TJA1051T/E - High-Speed CAN Transceiver in SOIC-8 | NXP
MPN: TJA1051T/E ✓ چالاکTJA1051T/E گشتی
A CAN transceiver is the physical-layer component between a digital CAN controller and a two-wire differential network. The TJA1051T/E converts controller logic into CANH and CANL bus signals and converts differential bus voltages into a receive signal for the controller. It belongs to the CAN physical-layer transceiver hierarchy within interface ICs, where controllers implement the data-link protocol and transceivers handle electrical signaling, bus dominance, fault tolerance, and electromagnetic behavior.
The TJA1051 is described by NXP as a third-generation high-speed CAN transceiver. Its principal features include differential transmission and reception, an enable input, enhanced electromagnetic compatibility, and electrostatic-discharge protection. The TJA1051T/E ordering variant uses the SOIC-8 package, while the TJA1051T/3 variant provides a VIO connection for direct interfacing with 3 V to 5 V microcontrollers. Circuit designs must therefore verify the function and electrical level of pin 5 for the selected orderable variant rather than treating every TJA1051 suffix as interchangeable.
The transceiver operates in automotive and industrial environments where the CAN bus must maintain signal integrity through wiring, connectors, common-mode voltage excursions, and electromagnetic interference. Its low electromagnetic emission and high immunity characteristics help reduce interference with neighboring electronic systems. The enable function permits the host microcontroller to place the transceiver into a low-current state when it is not needed, supporting power management and fault-isolation strategies.
Typical uses include vehicle body-control modules, engine controllers, gateways, instrumentation, industrial automation controllers, diagnostic equipment, and embedded CAN networks. In these systems, the TJA1051T/E works with a CAN protocol controller rather than replacing the controller itself. The controller generates and interprets CAN frames, while the transceiver conditions the physical bus signals and provides bus-fault protection at the interface boundary.
Designers should use the manufacturer's pin-description and application information when assigning PCB tracks, especially for pin 5 on the TJA1051T/E enable variant. CANH and CANL require the correct bus termination, common-mode choke, protection network, and routing geometry. Supply and ground connections should be decoupled close to the device, and the bus interface should be checked against the required common-mode range, transient immunity, and maximum data rate.
This product record combines NXP device positioning, verified distributor identification, SOIC-8 package information, a strict drop-in comparison set, and practical CAN-interface design guidance. It also distinguishes electrical substitution from a true PCB-level replacement by highlighting the enable-versus-VIO issue that affects several superficially similar TJA1051 variants.
جێگرەوەکانی جێگۆڕکێ بۆ TJA1051T/E — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TJA1051T/E (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Product Type, Bus Interface, Automotive Qualification, Controller Interface.
NCV7342
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TLE9251V
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TCAN1042VDRQ1
✅ جێگرەوەی ڕاستەوخۆ✓ بەردەستە
$0.33923 / یەکە
بینینی داتاشیت →TCAN1051VDRQ1
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →MCP2562FD-E/SN
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TJA1051T/E تایبەتمەندییەکان
| Product Type | High-speed CAN transceiver |
| CAN Interface | Differential transmit and receive |
| Bus Structure | Two-wire CAN bus |
| CAN Physical-Layer Standard | ISO 11898-2:2003 |
| پاکێج | 8-pin SOIC |
| Enable Input | Yes, on pin 5 |
| Unpowered Bus Behavior | Passive behavior on the CAN bus |
| Microcontroller Interface | Direct 3 V to 5 V interface for TJA1051T/3 and TJA1051TK/3 variants |
| Electro-Magnetic Emission | Low EME |
| Electro-Magnetic Immunity | High EMI immunity |
| Electrostatic Discharge Protection | Enhanced ESD protection |
| Automotive Qualification | Designed for high-speed CAN applications in the automotive industry |
| دۆخی چرخەی ژیان | Active |
ڕێکخستنی پینی TJA1051T/E
| پین 1 | TXD — Transmit data input from the CAN controller |
| پین 2 | GND — Ground connection |
| پین 3 | VCC — Transceiver supply connection |
| پین 4 | RXD — Receive data output to the CAN controller |
| پین 5 | EN — Enable input for the TJA1051T/E ordering variant |
| پین 6 | CANL — CAN low bus output and input |
| پین 7 | CANH — CAN high bus output and input |
| پین 8 | GND — Ground connection |
بەکارهێنانە باوەکان
TJA1051T/E گونجاوە بۆ 6 بەکارھێنانs: Automotive Body-Control Module, Vehicle Engine and Powertrain Controller, Industrial Automation Controller, Vehicle CAN Gateway, Diagnostic and Service Equipment, Embedded CAN Sensor Network.
Automotive Body-Control Module
The TJA1051T/E fits a body-control module that connects door modules, lighting controllers, seat electronics, and diagnostic equipment to a high-speed CAN network. Its differential transmit and receive functions provide the physical-layer interface between the local CAN controller and the two-wire bus. The enable input allows the host controller to control the transceiver's operating state, while low EME, high EMI immunity, and enhanced ESD protection help maintain reliable communication in an electrically noisy vehicle environment. The 8-pin SOIC package also supports compact mixed-signal control boards. CANH and CANL routing, termination, common-mode choke selection, and transient protection should be designed from the manufacturer's application guidance.
پێشنیارکراو
Vehicle Engine and Powertrain Controller
A powertrain or engine controller can use the TJA1051T/E as the physical-layer interface between its CAN controller and vehicle network nodes. The transceiver's passive behavior when the supply is off helps avoid unintended bus activity during reset, sleep, or power-transition periods, while the pin 5 enable function gives the controller explicit control over the interface state. Enhanced EMC and ESD characteristics are valuable when the controller is mounted near relays, ignition drivers, pumps, and other high-energy loads. Engineers should verify the exact suffix, supply range, common-mode limits, and transceiver timing for the targeted vehicle platform before production release.
پێشنیارکراو
Industrial Automation Controller
The TJA1051T/E can serve as the CAN physical layer in industrial automation equipment that connects sensors, motor controllers, remote I/O, and service tools. Its high EMI immunity and low EME support operation near contactors, variable-frequency drives, switching power supplies, and long field wiring. The enable input permits firmware to disable the transceiver when a subsystem is idle, while passive unpowered behavior helps maintain bus integrity during controller reset. The SOIC-8 package simplifies assembly in compact control boards. Industrial use still requires confirmation of temperature rating, isolation strategy, surge protection, grounding, and applicable functional-safety or sector requirements.
پێشنیارکراو
Vehicle CAN Gateway
In a CAN gateway, the TJA1051T/E bridges a processor's CAN controller to another vehicle network segment. The differential receiver converts bus-level signals into a logic-level RXD output, while the transmitter drives CANH and CANL according to the controller's TXD command. Low EME is particularly useful where multiple ECUs share a wiring harness, and the enable input supports controlled interface shutdown during diagnostics or firmware transitions. Because gateways often terminate or split bus segments, engineers must carefully review termination placement, stub lengths, common-mode voltage, loop delay, and protection devices for each network segment.
پێشنیارکراو
Diagnostic and Service Equipment
The TJA1051T/E can be used in a CAN diagnostic tool that needs to connect a PC or embedded controller to an automotive network. Its high-speed CAN physical layer supports regular communication, while the enable input can be driven during tool initialization and shutdown to avoid unwanted transmitter activity. Passive behavior with the supply off is useful when the diagnostic adapter is unplugged or its power rail collapses. A practical implementation requires galvanic-isolation review, recessive-state verification, proper termination, protected connector design, and compatibility testing with the vehicle network's data rate and fault-recovery behavior.
پێشنیارکراو
Embedded CAN Sensor Network
A compact CAN sensor network can place the TJA1051T/E between an embedded microcontroller and a two-wire bus carrying environmental, pressure, or equipment-monitoring data. The SOIC-8 footprint supports compact sensor nodes, and the enable input allows a duty-cycled node to reduce current consumption between communication periods. Low EME improves compatibility with sensitive analog measurement circuits and radio equipment sharing the enclosure, while high EMI immunity supports reliable reception in industrial environments. The bus network still needs correct termination at both physical ends, controlled stub lengths, suitable common-mode filtering, and protection appropriate to the installation environment.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ TJA1051T/E — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | NCV7342 | TLE9251V | TCAN1042 | TCAN1051V | MCP2562FD |
|---|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | NXP Semiconductors | onsemi | Infineon Technologies | Texas Instruments | Texas Instruments | Microchip Technology |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN transceiver | CAN FD-capable transceiver | CAN FD-capable transceiver |
| Nominal Data-Rate Class | High-speed CAN | 1 Mbit/s class | 1 Mbit/s class | 1 Mbit/s | Up to 5 Mbit/s CAN FD class | Up to 5 Mbit/s CAN FD class |
| Bus Interface | Two-wire differential CANH/CANL | Two-wire differential CAN | Two-wire differential CAN | Two-wire differential CAN | Two-wire differential CAN | Two-wire differential CAN |
| Standby or Low-Power Control | Enable input on pin 5 | Standby function; exact pin behavior requires verification | Sleep mode; exact pin behavior requires verification | Standby function | Enable and standby-related controls | Standby control |
| CAN FD Support | No | No | No | No | Yes | Yes |
جیاکەرەوە سەرەکییەکان
- Native enable control for the NXP third-generation CAN transceiver (بەراورد بەTCAN1051V)
- Focused high-speed CAN functionality without CAN FD overhead (بەراورد بەMCP2562FD)
- Third-generation EMC and ESD positioning (بەراورد بەTJA1050T)
- Explicit enable input for host-controlled low-current operation (بەراورد بەTCAN1042)
تێبینییەکانی دیزاین
Do not interchange the TJA1051T/E with the TJA1051T/3 based only on the SOIC-8 package. The E variant places an enable input on pin 5, whereas the /3 variant places VIO there for direct 3 V to 5 V microcontroller interfacing. This 100% pin-function difference can leave the enable network in an undefined state or prevent a 3 V controller from communicating correctly. Confirm the full ordering code and reassign or isolate pin 5 before using any alternative in an existing layout.
Place the transceiver's supply and ground connections close to the device, and route the CANH and CANL pair as a compact differential pair with a consistent geometry. Keep the bus-side protection components close to the connector and away from the sensitive logic-side pins. The PCB should preserve a return-path reference plane under the bus traces, and CANH and CANL should not be routed around unrelated split planes. Follow the manufacturer's application guidance for common-mode filtering and protection placement.
Drive the pin 5 enable input only with a signal that remains defined while the transceiver supply is ramping. The enable function is useful for placing the CAN interface into a low-current state, but an uncontrolled or floating control input can produce unexpected operating behavior during reset. Define the state through the host controller, a pull network, or another mechanism compatible with the device's logic thresholds, and verify both normal and power-loss transitions using the manufacturer's recommended test sequence.
Use two 120-ohm termination resistors only at the physical ends of the CAN segment, and evaluate whether the selected transceiver, common-mode choke, and protection network alter the effective bus impedance. Avoid long branch stubs and unnecessary test-point loops because they can increase reflections and reduce signal margin. For automotive or industrial wiring, validate the complete bus network with the longest cable, connector, and grounding configurations expected in service, including transient and loss-of-ground conditions.
The SOIC-8 package is compact, so power loss at the transceiver and the heat generated by nearby regulators can raise the assembly temperature even when the IC itself is not the hottest component. Use the manufacturer dissipation and junction-temperature limits to evaluate the intended supply voltage, CAN-bus activity, and ambient range. Place thermal copper around the device where layout permits, avoid enclosing it in an unventilated enclosure next to a heat source, and verify the assembled board under maximum bus traffic rather than relying only on idle-current estimates.
زانیاری پابەندبوون
NXP describes the TJA1051 family as designed for automotive high-speed CAN applications, but the verified product information does not explicitly state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status.