STM32G031K8T6 - 64MHz Cortex-M0+ 64KB MCU | STMicroelectronics
MPN: STM32G031K8T6 ✓ چالاکSTM32G031K8T6 گشتی
A microcontroller is a semiconductor that integrates a processor core, program memory, data memory, and peripheral interfaces into one package. In the product hierarchy, a microcontroller is an integrated circuit and semiconductor device; within an embedded system, it executes firmware, reads inputs, controls outputs, and connects the application to sensors, communications equipment, and actuators. The Cortex-M0+ architecture therefore provides the computational foundation rather than acting merely as a fixed-function interface controller.
The STM32G031K8T6 combines a 64 MHz operating frequency with 64 KB of flash and 8 KB of SRAM. Its 32-bit instruction set supports efficient control workloads while its relatively small memory footprint suits compact systems. The 32-LQFP 7 mm by 7 mm package provides a conventional leaded footprint that can simplify assembly and prototype inspection compared with a very small fine-pitch package. The available verified listings also describe the part as an active embedded microcontroller.
The exact peripheral mix, voltage range, temperature ratings, timers, communication interfaces, analog features, and programming details are not present in the supplied verified excerpts. Those values are therefore not inferred or fabricated here. This page concentrates on confirmed identity and capacity information: Cortex-M0+ core, 32-bit architecture, 64 MHz maximum frequency, 64 KB flash, 8 KB RAM, and 32-LQFP 7 mm by 7 mm packaging.
The MCU is appropriate for small embedded controllers whose firmware fits within 64 KB and whose working data fits within 8 KB. Potential roles include building controls, compact industrial interfaces, low-cost sensor nodes, accessory controllers, and compact consumer devices. Final peripheral suitability should be confirmed against the complete manufacturer datasheet and the pin configuration for the 32-pin package before schematic or PCB release.
The primary design consideration is package and pinout verification. A shared package name alone does not guarantee that every peripheral signal is assigned identically between MCU variants. Engineers should compare power pins, ground pins, debug signals, boot configuration pins, and every used peripheral signal against the manufacturer package diagram. The 32-LQFP footprint also requires adequate copper and assembly clearance around its leaded package.
This page combines verified manufacturer identity, distributor specifications, source links, package facts, and careful replacement guidance. It also distinguishes documented drop-in candidates from related devices that require pinout, firmware, and peripheral-level verification, providing practical context beyond a distributor title or basic catalog listing.
جێگرەوەکانی جێگۆڕکێ بۆ STM32G031K8T6 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ STM32G031K8T6 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, SRAM, Core, Maximum CPU Frequency, RoHS Status.
STM32G051K8T6
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →STM32G071K8T6
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
STM32G031K8T7
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →STM32G031K8T6 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Manufacturer | STMicroelectronics |
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| CPU Core | Arm Cortex-M0+ |
| Architecture | 32-bit RISC |
| Maximum CPU Frequency | 64 MHz |
| Embedded Flash Memory | 64 KB (64K x 8) |
| Static RAM | 8 KB |
| پاکێج | 32-LQFP (7 mm x 7 mm) |
| ژمارەی پین | 32 pins |
| جۆری دامەزراندن | Surface Mount |
| Product Series | STM32G0 |
| Family Coverage | STM32G031x4/x6/x8 |
| Core Classification | Mainstream microcontroller |
| Program Memory Type | Embedded Flash |
| Longevity Status | Active |
ڕێنمایی ڕێکخستنی پینی STM32G031K8T6 32-lqfp (7 mm x 7 mm)
ڕێکخستنی پین بۆ STM32G031K8T6 (پاکێجی 32-lqfp (7 mm x 7 mm)). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ STM32G031K8T6.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
STM32G031K8T6 گونجاوە بۆ 6 بەکارھێنانs: Compact Industrial Control Module, Low-Cost Sensor Node, Connected Accessory Controller, Building and Environmental Control, Consumer Accessory and HMI Controller, Motor and Auxiliary Control.
Compact Industrial Control Module
STM32G031K8T6 fits compact industrial control modules that require deterministic firmware execution without a large processor or memory subsystem. Its confirmed 64 MHz Arm Cortex-M0+ core provides a 32-bit control platform, while 64 KB of embedded flash accommodates application code, configuration data, and a small bootloader. The 8 KB SRAM supports task stacks, communication buffers, and working variables, although the final memory budget must be measured with the production firmware. The 32-LQFP 7 mm by 7 mm package is practical for industrial control boards where assemblers prefer a visible leaded footprint. Before release, verify the required communication, timer, analog, and I/O channels against the complete manufacturer datasheet, and check that each selected pin is exposed on the 32-pin package.
Low-Cost Sensor Node
STM32G031K8T6 can serve as the processing core of a compact sensor node when the application fits within 64 KB of flash and 8 KB of SRAM. The 64 MHz Cortex-M0+ core is suitable for periodic sampling, local filtering, state-machine control, and data-packet preparation, while the small 7 mm by 7 mm LQFP helps reduce board footprint. A practical design should allocate SRAM carefully because 8 KB must accommodate the stack, operating-system state if used, sensor buffers, and communications storage. The supplied data does not verify the exact ADC, timer, or communication peripheral set, so engineers should confirm that the chosen sensors and radio interface use pins available on the 32-LQFP variant. Production firmware and low-power behavior should also be validated under actual environmental conditions.
Connected Accessory Controller
STM32G031K8T6 is suitable for a connected accessory controller when its 64 MHz Cortex-M0+ processing speed, 64 KB program memory, and 8 KB RAM are sufficient for local control and communication firmware. The device can execute button, indicator, and protocol-handling logic while its relatively small memory footprint supports compact hardware. The 32-LQFP package also permits straightforward routing to through-hole test points and assembly inspection. Because the supplied verified excerpts do not identify the available UART, USB, CAN, or other communication peripherals, the selected interface must be checked in the full STM32G031K8 documentation before schematic approval. Firmware developers should also assess boot behavior, pin-state defaults, and peripheral differences if the accessory is a redesign using another STM32G0 device.
Building and Environmental Control
STM32G031K8T6 can support a small building-control or environmental-monitoring node where local logic must sample inputs, operate actuators, and manage a serial interface. Its 64 MHz Cortex-M0+ core provides more than enough visible specification for compact supervisory tasks, while 64 KB flash and 8 KB SRAM constrain firmware to appropriately small designs. The 7 mm by 7 mm 32-LQFP package can be placed on a compact controller board, although designers must observe the larger footprint compared with an ultrafine-pitch MCU. The verified excerpts do not confirm the number or type of ADC channels, timers, or communication ports, so sensor compatibility must be established from the package pinout and complete datasheet. Production validation should include environmental extremes, actuator drive levels, and safe behavior during firmware faults.
Consumer Accessory and HMI Controller
STM32G031K8T6 is a candidate for a consumer accessory that performs local button handling, status control, and simple product-specific logic. Its confirmed 64 MHz Cortex-M0+ core and 32-bit instruction set suit responsive embedded tasks, and the 64 KB flash capacity is appropriate for a focused application rather than a graphics-intensive platform. The 8 KB SRAM is sufficient only for modest buffering and control logic, so developers should avoid large display-frame buffers and unnecessary protocol libraries. The 32-LQFP footprint simplifies hand assembly and visual inspection in low-volume products. Because the supplied evidence does not list the package's exposed peripheral assignments, confirm display, touch, LED, and communications signals against the manufacturer package diagram before layout release.
Motor and Auxiliary Control
STM32G031K8T6 may be evaluated for auxiliary motor-control or actuator-control tasks where the firmware must sequence commands and monitor machine state. Its 64 MHz Cortex-M0+ core provides a responsive 32-bit execution platform, while the 32-LQFP package supports conventional board routing and assembly. Suitability depends on the exact timer outputs, encoder inputs, analog sensing channels, and fault-response architecture, none of which are quantified in the supplied excerpts. These functions must therefore be verified from the complete manufacturer datasheet rather than inferred from the family name. For safety-relevant or high-current motion, treat the MCU as a supervisory controller unless the required interfaces and protection mechanisms are documented. Validate timing, watchdog behavior, thermal margin, and safe-state outputs on the final hardware.
داتای سەرچاوەی ئەندازیاری بۆ STM32G031K8T6 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | STM32G051K8T6 | STM32G071K8T6 | STM32G031K8T7 |
|---|---|---|---|---|
| Package | 32-LQFP (7 mm x 7 mm) | 32-LQFP (7 mm x 7 mm) | 32-pin PQFP package | 32-LQFP (7 mm x 7 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Product Class | Mainstream Arm Cortex-M0+ MCU | STM32G0-series microcontroller | STM32G0-series microcontroller | Mainstream Arm Cortex-M0+ MCU |
| Verified Alternative Status | Target device | Listed as a known equivalent | Listed as a compatible alternative requiring pinout checks | Same-family ordering variant; ordering-table validation required |
جیاکەرەوە سەرەکییەکان
- Directly documented target identity and capacity (بەراورد بەSTM32G071K8T6)
- Known-equivalent designation in the supplied cross-reference data (بەراورد بەSTM32G051K8T6)
- Same-platform ordering option within the G031 family (بەراورد بەSTM32G031K8T7)
تێبینییەکانی دیزاین
Create the land pattern from the manufacturer drawing for the 32-LQFP 7 mm by 7 mm package rather than inferring it from the generic package name. Confirm pin-1 orientation, pin numbering, lead width, pitch, and courtyard dimensions against the complete STM32G031K8 datasheet. Because the supplied excerpts do not provide a verified pin table, do not route power, ground, debug, boot, or peripheral signals until the official package diagram has been checked.
Follow the manufacturer reference schematic for input and internal core-decoupling capacitors once those values are available from the complete datasheet. The MCU contains an internal supply for digital peripherals, SRAM, and flash according to the supplied family PDF excerpt, but the exact VCORE implementation and bypass requirements are package-dependent. Do not copy capacitor values from an unrelated STM32 model; verify the power-supply limits and decoupling network for the STM32G031K8T6 ordering code.
Do not treat a shared package as proof of drop-in compatibility. Even when two MCUs use 32-pin packages, their power, ground, debug, boot, and peripheral pins can differ. For every proposed replacement, compare the official pin tables, alternate-function mappings, clock requirements, flash wait-state limits, peripheral inventory, interrupt names, register compatibility, and programming procedure. A successful board boot and peripheral smoke test are still required after a hardware substitution.
Plan the board around the leaded 32-LQFP footprint, including adequate solder-joint and inspection clearance. Place required bypass capacitors adjacent to their associated supply pins and route sensitive signals away from high-current switching paths. Preserve accessible test points for the debug interface, reset behavior, and power rails so production troubleshooting can be performed without redesigning the assembly.
زانیاری پابەندبوون
The supplied verified excerpts do not state the target's RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. These fields remain unknown rather than being inferred from the manufacturer or package.