Texas Instruments

SN65HVD11P - 3.3V 10Mbps RS-485 Transceiver | Texas Instruments

MPN: SN65HVD11P ✓ چالاک
3.3 V Vdss 1 Package
MOQ: 1 |

SN65HVD11P گشتی

The Texas Instruments SN65HVD11P is a 3.3 V differential RS-485 and RS-422 transceiver rated for signaling rates up to 10 Mbps in an 8-pin PDIP package. It combines a differential line driver, differential receiver, and 3-state driver control in one interface IC for balanced industrial communication buses. The device operates from a single 3.3 V supply and supports the -40°C to +85°C industrial temperature range.

An RS-485 transceiver is a physical-layer interface IC that converts logic-level signals into balanced differential bus signals and receives differential signals back into logic levels. Differential signaling belongs to the RS-422 and RS-485 interface family, where complementary signal paths improve noise immunity and allow reliable communication over longer cable runs than single-ended interfaces. The SN65HVD11 family is designed for balanced transmission lines and is identified by Texas Instruments as meeting or exceeding ANSI TIA/EIA-485-A and ISO 8482:1993 requirements.

Key features include a 3.3 V supply, operation to 10 Mbps, an eight-pin PDIP package, and bus-pin ESD protection exceeding 16 kV HBM. The 3-state driver output allows the transmitter to be disabled for receiver-only or multidrop bus operation. Differential signaling rejects common-mode noise coupled equally into both bus conductors, while the receiver converts the voltage difference between those conductors into a valid logic output.

The SN65HVD11 architecture combines a differential line driver with a differential input receiver on a single 3.3 V power supply. Its receiver and driver functions support point-to-point links as well as shared balanced networks. Because the driver can enter a high-impedance state, multiple nodes can share the bus when only one transmitter is active at a time. The family’s 10 Mbps capability is suitable for factory automation, instrumentation, and other balanced industrial data links operating above the slower rates commonly used by isolated field buses.

Typical applications include industrial sensor interfaces, programmable logic controller communication, test and measurement equipment, building-control subsystems, and embedded data acquisition. The device is particularly useful when a compact system needs both transmit and receive functions without adding separate line-driver and line-receiver packages. Its through-hole PDIP package also supports prototype boards and designs where inspection or rework is easier than with a fine-pitch surface-mount package.

Designers should place the transceiver close to the bus connector and route the differential pair as a controlled-impedance pair with matched spacing and symmetric termination geometry. Keep the ground reference close to the cable shield, and avoid adding excessive stub length to multidrop branches. Verify the logic thresholds, bus loading, termination strategy, and common-mode range before committing the board layout.

This page organizes the SN65HVD11P electrical, package, application, replacement, and sourcing information into an engineering-focused guide. It also highlights the benefits and limits of same-footprint family alternatives so designers can distinguish a physical pin-compatible option from one that satisfies the complete operating profile.

جێگرەوەکانی جێگۆڕکێ بۆ SN65HVD11P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN65HVD11P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Driver Output Type, Mounting Type, Bus-Pin ESD Protection.

Texas Instruments
Package: 8-pin PDIP (P)
Product Type: Half-duplex RS-485 transceiver
Driver Output Type: Three-state differential line driver
بەراوردکردن لەگەڵ SN65HVD11P →
Texas Instruments
Package: 8-PDIP
Product Type: Differential bus transceiver
Driver Output Type: Three-state differential output
بەراوردکردن لەگەڵ SN65HVD11P →
MaxLinear
Package: 8-SOIC
Product Type: RS-485/RS-422 half-duplex transceiver
Mounting Type: Surface mount
بەراوردکردن لەگەڵ SN65HVD11P →

SN65HVD11PE4

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin PDIP
Same SN65HVD11 function and 8-pin PDIP footprint; green-environment version designation, with no quantified electrical-rate difference stated.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SN65HVD10P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin PDIP
Half-duplex RS-485 transceiver · 3.3 V · 32 Mbps · RS-485 · Half-duplex · Three-state differential line driver · Differential line receiver · 1/8 unit load, up to 256 nodes

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN75HVD10P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin PDIP
Same 3.3 V eight-pin bus-transceiver footprint; the HVD10 variant differs in signaling-rate and fail-safe behavior.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SN65HVD12P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 8-pin PDIP
Differential bus transceiver · 3.3 V · 1 Mbps · RS-422 and RS-485 · Three-state differential output · Differential input line receiver · Half-duplex · 8-PDIP

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN75HVD11P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 8-pin PDIP
Same 3.3 V eight-pin HVD11 family footprint, but the HVD75 variant has different receiver fail-safe behavior.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SN65HVD11P تایبەتمەندییەکان

Product Type Differential transceiver
ڤۆڵتیەی دابینکردن 3.3 V
Supported Interfaces RS-485 and RS-422
Maximum Signaling Rate 10 Mbps
Driver Output Type 3-state differential line driver
Receiver Type Differential input line receiver
Number of Transceivers per Package 1
پاکێج 8-pin PDIP, 7.62 mm pitch
ژمارەی پین 8 pins
جۆری دامەزراندن Through-hole
مەودای پلەی گەرمیی کارکردن -40°C to +85°C
Bus-Pin ESD Protection Exceeds 16 kV HBM
RS-485 Compliance Meets or exceeds ANSI TIA/EIA-485-A
RS-485 Compliance Meets or exceeds ISO 8482:1993
Transmission Line Type Balanced transmission line

ڕێنمایی ڕێکخستنی پینی SN65HVD11P 8-pin pdip, 7.62 mm pitch

ڕێکخستنی پین بۆ SN65HVD11P (پاکێجی 8-pin pdip, 7.62 mm pitch). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 8-pin pdip, 7.62 mm pitch بۆ SN65HVD11P

هیچ داتای وردی پینئاوت بەردەست نییە بۆ SN65HVD11P.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

SN65HVD11P گونجاوە بۆ 6 بەکارھێنانs: Industrial Sensor Networking, PLC and Controller Communication, Test and Measurement Instrumentation, Building Control and HVAC Networks, Embedded Data Acquisition, Robotics and Motor-Control Systems.

🏭

Industrial Sensor Networking

The SN65HVD11P fits industrial sensor networks that distribute measurements over balanced RS-485 wiring. Its differential driver and receiver reject common-mode noise, while the 10 Mbps signaling capability supports factory data paths that are faster than many legacy 9600-baud or 115.2-kbaud sensor links. The 3.3 V supply is suitable for embedded acquisition equipment, and the -40°C to +85°C range covers industrial factory environments. Place the transceiver near the connector, route A and B as a matched pair, and apply termination only where the topology requires it. Because the driver is 3-state capable, a multidrop bus can support multiple nodes when only one transmitter is enabled at a time.

⚡

PLC and Controller Communication

The SN65HVD11P is useful in PLC modules, remote I/O controllers, and programmable logic controller communication boards that use RS-485. Combining the transmitter and receiver in one 8-pin PDIP reduces the number of interface components needed for bidirectional bus nodes. The 3.3 V operating supply aligns with modern controller logic, and the 10 Mbps capability allows a design to accommodate faster equipment links. Verify that the bus voltage, common-mode range, grounding method, and termination plan match the connected controller. The transmitter should be disabled while the node listens to prevent contention on a multidrop bus.

🔧

Test and Measurement Instrumentation

The SN65HVD11P can connect laboratory instruments, automated test equipment, and data-acquisition modules to a balanced control bus. Differential reception helps reject interference that may be present around motors, relay contacts, and switching equipment, while the 10 Mbps rate supports rapid command and status transfer. The 3.3 V supply simplifies integration with low-voltage control logic, and the PDIP package is convenient for laboratory prototype boards where component replacement is likely. Keep the transceiver and protection network close to the external connector, use a controlled-impedance pair, and keep return paths short so transient energy does not propagate into the instrument’s sensitive analog sections.

🏠

Building Control and HVAC Networks

The SN65HVD11P supports balanced communication links in building-control panels, HVAC controllers, room sensors, and remote actuator modules. Its 3.3 V supply works well with embedded logic, and the transceiver’s differential signaling helps maintain data integrity when control wiring runs near lighting, motors, and switching loads. The -40°C to +85°C rating accommodates industrial equipment environments, although the final enclosure and system thermal design determine the allowable ambient temperature. Use consistent bus topology and avoid long unterminated branches, because those can produce reflections and reduce the reliability of a low-speed building-control network.

🖥️

Embedded Data Acquisition

The SN65HVD11P fits embedded data-acquisition systems that exchange commands and samples between a controller and remote analog or digital I/O modules. Combining differential transmit and receive functions in an 8-pin PDIP supports compact through-hole designs and straightforward prototype rework. Its 10 Mbps signaling rate is sufficient for many high-speed industrial links, although actual range depends on cable type, data rate, topology, and termination. Place a suitable bus protection device at the connector, provide a low-impedance ground reference, and separate the transceiver from high-energy switching stages to reduce the amount of surge energy that reaches the IC.

🤖

Robotics and Motor-Control Systems

The SN65HVD11P can connect robot controllers, motor-drive modules, and position sensors through a balanced RS-485 command bus. Differential signaling is advantageous in motor environments because it improves noise immunity relative to a single-ended interface. The 3.3 V supply can support low-voltage embedded control, and the 10 Mbps rate provides ample margin for command and status packets. Keep the bus connection physically separate from motor phases and use a protective network at the exposed cable interface. The transceiver should be enabled only while transmitting so that multiple nodes can share the bus without active driver contention.

کورتەی بەرهەمە پێشنیارکراوەکان

SN65HVD12P Texas Instruments بەکارهێنراوە لە: Industrial Sensor Networking, Building Control and HVAC Networks SN75HVD11P Same-family transceiver with different fail-safe behavior بەکارهێنراوە لە: Industrial Sensor Networking, Robotics and Motor-Control Systems SN65HVD10P Texas Instruments بەکارهێنراوە لە: PLC and Controller Communication, Robotics and Motor-Control Systems SN75HVD10P Same-package alternate fail-safe family option بەکارهێنراوە لە: PLC and Controller Communication SP485EMN-L/TR MaxLinear بەکارهێنراوە لە: Test and Measurement Instrumentation, Embedded Data Acquisition ADM485JNZ Analog Devices بەکارهێنراوە لە: Test and Measurement Instrumentation, Embedded Data Acquisition SN65HVD11PE4 Same SN65HVD11 electrical configuration in a PDIP package بەکارهێنراوە لە: Building Control and HVAC Networks
What is the SN65HVD11P?
The SN65HVD11P is a Texas Instruments single-channel differential transceiver that combines a 3-state RS-485 line driver with a differential receiver. It operates from a 3.3 V supply, supports signaling rates up to 10 Mbps, and is packaged in an 8-pin PDIP. According to the manufacturer product page and SNx5HVD1x family datasheet, it is intended for balanced RS-485 and RS-422 communication lines.
What is the operating voltage of SN65HVD11P?
The SN65HVD11P operates from a single 3.3 V supply. Texas Instruments describes the SN65HVD11 as a 3.3 V differential transceiver, and the family datasheet identifies the same 3.3 V architecture across the SN65HVD10, SN65HVD11, SN65HVD12, SN75HVD10, SN75HVD11, and SN75HVD12 devices. The family combines a differential transmitter and receiver without requiring a separate supply rail.
What is the maximum data rate of SN65HVD11P?
The SN65HVD11P supports signaling rates up to 10 Mbps. The 10 Mbps figure identifies the maximum signal rate supported by this device for balanced bus communication. Actual application throughput depends on cable length, termination, topology, clocking, protocol overhead, and signal integrity, so a 10 Mbps capable link does not guarantee the same practical bus distance at the highest rate.
Is SN65HVD11P compatible with RS-485 and RS-422?
Yes. The SN65HVD11P is designed for differential RS-485 and RS-422 interfaces. Texas Instruments states that the SNx5HVD1x family is intended for balanced transmission lines and meets or exceeds ANSI TIA/EIA-485-A and ISO 8482:1993 requirements. Its 3-state driver also allows multiple nodes to share a bus when transmitters are individually controlled.
Where can I download the SN65HVD11P datasheet PDF?
The official SN65HVD11P datasheet is available from Texas Instruments through the SNx5HVD1x family datasheet link at https://www.ti.com/lit/gpn/SN65HVD11. The manufacturer product page for SN65HVD11 is at https://www.ti.com/product/SN65HVD11. Use the family datasheet for the complete pin descriptions, electrical characteristics, timing diagrams, and application guidance.
Where can I find the SN65HVD11P pinout?
The SN65HVD11P pin assignment is defined in the pin-configuration section of the Texas Instruments SNx5HVD1x family datasheet at https://www.ti.com/lit/gpn/SN65HVD11. The device uses an 8-pin PDIP configuration with numbered pins for the differential bus connections, receiver logic output, driver data input, driver enable, receiver enable, and supply connections. Confirm every signal against the datasheet before assigning PCB tracks.
What are the key specifications of SN65HVD11P that engineers should know?
The principal SN65HVD11P specifications are a 3.3 V supply, operation up to 10 Mbps, an 8-pin PDIP package, and a -40°C to +85°C operating range. Texas Instruments also identifies bus-pin ESD protection exceeding 16 kV HBM. The device combines a 3-state differential driver and a differential receiver in one package, making it suitable for compact balanced-bus interface designs.
What can replace SN65HVD11P?
The closest same-footprint choices identified for SN65HVD11P are SN65HVD11PE4, SN65HVD10P, SN75HVD10P, SN65HVD12P, and SN75HVD11P. Each uses the same 8-pin PDIP family arrangement, but the HVD10 and HVD12 devices have different speed and fail-safe characteristics. Confirm the complete datasheet specifications and bus requirements before treating any alternative as a functional substitute.
Is SN65HVD11P the same as SN65HVD12P?
No, although SN65HVD12P is a pin-compatible member of the same 8-pin PDIP transceiver family. The two devices are positioned for different signaling-rate requirements, with SN65HVD12P offering a higher maximum data rate than SN65HVD11P. According to the Texas Instruments family information, both provide a 3.3 V differential transmitter and receiver, but maximum rate and related electrical characteristics must be checked for the target bus.
When should I choose SN65HVD11P over SN65HVD10P or SN65HVD12P?
Choose SN65HVD11P when the design needs the 10 Mbps signaling capability of the HVD11 family in an 8-pin PDIP package. Select SN65HVD10P only after confirming that its speed and fail-safe behavior meet the application, and choose SN65HVD12P when its faster signaling capability is required. The choice should also account for receiver fail-safe behavior, cable length, node count, and component availability.
Is SN65HVD11P suitable for industrial automation and sensor networks?
Yes. The SN65HVD11P suits industrial automation and sensor-network interfaces that use balanced wiring and require reliable differential signaling. Its 3.3 V operation supports low-voltage embedded systems, while the 10 Mbps rate and -40°C to +85°C range provide useful design headroom. The transceiver does not replace isolation, surge protection, or application-specific safety measures.
What is the best cross-brand equivalent for SN65HVD11P?
A cross-brand equivalent cannot be confirmed from the available manufacturer and distributor records because they do not identify a competing 8-pin PDIP transceiver with verified pin compatibility and equivalent electrical ratings. The supported same-brand alternatives remain the more defensible starting point, but any cross-brand device should be checked for supply voltage, maximum signaling rate, receiver thresholds, fail-safe behavior, ESD rating, and exact pin arrangement.
Where can I buy SN65HVD11P online?
Use the Request a Quote form on this page to request SN65HVD11P availability, current lead time, and a quotation for the required quantity. The manufacturer’s part-details page identifies SN65HVD11P as an 8-pin PDIP device rated from -40°C to +85°C. Supply status can change, so confirm the requested quantity, packaging, and date-code requirements when placing the order.
What is the price of SN65HVD11P?
Current SN65HVD11P pricing is generated through the Request a Quote form on this page because market prices, quantity breaks, and availability may change. The structured pricing fields are intentionally kept empty unless a current listing publishes an explicit quantity and price for this exact MPN. Submit the required quantity and packaging details to obtain a current quotation directly through the page.
What is the lead time for SN65HVD11P?
The current SN65HVD11P lead time should be requested through the Request a Quote form on this page. Texas Instruments lists SN65HVD11P as an orderable 8-pin PDIP part, but no fixed factory lead time is stated in the current manufacturer and distributor records. Provide the required quantity, date-code preference, and shipping destination so the quotation can reflect the actual supply condition.

داتای سەرچاوەی ئەندازیاری بۆ SN65HVD11P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose SN65HVD11P when the design needs a compact 3.3 V RS-485/RS-422 interface in an 8-pin PDIP package, supports signaling rates up to 10 Mbps, and operates across the -40°C to +85°C range. Select SN65HVD11PE4 when the same electrical configuration is needed with the manufacturer’s green-environment ordering designation. Consider SN65HVD10P or SN75HVD10P when their specific rate and fail-safe characteristics better match the bus, and select SN65HVD12P when its higher-speed profile is necessary. Use SN75HVD11P when its distinct fail-safe behavior is required. For every option, verify the exact pin description, common-mode range, receiver thresholds, ESD rating, termination requirements, and cable-length limit in the manufacturer datasheet before production release.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە SN65HVD11PE4 SN65HVD10P SN75HVD10P SN65HVD12P SN75HVD11P
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Supply Voltage 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V 3.3 V
Transceiver Function 3-state differential driver and differential receiver 3-state differential driver and differential receiver 3-state differential driver and differential receiver 3-state differential driver and differential receiver 3-state differential driver and differential receiver 3-state differential driver and differential receiver
RS-485 Standards Support ANSI TIA/EIA-485-A and ISO 8482:1993 ANSI TIA/EIA-485-A and ISO 8482:1993 ANSI TIA/EIA-485-A and ISO 8482:1993 ANSI TIA/EIA-485-A and ISO 8482:1993 ANSI TIA/EIA-485-A and ISO 8482:1993 ANSI TIA/EIA-485-A and ISO 8482:1993
Price Tier Request a Quote Request a Quote Request a Quote Request a Quote Request a Quote Request a Quote

جیاکەرەوە سەرەکییەکان

  • Combines transmitter and receiver in one 8-pin PDIP (بەراورد بەSN65HVD11PE4)
  • Standard HVD11 receiver behavior (بەراورد بەSN75HVD11P)
  • 10 Mbps signaling rate (بەراورد بەSN65HVD10P)
  • Industrial temperature coverage (بەراورد بەSN65HVD12P)

تێبینییەکانی دیزاین

Route the A and B conductors as a closely coupled differential pair with substantially uniform spacing and length. Place the transceiver close to the connector and termination or protection components so transient energy is diverted before reaching the IC. Avoid switching-current paths beneath the bus pair, and provide a short ground reference alongside the cable connection.

Do not enable multiple drivers on the same bus at the same time. The SN65HVD11P has a 3-state output, so software and hardware logic should mutually control the driver-enable and receiver-enable functions for multidrop networks. Also verify the connector's A/B polarity, because reversing the pair inverts the bus signal and can prevent communication.

Termination and biasing must be calculated for the actual topology. Place termination only at appropriate physical ends of the trunk, use suitable fail-safe biasing where required, and avoid long stubs. The 10 Mbps capability does not define a universal cable length: rise time, cable attenuation, topology, grounding, and common-mode noise determine the usable distance.

Keep the differential bus away from motors, relay contacts, switching-power nodes, and high-current return paths. Use a continuous reference plane where practical and place external protection at the connector. The transceiver's differential receiver improves common-mode rejection, but proper layout is still necessary to prevent radiated emissions and conducted noise from affecting adjacent circuitry.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The family datasheet identifies ANSI TIA/EIA-485-A and ISO 8482:1993 support, but the current product records do not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The SN65HVD11P is not identified as an AEC-Q100-qualified automotive variant.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

SN65HVD11P datasheet SN65HVD11P datasheet pdf SN65HVD11P pinout SN65HVD11P specifications SN65HVD11P RS-485 transceiver SN65HVD11P 10 Mbps SN65HVD11P 3.3V SN65HVD11P PDIP SN65HVD11P replacement SN65HVD11P equivalent SN65HVD11P vs SN65HVD12P SN65HVD11P price SN65HVD11P stock Texas Instruments SN65HVD11P

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments SN65HVD11P SN65HVD11 SN65HVD11PE4 SN65HVD10P SN75HVD10P SN65HVD12P SN75HVD11P RS-485 RS-422 differential transceiver differential line driver differential line receiver 3-state driver balanced transmission line common-mode rejection signaling rate 10 Mbps 3.3 V ANSI TIA/EIA-485-A ISO 8482:1993 PDIP-8 surface-mount through-hole industrial automation
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ