SN75116D - 5V Differential Line Transceiver | Texas Instruments
MPN: SN75116D ✓ چالاکSN75116D گشتی
A differential line transceiver is an interface IC that converts between single-ended digital logic signals and differential signals carried by a balanced line. This signal conversion helps equipment communicate more reliably over cables or buses while remaining compatible with TTL-based systems. The SN75116D belongs to the interface IC hierarchy, where transceivers connect digital logic to physical communication lines.
The principal features include a 4.5 V to 5.5 V operating supply range, TTL-compatible driver inputs, TTL-compatible receiver outputs, 3-state driver output circuitry, and differential line operation. Its single transceiver arrangement integrates one driver channel and one receiver channel in each 16-pin SOIC package, making it appropriate for compact point-to-point, bus-organized, and party-line interfaces.
The SN75116D is designed for party-line and data-bus applications where multiple nodes may share a communication line. The 3-state driver output allows the driver to be disconnected electrically when it is not active, supporting shared-bus architectures. TTL-compatible logic levels simplify interfacing with conventional digital systems, while differential line operation improves signal integrity across the physical transmission path.
Typical uses include industrial data acquisition, instrumentation, test equipment, embedded control links, and industrial communication networks. The device is particularly relevant when a system requires bidirectional differential signaling but only one driver and one receiver channel. Its SOIC package also supports conventional surface-mount assembly rather than requiring a through-hole connection.
Designers should use the manufacturer datasheet pin-description table when assigning signals and should account for the 4.5 V to 5.5 V supply requirement. The 3-state output must be controlled correctly on a shared bus, and the external line network should be configured to prevent multiple drivers from actively driving the same node at the same time.
This page organizes the SN75116D technical characteristics, sourcing information, verified drop-in alternative, interface applications, comparison parameters, and practical PCB design guidance. It helps engineers evaluate the transceiver against same-footprint replacements while keeping electrical compatibility and bus topology central to the selection.
جێگرەوەکانی جێگۆڕکێ بۆ SN75116D — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN75116D (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Mounting Type, Operating Temperature Range, Package, Product Type.
SN75116N
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →SN75116D تایبەتمەندییەکان
| Product Type | 1/1 Differential Line Transceiver |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Driver Configuration | 1 differential driver with 3-state output |
| Receiver Configuration | 1 differential receiver |
| Driver Input Compatibility | TTL-compatible |
| Receiver Output Compatibility | TTL-compatible |
| Line Signal Type | Differential |
| Supported Network Topology | Party-line and data-bus |
| پاکێج | 16-pin SOIC (D) |
| Package Pin Count | 16 pins |
| جۆری دامەزراندن | Surface Mount |
| مەودای پلەی گەرمیی کارکردن | 0 C to 70 C |
| دۆخی RoHS | Compliant |
ڕێنمایی ڕێکخستنی پینی SN75116D 16 pins
ڕێکخستنی پین بۆ SN75116D (پاکێجی 16 pins). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ SN75116D.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
SN75116D گونجاوە بۆ 6 بەکارھێنانs: Industrial Data Acquisition, Party-Line Communication Bus, Test and Measurement Equipment, Embedded Control Communication Link, Point-to-Point Differential Link, Laboratory Instrument Interface.
Industrial Data Acquisition
The SN75116D fits industrial data-acquisition systems that connect TTL-based control logic to a balanced measurement or communication line. Its 4.5 V to 5.5 V operating range matches a conventional 5 V equipment rail, while the differential driver and receiver support communication over a physically longer or noisier path than a direct single-ended interface. The 3-state driver output is particularly useful when several distributed modules share one bus. Designers should place the transceiver near the line connector, follow the manufacturer reference connection, and use the datasheet pin descriptions when arranging receiver strobe and driver-enable control signals.
Party-Line Communication Bus
Party-line networks place multiple nodes on the same communication path, making the SN75116D's 3-state differential driver output a central feature for bus contention control. The device operates from a single 4.5 V to 5.5 V supply and presents TTL-compatible driver inputs and receiver outputs to the surrounding digital logic. In a practical implementation, each node must disable its driver whenever another node is transmitting. Cable length, termination, grounding, and allowable loading should be calculated from the manufacturer's application guidance rather than inferred from the 5 V supply specification.
Test and Measurement Equipment
The SN75116D can bridge a TTL-based instrument controller and a differential test interface in equipment where cable noise, grounding differences, or longer interconnect runs make single-ended communication less dependable. Its one-driver, one-receiver arrangement provides bidirectional physical-layer signaling while retaining a familiar 16-pin SOIC interface at the logic side. The differential line circuitry handles the physical signaling, but system timing still depends on the driver's data rate and receiver delay specified in the manufacturer datasheet. PCB placement should keep the line-side return path short and matched to the external cable or fixture.
Embedded Control Communication Link
The SN75116D is suitable for embedded controllers that need a differential communications interface alongside TTL logic. Its 4.5 V to 5.5 V supply range can be derived from the same 5 V rail used by common control hardware, reducing the number of incompatible interface voltages in the assembly. The TTL-compatible driver inputs allow the controller to control the transmission state, while the 3-state output allows bus sharing. Firmware and hardware must coordinate node addressing so that only one driver asserts the line at a time, and the receiver output must be sampled within the timing limits specified for the device.
Point-to-Point Differential Link
A point-to-point installation can use the SN75116D to transmit and receive one differential signal over a dedicated cable between two circuit assemblies. The 4.5 V to 5.5 V operating range supports conventional 5 V logic systems, and TTL-compatible inputs and outputs reduce the interface complexity between the transceiver and digital circuitry. Differential signaling is useful when the connection crosses a larger physical distance or enters an environment with potential coupling between conductors. The external cable still requires suitable characteristic impedance and termination, while the PCB must maintain a closely coupled differential trace pair from the SOIC pins to the connector.
Laboratory Instrument Interface
Laboratory instruments often combine TTL control logic with external differential communication ports. The SN75116D provides one differential driver and one differential receiver in a 16-pin SOIC package, allowing both transmit and receive functions to share the same physical interface circuit. Its single 5 V-class supply operates from 4.5 V to 5.5 V, and its receiver output is compatible with TTL logic. The transceiver does not by itself define the command protocol or connector standard, so the system designer must add the correct line termination and ensure that the external test environment observes the electrical limits in the manufacturer datasheet.
داتای سەرچاوەی ئەندازیاری بۆ SN75116D — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | SN75116N |
|---|---|---|
| Package | 16-pin SOIC (D) | 16-pin SOIC |
| Brand | Texas Instruments | Texas Instruments |
| Product Type | 1/1 Differential Line Transceiver | Differential Line Transceiver |
| Network Topology | Party-line and data-bus | Party-line and data-bus |
| Mounting Type | Surface Mount | Surface Mount |
جیاکەرەوە سەرەکییەکان
- Directly identified same-footprint replacement path (بەراورد بەSN75116N)
- Single 5 V-class interface for conventional logic systems (بەراورد بەSN75116N)
- Integrated bidirectional physical-layer function (بەراورد بەSN75116N)
تێبینییەکانی دیزاین
Place the SN75116D close to the cable or board connector so the differential traces remain short. Route the two line conductors as a closely coupled pair on the same board layer, minimize stubs and test pads, and provide a continuous ground reference beneath the pair. Keep the digital-side driver and receiver traces away from the line-side nodes to reduce coupling between the 5 V logic circuitry and the differential communication path.
Use the manufacturer pin-description table to separate enable, strobe, data, and supply connections before assigning the 16 SOIC pins. In particular, do not borrow the enable architecture of the related SN75118 or SN75119 because the SN75116 family uses receiver-output strobe functionality. Place the decoupling capacitor directly across the device supply pins and route it with a short ground return to minimize supply-loop area.
Ensure that only one node actively drives a shared party-line bus at any time. The 3-state output must enter a high-impedance state before another node transmits, and control timing should include the device's specified enable and propagation intervals. Also avoid treating the SN75176 or SN75174 as direct substitutions merely because they are also line-interface ICs; their package sizes, control functions, and pin arrangements must be checked separately.
زانیاری پابەندبوون
The component listing identifies SN75116D as RoHS compliant. No additional REACH, halogen-free, conflict-minerals, or automotive qualification claims are stated.