TJA1055T/C - Fault-Tolerant CAN Transceiver | NXP
MPN: TJA1055T/C ✓ چالاکTJA1055T/C گشتی
A CAN transceiver is the physical-layer component between a digital CAN controller and the wired CAN bus. It belongs to the hierarchy of CAN interface ICs, bus transceivers, interface semiconductors, and power-management-independent communication ICs. By converting logic-level TX and RX signals into bus-level signals, and returning bus state to the controller, it separates the network's physical signaling from the controller's data protocol and firmware.
The TJA1055 is designed for low-speed CAN networks and emphasizes fault tolerance. NXP identifies the TJA1055T as an enhanced fault-tolerant CAN transceiver, while the TJA1055 family is optimized for in-car low-speed communication. Its principal application is a passenger-car CAN network in which dependable bus operation and tolerance of fault conditions are more important than high-bandwidth communication.
The TJA1055 family is also pin-to-pin compatible with the NXP TJA1054 and TJA1054A according to the manufacturer datasheet. This compatibility supports PCB reuse when a design moves from an earlier transceiver generation to the enhanced TJA1055, although engineers should still review the associated CAN controller, bus termination, power-supply, and application requirements before approving a substitution.
Typical deployments include body and comfort systems, door modules, climate-control electronics, lighting controllers, seat controls, instrument-cluster peripherals, and other low-speed vehicle networks. The TJA1055T/C can also serve industrial or embedded CAN equipment when the system intentionally operates within the family's low-speed fault-tolerance design point. The protocol controller remains responsible for CAN frames, arbitration, error handling, and higher-layer communication.
A robust implementation requires correct transceiver decoupling, a suitable CAN controller interface, and the termination strategy appropriate to the complete bus. The two dominant bus conductors and the return path must be routed as a consistent network, while exposed connector wiring and automotive transients require careful protection planning. Review the manufacturer's application guidance and the completed PCB implementation before production release.
This page combines the manufacturer product information, the exact TJA1055T/C ordering information, package and speed data, pin-compatible family alternatives, and practical design guidance. It also distinguishes verified drop-in options from ordering variants that should not be treated as separate engineering alternatives.
جێگرەوەکانی جێگۆڕکێ بۆ TJA1055T/C — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
TJA1054T
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
TJA1054AT
✅ جێگرەوەی ڕاستەوخۆپەیوەندی بۆ نرخ
بینینی داتاشیت →TJA1055T/C تایبەتمەندییەکان
| Product Type | Enhanced fault-tolerant CAN transceiver |
| Maximum Intended Data Rate | 125 kBd |
| CAN Network Category | Low-speed Controller Area Network |
| Primary Application | In-car low-speed passenger-car communication |
| پاکێج | 14-pin SO |
| جۆری دامەزراندن | Surface mount |
| دۆخی چرخەی ژیان | Active |
| Transceiver Architecture | Half-duplex CAN transceiver |
| Fault-Tolerant Operation | Enhanced fault-tolerant CAN operation |
| Bus Interface | CANH and CANL wired-bus interface |
| Controller Interface | CAN TX and RX logic interface |
ڕێنمایی ڕێکخستنی پینی TJA1055T/C 14-pin so
ڕێکخستنی پین بۆ TJA1055T/C (پاکێجی 14-pin so). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ TJA1055T/C.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
TJA1055T/C گونجاوە بۆ 6 بەکارھێنانs: Passenger-Car Body Control Networks, Door and Seat Control Modules, Automotive Lighting Control, Climate and Comfort Electronics, Instrumentation Peripheral Modules, Low-Speed Embedded CAN Equipment.
Passenger-Car Body Control Networks
The TJA1055T/C is suitable for low-speed body and comfort networks that connect door, seat, lighting, climate, and convenience modules. Its fault-tolerant CAN design is aligned with passenger-car environments, while its 125 kBd intended operating point matches networks that exchange compact control and status messages rather than high-bandwidth multimedia data. In a body controller, the TJA1055T/C connects the controller's TX and RX signals to CANH and CANL while isolating the digital logic side from the physical bus. The principal design benefit is enhanced fault handling, but the implementation must still include correct decoupling, defined bus termination, protected routing, and connector transient considerations.
پێشنیارکراو
Door and Seat Control Modules
The TJA1055T/C fits distributed door-lock, window, seat, and convenience modules because it provides the physical CAN interface for a controller managing low-rate commands and diagnostics. At up to 125 kBd, the device addresses the low-speed in-car communication role identified by NXP rather than high-speed vehicle backbones. Place the transceiver beside the controller and route CANH and CANL as a matched pair toward the harness connection. A fault-tolerant interface helps the module manage communication disturbances, while proper reference-grounding, bus-stub control, and external transient protection remain essential when long harness branches connect the module to the vehicle network.
پێشنیارکراو
Automotive Lighting Control
The TJA1055T/C can serve as the CAN physical-layer interface in exterior or interior lighting controllers that exchange commands, status, and diagnostic information over a low-speed vehicle network. Its intended 125 kBd operation is appropriate for control traffic, and the enhanced fault-tolerant positioning supports automotive network use. The controller handles message content while the TJA1055T/C handles the electrical bus interface. To prevent intermittent faults, keep the bus pair away from switching nodes and motor drivers, provide local supply decoupling, use the manufacturer's recommended application network, and ensure that cable protection is coordinated with the vehicle harness's transient environment.
پێشنیارکراو
Climate and Comfort Electronics
The TJA1055T/C is appropriate for climate-control and comfort modules that distribute commands across a low-speed CAN network. Typical traffic includes set-point changes, operating-state reports, error indications, and diagnostic requests, all of which fit the low-speed communication role up to 125 kBd. The transceiver gives the local microcontroller a standardized physical interface to CANH and CANL without requiring the controller to manage analog bus signaling. Its enhanced fault-tolerant architecture is useful in vehicle installations, but reliable operation still depends on stable supply voltage, low-impedance grounding, controlled harness stubs, correct endpoint termination, and transient protection selected for the connector environment.
پێشنیارکراو
Instrumentation Peripheral Modules
The TJA1055T/C can provide the physical CAN interface for a remote instrumentation or status-display peripheral that exchanges compact information with a vehicle controller. The 125 kBd intended rate is suitable for messages such as switch states, sensor summaries, warning states, and control acknowledgements rather than continuous high-rate sensor streaming. The transceiver's fault-tolerant behavior is advantageous where the module is connected through vehicle harness wiring. Design the PCB with the transceiver near the harness interface, maintain a continuous CANH/CANL route, follow the manufacturer grounding arrangement, and use protection components that do not distort normal bus operation while limiting external fault energy.
پێشنیارکراو
Low-Speed Embedded CAN Equipment
The TJA1055T/C may be used in embedded equipment where a low-speed, fault-tolerant CAN network is intentionally preferred, such as industrial auxiliary control networks with conservative communication rates. The device is optimized for in-car communication up to 125 kBd, so its suitability in an industrial design depends on matching environmental, electrical, and qualification requirements to the installation. It separates the controller's TX and RX interface from the CANH and CANL bus while allowing the network to remain operational during specified fault conditions. Validate grounding, bus length, termination, fault-mode behavior, and external protection rather than assuming passenger-car suitability guarantees every industrial environment.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ TJA1055T/C — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | TJA1054T | TJA1054AT |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 14-pin SO | 14-pin SO - pin-to-pin compatible | 14-pin SO - pin-to-pin compatible |
| Product Type | Enhanced fault-tolerant CAN transceiver | Fault-tolerant CAN transceiver | Enhanced fault-tolerant CAN transceiver |
| Primary Network Role | Low-speed in-car CAN communication | Low-speed CAN communication | Low-speed CAN communication |
| Bus Interface | CANH and CANL | CANH and CANL | CANH and CANL |
| Controller Interface | TX and RX | TX and RX | TX and RX |
| Fault-Tolerant Positioning | Enhanced fault-tolerant TJA1055 family | Earlier TJA1054 generation | Earlier TJA1054A generation |
| Mounting Type | Surface mount | Surface mount | Surface mount |
جیاکەرەوە سەرەکییەکان
- Enhanced fault-tolerant positioning within an established pin-compatible family (بەراورد بەTJA1054T)
- Direct PCB reuse from TJA1054AT without changing the footprint (بەراورد بەTJA1054AT)
- Low-speed vehicle-network optimization with a 125 kBd intended operating point (بەراورد بەTJA1054T)
تێبینییەکانی دیزاین
Follow the NXP TJA1055 recommended application layout when placing the transceiver, supply decoupling, CANH, CANL, and ground connections. Keep the CAN bus pair continuous and route it away from switching power nodes and unrelated high-current paths. Connect the transceiver ground using the datasheet's reference-ground arrangement rather than relying on a nearby general-purpose ground pour. Verify the final connector protection network against the vehicle transient environment.
Do not treat the TJA1055T/C ordering suffix as a separate electrical design. Use the TJA1055 family datasheet together with the exact TJA1055T/C ordering information, and verify the selected package and tape-and-reel form before release. Pin-to-pin compatibility does not by itself prove that every TJA1054 or TJA1054A operating limit, timing condition, and fault-mode requirement is identical, so complete a design review before substitution.
Provide the transceiver with the supply voltage and decoupling specified by the manufacturer datasheet, and keep the supply-return path short and low impedance. Fault-tolerant behavior does not remove the need for stable local power or correct reference grounding. During power sequencing, reset, or connector fault testing, verify that the CAN controller and transceiver remain in valid states and that external protection components do not continuously load the bus.
Treat CANH and CANL as one controlled bus pair throughout the PCB and harness interface. Match their geometry, minimize unnecessary stubs, and apply termination according to the complete network topology rather than adding termination solely at the transceiver. Use the manufacturer's recommended protection and filtering arrangement so that normal-mode bus behavior is preserved while connector transients are constrained.
زانیاری پابەندبوون
The manufacturer identifies TJA1055T as active and optimized for low-speed in-car communication. Specific environmental and regulatory status values require confirmation from the current NXP product documentation or declaration.