PIC16F527-E/P - 8-bit Flash MCU, 1.5KB, ADC+2xComp+2xAmp | Microchip
MPN: PIC16F527-E/P ✓ چالاکPIC16F527-E/P گشتی
A flash-based PIC microcontroller is a member of the PIC16 mid-range controller family (PIC16 -> 8-bit MCU -> microcontroller -> embedded semiconductor device). The PIC16 family uses a RISC Harvard architecture with a small instruction set, on-chip Flash program memory, integrated peripherals, and a wide operating-voltage range. PIC microcontrollers are commonly selected when designers need a low-cost, deterministic, easy-to-program MCU for cost-sensitive general-purpose applications and for systems that benefit from analog peripherals (ADC, comparators, op amps) integrated alongside the digital core.
Key features include 1024 words (1.5 KB) of Flash program memory, 68 bytes of RAM, 64 bytes of EEPROM data memory, eight 8-bit ADC channels with 10-bit (configurable) resolution, two analog comparators, two rail-to-rail op amps, an internal 8 MHz oscillator, and a wide operating-voltage range of 2.0 V to 5.5 V. The device supports in-circuit serial programming (ICSP) and is supported by the MPLAB X IDE and MPLAB XC8 C compiler.
The PIC16F527 uses a 14-bit instruction word and a 33-instruction set with single-instruction execution in 4 oscillator cycles (200 ns at 20 MHz / 8 MHz internal). Its integrated analog peripherals (ADC + 2 comparators + 2 op amps) make it a single-chip replacement for systems that would otherwise require a discrete op amp or comparator plus a separate MCU.
Typical applications include sensor signal conditioning, battery chargers, low-cost motor control, LED drivers, power-supply monitoring, and small appliances. The integrated op amps and comparators also support closed-loop analog control such as constant-current/constant-voltage battery charging, thermocouple amplification, and current sensing.
When designing with the PIC16F527, ensure that the on-chip op amp and comparator inputs are kept below the supply rails and that decoupling capacitors are placed within a few millimetres of the VDD pin. The 20-pin PDIP footprint is the largest of the PIC16F527 family variants and simplifies breadboarding and hand-soldered prototypes.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet, so an engineer can quickly determine whether the PIC16F527-E/P is the correct PIC16 MCU for their design.
جێگرەوەکانی جێگۆڕکێ بۆ PIC16F527-E/P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PIC16F527-E/P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Comparators, Operational Amplifiers, Package, Core Architecture, ADC.
PIC16F527-I/P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F527-E/JP
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F527-I/JP
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F527-E/SP
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16F527T-E/P
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16F527T-I/P
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
PIC16F527-E/P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Family | PIC16 (8-bit Flash MCU) |
| Core Architecture | PIC RISC, 14-bit instruction word |
| Program Memory (Flash) | 1.5 KB (1024 words) |
| RAM | 68 B |
| EEPROM Data Memory | 64 B |
| Maximum CPU Frequency | 20 MHz (8 MHz internal oscillator) |
| Instruction Execution Time | 200 ns at 20 MHz |
| Operating Voltage Range | 2.0 V to 5.5 V |
| مەودای پلەی گەرمیی کارکردن | -40 °C to +125 °C (E grade) |
| Comparators | 2 on-chip analog comparators |
| Operational Amplifiers | 2 on-chip op amps |
| پاکێج | 20-pin PDIP (P) through-hole |
| Programming Interface | ICSP (In-Circuit Serial Programming) |
| IDE / Compiler Support | MPLAB X IDE, MPLAB XC8 |
| دۆخی RoHS | Compliant |
ڕێکخستنی پینی PIC16F527-E/P
| پین 1 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
| پین 2 | RA5 — Digital I/O / analog input |
| پین 3 | RA4 — Digital I/O / analog input |
| پین 4 | RA3 — Digital I/O / analog input / MCLR |
| پین 5 | RC5 — Digital I/O |
| پین 6 | RC4 — Digital I/O |
| پین 7 | RC3 — Digital I/O |
| پین 8 | RC2 — Digital I/O |
| پین 9 | RC1 — Digital I/O |
| پین 10 | RC0 — Digital I/O |
| پین 11 | RB7 — Digital I/O |
| پین 12 | RB6 — Digital I/O / ICSPCLK |
| پین 13 | RB5 — Digital I/O |
| پین 14 | RB4 — Digital I/O |
| پین 15 | RB3 — Digital I/O |
| پین 16 | RB2 — Digital I/O |
| پین 17 | RB1 — Digital I/O |
| پین 18 | RB0 — Digital I/O / ICSPDAT |
| پین 19 | RA2 — Digital I/O / analog input |
| پین 20 | VSS — Ground reference |
بەکارهێنانە باوەکان
PIC16F527-E/P گونجاوە بۆ 6 بەکارھێنانs: Battery Charger / Power Supply Monitor, Sensor Signal Conditioning and Front-End, LED Lighting Driver and Dimming Control, Small Appliance and White-Goods Control, Automotive Body and Accessory Modules, Industrial Process and Loop Monitoring.
Battery Charger / Power Supply Monitor
The PIC16F527-E/P is well suited to single-cell Li-ion or NiMH battery chargers because its two integrated op amps and two comparators can implement constant-current and constant-voltage feedback loops, while the 8-bit ADC samples charge current and battery voltage in real time. The 1.5 KB Flash holds the CC/CV charge profile state machine and the 64-byte EEPROM stores calibration and end-of-charge parameters. Operating from 2.0 V to 5.5 V lets the charger run directly from a USB or 5 V adapter rail without a separate supervisor. Compared with a discrete op amp + comparator + MCU design, this part collapses three ICs into one and reduces both BOM cost and PCB area.
پێشنیارکراو
Sensor Signal Conditioning and Front-End
The PIC16F527-E/P's on-chip op amps amplify low-level sensor signals (thermocouples, photodiodes, strain gauges) before the ADC samples them, while the comparators generate threshold alarms without CPU intervention. The 8 MHz internal oscillator and 200 ns instruction execution support 1 kHz closed-loop sampling, which is sufficient for temperature, pressure and gas-sensor front-ends. The wide 2.0 V to 5.5 V supply range lets the same board run from a 3.3 V or 5 V sensor rail, and the extended -40 to +125 °C temperature grade (E suffix) supports outdoor and industrial deployments. This combination lets designers replace a discrete op amp + ADC + MCU chain with a single chip.
پێشنیارکراو
LED Lighting Driver and Dimming Control
Constant-current LED drivers benefit from the PIC16F527-E/P's integrated op amps (for current-sense amplification) and comparators (for PWM dimming and over-current protection). The MCU generates the PWM drive signal and adjusts duty cycle based on ADC readings, while the 1.5 KB Flash holds fade, dimming curve and thermal-foldback algorithms. The extended temperature grade (E suffix) is critical in enclosed luminaires where ambient can exceed 85 °C. Compared with a 555-timer-based dimmer, this part enables digital dimming curves, status LEDs and remote control without extra components.
پێشنیارکراو
Small Appliance and White-Goods Control
Coffee makers, blenders, irons, washing machines and similar small appliances need a low-cost MCU that drives a triac or relay, reads a temperature or level sensor, and times a cycle - exactly what the PIC16F527-E/P provides with its on-chip op amps and comparators. The 20-pin PDIP package is easy to hand-solder and repair in appliance service environments. The extended temperature grade supports the enclosed, hot compartments found in many appliances. Compared with pure-hardware analog timer designs, this part adds programmability, fault diagnostics and user-interface flexibility without raising the BOM by more than a few tens of cents.
پێشنیارکراو
Automotive Body and Accessory Modules
Inside the cabin, the PIC16F527-E/P's extended temperature grade (-40 to +125 °C) and integrated analog peripherals support body-control modules such as seat heaters, mirror adjusters, interior lighting, and accessory timers. The op amp reads a thermistor for seat-heater closed-loop control, while the comparator generates over-current trips on LED strings. Operating from a 5 V regulator on the automotive 12 V bus, the MCU's wide supply tolerance handles crank and load-dump transients when paired with proper external protection. Designers choose the -E grade specifically because cabin temperatures and under-hood-adjacent enclosures can exceed 85 °C.
پێشنیارکراو
Industrial Process and Loop Monitoring
Process-control modules that monitor 4-20 mA loops, sense tank levels or detect threshold events are well served by the PIC16F527-E/P's two comparators (for window detection) and on-chip op amps (for transducer excitation and amplification). The 8-bit ADC samples the conditioned signal, and the EEPROM retains calibration constants across power cycles. The 20-pin PDIP and extended temperature grade simplify deployment in factory-floor enclosures where ambient can be high. Compared with a pure analog signal conditioner, this part adds local decision-making, fault logging and a digital interface without a separate processor.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ PIC16F527-E/P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | PIC16F527-I/P | PIC16F527-E/JP | PIC16F527-I/JP | PIC16F527-E/SP | PIC16F527T-E/P | PIC16F527T-I/P |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | PDIP-20 | PDIP-20 (same) | PDIP-20 (same) | PDIP-20 (same) | PDIP-20 (same) | PDIP-20 (same) | PDIP-20 (same) |
| Temperature Grade | Extended -40 to +125 C | Industrial -40 to +85 C | Extended -40 to +125 C | Industrial -40 to +85 C | Extended -40 to +125 C | Extended -40 to +125 C | Industrial -40 to +85 C |
| Program Memory (Flash) | 1.5 KB | 1.5 KB | 1.5 KB | 1.5 KB | 1.5 KB | 1.5 KB | 1.5 KB |
| On-chip Op Amps | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Comparators | 2 | 2 | 2 | 2 | 2 | 2 | 2 |
| Operating Voltage | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| Pin Compatibility | 20-pin PDIP base | Pin-to-pin (same die) | Pin-to-pin (same die) | Pin-to-pin (same die) | Pin-to-pin (same die) | Pin-to-pin (same die) | Pin-to-pin (same die) |
| Packing Format | Tube | Tube | Tube (JP) | Tube (JP) | Tube (SP) | Tape & Reel | Tape & Reel |
جیاکەرەوە سەرەکییەکان
- Same 20-pin PDIP footprint across temperature grades and packing formats (بەراورد بەPIC16F527-I/P)
- PIC16F527-E/JP option keeps identical die for high-reliability tube feeding (بەراورد بەPIC16F527-E/JP)
- Tape-and-reel option for automated SMT-compatible assembly lines (بەراورد بەPIC16F527T-E/P)
تێبینییەکانی دیزاین
Place a 100 nF decoupling capacitor within 5 mm of the VDD pin (pin 1) and a bulk 10 uF capacitor near the PIC16F527-E/P. The wide 2.0 V to 5.5 V supply range lets you share a 3.3 V or 5 V rail with analog circuitry, but ensure the op amp output stays within the supply rails to avoid saturation; add a small series resistor at the op amp output if driving long PCB traces to capacitive loads.
Keep analog input traces (ADC ANx, comparator and op amp inputs) short and routed away from digital switching traces such as PWM outputs and ICSP clock lines. Use a ground pour on the top layer under the IC to provide a low-impedance return for both digital and analog currents, and route the VDD trace wide enough to handle the brief inrush when the op amps drive heavy loads.
Do not exceed 5.5 V on VDD - the PIC16F527-E/P is not 5 V tolerant above the spec limit. Always configure unused I/O pins as outputs (not inputs) to avoid floating-pin current. When using the on-chip op amps as unity-gain buffers, leave the inverting input tied to the output or a defined voltage; an open inverting input can drift and cause unexpected supply current. Finally, ensure ICSPDAT and ICSPCLK (RB0/RB6) are not driven by external circuitry during in-circuit programming.
زانیاری پابەندبوون
RoHS compliant per Microchip product page. Not AEC-Q100 qualified; the -E extended temperature grade supports -40 to +125 C but is not automotive-qualified.