SN75188N - 4x RS-232 Line Driver | Texas Instruments
MPN: SN75188N ✓ چالاکSN75188N گشتی
A quadruple line driver converts TTL or CMOS logic-level signals into balanced, bipolar RS-232 signaling levels. The SN75188N is commonly used when a system needs four transmit channels and does not require a matching receiver inside the same package. Its four independent drivers make it suitable for parallel serial ports, industrial control links, test equipment, multi-channel data acquisition, and legacy computer interfaces. The 14-PDIP format also supports conventional through-hole prototyping and maintenance repairs.
Key electrical characteristics include current-limited outputs with approximately 10 mA typical current limiting and a minimum power-off output impedance of 300 ohms. The internal series diodes associated with the supply terminals support bipolar RS-232 operation. Output slew rate is controlled by the load capacitance, allowing transition speed to be matched to the driven cable and receiver network rather than relying on a fixed high-speed edge.
The SN75188N operates across the commercial temperature range of 0°C to 70°C. Its through-hole construction and 14-pin DIP outline make it straightforward to install in legacy control systems, but the package requires more PCB area than a surface-mount alternative. Modern mixed-signal designs may choose a surface-mount transceiver or multi-channel interface IC when PCB area, power consumption, or newer logic levels are more important than legacy compatibility.
For reliable use, verify the output swing and receiver thresholds against the RS-232 load, keep unused driver outputs terminated in the same manner as active channels, and provide the required bypass capacitance close to each supply pin. Confirm that the connected equipment uses compatible signal polarities and connector pin assignments before replacing a discrete driver network with this monolithic quad driver.
This page combines manufacturer device information, RS-232 interface specifications, drop-in cross-reference results, application guidance, and practical implementation notes. It highlights where the SN75188N fits legacy bipolar interfaces, where modern surface-mount transceivers provide a better engineering trade-off, and which compatibility checks matter before substituting the part into an existing circuit.
جێگرەوەکانی جێگۆڕکێ بۆ SN75188N — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ SN75188N (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Mounting Type, Interface Standard, Product Type, Operating Temperature Range.
SN75C188N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MC1488P
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →SN75188N تایبەتمەندییەکان
| Product Type | Quadruple RS-232 Line Driver |
| Number of Drivers | 4 |
| Supply Voltage Range | ±7.5 V to ±15 V |
| مەودای پلەی گەرمیی کارکردن | 0°C to 70°C |
| پاکێج | 14-PDIP, through hole |
| جۆری دامەزراندن | Through-Hole |
| Interface Standard | ANSI TIA/EIA-232-E |
| ITU Recommendation | V.28 |
| Current-Limited Output | 10 mA typical |
| Minimum Power-Off Output Impedance | 300 ohm |
| Output Slew Rate Control | Controlled by load capacitance |
| Supply Protection Structure | Diode in series with each supply-voltage terminal |
| دۆخی RoHS | RoHS3 compliant |
| Device Description | Monolithic quadruple line driver |
ڕێنمایی ڕێکخستنی پینی SN75188N 14-pdip, through hole
ڕێکخستنی پین بۆ SN75188N (پاکێجی 14-pdip, through hole). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ SN75188N.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
SN75188N گونجاوە بۆ 6 بەکارھێنانs: Legacy RS-232 Serial Port Transmission, Industrial Control and Data Acquisition, Parallel Serial Port Expansion, Test and Measurement Equipment, RS-232-to-RS-485 Communication Bridges, Legacy Computer and Peripheral Maintenance.
Legacy RS-232 Serial Port Transmission
The SN75188N fits a four-channel RS-232 transmit path where the host logic uses TTL-compatible levels and the cable requires bipolar signaling. Its four current-limited drivers operate from ±7.5 V to ±15 V and are intended to meet ANSI TIA/EIA-232-E signaling requirements. Because the IC contains drivers but no receivers, the receive side requires a separate receiver such as the MAX232NSR or an appropriate single-channel receiver. The 14-PDIP footprint is especially useful when maintaining older RS-232 adapter boards or restoring equipment with through-hole connector interfaces.
پێشنیارکراو
Industrial Control and Data Acquisition
The SN75188N is suitable for industrial interfaces that must place several logic-level commands onto RS-232 lines without using a large surface-mount transceiver footprint. Four independent channels can carry parallel commands, status signals, or multiplexed data between a controller and remote equipment. Commercial operation from 0°C to 70°C suits controlled indoor environments. Designers should confirm cable length, receiver load, and ground potential because RS-232 is a single-ended interface, and the SN75188N's current-limited outputs require the receiving equipment to provide compatible biasing.
پێشنیارکراو
Parallel Serial Port Expansion
The SN75188N can expand four legacy transmit functions where an embedded controller does not provide enough compatible RS-232 outputs. Each driver converts a logic signal into a bipolar line level suitable for a conventional DB-series serial connection. The through-hole 14-PDIP package simplifies installation in a PC expansion card or hand-built interface adapter. Because the device does not include receivers, a complete port requires additional receive channels, and system grounding should be checked to minimize common-mode voltage differences between connected equipment.
پێشنیارکراو
Test and Measurement Equipment
Instrumentation systems can use the SN75188N to drive four RS-232 control outputs from a controller with TTL or CMOS logic. The current-limited driver characteristic, approximately 10 mA typical, helps isolate the controller from cable or receiver faults, while the minimum 300-ohm power-off output impedance supports defined line states when outputs are inactive. Engineers should add the supply bypass capacitance recommended by the datasheet and verify that each output has the intended idle polarity. The commercial temperature rating limits use in hot or unheated outdoor enclosures.
پێشنیارکراو
RS-232-to-RS-485 Communication Bridges
The SN75188N can provide the computer-side RS-232 output stage of a communication bridge feeding an RS-485 transceiver such as the ADM485JNZ. In this arrangement, the SN75188N converts logic-level commands into bipolar RS-232 signals, while the differential transceiver handles noise rejection and longer cable runs. This separation avoids connecting the two bus standards directly and preserves the voltage conventions of each interface. The bridge requires careful logic-polarity translation, grounding, and isolation planning, particularly when the two cables connect equipment with different ground references.
پێشنیارکراو
Legacy Computer and Peripheral Maintenance
The SN75188N is a practical solution for repairing or extending equipment that uses four bipolar RS-232 transmit lines on a through-hole board. Its 14-PDIP package can replace an equivalent MC1488 implementation when the pin and electrical functions align, simplifying maintenance of obsolete communications adapters. The device must be installed with correct supply polarity and adequate bypass capacitors, and its 0°C to 70°C range must be checked against the enclosure temperature. For compact new products, a surface-mount transceiver is normally preferable because it combines transmit and receive functions.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ SN75188N — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | SN75C188N | MC1488P |
|---|---|---|---|
| Package | 14-PDIP, through hole | 14-PDIP, through hole | 14-PDIP, through hole |
| Brand | Texas Instruments | Texas Instruments | Motorola |
| Driver Configuration | 4/0 quadruple line driver | 4/0 quadruple line driver | 4/0 quadruple line driver |
| Interface Standard | ANSI TIA/EIA-232-E | RS-232 | RS-232 |
جیاکەرەوە سەرەکییەکان
- Four integrated legacy RS-232 transmit channels (بەراورد بەMAX232NSR)
- Through-hole 14-PDIP construction (بەراورد بەSP232EET-L/TR)
- Documented MC1488 interchangeability (بەراورد بەMC1488P)
تێبینییەکانی دیزاین
The SN75188N requires correct dual positive and negative supplies within ±7.5 V to ±15 V. Check polarity before energizing the board because reversed bipolar rails can damage the series diodes associated with the supply terminals. Place the datasheet-recommended bypass capacitance close to the supply and ground pins, and route the driver return current directly to the device ground rather than through a remote chassis-ground path.
Treat each driver output as a separate transmission line even when all four channels are routed together. Keep the traces short, avoid stubs and sharp directional changes, and connect the cable shield to chassis ground at one controlled point. Because RS-232 is single-ended, keep the logic ground and interface ground return path continuous to reduce receiver errors caused by common-mode voltage differences.
Do not substitute a generic four-channel TTL buffer for this driver. The SN75188N's approximately 10 mA current limiting, minimum 300-ohm power-off output impedance, and load-capacitance-controlled slew rate are part of its RS-232 behavior. Also verify that unused driver outputs are not left floating, and confirm that the connected receiver recognizes the idle polarity produced by the selected interface circuit.
Check the full temperature range before using this commercial-grade part in legacy equipment. The SN75188N and MC14888 family devices are characterized for 0°C to 70°C, whereas the related SN55188 is specified for -55°C to 125°C. A mechanically similar military-temperature device is not automatically an acceptable substitute unless its package, pinout, and electrical limits also match the original design.
زانیاری پابەندبوون
The product listing identifies the SN75188N as RoHS3 compliant. Additional environmental and material compliance attributes are not stated and remain unknown.