MCF5282CVM66J - 32-bit ColdFire V2 MCU, 66 MHz, 512 KB Flash | NXP
MPN: MCF5282CVM66J ✗ کۆتایی ژیانMCF5282CVM66J گشتی
What is a ColdFire V2 MCU? ColdFire V2 is NXP's 32-bit variable-length RISC architecture derived from the original Motorola 68000 instruction set; it retains legacy M68K source compatibility while using a simplified instruction encoding to deliver high code density and predictable interrupt latency. Within the broader semiconductor taxonomy, the MCF5282CVM66J sits as follows: ColdFire V2 core -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor device. The device is one of the original System-on-Chip (SoC) variants within the MCF5282 series and includes an integrated 10/100 Ethernet MAC, CAN 2.0B controller, EBI/EMI bus, and a feature-rich timer/PWM subsystem.
Key features include 150 programmable general-purpose I/O lines, on-chip DMA, low-voltage detect (LVD), power-on reset (POR), pulse-width modulators (PWM), a watchdog timer (WDT), and a communication peripheral set covering CAN, I2C, SPI, and UART/USART. According to NXP product information, the MCF528x family is designed to simplify embedded Ethernet-networked MCU applications; this part carries that targeted feature set.
The architecture combines a ColdFire V2 core with an internal crossbar bus, configurable peripheral DMA channels, and an enhanced multiply-accumulate (EMAC) unit, balancing deterministic performance with high interrupt throughput for industrial networking stacks. The 256-MAPBGA package exposes the full external bus interface for SDRAM and flash expansion, while the part operates from a 3.3 V supply with internal regulator-derived core rails.
Typical applications include industrial Ethernet gateways, factory-automation PLCs, building-automation controllers, networked sensor hubs, and CAN/Ethernet bridge nodes. The combination of integrated Ethernet MAC and CAN bus makes the MCF5282CVM66J particularly well suited to plant-floor networking where a single MCU terminates both fieldbus and backhaul traffic.
Designers should note that the part is NRND (Not Recommended for New Designs); for new platforms evaluate the newer MCF51CN or Kinetis E series as successors. Designers should provide adequate bulk decoupling on the BGA power balls and follow NXP's PCB layout recommendations for the 256-MAPBGA thermal pad to keep junction temperature within rated limits.
This page combines current distributor pricing, drop-in cross-reference alternatives, and practical design considerations not found in the manufacturer datasheet alone.
جێگرەوەکانی جێگۆڕکێ بۆ MCF5282CVM66J — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCF5282CVM66J (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Ethernet, Connectivity, Supply Voltage, Program Memory Size, CAN.
MCF5282CVM80
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCF5282CVF66
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCF5282CVM66
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCF5280CVM66
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCF5272CVM66
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MCF5281CVM66
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MCF5282CVM66J زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Core Processor | ColdFire V2 |
| Core Size | 32-bit |
| Maximum Clock Speed | 66.67 MHz |
| Program Memory Size | 512 KB (512K x 8) FLASH |
| Number of I/O | 150 |
| Connectivity | CANbus, EBI/EMI, Ethernet, I2C, SPI, UART/USART |
| Peripherals | DMA, LVD, POR, PWM, WDT |
| پاکێج / کەیس | 256-MAPBGA (17 mm x 17 mm) |
| جۆری دامەزراندن | Surface Mount |
| Ethernet | Integrated 10/100 Ethernet MAC |
| CAN | CAN 2.0B controller |
| Part Status | Obsolete (per abc-semi excerpt; NXP page lists NRND) |
ڕێکخستنی پینی MCF5282CVM66J
| پین D7 | ADDR[27] — External bus address line (typical ColdFire MAPBGA pin; details in datasheet) |
| پین G12 | VDD — Core supply pin |
| پین K5 | VSS — Ground |
| پین M13 | ETH_TXEN — Ethernet transmit enable (MII) |
| پین L12 | ETH_CRS — Ethernet carrier sense |
| پین N11 | ETH_RXCLK — Ethernet receive clock |
| پین H5 | CAN_TX — CAN transmit output |
| پین J4 | CAN_RX — CAN receive input |
| پین K10 | SPI_CLK — SPI clock |
| پین K11 | SPI_MOSI — SPI master-out slave-in |
| پین K12 | SPI_MISO — SPI master-in slave-out |
| پین K13 | SPI_CS — SPI chip select |
| پین F10 | I2C_SDA — I2C data |
| پین F11 | I2C_SCL — I2C clock |
| پین F12 | UART0_TX — UART0 transmit |
| پین F13 | UART0_RX — UART0 receive |
| پین E13 | UART1_TX — UART1 transmit |
| پین D12 | UART1_RX — UART1 receive |
| پین B11 | PWM_A0 — PWM channel A0 |
| پین B12 | PWM_B0 — PWM channel B0 |
| پین A13 | JTAG_TCK — JTAG test clock |
| پین A12 | JTAG_TMS — JTAG test mode select |
| پین B13 | JTAG_TDI — JTAG test data in |
| پین C13 | JTAG_TDO — JTAG test data out |
| پین A11 | RESET — Active-low reset input |
| پین N5 | XTAL_IN — Crystal oscillator input |
| پین P5 | XTAL_OUT — Crystal oscillator output |
| پین T5 | EXTAL_IN — External clock input |
| پین R5 | EXTAL_OUT — External clock output |
بەکارهێنانە باوەکان
MCF5282CVM66J گونجاوە بۆ 8 بەکارھێنانs: Industrial Ethernet Gateway, Building-Automation Controller, Factory-Automation PLC / Process Controller, Networked Sensor Hub / IoT Edge Node, CAN-Ethernet Bridge / Protocol Converter, Industrial Networking Equipment / Switch Controller, Motor / Motion Control Auxiliary Processor, Industrial Human-Machine Interface (HMI) Terminal.
Industrial Ethernet Gateway
The MCF5282CVM66J's 66.67 MHz ColdFire V2 core plus integrated 10/100 Ethernet MAC and CAN 2.0B controller make it a strong fit for industrial Ethernet gateway designs that must terminate both backhaul Ethernet and plant-floor CAN traffic. With 150 GPIO and 512 KB of flash, the part can host a TCP/IP stack, Modbus TCP bridge, and CANopen master in a single chip, removing the need for a companion network processor. EBI/EMI expansion lets engineers add SDRAM for higher-layer protocol buffers when handling many concurrent sockets; however the BGA package demands careful thermal-pad layout to dissipate the ~1.5 W typical core dissipation. Designed-in pairs that benefit here include external MII/RMII PHYs and industrial Ethernet magnetics.
پێشنیارکراو
Building-Automation Controller
For building-automation controllers (BACnet/IP, KNX/IP, LonWorks gateways), the MCF5282CVM66J delivers the deterministic interrupt response and the rich peripheral set needed to manage HVAC, lighting, and access-control subsystems from a single MCU. The PWM blocks drive analog-output stages for damper actuators; the UART/USART channels interface to RS-485 subnets; and the watchdog timer (WDT) plus low-voltage detect (LVD) give the field-reliable reset and brown-out behavior required for unattended installations. 512 KB of flash comfortably stores BACnet/IP objects and the protocol stack, while the 256-MAPBGA footprint is feasible on 4-layer FR4 PCBs provided the BGA is routed with 0.5 mm pitch escape rules. This is a strong fit for low-to-mid-tier controllers; very high-channel-count designs should step up to MCF5235CVM150 for 150 MHz throughput.
پێشنیارکراو
Factory-Automation PLC / Process Controller
The MCF5282CVM66J is well suited to small-scale factory-automation PLCs and process controllers where Ethernet connectivity and CAN fieldbus integration must coexist. The integrated DMA engine accelerates concurrent sampling of analog and digital inputs via the integrated PWM and timer modules, while the EBI/EMI bus allows fast external SDRAM and parallel I/O expansion. 150 GPIO are typically partitioned into isolated digital inputs, relay driver outputs, and HMI peripherals. The ColdFire V2 core's deterministic instruction timing suits IEC 61131-3 ladder-logic execution and a real-time operating system (RTOS) such as MQX or FreeRTOS for process control loops.
پێشنیارکراو
Networked Sensor Hub / IoT Edge Node
The MCF5282CVM66J's low dynamic power and integrated Ethernet MAC fit networked sensor hubs that aggregate data from multiple SPI-based sensors and forward readings over TCP/IP or MQTT. With 512 KB of flash, the part can host TLS handshake code, JSON/MQTT libraries, and device firmware update (DFU) routines; the DMA engine offloads sensor reads from the CPU, leaving headroom for security stacks. The 256-MAPBGA package is appropriate for industrial-grade edge nodes; designers should size the core supply decoupling to the BGA's power-pin grouping and use the LVD/POR blocks to enforce a clean power-up. For lower-power designs in the same family consider the MCF51CN successor.
پێشنیارکراو
CAN-Ethernet Bridge / Protocol Converter
Acting as a CAN-to-Ethernet bridge, the MCF5282CVM66J offers on-chip CAN 2.0B plus 10/100 Ethernet in a single MCU, simplifying the BOM for protocol-converter modules used to bring legacy CAN-based machinery onto modern plant networks. With 66.67 MHz and 512 KB of flash, the device can run transparent CAN-TCP/IP tunneling with filter masking; an external PHY (e.g. DP83848) completes the Ethernet interface. Care must be taken to gate the CAN bus transceiver's TX/RX paths through the isolated logic, and to enforce watch-dog timing for fail-safe recovery on bus errors. Same-family drop-in to MCF5282CVM80 boosts packet throughput where bottlenecks arise.
پێشنیارکراو
Industrial Networking Equipment / Switch Controller
The MCF5282CVM66J works as a control-plane processor in managed industrial switches and routers, where the integrated Ethernet MAC, CAN, and multiple UART/SPI ports allow local management via CLI, SNMP, or web interfaces. The EBI/EMI bus connects to a managed Ethernet switch ASIC and external memory, while the PWM/timer blocks drive status LEDs and watchdog timing. 512 KB of flash holds the management firmware and CLI commands; the 66.67 MHz speed grade is adequate for management-plane tasks but should be paired with a switch ASIC that handles wire-speed forwarding. Same-family 80 MHz parts provide headroom for larger routing-table workloads.
پێشنیارکراو
Motor / Motion Control Auxiliary Processor
The MCF5282CVM66J can serve as an auxiliary communications processor in a multi-axis motor-control system, translating EtherCAT, CANopen, or Modbus TCP commands into the host motion controller's preferred protocol. Its integrated Ethernet MAC, CAN, UART, and SPI peripherals cover the major industrial motion-control fieldbuses; 512 KB of flash is plenty for the bridge firmware. Designers can pair it with dedicated motor-control ASICs that handle the tight current-loop work, while the MCF5282CVM66J manages the slower network-side traffic. Same-family 80 MHz part is the drop-in upgrade when bridge latency matters.
پێشنیارکراو
Industrial Human-Machine Interface (HMI) Terminal
The MCF5282CVM66J powers low- to mid-tier industrial HMI terminals by driving an LCD controller over SPI, reading touch inputs via I2C or ADC, and uploading process data over Ethernet or CAN. Its 150 GPIO handle keypad matrix, status LEDs, and buzzer outputs; the integrated Ethernet and CAN give the HMI a direct connection to the PLC and to higher-level MES systems. 512 KB of flash supports graphical screen libraries and rich-text rendering, while the EBI/EMI allows external memory for full-frame buffers. Successor designs should evaluate the Kinetis E series for lower power and CAN-FD support.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCF5282CVM66J — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCF5282CVM80 | MCF5282CVF66 | MCF5282CVM66 | MCF5280CVM66 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 256-MAPBGA (17x17) | 256-MAPBGA (17x17) - same | 256-MAPBGA (17x17) - same | 256-MAPBGA (17x17) - same | 256-MAPBGA (17x17) - same |
| Core | ColdFire V2 | ColdFire V2 | ColdFire V2 | ColdFire V2 | ColdFire V2 |
| Clock Speed | 66.67 MHz | 80 MHz | 66 MHz | 66.67 MHz | 66 MHz |
| Program Flash | 512 KB | 512 KB | 512 KB | 512 KB | 0 KB (external only) |
| Ethernet | 10/100 Ethernet MAC | 10/100 Ethernet MAC | 10/100 Ethernet MAC | 10/100 Ethernet MAC | 10/100 Ethernet MAC |
| CAN | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| Number of I/O | 150 | 150 | 150 | 150 | 150 |
| Connection Supplements | CANbus, EBI/EMI, Ethernet, I2C, SPI, UART/USART | Same | Same | Same | Same |
جیاکەرەوە سەرەکییەکان
- Integrated 10/100 Ethernet MAC plus CAN 2.0B on a single ColdFire V2 die (بەراورد بەMCF5235CVM150)
- Same-package 80 MHz speed-grade drop-in alternative (بەراورد بەMCF5282CVM80)
- J-suffix variant preserves identical silicon with qualified-vendor packaging (بەراورد بەMCF5282CVM66 (non-J))
- MAPBGA-256 exposes 150 GPIO plus EBI/EMI for SDRAM and parallel flash (بەراورد بەMCF5213LCVM80)
- Same-footprint 0 KB flash variant available (بەراورد بەMCF5280CVM66)
تێبینییەکانی دیزاین
Estimated: at a 3.3 V core supply and 80 mA active core current (per typical MCF528x family values), the MAPBGA-256 dissipates roughly 0.26 W. The 17x17 mm MAPBGA thermal resistance is dominated by the PCB thermal pad; provide at least 1 square inch of continuous inner-plane copper tied to the BGA center-pad balls to keep the junction within industrial ranges. Avoid mounting the BGA onto a thermal keep-out island beneath a heatsink-less enclosure.
The 256-MAPBGA package uses 1.0 mm ball pitch; escape routing requires 0.2 mm laser-drilled micro-vias or 4-6 mil trace/space design rules. Place the MII/RMII traces within matched-length windows; group the analog VDD/RX-ER pins to allow a clean reference plane and minimize EMI. Decoupling: use a 0.1 uF X7R cap on every VDD/VSS pin pair plus 4.7 uF bulk capacitors close to the device's supply balls.
Because the MCF5282CVM66J is NRND and listed as Obsolete on third-party feeds, do not assume 10+ years of NXP factory support - validate your sourcing channel and broker traceability before certifying the design. Confirm the 'J' suffix variant matches your factory's qualification needs; mixing the J and non-J speeds on the same line is a common audit failure.
Power-on-reset (POR) timing depends on the external reset-capacitor selection on the RESET pin; the ColdFire V2 POR window is specified in the family user manual. Low-voltage detect (LVD) thresholds should be configured above the worst-case transient drop on the 3.3 V rail; failing to do so can cause brown-out resets in noisy industrial environments.
زانیاری پابەندبوون
Compliance fields were not explicitly provided in the verified web data; per the data authenticity rule these are reported as 'unknown' rather than fabricated. Industrial customers should request CMTR (Conflict Minerals Reporting Template) and RoHS/REACH test reports directly from NXP.