Texas Instruments

THS6093ID - 275mA +12V ADSL Line Driver | Texas Instruments

MPN: THS6093ID ✓ چالاک
+12 V Vdss 275 mA Id 14-pin SOIC, 0.154 inch body width, 3.90 mm width Package
MOQ: 1 |

THS6093ID گشتی

Texas Instruments THS6093ID is a dual-channel, high-speed ADSL CPE line driver rated for 275 mA output current and +12 V operation in a 14-pin SOIC package. The device is intended for driving signals from the remote terminal toward the central office in asymmetric digital subscriber line systems, including full-rate ADSL and G.Lite configurations.

An ADSL line driver is a specialized interface-circuit component that converts upstream driver signals into robust, high-current line outputs suitable for copper telephone networks. It sits within the power-management and signal-conditioning hierarchy of a customer premises equipment design, translating logic-level commands into line-side waveforms while helping preserve signal integrity across the transformer-coupled network.

Key features include a wide supply-voltage range, suitability for single +12 V operation, compatibility with a 1:2 transformer ratio, and low 2.1 pA/√Hz noninverting current noise. The THS6093 also provides low total harmonic distortion of -72 dBc while driving the line and includes shutdown control. Each channel draws only 7.3 mA of supply current, helping limit the power burden of a multi-output access circuit.

The device uses two noninverting outputs in a 14-pin SOIC package. Its high output-current capability is important for ADSL line interfaces because the external transformer, network loading, and cable losses can require substantially more current than a conventional logic driver. The specified 275 mA rating provides the core design limit for transformer selection, copper-line loading, supply capability, and thermal analysis.

Typical uses include full-rate ADSL customer premises equipment, G.Lite ADSL line interfaces, and power-line carrier line-driver circuits. In each application, the THS6093 can operate from a single +12 V rail and drive the line through an appropriate external transformer while the shutdown function provides a controlled path for reducing activity when the endpoint is inactive.

The primary design consideration is ensuring that the +12 V supply, output-current demand, transformer ratio, load, thermal conditions, and signal-integrity expectations all agree. Use the manufacturer datasheet pin-description table when assigning PCB nets, and confirm that the selected transformer supports the specified 1:2 ratio and operating bandwidth.

جێگرەوەکانی جێگۆڕکێ بۆ THS6093ID — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ THS6093ID (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Total Harmonic Distortion.

Texas Instruments
Package: 8-pin SOIC (D)
Product Type: Dual ADSL CPE and DSL line driver
Total Harmonic Distortion: -72 dBc driving a 25 ohm load at 2 Vpp
بەراوردکردن لەگەڵ THS6093ID →
Texas Instruments
Package: 8-pin SOIC (D)
Product Type: Dual ADSL CPE and DSL line driver
Total Harmonic Distortion: -72 dBc driving a 25 ohm load at 2 Vpp
بەراوردکردن لەگەڵ THS6093ID →

THS6093IDRG4

✅ جێگرەوەی ڕاستەوخۆ
📦 14-SOIC
Same 14-SOIC package, terminals, and stated performance characteristics; delivery format differs from the THS6093ID tube ordering option

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

THS6093ID تایبەتمەندییەکان

Product Type Dual ADSL CPE and PLC line driver
Output Current 275 mA
Nominal Supply Voltage +12 V
ئێستای دابینکردن 7.3 mA per channel
Number of Driver Channels 2
Noninverting Current Noise 2.1 pA/√Hz
Total Harmonic Distortion -72 dBc while driving
Transformer Compatibility 1:2 transformer ratio
Shutdown Function Yes
Supported Applications Full-rate ADSL, G.Lite ADSL, and PLC line driving
پاکێج 14-pin SOIC, 0.154 inch body width, 3.90 mm width
جۆری دامەزراندن Surface mount
Packaging Tube

ڕێنمایی ڕێکخستنی پینی THS6093ID 14-pin soic, 0.154 inch body width, 3.90 mm width

ڕێکخستنی پین بۆ THS6093ID (پاکێجی 14-pin soic, 0.154 inch body width, 3.90 mm width). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی 14-pin soic, 0.154 inch body width, 3.90 mm width بۆ THS6093ID

هیچ داتای وردی پینئاوت بەردەست نییە بۆ THS6093ID.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

THS6093ID گونجاوە بۆ 6 بەکارھێنانs: Full-Rate ADSL CPE Line Interface, G.Lite ADSL Terminal Interface, Power-Line Carrier Line Driver, Central Office Line-Side Interface, Remote Terminal Equipment Line Output, Copper Network Access Card.

🌐

Full-Rate ADSL CPE Line Interface

The THS6093ID fits a full-rate ADSL customer premises equipment line driver because it provides two 275 mA-capable outputs, operates from a single +12 V supply, and supports the required 1:2 transformer ratio. Each channel consumes 7.3 mA of supply current, which helps control the power requirement of the dual-channel interface. Its specified 2.1 pA/√Hz noninverting current noise and -72 dBc distortion support waveform quality at the line driver stage. Place the device close to the external transformer and follow the manufacturer decoupling and routing guidance to limit supply disturbance and preserve high-speed signal integrity.

📶

G.Lite ADSL Terminal Interface

The THS6093ID is suitable for a G.Lite ADSL terminal interface where reduced-rate operation requires a robust copper-line output stage. The device supports full-rate ADSL and G.Lite applications and can use a single +12 V supply, avoiding the need for a split positive and negative line-driver rail. Its two-channel architecture allows a compact implementation when the design drives two related line outputs. The 275 mA output rating, 7.3 mA supply current per channel, and specified 2.1 pA/√Hz noise density make it possible to balance line-drive capability against board space and power use.

⚡

Power-Line Carrier Line Driver

The THS6093ID can serve as a power-line carrier line driver because it combines a 275 mA output-current capability with low noninverting current noise of 2.1 pA/√Hz. The device supports a single +12 V operating rail and includes shutdown control, allowing the interface to be disabled when the communication channel is not required. Its -72 dBc total harmonic distortion specification is valuable when preserving waveform quality through the coupling network. The external coupling or transformer network remains application-specific, so validate its ratio, bandwidth, loading, and isolation against the manufacturer interface guidance.

🏢

Central Office Line-Side Interface

The THS6093ID can be evaluated for a central-office line-side interface where compact, high-current driver capability is needed. Two channels in a 14-pin SOIC reduce board area compared with separate single-channel implementations, while 7.3 mA supply current per channel supports a practical multi-channel power budget. Its 275 mA output rating must be reconciled with the transformer, cable length, line impedance, and worst-case operating condition. Because shutdown and output behavior are central to line-interface management, use the manufacturer pin and application descriptions when defining the interface topology.

📡

Remote Terminal Equipment Line Output

The THS6093ID is appropriate for remote terminal equipment that drives a signal from the customer premises toward the central office. Its noninverting output arrangement simplifies the drive path for compatible line-interface circuitry, while the 1:2 transformer compatibility provides a defined starting point for network-coupling design. The 275 mA capability accommodates the current demanded by the line interface, but the actual operating point must include transformer losses and network loading. Shutdown control can reduce activity during inactive periods, while the low-noise and low-distortion characteristics support transmission quality.

🖥️

Copper Network Access Card

A copper network access card can use the THS6093ID when it requires two high-current line-driver outputs in a limited PCB area. The 14-pin SOIC package is compatible with conventional surface-mount assembly, and the dual-channel configuration consolidates related line-drive functions. Single +12 V operation simplifies the principal power rail, while 7.3 mA per channel provides a starting point for thermal and supply budgeting. The design must still reserve adequate routing and component placement for the external transformer, input/output return paths, and supply decoupling recommended for reliable high-speed line transmission.

کورتەی بەرهەمە پێشنیارکراوەکان

THS6093ID Texas Instruments بەکارهێنراوە لە: Full-Rate ADSL CPE Line Interface, G.Lite ADSL Terminal Interface, Power-Line Carrier Line Driver, Central Office Line-Side Interface, Remote Terminal Equipment Line Output, Copper Network Access Card THS6093IDRG4 Pin-compatible ordering option for the same line-driver function بەکارهێنراوە لە: Full-Rate ADSL CPE Line Interface, G.Lite ADSL Terminal Interface, Power-Line Carrier Line Driver, Central Office Line-Side Interface, Remote Terminal Equipment Line Output, Copper Network Access Card
What is THS6093ID?
THS6093ID is a Texas Instruments dual-channel ADSL CPE and power-line carrier line driver designed for +12 V operation. According to the Texas Instruments datasheet, the device uses two noninverting outputs, supports a 1:2 transformer ratio, and is packaged in a 14-pin SOIC. It is intended for driving line-side signals between remote terminal equipment and a central office in ADSL systems.
What are the key specifications of THS6093ID that engineers should know?
The THS6093ID provides two driver outputs, a 275 mA output-current rating, and operation from a single +12 V supply. According to the Texas Instruments datasheet, it also offers 2.1 pA/√Hz noninverting current noise, -72 dBc total harmonic distortion while driving, 7.3 mA supply current per channel, shutdown control, and compatibility with a 1:2 transformer ratio in a 14-pin SOIC package.
Where can I download the THS6093ID datasheet PDF?
The official THS6093 product page is the preferred starting point for the THS6093ID datasheet, pin description, ordering information, and quality documentation. The Texas Instruments product page is located at https://www.ti.com/product/THS6093. Use the datasheet's pin-description table when assigning PCB nets and review its absolute-maximum-rating section before finalizing the +12 V supply design.
Where can I find the THS6093ID pinout?
The THS6093ID pinout is defined in the pin-description table of the manufacturer datasheet for the 14-pin SOIC package. Do not infer the complete pin assignments from general interface-circuit examples because the shutdown connection, supply pins, grounds, and channel outputs must be wired exactly as specified. The manufacturer product page for THS6093 provides access to the technical documentation and package information.
How much output current can THS6093ID deliver?
THS6093ID is rated for 275 mA output current. According to the Texas Instruments datasheet, that rating is central to its use as an ADSL line driver because line output requirements depend on transformer selection, cable loading, signal amplitude, and operating conditions. Designers should compare the complete load demand with 275 mA rather than treating the rating as a continuous-current specification for every operating mode.
Can THS6093ID operate from a single 12 V supply?
Yes, THS6093ID is designed for single +12 V operation. According to the Texas Instruments datasheet, each channel draws 7.3 mA of supply current. The supply system must nevertheless support the combined channel demand, output-current requirement, line-load behavior, and board-level thermal conditions. Confirm the permitted supply-voltage range and decoupling requirements in the manufacturer datasheet before releasing the power design.
What is the noise performance of THS6093ID?
THS6093ID has a specified noninverting current noise density of 2.1 pA/√Hz. According to the Texas Instruments datasheet, it also delivers -72 dBc total harmonic distortion while driving the ADSL line. These characteristics make the device relevant to line-interface designs where waveform distortion and added current noise can degrade signal quality or downstream receiver performance.
Does THS6093ID support full-rate ADSL and G.Lite?
Yes, THS6093ID is identified as being suitable for both full-rate ADSL and G.Lite applications. According to the Texas Instruments datasheet, the device can drive signals from the remote terminal toward the central office in asymmetric digital subscriber line systems. It also supports power-line carrier line-driver use and can operate from a single +12 V supply through a compatible external transformer.
What transformer ratio should be used with THS6093ID?
THS6093ID is compatible with a 1:2 transformer ratio. According to the Texas Instruments datasheet, the external transformer is an essential part of the line-driver interface and influences current demand, signal amplitude, bandwidth, and isolation. The 1:2 compatibility requirement should be applied together with the specified 275 mA output-current capability and the actual copper-line loading.
THS6093ID vs THS6093IDRG4 - which is the better replacement?
THS6093IDRG4 is a same-manufacturer drop-in option with the same 14-SOIC package and described terminal and functional consistency as THS6093ID. According to the FindIC cross-reference information, the replacement does not require modification of the existing board. The primary distinction is the packaging format: THS6093ID is identified in tube packaging, while the RG4 ordering code uses a different delivery format.
What is the best drop-in replacement for THS6093ID?
THS6093IDRG4 is the directly identified drop-in replacement for THS6093ID because it retains the 14-SOIC package, matching terminals, and consistent main performance characteristics. The cross-reference information states that PCB modification is not required. When changing the ordering code, confirm the required assembly method and verify all production documents against the manufacturer datasheet before substitution.
When should I choose THS6093ID over THS6093IDRG4?
Choose THS6093ID when the assembly process accepts tube packaging, and choose THS6093IDRG4 when the production line requires the alternative reel-style delivery format. Both parts use the same 14-SOIC package and are described as functionally and terminally consistent, so the decision is primarily manufacturing logistics rather than a change to the electrical design.
Is THS6093ID suitable for an ADSL CPE line interface?
Yes, THS6093ID is specifically suitable for an ADSL customer premises equipment line interface. Its 275 mA output-current rating, single +12 V operation, 2.1 pA/√Hz noninverting current noise, and -72 dBc distortion specification align with the requirements of a high-speed copper-line driver. The external transformer and board layout must follow the manufacturer application guidance.
What are the best Texas Instruments equivalent for THS6093ID?
THS6093IDRG4 is the best-supported Texas Instruments equivalent because the cross-reference information identifies identical package dimensions, terminals, and main performance characteristics, with no board modification required. No comparably documented cross-brand pin-compatible alternative is established for this exact device, so engineers should avoid assuming that a generic high-current line driver has identical shutdown, noise, or transformer-interface behavior.
Where can I buy THS6093ID online and what is its price?
Use the Request a Quote form on this page to request THS6093ID availability, current commercial terms, and a lead-time quotation. The structured pricing area can be updated as channel and quantity information changes. For design qualification, request the exact THS6093ID ordering code and tube packaging requirement so the quote matches the intended assembly process.
What is the lead time for THS6093ID?
The current lead time for THS6093ID should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, package format, manufacturing conditions, and supplier inventory. Provide the required quantity, tube packaging requirement, target delivery date, and any permitted manufacturer-approved alternates when submitting the request.
Is THS6093ID currently in stock?
Current THS6093ID inventory should be confirmed through the Request a Quote form on this page. A distributor listing can change without notice, so do not treat a historical stock quantity as a guaranteed allocation. Specify the quantity, tube packaging requirement, production date, and acceptable lead time to obtain a current supply confirmation.

داتای سەرچاوەی ئەندازیاری بۆ THS6093ID — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose THS6093ID when the design requires the specified dual-channel ADSL CPE or PLC line-driver function and the assembly process accepts tube packaging. Its 275 mA output rating, +12 V operation, 1:2 transformer compatibility, shutdown function, 2.1 pA/√Hz current-noise density, and -72 dBc distortion make it appropriate for high-speed copper-line interfaces. Choose THS6093IDRG4 when the assembly line requires the alternate delivery format; the matching 14-SOIC package, terminals, and functional characteristics allow a drop-in substitution. Neither option should be selected solely by footprint for a different line-driver function. Confirm shutdown polarity, output requirements, transformer design, supply range, thermal conditions, and production documentation against the manufacturer datasheet before release.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە THS6093IDRG4
Package 14-SOIC 14-SOIC
Brand Texas Instruments Texas Instruments
Product Type Dual ADSL CPE and PLC line driver Same functional characteristics and terminals as THS6093ID
Output Current 275 mA 275 mA consistent with THS6093ID
Nominal Supply Voltage +12 V +12 V consistent with THS6093ID
Driver Channels 2 2 consistent with THS6093ID
Supply Current 7.3 mA per channel 7.3 mA per channel consistent with THS6093ID
Noninverting Current Noise 2.1 pA/√Hz 2.1 pA/√Hz consistent with THS6093ID
Total Harmonic Distortion -72 dBc while driving -72 dBc while driving consistent with THS6093ID
Transformer Ratio Compatible with 1:2 Compatible with 1:2 consistent with THS6093ID

جیاکەرەوە سەرەکییەکان

  • Direct THS6093ID replacement without PCB changes (بەراورد بەTHS6093IDRG4)
  • High-current dual line-drive capability (بەراورد بەTHS6093IDRG4)
  • Low-noise and low-distortion line output (بەراورد بەTHS6093IDRG4)

تێبینییەکانی دیزاین

Design the +12 V supply around the combined requirements of both channels and the worst-case line load. Each channel draws 7.3 mA of supply current, but the external transformer and line network determine the switching and current demand at the outputs. Verify the 275 mA rating against actual load, pulse behavior, and temperature rather than treating it as a universal continuous-current allowance.

Use the manufacturer datasheet pin-description table when assigning the 14-SOIC footprint and follow its application layout for input, output, supply, ground, and shutdown routing. Keep the line-driver outputs and their associated return paths compact, and place decoupling and signal-conditioning components close to their relevant pins. Poor high-speed return-current paths can increase distortion even when the regulator and external transformer are correctly selected.

Do not select a generic high-current line driver solely by package size. The THS6093ID's suitability depends on its 275 mA rating, 1:2 transformer compatibility, 2.1 pA/√Hz current noise, -72 dBc distortion while driving, and shutdown behavior. Check the exact ordering code and packaging format during production release to avoid mixing requirements between THS6093ID and THS6093IDRG4.

Estimated: the conductor dissipation is P = I² × R, using the actual output-current waveform and effective copper-network resistance. Apply the calculated dissipation to the relevant device and transformer thermal model, then apply the manufacturer ambient and junction-temperature limits. Because no exact thermal-resistance data are stated here, request those values from the datasheet before sizing copper area or specifying a thermal solution.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

No explicit environmental or automotive qualification statements were identified for THS6093ID.

داتا پشتڕاستکراوەتەوە لە: 2026-11-04 — داتا لەلایەن تیمی ئەندازیاری پێکھاتەکانی XAIPART پشتڕاستکراوەتەوە و ڕێکخراوە

گەڕانە پەیوەندیدارەکان

THS6093ID THS6093ID datasheet THS6093ID datasheet pdf THS6093ID pinout THS6093ID specifications THS6093ID equivalent THS6093ID replacement THS6093ID vs THS6093IDRG4 Texas Instruments THS6093ID THS6093ID price THS6093ID stock THS6093ID 14-SOIC THS6093ID ADSL line driver THS6093ID 275mA line driver

پێکهاتە و زاراوە پەیوەندیدارەکان

Texas Instruments THS6093 THS6093ID THS6093IDRG4 ADSL G.Lite ADSL power-line carrier line driver customer premises equipment interface IC semiconductor current-mode driver noninverting current noise total harmonic distortion transformer 1:2 transformer ratio +12 V power supply shutdown control 14-pin SOIC SOIC package family surface-mount package copper telephone line central office remote terminal equipment
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ