STM32F103VGT6 - 72MHz Cortex-M3 1MB MCU | STMicroelectronics
MPN: STM32F103VGT6 ✓ چالاکSTM32F103VGT6 گشتی
A microcontroller is a programmable system-on-chip that integrates a CPU core, flash memory, RAM, peripheral interfaces, and I/O in a single package. The STM32F103 family is positioned within the hierarchy of 32-bit microcontroller, ARM Cortex-M microcontroller, embedded control MCU, and semiconductor. Its USB and CAN interfaces make it suitable for connected embedded equipment, while the 1 MB flash configuration provides useful code and data storage for firmware, configuration, and protocol handling.
Key verified features include a 72 MHz maximum clock, 1 MB of 1M x 8 flash memory, a 32-bit ARM Cortex-M3 core, USB and CAN support, and a compact 100-LQFP package. The flash density distinguishes this device from lower-density STM32F103 variants and provides additional room for embedded applications. The listed package also offers a relatively large pin count for systems requiring numerous digital, analog, communications, and debug connections.
The STM32F103VGT6 belongs to STMicroelectronics' STM32F1 series and uses the Cortex-M3 instruction set architecture. Its 72 MHz operating frequency provides the timing headroom expected from the F1 performance line. Because the device integrates USB and CAN in the same MCU, an embedded product can consolidate communications functions that might otherwise require separate interface hardware, subject to firmware, electrical, and protocol validation.
Typical applications include industrial controllers, USB-connected data acquisition equipment, CAN-based industrial nodes, motor-control systems, and communication modules. Its 1 MB flash capacity is particularly useful where application firmware, bootloader code, data logs, calibration parameters, and communication stacks must coexist in external nonvolatile memory.
Designers should confirm the complete pin assignment, electrical limits, ADC characteristics, clock tree, and peripheral configuration in the official STMicroelectronics datasheet before layout release. PCB design must also preserve the package-specific land pattern and provide the required decoupling, clock, reset, and exposed-power connections specified for this device.
This page consolidates the verified distributor specifications, current sourcing information, package details, cross-reference evidence, and practical selection considerations for the STM32F103VGT6. It also distinguishes a documented pin-compatible cross-brand option from unsupported lower-density or differently packaged alternatives, helping engineers make sourcing decisions without confusing electrical similarity with a genuine drop-in replacement.
جێگرەوەکانی جێگۆڕکێ بۆ STM32F103VGT6 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ STM32F103VGT6 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package.
GD32F103VGT6
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
STM32F103VGT6 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Product Type | 32-bit ARM Cortex-M3 microcontroller |
| CPU Core | ARM Cortex-M3 |
| Architecture | 32-bit RISC |
| زۆرترین فرێکوێنسیی کاتژمێر | 72 MHz |
| Flash Memory Size | 1 MB |
| Flash Organization | 1M x 8 bits |
| Product Series | STM32F1 series |
| Device Family | STM32F103 |
| Performance Line | XL-density performance line |
| USB Interface | Supported |
| CAN Interface | Supported |
| پاکێج | 100-LQFP (14 mm x 14 mm) |
| ژمارەی پینەکان | 100 pins |
| جۆری دامەزراندن | Surface mount |
ڕێنمایی ڕێکخستنی پینی STM32F103VGT6 100-lqfp (14 mm x 14 mm)
ڕێکخستنی پین بۆ STM32F103VGT6 (پاکێجی 100-lqfp (14 mm x 14 mm)). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ STM32F103VGT6.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
STM32F103VGT6 گونجاوە بۆ 6 بەکارھێنانs: USB Data-Acquisition Controller, CAN-Based Industrial Control Node, Motor-Control Embedded Controller, Industrial Communication Gateway, Programmable Automation Controller, USB-Conditioned Embedded Control Module.
USB Data-Acquisition Controller
The STM32F103VGT6 fits USB data-acquisition equipment because it combines a 72 MHz ARM Cortex-M3 core, 1 MB of flash, and a verified USB interface. Firmware can sample, buffer, format, and expose measurement data while retaining room for application code and configuration data in the 1M x 8-bit flash array. Designers should pair the MCU with the required USB connector, protection network, clock source, and decoupling. The principal engineering benefit is consolidating USB connectivity and embedded processing in one 100-LQFP device; the trade-off is that USB timing, bus-power requirements, and firmware validation must be completed against the official electrical and peripheral documentation.
پێشنیارکراو
CAN-Based Industrial Control Node
The STM32F103VGT6 is appropriate for a CAN-based industrial control node because the verified listing identifies CAN connectivity alongside a 72 MHz Cortex-M3 core and 1 MB of flash. This combination supports protocol handling, sensor management, control logic, event logging, and local configuration within one microcontroller. Its 100-LQFP 14 mm x 14 mm package provides numerous external connections for sensors and digital I/O. Implementation still requires the correct CAN transceiver, bus protection, termination strategy, isolation where required, and firmware timing validation. The main advantage is consolidated real-time control and communication; the main limitation is that the supplied evidence does not specify detailed CAN timing or transceiver parameters.
پێشنیارکراو
Motor-Control Embedded Controller
The STM32F103VGT6 can serve as the embedded controller in a motor-control system because the STM32F1 performance line operates at 72 MHz and provides 1 MB of flash for control algorithms, parameter storage, and diagnostics. The 100-LQFP package offers a practical pin count for position inputs, PWM outputs, communications, and protection signals. A production design must verify the exact PWM channels, timer mappings, ADC characteristics, analog limits, and pin assignments in the official STMicroelectronics documentation. The benefit is high processing headroom and local nonvolatile storage in one package; the trade-off is that motor-loop timing, thermal margins, and analog measurement paths require careful validation rather than reliance on distributor summaries.
پێشنیارکراو
Industrial Communication Gateway
The STM32F103VGT6 is suitable for an industrial communication gateway that combines USB or CAN connectivity with a 72 MHz Cortex-M3 processor and 1 MB of flash. The available storage can hold a bootloader, communication stack, protocol conversion logic, configuration data, and diagnostic routines without requiring a separate nonvolatile-memory device in every design. The 100-LQFP package also supports the many digital interfaces commonly found in gateway boards. Engineering validation must cover protocol timing, connector protection, clock accuracy, brownout behavior, and firmware recovery paths. The measurable benefit versus a smaller-memory MCU is the additional 1 MB of flash; the trade-off is a larger 100-pin footprint and greater board-routing complexity.
پێشنیارکراو
Programmable Automation Controller
The STM32F103VGT6 is a practical candidate for programmable automation equipment requiring a 72 MHz control processor, 1 MB of flash, and numerous I/O connections. Its USB interface can support configuration, diagnostics, or service access, while CAN can connect the controller to a distributed industrial network. The verified 100-LQFP package is large enough for external memory-bus-style functions, timers, serial interfaces, and discrete I/O, subject to the actual pin map. Designers should preserve the correct decoupling and grounding layout and confirm every alternate function before routing the PCB. The advantage is substantial processing and storage capacity in one device; the trade-off is that the MCU requires careful pin planning and complete electrical validation.
پێشنیارکراو
USB-Conditioned Embedded Control Module
The STM32F103VGT6 can support a compact embedded control module that uses its USB interface for configuration, logging, or host communication while a 72 MHz Cortex-M3 core executes real-time control functions. The 1 MB of flash provides room for an application image, bootloader, calibration data, and communication code. The 100-LQFP package can be used on a module that exposes the required signals, although it is not physically tiny compared with smaller MCU packages. A successful design must address USB signal integrity, power-supply sequencing, clock startup, ESD protection, and firmware update security. The key benefit is integrated USB control capability and ample flash; the trade-off is a larger package and the need to verify detailed electrical limits from the manufacturer datasheet.
پێشنیارکراو
داتای سەرچاوەی ئەندازیاری بۆ STM32F103VGT6 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | GD32F103VGT6 |
|---|---|---|
| Package | 100-LQFP (14 mm x 14 mm) | 100-LQFP (14 mm x 14 mm) |
| Brand | STMicroelectronics | GigaDevice |
| CPU Core | ARM Cortex-M3 | ARM Cortex-M3 |
| Maximum Clock Frequency | 72 MHz | 108 MHz |
| Architecture | 32-bit | 32-bit |
| Pin Compatibility | Target device | Documented pin-to-pin compatible candidate |
جیاکەرەوە سەرەکییەکان
- Established STMicroelectronics device identity and firmware baseline (بەراورد بەGD32F103VGT6)
- Verified 1 MB flash configuration (بەراورد بەGD32F103VGT6)
- Single-package USB and CAN integration (بەراورد بەGD32F103VGT6)
تێبینییەکانی دیزاین
Confirm the 100-LQFP 14 mm x 14 mm land pattern and pin numbering against the official STMicroelectronics package drawing before PCB release. The verified search results identify the package but do not provide a complete numbered pin table, so assigning nets from memory risks connecting power, ground, reset, clock, or debug pins incorrectly. Place the required input and bypass capacitors close to their associated pins, provide a clean ground reference, and route high-current and sensitive signals away from switching nodes.
Design the power tree for the STM32F103VGT6 only after obtaining the official supply-voltage limits and absolute maximum ratings from the manufacturer datasheet. The supplied evidence confirms 72 MHz operation but not allowable input voltage, regulator requirements, or ADC references. Use a stable regulated source, separate analog filtering where needed, and check brownout and startup behavior for USB or CAN systems. Do not infer an LDO or core-voltage implementation from the cross-brand GD32 description, because that behavior differs.
Do not treat a pin-compatible second source as automatically production-equivalent. The GD32F103VGT6 is documented as pin-to-pin compatible, but its 108 MHz clock, zero-wait SRAM-buffered flash, internal 1.2 V LDO implementation, and ADC behavior differ from the STM32F103VGT6. Run firmware, timing, interrupt, ADC, communications, and brownout tests on both devices if the GD32 part will be approved as a second source, especially for industrial or motor-control products.
Keep the 72 MHz clock circuit short and isolate it from USB, CAN, and switching-related routes. Provide a stable clock source and follow the manufacturer's recommended input and output capacitor arrangements once the exact datasheet values are confirmed. USB traces require controlled impedance and continuous reference planes, while CAN routing should follow the selected transceiver and network-impedance requirements. Avoid placing test points or unrelated high-impedance nets where they can introduce avoidable coupling.
Estimate dissipation from the actual clock, peripherals, I/O loading, and supply voltage before deciding whether the 100-LQFP copper area is sufficient. The verified sources do not provide power dissipation or junction-temperature data, so an estimated junction temperature cannot be stated responsibly. Use the official thermal model and the PCB's actual copper and airflow conditions. At 72 MHz with many I/O active, thermal validation should include worst-case ambient temperature and sustained maximum-frequency operation rather than idle-current measurements alone.
زانیاری پابەندبوون
The supplied verified listings do not state target-part RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. These fields remain unknown until confirmed from STMicroelectronics or authoritative distributor compliance records.