MK2308S-1HLF - 133MHz 8-Output Zero Delay Buffer | Renesas
MPN: MK2308S-1HLF ✓ چالاکMK2308S-1HLF گشتی
A zero-delay buffer is a clock-and-timing IC that regenerates a clock signal while using a phase-locked loop to minimize propagation delay between input and output. Its hierarchy is zero-delay buffer, clock buffer, clock driver, clock and timing IC, and integrated circuit. This topology helps distribute a high-speed source clock to multiple loads while controlling skew and jitter.
The principal features of the MK2308S-1HLF include eight outputs, a maximum operating frequency of 133 MHz, 200 ps output skew, a 3 V to 3.6 V supply range, and CMOS interfacing. Each output can support tri-state operation, while the PLL-based architecture allows direct-input testing for circuit development and clock-tree analysis.
Technically, the MK2308S-1HLF separates clock generation from distribution by using low-jitter PLL techniques. The eight outputs are intended to provide closely aligned copies of a common clock source. In zero-delay mode, the PLL compensates for internal propagation paths; in direct mode, the source clock can be routed without the PLL to help evaluate source behavior or board-level timing.
Typical applications include processor and FPGA clock distribution, memory-controller fanout, networking-interface clock trees, test-and-measurement systems, and communications equipment operating at 3.3 V. It is particularly useful when several sequential circuits require related clock outputs and low output-to-output skew is more important than minimizing power consumption.
Design the input and output clock paths for controlled impedance, maintain short and symmetric routing, and use the manufacturer pin-description table when assigning board connections. Decoupling, grounding, and unused-output handling should follow the manufacturer datasheet, especially when outputs are left unconnected or driven in tri-state mode.
This page combines the MK2308S-1HLF operating specifications, pin-compatible family options, application guidance, and practical clock-tree design notes. It is structured to help engineers compare functionality, verify the 133 MHz and 200 ps timing targets, and assess where an eight-output 3.3 V zero-delay buffer fits within a larger clock-and-timing architecture.
جێگرەوەکانی جێگۆڕکێ بۆ MK2308S-1HLF — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ MK2308S-1HLF (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Device Type, Maximum Frequency, Supply Voltage Range, Package Type.
MK2308S-1HLFTR
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MK2308S-1HLFT
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MK2308S-2LF
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →MK2308S-1H
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →CY2308SI-1T
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MK2308S-1HLF تایبەتمەندییەکان
| Device Type | Zero Delay Buffer / Clock Driver |
| Maximum Frequency | 133 MHz |
| Supply Voltage Range | 3 V to 3.6 V |
| Output Skew | 200 ps |
| ژمارەی دەرچووەکان | 8 outputs |
| Bus Interface | CMOS |
| PLL Architecture | Yes, with bypass |
| Output Modes | PLL zero-delay, direct input, and tri-state |
| Package Type | 16-pin SOIC, 0.150 inch width, 3.90 mm |
| جۆری دامەزراندن | Surface mount |
| Lead-Free Finish | Lead-free |
| Phase Noise | Low phase noise |
| Jitter | Low jitter |
ڕێنمایی ڕێکخستنی پینی MK2308S-1HLF 16-pin soic, 0.150 inch width, 3.90 mm
ڕێکخستنی پین بۆ MK2308S-1HLF (پاکێجی 16-pin soic, 0.150 inch width, 3.90 mm). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ MK2308S-1HLF.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
MK2308S-1HLF گونجاوە بۆ 6 بەکارھێنانs: FPGA Clock Distribution, Memory Controller Clock Fanout, Networking Equipment Clock Tree, Test and Measurement Instrumentation, Communications Baseband Processing, Industrial Control and Data Acquisition.
FPGA Clock Distribution
The MK2308S-1HLF fits an FPGA clock tree that requires multiple closely related outputs at up to 133 MHz. Its eight CMOS outputs can fan a common clock to fabric, memory interface, communications, and debug logic without requiring eight independent clock sources. The specified 200 ps output skew provides a defined alignment target, while PLL mode provides near-zero-delay operation and direct-input bypass supports board-level source testing. Designers should still compare the 200 ps skew with the FPGA setup-and-hold budget and use equalized routing to prevent board skew from consuming the timing margin.
پێشنیارکراو
Memory Controller Clock Fanout
The MK2308S-1HLF is suitable for distributing a 133 MHz memory-controller clock to related loads when the design needs eight outputs and controlled alignment. Its PLL-based zero-delay operation can compensate for internal buffer delay, while direct-input mode provides a way to evaluate the source clock independently of PLL behavior. The 200 ps specified skew is important because memory interfaces may have limited margin between clock and data timing. Use the pin-description table from the manufacturer datasheet, keep clock traces short, and confirm that every driven output meets the voltage and timing requirements of the connected memory device.
پێشنیارکراو
Networking Equipment Clock Tree
The MK2308S-1HLF can support networking-equipment clock distribution where a 3.3 V system requires up to eight related CMOS clock outputs at no more than 133 MHz. The eight-output architecture suits line cards, interface controllers, transceivers, and monitoring subsystems that benefit from a common phase reference. Low phase noise and low jitter are meaningful for communication timing, and the 200 ps skew specification provides a basis for topology planning. Final adoption depends on receiver jitter tolerance, channel bandwidth, isolation requirements, and whether bypass mode is needed during production diagnostics.
پێشنیارکراو
Test and Measurement Instrumentation
The MK2308S-1HLF is useful in test and measurement instrumentation that needs to fan a reference clock into several acquisition, triggering, or conversion paths. Eight outputs permit centralized distribution up to 133 MHz, while PLL bypass gives engineers a practical diagnostic mode for checking behavior at the source clock. The specified 200 ps skew supports predictable relative timing between channels, although cable, connector, and instrument delays may dominate in a complete system. Engineers should use low-skew routing, maintain a continuous return path, and account for loading on each CMOS output.
پێشنیارکراو
Communications Baseband Processing
The MK2308S-1HLF can distribute a baseband processing clock across DSP, converter, and interface blocks operating up to 133 MHz. Eight outputs reduce duplicated clock-generation circuitry and help maintain a common timing reference, while low phase noise and low jitter are valuable in communications systems. PLL bypass permits controlled testing of the source and helps isolate board timing behavior. The design should verify the 3 V to 3.6 V supply tolerance, confirm output logic levels for every load, and budget the 200 ps device skew against the processing devices' timing requirements.
پێشنیارکراو
Industrial Control and Data Acquisition
The MK2308S-1HLF supports industrial control and data-acquisition designs that synchronize several subsystems from a 3.3 V clock operating up to 133 MHz. Eight outputs can serve processors, counters, converters, and communication interfaces, reducing the number of independent clock paths. The low-skew PLL architecture improves consistency among related signals, and tri-state control offers flexibility when a subsystem is disabled or placed into a test state. Engineers should verify operating-temperature requirements for the exact ordering code, use solid grounding and decoupling, and avoid introducing excessive fanout through unbuffered branches.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ MK2308S-1HLF — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | MK2308S-1HLFTR | MK2308S-1HLFT | MK2308S-2LF | MK2308S-1 | CY2308SI-1T |
|---|---|---|---|---|---|---|
| Device Type | PLL-based zero-delay buffer | PLL-based zero-delay buffer | PLL-based zero-delay buffer | PLL-based zero-delay buffer | PLL-based zero-delay buffer | Zero-delay buffer |
| Package | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 | SOIC-16 |
| Brand | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Renesas Electronics | Cypress Semiconductor |
| Maximum Frequency | 133 MHz | 133 MHz | 133 MHz | 133 MHz | 133 MHz | 133 MHz |
جیاکەرەوە سەرەکییەکان
- Eight-output clock distribution in one device (بەراورد بەCY2308SI-1T)
- Specified low output skew (بەراورد بەCY2308SI-1T)
- Integrated PLL and direct-input test path (بەراورد بەMK2308S-2LF)
تێبینییەکانی دیزاین
Treat the eight outputs as a matched clock tree rather than independent point-to-point nets. Route the outputs with similar geometry and loading, provide a continuous ground reference, and avoid adding large stubs or unequal connectors. The manufacturer specifies 200 ps output skew, but PCB trace-length differences, connector delays, and receiver variation can consume that budget. Validate the complete branch topology with an oscilloscope or timing analyzer at the intended 133 MHz operating point.
Place the input, output, and bypass connections according to the manufacturer layout guidance, and keep the clock input trace short and away from switching nodes. The device operates from 3 V to 3.6 V, so local decoupling should be placed at the power pins with an uninterrupted return path. Because the MK2308S-1HLF uses a PLL for zero-delay operation, preserve a stable supply and reference path to avoid translating power-supply noise directly into clock jitter.
Do not treat PLL bypass as an electrically identical operating condition merely because both paths produce clock outputs. PLL mode compensates internal delay, whereas direct-input mode is intended for testing and can expose different timing behavior. Confirm output enable polarity, tri-state state, and unused-pin treatment using the manufacturer pin-description table. Also verify the exact ordering-code temperature grade and lifecycle status before treating any MK2308S suffix as an interchangeable production alternative.
زانیاری پابەندبوون
The HLF ordering suffix identifies a lead-free package. No explicit RoHS, REACH, halogen-free, conflict-minerals, or automotive qualification statement was identified for the exact MPN.