Analog Devices

MAX3483ECPA+ - 12Mbps RS-485 Transceiver | Analog Devices

MPN: MAX3483ECPA+ ✓ چالاک
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin PDIP through-hole package Package
MOQ: 1 |

MAX3483ECPA+ گشتی

Analog Devices MAX3483ECPA+ is a 3.3 V-powered, half-duplex RS-485/RS-422 transceiver with one driver and one receiver, a maximum data rate of 12Mbps, and ±15kV ESD protection in an 8-pin PDIP package. It combines a slew-rate-limited transmitter with a low-power receiver for robust point-to-point and multidrop serial communication.

An RS-485 transceiver is an interface IC that converts logic-level signals into differential bus voltages and reconstructs logic-level data from a differential pair. RS-485 belongs to the broader hierarchy of interface ICs, serial-interface transceivers, and communication semiconductors. The MAX3483ECPA+ can operate as both an RS-485 and an RS-422 transceiver, making it suitable for industrial control, instrumentation, and other reliable wired-data links.

The principal operating features include a 3.3 V supply, 12Mbps maximum signaling speed, ±15kV ESD protection, and slew-rate-limited RS-485/RS-422 outputs. The transmitter’s controlled edge rate helps reduce electromagnetic interference and ringing on cables. The package includes one driver and one receiver, allowing a half-duplex arrangement in which a transceiver node transmits and receives on the same differential bus.

According to the MAX3483E manufacturer documentation, this is a low-power, 3.3 V device intended for industrial communication networks. Its ESD protection helps the interface withstand electrostatic discharge encountered during installation and handling. The receiver operates from the same 3.3 V supply as the transmitter, simplifying power architecture in systems that use modern low-voltage digital logic. The slew-rate-limited driver is particularly useful when long cables, imperfect terminations, or multiple connected nodes create reflection-prone conditions.

Typical applications include industrial sensor networks, programmable-logic-controller communication links, instrumentation equipment, data-acquisition systems, and isolated or non-isolated supervisory control links. The MAX3483ECPA+ is also appropriate for embedded systems that require a legacy-compatible 8-pin through-hole footprint and a 3.3 V RS-485 interface.

When designing around the MAX3483ECPA+, account for bus-direction control, termination at the physical ends of the differential pair, and common-mode behavior across the installed cable. A transceiver with a 12Mbps capability is not automatically required to operate at that rate; lower signaling rates can improve margin in noisy or poorly terminated installations.

This product guide combines the manufacturer’s device description, package and interface characteristics, drop-in replacement assessment, comparison parameters, and practical integration guidance to support faster component selection and PCB-level planning.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3483ECPA+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3483ECPA+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Driver Count, ESD Protection, Maximum Data Rate, Package, Product Type.

Analog Devices
Driver Count: 1
Package: 8-pin PDIP
Product Type: RS-485/RS-422 transceiver
بەراوردکردن لەگەڵ MAX3483ECPA+ →
Maxim Integrated
ESD Protection: ±15 kV
Maximum Data Rate: 12 Mbps
Package: 8-PDIP (8-pin plastic DIP, through-hole)
بەراوردکردن لەگەڵ MAX3483ECPA+ →

MAX3483EEPA+

✅ جێگرەوەی ڕاستەوخۆ
Maxim Integrated
📦 8-pin PDIP
RS-485 / RS-422 · 1 driver / 1 receiver · Half-duplex · 3.0 V to 3.6 V · 12 Mbps · ±15 kV · 50 mV · Slew-rate limited (EMI controlled)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3483ECPA

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin PDIP
Same MAX3483E transceiver family and 3.3 V RS-485/RS-422 function; legacy ordering designation differs from MAX3483ECPA+ only by the trailing plus-character packaging/order suffix.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3483ECPA+ تایبەتمەندییەکان

Product Type Half-duplex RS-485/RS-422 transceiver
ڤۆڵتیەی دابینکردن 3.3 V
Operating Supply Range 3 V to 3.6 V
Maximum Data Rate 12Mbps
ESD Protection ±15kV
Driver Count 1 driver
Receiver Count 1 receiver
Supported Standards RS-485 and RS-422
Duplex Mode Half-duplex
Driver Edge Rate Slew-rate limited
Package Type 8-pin PDIP through-hole package
Total Pin Count 8 pins
Production Status Production
Datasheet Revision Revision 2

ڕێنمایی ڕێکخستنی پینی MAX3483ECPA+ 8-pin pdip through-hole package

ڕێکخستنی پین بۆ MAX3483ECPA+ (پاکێجی 8-pin pdip through-hole package). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pin pdip through-hole package بۆ MAX3483ECPA+

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3483ECPA+.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3483ECPA+ گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Networking, PLC and Data-Acquisition Links, Building and HVAC Equipment, Instrumentation and Test Equipment, Robotics and Embedded Control, Telecommunications Support Equipment.

🏭

Industrial Sensor Networking

The MAX3483ECPA+ fits industrial sensor nodes that exchange measurements over a shared RS-485 bus because it combines one driver, one receiver, a 3.3 V supply, and ±15kV ESD protection in an 8-pin PDIP footprint. Its 12Mbps capability allows a factory network to support fast polling while still permitting lower rates on noisy cable runs. Install termination only at the physical bus ends and control the transceiver direction so that only one sensor drives the pair at a time.

🖥️

PLC and Data-Acquisition Links

The MAX3483ECPA+ is appropriate for programmable-logic-controller and data-acquisition equipment that uses a 3.3 V controller to communicate over a differential RS-485 network. The half-duplex architecture minimizes wiring by sharing one driver and receiver, while the 12Mbps rating provides ample link-rate headroom. Direction control should be driven by the controller, and the bus should be tested with the actual cable length, node count, and termination arrangement.

🏭

Building and HVAC Equipment

The MAX3483ECPA+ can connect environmental controllers, HVAC modules, and supervisory equipment that exchange commands over RS-485. A 3.3 V transceiver operation is useful for modern controller boards, and ±15kV ESD protection improves interface robustness in equipment that may be installed or serviced in electrically noisy environments. The 8-pin PDIP package also supports legacy-style through-hole assembly. Firmware must arbitrate bus direction to prevent simultaneous transmission.

🔧

Instrumentation and Test Equipment

The MAX3483ECPA+ suits laboratory and field instrumentation that must exchange commands and measurement data with a remote computer or controller. The differential RS-485 interface reduces susceptibility to common-mode noise relative to single-ended signaling, while the slew-rate-limited transmitter helps control edge energy. Its 12Mbps capability supports short, high-speed laboratory links, although operators should use the slowest stable rate for long cable runs. Bus termination remains essential on longer installations.

🤖

Robotics and Embedded Control

The MAX3483ECPA+ can serve as the communication interface between a 3.3 V embedded controller and a robot subassembly, actuator node, or service computer. Its half-duplex operation reduces connector pins, and the maximum 12Mbps rate is suitable for command traffic over short wiring runs. Keep the transceiver ground reference compatible with the connected equipment, use controlled driver-enable timing, and add a termination resistor when the topology and cable require it.

🌐

Telecommunications Support Equipment

The MAX3483ECPA+ is suitable for low-power support modules that use RS-422 or RS-485 for alarm, status, and configuration messaging. The 3.3 V supply operation allows direct interfacing with modern digital logic, while the 8-pin PDIP package supports straightforward through-hole assembly and repair. The ±15kV ESD rating adds useful protection at an externally accessible interface. Confirm common-mode voltage limits and grounding strategy for each attached equipment group before deployment.

What is the MAX3483ECPA+?
The MAX3483ECPA+ is a 3.3 V-powered, half-duplex RS-485/RS-422 transceiver containing one driver and one receiver in an 8-pin PDIP package. According to the Analog Devices MAX3483E datasheet, it supports signaling up to 12Mbps and provides ±15kV ESD protection. The device is intended for differential industrial communication links where a low-voltage transceiver and through-hole package simplify replacement of an existing RS-485 interface.
What is the operating voltage of MAX3483ECPA+?
The MAX3483ECPA+ operates from a 3.3 V supply, with a documented operating range of 3 V to 3.6 V. According to the MAX3483E manufacturer datasheet, this supply arrangement allows the transceiver to share a 3.3 V rail with low-voltage digital logic. Designers should account for local supply tolerances and decoupling requirements when using the device with switching supplies or long PCB traces.
What is the maximum data rate of MAX3483ECPA+?
The MAX3483ECPA+ supports a maximum data rate of 12Mbps. This figure comes from the Analog Devices MAX3483E product documentation and the manufacturer datasheet listing. The maximum theoretical signaling rate should not be confused with a guaranteed application rate; cable length, topology, termination, clock tolerance, and signal-loss margin can require operation at a substantially lower rate.
Where can I download the MAX3483ECPA+ datasheet PDF?
The authoritative MAX3483ECPA+ documentation is available from Analog Devices through its MAX3483 product page, which links the current data sheet and supporting material. The device family is documented in the MAX3483E data sheet at Revision 2. Use that document to verify the complete pin description, electrical characteristics, timing information, and recommended transceiver application circuit before releasing a PCB.
Where can I find the MAX3483ECPA+ pinout?
The MAX3483ECPA+ uses an 8-pin PDIP through-hole package, and its complete pin assignment is defined by the pin-description table in the Analog Devices MAX3483E datasheet. Use that table when assigning driver input, receiver output, enable control, supply, ground, and differential bus connections. The summarized distributor material confirms the 8-pin package but does not provide a complete numbered pin map.
What can replace the MAX3483ECPA+?
MAX3483EEPA+ is the closest identified same-manufacturer alternative because it belongs to the same MAX3483E transceiver family and is listed in the 8-pin PDIP comparison data. MAX3483ECPA without the plus suffix is also a related ordering designation found in the component cross-reference material. Both candidates require final verification of temperature grade, enable logic, and all electrical limits before use as a drop-in replacement.
Is MAX3483EEPA+ the same as MAX3483ECPA+?
MAX3483EEPA+ and MAX3483ECPA+ are closely related MAX3483E-family transceivers, but their ordering suffixes can denote different operating-temperature or qualification grades. The identified cross-reference material places both in the 8-pin PDIP MAX3483E family and describes the same 3.3 V, 12Mbps, ±15kV ESD-protected RS-485/RS-422 architecture. Confirm the full ordering code and temperature range before treating them as interchangeable.
What is the best Analog Devices equivalent for MAX3483ECPA+?
The best identified Analog Devices-family equivalent is MAX3483EEPA+, subject to confirmation of its temperature grade and ordering details. It shares the MAX3483E 3.3 V, 12Mbps, slew-rate-limited, ±15kV ESD-protected RS-485/RS-422 transceiver architecture and the 8-pin PDIP footprint identified for the target. No unrelated cross-manufacturer drop-in part can be recommended solely from general similarity tables.
When should I choose MAX3483ECPA+ over MAX3483EEPA+?
Choose MAX3483ECPA+ when its specified operating-temperature grade matches the equipment being supported and the 8-pin PDIP footprint fits the existing PCB. Consider MAX3483EEPA+ when that ordering option has the required temperature coverage while retaining the same MAX3483E transceiver architecture. The deciding factors should be the complete ordering table, temperature range, qualification requirements, and any lifecycle notices, not merely the shared package.
Is MAX3483ECPA+ suitable for industrial RS-485 networks?
The MAX3483ECPA+ is suitable for many industrial RS-485 links because it provides differential RS-485/RS-422 operation, slew-rate-limited edges, ±15kV ESD protection, and operation from a 3.3 V supply. Its 12Mbps capability supports high-speed links, although industrial deployments may run at lower rates for better noise immunity. The final design must also satisfy bus topology, termination, grounding, and isolation requirements.
Does MAX3483ECPA+ need external termination resistors?
The MAX3483ECPA+ does not include a complete external bus-termination network in its 8-pin package. Standard RS-485 practice places termination at the two physical ends of the bus, with the exact resistor value and placement determined by the cable and topology. For short or low-speed links, the network may differ, so follow the recommended application circuit and validate reflections at the intended data rate.
How should MAX3483ECPA+ be used in a half-duplex link?
The MAX3483ECPA+ uses one driver and one receiver for a half-duplex bus arrangement, allowing a node to transmit and receive through the same differential pair. The host or controller must control driver enable so that two nodes do not drive the bus simultaneously. Because this is a non-isolated 3.3 V interface, grounding and common-mode voltage must be checked against the complete transceiver electrical limits.
Does MAX3483ECPA+ require a 5 V supply?
No. The MAX3483ECPA+ is a 3.3 V-powered device with an operating range of 3 V to 3.6 V, according to the MAX3483E manufacturer documentation. A 5 V rail is not required. Use a suitably decoupled 3.3 V source and connect the transceiver supply and ground pins according to the recommended application circuit.
Where can I buy MAX3483ECPA+ and check its lead time?
Use the Request a Quote form on this page to request the current MAX3483ECPA+ price, stock position, lead time, and order quantity from XAIPART. The public component listings confirm the exact MAX3483ECPA+ ordering designation and identify an 8-pin PDIP package, but a live quotation is required to establish current availability and delivery terms. Include your target quantity and required shipment date in the request.
What are the key specifications engineers should know about MAX3483ECPA+?
The key MAX3483ECPA+ specifications are a 3.3 V operating supply, 12Mbps maximum data rate, ±15kV ESD protection, one driver, one receiver, half-duplex operation, slew-rate-limited RS-485/RS-422 outputs, and an 8-pin PDIP package. These characteristics place it among low-voltage, high-speed differential interface ICs. Exact receiver thresholds, common-mode limits, supply current, and temperature range must be taken from the manufacturer data sheet before final design signoff.

داتای سەرچاوەی ئەندازیاری بۆ MAX3483ECPA+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose MAX3483ECPA+ when the design requires a 3.3 V, half-duplex RS-485/RS-422 interface with one driver, one receiver, ±15kV ESD protection, and an 8-pin PDIP footprint. MAX3483EEPA+ is a closely related family alternative when its ordering table provides the required operating-temperature grade; confirm enable behavior, limits, and lifecycle status before substitution. MAX3483ECPA is another identified legacy ordering designation with the same core MAX3483E architecture, but the trailing plus-character difference requires procurement and assembly review. No cross-brand drop-in replacement has been established because the available cross-reference results do not document a candidate with both the same 8-pin PDIP pinout and verified electrical compatibility. For designs using SOIC, select the appropriate surface-mount family member instead of attempting a package conversion.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3483EEPA+ MAX3483ECPA
Brand Analog Devices Analog Devices Analog Devices
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP
Product Type Half-duplex RS-485/RS-422 transceiver Half-duplex RS-485/RS-422 transceiver Half-duplex RS-485/RS-422 transceiver
Supply Voltage 3.3 V 3.3 V 3.3 V
Operating Supply Range 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V
Maximum Data Rate 12Mbps 12Mbps 12Mbps
ESD Protection ±15kV ±15kV ±15kV
Driver and Receiver Count 1 driver and 1 receiver 1 driver and 1 receiver 1 driver and 1 receiver
Driver Edge Control Slew-rate limited Slew-rate limited Slew-rate limited

جیاکەرەوە سەرەکییەکان

  • High-speed 3.3 V differential interface in a through-hole package (بەراورد بەMAX3483ECPA)
  • Slew-rate-limited driver reduces cable-edge energy (بەراورد بەMAX3483ECPA)
  • Integrated high-energy ESD protection (بەراورد بەMAX3483EEPA+)

تێبینییەکانی دیزاین

Place the MAX3483ECPA+ close to the RS-485 connector and route the A and B differential pair as a tightly coupled, continuous trace. Avoid introducing stubs to test points or unused transceiver nodes. Provide local supply decoupling and a solid ground reference, but keep the connector-side transient-energy path away from sensitive logic so that surge and ESD currents do not flow through the digital ground area.

Do not enable the driver while another node is transmitting. Firmware or hardware should provide a defined direction-control sequence and allow the bus to return to receive mode before another node responds. On long or noisy cables, operation well below the 12Mbps maximum can improve reflection and noise-margin behavior. Confirm termination, biasing, cable length, and topology as a complete bus rather than validating only one transceiver.

Use the MAX3483E pin-description table when assigning the 8-pin PDIP footprint and verify enable polarity in the final schematic. Place any bus termination components near the physical line interface so that switching energy is dissipated close to the connector. Maintain controlled return current beneath the differential pair, avoid sharing narrow ground paths with switching converters, and keep the transceiver away from high-current switching nodes where possible.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The MAX3483 product page identifies the device as being in production, but the accessible product summaries do not state specific RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification results. AEC-Q100 is marked not applicable because the target is not identified as an automotive-qualified variant.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3483ECPA+ datasheet MAX3483ECPA+ specifications MAX3483ECPA+ pinout MAX3483ECPA+ datasheet pdf MAX3483ECPA+ equivalent MAX3483ECPA+ replacement MAX3483ECPA+ cross reference MAX3483ECPA+ vs MAX3483EEPA+ Analog Devices MAX3483ECPA+ MAX3483ECPA+ PDIP RS-485 MAX3483ECPA+ 12Mbps transceiver MAX3483ECPA+ industrial application MAX3483ECPA+ price MAX3483ECPA+ stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices MAX3483ECPA+ MAX3483EEPA+ MAX3483ECPA MAX3483E RS-485 transceiver RS-422 transceiver half-duplex transceiver interface IC serial-interface transceiver communication semiconductor differential signaling slew-rate-limited driver ESD protection 3.3 V power supply 12Mbps data rate PDIP-8 package through-hole package industrial automation sensor network programmable logic controller data acquisition EMI common-mode voltage
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ