Analog Devices

MAX3483ESA+T - 3.3V RS-485/RS-422 Transceiver | ADI

MPN: MAX3483ESA+T ✓ چالاک
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-SOIC, 8 pins Package
MOQ: 1 |

MAX3483ESA+T گشتی

Analog Devices MAX3483ESA+T is a 3.3 V powered RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 10 Mbps, and an 8-SOIC package. The MAX3483 family combines a true RS-485/RS-422 driver, receiver, and slew-rate-limited driver in a compact surface-mount package.

An RS-485/RS-422 transceiver is a physical-layer interface IC that converts logic-level signals into differential bus voltages and converts received differential signals back into logic levels. It belongs to the transceiver hierarchy: differential line driver and receiver, communications interface IC, interface semiconductor. True differential signaling improves noise immunity over single-ended links and supports reliable communication across industrial, instrumentation, and control environments.

The MAX3483ESA+T operates from a 3.3 V supply and supports data rates up to 10 Mbps. Its slew-rate-limited driver reduces electromagnetic interference and helps limit reflections on improperly terminated cables. The manufacturer documentation also describes operation up to 250 kbps for the MAX3483ESA, so system designers should verify the speed grade and timing limits relevant to their cable, topology, and termination arrangement.

The device contains one driver and one receiver, supporting half-duplex RS-485 operation when the driver-enable and receiver-enable controls are used together. Driver and receiver outputs can be placed in a high-impedance state when disabled. This control flexibility supports shared multidrop buses, direction control from a host controller, and designs that keep the receiver active while the driver is inactive.

Typical uses include industrial RS-485 links, RS-422 point-to-point communications, building-control equipment, instrumentation networks, data-acquisition systems, and embedded control systems. The 3.3 V supply aligns with modern controller I/O levels, while the differential bus interface supports communication over cables that would be unreliable with ordinary single-ended logic.

A successful design must select the proper cable length, data rate, topology, biasing, and termination. Place the transceiver close to the connector, route the differential pair as a tightly coupled pair, provide a continuous ground reference where appropriate, and avoid stubs that create impedance discontinuities. Confirm the logic polarity and timing of DE and RE before connecting the device to a multidrop network.

This page combines the manufacturer product information, distributor listings, package information, comparison data, and practical RS-485 design guidance. It also identifies pin-compatible family alternatives and highlights the functional trade-offs that matter when selecting a transceiver for a new or existing board.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3483ESA+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3483ESA+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Driver Type, Maximum Data Rate, Supported Standards, Driver Count.

Analog Devices
Package: 8-SOIC
Driver Type: Slew-rate-limited true RS-485/RS-422 driver
Maximum Data Rate: 12 Mbps
بەراوردکردن لەگەڵ MAX3483ESA+T →
Analog Devices
Package: 8-pin NSOIC
Driver Type: Slew-rate-limited true driver
Maximum Data Rate: 12 Mbps
بەراوردکردن لەگەڵ MAX3483ESA+T →
Analog Devices
Package: 8-SOIC
Supported Standards: RS-422 and RS-485
Driver Count: 1
بەراوردکردن لەگەڵ MAX3483ESA+T →

MAX3483ECSA+T

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-SOIC
RS-485/RS-422 transceiver · 1 transmitter and 1 receiver · Half duplex · 3.0 V to 3.6 V · 12 Mbps · ±15 kV · Slew-rate-limited true RS-485/RS-422 driver · RS-485 and RS-422

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3483EESA

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC
Uses the E temperature-grade suffix in the same 8-SOIC footprint; exact speed and temperature limits must be checked against MAX3483ESA+T.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3483ESA+

✅ جێگرەوەی ڕاستەوخۆ
Maxim Integrated
📦 8-SOIC
RS-485/RS-422 transceiver · 3.3 V · 3 V to 3.6 V · 10 Mbps · 1 driver and 1 receiver · Half-duplex · RS-485 and RS-422 · Slew-rate limited

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3440EASA+T

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC
Documented as a related 8-SOIC replacement candidate; maximum data rate and supply current require confirmation because MAX3483ESA+T is specified up to 10 Mbps.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3441EASA

✅ جێگرەوەی ڕاستەوخۆ
📦 8-SOIC
Documented as a related 8-SOIC replacement candidate; speed, supply current, and enable timing must be confirmed against the MAX3483ESA+T design limits.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX3483ESA+T تایبەتمەندییەکان

Product Type RS-485/RS-422 transceiver
ڤۆڵتیەی دابینکردن 3.3 V
Maximum Data Rate 10 Mbps
Documented Low-Rate Operation Up to 250 kbps
Driver Count 1 driver
Receiver Count 1 receiver
Communication Mode Half-duplex
Standards Supported RS-485 and RS-422
Driver Type Slew-rate-limited true differential driver
Disabled Output State High impedance
Controls Driver Enable and Receiver Enable
پاکێج 8-SOIC, 8 pins
جۆری دامەزراندن Surface mount

ڕێنمایی ڕێکخستنی پینی MAX3483ESA+T 8-soic, 8 pins

ڕێکخستنی پین بۆ MAX3483ESA+T (پاکێجی 8-soic, 8 pins). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-soic, 8 pins بۆ MAX3483ESA+T

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3483ESA+T.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3483ESA+T گونجاوە بۆ 6 بەکارھێنانs: Industrial RS-485 Control Bus, RS-422 Point-to-Point Link, Data-Acquisition Instrumentation, Building and HVAC Controls, Embedded Serial Communication Port, Low-Speed RS-485 Sensor Network.

🏭

Industrial RS-485 Control Bus

The MAX3483ESA+T fits a 3.3 V industrial controller that must communicate over a differential RS-485 bus with one transceiver per node. Its one-driver, one-receiver arrangement supports half-duplex operation, while DE and RE permit the controller to switch bus direction. The manufacturer rates the MAX3483 family for operation up to 10 Mbps and describes the MAX3483ESA for transmission up to 250 kbps. Slew-rate-limited drive helps reduce EMI and cable reflections, although the final baud rate must be validated against cable length, topology, termination, and propagation delay.

🌐

RS-422 Point-to-Point Link

For a point-to-point RS-422 connection, the MAX3483ESA+T provides a 3.3 V differential driver and receiver in an 8-SOIC package. The architecture allows the receiver to remain enabled while the driver is disabled, which can simplify asynchronous link management and diagnostics. With operation listed up to 10 Mbps for the family and a 250 kbps figure in MAX3483ESA documentation, designers should select the intended speed grade and confirm timing margin. Proper source termination remains important when preserving signal integrity at the receiver.

📊

Data-Acquisition Instrumentation

The MAX3483ESA+T can connect a 3.3 V data-acquisition controller to remote sensors or instrument modules over RS-485. Differential signaling improves noise tolerance on factory-floor cables, while the slew-rate-limited driver helps control high-frequency emissions. The device's one-driver, one-receiver arrangement is well suited to bus nodes that alternate between transmitting commands and receiving measurements. Engineers should use shielded twisted-pair cabling, maintain a continuous ground reference where permitted, and test the complete system at the intended distance because baud rate, termination, and topology determine reliable reach.

🏠

Building and HVAC Controls

The MAX3483ESA+T is appropriate for a 3.3 V building-control node that exchanges sensor readings and actuator commands over an RS-485 backbone. Its compact 8-SOIC package preserves PCB area, and DE and RE provide the directional control required by a shared bus. The manufacturer's 3.3 V operating point supports integration with embedded controllers, while slew-rate-limited drive reduces EMI in equipment containing clocks, relays, and switching power stages. Deployment planning should account for bus termination at physical endpoints, biasing for an idle network, and isolation where ground-potential differences are possible.

🖥️

Embedded Serial Communication Port

The MAX3483ESA+T can provide a dedicated differential port on a 3.3 V embedded controller that already generates serial transmit and receive logic. One transceiver handles both directions and exposes DE and RE for firmware-controlled bus arbitration or echo management. Operation up to 10 Mbps is useful for short, well-terminated links, whereas the 250 kbps MAX3483ESA figure provides a conservative reference for longer cables. Firmware must avoid driving the bus while another node transmits, and the hardware design must prevent enabled-driver conflicts through careful DE timing and pull-state design.

🧩

Low-Speed RS-485 Sensor Network

For low-speed sensor networks, the MAX3483ESA+T combines a 3.3 V differential interface, slew-rate limiting, and DE/RE bus-direction control in an 8-SOIC package. The documented MAX3483ESA operation up to 250 kbps is suitable as a conservative design target for modest cable lengths and distributed nodes. Low communication speed increases available timing margin and can simplify termination and transceiver selection. The network still needs correct bias resistors, termination only at the cable endpoints, a shared ground reference, and firmware that coordinates a single active driver to prevent bus contention.

What are the key specifications of MAX3483ESA+T that engineers should know?
The MAX3483ESA+T is a 3.3 V powered, half-duplex RS-485/RS-422 transceiver with one driver, one receiver, operation up to 10 Mbps, slew-rate-limited drive, and an 8-SOIC package. According to the Analog Devices MAX3483 data sheet and manufacturer product page, it supports true differential communications, DE and RE control pins, and high-impedance disabled outputs. These characteristics make it suitable for industrial control, instrumentation, and embedded systems using 3.3 V logic.
What is the operating voltage of MAX3483ESA+T?
The MAX3483ESA+T operates from a 3.3 V supply. Analog Devices describes the MAX3483 as a 3.3 V powered, low-power RS-485/RS-422 communications transceiver. This supply voltage allows direct interface with many 3.3 V microcontrollers and programmable controllers, but the entire system must still meet the device's input thresholds, output levels, and absolute maximum ratings listed in the manufacturer data sheet.
What is the maximum data rate of MAX3483ESA+T?
The MAX3483ESA+T supports a maximum data rate of 10 Mbps according to the Analog Devices MAX3483 product page. Manufacturer documentation also describes the MAX3483ESA as providing error-free data transmission at rates up to 250 kbps. Cable length, topology, termination, and propagation delay can reduce practical margin, so the operating limit should be validated with the intended bus configuration.
Where can I download the MAX3483ESA+T datasheet PDF?
The official MAX3483 documentation is available from the Analog Devices product page at https://www.analog.com/en/products/MAX3483.html. Select the data sheet link associated with the MAX3483 family, then confirm that the ordering information includes MAX3483ESA+T and its 8-SOIC package. The manufacturer data sheet is the controlling document for pin descriptions, electrical limits, timing, and recommended application circuits.
Where can I find the MAX3483ESA+T pinout?
The MAX3483ESA+T pin assignments are shown in the pin-description and package-drawing sections of the Analog Devices MAX3483 data sheet. The device uses an 8-SOIC package with pins for supply, ground, driver input and enable, driver differential output, receiver input, receiver enable, and receiver output. Assign PCB nets from the manufacturer pin-description table rather than inferring connections from a generic RS-485 diagram.
Is MAX3483ESA+T suitable for industrial RS-485 equipment?
The MAX3483ESA+T is suitable for many 3.3 V industrial RS-485 and RS-422 interfaces because it provides true differential I/O, slew-rate-limited drive, DE and RE controls, and operation up to 10 Mbps. For a finished industrial product, additional system requirements such as surge immunity, isolation, temperature range, and regulatory testing must be evaluated separately because they are not established solely by the transceiver specification.
What can replace MAX3483ESA+T on the same PCB?
The closest documented same-footprint options include MAX3483ECSA+T, MAX3483EESA, MAX3440EASA+T, and MAX3441EASA, but each must be checked for speed, ESD rating, supply current, and enable-control behavior before substitution. MAX3483ECSA+T is the most direct option because the comparison identifies it as a 3.3 V, slew-rate-limited, true RS-485/RS-422 transceiver in an 8-SOIC package.
What is the best Analog Devices equivalent for MAX3483ESA+T?
MAX3483ECSA+T is the best documented Analog Devices equivalent for MAX3483ESA+T because it is identified as an ESD-protected, 3.3 V powered, slew-rate-limited true RS-485/RS-422 transceiver in an 8-SOIC package. Pin compatibility alone does not guarantee equivalence: verify the exact ESD rating, data-rate limit, supply current, and operating-temperature grade before approving a substitution.
MAX3483ESA+T vs MAX3440EASA+T - which is better for a 3.3 V bus?
MAX3483ESA+T is the better documented choice when a design requires the MAX3483 family's 10 Mbps class operation, true RS-485/RS-422 operation, and slew-rate-limited drive. MAX3440EASA+T appears in the comparison data as a potential replacement, but its speed and electrical ratings should be checked against the 10 Mbps target. Both use an 8-pin SOIC form factor, so package compatibility does not by itself establish circuit equivalence.
MAX3483ESA+T vs MAX3483EESA - what is the difference?
MAX3483EESA is a distinct suffix option rather than a simple identical replacement for MAX3483ESA+T. The manufacturer lists MAX3483E as a 3.3 V, slew-rate-limited RS-485/RS-422 transceiver family, while MAX3483ECSA+T is specifically described as ESD protected. Before using MAX3483EESA, verify its exact speed, ESD rating, temperature grade, and lifecycle status against the design requirements.
When should I choose MAX3483ESA+T over MAX3441EASA?
Choose MAX3483ESA+T when the design is already qualified around the MAX3483 family's documented 10 Mbps operation and its DE/RE control behavior. The comparison data identifies MAX3441EASA as a related replacement candidate, but its maximum data rate, supply current, ESD protection, and timing must be confirmed before use. MAX3441EASA is appropriate only when its electrical limits fully satisfy the original design.
Is MAX3483ESA+T the same as MAX3483ECSA+T?
No. MAX3483ECSA+T has an explicit C suffix associated with ESD protection, while MAX3483ESA+T does not identify that enhanced suffix. The MAX3483ECSA+T comparison describes an 8-SOIC, 3.3 V, slew-rate-limited true RS-485/RS-422 transceiver, but upgrading to it can alter protection characteristics and regulatory design assumptions. Confirm the exact suffix and compare the manufacturer data sheets.
Where to buy MAX3483ESA+T online?
Use the Request a Quote form on this page to request MAX3483ESA+T availability, current commercial terms, and a lead-time quotation for the exact 8-SOIC ordering code. The manufacturer lists MAX3483 production status, and distributor listings identify MAX3483ESA+T, but stock and lead time can change independently of lifecycle status. Submit the exact suffix MAX3483ESA+T with your required quantity.
What is the price of MAX3483ESA+T?
The current price of MAX3483ESA+T is not stated in a form suitable for static publication on this page. Use the Request a Quote form on this page and provide the required quantity, delivery location, and target date. The manufacturer product page shows a starting list price for the product family, but that family-level figure does not establish the commercial price for the exact MAX3483ESA+T suffix.
What is the lead time and stock status for MAX3483ESA+T?
Use the Request a Quote form on this page for the current MAX3483ESA+T stock position, production allocation, and lead time. Analog Devices identifies the MAX3483 family as production, and distributor listings show the exact ordering code, but those facts do not guarantee immediate inventory for every quantity. State the required reel quantity and delivery schedule in the quotation request.

داتای سەرچاوەی ئەندازیاری بۆ MAX3483ESA+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose MAX3483ESA+T for a new 3.3 V RS-485 or RS-422 interface when the design requires a compact 8-SOIC transceiver, one driver, one receiver, DE/RE direction control, and operation up to 10 Mbps. MAX3483ECSA+T is the preferred alternative when the additional ESD-protection suffix is relevant, provided its exact protection rating satisfies the system requirement. MAX3483EESA should be considered when its 12 Mbps listing and temperature grade align with the design. MAX3440EASA+T and MAX3441EASA require closer electrical review because the same package does not guarantee identical speed, supply current, timing, or protection. For long cables or large installations, favor a lower, validated baud rate, proper endpoint termination, adequate biasing, and a continuous ground reference rather than selecting solely by package.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3483ECSA+T MAX3483EESA MAX3483ESA MAX3440EASA+T MAX3441EASA
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC

جیاکەرەوە سەرەکییەکان

  • Higher documented speed capability than the low-rate MAX3483ESA description (بەراورد بەMAX3440EASA+T)
  • Clear manufacturer documentation for the original device family (بەراورد بەMAX3441EASA)
  • Direct same-family footprint with a documented enhanced-protection option (بەراورد بەMAX3483ECSA+T)

تێبینییەکانی دیزاین

Place the MAX3483ESA+T close to the board connector and preserve a continuous differential pair for the bus traces. Route A and B together with matched geometry, avoid routing over plane splits, and keep the driver and receiver return path continuous. Place optional termination and protection components near the connector so that surge current is diverted before reaching the transceiver. Confirm the connector and transceiver ground arrangement against the interface's common-mode and isolation requirements.

Termination must match the cable impedance and should normally be applied at the physical endpoints of a multidrop bus, not at every node. Biasing is also needed when the bus must remain in a defined idle state, but the resistor values and topology should follow the manufacturer application guidance for the intended topology. For a 10 Mbps-class link, control stubs, connector transitions, and connector lead geometry because they can create reflections even when the cable itself is properly terminated.

Do not enable more than one driver on a shared RS-485 bus. Firmware should keep DE deasserted while receiving, coordinate bus access, and avoid changing direction before the transmitter output is electrically inactive. Treat the manufacturer's 10 Mbps family rating and the 250 kbps MAX3483ESA documentation as different design constraints: verify which speed rating applies to the exact suffix and validate the complete bus at the intended distance before production.

The slew-rate-limited driver reduces high-frequency edge energy, but EMI performance still depends on cable type, common-mode voltage, connector shielding, and the surrounding system. Use twisted-pair wiring, maintain a suitable ground reference, and avoid long unprotected stubs. If the transceiver is mounted near switching regulators, relays, or high-current power stages, place the interface toward the connector and separate it from noisy return currents to reduce differential and common-mode coupling.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The manufacturer lists the MAX3483 family as production. Exact RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status for MAX3483ESA+T were not established from the product information and must be confirmed before regulatory release.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3483ESA+T datasheet MAX3483ESA+T pinout MAX3483ESA+T datasheet pdf MAX3483ESA+T equivalent MAX3483ESA+T replacement MAX3483ESA+T vs MAX3483ECSA+T MAX3483ESA+T vs MAX3440EASA+T Analog Devices MAX3483ESA+T MAX3483ESA+T 8-SOIC transceiver MAX3483ESA+T RS-485 application circuit MAX3483ESA+T price MAX3483ESA+T stock MAX3483 3.3V 10Mbps transceiver MAX3483ESA+T RS-422 interface

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices MAX3483ESA+T MAX3483 MAX3483E MAX3483ECSA+T MAX3440EASA+T MAX3441EASA RS-485 RS-422 differential transceiver half-duplex transceiver line driver line receiver slew-rate-limited driver Driver Enable Receiver Enable high-impedance output 3.3 V power supply 10 Mbps data rate 250 kbps operation 8-SOIC package SOIC family surface-mount package industrial control building automation
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ