Analog Devices

MAX485ESA+T - 2.5Mbps RS-485/RS-422 Transceiver | ADI

MPN: MAX485ESA+T ✓ چالاک
4.75 V to 5.25 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
MOQ: 1 |

MAX485ESA+T گشتی

Analog Devices MAX485ESA+T is a low-power half-duplex RS-485/RS-422 interface transceiver with one driver and one receiver, a maximum data rate of 2.5Mbps, and a 4.75V to 5.25V supply range. The device is supplied in an 8-pin SOIC package and is intended for industrial bidirectional serial-data links.

An RS-485 transceiver is an interface IC that combines a differential line driver and differential receiver. These transceivers connect a host controller, PLC, sensor, or industrial endpoint to a balanced communication bus. The RS-485 standard hierarchy supports longer, noise-resistant interconnects than single-ended interfaces, while RS-422 compatibility allows the same device family to serve point-to-point links. Driver enable and receiver-enable inputs provide local control over bus direction and reception.

The MAX485ESA+T uses a 4.75V to 5.25V supply and supports data rates up to 2.5Mbps. Its driver is short-circuit-current limited and protected, an important feature when a bus fault drives a line into a low-impedance condition. The integrated receiver converts differential bus voltage into a logic-level output, while the driver converts logic-level data into differential output. This combination supports half-duplex operation, in which the same pair of conductors carries transmitted and received data at different times.

The 8-pin SOIC package keeps the implementation compact and familiar to industrial-control board designers. Because the MAX485ESA+T does not limit its slew rate, it can transmit at up to 2.5Mbps according to the provided manufacturer and distributor documentation. That speed is useful for factory automation, instrumentation, and embedded control networks, although cable length, termination, topology, and signal integrity become increasingly restrictive as data rate rises.

Typical uses include RS-485 fieldbus connections, motor-control diagnostics, industrial sensor gateways, building-control equipment, and communications between a microcontroller and remote peripheral. In a typical circuit, the transceiver sits between a UART-capable controller and a protected, twisted-pair bus. A termination resistor is placed at each end of the bus, while common-mode protection and chassis-grounding practices may be needed in electrically noisy installations.

Designers should verify that the selected cable length and topology can support the intended 2.5Mbps rate, connect the receiver and driver enables for the required half-duplex behavior, and maintain compatible logic levels across the system. The 5V supply requirement also requires a 4.75V to 5.25V regulator rather than a 3.3V rail.

This page combines the verified manufacturer and distributor information with package-level engineering guidance, practical interface considerations, pricing context, and pin-compatible replacement analysis to support faster component selection and PCB migration.

جێگرەوەکانی جێگۆڕکێ بۆ MAX485ESA+T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MAX485ESA+T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Data Rate, RoHS Status, Mounting Type, Duplex.

Analog Devices
Data Rate: Up to 2.5 Mbps
Duplex: Half-Duplex
بەراوردکردن لەگەڵ MAX485ESA+T →
Analog Devices
Package: 8-pin NSOIC/SOIC
بەراوردکردن لەگەڵ MAX485ESA+T →
Analog Devices
Package: 8-SOIC (SOIC-8)
Data Rate: 2.5 Mbps
RoHS Status: Compliant (per Maxim/ADI datasheet suffix '+')
بەراوردکردن لەگەڵ MAX485ESA+T →
Analog Devices
Package: 8-SOIC (NS)
Data Rate: 250 kbps
Duplex: Half
بەراوردکردن لەگەڵ MAX485ESA+T →
MaxLinear
Package: 8-pin NSOIC or PDIP
Data Rate: 2.5 Mbps (max, SP485E non-slew-limited)
RoHS Status: Compliant
بەراوردکردن لەگەڵ MAX485ESA+T →

MAX481ESA

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
Same 8-pin SO footprint and pin-compatible family; maximum data rate differs by up to 30% from the 2.5Mbps MAX485ESA+T rating

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX483ESA

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
Same 8-pin SO footprint and pin-compatible family; maximum data rate differs by up to 30% from the 2.5Mbps MAX485ESA+T rating

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX487ESA+

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 8-pin SOIC
Transceiver · RS-422, RS-485 · 1/1 · Half · 4.75 V to 5.25 V · 250 kbps · 120 µA to 500 µA · 0.1 µA (typical)

پەیوەندی بۆ نرخ

بینینی داتاشیت →

MAX1487ESA

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
Same 8-pin SO footprint and pin-compatible family; maximum data rate differs by up to 30% from the 2.5Mbps MAX485ESA+T rating

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SP485EN-L/TR

✅ جێگرەوەی ڕاستەوخۆ
MaxLinear
📦 8-pin SOIC
Half-duplex differential transceiver · RS-422 and RS-485 · 5 Mbps · 4.75V to 5.25V · 5 V · -40°C to +85°C · 1 differential driver and 1 differential receiver · Half-duplex

پەیوەندی بۆ نرخ

بینینی داتاشیت →

COS485ESA

✅ جێگرەوەی ڕاستەوخۆ
📦 8-pin SOIC
Direct pin-compatible replacement in the same 8-pin SO footprint; verified cross-reference describes identical MAX485-class functionality

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX485ESA+T تایبەتمەندییەکان

Product Type RS-485/RS-422 transceiver
Transceiver Configuration 1 driver and 1 receiver
Operating Mode Half-duplex
Supply Voltage Range 4.75 V to 5.25 V
Maximum Data Rate 2.5 Mbps
Slew Rate Limiting Not limited
Driver Short-Circuit Protection Current limited and protected
Supported Standards RS-485 and RS-422
پاکێج 8-pin SOIC
Package Pin Count 8 pins
جۆری دامەزراندن Surface mount
دۆخی RoHS unknown
REACH Status unknown
AEC-Q100 Qualification unknown

ڕێکخستنی پینی MAX485ESA+T

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پین 1 RO — Receiver output
پین 2 RE — Receiver enable, active low
پین 3 DE — Driver enable, active high
پین 4 DI — Driver input
پین 5 GND — Ground
پین 6 Y — Non-inverting driver output
پین 7 A — Inverting driver output
پین 8 VCC — Positive supply

بەکارهێنانە باوەکان

MAX485ESA+T گونجاوە بۆ 6 بەکارھێنانs: Industrial PLC Fieldbus Communication, Factory Sensor Gateway, Motor Control and Diagnostics, Building Control and HVAC Equipment, Instrumentation and Measurement Systems, Remote Monitoring and Environmental Telemetry.

🏭

Industrial PLC Fieldbus Communication

The MAX485ESA+T fits PLC fieldbus modules that require a 5V half-duplex differential interface at rates up to 2.5Mbps. Its integrated driver and receiver connect the controller's UART logic to a balanced industrial bus, while the protected driver helps limit fault current when a line is shorted. The 8-pin SOIC supports compact, surface-mount assembly. In a multi-drop installation, terminate both physical ends of the bus, maintain consistent reference ground, and verify that the selected cable length preserves reliable margins at the intended data rate.

🏭

Factory Sensor Gateway

The MAX485ESA+T is suitable for a factory sensor gateway that aggregates remote RS-485 measurements over a wired industrial backbone. Its 4.75V to 5.25V operating range matches conventional industrial logic systems, while the 2.5Mbps capability supports rapid polling of multiple field devices. The transceiver is placed between the gateway UART and a protected twisted-pair bus. Designers should account for bus-stub length, common-mode transients, and the timing relationship between driver enable and receiver enable during direction changes.

⚡

Motor Control and Diagnostics

The MAX485ESA+T can serve as the communication link in a motor-control module where a controller monitors drive diagnostics or exchanges commands with a remote drive. Differential RS-485 reception improves tolerance to industrial noise compared with a single-ended link, and the 2.5Mbps rate provides ample bandwidth for control and status packets. The protected driver helps contain bus faults, but the implementation still needs appropriate surge protection, grounding, and isolation strategy when the motor environment introduces high-energy transients.

🏠

Building Control and HVAC Equipment

The MAX485ESA+T is appropriate for building-control equipment that uses an RS-485 backbone for sensors, actuators, or distributed HVAC controllers. Its one-driver, one-receiver arrangement enables half-duplex communication from a common bus, and the 8-pin SOIC package fits standard controller-board layouts. For reliable building deployments, use twisted-pair cabling, place termination only at the two bus endpoints, route communications wiring away from high-current switching circuits, and validate operation across the required temperature and ground-offset conditions.

🔬

Instrumentation and Measurement Systems

The MAX485ESA+T fits laboratory and industrial instrumentation that distributes commands or collects measurements across a multi-drop RS-485 bus. Its 2.5Mbps capability shortens transaction time and supports bursts of measurement data, while the differential receiver helps preserve signal integrity in instrument racks containing switching power supplies and motors. The transceiver requires a compatible 5V supply and logic family; designers should keep analog and digital return currents separated and use calibrated termination to minimize reflections on the bus.

🌐

Remote Monitoring and Environmental Telemetry

The MAX485ESA+T can connect environmental monitors, remote sensors, and telemetry equipment over a wired RS-485 network. The 4.75V to 5.25V supply and 2.5Mbps data capability support both slow monitoring traffic and higher-rate burst updates. The transceiver is typically connected to a microcontroller UART, with the driver and receiver enables coordinated to avoid bus contention. Long outdoor cables require deliberate protection, grounding, and surge-current handling because the verified source data does not establish the device's transient withstand ratings.

کورتەی بەرهەمە پێشنیارکراوەکان

P82B96PWR Texas Instruments بەکارهێنراوە لە: Industrial PLC Fieldbus Communication P82B96DR Texas Instruments بەکارهێنراوە لە: Industrial PLC Fieldbus Communication MAX232DR Texas Instruments بەکارهێنراوە لە: Industrial PLC Fieldbus Communication ATMEGA328P-MUR Microchip Technology بەکارهێنراوە لە: Factory Sensor Gateway STM32F072RBT7TR STMicroelectronics بەکارهێنراوە لە: Factory Sensor Gateway P82B96DRG4 Texas Instruments بەکارهێنراوە لە: Factory Sensor Gateway STM32F446ZEH6TR STMicroelectronics بەکارهێنراوە لە: Motor Control and Diagnostics TMS320C10FNLR Texas Instruments بەکارهێنراوە لە: Motor Control and Diagnostics TMC2084-HT Microchip Technology بەکارهێنراوە لە: Motor Control and Diagnostics ATSAM4S2CB-AN Microchip Technology بەکارهێنراوە لە: Building Control and HVAC Equipment MSP430F5438AIPZR Texas Instruments بەکارهێنراوە لە: Building Control and HVAC Equipment ATMEGA1281-16MU Microchip Technology بەکارهێنراوە لە: Building Control and HVAC Equipment ADS? Not used because an unverified companion MPN is unavailable بەکارهێنراوە لە: Instrumentation and Measurement Systems NE5534DR Texas Instruments بەکارهێنراوە لە: Instrumentation and Measurement Systems AK4118VF Audio measurement interface companion بەکارهێنراوە لە: Instrumentation and Measurement Systems ATMEGA328P-ANR Microchip Technology بەکارهێنراوە لە: Remote Monitoring and Environmental Telemetry ATSAM3S1BB-AU Microchip Technology بەکارهێنراوە لە: Remote Monitoring and Environmental Telemetry MSP430F149IPAGR Texas Instruments بەکارهێنراوە لە: Remote Monitoring and Environmental Telemetry
What is the maximum data rate of MAX485ESA+T?
The MAX485ESA+T supports data rates up to 2.5Mbps. According to the manufacturer MAX485 datasheet and the verified distributor documentation, the device does not limit its slew rate, allowing the transmitter to operate at this maximum rate. In practice, the usable rate also depends on cable length, bus topology, termination, transceiver enable timing, and the integrity of the differential connection.
What is the operating voltage of MAX485ESA+T?
The MAX485ESA+T operates from a 4.75V to 5.25V supply. According to the verified LCSC product listing and manufacturer datasheet information, this is a 5V-class RS-485/RS-422 transceiver. It therefore cannot be powered directly from a 3.3V rail, and its external logic levels must also be compatible with the system controller.
What are the key specifications of MAX485ESA+T that engineers should know?
The MAX485ESA+T is a 4.75V to 5.25V, half-duplex RS-485/RS-422 transceiver rated up to 2.5Mbps. It contains one driver and one receiver, does not limit slew rate, and provides a short-circuit-protected driver. According to the manufacturer datasheet and verified distributor documentation, it is packaged in an 8-pin SOIC for conventional surface-mount PCB assembly.
Where to buy MAX485ESA+T online?
MAX485ESA+T is available from major electronics distributors, including DigiKey, Mouser, LCSC, and Octopart-listed suppliers. The verified LCSC listing shows a unit price of $0.5572 and 54,509 units in stock as of 2026-10-29. Distributor inventory changes continuously, so engineers should confirm the exact suffix, package, and shipment quantity before placing a production order.
What is the price of MAX485ESA+T?
The verified LCSC listing shows MAX485ESA+T from $0.5572 as of 2026-10-29. The same part is also listed by DigiKey, Mouser, and Octopart, but the supplied search data does not include a consolidated price comparison or verified volume-break pricing. Request a quotation from the selected authorized distributor when purchasing higher quantities.
What is the lead time for MAX485ESA+T?
The supplied distributor data does not state a guaranteed lead time for MAX485ESA+T. The DigiKey listing says the part ships today, while LCSC reports 54,509 units in stock, but these are availability snapshots as of 2026-10-29 rather than contractual lead-time commitments. Confirm current stock, factory lead time, and backorder status directly with the distributor for your required quantity.
Is MAX485ESA+T in stock?
Yes, the verified LCSC listing reported 54,509 MAX485ESA+T units in stock on 2026-10-29, and the DigiKey search result states that the part can ship today. Inventory is distributor-specific and can change rapidly. The amount shown is not a guarantee of XAIPART inventory, so purchasing teams should confirm availability and the exact MAX485ESA+T ordering code before committing to a schedule.
Where to download the MAX485ESA+T datasheet PDF?
The manufacturer MAX485 datasheet can be accessed through the verified MAX485ESA datasheet PDF page, which covers the MAX485 and related MAX48x transceivers. The MAX485ESA+T ordering code specifies the surface-mount 8-pin SOIC package and tape-and-reel shipment format. Designers should use the manufacturer document for definitive pinout, absolute-maximum, electrical-characteristic, and recommended-application information.
Where to find the MAX485ESA+T pinout?
The MAX485ESA+T pin configuration is shown in the manufacturer MAX485 datasheet, available from the verified MAX485ESA datasheet PDF page. The 8-pin SOIC arrangement provides receiver output, receiver enable, driver enable, driver input, ground, driver outputs, and supply. Confirm the exact pin numbers against the datasheet before assembling a PCB because enable polarity and package orientation are critical.
MAX485ESA+T vs MAX481ESA - which is better for industrial RS-485?
MAX485ESA+T is the better choice when the design requires operation up to 2.5Mbps, while MAX481ESA is a pin-compatible same-family option for lower-rate links. The verified cross-reference data identifies the MAX48x devices as pin-compatible in the 8-pin SO package. Final selection should compare maximum data rate, receiver behavior, bus loading, enable timing, and protection specifications in the manufacturer datasheets.
What is the difference between MAX485ESA+T and SP485EN-L/TR?
The MAX485ESA+T is a 2.5Mbps, 4.75V to 5.25V RS-485/RS-422 transceiver in an 8-pin SOIC, while the MaxLinear cross-reference identifies SP485EN-L/TR as a functionally equivalent, pin-compatible alternative. Verify data rate, supply range, receiver fail-safe behavior, ESD rating, and enable timing before substitution because a pin-compatible footprint does not guarantee identical electrical performance.
When should I choose MAX485ESA+T over a lower-speed drop-in alternative?
Choose MAX485ESA+T when the bus must support data rates up to 2.5Mbps and the system uses a 4.75V to 5.25V supply. According to the manufacturer datasheet, its driver is not slew-rate limited, making it appropriate for faster industrial links. Use a lower-speed equivalent only when its rated data rate, common-mode range, protection, and receiver thresholds satisfy the complete design requirements.
Is MAX485ESA+T suitable for PLC and industrial sensor networks?
The MAX485ESA+T is suitable for many PLC and industrial sensor networks requiring a 5V RS-485 or RS-422 interface at up to 2.5Mbps. Its one-driver, one-receiver half-duplex architecture, short-circuit-protected driver, and 8-pin SOIC package fit conventional industrial-control designs. The enclosure, surge protection, grounding, cable type, and isolation requirements remain system-level considerations.
What can replace MAX485ESA+T?
The verified cross-reference data supports MAX481ESA, MAX483ESA, MAX487ESA, and MAX1487ESA as pin-compatible same-family options, while also identifying SP485EN-L/TR and COS485ESA as cross-brand drop-in candidates. The best replacement depends on data rate, supply voltage, receiver fail-safe thresholds, ESD protection, bus loading, and enable timing. Review all manufacturer specifications before approving a substitution.
What is the best MaxLinear equivalent for MAX485ESA+T?
The MaxLinear cross-reference specifically identifies SP485EN-L/TR as a functional equivalent and pin-compatible substitute for MAX485ESA-T. According to that cross-reference, engineers should still compare maximum data rate, supply voltage, logic thresholds, common-mode range, ESD protection, and driver enable behavior. The provided evidence supports the cross-reference, but it does not establish identical performance for every application.

داتای سەرچاوەی ئەندازیاری بۆ MAX485ESA+T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose MAX485ESA+T for 5V RS-485 or RS-422 links that require a half-duplex transceiver capable of 2.5Mbps, especially when using the established MAX48x 8-pin SOIC footprint. Select MAX481ESA, MAX483ESA, MAX487ESA, or MAX1487ESA when their lower or application-specific data rates and electrical characteristics better match the bus, while retaining pin compatibility for PCB reuse. SP485EN-L/TR is a verified MaxLinear functional-equivalent candidate, and COS485ESA is described as a direct drop-in replacement. Before approving either cross-brand part, verify supply range, receiver thresholds, fail-safe behavior, common-mode limits, ESD rating, enable timing, and maximum data rate. The MAX485ESA+T is the appropriate baseline when its documented 2.5Mbps capability, short-circuit-protected driver, and 4.75V-to-5.25V supply range align with the design.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە MAX481ESA MAX483ESA MAX487ESA MAX1487ESA SP485EN-L/TR COS485ESA
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices MaxLinear Cosine Nanoelectronics
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485 transceiver RS-485/RS-422 transceiver

جیاکەرەوە سەرەکییەکان

  • High-speed half-duplex operation (بەراورد بەMAX481ESA)
  • No slew-rate limitation (بەراورد بەSP485EN-L/TR)
  • Protected differential driver (بەراورد بەCOS485ESA)

تێبینییەکانی دیزاین

Route the MAX485ESA+T driver and receiver connections as a closely matched differential pair. Place the bus-side protection and termination components near the transceiver or connector according to the cable interface design, and provide a short, low-impedance ground return. Keep switching-power-supply loops and high-current motor traces away from the RS-485 pair to reduce differential noise coupling and common-mode conversion.

Design the transceiver rail for 4.75V to 5.25V. Decouple the VCC pin with local high-frequency and bulk capacitance close to the device, while keeping the return current continuous. The verified source data does not state the device's supply-current limit, so calculate the regulator capacity from the manufacturer electrical characteristics before adding cable-driver load or adjacent 5V circuitry.

Do not enable the driver and receiver outputs simultaneously if multiple nodes can transmit on the same bus. Coordinate DE and /RE around the UART direction-control signal, allow the required driver and receiver settling time, and confirm that no other node begins transmitting before the previous transmission has ended. Incorrect enable polarity or timing is a common source of corrupted frames and bus contention.

Use twisted-pair cable for the differential bus and terminate only the two physical ends of the main trunk. Avoid long stub branches, particularly at the 2.5Mbps maximum rate, because reflected signals can overlap the next bit. Verify the completed cable length, topology, common-mode range, and protection scheme using the manufacturer's recommended operating conditions and appropriate test equipment.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The supplied manufacturer and distributor search results do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements for MAX485ESA+T. No compliance status was assumed.

داتا پشتڕاستکراوەتەوە لە: 2026-10-29 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

MAX485ESA+T MAX485ESA+T datasheet Analog Devices MAX485ESA+T MAX485ESA+T 2.5Mbps transceiver MAX485ESA+T 8-pin SOIC MAX485ESA+T RS-485 industrial bus MAX485ESA+T vs MAX481ESA SP485EN-L/TR equivalent for MAX485ESA+T MAX485ESA+T drop-in replacement MAX485ESA+T price where to buy MAX485ESA+T MAX485ESA+T pinout 5V half duplex RS-485 transceiver SOIC-8 MAX485ESA+T lead time and stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Analog Devices Maxim Integrated MAX485ESA+T MAX485ESA MAX481ESA MAX483ESA MAX487ESA MAX1487ESA SP485EN-L/TR COS485ESA RS-485 RS-422 half-duplex transceiver differential line driver differential receiver interface IC 8-pin SOIC SOIC package family surface-mount technology 2.5Mbps data rate 4.75V to 5.25V supply slew rate short-circuit protection industrial automation PLC communication
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ