TS555IN - 2.7 MHz Low-Power CMOS Timer | STMicroelectronics
MPN: TS555IN ✗ کۆتایی ژیانTS555IN گشتی
A programmable timer is an integrated circuit that combines timing elements, comparators, a flip-flop, and a high-current output stage into one device. The TS555IN belongs to the 555 timer family, which sits within clock and timing ICs and can operate as a monostable one-shot or an astable free-running oscillator. This integration removes the need for discrete comparator, flip-flop, and discharge-transistor networks in common delay and pulse-generation circuits.
The principal advantages are low supply consumption, high operating frequency, and reduced supply-current spikes during output transitions. The cited manufacturer product page reports typical TS555 supply current of 110 uA at a 5 V supply, while a distributor specification listing reports 65 uA under its specified test conditions. The maximum astable frequency of 2.7 MHz is substantially higher than the 0.1 MHz maximum commonly associated with the bipolar NE555 in the supplied comparison data.
The TS555IN supports both one-shot and free-running operation. In monostable mode, its output changes state for a controlled interval after an external trigger. In astable mode, external resistors and a capacitor establish repeated output oscillations. The 2 V to 16 V operating range permits use from low-voltage battery-powered equipment through higher-voltage industrial control circuits, subject to the component's detailed absolute maximum ratings.
Typical uses include pulse generation, delayed switching, debounce and missing-pulse circuits, simple oscillators, LED flashers, industrial timing modules, and control-signal generation. Its CMOS implementation is particularly useful where standby supply current matters, while its 2.7 MHz maximum frequency supports higher-rate timing than the bipolar reference timer.
Designers should preserve the standard 555 interface when making PCB substitutions and should account for the TS555's low-voltage limitations, timing tolerances, and output-drive behavior. Supply bypassing and timing-component placement should follow the manufacturer datasheet, especially in astable circuits operating near the 2.7 MHz upper frequency limit.
This product page consolidates manufacturer specifications, distributor availability information, verified cross-reference results, and practical selection guidance. It also distinguishes true same-package replacements from functionally similar timer families that may require different pinouts, voltage tolerances, or application-level qualification.
جێگرەوەکانی جێگۆڕکێ بۆ TS555IN — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ TS555IN (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Package, Mounting Type, Timer Type, Supply Voltage Range, Operating Temperature Range.
TS555ID
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →TS555CN
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →TS555CD
✅ جێگرەوەی ڕاستەوخۆ ⚠️ تایبەتمەندییەکان پشتڕاست نەکراونەتەوەپەیوەندی بۆ نرخ
بینینی داتاشیت →TS555IN تایبەتمەندییەکان
| Timer Type | 555 Type, Timer/Oscillator (Single) IC |
| Technology | CMOS |
| Maximum Astable Frequency | 2.7 MHz |
| Supply Voltage Range | 2 V to 16 V |
| ئێستای دابینکردن | 65 uA |
| Typical Supply Current at 5 V | 110 uA |
| Datasheet Typical Supply Current at 5 V | 100 uA |
| مەودای پلەی گەرمیی کارکردن | -40 C to +125 C |
| پاکێج | 8-DIP (0.300 inch, 7.62 mm) |
| جۆری دامەزراندن | Through Hole |
| ژمارەی پین | 8 pins |
| Supported Timer Mode | Monostable and Astable |
| Functional Compatibility | Pin-to-pin and functionally compatible with bipolar NE555 |
| Output Current Capability | High output current capability; exact value not supplied |
| Supply Current Spike Behavior | Reduced during output transitions |
| Absolute Maximum Supply Voltage | Up to +18 V |
| Manufacturer Product Status | Obsolete |
ڕێکخستنی پینی TS555IN
| پین 1 | GND — Ground reference |
| پین 2 | TRIG — Trigger input |
| پین 3 | OUT — Timer output |
| پین 4 | RESET — Reset input |
| پین 5 | CV — Control voltage input |
| پین 6 | THR — Threshold input |
| پین 7 | DIS — Discharge output |
| پین 8 | VCC — Power supply |
بەکارهێنانە باوەکان
TS555IN گونجاوە بۆ 6 بەکارھێنانs: Battery-Powered Pulse Generator, High-Frequency Astable Oscillator, Industrial Delayed-Trigger Circuit, LED Flasher and Indicator Driver, Debounce and Missing-Pulse Logic, Low-Power Test and Measurement Trigger.
Battery-Powered Pulse Generator
The TS555IN fits battery-powered pulse generation because the verified data reports typical supply current of 100-110 uA at 5 V, compared with 3 mA for the bipolar NE555. Its CMOS architecture preserves the familiar monostable timing function while reducing standby demand in duty-cycled control, wake-up, and indicator circuits. The 2 V to 16 V operating range allows the timer to operate across several low-voltage rails, although timing accuracy must be checked as the supply falls. At the stated 5 V condition, the device can operate at 100-110 uA, while the maximum astable frequency of 2.7 MHz provides additional timing margin for compact pulse-frequency designs.
پێشنیارکراو
High-Frequency Astable Oscillator
The TS555IN is appropriate for a compact astable oscillator requiring a maximum frequency of 2.7 MHz, which is materially above the 0.1 MHz maximum cited for the bipolar NE555. External resistors and a timing capacitor set the repetition rate, while the integrated discharge and control functions reduce discrete component count. The CMOS implementation's 100-110 uA typical supply current at 5 V also limits continuous power demand in compact timing modules. Designers operating near the upper frequency limit should verify resistor impedance, capacitor selection, output loading, and supply decoupling using the manufacturer datasheet.
پێشنیارکراو
Industrial Delayed-Trigger Circuit
The TS555IN can implement a delayed trigger or one-shot in industrial control modules because it retains the standard 555 monostable interface and supports a 2 V to 16 V supply range. An external trigger can initiate a defined output pulse whose duration is set by timing components, allowing relay-command, counter, or acknowledgement logic to use a compact circuit. The verified operating range extends to 125 C for the listed TS555IN variant, supporting wider environmental conditions when the complete assembly and selected suffix are qualified. Low CMOS supply consumption also helps when the timing circuit remains connected to a shared control supply.
پێشنیارکراو
LED Flasher and Indicator Driver
The TS555IN is well suited to LED flashing and indication circuits because its astable mode repeatedly switches its output while the low 65 uA supply-current figure listed by one distributor reduces the effect of continuous timer overhead. The output stage can drive an indicator through an appropriate current-limiting path, and the 2 V to 16 V operating range supports both low-voltage novelty circuits and higher-voltage control panels. Compared with a bipolar NE555, the CMOS timer reduces supply consumption substantially at 5 V. LED current, duty cycle, and resistor sizing remain application-specific and should be validated against the absolute maximum ratings.
پێشنیارکراو
Debounce and Missing-Pulse Logic
The TS555IN can implement debounce or missing-pulse detection where a compact, independent timer must observe irregular mechanical or sensor transitions. Monostable operation can extend a short event into a usable pulse, while astable and gating arrangements can detect absent expected transitions. The device's low CMOS supply consumption of approximately 100-110 uA at 5 V makes it useful in continuously powered monitoring assemblies. The 2.7 MHz maximum frequency provides ample timing range for low-frequency industrial inputs. Threshold voltages, trigger timing, and noise immunity must be evaluated against the actual signal environment.
پێشنیارکراو
Low-Power Test and Measurement Trigger
The TS555IN is useful in low-power test fixtures that need a local pulse source, trigger delay, or repetitive stimulus without a complex timing controller. Its 2 V to 16 V supply range allows operation from common laboratory and embedded rails, while the 2.7 MHz maximum astable frequency supports faster test repetition than the bipolar NE555 reference. The low typical supply current also limits interference with adjacent sensitive circuitry during idle intervals. For accurate measurements, account for timing-component tolerance, output rise and fall behavior, and supply variation across the complete 2 V to 16 V operating range.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ TS555IN — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | TS555ID | TS555CN | TS555CD |
|---|---|---|---|---|
| Package | 8-DIP (0.300 inch, 7.62 mm) | 8-DIP (0.300 inch, 7.62 mm) | 8-DIP (0.300 inch, 7.62 mm) | 8-DIP (0.300 inch, 7.62 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Technology | Single CMOS timer | Single CMOS timer | Single CMOS timer | Single CMOS timer |
| Timer Modes | Monostable and Astable | Monostable and Astable | Monostable and Astable | Monostable and Astable |
جیاکەرەوە سەرەکییەکان
- Lower typical supply consumption than a bipolar NE555 (بەراورد بەBipolar NE555)
- Higher maximum astable operating frequency (بەراورد بەBipolar NE555)
- Lower-voltage operation (بەراورد بەBipolar NE555)
تێبینییەکانی دیزاین
Verify the supply rail against the 2 V to 16 V operating range and keep the absolute maximum limit of up to +18 V in perspective. The listed supply current varies by source and test condition, with values of 65 uA, 100 uA, and 110 uA appearing in the verified data. Use the 110 uA figure from the STMicroelectronics family page for preliminary battery-budget calculations and confirm the exact value for the production suffix and operating voltage on the datasheet.
Place the supply bypass capacitor and timing components close to their associated IC pins to minimize switching noise and timing-distortion effects. The TS555's CMOS architecture can support a 2.7 MHz maximum astable frequency, so long timing-node traces may become significant at high repetition rates. Use a ground reference plane, keep the output return path compact, and follow the manufacturer application diagram for control-voltage bypass and discharge-loop layout.
Do not treat a family-compatible 555 as an unconditional substitute without checking temperature grade, lifecycle state, supply range, timing limits, output current, and absolute maximum ratings. The TS555IN is reported as obsolete, while the alternative suffixes may represent different commercial or industrial temperature grades. Confirm that the selected replacement remains in the same 8-DIP footprint and verify its manufacturer datasheet before updating a released PCB.
زانیاری پابەندبوون
The supplied verified data does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status for TS555IN. The operating temperature range and obsolete product status must not be treated as substitutes for formal compliance information.