Analog Devices

MAX3095ESE+T - 10Mbps Quad RS-422/RS-485 Receiver | Analog Devices

MPN: MAX3095ESE+T ✓ چالاک
3V or 5V Vdss RS-422 and RS-485 Rds(on) 16-pin SOIC, 0.154" (3.90mm) width Package
MOQ: 1 |

MAX3095ESE+T گشتی

The Analog Devices MAX3095ESE+T is a rugged, low-power, quad RS-422/RS-485 receiver with electrostatic discharge protection, a maximum data rate of 10Mbps, and operation from 3V or 5V supplies in a 16-pin SOIC package. All four receiver channels are designed for differential bus reception in electrically noisy industrial environments.

An RS-485 receiver is an interface integrated circuit that converts small differential voltage signals appearing on a balanced bus into a logic-level output for a host controller. The MAX3095 supports both RS-422 point-to-point and RS-485 multidrop networks, placing it within the hierarchy of interface IC, bus transceiver, line receiver, and communications IC. Its quad-channel architecture allows one component to serve four independent data lines or two full-duplex links.

Key features include ±15kV ESD protection using the IEC 1000-4-2 air-gap discharge method, ±8kV protection using IEC 1000-4-2 contact discharge, and a data rate of 10Mbps. The device operates from 3V/5V supplies, consumes low power, and is offered in the space-saving 16-SOIC package. These characteristics suit industrial controllers, telecom equipment, level translators, and receivers exposed to ESD-sensitive interfaces.

The MAX3095 and MAX3096 are described by Analog Devices as pin-compatible, low-power upgrades to the industry-standard 26LS32. Within the receiver family, the MAX3095 is the quad RS-422/RS-485 choice, while the MAX3096 supports the related RS-423 interface. The MAX3095ESE+T ordering code identifies the Analog Devices extended-temperature SOIC variant supplied in tape-and-reel packaging.

Typical applications include industrial programmable logic controller communication ports, factory automation equipment, telecommunications racks, building-control systems, and data-acquisition equipment. Multiple receiver channels can monitor machine sensors, encoder buses, or remote I/O modules while sharing a common ground and supply architecture.

When laying out a board, keep each differential receiver pair tightly routed as a controlled-impedance pair and place protection components close to the connector entry point. Confirm termination and biasing requirements against the bus topology. The MAX3095 protects the receiver inputs, but it does not replace external surge protection for severe industrial transients.

This page combines manufacturer device information, distributor availability references, package and interface details, and practical design guidance for engineers evaluating the MAX3095ESE+T in 3V or 5V RS-422, RS-485, and ESD-sensitive receiver applications.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3095ESE+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3095ESE+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Automotive Qualification, ESD Test Method, Number of Receivers, Product Type.

Analog Devices
Package: 16-pin SOIC
Automotive Qualification: Not specified in verified data
ESD Test Method: IEC 1000-4-2
بەراوردکردن لەگەڵ MAX3095ESE+T →
Analog Devices
Package: 16-pin SOIC
Automotive Qualification: unknown
ESD Test Method: IEC 1000-4-2 Air-Gap Discharge; additional protected levels per manufacturer product data
بەراوردکردن لەگەڵ MAX3095ESE+T →

MAX3096ESE+T

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 16-SOIC
RS-423 receiver instead of the MAX3095's RS-422/RS-485 function; same MAX3095/MAX3096 pin-compatible family and 16-SOIC footprint

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3096CSE+T

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 16-SOIC
RS-423 receiver and a different package/temperature suffix; retains the pin-compatible MAX3095/MAX3096 family interface and 10Mbps-class receiver function

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3095CSE+T

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 16-SOIC
Quad differential line receiver · 4 channels · RS-422 and RS-485 · 10Mbps · 3V or 5V · ±15kV air-gap discharge · ±8kV contact discharge · IEC 1000-4-2

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3095ESE+

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 16-SOIC
Quad RS-422/RS-485 receiver · 4 · 10 Mbps · 3 V to 5 V · ±15 kV · 16-pin SOIC · RS-422 and RS-485

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3095ESE+T تایبەتمەندییەکان

Receiver Configuration Quad receiver
Supported Standards RS-422 and RS-485
Maximum Data Rate 10Mbps
Supply Voltage Options 3V or 5V
ESD Protection, Air-Gap Discharge ±15kV using IEC 1000-4-2
ESD Protection, Contact Discharge ±8kV using IEC 1000-4-2
Device Type RS-422/RS-485 line receiver
Power Consumption Low-power design
پاکێج 16-pin SOIC, 0.154" (3.90mm) width
جۆری دامەزراندن Surface mount
Manufacturer Description Rugged, low-power, quad RS-422/RS-485 receiver for harsh environments
Reference Receiver Industry-standard 26LS32
Family Compatibility MAX3095 and MAX3096 are pin-compatible

ڕێنمایی ڕێکخستنی پینی MAX3095ESE+T 16-pin soic, 0.154" (3.90mm) width

ڕێکخستنی پین بۆ MAX3095ESE+T (پاکێجی 16-pin soic, 0.154" (3.90mm) width). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 16-pin soic, 0.154" (3.90mm) width بۆ MAX3095ESE+T

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3095ESE+T.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3095ESE+T گونجاوە بۆ 6 بەکارھێنانs: Industrial PLC and Factory Automation Interfaces, Telecommunications Equipment and Racks, Building Control and HVAC Networks, Data Acquisition and Sensor Interface Boards, ESD-Sensitive External Cable Interfaces, Robotics and Motor-Control Coordination Links.

🏭

Industrial PLC and Factory Automation Interfaces

The MAX3095ESE+T fits industrial controller boards that must monitor several field buses through one 16-pin device. Its four receiver channels can cover four single-ended-ended differential links or two bidirectional pairs, while 10Mbps operation provides headroom for fast sensor and motion-control traffic. The ±15kV IEC 1000-4-2 air-gap and ±8kV contact ratings are especially relevant where field cables enter an enclosure through unprotected connectors. Use a 3V or 5V supply selected to match the controller interface, and route each differential pair away from switching nodes and motor-drive traces.

🌐

Telecommunications Equipment and Racks

The MAX3095ESE+T is appropriate for telecommunications interface cards that receive balanced signals from backplanes, remote terminals, or service equipment. Its low-power quad-receiver architecture preserves board area compared with four discrete line receivers, and the 10Mbps rating supports high-rate control or monitoring links. The specified IEC 1000-4-2 ESD protection improves resilience in maintenance and installation environments where cables are disconnected while powered. Confirm logic thresholds against the backplane controller and provide a continuous ground return alongside every differential pair.

🧩

Building Control and HVAC Networks

The MAX3095ESE+T can support building-control equipment that polls multiple floor controllers, sensors, or damper actuators over RS-485 networks. Four channels allow one receiver package to handle several independent point-to-point RS-422 links or paired RS-485 traffic. The 3V/5V flexibility supports both legacy controllers and modern embedded control boards, while the narrow SOIC package simplifies routing on densely populated automation boards. Use shielded or twisted-pair cabling according to the building installation environment and keep protective components near the external connector.

📡

Data Acquisition and Sensor Interface Boards

The MAX3095ESE+T suits measurement systems that must recover data from multiple differential sensor or instrument links. Its four channels consolidate receivers while maintaining a 10Mbps maximum rate, and the low-power design suits compact multi-channel acquisition hardware. The MAX3095's RS-422 compatibility is particularly useful for point-to-point links to instrumentation that use balanced outputs. Match receiver thresholds and common-mode limits to the selected sensors, and terminate each transmission line at the appropriate endpoint rather than adding termination indiscriminately.

🛡️

ESD-Sensitive External Cable Interfaces

The MAX3095ESE+T is a strong choice when external cables terminate directly at a board carrying sensitive low-level logic. Every receiver input is protected to ±15kV under IEC 1000-4-2 air-gap discharge and ±8kV under contact discharge, providing a specified margin for electrostatic events. The 10Mbps capability permits high-speed differential links without lowering the bus specification. Keep the analog input section short, use a solid ground plane, and place optional TVS protection at the connector boundary if the installation faces surge or lightning exposure.

🤖

Robotics and Motor-Control Coordination Links

The MAX3095ESE+T can receive position, limit, and status information from distributed robot modules over balanced links. Quad-channel operation reduces the component count on a central motion-control board, and 10Mbps bandwidth is more than sufficient for many encoder and safety-status feedback paths. ESD protection improves reliability around motors, cables, and service connectors that are frequently touched. Keep the receiver away from stepper and servo drive traces, use twisted-pair cabling, and maintain a low-impedance ground reference between the controller and remote modules.

What is the MAX3095ESE+T?
The MAX3095ESE+T is a rugged, low-power, quad RS-422/RS-485 receiver from Analog Devices. It converts four differential receiver inputs into logic signals, supports data rates up to 10Mbps, operates from 3V or 5V, and provides ±15kV IEC 1000-4-2 air-gap ESD protection. The device is housed in a 16-pin SOIC package and is intended for industrial and telecommunications equipment exposed to electrically harsh interfaces.
What are the key specifications of MAX3095ESE+T that engineers should know?
The MAX3095ESE+T combines four RS-422/RS-485 receiver channels, a 10Mbps maximum data rate, 3V/5V operation, and reinforced ESD protection in one 16-pin SOIC. Analog Devices specifies ±15kV protection using the IEC 1000-4-2 air-gap discharge method and ±8kV using the contact-discharge method. Its low-power design targets level translation, telecommunications, and ESD-sensitive receiver applications where four independent bus inputs are required.
Where can I download the MAX3095ESE+T datasheet PDF?
The official MAX3095 product page on the Analog Devices website is the primary location for the MAX3095ESE+T datasheet, package information, and revision history. The device is also described as a pin-compatible, low-power upgrade to the industry-standard 26LS32 receiver. Use the manufacturer datasheet for the authoritative pin-description table, recommended application circuit, electrical characteristics, and operating limits before laying out the PCB.
Where can I find the MAX3095ESE+T pinout?
The MAX3095ESE+T pinout is published in the pin-description section of the manufacturer MAX3095 data sheet. The component uses a 16-pin narrow SOIC package, and its four channels are organized as differential receiver pairs. Use that diagram when assigning connector signals and confirming channel polarity. Because exposed-pad and thermal details are not relevant to this SOIC device, the package drawing is limited to the 16 perimeter pins.
What ESD protection does the MAX3095ESE+T provide?
Every MAX3095ESE+T receiver input is protected to ±15kV under the IEC 1000-4-2 air-gap discharge test and to ±8kV under the IEC 1000-4-2 contact-discharge test. This protection is intended for harsh industrial and telecommunications environments where cables can accumulate electrostatic charge. Connector-side surge protection remains a separate design requirement for transients that exceed the receiver's specified ESD ratings.
How fast is the MAX3095ESE+T RS-485 receiver?
The MAX3095ESE+T supports a maximum data rate of 10Mbps. This data rate applies to the receiver family identified by Analog Devices as the MAX3095/MAX3096 rugged, low-power quad receivers. The rate makes the device suitable for high-speed balanced data links and compact multidrop industrial networks, provided the cable, terminations, grounding, and baud rate remain consistent with the system design.
Can MAX3095ESE+T operate from a 3V supply?
Yes. The MAX3095ESE+T is specified for operation from 3V or 5V supplies, allowing it to fit both legacy 5V control electronics and lower-voltage embedded systems. Confirm the interface output levels against the host controller's supply voltage before connecting the receiver outputs. Analog Devices identifies the MAX3095/MAX3096 as low-power receivers intended for space-constrained industrial and telecom designs.
Where can I buy MAX3095ESE+T online?
The MAX3095ESE+T can be requested through the Request a Quote form on this page, where the exact MPN, package code, and target quantity should be confirmed. Current commercial availability and delivery schedules can change, so request the current lead time and stock position with the inquiry rather than relying on a cached listing status. The manufacturer product page and distributor records identify the part as a 16-SOIC quad RS-422/RS-485 receiver.
What is the price of MAX3095ESE+T?
Use the Request a Quote form on this page for the current MAX3095ESE+T commercial quotation. The form is the appropriate channel for quantity pricing, production scheduling, and order processing, because distributor prices and availability change with market conditions. Confirm the full ordering code, MAX3095ESE+T, and the tape-and-reel delivery format in the request to avoid ambiguity with other package or temperature suffixes.
What is the lead time for MAX3095ESE+T?
Request the current production lead time through the Request a Quote form on this page. Lead time depends on the ordered quantity, current inventory position, and manufacturer allocation at the time of quotation. The 16-SOIC package and MAX3095ESE+T ordering code should be stated explicitly in the request so the supplier can confirm the exact device configuration and scheduled delivery.
Is MAX3095ESE+T in stock?
Submit a stock and lead-time request with the Request a Quote form on this page. Inventory for this 16-SOIC ordering code varies with order quantity and purchasing activity, so a quantity-specific availability confirmation is more useful than a generic in-stock statement. Include your required delivery schedule and purchase quantity to obtain an actionable allocation response for MAX3095ESE+T.
What is the best drop-in replacement for MAX3095ESE+T?
The closest same-family replacement is a MAX3095 option with the same 16-pin SOIC footprint and compatible receiver configuration. The +T suffix identifies the tape-and-reel delivery format, so a replacement should be selected by its functional suffix as well as its package. Use the Request a Quote form to request availability of alternatives, and confirm pin compatibility, temperature grade, and ordering code before substitution.
When should I choose MAX3095ESE+T over another quad RS-485 receiver?
Choose the MAX3095ESE+T when the design requires four RS-422/RS-485 receiver channels, data rates up to 10Mbps, operation from 3V or 5V, and specified IEC 1000-4-2 ESD protection in a 16-pin SOIC package. Select another receiver instead if its protection rating, supply voltage, channel count, or package differs from these requirements. The choice is strongest for space-constrained industrial interfaces where four receivers share a common device.
Is MAX3095ESE+T the same as MAX3095ESE?
The MAX3095ESE and MAX3095ESE+T share the same 16-SOIC receiver configuration and 10Mbps data-rate rating. The +T code identifies the tape-and-reel packing option, while the base MAX3095ESE designation refers to a different delivery format. For a new board, use the complete MAX3095ESE+T ordering code when the assembly line requires tape-and-reel presentation.
What can replace MAX3095ESE+T?
A replacement must provide four compatible differential receiver channels in the same 16-pin SOIC footprint while meeting the required supply voltage, data rate, and ESD ratings. Same-family MAX3095 ordering options with a different packing suffix are the closest choices, and the manufacturer identifies the MAX3095/MAX3096 as pin-compatible. Verify the pin-description table and operating limits before approving any substitute or layout change.
What is the best Analog Devices equivalent for MAX3095ESE+T?
Analog Devices' MAX3096 is the closest named family member because Analog Devices describes the MAX3095 and MAX3096 as pin-compatible, low-power upgrades to the industry-standard 26LS32. The MAX3096 targets the related RS-423 interface, while the MAX3095 is the RS-422/RS-485 version. Select the MAX3096 only after checking its interface standard, enable or shutdown behavior, input thresholds, and complete pin descriptions against the intended circuit.

داتای سەرچاوەی ئەندازیاری بۆ MAX3095ESE+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose MAX3095ESE+T when a board needs four differential RS-422 or RS-485 receivers, a maximum rate of 10Mbps, and a 3V or 5V supply in a 16-pin SOIC package. Its specified ±15kV IEC 1000-4-2 air-gap and ±8kV contact protection make it especially appropriate for externally accessible industrial and telecom connectors. Choose MAX3096ESE+T only when the circuit specifically requires RS-423 rather than RS-422/RS-485. Choose MAX3095CSE+T when its temperature grade and package suffix better match the assembly, and choose MAX3095ESE+ when a non-tape-and-reel delivery format is preferred. For any substitution, confirm the complete pin-description table, supply range, receiver thresholds, common-mode limits, temperature grade, and ESD ratings before releasing the PCB.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3096ESE+T MAX3096CSE+T MAX3095CSE+T MAX3095ESE+
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-SOIC, 0.154" (3.90mm) width 16-SOIC 16-SOIC 16-SOIC 16-SOIC
Receiver Configuration Quad receiver Quad receiver Quad receiver Quad receiver Quad receiver
Interface Standard RS-422/RS-485 RS-423 RS-423 RS-422/RS-485 RS-422/RS-485
Maximum Data Rate 10Mbps 10Mbps 10Mbps 10Mbps 10Mbps
Supply Voltage 3V or 5V 3V or 5V 3V or 5V 3V or 5V 3V or 5V
Power Class Low-power receiver Low-power receiver Low-power receiver Low-power receiver Low-power receiver
Delivery Format Tape & Reel (+T) Tape & Reel (+T) Tape & Reel (+T) Tape & Reel (+T) Non-'-T' delivery format

جیاکەرەوە سەرەکییەکان

  • Four receiver channels in one narrow package (بەراورد بەMAX3095ESE+)
  • Specified IEC 1000-4-2 receiver protection (بەراورد بەMAX3096ESE+T)
  • 10Mbps performance with 3V/5V supply flexibility (بەراورد بەMAX3095CSE+T)

تێبینییەکانی دیزاین

Route each differential receiver input as a tightly coupled pair with continuous ground reference, and keep the two conductors of a pair at similar impedance and trace length. Place the receiver close to the connector entry point so connector-side protection can prevent large transients from propagating into the board. Avoid placing the pair beneath motor drivers, switching regulators, or high-current relay traces. Differential routing helps reject common-mode noise, but it does not compensate for an improper ground-return path.

Do not assume that the receiver's ±15kV IEC 1000-4-2 air-gap rating eliminates the need for external surge protection. That rating applies to specified electrostatic-discharge conditions, while lightning, switching spikes, and industrial surge events may require separate TVS devices. Also verify termination placement: in point-to-point RS-422 links, termination commonly belongs at the receiver end, while multidrop RS-485 networks have different termination and biasing rules. Confirm both against the selected bus topology.

The MAX3095ESE+T supports rates up to 10Mbps, but data rate alone does not guarantee reliable reception. Cable length, propagation delay, connector loss, topology, grounding, and termination determine the usable margin. Use twisted-pair cabling, minimize stub lengths, maintain a low-resistance ground path, and avoid excessive capacitive loading on the bus. When commissioning, verify differential voltage and eye margin at the receiver rather than relying only on the nominal baud rate.

Select the 3V or 5V configuration to match the receiver's permissible supply range and the logic thresholds of the connected controller. Place the device's bypass capacitors directly across the supply and ground pins, using the values and placement recommended in the manufacturer application circuit. Because all four channels share the same package supply pins, high transient current on one input can reference through the common ground network; use a low-impedance ground plane and decouple locally to reduce shared-impedance coupling.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The manufacturer product page identifies IEC 1000-4-2 ESD test methods for the receiver inputs. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statuses require confirmation from the current manufacturer product documentation or material declaration.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3095ESE+T datasheet MAX3095ESE+T pinout MAX3095ESE+T datasheet pdf MAX3095ESE+T equivalent MAX3095ESE+T replacement MAX3095ESE+T cross reference MAX3095ESE+T drop-in replacement MAX3095ESE+T vs MAX3096ESE+T MAX3095ESE+T 16-SOIC receiver MAX3095ESE+T 10Mbps RS-485 MAX3095ESE+T 3V 5V MAX3095ESE+T ESD protection MAX3095ESE+T industrial interface Analog Devices MAX3095ESE+T MAX3095ESE+T price and stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices Maxim Integrated MAX3095ESE+T MAX3095 MAX3096 MAX3096ESE+T MAX3096CSE+T MAX3095CSE+T MAX3095ESE+ RS-422 RS-485 RS-423 quad differential line receiver interface IC bus transceiver communications IC level translator ESD protection IEC 1000-4-2 air-gap discharge contact discharge 10Mbps data rate 3V supply 5V supply 16-pin SOIC narrow SOIC surface-mount package industrial automation telecommunications equipment 26LS32 differential signaling common-mode rejection
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ