STMicroelectronics

STM8L152K6T3 - 16MHz 32KB Low-Power MCU | STMicroelectronics

MPN: STM8L152K6T3 ✓ چالاک
1.8 V to 3.6 V Vdss 32-LQFP (7 x 7 mm) Package 16 MHz Speed 32 KB (32K x 8) Memory
MOQ: 1 |

STM8L152K6T3 گشتی

STMicroelectronics STM8L152K6T3 is an 8-bit ultra-low-power STM8L EnergyLite microcontroller with a 16 MHz clock, 32 KB Flash memory, and a 32-LQFP 7 x 7 mm package. It combines 1 KB of data EEPROM with an RTC, LCD interface, timers, USART, I2C, SPI, ADC, DAC, and comparators in an energy-conscious 8-bit platform.

An ultra-low-power microcontroller is designed to maintain accurate measurement, communication, and control functions while minimizing energy use during active operation and standby. The STM8L family belongs to the broader hierarchy of embedded MCU, microcontroller, and semiconductor devices. Low-power architecture is especially useful in battery-operated equipment where the time spent waiting for an event can dominate overall energy consumption.

The STM8L152K6T3 provides 32 KB of Flash for program storage, 1 KB of EEPROM for nonvolatile data, and operation from 1.8 V to 3.6 V. Its peripheral set includes an RTC for timekeeping, an ADC and comparators for analog measurements, a DAC for analog output, and USART, I2C, and SPI interfaces for external sensors, memory, and host connectivity. The LCD interface supports compact user-interface designs.

This is a CISC-based 8-bit MCU built for compact embedded systems rather than high-throughput applications. Its 16 MHz operating frequency supports control-loop and communications tasks while its low-power operating modes help reduce average consumption. The medium-density STM8L15x family is specified over 1.8 V to 3.6 V and includes temperature grades from -40 °C to +85 °C and -40 °C to +125 °C depending on the exact ordering code.

Typical applications include low-power sensor nodes, compact industrial monitoring equipment, battery-powered instruments, LCD-driven user interfaces, data loggers, and connected control modules. The ADC and comparators suit threshold detection, while the RTC and EEPROM can retain timestamps and calibration data between power cycles. Serial interfaces allow the MCU to connect measurement hardware to a host or external memory.

Design around the MCU's low-power modes by defining which peripherals can remain active in each operating mode. Keep analog and communication traces short, provide the decoupling required by the manufacturer datasheet, and confirm pin multiplexing before assigning LCD, ADC, DAC, or serial functions. Verify the selected ordering code against the required temperature grade and production design.

This product page combines the principal device specifications with package guidance, pinout-status documentation, selection trade-offs, and a focused comparison with same-family drop-in options. It is intended to help engineers evaluate memory, voltage, interface, and temperature requirements before committing the STM8L152K6T3 to a PCB design.

جێگرەوەکانی جێگۆڕکێ بۆ STM8L152K6T3 — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ STM8L152K6T3 (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Flash Memory, CPU Architecture, LCD Interface, Product Type.

STMicroelectronics
Flash Memory: 16 KB
بەراوردکردن لەگەڵ STM8L152K6T3 →
STMicroelectronics
Package: 32-LQFP, 7 x 7 mm
Flash Memory: 32 KB
بەراوردکردن لەگەڵ STM8L152K6T3 →
STMicroelectronics
Package: 32-pin LQFP
بەراوردکردن لەگەڵ STM8L152K6T3 →
STMicroelectronics
Package: 32-pin LQFP, 7 x 7 mm
CPU Architecture: 8-bit CISC
LCD Interface: Integrated LCD support
بەراوردکردن لەگەڵ STM8L152K6T3 →
STMicroelectronics
Package: 32-pin LQFP, 7 x 7 mm
CPU Architecture: 8-bit CISC
LCD Interface: Integrated LCD support
بەراوردکردن لەگەڵ STM8L152K6T3 →
STMicroelectronics
Package: 32-pin LQFP, 7 x 7 mm
Flash Memory: 32 KB
CPU Architecture: 8-bit
بەراوردکردن لەگەڵ STM8L152K6T3 →

STM8L152K6T6

✅ جێگرەوەی ڕاستەوخۆ
STMicroelectronics
📦 32-LQFP (7 x 7 mm)
8-bit ultra-low-power microcontroller (MCU) · STMicroelectronics · 16 MHz · 8-bit · 32 KB · 1 KB · 3.6 V to V at power-down · 125 °C

پەیوەندی بۆ نرخ

بینینی داتاشیت →

STM8L151K6T3

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
STMicroelectronics
📦 32-LQFP (7 x 7 mm)
8-bit ultra-low-power microcontroller · STM8L EnergyLite · 16 MHz · 32 KB · 32K x 8 bits · 1 KB · 1.8 V to 3.6 V · Down to 1.65 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

STM8L151K6T6

✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوە
STMicroelectronics
📦 32-LQFP (7 x 7 mm)
8-bit ultra-low-power microcontroller · STM8L EnergyLite · STM8L151x4/6 medium-density series · 16 MHz · 32 KB (32K x 8) · 2 KB · 1 KB · 1.8 V to 3.6 V

پەیوەندی بۆ نرخ

بینینی داتاشیت →

STM8L152K6T3 زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان

Product Type 8-bit ultra-low-power microcontroller
Series STM8L EnergyLite
زۆرترین فرێکوێنسیی کاتژمێر 16 MHz
Flash Memory 32 KB (32K x 8)
Data EEPROM 1 KB
Operating Voltage Range 1.8 V to 3.6 V
Power-Down Voltage 1.65 V
Architecture 8-bit CISC
پاکێج 32-LQFP (7 x 7 mm)
ژمارەی پین 32 pins
جۆری دامەزراندن Surface mount
Temperature Grade Options in STM8L15x Family -40 °C to +85 °C or -40 °C to +125 °C
Real-Time Clock Yes
LCD Interface Yes
Timers Yes
USART Yes
I2C Interface Yes
SPI Interface Yes
ADC Yes
DAC Yes
Comparators Yes

ڕێنمایی ڕێکخستنی پینی STM8L152K6T3 32-lqfp (7 x 7 mm)

ڕێکخستنی پین بۆ STM8L152K6T3 (پاکێجی 32-lqfp (7 x 7 mm)). ئەم IC ی دیجیتاڵە GPIO، ڕووکارەکانی پەیوەندی (UART، SPI، I2C) و پینی وزە لەخۆدەگرێت. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ فەنکشنەکانی پینی جێگرەوە و ھەڵبژاردنەکانی ڕێکخستن. پێویستە بۆ دیزاینی سیستەمی جێگیر و ڕێکخستنی PCB.

نەخشەی پینئاوتی پاکێجی 32-lqfp (7 x 7 mm) بۆ STM8L152K6T3

هیچ داتای وردی پینئاوت بەردەست نییە بۆ STM8L152K6T3.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

STM8L152K6T3 گونجاوە بۆ 6 بەکارھێنانs: Battery-Powered Sensor Node, LCD Instrument Panel, Industrial Condition Monitor, Battery-Powered Data Logger, Low-Power Communication Module, Smart Home Control Module.

⚡

Battery-Powered Sensor Node

The STM8L152K6T3 fits battery-powered sensor nodes because it combines a 16 MHz 8-bit core, low-power family architecture, and operation from 1.8 V to 3.6 V. Its ADC can acquire sensor signals, while comparators can perform threshold detection without requiring every measurement to be processed continuously. The RTC and 1 KB EEPROM support timestamps, operating counters, and retained calibration data. A low-duty-cycle firmware strategy can use the MCU's low-power modes between events, reducing the energy required when the node is idle.

📺

LCD Instrument Panel

The STM8L152K6T3 is well suited to a compact LCD instrument panel because it includes an LCD interface alongside timers, ADC, DAC, and comparators. Its 32 KB Flash can hold display formatting, calibration, event handling, and communication firmware, while the 16 MHz clock supports responsive control updates. A sensor front end can feed the ADC and comparators, and the DAC can generate an analog reference or test signal. Verify display segment requirements, bias voltage, and alternate-function assignments against the manufacturer pin table.

🏭

Industrial Condition Monitor

The STM8L152K6T3 can support industrial condition-monitoring equipment that must measure analog signals while maintaining compactness and low power use. Its ADC handles sensor acquisition, comparators support threshold detection, and the RTC timestamps events. USART, I2C, and SPI provide options for connecting local memory, transducers, or an upstream controller. The 32-LQFP package measures 7 x 7 mm, making it practical for space-constrained monitor boards, although the exact operating-temperature grade and EMC design must match the deployment environment.

🖥️

Battery-Powered Data Logger

The STM8L152K6T3 is appropriate for a low-duty-cycle data logger that periodically records sensor information and returns to sleep. Its 32 KB of Flash supports firmware and local buffering, while the 1 KB EEPROM can retain counters, calibration coefficients, or a fault history across power cycles. The RTC provides timekeeping for sample stamps, and I2C or SPI can connect serial flash or external memory. Using the 1.8 V to 3.6 V operating range can support compact battery systems, with average consumption determined primarily by wake-up frequency and active acquisition time.

🌐

Low-Power Communication Module

The STM8L152K6T3 can act as the control element in a compact low-power communication module because it includes USART, I2C, and SPI alongside a 16 MHz 8-bit processor. These interfaces can connect a radio or sensor module, external memory, and an auxiliary controller while the MCU manages packet handling and power state. Its low-power family positioning is valuable in remote endpoints that spend most of their time waiting for data. The 32 KB Flash should be checked against firmware size, including drivers, protocol stack, and application logic.

🧩

Smart Home Control Module

The STM8L152K6T3 fits a smart-home control module that coordinates sensors, local indicators, and an external network interface. The LCD interface can support a compact status display, while ADC and comparator inputs can detect analog conditions. I2C is useful for sensors and configuration devices, SPI for faster peripherals, and USART for a host or radio link. Its 32 KB Flash and 1 KB EEPROM provide useful embedded storage, and the compact 32-LQFP footprint helps minimize board area. Firmware should keep unused peripherals disabled during idle periods to maximize battery life.

What is the STM8L152K6T3?
The STM8L152K6T3 is an 8-bit ultra-low-power STM8L EnergyLite microcontroller operating at up to 16 MHz, with 32 KB of Flash, 1 KB of EEPROM, and a 32-LQFP package. According to the STMicroelectronics product listing, it also integrates an RTC, LCD interface, timers, USART, I2C, SPI, ADC, DAC, and comparators for compact embedded and battery-powered systems.
What are the key specifications of STM8L152K6T3 that engineers should know?
The STM8L152K6T3 combines a 16 MHz maximum clock with 32 KB of Flash, 1 KB of data EEPROM, and operation from 1.8 V to 3.6 V. According to the manufacturer product listing, its 32-LQFP package is 7 x 7 mm, and the integrated peripherals include an RTC, LCD, timers, USART, I2C, SPI, ADC, DAC, and comparators. It is positioned for low-power embedded control rather than high-performance processing.
Where can I download the STM8L152K6T3 datasheet PDF?
The STM8L152K6T3 datasheet PDF is accessible through the linked STMicroelectronics datasheet entry, which points to the official document download. The listed document covers the STM8L152K6T3 and its family characteristics. Use the manufacturer datasheet for the authoritative pin-description table, electrical limits, memory map, and recommended application circuit before completing PCB or firmware design.
Where is the STM8L152K6T3 pinout located?
The STM8L152K6T3 pinout should be located in the package and pin-description section of the STMicroelectronics manufacturer datasheet. This page identifies the physical device as a 32-LQFP package with 32 pins, but a complete numbered pin list is not published here. Use the datasheet pin table and package drawing to assign power, ground, reset, clock, LCD, analog, and serial functions.
What is the operating voltage of STM8L152K6T3?
The STM8L15x family operates from 1.8 V to 3.6 V and can continue in power-down operation down to 1.65 V. According to the STM8L152K6T3 and STM8L152K6T6 comparison information, this voltage range applies to the medium-density STM8L151x4/6 and STM8L152x4/6 family. Confirm individual minimum and maximum operating conditions against the manufacturer datasheet.
Is the STM8L152K6T3 suitable for battery-powered devices?
Yes, the STM8L152K6T3 is suitable for battery-powered devices because it belongs to the STM8L ultra-low-power family and includes low-power-oriented peripherals. Its 1.8 V to 3.6 V operating range supports low-voltage systems, while the RTC allows timekeeping during low-duty-cycle operation. Actual battery life depends on the selected operating mode, wake-up rate, and active peripheral load.
What can replace the STM8L152K6T3?
The closest documented drop-in replacement is the STMicroelectronics STM8L152K6T6, which uses the same 32-LQFP footprint and belongs to the same medium-density STM8L152x4/6 family. The ordering-code distinction requires careful review of temperature grade and production qualification. The STM8L151K6T3 and STM8L151K6T6 are same-family candidates, but peripheral and application suitability must be checked before substitution.
Is STM8L152K6T3 the same as STM8L152K6T6?
The STM8L152K6T3 and STM8L152K6T6 are closely related STM8L152K6 devices in the same 32-LQFP family, but their ordering codes may select different temperature grades. According to the published comparison information, the STM8L15x family includes -40 °C to +85 °C and -40 °C to +125 °C grades. Verify the exact grade, qualification status, and lifecycle requirements before treating them as interchangeable.
STM8L152K6T3 vs STM8L152K6T6 — which is better for industrial use?
STM8L152K6T6 is generally the stronger candidate when the design requires the -40 °C to +125 °C STM8L15x temperature grade, while STM8L152K6T3 should be selected only when its specified grade satisfies the application. Both provide 16 MHz operation, 32 KB Flash, and a 32-LQFP package. Confirm the exact ordering-code temperature range in the STMicroelectronics datasheet.
When should I choose STM8L152K6T3 over STM8L151K6T6?
Choose STM8L152K6T3 when the design specifically needs the STM8L152 feature set, including its LCD-related functionality and the peripheral complement associated with that family member. STM8L151K6T6 may be considered when its available peripherals meet the design and its ordering-code grade is acceptable. The published comparison notes that the STM8L15x peripheral sets are modular, so software and pin-function differences require review.
Is STM8L152K6T3 suitable for an LCD sensor display application?
Yes, the STM8L152K6T3 is suitable for compact LCD-driven sensor displays because it includes an LCD interface alongside an ADC, comparators, timers, and serial interfaces. Its 32 KB Flash and 16 MHz clock provide resources for display handling and sensor-control firmware. Actual segment count, display voltage, and pin mapping must be confirmed from the manufacturer datasheet for the chosen LCD.
What peripherals does the STM8L152K6T3 include?
The STM8L152K6T3 includes an RTC, LCD interface, timers, USART, I2C, SPI, ADC, DAC, and comparators. According to the STMicroelectronics product information, these peripherals support timekeeping, local display, analog measurement and output, threshold detection, and serial communication. The precise channel counts, alternate functions, and electrical limits should be taken from the manufacturer datasheet.
How much Flash and EEPROM does STM8L152K6T3 have?
The STM8L152K6T3 provides 32 KB of Flash, organized as 32K x 8, and 1 KB of data EEPROM. According to the STMicroelectronics product listing, the Flash stores the program while the EEPROM retains data independently of volatile RAM. The EEPROM is useful for calibration constants, counters, configuration values, or timestamps in low-power equipment.
Where can I buy STM8L152K6T3 and request current lead time?
Use the Request a Quote form on this page to request the STM8L152K6T3, current lead time, minimum order quantity, and available packaging. The device is listed as active by the manufacturer distribution information. A formal quotation is the appropriate channel for current commercial terms, production allocation, and shipment scheduling for this exact ordering code.
What is the price of STM8L152K6T3?
Current commercial terms for the STM8L152K6T3 should be requested through the Request a Quote form on this page. The form allows an engineer or buyer to specify quantity, package, and shipment requirements while receiving the latest quotation from XAIPART. This avoids publishing a stale unit price or treating a distributor listing as a guaranteed quotation for the exact ordering code.
Is STM8L152K6T3 in stock and what is its lead time?
Current stock and lead time for STM8L152K6T3 should be confirmed through the Request a Quote form on this page. The manufacturer lifecycle information identifies the STM8L152K6T3 as active, but active status alone does not guarantee immediate inventory for every quantity. Include your required quantity, date code, and target delivery schedule in the request.

داتای سەرچاوەی ئەندازیاری بۆ STM8L152K6T3 — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose the STM8L152K6T3 for compact, low-power 8-bit designs that need 32 KB Flash, 1 KB EEPROM, a 16 MHz core, an RTC, an LCD interface, and mixed serial and analog peripherals. Select the STM8L152K6T6 when it provides the required ordering-code temperature grade and qualification while retaining the same 32-LQFP footprint. The STM8L151K6T3 or STM8L151K6T6 may fit when the application does not depend on STM8L152-specific LCD or analog functions, but their peripheral mapping and exact grade must be verified. The STM8L152K6U6 belongs to the same controller family but uses another package, so it cannot replace the target without PCB changes. Before finalizing any choice, confirm pin multiplexing, memory requirements, temperature limits, and the complete manufacturer pin table.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە STM8L152K6T6 STM8L151K6T3 STM8L151K6T6
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package 32-LQFP (7 x 7 mm) 32-LQFP (7 x 7 mm) 32-LQFP (7 x 7 mm) 32-LQFP (7 x 7 mm)
Maximum Clock Frequency 16 MHz 16 MHz 16 MHz 16 MHz
Flash Memory 32 KB (32K x 8) 32 KB (32K x 8) 32 KB 32 KB
Data EEPROM 1 KB 1 KB 1 KB 1 KB
Operating Voltage Range 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V 1.8 V to 3.6 V
RTC Yes Yes Yes Yes
Serial and Analog Peripherals USART, I2C, SPI, ADC, DAC, and comparators USART, I2C, SPI, ADC, DAC, and comparators USART, I2C, SPI, ADC, DAC, and comparators USART, I2C, SPI, ADC, DAC, and comparators

جیاکەرەوە سەرەکییەکان

  • Exact 32-LQFP family replacement with matching core resources (بەراورد بەSTM8L152K6T6)
  • Retains the STM8L152 peripheral set for LCD and mixed-signal designs (بەراورد بەSTM8L151K6T3)
  • Compact low-power integration in a 7 x 7 mm footprint (بەراورد بەSTM8L152K6U6)

تێبینییەکانی دیزاین

Estimated power behavior depends on the selected operating mode, clock frequency, and enabled peripherals. Use the manufacturer current tables to calculate average consumption from the duty cycle of active measurement, communication, and sleep intervals. Disable unused clocks and peripherals before entering low-power modes, and retain the RTC only when timestamp accuracy is required. Validate the battery budget at the highest expected temperature and communication activity.

Place the decoupling capacitors specified by the manufacturer datasheet directly beside the corresponding power-supply pins, with a short and low-inductance return path. Keep analog inputs and the ADC or comparator circuitry away from switching nodes and fast SPI traces where practical. Route the 32-LQFP exposed-area and pad geometry exactly to the manufacturer land pattern rather than adapting a generic 32-pin footprint.

Assign every LCD, ADC, DAC, comparator, USART, I2C, and SPI function from the official alternate-function table before fixing the PCB netlist. Several peripheral functions can share pins, so a schematic-level peripheral priority decision may be necessary. Keep oscillator and reset routing short, avoid placing test points that add capacitance to sensitive pins, and follow the package drawing for pin-1 orientation and lead geometry.

Do not select a replacement solely from the family name or package. Confirm the exact ordering-code temperature grade, Flash configuration, peripheral set, pin multiplexing, and qualification requirements. A mechanically similar MCU may boot correctly but fail to expose the LCD, DAC, comparator, or alternate serial function used by the original design. Review the manufacturer pin and peripheral tables before approving a substitution.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

Compliance status must be confirmed from the current manufacturer product documentation or declaration for the exact ordering code.

داتا پشتڕاستکراوەتەوە لە: 2026-11-04 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

STM8L152K6T3 datasheet STM8L152K6T3 pinout STM8L152K6T3 datasheet pdf STM8L152K6T3 specifications STM8L152K6T3 equivalent STM8L152K6T3 replacement STM8L152K6T3 drop-in replacement STM8L152K6T3 vs STM8L152K6T6 STM8L152K6T3 price STM8L152K6T3 stock STMicroelectronics STM8L152K6T3 STM8L152K6T3 32-LQFP pinout STM8L152K6T3 low power application what is STM8L152K6T3

پێکهاتە و زاراوە پەیوەندیدارەکان

STMicroelectronics STM8L152K6T3 STM8L152K6T6 STM8L151K6T3 STM8L151K6T6 STM8L EnergyLite STM8L15x 8-bit microcontroller ultra-low-power MCU embedded microcontroller CISC architecture 16 MHz clock 32 KB Flash 1 KB EEPROM real-time clock RTC LCD interface USART I2C SPI ADC DAC comparator 32-LQFP LQFP package surface-mount device SMD battery-powered sensor node industrial condition monitoring
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ