandatory for any node that must transmit.
پێشنیارکراو
RS-422 Telecommunication Equipment Links
Point-to-point RS-422 links in telecommunication and data-communications equipment are the classic use case for the MAX3095EEE+, since the device delivers four differential receivers in a single 16-QSOP package and is documented as a pin-compatible, low-power upgrade to the standard '26LS32. A 10 Mbps data rate supports backplane and shelf-to-shelf interconnects as well as slower tributary links, while the low supply current suits line-card designs where dozens of receivers share one rail. Because QSOP-16 offers a narrow 0.154" body, the receiver can be placed behind a 16-pin connector on dense mezzanine boards. Keep the differential pair impedance controlled and route the pair as a coupled pair to preserve the noise rejection that the 45 mV threshold is designed to exploit.
پێشنیارکراو
ESD-Sensitive Rugged Receiver Front-End
Where field cables terminate in an enclosure, the MAX3095EEE+ adds a layer of protection that a plain '26LS32 cannot match: ±15 kV ESD protection rated to IEC 61000-4-2 on all four differential inputs. That rating is meaningful in real deployments because the standard IEC 61000-4-2 discharge test models the human-body contact that occurs when a technician touches an exposed connector shell. The 45 mV hysteresis of each receiver also keeps outputs stable during and after a discharge event, avoiding false data frames being parsed by the host controller. Note that the protection is on the receiver inputs only, so the board still needs proper chassis grounding, shield termination, and surge suppression on the connector shell for a full industrial EMC design.
پێشنیارکراو
Camera and PTZ Surveillance Control Bus
The MAX3095EEE+ works well in the control path of surveillance systems, where a single RS-485 coax-like pair carries pan, tilt, and zoom commands from a keyboard or DVR to many dome cameras daisy-chained on one bus. The 10 Mbps capability gives ample headroom over the 9600 to 115200 baud rates typical of legacy CCTV control protocols, and the ±15 kV ESD rating protects the DVR rack when installers patch long outdoor cables. Four receivers in one 16-QSOP package can also handle the return acknowledgements from four camera positions. The design point to watch is biasing: RS-485 requires a fail-safe bias resistor network at the master so that an unterminated or disconnected camera does not pull the bus to an undefined level and cause spurious commands.
پێشنیارکراو
Legacy '26LS32 Receiver Upgrade
Designers migrating away from the aging '26LS32 quad differential receiver can drop the MAX3095EEE+ onto the same 16-pin footprint because the manufacturer explicitly positions the MAX3095/MAX3096 as pin-compatible, low-power upgrades to that industry-standard part. The migration delivers three concrete benefits: ±15 kV IEC 61000-4-2 input protection that the original '26LS32 never offered, 45 mV hysteresis for improved noise immunity, and lower supply current for battery-backed or space-constrained instrumentation. Because the family is also offered in narrow SOIC-16 and extended-temperature order codes, an existing '26LS32 land pattern can be reused without respinning the board for thermal or sourcing reasons. Verify the enable/shutdown pin usage on the MAX3096 before swapping in that variant.
پێشنیارکراو
Level Translation Between Legacy and Modern Logic
The MAX3095EEE+ also serves as a level translator when a legacy '26LS32-based subsystem must interoperate with 3.3 V or 5 V modern logic rails. The differential input accepts whatever signal swings the RS-422/RS-485 bus presents, while the single-ended CMOS outputs match the host MCU, DSP, or FPGA supply level, allowing old and new domains to coexist without level-shifter ICs on every signal. The MAX3095/MAX3096 family is specified for both 3 V and 5 V operation, and this 5 V ordering code uses a 4.75 V to 5.25 V supply. Keep the receiver supply aligned with the logic domain of the receiving controller, and confirm the output logic levels in the datasheet electrical characteristics table when interfacing to a 1.8 V core.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MAX3095EEE+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX3095CSE+ | MAX3095EET+ | MAX3095CEE+ | MAX3095CEE | MAX3096EEE+ |
|---|---|---|---|---|---|---|
| Package | QSOP-16 (0.154", 3.90 mm wide) | SOIC-16 narrow - same 16-pin land pattern | QSOP-16 - identical | QSOP-16 - identical | QSOP-16 - identical | QSOP-16 - identical |
| Brand | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) | Maxim Integrated (Analog Devices) |
| Number of Receivers / Drivers | 4 receivers / 0 drivers | 4 receivers / 0 drivers | 4 receivers / 0 drivers | 4 receivers / 0 drivers | 4 receivers / 0 drivers | 4 receivers / 0 drivers |
| Maximum Data Rate | 10 Mbps | 10 Mbps | 10 Mbps | 10 Mbps | 10 Mbps | 10 Mbps |
| ESD Protection | ±15 kV (IEC 61000-4-2) | ±15 kV (IEC 61000-4-2) | ±15 kV (IEC 61000-4-2) | ±15 kV (IEC 61000-4-2) | ±15 kV (IEC 61000-4-2) | ±15 kV (IEC 61000-4-2) |
| Receiver Hysteresis | 45 mV | 45 mV | 45 mV | 45 mV | 45 mV | 45 mV |
| Supply Voltage | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V | 4.75 V to 5.25 V |
| Shutdown Control | No | No | No | No | No | Yes - shutdown pin present |
| Logic Compatibility | '26LS32 pin-compatible | '26LS32 pin-compatible | '26LS32 pin-compatible | '26LS32 pin-compatible | '26LS32 pin-compatible | '26LS32 pin-compatible |
جیاکەرەوە سەرەکییەکان
- ±15 kV IEC 61000-4-2 ESD protection on all receiver inputs (بەراورد بەDS90LV017M)
- Drop-in 16-pin compatibility with the legacy '26LS32 footprint (بەراورد بەMAX3095CEE)
- Four independent receivers consolidated in one 16-QSOP body (بەراورد بەMAX3096EEE+)
- 10 Mbps data rate with 45 mV hysteresis for noisy industrial buses (بەراورد بەMAX3095CSE+)
تێبینییەکانی دیزاین
Keep the differential input traces short and tightly coupled, routing the + and - pair as a pair with continuous reference to a ground plane. Because the 45 mV receiver threshold is small, any asymmetry between the two legs translates directly into differential noise at the input. Place the ESD-protection return path and the input pair entry close to the connector so surge current is diverted before it reaches the IC pins, and avoid routing the pair adjacent to switching-regulator or relay nodes.
The most common design error is treating the MAX3095EEE+ as a transceiver. It contains zero drivers, so a node that must transmit needs a separate RS-485/RS-422 driver in addition to these receivers. The second common error is forgetting bus termination: place 120 ohm resistors only at the two physical ends of the RS-485 trunk, never at every node, and add fail-safe bias resistors at the master so an unterminated or disconnected slave cannot drag the bus to an undefined level.
Decouple the single 4.75 V to 5.25 V supply with a 0.1 uF ceramic capacitor placed immediately adjacent to the VCC and GND pins, backed by a bulk capacitor near the connector. The ±15 kV IEC 61000-4-2 rating protects only the receiver inputs; it does not protect the supply rail from a conducted discharge event, so a series ferrite or a dedicated surge stopper on the connector side of the board adds margin. Estimated note: at 5.0 V and a 3 mA receiver load, IC dissipation is roughly 15 mW, so no heatsinking is required.
Before substituting a MAX3095CSE+ or MAX3095EET+ into an existing design, confirm both the package body width and the temperature grade of your layout. The CSE+ uses the narrow SOIC-16 body while the EEE+ and EET+ use the 16-QSOP body, so a footprint intended for one may need a different land pattern if the silkscreen and pad geometry differ. Also verify the shutdown pin usage: the MAX3096 adds a shutdown control, while the MAX3095 has no such pin.
زانیاری پابەندبوون
Compliance status was not explicitly stated in the retrieved distributor or manufacturer page data, so RoHS, REACH, lead-free, halogen-free and conflict-minerals fields are left as unknown rather than assumed. The MAX3095EEE+ ordering code carries the '+' suffix used by Maxim for lead-free/RoHS-compliant material, but this was not confirmed verbatim in the source data. The part is a commercial/industrial interface IC with no AEC-Q100 automotive qualification listed.