Microchip Technology

PIC12F617-I/MS - 8-Bit 20MHz Flash MCU | Microchip

MPN: PIC12F617-I/MS ✓ چالاک
25 mA Id 8-pin MSOP Package 20 MHz Speed 3.5 KB Flash Memory
MOQ: 1 |

PIC12F617-I/MS گشتی

Microchip Technology PIC12F617-I/MS is an 8-bit flash-programmable CMOS microcontroller with a 20 MHz maximum instruction-clock rate, 3.5 KB of program Flash memory, 128 bytes of RAM, and six general-purpose I/O pins. The device is offered in an 8-pin MSOP package. According to the manufacturer product page, the PIC12F617 is in production, making it suitable for compact embedded-control designs requiring a small package and straightforward peripheral integration.

A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The PIC12F617 belongs to the PIC12 family of 8-bit RISC microcontrollers, which sits within the broader hierarchy of embedded controllers, microcontrollers, and semiconductors. Its mid-range core uses 35 single-word instructions and provides eight hardware stack levels, offering a practical balance of processing capability, code efficiency, and implementation simplicity.

PIC12F617-I/MS provides 3.5 KB of self-read, self-write Flash program memory, 128 bytes of data RAM, and six I/O pins. Its internal oscillator is specified at 8 MHz, while the device family supports operation up to 20 MHz. Two 8-bit timers, one 16-bit timer, and a comparator with configurable hysteresis support timing, control, and basic analog-interface applications. Individual I/O pins are specified for 25 mA source or sink current.

The internal oscillator removes the need for an external clock in many designs, helping reduce component count and board area. The comparator can monitor an analog input and generate a hardware interrupt or drive control logic, while the timer structure supports periodic events, time measurement, and basic motor or timing-control functions. Firmware can be developed with Microchip-compatible PIC tooling, including the MPLAB environment and PIC programmer families identified on the manufacturer product page.

Typical uses include compact sensor-control modules, LED-status indicators, simple motor or actuator controllers, appliance interfaces, and low-cost embedded timers. The small 8-pin MSOP package is particularly useful where PCB space is constrained and the design requires only a modest number of I/O connections. Designers should verify voltage, current, timer, and comparator limits against the manufacturer datasheet for the exact operating condition.

For a new PCB, assign VDD and VSS before connecting external circuitry, keep decoupling capacitors close to their pins, and route oscillator-sensitive signals away from high-current switching nodes. When upgrading an existing design, compare pin functions, memory requirements, interrupt behavior, and programming requirements before treating another controller as a drop-in replacement.

This page combines the exact orderable MPN, manufacturer and distributor product information, package-specific guidance, practical application context, and a structured comparison of same-package Microchip PIC12 alternatives. These engineering details help narrow the replacement decision while preserving the distinction between electrical compatibility and complete functional equivalence.

جێگرەوەکانی جێگۆڕکێ بۆ PIC12F617-I/MS — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PIC12F617-I/MS (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Internal Oscillator, Timers, Comparator, Core Architecture, Program Memory.

Microchip Technology
Internal Oscillator: 8 MHz (factory calibrated)
Timers: 1 x 8-bit, 1 x 16-bit
Core Architecture: 8-bit PIC RISC (mid-range)
Microchip Technology
Internal Oscillator: 8 MHz
Program Memory: 1.75 KB (1K x 14 words)
Microchip Technology
Timers: 1 x 8-bit, 1 x 16-bit
Core Architecture: 8-bit RISC (Harvard)
Microchip Technology
Internal Oscillator: 4/8 MHz user-selectable
Timers: TMR0 (8-bit), TMR1 (16-bit), TMR2 (8-bit)
Comparator: 1 with configurable hysteresis
Microchip Technology
Internal Oscillator: 4 MHz or 8 MHz, software selectable, factory calibrated
Timers: 2 × 8-bit (TMR0/TMR2) + 1 × 16-bit
Comparator: 1 internal, configurable hysteresis

PIC12F617-E/MS

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Microchip Technology
📦 8-pin MSOP
PIC12 mid-range 8-bit RISC · 35 single-word instructions · 3.5 KB (2K x 14) Flash · 128 bytes · 20 MHz · 200 ns at 20 MHz · 6

پەیوەندی بۆ نرخ

بینینی داتاشیت →

PIC12F615-I/MS

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Microchip Technology
📦 8-pin MSOP
PIC® 12F · 8-bit RISC (Harvard) · 8-bit · Flash · 1.75 KB (1K x 14) · 64 bytes · 128 bytes · 20 MHz

پەیوەندی بۆ نرخ

بینینی داتاشیت →

PIC12F616-I/MS

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin MSOP
Flash memory is 2 KB versus 3.5 KB, a 43% reduction; RAM remains 128 B and I/O remains 6 pins.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

PIC12F675-I/MS

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin MSOP
Flash memory is 4 KB versus 3.5 KB, a 14% increase, with a broader mixed-signal peripheral set.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

PIC12F683-I/MS

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin MSOP
Flash memory is 8 KB versus 3.5 KB, a 129% increase, while retaining the PIC12 mid-range core and 6 I/O pins.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

PIC12F617-I/MS زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Architecture 8-bit RISC
زۆرترین فرێکوێنسیی کاتژمێر 20 MHz
Internal Oscillator Frequency 8 MHz
Program Memory 3.5 KB Flash
Data Memory 128 B RAM
General-Purpose I/O 6 pins
I/O Source/Sink Current 25 mA
Instruction Set 35 single-word instructions
Hardware Stack Depth 8 levels
8-Bit Timers 2 timers
16-Bit Timer 1 timer
Comparator 1 comparator with configurable hysteresis
Program Memory Type Self-read, self-write Flash
Process Technology CMOS
پاکێج 8-pin MSOP
جۆری دامەزراندن Surface mount

ڕێنمایی ڕێکخستنی پینی PIC12F617-I/MS 8-pin msop

ڕێکخستنی پین بۆ PIC12F617-I/MS (پاکێجی 8-pin msop). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.

نەخشەی پینئاوتی پاکێجی 8-pin msop بۆ PIC12F617-I/MS

هیچ داتای وردی پینئاوت بەردەست نییە بۆ PIC12F617-I/MS.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

PIC12F617-I/MS گونجاوە بۆ 6 بەکارھێنانs: Compact Sensor-Control Module, LED Status and Sequencer, Simple Motor and Actuator Control, Appliance Control Interface, Battery-Powered Timer Module, Programmable Threshold Detector.

🧩

Compact Sensor-Control Module

PIC12F617-I/MS fits compact sensor-control modules because it combines a 20 MHz maximum clock, 3.5 KB of Flash, 128 bytes of RAM, and six I/O pins in an 8-pin MSOP package. The comparator can perform threshold detection, while its configurable hysteresis helps prevent repeated switching around a changing sensor signal. Place the device between the sensor interface and a small actuator or digital output stage. The internal 8 MHz oscillator can reduce external clock components, although the final oscillator, operating-voltage, and timing configuration should be checked for the target sensor bandwidth.

💡

LED Status and Sequencer

PIC12F617-I/MS can control LED status indicators, sequencing patterns, or simple panel indicators using its six I/O pins and timer resources. The 3.5 KB Flash area provides room for lookup tables and multiple animation patterns, while 128 bytes of RAM can hold counters, debounce state, and sequence position. One 16-bit timer and two 8-bit timers can establish different timing intervals without relying on software delays. The 25 mA per-pin source or sink rating should be checked against the LED configuration, and series-current limiting plus a common-anode or common-cathode drive arrangement will determine the practical loading.

🏭

Simple Motor and Actuator Control

PIC12F617-I/MS is suitable for small actuator-control tasks where six I/O pins, programmable timers, and an 8-bit architecture are sufficient. Timers can generate fixed-duration drive pulses, count external events, or support a basic closed-loop interval, while the 20 MHz maximum clock provides additional processing headroom. Its 25 mA source or sink specification suits low-current logic and driver-control signals, not direct high-current motor drive. A transistor or integrated motor driver must handle the load, and flyback protection, thermal margin, and supply sizing should be determined from the actuator characteristics.

🔧

Appliance Control Interface

PIC12F617-I/MS can serve as the local controller in an appliance or equipment interface where a compact PCB, event-driven input handling, and a small number of outputs are required. The six I/O pins can support buttons, mode indicators, relay-control logic, and discrete sensors, while the comparator provides a hardware threshold function for simple analog detection. With 3.5 KB of Flash and 128 bytes of RAM, firmware can implement a state machine, debouncing, timing, and fault flags. For mains-connected equipment, maintain the required separation between control logic and hazardous voltage and verify isolation and protection independently.

⚡

Battery-Powered Timer Module

PIC12F617-I/MS supports compact battery-powered timer modules where low component count, programmable intervals, and modest code size are important. The 8 MHz internal oscillator eliminates a mandatory external clock in suitable designs, while the timers support periodic wake-up, elapsed-time measurement, and output-pulse generation. The 3.5 KB Flash capacity accommodates a small scheduler and configuration table, and the comparator can monitor a battery-derived threshold when its operating limits are satisfied. Average-current performance depends on the selected clock configuration, sleep behavior, and peripheral use, so battery life should be calculated for the actual operating cycle.

📺

Programmable Threshold Detector

PIC12F617-I/MS can implement a programmable threshold detector using its comparator with user-configurable hysteresis. A sensor or divided supply can drive the comparator input, while firmware responds to the output state or comparator interrupt to update an indicator, set a latch, or trigger a counter. The 20 MHz maximum clock gives sufficient control-loop headroom for debouncing and event classification, and the 8-pin MSOP package supports compact installation. Verify input common-mode range, comparator response, output polarity, and supply-voltage requirements before finalizing the threshold circuit.

What are the key specifications of PIC12F617-I/MS that engineers should know?
PIC12F617-I/MS is an 8-bit flash-programmable microcontroller with a 20 MHz maximum clock, 3.5 KB of Flash program memory, 128 bytes of RAM, and six I/O pins in an 8-pin MSOP package. According to the Microchip PIC12F617 datasheet, it also includes an 8 MHz internal oscillator, 35 single-word instructions, eight stack levels, two 8-bit timers, one 16-bit timer, and a comparator with configurable hysteresis.
Where can I download the PIC12F617 datasheet PDF?
The official PIC12F617 datasheet is available from the Microchip product page and the linked manufacturer PDF resources. The product page identifies PIC12F617 as an in-production device and provides the data-sheet download. A third-party PDF is also indexed for the PIC12F609, PIC12F615, and PIC12F617 family, but the Microchip copy should be preferred when checking pin limits, electrical characteristics, timing, and programming requirements.
What is the PIC12F617-I/MS pinout and package?
PIC12F617-I/MS uses an 8-pin surface-mount MSOP package. The family integrates six I/O pins alongside power connections and programming-related functions, but exact physical pin assignments should be taken from the manufacturer pin-description table. The package drawing in the Microchip PIC12F617 datasheet must be cross-checked against the PCB footprint and the selected programming connector before layout release.
How much Flash memory and RAM does PIC12F617-I/MS have?
PIC12F617-I/MS provides 3.5 KB of self-read, self-write Flash program memory and 128 bytes of RAM. According to the Microchip PIC12F617 datasheet, the device has a mid-range core with 35 single-word instructions and eight hardware stack levels. When sizing firmware, reserve program-memory space for the bootloader, configuration words, constants, and interrupt-service routines rather than planning to fill all 3.5 KB with application code.
Can PIC12F617-I/MS run at 20 MHz?
Yes, PIC12F617-I/MS supports a maximum clock frequency of 20 MHz. The manufacturer also identifies an 8 MHz internal oscillator, allowing designs to avoid an external clock when suitable performance and peripheral timing are sufficient. Confirm the operating voltage, oscillator configuration, timing margins, and I/O behavior associated with the selected 20 MHz operating condition in the manufacturer datasheet.
What peripherals are available on PIC12F617-I/MS?
PIC12F617-I/MS includes six general-purpose I/O pins, two 8-bit timers, one 16-bit timer, and one comparator with user-configurable hysteresis. Individual I/O pins are specified for 25 mA source or sink current. These resources support periodic timing, elapsed-time measurement, threshold detection, and control-loop functions while keeping the device within an 8-pin MSOP footprint.
What can replace PIC12F617-I/MS?
The closest replacements are same-package Microchip PIC12 devices that preserve the 8-pin MSOP footprint and mid-range architecture, including PIC12F617-E/MS, PIC12F615-I/MS, PIC12F616-I/MS, PIC12F675-I/MS, and PIC12F683-I/MS. A true drop-in choice must match voltage, memory, peripheral, temperature, pin-function, programming, and timing requirements; having the same package alone does not guarantee functional equivalence.
Is PIC12F617-I/MS the same as PIC12F617-E/MS?
PIC12F617-I/MS and PIC12F617-E/MS share the base PIC12F617 device and 8-pin MSOP package, while the final character selects a different temperature grade. Their Flash memory, RAM, I/O count, clock capability, timers, and comparator are unchanged. The I-grade choice is generally appropriate when a wider industrial temperature range is required; verify the exact grade limits in the manufacturer ordering information.
PIC12F617-I/MS vs PIC12F615-I/MS - which is better for a compact timer controller?
Choose PIC12F617-I/MS when the firmware and application benefit from 3.5 KB of Flash rather than the PIC12F615's smaller memory allocation. Both devices provide six I/O pins, timer resources, an internal oscillator, and the same 8-pin MSOP family context, so the decision should be driven by code size, required peripherals, voltage, and timing. PIC12F617-I/MS offers 1.5 KB more Flash memory than PIC12F615-I/MS.
When should I choose PIC12F617-I/MS over PIC12F675-I/MS?
Choose PIC12F617-I/MS when its 3.5 KB Flash program memory, 128-byte RAM, and six I/O pins satisfy the design and you want to minimize feature complexity. PIC12F675-I/MS provides 4 KB of Flash and a broader peripheral set, making it attractive for applications needing additional mixed-signal capability. Confirm that every required peripheral, pin function, interrupt, and timing resource is present before changing the PCB or firmware.
Is PIC12F617-I/MS suitable for battery-powered embedded control?
PIC12F617-I/MS can suit battery-powered embedded-control systems when the firmware uses its 8 MHz internal oscillator efficiently and the design does not require continuous high-speed operation. The 3.5 KB Flash capacity can reduce the need for a separate program-memory device, while the comparator and timers support low-power sensing and wake-up functions. Evaluate average current, sleep behavior, and analog-control requirements in the operating system.
How should I design the PCB around PIC12F617-I/MS?
Place the required supply-decoupling capacitor adjacent to the VDD and VSS connections, keep the traces short, and route the footprint to the mechanical dimensions in the package drawing. Use a stable programming connector and accessible test points when production testing is required. Avoid long traces beside switching nodes, particularly when the internal oscillator is used and signal integrity or timing margins are important.
Where can I buy PIC12F617-I/MS and what is the current lead time?
Use the Request a Quote form on this page to request PIC12F617-I/MS availability, current lead time, minimum order quantity, and order confirmation. The manufacturer lists the PIC12F617 family as in production, while exact stock and delivery timing can change by lot, quantity, and fulfillment method. The Request a Quote workflow provides the appropriate current purchasing response.
Is PIC12F617-I/MS in stock?
PIC12F617-I/MS is shown as in stock by at least one indexed distributor listing, and the manufacturer identifies the base PIC12F617 family as in production. Inventory is dynamic and may differ by package suffix, lot, and distributor location. Use the Request a Quote form on this page for a current availability check before committing the design to a procurement date.
What is the price of PIC12F617-I/MS?
Use the Request a Quote form on this page for the current price of PIC12F617-I/MS. The indexed listing contains a starting price rather than an explicit quantity-break table for the exact orderable MPN, so no static price schedule is published on this page. A quote request can confirm unit pricing, volume breaks, stock, and delivery information for the intended quantity.
Which programming tools are compatible with PIC12F617-I/MS?
PIC12F617-I/MS is supported by the Microchip PIC programming and development ecosystem associated with the manufacturer product page, including MPLAB tooling and compatible PIC programmers. The exact programmer connector, programming voltages, interface protocol, and supported device entry should be checked against current Microchip tooling documentation. Confirm programming and verification successfully before committing production volume.

داتای سەرچاوەی ئەندازیاری بۆ PIC12F617-I/MS — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose PIC12F617-I/MS when an 8-pin MSOP design needs up to 3.5 KB of Flash, 128 bytes of RAM, six I/O pins, timers, and a comparator with configurable hysteresis. Choose PIC12F617-E/MS when the electrical configuration is identical but the E temperature grade better matches the product environment. PIC12F615-I/MS and PIC12F616-I/MS are useful when 2 KB of Flash is sufficient, but firmware must be reduced by at least 1.5 KB relative to PIC12F617-I/MS. Select PIC12F675-I/MS when 4 KB of Flash and a broader mixed-signal peripheral set justify the additional complexity. PIC12F683-I/MS is appropriate when 8 KB of Flash and 256 bytes of RAM are required. For every candidate, verify pin multiplexing, voltage limits, timing, temperature grade, programming configuration, and peripheral behavior before treating it as a drop-in replacement.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە PIC12F617-E/MS PIC12F615-I/MS PIC12F616-I/MS PIC12F675-I/MS PIC12F683-I/MS
Package 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP 8-pin MSOP
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Architecture 8-bit RISC 8-bit RISC 8-bit RISC 8-bit RISC 8-bit RISC 8-bit RISC
Maximum Clock Frequency 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz 20 MHz
Flash Program Memory 3.5 KB 3.5 KB 2 KB 2 KB 4 KB 8 KB
RAM 128 B 128 B 128 B 128 B 128 B 256 B
General-Purpose I/O 6 pins 6 pins 6 pins 6 pins 6 pins 6 pins
Internal Oscillator 8 MHz 8 MHz 8 MHz 8 MHz 8 MHz 8 MHz
Temperature Grade I grade E grade I grade I grade I grade I grade

جیاکەرەوە سەرەکییەکان

  • Larger Flash allocation than PIC12F615-I/MS and PIC12F616-I/MS (بەراورد بەPIC12F615-I/MS)
  • Same electrical configuration as the alternate-temperature PIC12F617 (بەراورد بەPIC12F617-E/MS)
  • Smaller memory footprint than PIC12F683-I/MS (بەراورد بەPIC12F683-I/MS)
  • Focused resource set compared with PIC12F675-I/MS (بەراورد بەPIC12F675-I/MS)

تێبینییەکانی دیزاین

Use the manufacturer package drawing to establish the 8-pin MSOP land pattern and do not substitute a generic SOIC-8 footprint based only on pin count. Place the supply-decoupling capacitor immediately between the VDD and VSS pins, minimize the loop area, and provide a clean ground connection. Confirm programming access, exposed pad requirements, solder mask clearance, and assembly tolerances before releasing the PCB files.

When the 8 MHz internal oscillator drives timing-sensitive measurements, keep sensor inputs and programming lines away from switching-node copper. Use a short ground reference and avoid routing comparator inputs beneath digital clock or high-current output traces. If precision timing is required, evaluate the maximum 20 MHz operating condition, oscillator tolerance, and peripheral jitter against the system budget using the manufacturer timing characteristics.

Do not assume that equal package dimensions guarantee a drop-in replacement. PIC12F617 alternatives can differ in Flash size, RAM, comparator features, pin multiplexing, configuration bits, and temperature grade. Before substituting a device, compare its pin-description table, electrical limits, interrupt map, configuration words, programming settings, and application code. Preserve decoupling and programming-test access in the original layout.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance attributes are not stated on the indexed product pages. AEC-Q100 status is not applicable because the target is an industrial-temperature microcontroller rather than an automotive-qualified ordering option.

داتا پشتڕاستکراوەتەوە لە: 2026-11-04 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

pic12f617 datasheet pdf pic12f617 datasheet PIC12F617-I/MS pinout PIC12F617-I/MS specifications PIC12F617-I/MS application circuit PIC12F617-I/MS equivalent PIC12F617-I/MS replacement PIC12F617-I/MS cross reference PIC12F617-I/MS vs PIC12F615-I/MS PIC12F617-I/MS MSOP footprint PIC12F617-I/MS price PIC12F617-I/MS stock Microchip PIC12F617-I/MS

پێکهاتە و زاراوە پەیوەندیدارەکان

Microchip Technology PIC12F617-I/MS PIC12F617 PIC12F617-E/MS PIC12F615-I/MS PIC12F616-I/MS PIC12F675-I/MS PIC12F683-I/MS PIC12 family 8-bit microcontroller embedded controller RISC architecture Flash program memory static RAM CMOS internal oscillator comparator with configurable hysteresis 8-bit timer 16-bit timer MSOP-8 surface-mount package MPLAB PIC programmer industrial control sensor threshold detection
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ