NXP Semiconductors

TJA1145AT/0Z - 5 Mbit/s CAN FD Transceiver | NXP

MPN: TJA1145AT/0Z ✓ چالاک
MOQ: 1 |

TJA1145AT/0Z گشتی

NXP Semiconductors TJA1145AT/0Z is an automotive high-speed CAN transceiver for partial networking, providing the interface between a CAN protocol controller and a two-wire CAN bus. It supports CAN and CAN FD communication at data rates up to 5 Mbit/s and combines differential transmit and receive capabilities with selective wake-up functionality. The device is intended for in-vehicle networks where low standby consumption, bus fault tolerance, and partial-networking capability can reduce the energy required by modules that do not communicate continuously.

A CAN transceiver is an interface IC within the broader network-communications semiconductor hierarchy. It converts logic-level signals from a CAN controller into differential bus levels and converts differential bus activity back into controller-compatible receive signals. The TJA1145A family adds partial networking, allowing a node to wake selectively when recognized traffic appears on the bus rather than remaining fully active for every unrelated frame.

The key features of the TJA1145AT/0Z include support for CAN FD communication up to 5 Mbit/s, differential CAN bus transmission and reception, selective wake-up, and very low power consumption in Standby and Sleep modes. NXP identifies the device as suitable for automotive applications. The device is supplied under the automotive-oriented TJA1145A family designation and is available in a compact surface-mount package, although the exact package dimensions and pin assignments must be confirmed in the manufacturer datasheet before PCB release.

The transceiver provides a physical-layer interface for systems that already contain a CAN protocol controller. It does not replace the controller, arbitration logic, or application software. Designers should therefore verify that the selected CAN controller supports the required classical CAN or CAN FD data rates and that its logic levels, supply voltage, and transceiver-control signals match the TJA1145AT/0Z interface.

Typical uses include body-control modules, gateway controllers, telematics units, battery-management systems, and other ECUs connected to partially dormant vehicle networks. Partial networking is especially useful where many nodes share a CAN backbone but only a subset must communicate at a given time, allowing unneeded modules to remain in a low-power state.

PCB implementation requires correct termination, common-mode behavior, and decoupling. The CANH and CANL bus connections should follow the layout guidance in the manufacturer datasheet, while the device supply pins require local high-frequency bypass capacitors. Bus stubs should be minimized, and the 120-ohm termination network belongs at the physical ends of the bus rather than at every node.

This page organizes the TJA1145AT/0Z technical profile, verified manufacturer and distributor resources, supported applications, and design guidance. It also distinguishes the exact ordered part number from related TJA1145A variants so engineers can assess protocol behavior, package, and qualification requirements before substituting an alternative.

جێگرەوەکانی جێگۆڕکێ بۆ TJA1145AT/0Z — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.

جۆرەکان لەم زنجیرەیەدا

مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TJA1145AT/0Z (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Product Type, Package, Data Rate, Function, Operating Modes.

NXP Semiconductors
Product Type: System Basis Chip (SBC Gen2)
NXP Semiconductors
Package: 14-SOIC (SO-14)
Function: CAN / CAN FD Transceiver
NXP Semiconductors
Package: 14-HVSON (3x4.5 mm) with exposed pad
Data Rate: 5 Mbps (CAN FD capable)
Function: High-speed CAN transceiver with partial networking
NXP Semiconductors
Product Type: High-speed CAN transceiver for partial networking
Package: 14-HVSON (3x4.5 mm) with exposed pad
Data Rate: 5 Mbps

TJA1145AT/FD/0Z

✅ جێگرەوەی ڕاستەوخۆ
📦 14-SO
Uses the same 14-SO package class but adds the FD-passive partial-networking implementation; detailed pin and mode compatibility must be confirmed before substitution

📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)

TJA1145AT/0Z تایبەتمەندییەکان

Product Type High-speed CAN and CAN FD transceiver
Supported Protocol CAN and CAN FD
Maximum Data Rate 5 Mbit/s
Bus Configuration Two-wire differential CAN bus
Automotive Data Rate Up to 5 Mbit/s
Partial Networking Support Yes
Selective Wake-Up Supported
Transmit Capability Differential
Receive Capability Differential
Power Modes Off, Standby and Sleep
Standby and Sleep Power Consumption Very low power consumption
ISO 11898-2:2016 Compliance Compliant for ISO 11898-2:2016 CAN Partial Networking
مەودای پلەی گەرمیی کارکردن -40 C to +150 C
جۆری دامەزراندن Surface mount

ڕێنمایی ڕێکخستنی پینی TJA1145AT/0Z standard

ڕێکخستنی پین بۆ TJA1145AT/0Z (پاکێجی standard). ژمارەدانی پین، فەنکشنەکان و نەخشەکانی پەیوەندی لە داتاشیتی بەرھەمھێنەردا پێناسە کراون. سەرنجی بدە بۆ شوێنپێی ورد و ڕێنمایییەکانی لەحیمکردن.

نەخشەی پینئاوتی پاکێجی standard بۆ TJA1145AT/0Z

هیچ داتای وردی پینئاوت بەردەست نییە بۆ TJA1145AT/0Z.

سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.

بەکارهێنانە باوەکان

TJA1145AT/0Z گونجاوە بۆ 6 بەکارھێنانs: Automotive CAN FD Gateway, Body Control Module CAN Interface, Battery Management System CAN Interface, Telematics and Connectivity ECU, Partial-Networking Diagnostic Node, Industrial CAN FD Control Module.

🚗

Automotive CAN FD Gateway

The TJA1145AT/0Z fits a gateway interface that must communicate on a two-wire vehicle CAN network at rates up to 5 Mbit/s. It provides the physical-layer differential transmit and receive functions required by a CAN protocol controller, allowing gateway software to exchange conventional CAN or CAN FD traffic with other vehicle domains. Selective wake-up is valuable when the gateway must remain asleep during idle intervals but activate for recognized bus activity. The implementation still needs correct CAN termination, a compatible controller, local supply decoupling, and an automotive-rated board layout.

🚗

Body Control Module CAN Interface

The TJA1145AT/0Z is appropriate for a body control module that participates in a partially networked vehicle backbone while managing several electrical subsystems. Its CAN and CAN FD support up to 5 Mbit/s provides a flexible physical layer for controller traffic, while selective wake-up can avoid continuous wakefulness when the module has no relevant messages. Engineers should pair the transceiver with the module's CAN controller, design the CANH and CANL routes as a controlled differential pair, and verify supply thresholds and mode-transition timing in the TJA1145A datasheet.

⚡

Battery Management System CAN Interface

A battery-management system can use the TJA1145AT/0Z to connect its CAN controller to a vehicle-wide CAN network supporting data rates up to 5 Mbit/s. The differential bus interface suits the noisy electrical environment typical of automotive power systems, while low Standby and Sleep consumption can help avoid unnecessary load when partial networking determines that the module has no relevant traffic. Bus fault handling, ISO 11898-2:2016 partial-networking behavior, and the device's exact wake criteria must be reviewed before final system configuration.

🌐

Telematics and Connectivity ECU

The TJA1145AT/0Z suits a telematics ECU that exchanges diagnostic, network-management, or vehicle-status messages over a partially networked CAN bus. Its support for communication up to 5 Mbit/s permits use with CAN FD-capable controllers, and selective wake-up lets the ECU reduce activity when selected messages are absent. For this application, the key checks are controller protocol compatibility, wake-up acceptance criteria, bus termination placement, and separation of transceiver bus traces from sensitive radio and signal-processing circuitry.

🖥️

Partial-Networking Diagnostic Node

The TJA1145AT/0Z can support a diagnostic node that should participate only when particular CAN traffic is present. Its selective wake-up function is central to this use because it reduces the need to keep every network node active throughout the vehicle's duty cycle. NXP identifies ISO 11898-2:2016-compliant CAN Partial Networking as a supported capability. Designers should define the wake-up filter and message behavior in the CAN controller or network configuration, then confirm the operating-mode transitions and bus behavior against the manufacturer documentation.

🏭

Industrial CAN FD Control Module

The TJA1145AT/0Z can be evaluated for industrial CAN FD control modules requiring a 5 Mbit/s differential physical layer. It is described by NXP as an automotive CAN transceiver, so industrial adoption requires review of its environmental qualification, protection needs, and supply limitations. The differential CANH and CANL interface, low-power sleep behavior, and partial-networking capability can benefit compact automation equipment. Confirm electromagnetic robustness, fault tolerance, temperature requirements, and any automotive-specific qualification assumptions before using it outside a vehicle.

What is the NXP TJA1145AT/0Z?
The NXP TJA1145AT/0Z is a high-speed CAN and CAN FD transceiver for partial networking in automotive systems. According to the NXP TJA1145A datasheet, it connects a CAN protocol controller to a two-wire differential CAN bus and supports communication at data rates up to 5 Mbit/s. Its selective wake-up capability lets a sleeping node recognize qualifying bus activity, reducing unnecessary activity on partially networked vehicle systems.
What are the key specifications of TJA1145AT/0Z that engineers should know?
The TJA1145AT/0Z is a surface-mount CAN and CAN FD physical-layer transceiver supporting operation up to 5 Mbit/s. Its main engineering characteristics are differential transmission and reception, two-wire bus connectivity, selective wake-up, partial networking, and very low power consumption in Standby and Sleep modes. NXP also identifies ISO 11898-2:2016 compliance for CAN Partial Networking. The exact supply-voltage limits, pinout, and package dimensions should be taken from the manufacturer datasheet.
Is TJA1145AT/0Z compatible with CAN FD?
Yes, the TJA1145AT/0Z supports CAN FD communication at data rates up to 5 Mbit/s. According to NXP's TJA1145A product information, the device provides differential transmit and receive capabilities for in-vehicle networks. CAN FD protocol support does not remove the need to verify controller timing, arbitration, termination, and bus topology; those aspects remain part of the complete CAN FD network design.
Where to download the TJA1145AT/0Z datasheet PDF?
Download the TJA1145A datasheet from NXP at https://www.nxp.com/docs/en/data-sheet/TJA1145A.pdf. The document is the manufacturer reference for electrical limits, operating modes, pin descriptions, application information, and recommended layouts. Use the NXP TJA1145AT product page at https://www.nxp.com/part/TJA1145AT for lifecycle status, product links, and ordering information associated with the device family.
Where can I find the TJA1145AT/0Z pinout?
The TJA1145AT/0Z pinout is shown in the pin-description and package-dimension sections of the NXP TJA1145A datasheet. Before assigning PCB tracks, use the pin-description table for the exact TJA1145AT ordering code. Confirm package dimensions, exposed-pad or lead requirements, and pad layout against the latest manufacturer drawing rather than relying on a generic CAN-transceiver footprint.
What does selective wake-up do in the TJA1145AT/0Z?
Selective wake-up allows the TJA1145AT/0Z to recognize designated CAN bus activity and transition from Sleep into an active operating state. According to the NXP TJA1145A datasheet, this supports ISO 11898-2:2016 CAN Partial Networking. The feature is useful in vehicle networks where many ECUs share one backbone, because nodes unrelated to a requested message can remain in a low-power state.
What is the difference between TJA1145AT/0Z and TJA1145AT/FD/0Z?
TJA1145AT/0Z and TJA1145AT/FD/0Z are related 14-pin CAN transceiver order codes, but the FD order code is specifically associated with the dedicated FD-passive partial-networking implementation. NXP community documentation confirms that specification differences exist even though some applications may use both devices successfully. Verify the protocol mode, wake-up behavior, and exact datasheet ordering table rather than treating the suffix as interchangeable.
Can TJA1145AT/FD/0Z replace TJA1145AT/0Z on the same PCB?
TJA1145AT/FD/0Z uses the same 14-SO package class identified for the related device, but a matching package alone does not prove that every operating mode is interchangeable. NXP community discussions identify FD-passive behavior differences between the FD and non-FD naming variants. Before using it as a drop-in replacement, compare the pin descriptions, wake-up implementation, protocol behavior, and operating-mode requirements in the manufacturer datasheet.
What is the best drop-in replacement for TJA1145AT/0Z?
The closest documented candidate is NXP's TJA1145AT/FD/0Z because it appears in the same 14-SO package family, but the FD variant has a dedicated FD-passive partial-networking implementation and may not preserve the original behavior in every mode. No complete cross-brand set of verified, pin-compatible alternatives was established. Use the Request a Quote form on this page to discuss the exact replacement requirement, and validate any substitution against the latest NXP datasheet.
When should I choose TJA1145AT/0Z over another CAN transceiver?
Choose the TJA1145AT/0Z when the design needs a 5 Mbit/s automotive CAN and CAN FD physical-layer interface with selective wake-up and partial networking. Select an FD-specific variant only when its FD-passive behavior is explicitly required. Other CAN transceivers may be preferable for lower-speed classical CAN-only networks, different supply ranges, non-automotive qualification, or alternative low-power architectures. Package compatibility alone should not determine the choice.
Is the TJA1145AT/0Z suitable for an automotive gateway?
The TJA1145AT/0Z is suitable for many automotive gateway interfaces because it supports CAN and CAN FD up to 5 Mbit/s and is designed for partial networking in vehicle networks. Its selective wake-up can reduce power use when the gateway must respond only to selected activity. Final suitability still depends on the gateway's supply architecture, CAN controller, bus termination, protection strategy, environmental qualification, and communication timing.
What is the operating temperature range of TJA1145AT/0Z?
The listed operating temperature range for TJA1145AT/0Z is -40 C to +150 C. This range is appropriate for many harsh automotive environments, but engineers should also check the exact ordering code, power mode, supply conditions, and package limits in the NXP TJA1145A datasheet. Junction temperature and transient conditions must remain within the device's specified operating limits.
Where can I buy TJA1145AT/0Z online?
Use the Request a Quote form on this page to request the current price, stock status, minimum order quantity, and lead time for TJA1145AT/0Z. The form allows the requested exact suffix to be identified without ambiguity from related TJA1145AT order codes. Current commercial terms should be confirmed at request time because availability and lead time can change with inventory and production conditions.
What is the price of TJA1145AT/0Z?
Use the Request a Quote form on this page for the current commercial terms of the exact TJA1145AT/0Z order code. The form is the appropriate channel because market pricing and stock can vary by quantity, date, and order configuration. When requesting a quote, identify the package or reel quantity required and any need for automotive traceability or date-code control.
What is the lead time and stock status for TJA1145AT/0Z?
Request the current lead time and stock status through the Request a Quote form on this page. Provide the required quantity, date-code preference, packaging format, and destination or delivery schedule so procurement can confirm the exact order code. NXP's product page identifies TJA1145AT as active, but live inventory and individual manufacturing lead time should always be confirmed through a current quotation.
Is TJA1145AT/0Z RoHS compliant and suitable for automotive production?
The TJA1145AT/0Z is an automotive-oriented NXP transceiver, but its RoHS, REACH, halogen-free, and conflict-minerals declarations must be confirmed for the exact ordering code in NXP's current product documentation. Do not infer every certification statement solely from the family name. Request the applicable material or environmental compliance records during qualification and supplier review.

داتای سەرچاوەی ئەندازیاری بۆ TJA1145AT/0Z — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.

ڕێنمایی هەڵبژاردن

Choose TJA1145AT/0Z for an automotive or industrial evaluation requiring a CAN and CAN FD physical layer up to 5 Mbit/s, selective wake-up, and partial networking. It is especially appropriate when the system can benefit from keeping inactive vehicle nodes in Sleep or Standby modes. TJA1145AT/FD/0Z is the closest documented same-package candidate, but its FD-passive partial-networking behavior may change wake and mode semantics, so substitution requires functional verification rather than footprint matching alone. No verified cross-brand drop-in alternatives were established, and parts with different logic interfaces, supply ranges, qualification targets, or wake architectures should not be treated as direct replacements. For a new design, confirm the exact package, pinout, electrical limits, CAN controller compatibility, bus protection requirements, and compliance records from the latest NXP documentation before releasing the PCB.

بەراوردکردن لەگەڵ جێگرەوەکان

پارامەتر ئەم بەرهەمە TJA1145AT/FD/0Z
Brand NXP Semiconductors NXP Semiconductors
Product Type CAN and CAN FD transceiver CAN and CAN FD transceiver
Maximum Data Rate 5 Mbit/s 5 Mbit/s
Partial Networking Supported Supported with dedicated FD-passive implementation
Selective Wake-Up Supported Supported
Power Consumption Very low in Standby and Sleep modes Very low in Standby and Sleep modes
Bus Interface Two-wire differential CAN bus Two-wire differential CAN bus

جیاکەرەوە سەرەکییەکان

  • Supports both CAN and CAN FD (بەراورد بەTJA1145AT/FD/0Z)
  • Designed for selective partial networking (بەراورد بەTJA1145AT/FD/0Z)
  • Five-megabit CAN FD performance (بەراورد بەTJA1145AT/FD/0Z)

تێبینییەکانی دیزاین

Route CANH and CANL as a tightly coupled differential pair with continuous return-path geometry, symmetrical spacing, and minimal vias. Place the transceiver close to the bus connector or bus interface area and keep the connector-to-transceiver branch short. Follow the exact pad geometry and layout recommendations in the NXP TJA1145A datasheet rather than constructing a footprint from the generic package name.

Place the required supply bypass capacitors immediately beside the device power and ground pins, with the shortest possible ground return. Verify startup, sleep, standby, and wake-up supply thresholds in the manufacturer datasheet before setting the vehicle supply network. Because the TJA1145AT/0Z supports low-power modes, supply noise, thresholds, and mode transitions should be validated together rather than evaluated only at the nominal operating condition.

Do not treat TJA1145AT/0Z and TJA1145AT/FD/0Z as automatically identical because both use a 14-SO package. The FD ordering code is associated with a dedicated FD-passive partial-networking implementation. Compare pin descriptions, wake criteria, controller behavior, and operating-mode state diagrams in the NXP datasheet, and perform bus-level regression testing before changing an approved production design.

Install 120-ohm termination only at the two physical endpoints of the CAN bus. Avoid placing termination across every transceiver, and keep stub branches short because excessive stub length can alter differential impedance and signal integrity. Validate both command and bus termination with the vehicle network's complete topology, including cable length, node count, and any diagnostic or split-bus arrangements.

زانیاری پابەندبوون

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
بێ قوڕقوشم
Unknown
بێ ھالۆجین
Unknown
کانزا ناکۆکەکان
Unknown

The product is an automotive-oriented CAN transceiver, but exact compliance declarations for the TJA1145AT/0Z ordering code were not established. ISO 11898-2:2016 CAN Partial Networking compliance is identified by NXP.

گەڕانە پەیوەندیدارەکان

nxp tja1145at TJA1145AT/0Z datasheet TJA1145AT/0Z datasheet pdf TJA1145AT/0Z pinout TJA1145AT/0Z package TJA1145AT/0Z equivalent TJA1145AT/0Z replacement TJA1145AT/0Z cross reference TJA1145AT/0Z vs TJA1145AT/FD/0Z TJA1145AT/0Z CAN FD transceiver TJA1145AT/0Z 5 Mbit/s TJA1145AT/0Z automotive CAN TJA1145AT/0Z price TJA1145AT/0Z stock

پێکهاتە و زاراوە پەیوەندیدارەکان

NXP Semiconductors TJA1145AT/0Z TJA1145AT TJA1145A TJA1145AT/FD/0Z TJA1145T/FDJ TJA1145ATK/0Z TJA1442AT/0Z CAN transceiver CAN FD partial networking selective wake-up automotive network two-wire CAN bus differential transmit differential receive ISO 11898-2:2016 Standby mode Sleep mode Off mode 5 Mbit/s CANH CANL semiconductor
داواکاری نرخی خێرا RFQ
وردەکارییەکانی تەواو پڕ بکەرەوە — تیمی فرۆشتنی ئێمە لە ماوەی 24 کاتژمێردا وەڵام دەداتەوە
ژمارەی پارچە بەرهەمهێنەر پاکەت QTY نرخی ئامانج کۆی گشتی
✓
نرخەکە نێردرا!

لە ماوەی ٢٤ کاتژمێردا وەڵامی ئیمەیڵەکەت دەدەینەوە

1
داواکاری نرخ پێشکەشکرا
2
نرخپێدان وەرگیرا
3
داواکاری دانرا
4
پارەدان
5
نێردرا
6
گەیەنراوە
بینینی وردەکاریی داواکاری نرخ