PIC16F610-I/P - 8-Bit 20MHz Flash MCU | Microchip Technology
MPN: PIC16F610-I/P ✓ چالاکPIC16F610-I/P گشتی
A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, and peripherals onto one IC. The PIC16F610 belongs to the PIC16 family, a group of 8-bit CMOS microcontrollers intended for compact control tasks. Its flash-based program memory supports device programming and reprogramming, while its small SRAM supports working variables and control-state information. In system architecture terms, a microcontroller belongs to the embedded-processing and semiconductor hierarchy.
The verified device information identifies an operating speed of 20 MHz, 1.75 KB of flash program memory, 1K × 14-word organization, 72 bytes of RAM, and a 14-pin PDIP package. The -I portion identifies the industrial-temperature grade, while /P identifies the through-hole PDIP package. These details make the PIC16F610-I/P appropriate where a modest instruction-processing capacity, embedded program storage, and a readily solderable package are more important than high peripheral integration or large memory capacity.
Typical uses include simple sequential controllers, laboratory teaching boards, embedded timers, LED indicators, switch interfaces, and compact automation modules. The 20 MHz maximum clock provides a clear timing target for firmware loops and peripherals, while the 72-byte RAM capacity favors short control routines and small working datasets. Designers should confirm the complete pinout, electrical limits, peripheral set, and clock configuration in the Microchip data sheet before committing a new PCB.
A principal design consideration is the comparatively small memory budget. Compact state machines and interrupt-driven routines are appropriate, whereas large buffers or complex protocol stacks may exceed the available RAM and flash. Decoupling, oscillator selection, programming-tool compatibility, and I/O voltage limits must also be checked against the manufacturer data sheet rather than inferred from a distributor category description.
This page combines verified manufacturer and distributor information with package-aware selection guidance, replacement limitations, and practical design considerations. It highlights the PIC16F610-I/P's 20 MHz speed, 1.75 KB flash, 72-byte RAM, and 14-pin PDIP implementation while distinguishing verified facts from parameters that still require engineering review.
جێگرەوەکانی جێگۆڕکێ بۆ PIC16F610-I/P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ PIC16F610-I/P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Timers, Comparators, Mounting Type, ADC.
PIC16F616-I/P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →PIC16F610-I/P زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Device Type | 8-bit CMOS flash-based microcontroller |
| زۆرترین فرێکوێنسیی کاتژمێر | 20 MHz |
| Program Memory Type | Flash |
| Flash Memory Capacity | 1.75 KB |
| Program Memory Organization | 1K × 14 words |
| Data Memory Capacity | 72 bytes RAM |
| Package Type | 14-pin PDIP |
| Temperature Grade | I-grade industrial temperature grade; range not stated in supplied excerpts |
| Instruction Set Width | 8-bit |
| شێوازی دامەزراندن | Through-hole |
ڕێنمایی ڕێکخستنی پینی PIC16F610-I/P 14-pin pdip
ڕێکخستنی پین بۆ PIC16F610-I/P (پاکێجی 14-pin pdip). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ PIC16F610-I/P.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
PIC16F610-I/P گونجاوە بۆ 6 بەکارھێنانs: Education and MCU Training, Simple Sequential Control, LED and Indicator Control, Compact Timer and Counter Module, Small Embedded Control Board, Switch and Sensor Interface Hub.
Education and MCU Training
The PIC16F610-I/P fits introductory microcontroller laboratories because it combines an 8-bit architecture with 20 MHz operation, 1.75 KB of flash, and 72 bytes of RAM in an easy-to-handle 14-pin PDIP package. Students can connect LEDs, switches, and simple sensors while learning instruction sequencing, interrupt structure, and memory organization without using a complex high-pin-count device. Its through-hole format is particularly convenient on solderless breadboards and perforated prototyping boards. According to the Microchip manufacturer data sheet, flash memory supports programmed or reprogrammable experiments. The principal limitation is the 72-byte RAM budget, so exercises should use small state tables and modest buffers.
پێشنیارکراو
Simple Sequential Control
PIC16F610-I/P is appropriate for compact sequential controllers that coordinate relays, indicators, counters, and discrete sensors. Its verified 20 MHz maximum clock provides useful timing headroom for deterministic state-machine routines, while 1.75 KB of flash can hold a moderate amount of control code and 72 bytes of RAM can hold current state variables. The 14-pin PDIP package also simplifies prototype rework in industrial-control training rigs. According to the Microchip product page, the device is in production. Before deployment, verify the exact I/O pin map, required pull-up or pull-down components, timing margins, and required safety isolation.
پێشنیارکراو
LED and Indicator Control
The PIC16F610-I/P can serve as the controller in an LED panel, status annunciator, or counter display because an 8-bit MCU can scan indicators and implement timing patterns within a compact footprint. Its 20 MHz clock supports responsive multiplexing routines, while the flash-based 1.75 KB memory simplifies firmware updates during development. The 14-pin PDIP construction is useful for hand-built demonstration and educational boards where a socket may be preferred over a fine-pitch surface-mount package. According to the Microchip manufacturer data sheet, the MCU is a CMOS flash-based device. Designers must still confirm available I/O count, drive-current limits, indicator current requirements, and whether a driver transistor or resistor network is necessary.
پێشنیارکراو
Compact Timer and Counter Module
PIC16F610-I/P is well matched to stand-alone timers, event counters, and small test fixtures where an embedded controller replaces discrete timing logic. The verified 20 MHz operating speed permits more frequent polling and timing calculations than a slow low-cost controller, although the 72-byte RAM still requires economical state management. Its flash-based program memory allows firmware revision in a through-hole prototype. According to Microchip's PIC16F610/16HV610/PIC16F616/16HV616 manufacturer data sheet, this is an 8-bit CMOS PIC microcontroller. Final implementation should verify oscillator options, timer availability, interrupt sources, input tolerance, and calibration requirements.
پێشنیارکراو
Small Embedded Control Board
The PIC16F610-I/P can anchor a small automation board that coordinates switches, alarms, and a limited set of actuators because it integrates program memory, data memory, and processing in one 14-pin DIP device. Its 1.75 KB flash capacity suits concise supervisory logic, and the 20 MHz clock provides margin for event handling. The PDIP package is advantageous for prototypes, legacy industrial test equipment, and boards assembled through holes. According to the verified Microchip product-page result, PIC16F610 is in production. Before using it as a board-level controller, confirm the exact peripheral inventory, I/O electrical limits, watchdog behavior, supply requirements, and environmental ratings.
پێشنیارکراو
Switch and Sensor Interface Hub
PIC16F610-I/P is suitable for a compact interface hub that reads switches or simple digital sensors and converts their states into system actions. The verified 8-bit architecture, 20 MHz clock, 1.75 KB flash, and 72-byte RAM are adequate for debouncing, state tracking, and event reporting in a deliberately small design. Its 14-pin PDIP package allows straightforward socketed prototyping and field replacement. According to the Microchip manufacturer data sheet, the device is a flash-based CMOS PIC16 microcontroller. Verify the complete pin assignment, available digital I/O, pull-up requirements, input voltage tolerance, and any analog or comparator functions against the application requirements.
پێشنیارکراو
داتای سەرچاوەی ئەندازیاری بۆ PIC16F610-I/P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | PIC16F616-I/P |
|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP - same package |
| Brand | Microchip Technology | Microchip Technology |
جیاکەرەوە سەرەکییەکان
- Verified 20 MHz operating speed (بەراورد بەPIC16F616-I/P)
- Documented memory configuration (بەراورد بەPIC16F616-I/P)
- Production-status confirmation (بەراورد بەPIC16F616-I/P)
تێبینییەکانی دیزاین
Confirm the exact VDD range, I/O limits, and power-consumption curves in the Microchip manufacturer data sheet before adding decoupling or selecting a supply. The verified 20 MHz frequency does not establish the permitted operating voltage. Place the required input and output capacitors adjacent to the corresponding pins, use short supply paths, and keep switching-current return loops away from sensitive signal traces. Because the supplied excerpts do not identify the decoupling values, do not guess capacitor sizes or the number of required rails.
Design the 14-pin PDIP footprint from the official package drawing rather than the distributor thumbnail. Verify pin 1 orientation, row spacing, drill diameter, lead pitch, maximum body dimensions, and soldering clearances. The supplied results confirm a 14-pin PDIP package but do not provide a complete mechanical drawing or numbered signal map, so both footprint geometry and electrical pin assignments must be checked against the manufacturer data sheet before PCB release.
Do not assume that a related family member is firmware- and peripheral-compatible merely because it has the same package. PIC16F616-I/P is a verified 14-pin candidate, but its exact flash, RAM, I/O, and peripheral differences are not supplied. Create a register-by-register and memory-map comparison, recompile the firmware, and test reset, interrupts, timers, I/O, and programming before substitution. Also avoid using the quoted 72-byte RAM as though it were the entire available data workspace.
زانیاری پابەندبوون
The supplied excerpts establish the industrial-temperature grade and in-production status but do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations. These fields remain unknown rather than being inferred from the manufacturer or package.