MCP2515-E/SO - CAN 2.0B SPI Controller, 18-SOIC, 125C | Microchip
MPN: MCP2515-E/SO ✓ چالاکMCP2515-E/SO گشتی
A CAN controller is a protocol-processing silicon block that sits between a host MCU and the physical CAN bus. The hierarchy runs from CAN controller, to CAN interface IC, to network interface IC, to general-purpose semiconductor. Unlike a CAN transceiver, which converts logic levels into differential bus voltages, the MCP2515-E/SO works purely at the frame level: it filters, prioritizes, arbitrates, and assembles CAN frames, while an external transceiver such as the MCP2551 or TJA1050 provides the physical layer.
Key features of the MCP2515-E/SO include full CAN 2.0B compliance, an SPI host interface, acceptance filtering with two acceptance masks and six acceptance filters, dual acceptance filters, programmable bit timing, a transmitted-data buffer, and dedicated interrupt output. The device is pin and function compatible with the first-generation MCP2510 while adding faster throughput, byte filtering, and support for time-triggered protocols. Frame data payloads of 0 to 8 bytes are supported.
Internally the controller separates the CAN receive path from the transmit path with dedicated buffers, and it implements a state machine that handles arbitration loss, error frames, and automatic retransmission. Because the MCP2515 is a host-driven device, the host MCU must service the interrupt line and drive the SPI transaction; this makes the part attractive in cost-sensitive designs where a high-speed MCU already exists on the board.
Typical uses include industrial CANopen and DeviceNet gateways, automotive body-comfort modules, elevator and building-automation controllers, EV charging station telemetry, test and measurement instrumentation, and hobbyist or maker platforms built on the widely available MCP2515 CAN module. The extended -40 °C to +125 °C grade makes it suitable for equipment installed near engines or in outdoor enclosures.
Design guidance centers on three points. First, decouple VDD and VREF close to the device with the values stated in the Microchip data sheet, because VREF noise maps directly into the received-bit threshold of the bus. Second, match the crystal or clock source to the bit-timing configuration; a mismatch shows up as error frames that are hard to diagnose. Third, provide a pull-up on the standby and reset pins so the controller stays in a defined state during power-up sequencing.
This page consolidates distributor pricing, verified package and temperature data, drop-in alternatives, comparison data, and practical integration notes that are not consolidated in any single manufacturer document, giving engineering teams a single reference for sourcing and design decisions.
جێگرەوەکانی جێگۆڕکێ بۆ MCP2515-E/SO — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MCP2515-E/SO (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, CAN Specification, Host Interface, Product Type, Clock Output.
MCP2515-I/SO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515T-E/SOVAO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515T-I/SO
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2515-E/SO تایبەتمەندییەکان
| Product Type | Stand-alone CAN controller with SPI host interface |
| CAN Specification | CAN 2.0B |
| Host Interface | SPI (Serial Peripheral Interface) |
| پاکێج | 18-pin SOIC (SO), surface mount |
| Package Pin Count | 18 pins |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +125 °C |
| Temperature Grade | -E (extended industrial/automotive temperature) |
| Frame Types Supported | Standard data, extended data, and remote frames |
| Maximum Data Field Length | 0 to 8 bytes |
| Acceptance Filtering | Two acceptance masks and six acceptance filters |
| Bit Timing | Programmable CAN bit timing with configurable sample point |
| Backward Compatibility | Pin and function compatible with the MCP2510 |
| Protocol Support | Time-triggered protocols supported |
| Standby / Reset Control | Dedicated STB (standby) and RES (reset) input pins |
| Clock Output | Dedicated CLKO output pin for external clock distribution |
| Interrupt | Dedicated INT output pin for host signalling |
| Transceiver Integration | None - external CAN transceiver required |
ڕێکخستنی پینی MCP2515-E/SO
| پین 1 | SCK — SPI clock input from host microcontroller |
| پین 2 | SO — SPI data output from controller to host |
| پین 3 | SI — SPI data input from host to controller |
| پین 4 | GND — Ground |
| پین 5 | VDD — Positive supply voltage |
| پین 6 | TXREQ — Transmit request; high requests transmission of the pending message |
| پین 7 | RXBF — Receive buffer full status output |
| پین 8 | CLKO — Clock output for external clock distribution |
| پین 9 | INT — Interrupt request output to host microcontroller |
| پین 10 | RXCAN — Receive input from CAN transceiver |
| پین 11 | TXCAN — Transmit output to CAN transceiver |
| پین 12 | VREF — Reference voltage input for transceiver mode |
| پین 13 | VREF — Reference voltage input (dual VREF connection) |
| پین 14 | GND — Ground |
| پین 15 | GND — Ground |
| پین 16 | STB — Standby input; high places controller in standby mode |
| پین 17 | RES — Reset input for the controller |
| پین 18 | DTR — Data terminal ready / SPI chip-select related control signal |
بەکارهێنانە باوەکان
MCP2515-E/SO گونجاوە بۆ 6 بەکارھێنانs: Industrial CANopen and DeviceNet Gateway, Automotive Body and Comfort Electronics, EV Charging Station Telemetry, Test and Measurement Instrumentation, Building Automation and HVAC Control, Maker and Educational CAN Bus Modules.
Industrial CANopen and DeviceNet Gateway
The MCP2515-E/SO fits industrial fieldbus gateways because it handles CAN 2.0B framing, arbitration loss, and error recovery entirely in hardware, leaving the host MCU to translate between the CAN payload and Ethernet or serial backhaul. Its two acceptance masks and six acceptance filters let a design pre-filter process-data frames before they ever reach the SPI bus, which cuts MCU interrupt traffic in gateways that carry hundreds of cyclic PDO frames. The -40 °C to +125 °C rating covers unheated outdoor cabinets and machine-side enclosures where industrial temperature grades are typically required. In practice the controller sits beside an MCP2551 or TJA1050 transceiver, and the host MCU services the dedicated INT pin for each received or completed transmitted frame.
پێشنیارکراو
Automotive Body and Comfort Electronics
Body-comfort modules such as door control units, seat controllers, and climate-panel interfaces frequently sit near hot power stages, which is where the extended -40 °C to +125 °C rating of the MCP2515-E/SO pays off. The controller handles bus arbitration and automatic retransmission on a loaded vehicle network, while the host MCU performs the actual comfort logic and diagnostic reporting. Because the MCP2515 is a protocol block rather than a transceiver, designers can select an automotive-qualified transceiver independently for high-speed bus capability and fault protection. Firmware portability across the MCP2515 family is straightforward because the acceptance mask, acceptance filter, and bit timing register layouts are shared, so validation effort transfers directly.
پێشنیارکراو
EV Charging Station Telemetry
EV charging stations use CAN links between the power-electronics controller, the payment and connectivity module, and the vehicle-side signalling path, and the MCP2515-E/SO is a natural fit for the low-speed signalling bus. The 18-pin SOIC package keeps the controller, its transceiver, and the isolation barrier within a compact area in a sealed cabinet that can reach high internal temperatures during fast-charge operation. The dedicated standby (STB) pin lets the charging controller power down the CAN node between sessions, while the reset (RES) pin supports deterministic power-up sequencing. Where the design also needs CAN FD on a separate link, the MCP25625 family offers a compatible upgrade path, though it is a different package and is not a drop-in replacement.
پێشنیارکراو
Test and Measurement Instrumentation
Bench instruments and production-line testers often need to log or inject frames on an existing vehicle or factory CAN network, and the MCP2515-E/SO provides the frame-level access needed for that. Because the host MCU controls bit timing and filtering through SPI, a test set can act as a passive sniffer using the acceptance masks and filters to capture only the identifiers of interest, or as an active node injecting standard and extended frames during fault-injection campaigns. The -E temperature grade also allows the same board to be used in climatic test chambers and unheated field service kits. A companion transceiver such as the MCP2551-I/SN completes the physical layer, and the isolated CAN option in the MCP25625 family is worth evaluating for lab safety.
پێشنیارکراو
Building Automation and HVAC Control
HVAC controllers, room thermostats, and lighting managers in commercial buildings frequently use CAN for sensor and actuator networking, and the MCP2515-E/SO handles that traffic efficiently at very low cost. Because the controller performs filtering in hardware, a thermostat can monitor dozens of room-sensor identifiers while the host MCU only processes the frames that actually matter, reducing both interrupt rate and SPI bus occupancy. The extended temperature range covers unheated rooftop units and plant-room cabinets, and the standby input lets the board sleep between polling intervals. Deployments that need higher bus speed or CAN FD eventually outgrow the 2.0B-only controller, but for classic CANopen building profiles the MCP2515 remains a proven, widely supported choice.
پێشنیارکراو
Maker and Educational CAN Bus Modules
The MCP2515-E/SO is the silicon at the heart of the widely sold MCP2515 CAN breakout modules used with Arduino, ESP32, and Raspberry Pi boards, and it remains the most budget-friendly way to add a CAN port to a maker project. It runs from a low-voltage rail, needs only a handful of external components including a crystal and decoupling, and is supported by mature open-source Arduino and Python driver libraries that map directly onto the documented SPI register set. The 18-pin SOIC footprint is available in inexpensive volume quantities, and the -E grade lets student designs run in a car, a robot, or a solar-powered outdoor sensor without thermal concerns. Adding an MCP25625-based module is the usual upgrade path when a project needs CAN FD.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MCP2515-E/SO — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MCP2515-I/SO | MCP2515T-E/SO | MCP2515T-I/SO |
|---|---|---|---|---|
| Package | 18-pin SOIC (SO) | 18-pin SOIC (SO) - same | 18-pin SOIC (SO) - same | 18-pin SOIC (SO) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +85 °C (about 40 °C lower maximum) | -40 °C to +125 °C (identical) | -40 °C to +85 °C (about 40 °C lower maximum) |
| CAN Specification | CAN 2.0B | CAN 2.0B | CAN 2.0B | CAN 2.0B |
| Host Interface | SPI | SPI | SPI | SPI |
| Acceptance Filtering | Two acceptance masks and six acceptance filters | Two acceptance masks and six acceptance filters | Two acceptance masks and six acceptance filters | Two acceptance masks and six acceptance filters |
| Frame Support | Standard, extended data, and remote frames | Standard, extended data, and remote frames | Standard, extended data, and remote frames | Standard, extended data, and remote frames |
| Transceiver Integration | None - external CAN transceiver required | None - external CAN transceiver required | None - external CAN transceiver required | None - external CAN transceiver required |
جیاکەرەوە سەرەکییەکان
- Extended temperature rating versus the -I grade sibling (بەراورد بەMCP2515-I/SO)
- Hardware CAN 2.0B filtering reduces host MCU interrupt load (بەراورد بەSoftware CAN implementation on a generic MCU)
- Drop-in pin and function compatibility with the first-generation MCP2510 (بەراورد بەMCP2510)
- Protocol-layer separation from the transceiver allows independent part selection (بەراورد بەMCP2551-I/SN)
تێبینییەکانی دیزاین
Route the SPI bus (SCK, SI, SO, CS) as a short, contiguous group between the host MCU and the MCP2515-E/SO, and keep the CAN transceiver RXCAN/TXCAN traces away from the SPI and clock lines to avoid coupling SPI activity into the receive path. Place the crystal close to pins 1 and 5 with a short ground return, since a long or noisy oscillator path shows up as intermittent CAN error frames and burst errors rather than as a clean failure. Provide the full decoupling network called out in the Microchip MCP2515 Family Data Sheet (DS20001801K) at VDD and at the dual VREF pins, and route VREF as a quiet analog-style trace back to the transceiver reference.
The MCP2515-E/SO is a protocol controller and draws little current, but the surrounding design still needs deliberate power sequencing. Hold the controller in standby or reset with the STB and RES pins until the host MCU and the CAN transceiver rails are stable, because a released reset on an unpowered transceiver can produce spurious bus frames. Tie RES and STB to defined levels rather than leaving them floating, and use the CLKO output only when the downstream circuit can tolerate the extra load it places on the oscillator. If the board sits next to a switching regulator, feed the controller from a post-filtered rail to keep conducted noise from appearing as bit errors.
The most common integration errors are clocking and protocol mismatches. First, bit timing must be programmed to match the physical bus speed, sample point, and oscillator tolerance, otherwise error frames accumulate silently while the link appears alive. Second, MCP2515 CAN 2.0B does not support CAN FD; if the target network runs FD, migrate to the MCP25625 family rather than forcing legacy frames onto an FD bus. Third, many boards built around MCP2515 modules assume the chip includes a transceiver - it does not, and omitting the external transceiver is the single most frequent bring-up failure. Finally, verify the acceptance filter configuration, because over-restrictive masks silently discard frames that the application expects to receive.
زانیاری پابەندبوون
RoHS and REACH compliance are referenced generically in third-party comparison listings for this part but no explicit compliance statement was present in the retrieved manufacturer or distributor pages, so these fields are marked unknown. The MCP2515-E/SO is an industrial-temperature grade device and is not marketed as an AEC-Q100 qualified automotive part.