MAX3243EIRHBRG4 - 500kbps RS-232 Transceiver | Texas Instruments
MPN: MAX3243EIRHBRG4 ✓ چالاکMAX3243EIRHBRG4 گشتی
An RS-232 transceiver is an interface integrated circuit that converts logic-level signals into RS-232 line levels and converts received RS-232 signals back into logic levels. Within the interface hierarchy, the MAX3243E combines a line driver, line receiver, and charge-pump voltage converter to support the bipolar voltage swings required by TIA/EIA-232-F on systems powered from a single 3 V to 5.5 V supply.
The MAX3243E family includes 3-to-5.5 V operation, a 500kbps maximum data rate, and enhanced electrostatic-discharge protection. According to the manufacturer product information, serial-port pins provide plus-or-minus 15kV HBM and IEC61000-4-2 air-gap discharge protection, plus plus-or-minus 8kV IEC61000-4-2 contact-discharge protection. These ratings are important when the interface connects to externally accessible equipment through an unprotected cable.
Internally, the dual charge-pump circuit generates the positive and negative voltages used by the line drivers, allowing the device to operate from a single low-voltage supply without an external negative supply. Three line drivers and five line receivers support common RS-232 serial-port arrangements where more receive channels are useful for handshake, status, or control signals. The receiver architecture is intended for asynchronous communication-controller interfaces operating at rates up to 500kbps.
Typical applications include industrial serial links, data-acquisition equipment, barcode and point-of-sale systems, test instrumentation, and embedded control systems. It is also suitable for equipment implementing RS-232 over cable runs where surge and electrostatic-discharge exposure is likely. System designers should still retain appropriate board-level grounding, cable routing, and chassis-protection practices because the IC ratings address specified ESD test conditions rather than every possible surge event.
The primary design consideration is decoupling. Place the charge-pump capacitors and supply capacitors close to their designated pins, keep the exposed-pad thermal and electrical connection correctly implemented, and follow the manufacturer layout guidance. Confirm that the selected connector, cable, and system grounding strategy produce compatible RS-232 levels before releasing a production design. This page combines manufacturer specifications, package details, replacement guidance, comparison data, and practical implementation notes for faster engineering evaluation.
جێگرەوەکانی جێگۆڕکێ بۆ MAX3243EIRHBRG4 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3243EIRHBRG4 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Mounting Type, Supply Voltage Range, Charge Pump.
MAX3243EIRHBR
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →ISL3241EIRZ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MAX3243EIRHBRG4 تایبەتمەندییەکان
| Product Type | Multichannel RS-232 line driver/receiver transceiver |
| Supply Voltage Range | 3 V to 5.5 V |
| Maximum Data Rate | 500kbps |
| Number of Drivers | 3 |
| Number of Receivers | 5 |
| HBM ESD Protection | ±15kV |
| IEC61000-4-2 Air-Gap ESD Protection | ±15kV |
| IEC61000-4-2 Contact ESD Protection | ±8kV |
| مەودای پلەی گەرمیی کارکردن | -40 °C to 85 °C |
| پاکێج | 32-pin VQFN (HVQCCN), 5 mm × 5 mm |
| Package Code | HVQCCN |
| Terminal Count | 32 terminals |
| جۆری دامەزراندن | No-lead surface mount |
| Package Shape | Square |
| Charge Pump | Dual charge-pump circuit |
| External Charge-Pump Capacitors | 4 capacitors |
| RS-232 Standard Compliance | TIA/EIA-232-F |
ڕێنمایی ڕێکخستنی پینی MAX3243EIRHBRG4 square
ڕێکخستنی پین بۆ MAX3243EIRHBRG4 (پاکێجی square). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3243EIRHBRG4.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MAX3243EIRHBRG4 گونجاوە بۆ 6 بەکارھێنانs: Industrial Serial Communication, Data-Acquisition Equipment, Point-of-Sale and Barcode Systems, Test and Measurement Instruments, Embedded Control Systems, Legacy Equipment Upgrade.
Industrial Serial Communication
The MAX3243EIRHBRG4 is suitable for industrial controllers that exchange asynchronous RS-232 data with test equipment, service consoles, or legacy production machinery. Its 500kbps maximum data rate provides ample bandwidth for command traffic and status polling, while the 3 V to 5.5 V supply range allows operation from common industrial logic rails. Three drivers support primary data and handshake outputs, and five receivers can accommodate multiple control signals. The specified plus-or-minus 15kV HBM and IEC61000-4-2 air-gap protection improve robustness at connector-exposed interfaces, although proper grounding and cable design remain required.
پێشنیارکراو
Data-Acquisition Equipment
The MAX3243EIRHBRG4 can connect a data-acquisition controller to RS-232 instruments that use a legacy serial interface. The three drivers and five receivers provide enough channels for command, measurement, status, and handshake signaling, while the integrated dual charge pump avoids a separate negative supply. A 500kbps data rate supports responsive command-and-response operation. In bench and laboratory equipment, the integrated ESD protection is valuable because users routinely attach external cables. Designers should still use a suitable connector, maintain defined signal-ground relationships, and verify that cable length and capacitive loading remain compatible with the operating data rate.
پێشنیارکراو
Point-of-Sale and Barcode Systems
The MAX3243EIRHBRG4 fits point-of-sale terminals, barcode readers, and peripheral controllers that communicate over RS-232. Its 500kbps capability is more than sufficient for typical command and receipt traffic, while the five receivers can support multiple peripheral-control inputs. Operation from a single 3 V to 5.5 V rail simplifies integration with embedded control hardware. The specified contact and air-gap ESD protection is particularly relevant to retail equipment where interface cables are frequently connected and disconnected. A production design should retain protective fusing or coordination where required and route the external serial traces away from sensitive analog sections.
پێشنیارکراو
Test and Measurement Instruments
پێشنیارکراو
Embedded Control Systems
The MAX3243EIRHBRG4 can provide the physical layer between a low-voltage embedded processor and an RS-232 peripheral. Its 32-VQFN package supports compact controller boards, and the single-supply charge-pump architecture avoids generating a negative rail at the system level. Five receivers offer additional control-channel capacity around the three principal driver outputs. The 500kbps ceiling is suitable for many embedded logging, configuration, and diagnostic links. Firmware and hardware designers should define logic levels, handshake polarity, and timeout behavior consistently with the connected equipment, then validate the complete path using the intended cable and connector arrangement.
پێشنیارکراو
Legacy Equipment Upgrade
The MAX3243EIRHBRG4 is useful when modernizing equipment that must retain an RS-232 connection for backward compatibility. It combines three drivers, five receivers, and an integrated dual charge pump in one compact package, reducing the need for separate level-shifting and negative-supply circuitry. The 500kbps rate supports many legacy asynchronous protocols, while the 3 V to 5.5 V range permits direct connection to contemporary control electronics. Before redesigning an existing board, compare pin assignments and connector polarity because a shared connector does not by itself guarantee electrical compatibility between different RS-232 transceiver implementations.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MAX3243EIRHBRG4 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MAX3243EIRHBR | ISL3241EIRZ |
|---|---|---|---|
| Package | 32-pin VQFN (HVQCCN), 5 mm × 5 mm | 32-pin VQFN, 5 mm × 5 mm | 32-pin QFN, 5 mm × 5 mm |
| Brand | Texas Instruments | Texas Instruments | Renesas Electronics |
| Product Type | RS-232 line driver/receiver transceiver | RS-232 line driver/receiver transceiver | RS-232 transceiver |
جیاکەرەوە سەرەکییەکان
- Five receiver channels support additional handshake and status signals (بەراورد بەISL3241EIRZ)
- Documented 500kbps multichannel operation from a single low-voltage rail (بەراورد بەISL3241EIRZ)
- Defined ESD protection on externally accessible serial-port pins (بەراورد بەISL3241EIRZ)
تێبینییەکانی دیزاین
Place the four external charge-pump capacitors and the device supply capacitors directly beside their associated package terminals, with very short traces and a low-impedance ground return. Follow the Texas Instruments recommended land pattern for the 32-pin VQFN, including the exposed-pad connection and thermal-via arrangement. Keep the compact charge-pump loop on the IC side of the board and route the longer RS-232 traces toward the connector to minimize switching noise and ESD-current coupling into sensitive circuitry.
Do not assume that two 32-pin RS-232 transceivers are pin-compatible solely because both use a 5 mm square package. Compare pin 1 orientation, supply pins, ground pins, charge-pump capacitor terminals, driver outputs, receiver inputs, shutdown behavior, and exposed-pad connections before approving a substitute. Also verify that receiver inputs tolerate unused-line conditions and that unused drivers are terminated according to the selected manufacturer’s guidance.
Treat the RS-232 cable side as an electrically harsh environment even when the IC has specified ESD protection. Use a connector with suitable mechanical retention, route the cable away from precision analog and high-speed digital circuits, and establish a deliberate signal-ground strategy between the board and connected equipment. ESD ratings demonstrate protection under defined test conditions; they do not remove the need for cable management, grounding, and any additional surge suppression required by the end installation.
Provide a stable 3 V to 5.5 V supply with local high-frequency bypassing and verify startup behavior across the complete operating range. The integrated dual charge pump creates the bipolar voltages required by the drivers, so its four external capacitors must have suitable voltage ratings, effective capacitance, low ESR, and short placement. Check capacitor tolerance and temperature characteristics against the manufacturer charge-pump requirements because incorrect capacitor selection can alter output voltage and line-driver performance.
زانیاری پابەندبوون
The component meets TIA/EIA-232-F according to Texas Instruments product information. Separate RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations were not identified in the referenced technical information.