Analog Devices

MAX3488ECSA+ - 12Mbps RS-485/RS-422 Transceiver | Analog Devices

MPN: MAX3488ECSA+ ✓ چالاک
3.3 V Vdss RS-485 and RS-422 Rds(on) 8-pin NSOIC Package
MOQ: 1 |

MAX3488ECSA+ گشتی

The Analog Devices MAX3488ECSA+ is a 3.3 V RS-485/RS-422 transceiver with a maximum data rate of 12 Mbps, ±15 kV ESD protection, and an 8-pin NSOIC package. The device combines one driver and one receiver, while its slew-rate-limited driver reduces electromagnetic interference and reflections associated with improperly terminated cables. These characteristics make it suitable for industrial instrumentation, building controls, data acquisition, and noise-sensitive serial communication systems.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level digital signals into balanced differential signals and receives differential signals back as logic-level data. The MAX3488ECSA+ belongs to the transceiver hierarchy alongside RS-485 and RS-422 interface ICs, where balanced signaling improves noise immunity and allows communication over longer cables than a single-ended interface. Its true transceiver architecture supports half-duplex or point-to-point differential communication when configured correctly in the target system.

The principal features include operation from a 3.3 V supply, ±15 kV ESD protection on the communication pins, a maximum signaling rate of 12 Mbps, and slew-rate-limited operation. The low-power design is intended to reduce system power consumption while retaining the bandwidth needed for industrial and control networks. The MAX3488 family is specifically identified by Analog Devices as a production family, indicating that the MAX3488ECSA+ remains part of the active product line.

Slew-rate limiting is the key electrical feature for robust field-bus communication. By controlling the driver edge rate, the MAX3488ECSA+ reduces high-frequency EMI and lowers the likelihood of signal reflections on imperfectly terminated cables. The 12 Mbps maximum data rate supports high-speed data links, although actual bus length, cable impedance, topology, termination, and transceiver enable timing can limit the usable rate in a practical installation.

Typical uses include industrial automation controllers, PLC serial interfaces, sensor and actuator networks, building-management equipment, and isolated or non-isolated data-acquisition systems. The device can also connect MCU-based control boards to differential bus nodes when its driver and receiver pins, enable controls, grounding, and termination are assigned according to the manufacturer's pin and application guidance.

A critical implementation consideration is bus termination. Place the correct termination network at the physical ends of the RS-485 or RS-422 bus, and keep the driver disabled while the receiver is active unless the network architecture explicitly supports both functions simultaneously. Validate signal polarity and enable timing to prevent contention on the driver outputs.

This product page combines the manufacturer's core electrical specifications, practical interface guidance, application use cases, and confirmed pin-compatible alternatives. It also highlights the differences that matter when reviewing a MAX3488ECSA+ replacement for an existing 8-pin NSOIC circuit-board layout.

جێگرەوەکانی جێگۆڕکێ بۆ MAX3488ECSA+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX3488ECSA+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Maximum Data Rate, Mounting Type, Driver Count, Receiver Count.

Analog Devices
Package: 8-pin PDIP
Mounting Type: Through-hole
بەراوردکردن لەگەڵ MAX3488ECSA+ →
Maxim Integrated
Driver Count: 1
Receiver Count: 1
بەراوردکردن لەگەڵ MAX3488ECSA+ →
Maxim Integrated
Package: 8-SOIC
Maximum Data Rate: 10 Mbps
بەراوردکردن لەگەڵ MAX3488ECSA+ →

MAX3488EESA+

✅ جێگرەوەی ڕاستەوخۆ
Maxim Integrated
📦 8-pin NSOIC
RS-485/RS-422 transceiver · 3.3 V · 12 Mbps · ±15 kV · 1 · 1 · True differential RS-485/RS-422 · Slew-rate limited

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3488ECPA+

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-pin NSOIC
3.3 V · 12 Mbps · ±15 kV · RS-422/RS-485 · 1 transmitter and 1 receiver · Slew-rate-limited true RS-485/RS-422 · Differential RS-422/RS-485 receiver · 8-pin PDIP

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX3488ECSA+ تایبەتمەندییەکان

ڤۆڵتیەی دابینکردن 3.3 V
Operating Supply Voltage Range 3 V to 3.6 V
Maximum Data Rate 12 Mbps
ESD Protection ±15 kV
Driver Count 1 driver
Receiver Count 1 receiver
Communication Standards RS-485 and RS-422
Driver Architecture Slew-rate-limited true transceiver
Signal Type Balanced differential
پاکێج 8-pin NSOIC
جۆری دامەزراندن Surface mount
Power Classification Low-power device

ڕێنمایی ڕێکخستنی پینی MAX3488ECSA+ 8-pin nsoic

ڕێکخستنی پین بۆ MAX3488ECSA+ (پاکێجی 8-pin nsoic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pin nsoic بۆ MAX3488ECSA+

هیچ داتای وردی پینئاوت بەردەست نییە بۆ MAX3488ECSA+.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

MAX3488ECSA+ گونجاوە بۆ 6 بەکارھێنانs: Industrial Automation Serial Buses, Building Automation Networks, Data Acquisition Equipment, Instrumentation and Sensor Networks, Communications Equipment, Motor and Power Control Systems.

🏭

Industrial Automation Serial Buses

The MAX3488ECSA+ fits industrial control and automation links that require differential signaling at up to 12 Mbps. Its 3.3 V supply integrates directly with modern controller logic, while the slew-rate-limited driver reduces EMI and reflections associated with imperfect cable termination. The ±15 kV ESD rating also strengthens the interface against electrostatic discharge encountered around equipment connectors. In a PLC or controller, the device can translate MCU-level serial commands to an RS-485 field bus and receive field-bus responses. Validate bus topology, common-mode limits, grounding, and termination so the 12 Mbps capability translates into reliable operation at the installed cable length.

🧩

Building Automation Networks

The MAX3488ECSA+ is appropriate for building-management equipment that connects controllers, sensors, and actuators over an RS-485 network. Balanced differential signaling improves noise immunity in buildings containing motor drives, lighting equipment, and switching power supplies. The device's 3.3 V operation supports low-voltage embedded controllers, while slew-rate limiting helps control high-frequency emissions from long inter-floor cable runs. A building controller can use the transceiver for request-and-response polling of distributed sensors. The actual supported rate depends on cable length, baud rate, topology, and termination, so use the manufacturer's interface guidance when calculating propagation delay and reflection margins.

🖥️

Data Acquisition Equipment

The MAX3488ECSA+ can connect laboratory and industrial data-acquisition modules to a differential RS-485 or RS-422 controller. Its 12 Mbps maximum rate provides bandwidth for synchronized measurements, configuration downloads, and status reporting, while the receiver and driver operate from the same 3.3 V rail used by many modern acquisition modules. The slew-rate-limited output helps preserve signal quality on imperfectly terminated test leads. In a multi-instrument installation, assign unique bus addresses and control driver enable timing to prevent multiple drivers from driving the bus simultaneously. Verify the receiver's common-mode range against the installed grounding arrangement.

📡

Instrumentation and Sensor Networks

The MAX3488ECSA+ suits instrumentation networks that distribute measurements from remote sensors over balanced RS-485 or RS-422 links. Differential communication reduces susceptibility to common-mode noise, while the integrated ±15 kV ESD protection improves robustness near connector and service points. The 3.3 V supply allows the transceiver to operate beside low-voltage sensors and embedded controllers. Place the device according to the manufacturer's pin configuration, then use a termination network at the cable endpoints and bias resistors only where the bus architecture requires them. At long distances, reduce the data rate to the level supported by propagation delay, cable loss, and the measured noise environment.

🌐

Communications Equipment

The MAX3488ECSA+ is useful in communications equipment that adds a robust differential port to a 3.3 V controller. Its 12 Mbps capability accommodates high-speed data transfer, while the slew-rate-limited driver reduces edge energy that can create EMI in compact enclosures. The transceiver can support a point-to-point RS-422 connection or an RS-485 multidrop bus when termination and enable logic are configured correctly. In a communications appliance, keep the differential traces away from switching nodes and use a solid ground reference. Confirm that the external protection strategy handles sustained surge or lightning conditions because ESD protection alone is not a substitute for a correctly designed surge-protection network.

⚡

Motor and Power Control Systems

The MAX3488ECSA+ can connect a motor-control or power-control board to external diagnostics, programming equipment, and remote monitoring nodes through an RS-485 or RS-422 interface. Differential signaling is useful in environments containing high-current switching stages and long cable runs, while slew-rate limiting helps reduce conducted emissions. The 3.3 V interface matches many embedded motor controllers, and ±15 kV ESD protection adds defense at exposed communication connectors. The transceiver should remain separated from high-energy switching paths, and designers should assess common-mode voltage, isolated power, and chassis-ground requirements. Termination and biasing must be calculated for the actual bus rather than copied between different cable lengths.

What is the MAX3488ECSA+?
The MAX3488ECSA+ is a 3.3 V, half-duplex RS-485/RS-422 interface transceiver containing one driver and one receiver in an 8-pin NSOIC package. According to the Analog Devices MAX3488E manufacturer datasheet, it supports signaling rates up to 12 Mbps and provides ±15 kV ESD protection. Its slew-rate-limited driver is intended to reduce EMI and cable reflections in industrial communication networks.
What are the key specifications of MAX3488ECSA+ that engineers should know?
The key MAX3488ECSA+ specifications are a 3.3 V supply, operation from 3 V to 3.6 V, a 12 Mbps maximum data rate, ±15 kV ESD protection, one driver, one receiver, and an 8-pin NSOIC package. The Analog Devices manufacturer datasheet also identifies the device as a low-power, slew-rate-limited true RS-485/RS-422 transceiver, making it suitable for high-speed differential data links where controlled edge rates and ESD robustness are important.
Where can I download the MAX3488ECSA+ datasheet PDF?
The MAX3488ECSA+ datasheet is available through the Analog Devices MAX3488E product page, which links to the manufacturer's technical documentation for the 3.3 V, ±15 kV ESD-protected, 12 Mbps MAX3488E family. Use the MAX3488E document for the MAX3488ECSA+ pin configuration, electrical characteristics, and application guidance. The manufacturer's family page is the appropriate starting point because package and ordering-code suffixes determine the exact temperature, package, and shipping configuration.
Where is the MAX3488ECSA+ pinout located?
The MAX3488ECSA+ pinout is shown in the pin configuration section of the Analog Devices MAX3488E manufacturer datasheet. The device uses an 8-pin NSOIC package and includes receiver output, driver-enable inputs, driver input, ground, supply, and differential bus connections. Use that pin-description table when assigning PCB tracks, and follow the package drawing for pin-1 orientation because no complete pin list is reproduced on this product page.
What is the difference between MAX3488ECSA+ and MAX3488EESA+?
The MAX3488ECSA+ and MAX3488EESA+ are closely related MAX3488E-family transceivers in the same 8-pin NSOIC format, with the same fundamental role as 3.3 V, ±15 kV ESD-protected, 12 Mbps RS-485/RS-422 transceivers. Their ordering suffixes identify different manufacturer temperature-grade or configuration options. Confirm the exact grade, temperature range, and ordering code in the MAX3488E datasheet before substituting one for the other in production equipment.
Is MAX3488ECSA+ suitable for industrial RS-485 communication?
Yes, the MAX3488ECSA+ is suitable for industrial RS-485 communication because it combines a 3.3 V supply, ±15 kV ESD protection, slew-rate-limited signaling, and operation up to 12 Mbps in an 8-pin NSOIC package. According to the Analog Devices manufacturer datasheet, the slew-rate-limited driver reduces EMI and reflections from improperly terminated cables. Actual industrial suitability still depends on surge protection, grounding, isolation, and the voltage levels present at the bus connector.
When should I choose MAX3488ECSA+ over a lower-speed RS-485 transceiver?
Choose the MAX3488ECSA+ when the system needs a differential bus data rate as high as 12 Mbps or when its ±15 kV ESD-protected interface and controlled driver edge rate are required. The Analog Devices manufacturer datasheet identifies the MAX3488E family as a 3.3 V, slew-rate-limited, true RS-485/RS-422 transceiver. A lower-speed device may be preferable only when the bus is much shorter, operates at a much lower data rate, or has a lower system power requirement.
When should I choose MAX3488ECSA+ over MAX3488ECPA+?
Choose MAX3488ECSA+ when the existing PCB accepts the 8-pin NSOIC package associated with the ECSA ordering code. The MAX3488ECPA+ belongs to the same MAX3488E family but its suffix identifies a different manufacturer package option, so board outline, hole pattern, lead geometry, and pin assignment must be checked before substitution. Both parts serve the same RS-485/RS-422 transceiver role, but package interchangeability is not implied by a shared family name.
What is the best drop-in replacement for MAX3488ECSA+?
The closest confirmed drop-in choices are the MAX3488EESA+ and MAX3488ECSA+ variants that retain the same 8-pin NSOIC interface, according to comparison records for the MAX3488E family. A valid replacement must preserve the 3.3 V supply, RS-485/RS-422 transceiver function, and pin mapping while meeting the required ESD, data-rate, temperature, and sourcing requirements. Verify the exact suffix and grade before approving a production substitution.
Can MAX3488EESA+ replace MAX3488ECSA+ without PCB changes?
The MAX3488EESA+ can be considered as a pin-compatible MAX3488E-family alternative because comparison information identifies the same 8-pin NSOIC package and the same 3.3 V, ±15 kV ESD-protected, 12 Mbps transceiver architecture. No PCB artwork change is expected when its pin mapping matches the MAX3488ECSA+, but the engineer must still confirm temperature grade, enable behavior, and production requirements. Mark the replacement only after those checks are complete.
What can replace MAX3488ECSA+ on the same RS-485 board?
A board-compatible replacement for the MAX3488ECSA+ should use the same 8-pin NSOIC footprint and preserve the receiver, driver-enable, driver-input, ground, supply, and differential bus connections. MAX3488EESA+ is a documented same-family option, while the MAX3488ECSA+ tape-and-reel ordering variant is electrically identical but is not a distinct engineering alternative. Cross-brand substitutes require separate pin and parameter verification before use.
Where to buy MAX3488ECSA+ online?
Use the Request a Quote form on this page to request the MAX3488ECSA+, current availability, minimum order quantity, and delivery information. The Analog Devices product page identifies MAX3488E as a production family, and distributor records list the MAX3488ECSA+ in an 8-SOIC configuration. The quote request keeps commercial details linked to the exact ordering code rather than a family-level listing.
What is the price of MAX3488ECSA+?
Current pricing for the MAX3488ECSA+ is provided through the Request a Quote form on this page because commercial terms can change with quantity and availability. Submit the exact MPN MAX3488ECSA+, required quantity, and delivery location to obtain a current quotation. This request should preserve the correct 8-pin NSOIC ordering configuration and avoid accidental substitution of a different package or temperature suffix.
What is the lead time for MAX3488ECSA+?
The current lead time for MAX3488ECSA+ should be requested through the Request a Quote form on this page using the exact MPN and required quantity. Analog Devices lists the MAX3488E family as a production family, but production status alone does not establish current stock, manufacturing availability, or delivery timing. Include the target delivery date and acceptable packaging configuration in the request for an actionable schedule.
Is MAX3488ECSA+ in stock?
Stock status for MAX3488ECSA+ should be confirmed through the Request a Quote form on this page. The manufacturer identifies MAX3488E as a production family, while distributor listings indicate market availability, but neither fact alone guarantees inventory for every quantity and package suffix. Include the exact MPN, order quantity, and target ship date so the response reflects the precise configuration required for production.
What is the best Analog Devices equivalent for MAX3488ECSA+?
The best Analog Devices equivalent is the closest orderable MAX3488E-family configuration that retains the same 8-pin NSOIC footprint, 3.3 V supply, 12 Mbps data-rate capability, ±15 kV ESD protection, and RS-485/RS-422 transceiver function. MAX3488EESA+ is a confirmed family comparison candidate. A shared MAX3488E family designation alone does not prove that every ordering suffix has identical temperature range or package construction, so the datasheet ordering table remains controlling.

داتای سەرچاوەی ئەندازیاری بۆ MAX3488ECSA+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the MAX3488ECSA+ for a 3.3 V RS-485 or RS-422 interface that requires up to 12 Mbps, slew-rate-limited driver behavior, and ±15 kV ESD protection in an 8-pin NSOIC package. It is particularly suitable for industrial controllers, building automation, instrumentation, and data-acquisition equipment where balanced signaling helps reject common-mode noise. MAX3488EESA+ is a same-family candidate when its ordering suffix provides the required temperature grade and qualification, while MAX3488ECPA+ should be considered only after its package construction and footprint have been confirmed. Neither option should be selected merely because it shares the MAX3488E family name. Verify pin mapping, operating temperature, common-mode limits, availability, and lifecycle requirements. If the design requires galvanic isolation, sustained surge protection, or a data rate below the family's supported range, a different interface architecture may be more appropriate.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX3488EESA+ MAX3488ECPA+
Package 8-pin NSOIC 8-pin NSOIC 8-pin NSOIC
Brand Analog Devices Analog Devices Analog Devices
Supply Voltage 3.3 V 3.3 V 3.3 V
Maximum Data Rate 12 Mbps 12 Mbps 12 Mbps
ESD Protection ±15 kV ±15 kV ±15 kV
Driver and Receiver Count 1 driver and 1 receiver 1 driver and 1 receiver 1 driver and 1 receiver
Supported Interfaces RS-485 and RS-422 RS-485 and RS-422 RS-485 and RS-422
Driver Edge Control Slew-rate limited Slew-rate limited Slew-rate limited
Pin Compatibility 8-pin NSOIC reference configuration Pin-compatible on the stated NSOIC configuration Pin-compatible on the stated NSOIC configuration

جیاکەرەوە سەرەکییەکان

  • High-speed slew-rate-limited interface (بەراورد بەMAX3488EESA+)
  • Same-footprint family option with controlled edge rate (بەراورد بەMAX3488ECPA+)
  • Production-family status and focused transceiver function (بەراورد بەMAX3488EESA+)

تێبینییەکانی دیزاین

Do not enable the driver while the receiver is active unless the bus topology explicitly requires that operating state. Driver contention can increase current and distort communications. The MAX3488ECSA+ uses separate driver-enable and receiver-enable controls, so firmware and hardware should place the interface in transmit mode only while the node owns the bus. Confirm the enable polarity and timing against the Analog Devices MAX3488E manufacturer datasheet before connecting external logic.

Route the RS-485 and RS-422 differential pair as a tightly coupled pair over a continuous reference plane. Keep the pair length matched within the limits required by the installed topology, minimize stubs, and avoid routing through switching-power-supply regions. Place termination components at the physical bus endpoints rather than beside every node. The MAX3488ECSA+ can operate to 12 Mbps, so short stubs and controlled edge rates are essential at higher communication rates.

Treat cable and connector protection as a separate design layer from the transceiver's internal ESD structures. The MAX3488ECSA+ provides ±15 kV ESD protection, but that rating does not replace coordinated surge protection, chassis grounding, or isolation. Use the transceiver pin configuration and application guidance to define the protected interface boundary, and verify that external components do not degrade the intended 3.3 V signaling or introduce excessive capacitive loading.

Place the decoupling network close to the transceiver's supply and ground pins, following the capacitor value and layout specified in the manufacturer application guidance. Because the MAX3488ECSA+ operates from 3.3 V, verify that the host supply remains within the stated 3 V to 3.6 V range during startup and load transients. This is especially important when the transceiver shares a rail with switching converters whose ripple and overshoot could otherwise compromise communication reliability.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The family is identified as production by Analog Devices, but the listed manufacturer information does not explicitly establish the requested compliance statuses. Verify the exact ordering code and current manufacturer declarations before treating the device as RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals compliant.

داتا پشتڕاستکراوەتەوە لە: 2026-11-02 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX3488ECSA+ datasheet MAX3488ECSA+ pinout MAX3488ECSA+ datasheet pdf MAX3488ECSA+ equivalent MAX3488ECSA+ replacement MAX3488ECSA+ cross reference MAX3488ECSA+ vs MAX3488EESA+ MAX3488ECSA+ vs MAX3488ECPA+ MAX3488ECSA+ 12Mbps transceiver MAX3488ECSA+ NSOIC footprint MAX3488ECSA+ RS-485 interface MAX3488ECSA+ RS-422 interface Analog Devices MAX3488ECSA+ MAX3488ECSA+ price MAX3488ECSA+ stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices Maxim Integrated MAX3488ECSA+ MAX3488E MAX3488EESA+ MAX3488ECPA+ RS-485 transceiver RS-422 transceiver interface IC balanced differential signaling slew-rate-limited driver 12 Mbps data rate ±15 kV ESD protection 3.3 V power supply 8-pin NSOIC SOIC package family surface-mount package industrial automation building automation data acquisition EMI cable termination ESD protection RS-485 bus
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ