Analog Devices

MAX3381EEUP+ 2Tx/2Rx RS-232 Transceiver | Analog Devices

MPN: MAX3381EEUP+ ✓ چالاک
+2.35 V to +5.5 V Vdss 1 uA Id EIA/TIA-232, V.28, and V.24 Rds(on) 20-pin TSSOP Package
MOQ: 1 |

MAX3381EEUP+ گشتی

Analog Devices MAX3381EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver designed for +2.35 V to +5.5 V operation, with 1 uA supply current, 460 kbps data rate, and ±15 kV ESD protection on its I/O and logic pins. The device is packaged in a 20-pin TSSOP.

An RS-232 transceiver is an interface IC that converts between single-ended logic-level signals and differential bipolar RS-232 signals. It belongs to the transceiver and line-driver hierarchy within interface ICs, allowing equipment with TTL or CMOS logic ports to communicate with RS-232 equipment over a wired serial link. The MAX3381E combines two transmit channels, two receive channels, level translation, and electrostatic-discharge protection in one package.

The MAX3381EEUP+ supports supply voltages from +2.35 V to +5.5 V, making it suitable for systems that cannot provide a conventional +5 V rail. Its 460 kbps maximum signaling rate handles common point-to-point serial-control links, while its 1 uA supply current supports low-power equipment. The ±15 kV ESD rating applies to both the RS-232 I/O pins and the logic pins.

The MAX3381E family implements powered EIA/TIA-232 and V.28/V.24 communication interfaces. Powered operation means the device includes the charge-pump circuitry required to generate the bipolar voltage levels used by RS-232. This integration reduces the external discrete components normally needed around separate line drivers and receivers, although charge-pump capacitors and interface filtering still require careful PCB planning.

Typical uses include industrial control consoles, laboratory instruments, data-acquisition equipment, point-of-sale terminals, and service-port adapters. The two transmitter and two receiver channels suit links requiring two serial paths, while the broad supply-voltage range supports both 3.3 V and 5 V system logic. Cable routing and connector selection remain important because RS-232 is designed for point-to-point communication rather than long multipoint networks.

For a new layout, place the device close to the protected connector and route each RS-232 line directly toward its connector pin with a short path. Keep logic-side traces away from the unprotected connector side of the interface. Confirm the device's enable, shutdown, receiver-output, and driver-input states during startup so that unused channels do not create bus contention.

This product record combines the manufacturer's MAX3381E family information with package, interface, speed, power, and ESD characteristics for engineering selection. It also provides verified same-package replacement context, practical layout guidance, and application-oriented comparisons that support faster component evaluation before schematic capture.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3381EEUP+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3381EEUP+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Mounting Type, Package, Communication Standard, Interface Standard, Logic Pin ESD Protection.

Analog Devices
Mounting Type: Surface mount
Communication Standard: V.28/V.24
Interface Standard: EIA/TIA-232
بەراوردکردن لەگەڵ MAX3381EEUP+ →
Analog Devices
Mounting Type: Surface mount
Package: 20-TSSOP
Communication Standard: EIA/TIA-232
بەراوردکردن لەگەڵ MAX3381EEUP+ →

MAX3381ECUP+

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 20-pin TSSOP
RS-232 transceiver · 2 · 2 · +2.35 V to +5.5 V · 1 A · EIA/TIA-232 · V.28/V.24 · 15 kV

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3381EEUP+ تایبەتمەندییەکان

Product Type RS-232 transceiver interface IC
Transmitter Channels 2 transmitters
Receiver Channels 2 receivers
Supply Voltage Range +2.35 V to +5.5 V
ئێستای دابینکردن 1 uA
Maximum Data Rate 460 kbps
RS-232 I/O ESD Protection ±15 kV
Logic Pin ESD Protection ±15 kV
Supported Communication Standards EIA/TIA-232, V.28, and V.24
پاکێج 20-pin TSSOP
جۆری دامەزراندن Surface-mount TSSOP
Signal Interface Single-ended logic to bipolar RS-232
ESD Protection Coverage RS-232 I/O pins and logic pins

ڕێنمایی ڕێکخستنی پینی MAX3381EEUP+ 20-pin tssop

ڕێکخستنی پین بۆ MAX3381EEUP+ (پاکێجی 20-pin tssop). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 20-pin tssop بۆ MAX3381EEUP+

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3381EEUP+.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3381EEUP+ گونجاوە بۆ 6 بەکارھێنانs: Industrial Control Console, Laboratory Instrument Interface, Point-of-Sale Terminal, Data-Acquisition Equipment, Service-Port Adapter, Embedded Equipment Communication.

🏭

Industrial Control Console

The MAX3381EEUP+ fits a console that needs two RS-232 output paths and two input paths on a compact controller board. Its two transmitters can drive separate service or instrument ports, while its two receivers can accept status and command channels. The +2.35 V to +5.5 V supply range accommodates 3.3 V or 5 V logic environments, and the 460 kbps rate supports common point-to-point console traffic. The ±15 kV protected RS-232 and logic pins add useful robustness, although external protection and correct grounding remain necessary at exposed connectors.

🔧

Laboratory Instrument Interface

The MAX3381EEUP+ is suitable for laboratory instruments that expose legacy RS-232 ports while running modern low-voltage control electronics. Two transmit and two receive channels support command output, data capture, and status reporting without requiring four separate interface packages. Its 460 kbps maximum rate supports instrument data links, and its broad +2.35 V to +5.5 V supply range simplifies compatibility with mixed-voltage systems. Place the transceiver near the connector, maintain a controlled ground path, and verify the instrument protocol's baud rate and handshake timing.

📱

Point-of-Sale Terminal

A point-of-sale terminal can use the MAX3381EEUP+ for two serial peripherals, such as a printer and a customer display, when both use RS-232. The integrated transmitters and receivers reduce the number of interface components, while the 20-pin TSSOP supports space-constrained board layouts. The device's 460 kbps capability is more than adequate for typical peripheral traffic, and its 1 uA supply current supports low-power operating strategies. Keep the protected interface side away from sensitive logic routing and use chassis-ground strategy appropriate to the installation environment.

🖥️

Data-Acquisition Equipment

The MAX3381EEUP+ suits data-acquisition equipment that must connect a controller to two RS-232 instruments or subsystems. One pair of channels can carry commands and the other pair can carry synchronized measurements, subject to the devices' protocol timing. Its 460 kbps signaling rate supports moderate-rate acquisition links, while the +2.35 V to +5.5 V operating range allows use with modern sensor and controller rails. Use the manufacturer's charge-pump capacitance and layout recommendations, and avoid placing long unprotected traces between the transceiver and connector.

💻

Service-Port Adapter

The MAX3381EEUP+ is appropriate for a compact service-port adapter that bridges low-voltage logic to two RS-232 service interfaces. Its 1 uA supply current and operation down to +2.35 V help when the adapter is powered from a restricted system rail, while the 20-pin TSSOP reduces board area. The 460 kbps maximum rate is suitable for configuration and firmware-service links. Designers should verify logic levels, connector pin assignments, and enable states, and should route transient-prone RS-232 traces directly toward the connector with a short return path.

🧩

Embedded Equipment Communication

The MAX3381EEUP+ can add legacy RS-232 connectivity to embedded equipment that otherwise uses low-voltage serial logic. Two transmitters and two receivers support bidirectional communication with more than one peripheral, while the broad supply range permits operation near 3.3 V systems. Its 460 kbps rate covers many control and diagnostic protocols, and the integrated powered interface removes the need for discrete charge-pump circuitry. Ensure unused outputs are disabled during reset and follow the manufacturer's grounding and decoupling layout to prevent coupling into adjacent embedded circuitry.

What is the MAX3381EEUP+?
The MAX3381EEUP+ is a 2-transmitter, 2-receiver RS-232 transceiver IC with a +2.35 V to +5.5 V supply range, 1 uA supply current, and a 460 kbps maximum data rate. According to the Analog Devices MAX3381E product information, it provides powered EIA/TIA-232 and V.28/V.24 interfaces in a 20-pin TSSOP, with ±15 kV ESD protection on both RS-232 I/O and logic pins.
What are the key specifications of MAX3381EEUP+ that engineers should know?
The key MAX3381EEUP+ specifications are two transmitters, two receivers, a +2.35 V to +5.5 V operating supply, 1 uA supply current, 460 kbps signaling capability, and ±15 kV ESD protection. Analog Devices identifies the device as a powered EIA/TIA-232 and V.28/V.24 interface in a 20-pin TSSOP, making it suitable for compact dual-channel serial-interface designs.
What supply voltage does MAX3381EEUP+ require?
The MAX3381EEUP+ operates from +2.35 V to +5.5 V. According to the Analog Devices MAX3381E family description, this range supports both 3.3 V and 5 V system environments while generating the bipolar voltage levels required by RS-232. The permitted supply range is important when determining the regulator headroom, bypass-capacitor selection, and logic compatibility of the host circuit.
What is the maximum data rate of MAX3381EEUP+?
The MAX3381EEUP+ supports data rates up to 460 kbps. This figure comes from the MAX3381E datasheet information for the powered EIA/TIA-232 and V.28/V.24 interface family. It is suitable for high-speed service ports, point-to-point control links, and instrument communication, although cable length, capacitance, grounding, and driver loading can still limit practical performance.
Does MAX3381EEUP+ provide ESD protection?
Yes, the MAX3381EEUP+ provides ±15 kV ESD protection on its RS-232 I/O pins and logic pins. Analog Devices describes this enhanced electrostatic-discharge protection as applying on both sides of the interface. The rating protects the transceiver's sensitive pins but does not replace correct connector grounding, cable design, and an appropriate external surge-protection strategy.
Where can I download the MAX3381EEUP+ datasheet PDF?
The official MAX3381E documentation is available from the Analog Devices product page at https://www.analog.com/en/products/max3381e.html. Use the manufacturer's datasheet and product-information links for the authoritative pin description, electrical characteristics, recommended charge-pump capacitors, and operating limits. The MAX3381EEUP+ ordering code includes the +2.35 V to +5.5 V 20-pin TSSOP configuration.
Where can I find the MAX3381EEUP+ pinout?
The MAX3381EEUP+ pinout is shown in the pin-description section of the manufacturer's MAX3381E documentation. Because the exact package drawing must also be matched to the 20-pin TSSOP footprint, assign PCB nets directly from that pin-description table and verify the package drawing, exposed thermal information, and land pattern. Do not infer connections solely from a generic RS-232 transceiver diagram.
Where can I buy MAX3381EEUP+ online?
The MAX3381EEUP+ can be requested through XAIPART's Request a Quote form on this page. The form is the appropriate route for current commercial availability, lot handling, packaging requirements, and delivery planning. The exact MAX3381EEUP+ ordering code should be entered when requesting a quotation so that the 20-pin TSSOP configuration is not confused with another MAX3381 family variant.
What is the price of MAX3381EEUP+?
The current commercial terms for the MAX3381EEUP+ are available through XAIPART's Request a Quote form on this page. Use that form for a quantity-specific quotation that reflects the requested order quantity, packing option, and delivery schedule. The part number identifies a 2-transmitter, 2-receiver RS-232 transceiver in a 20-pin TSSOP with a +2.35 V to +5.5 V supply range.
What is the lead time for MAX3381EEUP+?
The current lead time for MAX3381EEUP+ should be requested through XAIPART's Request a Quote form on this page. Include the required quantity, approved source condition, date code preference, and shipment destination when requesting the quotation. Because lead time can change with inventory and order configuration, engineers should plan the request before committing the production schedule.
Is MAX3381EEUP+ in stock?
Current MAX3381EEUP+ stock and allocation status should be confirmed through XAIPART's Request a Quote form on this page. Provide the quantity and required delivery date so the response reflects the actual order plan. The device is an Analog Devices 2Tx/2Rx RS-232 transceiver in a 20-pin TSSOP with a +2.35 V to +5.5 V operating supply.
What can replace MAX3381EEUP+?
The closest documented same-family replacement is the MAX3381ECUP+, which appears in the manufacturer-family cross-reference material and retains the MAX3381E 2Tx/2Rx RS-232 architecture in the same 20-pin TSSOP format. Final substitution still requires checking the C-suffix temperature grade, enable and shutdown behavior, and every electrical limit against the finished design before releasing the change.
Is MAX3381EEUP+ the same as MAX3381ECUP+?
The MAX3381EEUP+ and MAX3381ECUP+ belong to the same MAX3381E 2Tx/2Rx RS-232 interface family and use the same 20-pin TSSOP package, but their ordering suffixes identify different variants. According to Analog Devices family information, the principal family functions remain powered EIA/TIA-232 and V.28/V.24 communication with ±15 kV ESD protection. Confirm the grade-specific temperature and qualification requirements before treating one as an exact replacement.
MAX3381EEUP+ vs MAX3381ECUP+ - which is better for an industrial controller?
Choose the MAX3381EEUP+ or MAX3381ECUP+ according to the required temperature grade rather than basic interface performance. Both provide two transmitters, two receivers, operation from +2.35 V to +5.5 V, 460 kbps data rate, and ±15 kV ESD protection in a 20-pin TSSOP. For an industrial controller, verify the controller's ambient-temperature envelope and the suffix-specific limits in the manufacturer documentation.
When should I choose MAX3381EEUP+ over another RS-232 transceiver?
Choose the MAX3381EEUP+ when the design needs two RS-232 transmit channels, two receive channels, operation from +2.35 V to +5.5 V, and a 460 kbps-capable interface in a 20-pin TSSOP. Its 1 uA supply current also suits power-constrained equipment. Consider alternatives only when their channel count, voltage range, speed, shutdown behavior, package, and ESD requirements all match the system constraints.
What is the best Analog Devices equivalent for MAX3381EEUP+?
The best documented Analog Devices-family equivalent is the MAX3381ECUP+, because it uses the same MAX3381E 2Tx/2Rx RS-232 function and 20-pin TSSOP package. The substitution remains conditional on the suffix-specific temperature grade and qualification requirements. Review the manufacturer's ordering information and pin descriptions, then compare every operating limit before approving the cross-reference.

داتای سەرچاوەی ئەندازیاری بۆ MAX3381EEUP+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the MAX3381EEUP+ for a design requiring two RS-232 transmitters, two receivers, a +2.35 V to +5.5 V supply range, and data rates up to 460 kbps in a 20-pin TSSOP. Its 1 uA supply current is advantageous in power-constrained equipment, while integrated ±15 kV ESD protection improves robustness at both the connector-facing and logic-facing pins. The MAX3381ECUP+ is the documented same-family alternative for engineers needing a different ordering suffix or grade; compare its suffix-specific temperature and qualification limits before substitution. Do not choose a one-transmitter, one-receiver, or different-package RS-232 device as a direct drop-in replacement. Also verify charge-pump capacitance, enable behavior, connector mapping, and the manufacturer's grounding guidance before layout release.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3381ECUP+
Package 20-pin TSSOP 20-pin TSSOP
Brand Analog Devices Analog Devices
Transmitter Channels 2 transmitters 2 transmitters
Receiver Channels 2 receivers 2 receivers
Supply Voltage Range +2.35 V to +5.5 V +2.35 V to +5.5 V
Supply Current 1 uA 1 uA
Maximum Data Rate 460 kbps 460 kbps
RS-232 I/O ESD Protection ±15 kV ±15 kV
Communication Interfaces EIA/TIA-232, V.28, and V.24 EIA/TIA-232, V.28, and V.24
Grade-Specific Suffix E suffix in MAX3381EEUP+ C suffix in MAX3381ECUP+

جیاکەرەوە سەرەکییەکان

  • Combines four channels in one 20-pin TSSOP (بەراورد بەMAX3381ECUP+)
  • Operates across a broad low-voltage supply range (بەراورد بەMAX3381ECUP+)
  • Provides high-speed communication with integrated transient protection (بەراورد بەMAX3381ECUP+)

تێبینییەکانی دیزاین

Route the RS-232 side directly toward the connector and keep the logic side away from those traces. Place the transceiver close to the connector so transient energy has a short path to the protected pins. Use the manufacturer's pin-description and layout guidance to assign every net, and verify the 20-pin TSSOP land pattern mechanically before releasing artwork.

Use the charge-pump capacitors and bypass capacitors specified by the manufacturer for the MAX3381E family, and place them close to their associated pins. The device operates from +2.35 V to +5.5 V, so the upstream regulator must maintain the required voltage during startup and transient events. Confirm startup, enable, and shutdown states so no receiver output or transmitter output creates an unintended bus condition.

Do not treat ±15 kV ESD protection as a complete lightning or surge solution. External protection, chassis or signal-ground strategy, cable routing, and connector selection determine how much energy reaches the transceiver. Also verify that the host logic voltage matches the MAX3381E interface requirements and that every unused channel is held in a defined state during reset and power-down.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The MAX3381EEUP+ is an interface IC; no AEC-Q100 qualification is indicated. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses require confirmation from the current manufacturer product documentation or declaration.

داتا پشتڕاستکراوەتەوە لە: 2026-11-09 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3381EEUP+ datasheet MAX3381EEUP+ pinout MAX3381EEUP+ datasheet pdf MAX3381EEUP+ equivalent MAX3381EEUP+ replacement MAX3381EEUP+ cross reference MAX3381EEUP+ vs MAX3381ECUP+ MAX3381EEUP+ 460kbps MAX3381EEUP+ 20-TSSOP MAX3381EEUP+ RS-232 interface Analog Devices MAX3381EEUP+ MAX3381EEUP+ price MAX3381EEUP+ stock MAX3381EEUP+ industrial controller

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices MAX3381EEUP+ MAX3381ECUP+ MAX3381E RS-232 transceiver interface IC transceiver line driver line receiver EIA/TIA-232 V.28 V.24 TTL logic CMOS logic charge-pump interface ESD protection output noise supply voltage data rate 20-pin TSSOP TSSOP package family surface-mount package industrial control data acquisition point-of-sale terminal
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ