STM32G071K8U6 - 64MHz Cortex-M0+ 64KB Flash 32-UFQFPN MCU | STMicroelectronics
MPN: STM32G071K8U6 ✓ چالاکSTM32G071K8U6 گشتی
A microcontroller is a single-chip computer that integrates a CPU core, Flash program memory, SRAM, and peripherals such as ADCs, timers, and communication interfaces onto one die. The STM32G0 series sits in the mainstream Arm Cortex-M tier of STMicroelectronics' STM32 portfolio, positioned between entry-level 8-bit devices and higher-density STM32F/G4 families for cost-sensitive embedded control.
Key features of the STM32G071K8U6 include a 64 MHz maximum core frequency, 36 KB of SRAM for data buffering, and 64 KB of embedded Flash for firmware storage. The device supports three core supply rails at 1.8 V, 2.5 V, and 3.3 V, which lets one design cover both industrial 3.3 V systems and lower-voltage battery-powered nodes. Mixed-signal resources include a 12-bit ADC and high-resolution timers suitable for motor, dimming, and sensor acquisition loops.
Architecturally, the STM32G071 family pairs the low-cost Cortex-M0+ core with STMicroelectronics' STM32G0 peripherals, including fast GPIO, hardware CRC, and an extended set of timers. Because the core is Cortex-M0+, firmware built for the STM32G0 toolchain stays compact while retaining the standard Arm exception model and a broad ecosystem of drivers and middleware.
Typical applications include general-purpose industrial control boards, motor and stepper drive controllers, LED lighting and dimming modules, small sensor-hub nodes, compact consumer accessories, and smart-home peripherals that need a small footprint with plenty of I/O in a 5 x 5 mm package.
When designing around this device, plan decoupling close to each supply pin, keep the exposed thermal pad soldered with a dedicated ground pour for heat spreading, and confirm that the 32-pin UFQFPN land pattern and the 5 x 5 mm footprint match your PCB library before committing to layout.
This page consolidates manufacturer specifications, distributor availability, drop-in alternatives from the same STM32G0 family, and practical design notes that go beyond a single datasheet link, helping engineers qualify the STM32G071K8U6 for a new embedded design in one place.
جێگرەوەکانی جێگۆڕکێ بۆ STM32G071K8U6 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ STM32G071K8U6 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Flash Memory, SRAM, Series, RoHS Status.
STM32G071KBU6
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →STM32G071KBU6N
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
STM32G081KBU6
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →STM32G071KBU7
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
STM32G071KBU3
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →STM32G071K8U7
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
STM32G071K8U6 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Core | Arm Cortex-M0+ 32-bit RISC |
| Maximum CPU Frequency | 64 MHz |
| Flash Memory | 64 KB (64K x 8) |
| SRAM | 36 KB |
| پاکێج | 32-UFQFPN (5 x 5 mm) |
| Number of I/O Pins | Up to 28 (8x U datasheet: 4x 5-pin...) |
| Supply Voltage Range | 1.8 V / 2.5 V / 3.3 V |
| Architecture | Arm Cortex-M0+ (Thumb-2 instruction set) |
| جۆری دامەزراندن | Surface Mount |
| Product Line | STM32G0 series - STM32G071x8/xB mainstream line |
| Manufacturer | STMicroelectronics |
| Ordering Temperature Grade | -40 C to +85 C (grade 6) |
| ADC Resolution | 12-bit |
| Timer / PWM Resources | Advanced-control and general-purpose timers with PWM output |
| دۆخی RoHS | Compliant |
| Lead-Free / Halogen-Free Processing | Yes |
| Operating Voltage (I/O) | Same as core supply: 1.8 V to 3.6 V class operation |
ڕێنمایی ڕێکخستنی پینی STM32G071K8U6 32-ufqfpn (5 x 5 mm)
ڕێکخستنی پین بۆ STM32G071K8U6 (پاکێجی 32-ufqfpn (5 x 5 mm)). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ STM32G071K8U6.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
STM32G071K8U6 گونجاوە بۆ 6 بەکارھێنانs: Stepper and BLDC Motor Control, LED Lighting and Dimming Modules, Industrial Sensor Hub Node, Smart Home and Consumer Accessories, Power Supply and Battery Management Control, Consumer and Industrial HMI Controller.
Stepper and BLDC Motor Control
The STM32G071K8U6 fits compact motor-drive modules because it combines 64 MHz Cortex-M0+ processing with advanced-control timers that generate complementary PWM and dead-time insertion for half-bridge stages. The 12-bit ADC samples shunt current and rotor position at rates adequate for current regulation, while 36 KB of SRAM holds PWM compare arrays, capture buffers, and a speed-control loop without spilling into external memory. With up to 28 I/O in a 5 x 5 mm UFQFPN, the board can host three-phase gate-drive signalling, an encoder or Hall-sensor input, and CAN-free serial diagnostics in a very small footprint, and the 1.8 V to 3.3 V supply range simplifies powering from both 5 V-reduced and 3.3 V rails.
پێشنیارکراو
LED Lighting and Dimming Modules
LED drivers built on the STM32G071K8U6 use hardware PWM channels to dim constant-current channels independently, and the 64 MHz core leaves ample headroom for flicker-free refresh rates and open-load detection. The 12-bit ADC can be used to monitor the LED string voltage and temperature for derating, and the large number of I/O pins in the 32-pin UFQFPN package leaves room for multiple channel enables, fault flags, and a communications header. Because the device operates down to 1.8 V, it also fits battery-powered portable lighting where a 3.3 V LDO output is not available, and the same Cortex-M0+ ecosystem lets the same firmware stack drive both mains-connected and low-voltage fixtures.
پێشنیارکراو
Industrial Sensor Hub Node
A compact sensor-hub node built around the STM32G071K8U6 can poll several analogue and digital sensors, filter the readings, and publish them over a serial link while staying within a very small power budget. The 64 KB of Flash holds the acquisition firmware, calibration tables, and a bootloader, and the 36 KB of SRAM is enough for time-series buffering and digital filtering of the 12-bit ADC channels. The 32-pin UFQFPN (5 x 5 mm) footprint is valuable in DIN-rail and panel-mount enclosures where board area is limited, and the 1.8 V / 2.5 V / 3.3 V options let the node share a supply with industrial sensor buses running at 24 V through a regulator.
پێشنیارکراو
Smart Home and Consumer Accessories
Compact consumer accessories such as doorbell chimes, thermostat remotes, and smart plugs benefit from the STM32G071K8U6's combination of 64 KB Flash, 36 KB SRAM, and a 5 x 5 mm package, which allows the whole control board to fit behind a small plastic fascia. The low-cost Cortex-M0+ core handles touch, button, and LED feedback while the 12-bit ADC monitors a potentiometer, thermistor, or ambient light sensor, and the wide supply range supports both 3.3 V USB-powered and 1.8 V coin-cell-derived rails. Wireless modules can be interfaced over UART or SPI, while the fast GPIO and hardware timers support relay, buzzer, and stepper mechanisms without additional logic.
پێشنیارکراو
Power Supply and Battery Management Control
In power-supply and battery-management products, the STM32G071K8U6 serves as the supervisory and sequencing controller, using its timer outputs to ramp converters in a defined order and its ADC to supervise bus voltage and current. The 64 MHz core is fast enough to run a digital power factor correction state machine or a lithium-ion pack balancing routine, and the 36 KB of SRAM accommodates per-cell measurement buffers. Because the device starts at 1.8 V, it can supervise and control low-voltage rails directly after a single-cell Li-ion source without an intermediate regulator, while the 32-pin package leaves enough pins for a pre-charge contactor, charge-pump enable, and fault outputs.
پێشنیارکراو
Consumer and Industrial HMI Controller
A small human-machine interface controller for appliances, kiosks, and instrumentation panels can use the STM32G071K8U6 to drive displays and read controls in a single 5 x 5 mm footprint. Its GPIO count supports segment or SPI display interfaces, keypad scanning, and encoder inputs simultaneously, while the 12-bit ADC handles analog knobs and thermistor-based temperature compensation. With 64 KB of Flash for UI fonts and logic plus 36 KB of SRAM for display buffering, the design avoids an external co-processor, and the 1.8 V to 3.3 V operation lets the same board be reused across low-voltage handheld and 24 V panel-mounted products after regulation.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ STM32G071K8U6 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | STM32G071KBU6 | STM32G071KBU6N | STM32G081KBU6 | STM32G071KBU7 | STM32G071KBU3 | STM32G071K8U7 |
|---|---|---|---|---|---|---|---|
| Package | UFQFPN-32 (5x5) with exposed pad | UFQFPN-32 (5x5) - same | UFQFPN-32 (5x5) - same | UFQFPN-32 (5x5) - same | UFQFPN-32 (5x5) - same | UFQFPN-32 (5x5) - same | UFQFPN-32 (5x5) - same |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| CPU Core | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum Frequency | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz | 64 MHz |
| Flash Memory | 64 KB (64K x 8) | 128 KB (+100%) | 128 KB (+100%) | 128 KB (+100%) | 128 KB (+100%) | 128 KB (+100%) | 64 KB (identical) |
| SRAM | 36 KB | 36 KB | 36 KB | 36 KB | 36 KB | 36 KB | 36 KB |
| Supply Voltage | 1.8 V / 2.5 V / 3.3 V | 1.8 V / 2.5 V / 3.3 V | 1.8 V / 2.5 V / 3.3 V | 1.8 V / 2.5 V / 3.3 V | 1.8 V / 2.5 V / 3.3 V | 1.8 V / 2.5 V / 3.3 V | 1.8 V / 2.5 V / 3.3 V |
| Temperature Grade | -40 C to +85 C (grade 6) | -40 C to +85 C (grade 6) | -40 C to +85 C (grade 6) | -40 C to +85 C (grade 6) | -40 C to +105 C (grade 7) | -40 C to +85 C (grade 3) | -40 C to +105 C (grade 7) |
| ADC | 12-bit ADC | 12-bit ADC | 12-bit ADC | 12-bit ADC, expanded analog resources | 12-bit ADC | 12-bit ADC | 12-bit ADC |
| Series / Positioning | STM32G0 mainstream, STM32G071x8 | STM32G0 mainstream, 128 KB Flash grade | STM32G0 mainstream, 128 KB Flash grade | STM32G0 enhanced analog line | STM32G0 mainstream, extended temperature | STM32G0 mainstream, 128 KB Flash grade | STM32G0 mainstream, 64 KB Flash, extended temperature |
جیاکەرەوە سەرەکییەکان
- Mainstream STM32G0 density in a very small footprint (بەراورد بەSTM32G0B1RET6)
- Direct same-footprint upgrade path with double the Flash (بەراورد بەSTM32G071KBU6)
- Single package covers multiple supply rails and temperature grades (بەراورد بەSTM32G071KBU7)
- Broader analog and connectivity option when the design outgrows the mainstream line (بەراورد بەSTM32G081KBU6)
تێبینییەکانی دیزاین
The STM32G071K8U6 uses a 5 x 5 mm UFQFPN with an exposed pad that is the device ground connection. Place a 100 nF ceramic decoupling capacitor at each supply pin with the shortest possible ground return, and flood the exposed pad with a dedicated ground pour connected by multiple vias to the ground plane. Check the land pattern in the STMicroelectronics package drawing against your PCB library, because UFQFPN pitch and pad dimensions are easy to transpose incorrectly from a generic QFN-32 footprint.
Estimated: at a 64 MHz core frequency with a 3.3 V supply and typical Cortex-M0+ active current of roughly 6 mA, the digital core draws on the order of 20 mW. In contrast, each analogue peripheral adds measurable load - the 12-bit ADC sampling continuously can add several milliamps of supply current. Because the device supports 1.8 V operation, running the core at 1.8 V while keeping the ADC referenced appropriately lowers dissipation and improves battery life in portable designs.
Route analog inputs (ADC channels) away from fast switching nodes and from the 64 MHz clock net, and reference the analog ground to the quietest point of the ground plane. Keep the crystal or external oscillator (if used) close to the oscillator pins with a grounded guard via and no traces beneath it. For motor and LED dimming designs, separate the power stage return path from the MCU ground and tie them at a single star point near the supply entry to keep switching current out of the sensitive analog references.
Two frequent errors: first, assuming the KBU6 substitution is free - it carries 128 KB of Flash, so dual-bank or bootloader layouts that depend on a specific memory map must be re-checked; second, overlooking that the '6' suffix denotes the -40 C to +85 C grade while the '7' suffix covers -40 C to +105 C, which matters in automotive-adjacent or hot industrial enclosures. Also confirm the full pin list in the STMicroelectronics datasheet, including which pins are supply versus alternate-function, before finalising the board layout.
زانیاری پابەندبوون
STMicroelectronics ships the STM32G0 mainstream line in RoHS-compliant, lead-free and halogen-free packages. AEC-Q100 qualification is not stated for this ordering code; confirm with the manufacturer if an automotive-grade variant is required. REACH and conflict-minerals declarations are not published in the product listings and should be confirmed on request.