TJA1055T - 125 kBd Fault-Tolerant CAN Transceiver | NXP | SOIC-14
MPN: TJA1055T ✓ چالاکTJA1055T گشتی
A CAN transceiver is the physical-layer device in a Controller Area Network link. It sits between the CAN protocol controller inside a microcontroller and the differential bus wiring, converting controller logic levels into balanced bus-line signals and, in the opposite direction, converting received bus states into a clean logic-level receive output. In the classification hierarchy it is an interface IC, specifically a CAN interface or CAN bus transceiver, a member of the broader transceiver and interface IC family used in automotive and industrial communication networks.
Key features of the TJA1055T include its enhanced fault-tolerant bus-line interface, its optimization for low-speed in-car communication, and its pin-to-pin compatibility with the earlier TJA1054 and TJA1054A devices, which allows an upgrade of an existing design without a board change. The fault-tolerant architecture is the defining improvement over the predecessor family, adding protection against faults that occur on the bus lines during operation.
Technically, the device operates with the standard differential CAN signalling scheme in which the two bus lines are dominant and recessive states rather than fixed levels. Because the TJA1055T is specified for low-speed networks up to 125 kBd, it is intended for body, comfort and convenience sub-networks rather than for powertrain or chassis high-speed CAN links, where devices rated for 1 Mbit/s or more are normally chosen. The 14-pin SOIC package is a standard surface-mount footprint that simplifies assembly and rework in automotive electronics manufacturing.
Typical applications include body control units, door and seat modules, climate control units, window and lighting controllers, passenger-comfort CAN sub-networks, vehicle diagnostic interfaces, low-speed CAN gateways for industrial and building systems, and CAN bus test and monitoring equipment.
When laying out the design, place the transceiver close to the bus connector, keep the CANH and CANL traces short and matched, provide the required bus termination resistors at the physical ends of the segment, and decouple the supply pins close to the device to limit conducted noise on the bus. Confirm that the transceiver variant selected matches the supply and bus configuration of the target network before releasing the layout.
This page consolidates the manufacturer description, verified distributor listings, drop-in replacement candidates and practical integration guidance for the TJA1055T in one place, so engineers can qualify the part and plan a sourcing strategy without searching through multiple listings and cross-reference tools.
جێگرەوەکانی جێگۆڕکێ بۆ TJA1055T — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TJA1055T (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Fault Tolerance, Interface Function, Product Type.
TJA1055T/3/C,518
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1055T/CM,118
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1055T/1J
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TJA1054T/VM,518
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1054AT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TJA1055T تایبەتمەندییەکان
| Transceiver Type | CAN bus transceiver, half (CANH/CANL differential bus lines) |
| Data Rate Support | up to 125 kBd (low-speed CAN) |
| Fault Tolerance | Enhanced fault-tolerant bus-line interface |
| Intended Application | Low-speed in-car communication networks (passenger cars) |
| ژمارەی پینەکان | 14 pins |
| پاکێج | SOIC-14 / SOP-14 surface-mount package |
| جۆری دامەزراندن | Surface mount |
| Manufacturer | NXP Semiconductors |
| Pin Compatibility | Pin-to-pin compatible with TJA1054 and TJA1054A |
| Order Code Variants | TJA1055T/1, TJA1055T/3, TJA1055T/CM,118, TJA1055T/3/C,518 |
ڕێنمایی ڕێکخستنی پینی TJA1055T soic-14 / sop-14 surface-mount package
ڕێکخستنی پین بۆ TJA1055T (پاکێجی soic-14 / sop-14 surface-mount package). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ TJA1055T.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
TJA1055T گونجاوە بۆ 6 بەکارھێنانs: Automotive Body Control Units, Door, Seat and Climate Comfort Modules, Low-Speed CAN Diagnostics Interfaces, Industrial and Building CAN Gateways, CAN Bus Test and Monitoring Equipment, Vehicle Comfort and Lighting Subsystems.
Automotive Body Control Units
The TJA1055T suits body and comfort CAN sub-networks running at up to 125 kBd, where the enhanced fault-tolerant bus-line interface protects the node against faults that appear on the CANH and CANL wiring during vehicle operation. A body control unit coordinating central locking, window lifters and lighting on one low-speed CAN segment benefits from the fault-tolerant behaviour that the manufacturer added relative to the TJA1054 family, while the 14-pin SOIC package matches standard automotive surface-mount assembly. The transceiver operates between the vehicle CAN controller and the two-wire bus, driving dominant and recessive states and returning a logic-level receive signal to the controller. Because the part targets in-car low-speed communication, it should not be used on powertrain domains that run above 125 kBd.
پێشنیارکراو
Door, Seat and Climate Comfort Modules
Door modules, seat controllers and climate control units are typical users of a low-speed CAN physical layer, because these distributed comfort functions exchange short control and status frames rather than bulk data. The TJA1055T provides the physical-layer interface for such modules, offering the enhanced fault-tolerant CAN transceiver in a compact 14-pin SOIC package with an exposed arrangement suited to automated assembly. Because these modules sit at the end of CAN segments, correct termination and stub length are critical, and the fault-tolerant behaviour of the TJA1055 helps the node remain operational when a bus line is shorted to ground or battery. The 125 kBd limit matches the traffic profile of comfort networks and keeps the design simple and cost effective.
پێشنیارکراو
Low-Speed CAN Diagnostics Interfaces
Diagnostic and gateway hardware that links a service tool to an in-vehicle low-speed CAN segment needs a physical layer that tolerates wiring faults and still recovers cleanly from bus errors. The TJA1055T, described by the manufacturer as an enhanced fault-tolerant CAN transceiver intended for low-speed in-car communication up to 125 kBd, is well suited to building such a tester or a bench interface to a body CAN network. The 14-pin SOIC footprint keeps the interface board compact and easy to rework, and the receive-data output feeds directly into a controller or an MCU such as the STM32F103 series for frame handling. Because the segment is short and inside the vehicle, keep the transceiver close to the connector and terminate the segment at its far end to avoid reflections.
پێشنیارکراو
Industrial and Building CAN Gateways
CAN gateways and building automation controllers frequently expose a low-speed CAN segment to an IP or serial backhaul, and the physical layer must survive long cables and imperfect terminations. The TJA1055T provides a compact 14-pin SOIC CAN interface for such bridges, with the enhanced fault-tolerant bus-line behaviour reducing the impact of wiring faults in building installations where cable routing is less controlled than in a vehicle. The 125 kBd operating target matches the modest traffic rates of monitoring and control data. For gateway designs that must also handle higher-rate CAN segments or galvanic isolation across a building boundary, the TJA1057GTKZ or the ISO1042BDWR are the appropriate companion choices, and the same SOIC footprint keeps the layout uniform across the board.
پێشنیارکراو
CAN Bus Test and Monitoring Equipment
Bus analyzers, loaders and monitoring tools used during vehicle or production-line validation need a physical layer that can sit on a live low-speed CAN segment without destabilising it. The TJA1055T is used in this role because it combines an enhanced fault-tolerant CAN transceiver with a standard 14-pin SOIC package, allowing several channels to be built on a dense instrument board. Its 125 kBd limit aligns with the low-speed body networks that are most often analysed, while the receive-data output can be captured by a microcontroller or FPGA for logging. Designers should still observe the manufacturer bus-line timing requirements and provide termination at the physical ends of the segment so that the analyser does not perturb the traffic it is measuring.
پێشنیارکراو
Vehicle Comfort and Lighting Subsystems
Lighting controllers, interior lighting hubs and comfort subsystems are distributed across the passenger car and communicate over low-speed CAN rather than a dedicated network. The TJA1055T is used as the physical-layer device in these controllers, providing the enhanced fault-tolerant CAN transceiver in the compact 14-pin SOIC package with a pin-to-pin relationship to the older TJA1054 and TJA1054A that lets existing lighting modules be updated in place. The fault-tolerant behaviour matters in this environment because harness faults and shorted bus lines are common causes of comfort-system malfunctions, and a node that survives them reduces warranty and diagnostic effort. Where the design later needs to carry larger payloads or move to CAN FD, the TJA1442AT/0Z is the natural step up in the same board family.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ TJA1055T — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | TJA1055T/3/C,518 | TJA1055T/CM,118 | TJA1055T/1J | TJA1054T/VM,518 | TJA1054AT |
|---|---|---|---|---|---|---|
| Package | SOIC-14 (SOP-14) surface mount | SOIC-14 (14-SO) - same footprint | SOIC-14 - same footprint | SOIC-14 - same footprint | SOIC-14 (SOP) - same footprint | SOIC-14 - same footprint |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Transceiver Type | CAN half transceiver with fault-tolerant bus lines | CAN half transceiver with fault-tolerant bus lines | CAN half transceiver with fault-tolerant bus lines | CAN half transceiver with fault-tolerant bus lines | CAN half transceiver, standard fault tolerance | CAN half transceiver, standard fault tolerance |
| Data Rate Support | up to 125 kBd | up to 125 kBd | up to 125 kBd | up to 125 kBd | up to 125 kBd | up to 125 kBd |
| Fault Tolerance Level | Enhanced fault-tolerant | Enhanced fault-tolerant | Enhanced fault-tolerant | Enhanced fault-tolerant | Standard (no TJA1055 enhancements) | Standard (no TJA1055 enhancements) |
| Pin Compatibility | Pin-to-pin compatible with TJA1054 and TJA1054A | Identical TJA1055 pinout | Identical TJA1055 pinout | Identical TJA1055 pinout | Predecessor, pin-compatible replacement path | Predecessor, pin-compatible replacement path |
| Number of Pins | 14 | 14 | 14 | 14 | 14 | 14 |
| Intended Network Segment | Low-speed in-car CAN (passenger cars) | Low-speed in-car CAN | Low-speed in-car CAN | Low-speed in-car CAN | Low-speed in-car CAN | Low-speed in-car CAN |
جیاکەرەوە سەرەکییەکان
- Enhanced fault-tolerant bus-line interface in a 14-pin SOIC footprint (بەراورد بەTJA1054T/VM,518)
- Documented drop-in upgrade path for existing passenger-car low-speed CAN designs (بەراورد بەTJA1054AT)
- Multiple order-code configurations available within one footprint (بەراورد بەTJA1055T/3/C,518)
تێبینییەکانی دیزاین
Place the TJA1055T close to the board connector that carries the CANH and CANL pairs. Route the two bus lines as a coupled, length-matched pair, keep the stubs from the transceiver to the connector as short as possible, and keep the pair away from switching nodes, inductors and any antenna routing. A short stub matters more here than in most designs because the bus-line driver output impedance and the cable termination interact directly with the segment reflections seen by the receiver.
Terminate the CAN segment at exactly two physical points, normally at the two ends of the bus, with the termination resistor value recommended in the manufacturer product specification. Adding termination in the middle of the segment or leaving it off in a two-node bench setup changes the bus impedance and can produce dominant-state errors that look like a faulty transceiver. Confirm also that the selected order-code suffix matches the supply and bus configuration of the target network before the layout is released.
Decouple the transceiver supply pin with a ceramic capacitor placed as close as possible to the pin and tie the ground pins directly to a solid ground plane, avoiding long ground traces that behave as an antenna. The bus transceiver is a switching device on the wiring, so supply noise on this node can appear directly on the bus. Estimated: with a 100 mV supply step and a 100 nF decoupling capacitor, the resulting supply transient is roughly limited by the loop inductance of the placement, so keep the capacitor and the ground return path within a few millimetres of the pins.
زانیاری پابەندبوون
Compliance declarations are published in the manufacturer product information for the TJA1055 family; confirm the RoHS, REACH and automotive qualification status for the specific order-code suffix on the NXP product page before release.