Texas Instruments

SN75188D - Quadruple RS-232 Line Driver | Texas Instruments

MPN: SN75188D ✓ چالاک
7.5 V to 15 V Vdss 10 mA typical Id 14-pin SOIC Package
MOQ: 1 |

SN75188D گشتی

Texas Instruments SN75188D is a monolithic quadruple RS-232 line driver with four driver channels, a 7.5 V to 15 V supply range, and a 14-pin SOIC package. Designed for data-terminal-equipment and data-communications-equipment interfaces, the device conforms to ANSI TIA/EIA-232-E and is designed to interchange with the Motorola MC1488. Each channel uses current limiting, with typical current limiting set at 10 mA.

An RS-232 line driver is a differential-interface transmitter that converts TTL or CMOS logic levels into the bipolar voltage swings required by RS-232 links. The SN75188D belongs to the line-driver, interface-IC, and power-management-adjacent signal-interface hierarchy, but its primary function is signal conditioning rather than voltage regulation. It is intended for systems that transmit serial data over longer distances than logic-level interconnects reliably support.

The principal features include four independent driver outputs, typical 10 mA output current limiting, power-off output impedance of at least 300 ohms, and slew-rate control through the load capacitor. Current limiting protects the interface when a driver output encounters a fault or improperly terminated cable. The power-off output impedance helps prevent an inactive transmitter from disturbing a connected bus.

Each channel requires an external diode in series with its supply-voltage terminal when used in the conventional configuration described by TI. Output transition behavior depends on the capacitive load, so external load capacitance and cable length directly affect signal integrity. The design is based on a monolithic bipolar line-driver architecture rather than a multi-chip discrete implementation.

Typical applications include legacy RS-232 ports on industrial controllers, data-logging equipment, test systems, computer peripherals, and instrumentation. The device can also drive four channels toward compatible RS-232 receivers, while modern system designs frequently pair a line driver with a quad line receiver to create complete two-way RS-232 interfaces.

For a new layout, place the 14-pin SOIC close to the connector and route each driver trace away from sensitive analog circuitry. Confirm driver polarity, connector pin assignment, external supply-diode orientation, and maximum capacitive loading before releasing the PCB. Use the TI pin-description table when assigning tracks because the exposed logic side and RS-232 output side must not be interchanged.

This product page consolidates device specifications, verified source links, replacement context, interface comparisons, and practical RS-232 layout guidance. It helps engineers distinguish the SN75188D from line receivers, full transceivers, and electrically similar but footprint-incompatible alternatives.

جێگرەوەکانی جێگۆڕکێ بۆ SN75188D — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN75188D (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Interface Standard, Output Current Limiting.

onsemi
Interface Standard: EIA-232D
Output Current Limiting: Integrated current-limited outputs
بەراوردکردن لەگەڵ SN75188D →

SN75C188DR

✅ جێگرەوەی ڕاستەوخۆ
📦 14-SOIC
The SN75C188DR is identified as a low-power quadruple line driver; its power and switching characteristics differ by up to 30% from the SN75188D, while the 14-SOIC package and driver architecture are retained.

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

SN75188D تایبەتمەندییەکان

Device Type Quadruple RS-232 line driver
Number of Driver Channels 4
Logic Direction 4/0 driver
Supply Voltage Range 7.5 V to 15 V
Output Current Limiting 10 mA typical
Power-Off Output Impedance 300 ohms minimum
Interface Standard ANSI TIA/EIA-232-E
ITU Recommendation V.28
Slew-Rate Control Controlled by load capacitor
Supply Protection Diode in series with each supply-voltage terminal in the typical application
Interchangeability Designed to be interchangeable with the Motorola MC1488
مەودای پلەی گەرمیی کارکردن 0 °C to 70 °C
پاکێج 14-pin SOIC
جۆری دامەزراندن Surface mount

ڕێنمایی ڕێکخستنی پینی SN75188D 14-pin soic

ڕێکخستنی پین بۆ SN75188D (پاکێجی 14-pin soic). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 14-pin soic بۆ SN75188D

هیچ داتای وردی پینئاوت بەردەست نییە بۆ SN75188D.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

SN75188D گونجاوە بۆ 6 بەکارھێنانs: Legacy RS-232 Data Ports, Industrial Controller Serial Interfaces, Data Logging and Test Equipment, Computer Peripherals and Printers, Communication Port Concentrators, Instrumentation and External Control.

🖥️

Legacy RS-232 Data Ports

The SN75188D is well suited to legacy RS-232 ports that need four unidirectional channels from one device. Its four independently controlled drivers convert TTL or CMOS logic into bipolar RS-232 levels for equipment-to-equipment communication. The typical 10 mA current limit helps contain output faults, while the 7.5 V to 15 V supply range fits conventional interface rails. Designers should follow the TI external supply-diode configuration, keep driver traces away from sensitive circuitry, and verify connector polarity before fabrication.

🏭

Industrial Controller Serial Interfaces

An industrial controller can use the SN75188D to provide four protected RS-232 driver channels for configuration ports, service interfaces, or legacy peripherals. The device's ANSI TIA/EIA-232-E and ITU V.28 interface focus supports compatibility with established RS-232 equipment. The 0 °C to 70 °C SN75188 rating covers many indoor controller environments, but it does not cover harsher extremes. Use the current-limited outputs, install the manufacturer-recommended supply diodes, and validate cable capacitance against the selected data rate.

📟

Data Logging and Test Equipment

The SN75188D can provide four RS-232 transmit channels in data loggers, test instruments, and laboratory interfaces that must communicate with older computer equipment. Its monolithic quadruple implementation reduces the number of separate driver packages and standardizes channel behavior. Typical 10 mA output current limiting helps manage accidental output faults, while the 300-ohm minimum power-off output impedance reduces unwanted effects from inactive channels. Confirm signal polarity, connector mapping, and allowable capacitive loading for each instrument.

🖨️

Computer Peripherals and Printers

Older printers, scanners, and computer peripherals can be supported with the SN75188D when the host interface requires four RS-232 driver outputs. The SN75188D provides the bipolar voltage conversion required between logic-level commands and an RS-232 cable while adding typical output current limiting. Its 14-pin SOIC package supports conventional surface-mount assembly. Verify DTE versus DCE signaling, pin assignments, and cable direction because a driver-only device cannot receive return data without separate receiver circuitry.

🌐

Communication Port Concentrators

A communication concentrator can use the SN75188D to fan out logic-controlled data toward multiple RS-232-equipped devices when the required channels are transmit-only. Four driver channels in one 14-pin SOIC package can simplify board partitioning and channel management. The current-limited outputs improve robustness, while power-off output impedance provides a defined inactive state. The designer must still ensure that only the intended channel is enabled, maintain compatible logic levels, and account for load capacitance and cable length at the intended signaling rate.

🔧

Instrumentation and External Control

The SN75188D fits instrumentation that sends commands or test stimuli to external equipment through an RS-232 connection. Four channels can control multiple devices or separate command functions while sharing a common interface supply. Its monolithic implementation provides consistent channel characteristics, and the typical 10 mA output limit helps withstand connector or wiring faults. Place the device near the connector, use short driver traces, follow the required supply-diode arrangement, and verify that instrumentation ground and signal-ground practices are compatible with the target port.

What is the SN75188D and what does it do?
The SN75188D is a Texas Instruments monolithic quadruple RS-232 line driver with four current-limited outputs. According to the TI SN75188 datasheet Rev. C, it converts TTL or CMOS logic signals into bipolar RS-232 levels for connections between data-terminal equipment and data-communications equipment. Each channel is independently controlled, and the device supports ANSI TIA/EIA-232-E and ITU V.28 interfaces.
What is the supply voltage range of the SN75188D?
The SN75188D operates from 7.5 V to 15 V. The TI SN75188 datasheet Rev. C identifies this range for the SN75188 family, which also contains the MC1488 and SN55188 variants. The supply pins require the external series-diode arrangement shown in the manufacturer's typical application circuit when used with the conventional power connection.
What package does the SN75188D use?
The SN75188D is packaged in a 14-pin SOIC. TI identifies the device as a surface-mount quadruple line driver, while the distributor product listing describes the SN75188D as a 14-SOIC RS-232 4/0 driver. Use the TI pin-description table when making PCB assignments because the logic inputs, RS-232 outputs, supply terminals, and ground pins have different circuit roles.
Where can I download the SN75188D datasheet PDF?
The official SN75188D datasheet is available through TI at https://www.ti.com/lit/gpn/SN75188. TI's product page for SN75188 also provides ordering information and supporting documentation. The datasheet is identified as Rev. C and covers the MC1488, SN55188, and SN75188 family, including the external supply-diode arrangement, typical interface application, and electrical characteristics.
Where can I find the SN75188D pinout?
The SN75188D pin assignments are shown in the TI SN75188 datasheet Rev. C, whose ordering and pin-configuration information is linked from the official SN75188 product page. The package has 14 pins divided between four driver inputs, four driver outputs, supply connections, and ground. Consult that manufacturer table when routing the PCB because an incorrect logic-to-RS-232 connection can damage an attached interface.
What is the output current limit of the SN75188D?
Each SN75188D output has a typical current limit of 10 mA. The TI SN75188 datasheet Rev. C identifies current-limited outputs as a key feature, helping contain fault current when a cable or load imposes an abnormal condition. The limit is a typical figure rather than a guaranteed maximum, so designers should also observe the complete absolute-maximum ratings and operating conditions in the datasheet.
Does the SN75188D meet RS-232 standards?
Yes, the SN75188D is designed to meet ANSI TIA/EIA-232-E and ITU Recommendation V.28. TI's SN75188 datasheet Rev. C describes the MC1488, SN55188, and SN75188 as monolithic quadruple line drivers for data-terminal-equipment and data-communications-equipment interfaces. Compliance of the complete link still depends on correct implementation, including signal levels, loading, cable construction, and connector wiring.
What is the difference between SN75188D and MC1488?
The SN75188D and MC1488 implement the same general function as quadruple RS-232 line drivers, and TI states that the SN75188 is designed to interchange with the Motorola MC1488. Their orderable packages, qualification details, and ordering information can differ, so the device suffix must be checked before substitution. The SN75188D specifically uses a 14-pin SOIC package and is characterized for 0 °C to 70 °C operation.
Is SN75188D the same as SN75C188DR?
The SN75188D and SN75C188DR are related quadruple line-driver solutions, but they should not be treated as automatically identical without checking the pin table and electrical limits. Cross-reference listings identify both as 14-SOIC devices, while the SN75C188DR is described as a low-power quadruple line driver. Confirm output polarity, supply arrangement, speed, load capability, and temperature grade before using it as a drop-in replacement.
When should I choose the SN75188D instead of another RS-232 driver?
Choose the SN75188D when a design needs four conventional RS-232 driver channels, a 7.5 V to 15 V supply, and current-limited outputs with typical 10 mA limiting. It is appropriate for legacy RS-232 ports where four unidirectional channels are needed from one package. Select a full transceiver instead when the design requires integrated receiver channels, or a modern interface IC when lower-voltage operation and smaller footprints are priorities.
Is the SN75188D suitable for an industrial RS-232 port?
The SN75188D can suit an industrial RS-232 port when its 0 °C to 70 °C operating range covers the equipment environment and the interface is electrically compatible with the connected equipment. TI also characterizes the SN55188 member of the same family for the military temperature range of -55 °C to 125 °C. For wider-temperature industrial equipment, choose the appropriately qualified device rather than assuming the SN75188D covers the full ambient range.
What is the best drop-in replacement for the SN75188D?
No fully verified five-part drop-in set can be established from the available cross-reference information for the SN75188D. The SN75C188DR is a related 14-SOIC quadruple driver, but its low-power designation means its speed, loading, and implementation details must be compared with the SN75188D before substitution. A replacement is suitable only after its pinout, supply pins, output polarity, current limit, slew behavior, and temperature range are checked.
How do I drive RS-232 with the SN75188D?
Connect each TTL or CMOS control signal to the corresponding driver input and route each driver output to the intended RS-232 connector pin. Follow the TI typical application for the series diode connected to each supply-voltage terminal and confirm the external load capacitance. Because the SN75188D has driver channels only, a separate receiver is required when the interface must also receive data.
Can the SN75188D replace a full RS-232 transceiver?
The SN75188D cannot replace a full RS-232 transceiver unless the existing board provides a separate receiver and the unused receiver functions are unnecessary. The SN75188D contains four driver outputs and no receiver inputs, while a transceiver combines drivers and receivers in one package. A pin-for-pin footprint match is also insufficient because the logic-side functions are fundamentally different.
Where can I buy the SN75188D and check its price and lead time?
Use the Request a Quote form on this page to request current SN75188D pricing, stock, minimum order quantity, and lead time. Quote requests ensure that the package suffix and shipping quantity match the production requirement. The SN75188D is listed as a 14-SOIC device, so confirm that the requested orderable part number is specifically SN75188D rather than a different package or temperature-grade suffix.

داتای سەرچاوەی ئەندازیاری بۆ SN75188D — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the SN75188D when a design requires four dedicated RS-232 driver channels, a 7.5 V to 15 V interface supply, and typical 10 mA output current limiting. It is particularly useful for legacy DTE or DCE equipment, test instruments, data loggers, and industrial controllers operating within the 0 °C to 70 °C range. The device requires the external supply-diode arrangement shown by TI and does not provide receiver channels.

Consider the SN75C188DR when its low-power characteristics better match the design and its exact pin and electrical characteristics have been verified. Although both are identified as 14-SOIC quadruple line drivers, shared channel count and package are not enough to guarantee interchangeability. Compare supply handling, output polarity, current limiting, slew rate, power-off impedance, and temperature rating.

For new dual-direction interfaces, consider a full RS-232 transceiver such as MAX232NSR to reduce the number of interface components. Use an industrial bus transceiver such as SN65HVD37D when the physical link is RS-485 rather than RS-232. The SN75188D is best reserved for established RS-232 transmit-only channels where its conventional driver behavior and fault-current limiting match the target equipment.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە SN75C188DR
Device Type Quadruple RS-232 line driver Quadruple low-power line driver
Brand Texas Instruments Texas Instruments
Package 14-SOIC 14-SOIC - same
Driver Channels 4 4
Logic Direction 4/0 driver 4/0 driver
Low-Power Designation Not designated as low-power in the available description Low-power
RS-232 Interface Support ANSI TIA/EIA-232-E and ITU V.28 RS-232 line-driver application

جیاکەرەوە سەرەکییەکان

  • Four conventional RS-232 transmitter channels (بەراورد بەSN75C188DR)
  • Explicit power-off output impedance (بەراورد بەSN75C188DR)
  • Documented standards alignment (بەراورد بەSN75C188DR)

تێبینییەکانی دیزاین

Place the SN75188D close to the RS-232 connector and route each output directly to its assigned connector pin. Keep switching and logic traces away from the bipolar driver outputs, and provide a clear ground return for the interface. Confirm DTE or DCE signal direction before layout because the SN75188D contains transmitters only; a receive path requires separate receiver circuitry or a transceiver.

Follow the TI SN75188 typical application and place a diode in series with each supply-voltage terminal for the conventional configuration. The external diodes provide supply protection under the documented operating scheme. Verify diode polarity and the resulting supply voltage at the IC, especially when using the upper end of the 7.5 V to 15 V device supply range.

The output slew rate is controlled by the load capacitor, so capacitance from the PCB, connector, cable, and protection network directly affects transition speed and signal integrity. Start with the shortest practical routing and avoid unnecessary test pads or long stubs. Validate the slowest required data rate and worst-case cable condition on hardware rather than assuming that nominal capacitance applies across every connector variant.

Do not substitute a line receiver, full transceiver, or driver with a different package solely because the channel count matches. Check input versus output direction, supply-diode implementation, output polarity, current limiting, power-off impedance, temperature range, and connector pinout. The SN75188D operates over 0 °C to 70 °C; use a wider-temperature family member when the enclosure environment exceeds that range.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The available product information identifies the SN75188D as a commercial-temperature RS-232 line driver but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to this conventional interface IC.

داتا پشتڕاستکراوەتەوە لە: 2026-11-03 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

SN75188D datasheet SN75188D pinout SN75188D datasheet pdf SN75188D equivalent SN75188D replacement SN75188D vs SN75C188DR SN75188D cross reference Texas Instruments SN75188D SN75188D 14-SOIC pinout SN75188D RS-232 application circuit SN75188D price SN75188D stock

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments SN75188D SN75C188DR MC1488 SN55188 quadruple line driver RS-232 line driver RS-232 interface IC transmitter semiconductor ANSI TIA/EIA-232-E ITU Recommendation V.28 TTL logic CMOS logic current limiting power-off output impedance slew-rate control 14-pin SOIC SOIC family surface-mount package DTE DCE legacy serial port industrial controller data terminal equipment data communications equipment operating temperature range supply voltage
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ