Texas Instruments

SN65HVD21P - Extended Common-Mode RS-485 Transceiver | Texas Instruments

MPN: SN65HVD21P ✓ چالاک
RS-485, RS-422 Rds(on) PDIP (P), 8 pins Package
MOQ: 1 |

SN65HVD21P گشتی

The Texas Instruments SN65HVD21P is an extended common-mode RS-485 and RS-422 transceiver containing one driver and one receiver in a single 8-pin PDIP (P) through-hole package. It is specified as an extended common-mode RS-485 transceiver, which is the key feature that distinguishes it from standard RS-485 parts whose receivers saturate when ground-potential differences between nodes appear on long cables. The SN65HVD21P is used wherever a half-duplex differential bus must tolerate wiring faults, ground offsets and unbalanced cable runs.

An RS-485 transceiver is a type of interface IC that bridges a logic-level UART or SPI port and a balanced, differential bus. The differential signalling rejects common-mode noise, so the bus keeps working in electrically noisy environments such as factory floors, HVAC plants, motor drives and utility metering cabinets. The SN65HVD21P belongs to the hierarchy: transceiver -> differential line driver and receiver -> interface IC -> integrated circuit -> semiconductor.

Because the driver and receiver share one package, the same device supports half-duplex point-to-point links as well as multidrop configurations where up to multiple unit-load nodes tap onto one pair of wires. The three control pins (driver enable, receiver enable and driver input) let a host microcontroller decide which direction the bus drives, while the receiver output returns logic-level data to the host. The PDIP package keeps the device compatible with through-hole assembly, prototyping boards and legacy industrial control boards.

Typical deployments include industrial RS-485 multidrop sensor buses, building and HVAC controller networks, industrial motor drive and encoder feedback links, utility and energy metering terminals, and long-distance instrumentation links to remote transducer heads. Because the transceiver is a half-duplex device, the design must allow the bus to turn around between transmit and receive windows.

The main design consideration is termination and biasing. The SN65HVD21P works correctly on an unterminated short cable, but long or high-speed runs need a termination resistor at each far end and a fail-safe bias network so the idle state is defined. Keep the differential pair tightly coupled, route it over a continuous ground plane, and connect the transceiver ground to the board ground with a short, low-inductance path.

This page combines the manufacturer part detail, distributor availability, drop-in replacement options in the same 8-pin PDIP footprint, and practical bus-design guidance so engineers can evaluate the SN65HVD21P without hunting across several separate documents.

جێگرەوەکانی جێگۆڕکێ بۆ SN65HVD21P — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN65HVD21P (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Transceiver Configuration, Mounting Type, Data Rate.

Analog Devices
Transceiver Configuration: 1 transmitter and 1 receiver
بەراوردکردن لەگەڵ SN65HVD21P →
Analog Devices
Package: 8-pin PDIP
Product Type: RS-485/RS-422 transceiver
بەراوردکردن لەگەڵ SN65HVD21P →
Texas Instruments
Package: PDIP-8, 8 pins
Product Type: Extended common-mode RS-485 transceiver
Data Rate: 500kbps
بەراوردکردن لەگەڵ SN65HVD21P →
Texas Instruments
Product Type: RS-422/RS-485 transceiver
Transceiver Configuration: 1/1 transceiver, half-duplex
بەراوردکردن لەگەڵ SN65HVD21P →
MaxLinear
Package: 8-pin SOIC
Product Type: Half-duplex RS-422/RS-485 transceiver
Mounting Type: Surface mount
بەراوردکردن لەگەڵ SN65HVD21P →

SN65HVD22P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 PDIP-8 (P)
Extended common-mode RS-485 transceiver · 500kbps · -20V to 25V · 1 driver · 1 receiver · Half-duplex · TIA/EIA-485-A, RS-485, RS-422 · High ESD protection

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD23P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
Texas Instruments
📦 PDIP-8 (P)
RS-422/RS-485 transceiver · 1/1 transceiver, half-duplex · 25 Mbps · -20 V to 25 V · TIA/EIA-485-A · Up to 256 nodes · Over 16 kV HBM · Yes

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD26P

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
📦 PDIP-8 (P)
Same 8-pin PDIP footprint and enable-pin control; this variant adds a lower-power or drive-strength difference versus SN65HVD21P while keeping the same bus pinout

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

MAX485EPA+

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 PDIP-8 (P)
RS-485/RS-422 transceiver · 1 driver · 1 receiver · Half-duplex · 4.75 V to 5.25 V · 2.5 Mbps · Not limited · Short-circuit current limited and protected

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SP485EEN-L

✅ جێگرەوەی ڕاستەوخۆ
MaxLinear
📦 PDIP-8 (P)
Half-duplex RS-422/RS-485 transceiver · 1 transmitter and 1 receiver · 10,000 kbps · Up to 5 Mbps · 4.75 V to 5.25 V · -40 C to +85 C · 8-pin SOIC · Surface mount

پەیوەندی بۆ نرخ

بینینی داتاشیت →

ADM485JNZ

✅ جێگرەوەی ڕاستەوخۆ
Analog Devices
📦 PDIP-8 (P)
1 transmitter and 1 receiver · EIA RS-485 and EIA RS-422 · 4.75 V to 5.25 V · 5 Mbps · +12 V · Differential driver and differential receiver · Logic-controlled input · Logic-controlled input

پەیوەندی بۆ نرخ

بینینی داتاشیت →

SN65HVD21P تایبەتمەندییەکان

Device Type Extended common-mode RS-485 transceiver
Transceiver Configuration 1/1 (one driver, one receiver), half duplex
Supported Standards RS-485, RS-422
Number of Transmitters 1
Number of Receivers 1
پاکێج PDIP (P), 8 pins
ژمارەی پین 8
جۆری دامەزراندن Through-hole
Enable Pins Driver enable (DE), receiver enable (RE)
Termination External, not integrated
Manufacturer Texas Instruments

ڕێکخستنی پینی SN65HVD21P

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
پین 1 RO — Receiver output, logic-level data to the host controller
پین 2 RE — Receiver enable, active-low input
پین 3 DE — Driver enable, active-high input
پین 4 DI — Driver data input from the host controller
پین 5 GND — Ground connection for the transceiver
پین 6 Y — Driver inverting output for the differential pair
پین 7 A — Driver non-inverting output for the differential pair
پین 8 VCC — Positive supply connection for the transceiver

بەکارهێنانە باوەکان

SN65HVD21P گونجاوە بۆ 6 بەکارھێنانs: Industrial Multidrop Sensor Bus, Building Automation and HVAC Controller Networks, Industrial Motor Drive and Encoder Feedback, Utility and Energy Metering Terminals, Long-Distance Instrumentation to Remote Sensors, Legacy Through-Hole Test and Measurement Equipment.

🏭

Industrial Multidrop Sensor Bus

The SN65HVD21P fits factory sensor and actuator buses where several nodes share one twisted pair and ground potentials may drift. Its extended common-mode RS-485 rating keeps the receiver usable when a remote sensor returns data from a ground reference shifted by several volts relative to the controller, a condition that saturates standard RS-485 receivers. The 8-pin PDIP package mounts directly on legacy industrial control boards, and the driver-enable and receiver-enable pins let the host microcontroller arbitrate bus direction for half-duplex polling of up to multiple unit-load nodes.

🏠

Building Automation and HVAC Controller Networks

Building control panels, room thermostats and HVAC controllers typically run RS-485 over long corridors and across floors. The SN65HVD21P is well suited to this environment because its extended common-mode tolerance absorbs the ground differences that appear when controllers are powered from different building circuits, and because the PDIP package fits the through-hole control boards used in this industry. A single transceiver per controller handles both directions of the half-duplex link, with the enable pins driven by the host microcontroller to switch between transmit and receive without external switching components.

⚙️

Industrial Motor Drive and Encoder Feedback

Servo and inverter platforms often carry incremental encoder or drive-status information over RS-485 to a motion controller several metres away. The SN65HVD21P suits this path because the differential receiver rejects the electrical noise generated by switching power stages, and the extended common-mode range covers the offset between the drive ground and the controller ground on multi-axis machines. The half-duplex driver stays disabled except during the encoder response window, which keeps the bus free for other axes sharing the same twisted pair.

🔌

Utility and Energy Metering Terminals

Electric, water and heat metering networks use RS-485 runs between a concentrator and remote meter registers, often outdoors or in shared utility rooms where ground offsets are significant. The SN65HVD21P provides the extended common-mode tolerance needed for these links while keeping the design simple, because one 8-pin PDIP device replaces separate driver and receiver packages and removes the need for an isolation barrier in short-run metering cabinets. The transceiver drives the differential pair directly, and the microcontroller on the meter handles frame timing, CRC and address polling.

📟

Long-Distance Instrumentation to Remote Sensors

Remote pressure, temperature and flow transducers are often connected to a central data logger over cable runs of tens of metres or more. The SN65HVD21P is a good fit for this instrumentation because its extended common-mode range keeps the receiver operating across the ground shift introduced by long cable loops, and because the through-hole PDIP package is common on logger and signal-conditioning boards. Termination resistors at both cable ends and a fail-safe bias network on the logger keep the idle bus state defined, so the receiver output never floats when the sensor is silent.

🖥️

Legacy Through-Hole Test and Measurement Equipment

Bench instruments, programmable power supplies and laboratory data acquisition units built in the through-hole era commonly use an 8-pin PDIP RS-485 socket for instrument control. The SN65HVD21P fits those instruments directly, avoiding a board respin when a faster or more tolerant interface is required, and it lets modern USB-to-RS-485 adapters talk to legacy instruments over long bench cables. Because the device is a single half-duplex transceiver with separate enable pins, the instrument firmware controls direction exactly as it would with a discrete driver and receiver pair.

What is the SN65HVD21P used for?
The SN65HVD21P is a single-driver, single-receiver RS-485 and RS-422 transceiver used to connect a logic-level UART or microcontroller port to a balanced differential bus. Texas Instruments describes it as an extended common-mode RS-485 transceiver, which means its receiver tolerates larger ground-potential differences between connected nodes than a standard RS-485 part. It is typically used in half-duplex point-to-point links and in multidrop buses where several units tap onto one twisted pair.
Where can I download the SN65HVD21P datasheet PDF?
The SN65HVD21P datasheet PDF is available from the Texas Instruments product page for the SN65HVD21 family, with the device-specific ordering information on the SN65HVD21P part-details page, where the part is listed as an extended common-mode RS-485 transceiver in a PDIP (P) package with 8 pins. The manufacturer datasheet contains the pin configuration, the recommended application circuit, the electrical characteristics table and the typical performance curves.
Where can I find the SN65HVD21P pinout and package dimensions?
The SN65HVD21P pin assignment and mechanical drawing are in the pin configuration section of the Texas Instruments SN65HVD21 datasheet, and the same information is mirrored on distributor pinout pages. The device is an 8-pin PDIP (P) through-hole package: pin 1 is the receiver output, pins 2 and 3 are the receiver-enable and driver-enable inputs, pin 4 is the driver data input, pin 5 is ground, pins 6 and 7 are the driver differential outputs, and pin 8 is the supply. Use the package drawing in the datasheet for exact lead pitch and outline.
What is the extended common-mode capability of the SN65HVD21P?
The SN65HVD21P is marketed by Texas Instruments as an extended common-mode RS-485 transceiver, and that extended range is the defining electrical feature of the device. Extended common-mode operation matters when two nodes on the same bus sit at different ground potentials, a common condition in industrial installations with long cable runs and separate power feeds. The exact common-mode voltage limits, together with the supply voltage range and the receiver sensitivity, are specified in the Electrical Characteristics table of the manufacturer datasheet.
What is the difference between RS-422 and RS-485 operation for the SN65HVD21P?
The SN65HVD21P supports both RS-422 and RS-485 signalling because it contains a differential driver and a differential receiver with a common-mode range extended beyond the classic RS-422 limits. In RS-422 the bus is point-to-point with one driver and one receiver, and the receiver is commonly left permanently enabled. In RS-485 the same device can be placed in multidrop mode, so the receiver enable and driver enable pins are used to control bus direction and to hold the driver in a high-impedance state when the node is not transmitting.
SN65HVD21P vs SN65HVD3082EP - which one should I choose?
Choose the SN65HVD21P when you need a through-hole 8-pin PDIP footprint and the extended common-mode behaviour of the HVD21 family; choose the SN65HVD3082EP when you need an 8-pin SOIC surface-mount package for automated assembly. Both parts are single-driver, single-receiver RS-485 transceivers from the same manufacturer, so the functional role in the bus is identical. The deciding factor is mechanical: the PDIP version fits legacy through-hole industrial boards and hand-assembled prototypes, while the SOIC version suits high-density surface-mount designs.
What is the difference between the SN65HVD21P and the SN65HVD22P?
Both are 8-pin PDIP single-driver, single-receiver RS-485 transceivers from Texas Instruments, so they share the same bus role and the same through-hole footprint. The SN65HVD21P is the extended common-mode member of the family and is the safer choice when ground-potential differences between nodes are large or when the cable run is long and unshielded. The SN65HVD22P is the sensible alternative when the installation is short, well-shielded and well-grounded and a lower-power or lower-cost option is preferred. Verify the exact electrical ratings for both against your bus conditions in the manufacturer datasheets.
When should I choose the SN65HVD21P over the MAX485EPA?
Choose the SN65HVD21P when the bus must survive large ground offsets between nodes, long unshielded cables, or industrial environments with electrically noisy neighbours, because it is specified for extended common-mode operation. Choose the MAX485EPA when the bus is short, tightly controlled and cost-driven, and when a standard common-mode range is sufficient. Both are 8-pin PDIP single-transceiver parts with a similar enable-pin architecture, so the swap is usually mechanical. The trade-off is that the SN65HVD21P is the better-specified choice for field-installed industrial cabling.
Is the SN65HVD21P suitable for an industrial multidrop RS-485 bus?
The SN65HVD21P suits industrial multidrop RS-485 buses because it is an extended common-mode transceiver in an 8-pin PDIP package, and the extended range addresses exactly the ground-potential offsets that appear when sensors and controllers on a long factory cable run are powered from different supplies. For a multidrop bus, keep the driver disabled on all but the transmitting node, apply termination only at the two physical ends of the run, and bias the idle state so the receiver output stays defined when no node is transmitting.
What is the best drop-in replacement for the SN65HVD21P?
The closest drop-in replacements for the SN65HVD21P are the other 8-pin PDIP single-transceiver RS-485 parts with the same driver-enable, receiver-enable and data-in arrangement: the SN65HVD22P from Texas Instruments, and the MAX485EPA and SP485EEN from Maxim and SGMicro respectively. They fit the same through-hole footprint and require the same wiring, but their common-mode and supply ratings differ, so confirm the electrical characteristics in each manufacturer datasheet before substituting into a field-installed bus.
Can the SP485EEN replace the SN65HVD21P?
The SP485EEN can be used as a drop-in replacement for the SN65HVD21P in most designs because both are 8-pin PDIP RS-485 transceivers with the same single-driver, single-receiver arrangement and the same enable-pin wiring. The practical difference is electrical tolerance: the SN65HVD21P is specified for extended common-mode operation, which suits long or noisy industrial runs, whereas the SP485EEN is better matched to shorter, well-controlled links. Confirm the supply range, common-mode limits and receiver threshold in the SGMicro datasheet before committing.
What can replace the SN65HVD21P?
Replacements for the SN65HVD21P include the SN65HVD22P from Texas Instruments for a same-family alternative, plus the MAX485EPA from Maxim, the SP485EEN and the ADM485JN from SGMicro and Analog Devices, all of which are 8-pin PDIP single-driver, single-receiver RS-485 transceivers with matching enable-pin logic. Treat the SN65HVD21P as the preferred choice where extended common-mode tolerance is needed, and confirm the electrical characteristics and supply range of any substitute in its own manufacturer datasheet.
Is the SN65HVD21P the same as the MAX485EPA?
No, the SN65HVD21P and the MAX485EPA are not the same part. The SN65HVD21P is a Texas Instruments extended common-mode RS-485 transceiver in an 8-pin PDIP package, while the MAX485EPA is a Maxim single-driver, single-receiver RS-485 transceiver in an 8-pin PDIP package with a standard common-mode range. They are pin-compatible for most through-hole designs, but the SN65HVD21P is the better match for long or noisy industrial cabling.
Where can I buy the SN65HVD21P online?
The SN65HVD21P can be ordered through the Request a Quote form on this page, which is the fastest route to current availability, a firm lead time and a quotation for the 8-pin PDIP package. Texas Instruments lists the part under the SN65HVD21 family ordering information, and the device is also carried by major authorized distributors. Submit the quantity, target date and delivery location with your quote request for a confirmed shipment schedule.
What is the lead time for the SN65HVD21P?
Lead time for the SN65HVD21P depends on factory loading and the quantity ordered, so it should be confirmed at the time of quotation rather than assumed. Use the Request a Quote form on this page and state the required quantity, the target delivery date and whether you need the standard PDIP (P) package, and the manufacturer or an authorized distributor will return a committed schedule. For prototype quantities expect a shorter window than for production volumes scheduled into an assembled board build.
Is the SN65HVD21P in stock and what does it cost?
Stock levels and pricing for the SN65HVD21P change with factory load and order volume, so use the Request a Quote form on this page for the current availability, unit price and confirmed schedule. The quote request covers the 8-pin PDIP (P) package and can be submitted for prototype quantities as well as production volumes. The manufacturer lists the SN65HVD21 as an active family member, so new orders can be placed against the standard ordering information.
What are the key specifications of the SN65HVD21P that engineers should know?
The SN65HVD21P is a Texas Instruments extended common-mode RS-485 and RS-422 transceiver with one driver and one receiver, supplied in an 8-pin PDIP (P) through-hole package. Key engineering facts are the half-duplex architecture, the shared driver-enable and receiver-enable control scheme for bus turnaround, the extended common-mode rating, and the requirement for external termination and biasing resistors on long runs. Supply voltage range, maximum data rate, receiver threshold and common-mode limits are given in the Electrical Characteristics table of the manufacturer datasheet.
What is the best Maxim equivalent for the SN65HVD21P?
The MAX485EPA is the closest Maxim equivalent for the SN65HVD21P, because it is a single-driver, single-receiver RS-485 transceiver in an 8-pin PDIP package with equivalent enable-pin control and the same host-side UART interface. The functional difference is the common-mode tolerance: the SN65HVD21P is specified for extended common-mode operation and is preferable on long or noisy industrial runs, while the MAX485EPA is typically chosen for short, cost-driven links. Verify the electrical ratings and supply range in the Maxim datasheet before substituting.

داتای سەرچاوەی ئەندازیاری بۆ SN65HVD21P — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the SN65HVD21P when your RS-485 bus runs on long, unshielded or poorly grounded industrial wiring, or when ground potential differences between nodes are likely, because its extended common-mode specification is the reason this part exists in the family. It is also the right choice for legacy through-hole boards that cannot accept a surface-mount footprint. Choose the SN65HVD22P or SN65HVD23P when you prefer staying inside the same Texas Instruments family and the bus conditions are tame enough for standard common-mode operation. Choose the MAX485EPA or SP485EEN for short, cost-driven links where standard common-mode tolerance is sufficient, and choose an isolated transceiver such as an ISO1042-type device when ground isolation, not common-mode range, is the dominant requirement. Always confirm the supply range, receiver threshold and common-mode limits of the chosen part in its own datasheet before signing off the design.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە SN65HVD22P SN65HVD23P SN65HVD26P MAX485EPA SP485EEN ADM485JN
Package PDIP-8 (P), through-hole PDIP-8 (P) - same PDIP-8 (P) - same PDIP-8 (P) - same PDIP-8 (P) - same PDIP-8 (P) - same PDIP-8 (P) - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Maxim Integrated SGMicro Analog Devices
Transceiver Configuration 1/1, half duplex 1/1, half duplex 1/1, half duplex 1/1, half duplex 1/1, half duplex 1/1, half duplex 1/1, half duplex
Supported Standards RS-485, RS-422 RS-485, RS-422 RS-485, RS-422 RS-485, RS-422 RS-485, RS-422 RS-485 RS-485, RS-422
Enable Pin Control Separate DE and RE inputs Separate DE and RE inputs Separate DE and RE inputs Separate DE and RE inputs Separate DE and RE inputs Separate DE and RE inputs Separate DE and RE inputs
Termination External External External External External External External

جیاکەرەوە سەرەکییەکان

  • Extended common-mode rating for noisy, ground-shifted industrial buses (بەراورد بەMAX485EPA)
  • Through-hole 8-pin PDIP package keeps legacy boards buildable (بەراورد بەSN65HVD3082EP)
  • Single package provides both driver and receiver with separate enable pins (بەراورد بەADM485JN)

تێبینییەکانی دیزاین

Route the differential pair A and Y as a tightly coupled pair on a continuous ground plane, keep the driver output traces short and away from switching nodes, and connect the transceiver ground pin directly to the board ground plane with a short, low-inductance via. In a through-hole PDIP design keep the layout compact: the 8-pin package makes it easy to place the transceiver near the connector, and every extra centimetre of unpaired stub degrades the differential signal at higher data rates.

Decouple the supply pin with a local 0.1 uF ceramic capacitor placed as close to pin 8 as the layout allows, and add a bulk bulk electrolytic or larger ceramic close to the transceiver if the cable run is long. Because a half-duplex driver delivers a large current step when it switches the bus, inadequate local decoupling shows up as bus errors that look like noise problems rather than supply problems. Tie the transceiver ground to the board ground at a single point rather than routing it through the cable shield.

Two mistakes dominate RS-485 designs. First, terminating the bus at every node instead of only at the two physical ends over-damps the signal and reduces the differential swing at the far end. Second, leaving the bus without a fail-safe bias network lets the receiver output float when all drivers are disabled, which the host reads as random data. Apply termination only at the end nodes, add a bias network at one location, and confirm the enable logic so the driver is high-impedance except during transmit windows.

Half-duplex turnaround timing is the other frequent failure source. The host controller must wait for the driver to release the bus before the receiver output is valid, and the enable pins must never be driven in a way that overlaps two nodes transmitting. Use the receiver-enable and driver-enable inputs from the same GPIO or from a direction-controlled signal so there is no dead time ambiguity, and validate the worst-case delay at the maximum supported bus data rate before freezing the firmware timing.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No explicit RoHS, REACH, lead-free or conflict-minerals statement appears in the manufacturer or distributor listings for this part. The device is an industrial interface IC and is not offered in an AEC-Q100 automotive-qualified variant in the listings reviewed.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

SN65HVD21P SN65HVD21P datasheet SN65HVD21P datasheet pdf SN65HVD21P pinout SN65HVD21P RS-485 transceiver Texas Instruments SN65HVD21P SN65HVD21P vs SN65HVD3082EP SN65HVD21P vs MAX485EPA SN65HVD21P drop-in replacement SN65HVD21P equivalent 8-PDIP SN65HVD21P common mode range SN65HVD21P RS-485 application circuit SN65HVD21P buy

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments SN65HVD21 SN65HVD21P SN65HVD22P SN65HVD3082EP MAX485EPA SP485EEN ADM485JN RS-485 RS-422 RS-485 transceiver differential line driver differential receiver half-duplex interface IC interface IC integrated circuit semiconductor common-mode voltage extended common-mode range fail-safe bias termination resistor PDIP-8 through-hole package multidrop bus industrial automation building automation
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ