Integrierte Schaltungen

PIC16F1508-I/SS

PIC16F1508-I/SS - 20MHz 8-Bit MCU 7KB Flash XLP | Microchip

The Microchip Technology PIC16F1508-I/SS is an 8-bit PIC microcontroller featuring a 20 MHz enhanced mid-range core, 7 KB Flash program memory, 256 bytes RAM, and 18 I/O pins housed in a 20-pin SSOP package. It integrates a 10-bit ADC, configurable logic cells, and Microchip's eXtreme Low Power (XLP) technology for battery-friendly operation. The device operates from 2.3 V to 5.5 V supply voltage and supports industrial temperature range of -40C to +85C. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. Within the broader semiconductor hierarchy, an MCU sits under microcontrollers, which themselves are a sub-category of integrated circuits and embedded processors. The 8-bit class — to which the PIC16F1508 belongs — targets cost-sensitive, deterministic, low-power embedded applications where a 32-bit core would be over-specified. XLP technology is Microchip's branding for sub-uA sleep currents suitable for battery-powered IoT endpoints. Key differentiating features include 49 instruction enhanced mid-range core, 16-level hardware stack with overflow/underflow reset, 4 channel 10-bit ADC, and Core Independent Peripherals (CIPs) that offload tasks like waveform generation and signal conditioning from the CPU. The 7 KB self-programmable Flash supports in-application programming via the ICSP interface. Two File Select Registers (FSRs) and direct/indirect/relative addressing modes simplify pointer-heavy C and assembly code. The PIC16F1508 implements a Harvard architecture with separate program and data buses, predictable instruction timing (most instructions complete in one or two clock cycles), and deterministic interrupt latency that simplifies real-time firmware design. CIPs such as CLC, NCO, and PWM operate without CPU intervention, reducing firmware complexity for motor control, lighting, and sensor signal-chain tasks. Typical applications include consumer electronics human-interface controls, low-power IoT sensor nodes, LED lighting drivers using the NCO and PWM peripherals, small appliance control, and battery-powered instrumentation. The XLP sleep currents below 1 uA make it well-suited to energy-harvesting or coin-cell designs. When designing with this MCU, prioritize low-power modes (sleep/doze) for battery life, place decoupling capacitors within 5 mm of each VDD pin, and use the ICSP header for both debug and in-circuit programming. Program Flash carefully to respect the 10K erase/write endurance specification when storing user-mutable parameters. This page synthesizes distributor pricing from DigiKey and Mouser, drop-in same-package alternatives, and practical design notes drawn from Microchip's PIC16(L)F1508/9 datasheet that are not aggregated elsewhere.

Angebot Kontakt

PIC16F1508T-I/ML

PIC16F1508T-I/ML - 8-bit MCU, 7KB Flash, 20MHz, 20-QFN | Microchip

The Microchip PIC16F1508T-I/ML is an 8-bit PIC16 microcontroller from the PIC® XLP™ 16F family, featuring 7KB (4K x 14) of Flash program memory, 256 bytes of RAM, and an 18 I/O pin count. It operates at up to 20MHz clock speed from a 2.3V to 5.5V supply range in a 20-pin QFN (4x4 mm) package with exposed pad. The device integrates a 10-bit ADC, Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and Numerically Controlled Oscillator (NCO), targeting low-power and mixed-signal embedded designs. An 8-bit microcontroller (MCU) is a programmable computing-on-a-chip built around an 8-bit data path, on-chip Flash for code storage, RAM for working data, and a rich set of peripherals. Within the broader taxonomy, the PIC16F1508 sits at: PIC16 family -> PIC16F150x series -> 8-bit PIC microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. Its XLP (eXtreme Low Power) technology positions it for battery-powered and energy-harvesting applications where nanoWatt sleep currents and fast wake-up times dominate design decisions. Key features include Core Independent Peripherals (CIPs) such as CLC, CWG, NCO, and multiple timers; 10-bit ADC with up to 12 channels; 5-bit DAC and PWM modules; an enhanced USART, MSSP (SPI/I2C), and an operating voltage range of 2.3V to 5.5V. The 20-QFN (4x4) package with exposed thermal pad supports compact PCB layouts while providing robust thermal dissipation for industrial temperature operation. Architecturally, the PIC16F1508 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, allowing single-cycle instruction execution except for program branches. The 4-level hardware stack, deterministic interrupt latency, and peripheral pin select (PPS) simplify firmware development in MPLAB X IDE using the XC8 compiler. The XLP technology achieves sub-µA sleep currents with retention, making the device suitable for always-on sensor nodes. Typical applications include IoT sensor nodes, battery-powered consumer products, LED lighting controls with CWG, motor-control PWM loops, and small consumer appliances requiring mixed-signal integration in a compact footprint. Designers select this part when core-independent peripherals offload the CPU and reduce firmware complexity. Designers should pay attention to the exposed pad (EP) requirement of the 20-QFN package: the EP must be soldered to the ground plane for thermal performance and mechanical reliability. Decoupling capacitors of 100nF and 10µF should be placed as close as possible to the VDD pin, and unused I/O pins should be configured as outputs low to minimize current draw. This page synthesizes distributor pricing tiers, drop-in QFN-20 alternatives, and practical layout notes not found in the standalone manufacturer datasheet, helping engineers and buyers quickly evaluate the PIC16F1508T-I/ML against comparable PIC16 family members.

Angebot Kontakt

PIC16F1508T-I/SO

PIC16F1508T-I/SO - 8-Bit MCU, 7KB Flash, 20MHz, 20-SOIC | Microchip

The Microchip Technology PIC16F1508T-I/SO is an 8-bit PIC16 microcontroller built on the enhanced mid-range core, delivering 20 MHz instruction execution (200 ns instruction cycle), 7 KB Flash program memory (4K x 14 words), and 256 B SRAM in a 20-pin SOIC (SO) wide-body package shipped on tape and reel. The part operates from 2.3 V to 5.5 V supply, integrates 18 digital I/O pins, and is qualified to the industrial -40 °C to +85 °C temperature range with the nanoWatt XLP extreme-low-power feature set for battery-friendly designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (typically Flash), working RAM, peripheral interfaces (timers, ADC, communication ports), and general-purpose I/O on one die. The PIC16F1508 belongs to the product hierarchy: microcontroller -> 8-bit MCU -> PIC16 family -> enhanced mid-range core -> Microchip mid-range portfolio, and is targeted at cost-sensitive embedded control that needs more analog and timer hardware than legacy PIC16F parts. Key features include a 10-bit ADC with up to 12 channels, a 5-bit DAC, Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), multiple 8/16-bit timers with PWM, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and I2C/SPI peripherals. The nanoWatt XLP technology delivers deep-sleep currents in the microamp range, making the device suitable for always-on battery applications. Architecturally, the PIC16F1508 uses Microchip's enhanced mid-range 14-bit instruction set with a single-cycle hardware multiplier and a vectored interrupt controller, providing deterministic real-time response. The internal 16 MHz high-accuracy oscillator (HFINTOSC, ±1% typical after calibration) supports operation without an external crystal in space-constrained designs. Typical applications include consumer appliances, LED lighting controllers, sensor nodes, low-power IoT endpoints, battery chargers, and small motor-control subsystems. Industrial use cases span HVAC actuator interfaces, simple PLC I/O expansion, and human-machine interface (HMI) button/keypad scanning. When designing with this MCU, reserve one I/O line for the In-Circuit Serial Programming (ICSP) interface and another for MCLR reset if in-circuit debugging is required; if not, internal weak pull-up on MCLR allows a smaller BOM. Always derate the maximum FOSC against VDD per the datasheet electrical characteristics to avoid oscillator instability at low voltage. This page combines current distributor pricing, drop-in same-footprint alternatives, and practical design considerations to support engineering evaluation and procurement decisions.

Angebot Kontakt

PIC16F1508T-I/SS

PIC16F1508T-I/SS - 8-bit 20MHz MCU, 7KB Flash, SSOP-20 | Microchip

The Microchip Technology PIC16F1508T-I/SS is an 8-bit PIC16F-family CMOS flash microcontroller (MCU) featuring 7KB (4K x 14) of program Flash, 256 bytes of RAM, and an 18-pin I/O count, factory-packaged in a 20-pin SSOP (Shrink Small Outline Package) and tape-and-reel shipping format. The core executes instructions at 20 MHz, giving a 200 ns instruction cycle, and the device operates from 1.8 V to 3.6 V across the industrial -40C to +85C temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working RAM, and a configurable set of peripherals (ADC, timers, communication ports) on one silicon die. Within the broader taxonomy, this part is an 8-bit microcontroller -> embedded controller -> CMOS flash MCU -> semiconductor. Microchip's PIC16F mid-range family is widely used as the system brain for low-power and cost-sensitive embedded products. Key features that differentiate the PIC16F1508 include the nanoWatt XLP extreme-low-power technology for battery-friendly designs, four Configurable Logic Cells (CLC) for hardware glue logic, a Complementary Waveform Generator (CWG) for motor and power control, a Numerically Controlled Oscillator (NCO) for precise frequency generation, and a 10-bit Analog-to-Digital Converter (ADC) with internal fixed-voltage reference. Together, these peripherals let one chip replace several discrete analog and timer ICs in compact designs. Typical applications include consumer white goods, LED lighting controllers, sensor signal conditioning, low-power IoT nodes, small motor control (fans, pumps), and battery-operated handheld products. Designers favor this part when footprint, energy budget, and BOM cost are the dominant constraints rather than raw CPU throughput. One practical design tip: respect the 3.6 V absolute maximum on VDD, route the AVSS/AVDD pair as a star to the analog reference when using the ADC, and use the CWG + NCO pair to synthesize accurate PWM and frequency outputs without burdening the CPU. This page synthesizes Microchip's PIC16F1508 datasheet, distributor pricing tiers, drop-in same-package alternatives, and practical design notes that are not consolidated in any single manufacturer or distributor document.

Angebot Kontakt

PIC16F1509-E/P

PIC16F1509-E/P - 8-Bit 20MHz 14KB FLASH 20-PDIP MCU | Microchip

The Microchip Technology PIC16F1509-E/P is an 8-bit enhanced mid-range PIC16 microcontroller based on the XLP (eXtreme Low-Power) family, integrating 14KB (8K x 14) of Flash program memory in a 20-pin PDIP through-hole package. The -E/P suffix denotes the extended (industrial) temperature grade (-40C to +125C) in a PDIP package. The device executes instructions at a 20MHz clock rate with a 200ns instruction cycle, delivering deterministic real-time control for cost-sensitive embedded applications. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory, data RAM, peripheral set, and I/O ports in a single integrated package. The PIC16F1509 belongs to the Microchip mid-range 8-bit architecture, which sits in a hierarchy of microcontroller families ranging from 8-bit baseline PIC10/PIC12 devices, through mid-range PIC16, to 16-bit PIC24 and dsPIC, and 32-bit PIC32 and ARM Cortex-M SAM devices. The mid-range 8-bit MCU remains widely deployed in consumer appliances, industrial sensors, and battery-powered IoT edge nodes where low cost, deterministic interrupt response, and low standby current are the dominant design priorities. Key features of the PIC16F1509-E/P include 14KB Flash, 512 bytes RAM, 128 bytes EEPROM, 18 digital I/O pins, a 10-bit ADC with up to 12 channels, a Numerically Controlled Oscillator (NCO) for fine-frequency synthesis, Complementary Output Generator (COG) modules for power-converter timing, and peripherals such as Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), SPI, and I2C. The XLP designation indicates ultra-low-power operation with deep-sleep currents suitable for battery- or energy-harvesting systems. The device operates across 2.3V to 5.5V supply voltage, supports internal oscillator calibration, and includes configurable logic cells (CLC) for hardware-level state-machine implementation without CPU overhead. The 20-pin PDIP package simplifies breadboarding, prototype evaluation, and through-hole assembly in low-volume production. Typical applications include LED lighting controllers and color-mixing fixtures, small home appliances and white goods, consumer electronics remote controls, sensor-conditioning front ends, IoT end-node controllers, and industrial control logic where the CLC and NCO peripherals enable custom signal generation directly in hardware. When designing with the PIC16F1509-E/P, allocate sufficient decoupling (typically 100nF plus 10uF bulk) near VDD, ensure MCLR is properly tied through a pull-up to provide clean device resets, and use the Microchip MPLAB X IDE with XC8 compiler for firmware development. Programming and debugging are supported via ICSP using tools such as PICkit 3, PICkit 4, MPLAB ICD 3, MPLAB ICD 4, or the MPLAB Snap programmer. This page consolidates distributor pricing, parametric cross-references, and engineering design notes that extend beyond the manufacturer datasheet, helping procurement and design teams accelerate component selection and PCB bring-up.

Angebot Kontakt

PIC16F1509-E/SS

PIC16F1509-E/SS - 8-bit 20MHz MCU, 14KB Flash, 20-SSOP | Microchip

The Microchip PIC16F1509-E/SS is an 8-bit enhanced mid-range PIC16 microcontroller built on a CMOS process, operating at up to 20 MHz with 200 ns instruction execution, and housed in a 20-pin SSOP (0.209 inch / 5.30 mm width) package. It integrates 14 KB of Flash program memory (8K x 14), 512 B of RAM, and 18 digital I/O pins, and is qualified for the -40C to +125C extended operating temperature range. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, RAM, and peripherals on one die. PIC16F series microcontrollers from Microchip use a RISC architecture optimized for deterministic interrupt response and low power consumption; they sit beneath the PIC18 and dsPIC families in the product hierarchy and target cost-sensitive embedded designs where simplicity and small footprint dominate. Key features of the PIC16F1509 include a 10-bit ADC, three on-chip timers, enhanced PWM, configurable logic cells (CLC), a complementary waveform generator (CWG), and the Numerically Controlled Oscillator (NCO) peripheral that enables fine-grained frequency synthesis. The device supports the XLP (eXtreme Low Power) family with nanoWatt XLP technology and operates from 2.3V to 5.5V, simplifying battery-powered designs. The extended (-E) temperature grade allows deployment in industrial and outdoor environments. The PIC16F1509 architecture uses a Harvard-style 14-bit instruction word Flash store and an 8-bit data path, with hardware stack and interrupt controller supporting low-latency response. On-chip Core Independent Peripherals (CIPs) such as the CLC and CWG execute logic and timing functions without CPU intervention, freeing the core for application code and reducing firmware complexity in mixed-signal designs. Typical applications include LED lighting control with smooth dimming, white-good appliance user interfaces, sensor signal conditioning, small motor and fan control with closed-loop PWM, and IoT edge nodes where low sleep current and integrated peripherals reduce external component count. When designing with the PIC16F1509, ensure the ICSP programming pins are routed to a debug header for in-circuit programming and verify the SSOP land pattern matches the 0.65 mm pitch. Use Microchip's MPLAB X IDE and MPLAB XC8 compiler for development, and consider the PIC16F1509-I/SS variant for the industrial -40C to +85C grade when the extended -40C to +125C grade is not required. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes not consolidated in the manufacturer datasheet. Engineers can compare the PIC16F1509 against same-family parts and third-party equivalents to optimize BOM cost, lead time, and qualification grade for their specific application.

Angebot Kontakt

PIC16F1509-I/GZ

PIC16F1509-I/GZ - 14KB Flash 8-bit MCU, 20-UQFN | Microchip

The Microchip Technology PIC16F1509-I/GZ is an 8-bit PIC® microcontroller in the PIC16F1509 family featuring 14KB Flash program memory, 512 bytes RAM, 18 I/O pins, and a 10-bit ADC. It operates up to 20 MHz from a 2.3V to 5.5V supply and is housed in a 20-pin UQFN (4x4 mm) package, making it well suited for compact, surface-mount designs. The "I" suffix denotes the industrial temperature grade (-40°C to +85°C) and the "/GZ" suffix denotes the 20-UQFN package. An 8-bit PIC microcontroller is a Harvard-architecture RISC processor designed for embedded control applications. The PIC16F1509 sits within the Microchip PIC16 mid-range family, which provides a balance of code density, peripheral integration, and low power consumption. PIC16F150x devices target cost-sensitive applications requiring mixed analog and digital I/O, such as user-interface control, sensor conditioning, and low-power IoT end nodes. Key features include 14KB self-programmable Flash, 512B SRAM, 10-bit ADC with computation, support for up to four 10-bit PWM outputs, configurable logic cells (CLC), complementary waveform generators (CWG), and zero-cross detect (ZCD) peripherals. The device supports nanoWatt XLP sleep currents as low as 20 nA in sleep mode with RTCC enabled, allowing battery-powered designs to extend operating life. Internal oscillator options up to 16 MHz reduce BOM cost by removing the external crystal. The PIC16F1509 uses an enhanced mid-range core with a 14-bit instruction word. The 49-instruction set provides deterministic execution, with most instructions completing in one instruction cycle. Integrated peripherals such as CWG, CLC, and NCO enable designers to generate waveforms and logic functions without external components, which is a notable improvement over older PIC16F baselines. Typical applications include LED lighting controllers with dimming and color mixing, small appliance controls, sensor signal conditioning, battery chargers, and consumer user-interface boards. The wide operating voltage range and XLP nanoWatt technology make it a common choice for power-aware designs. When designing with this part, ensure that the UQFN exposed pad is soldered to the PCB ground plane for thermal dissipation and that decoupling capacitors are placed as close to the VDD pins as possible. Use MPLAB X IDE and XC8 compiler for code development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a faster path from specification to qualified sourcing.

Angebot Kontakt

PIC16F1509-I/ML

PIC16F1509-I/ML - 14KB Flash 8-bit MCU, 20MHz, 20-QFN | Microchip

The Microchip Technology PIC16F1509-I/ML is a PIC® XLP™ 16F family 8-bit CMOS flash microcontroller delivering 20 MHz CPU performance with 14KB (8K x 14 words) of on-chip Flash program memory, 512 bytes of RAM, and 256 bytes of EEPROM. It is housed in a 20-pin QFN (4x4 mm) exposed-pad package and operates from 2.5V/3.3V/5V rails across an industrial -40C to +85C temperature range. What is a PIC16 microcontroller? A PIC16 is a family of 8-bit RISC microcontrollers from Microchip Technology built around a Harvard architecture and a compact enhanced mid-range instruction set. Within the broader semiconductor taxonomy, a PIC16 sits below 16-bit and 32-bit MCUs (PIC24/dsPIC, PIC32) and above simple 8-bit PIC10/PIC12 devices, while still offering deterministic interrupt response, low-power XLP sleep modes, and rich Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Numerically Controlled Oscillator (NCO), and Complementary Waveform Generator (CWG) - making PIC16F1509-I/ML useful where 8-bit simplicity must coexist with on-chip analog/digital functions. Key features of the PIC16F1509-I/ML include 18 I/O pins, four 10-bit ADC channels, two comparators, two 8-bit timers, one 16-bit timer, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), SPI/I2C, and four Configurable Logic Cells. The XLP technology delivers a typical sleep current in the sub-microamp range, making it well suited to battery-powered designs that must wake, process, and return to sleep quickly. The device is built on Microchip's enhanced mid-range 8-bit core that executes most instructions in a single 200 ns cycle at 20 MHz. The 20-pin 4x4 mm QFN with an exposed thermal pad provides a compact, low-inductance ground path, which is helpful for ADC noise performance and EMI in mixed-signal designs. On-chip CIPs let designers implement custom glue logic, waveform synthesis, and signal conditioning in hardware without burdening the CPU. Typical applications include consumer white goods and small appliances, LED lighting control with dimming and color mixing, sensor signal conditioning nodes, low-cost battery-powered IoT end nodes, capacitive touch user interfaces, and industrial control logic blocks. The PIC16F1509-I/ML is a strong fit wherever an 8-bit MCU must do more analog/digital mixing than a bare PIC10/12 while still consuming a very small PCB footprint. When designing with the PIC16F1509-I/ML, expose the central thermal pad to a continuous ground copper pour to minimize ADC ground-loop noise and to keep junction temperature within the -40C to +85C industrial range. The debug header footprint must follow Microchip's AC244051/AC244052 guidance if MPLAB ICD 3 or PICkit 3 in-circuit debugging is required in production. Power-supply decoupling should include a 100 nF ceramic close to VDD plus a bulk cap near the exposed pad. This page synthesizes distributor pricing for PIC16F1509-I/ML, drop-in alternatives that share the same 20-QFN footprint, and practical design notes that are not consolidated in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F1509-I/P

PIC16F1509-I/P - 8-bit MCU, 14KB Flash, 20MHz | Microchip

The Microchip Technology PIC16F1509-I/P is an 8-bit enhanced mid-range PIC microcontroller featuring 14KB of Flash program memory, 512 bytes of RAM, and a 20MHz internal oscillator, housed in a 20-pin PDIP through-hole package. It belongs to the PIC16F1508/1509 family which integrates Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and a 10-bit ADC with up to 18 channels. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals on one silicon die. MCUs sit below microprocessors in the embedded computing hierarchy and are designed for deterministic, low-power control tasks. The PIC16F1509 belongs to the PIC16 mid-range family, which uses Microchip's enhanced RISC architecture with a 14-bit instruction word and 200ns instruction cycle at 20MHz. PIC MCUs are widely deployed in industrial, automotive, consumer, and IoT applications because of their low cost, mature toolchain (MPLAB X IDE), and field-reprogrammable Flash. Key features of the PIC16F1509-I/P include 14KB (8192 x 14-bit words) of self-programmable Flash, 512 bytes of RAM, 256 bytes of EEPROM, 18 I/O pins, four 8-bit timers, one 16-bit timer, a 10-bit ADC with 18 channels, two comparators, and an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART). The device supports 2.3V to 5.5V operation (industrial temperature range -40C to +85C for the -I variant), and integrates multiple clock sources including a 16MHz internal oscillator and an HFINTOSC with PLL. The PIC16F1509-I/P uses Microchip's enhanced mid-range core with a hardware 8x8 multiplier, providing faster arithmetic than baseline PIC devices. The on-chip CWG and NCO peripherals enable generation of high-resolution waveforms without CPU overhead, while the CLC allows combinatorial logic to be implemented in hardware, reducing code size and latency. The integrated HFINTOSC eliminates the need for external crystals in many designs, lowering BOM cost and PCB area. Typical applications include LED lighting control using the CWG and NCO peripherals, battery charging and management with PWM-driven converters, consumer appliance control (coffee makers, small kitchen equipment), sensor signal conditioning with the on-chip op-amp and ADC, automotive interior lighting (with the -E variant qualified to AEC-Q100), and small motor control via PWM channels. The 14KB Flash provides headroom for state-machine based control firmware with lookup tables. When designing with this MCU, ensure that the configuration bits (CONFIG1/CONFIG2) are set to match the application: clock source selection, watchdog timer enable, brown-out reset voltage, and code protection. Pin 1 is the master clear (MCLR) reset; an external pull-up to VDD is required unless MCLRE is disabled. Decouple VDD with a 100nF ceramic capacitor placed as close as possible to the IC, and add a 10uF bulk capacitor on the power rail. This page synthesizes distributor pricing, parameter data, drop-in alternative PIC16F1508/1509-family variants, and design notes drawn from Microchip datasheet DS40001606D that are not presented together on any single distributor product page.

Angebot Kontakt

PIC16F1509-I/SO

PIC16F1509-I/SO - 14KB Flash 20MHz 8-bit MCU | Microchip | SOIC-20

The Microchip Technology PIC16F1509-I/SO is a 20 MHz 8-bit flash microcontroller in the PIC® XLP™ 16F family, packaged in a 20-pin SOIC (SO) with 300-mil body width. The device integrates 14 KB of flash program memory, 512 bytes of SRAM, 256 bytes of EEPROM, a 10-bit ADC, and Microchip's Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLCs), Numerically Controlled Oscillator (NCO), Complementary Waveform Generator (CWG), and Zero-Cross Detect (ZCD). A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals on one die, used to sense, decide, and actuate in embedded systems. Within the product hierarchy, the PIC16F1509 sits as: 8-bit MCU -> PIC16 enhanced mid-range -> PIC16F1xxx family -> flash MCU -> embedded microcontroller. It competes with other low-power 8-bit MCUs in the PIC16, PIC18 and ATmega/AVR families, and is positioned for cost-sensitive applications that still require modern analog and logic peripherals. Key features of the PIC16F1509 include XLP™ eXtreme Low Power technology for sub-microamp sleep currents, an integrated 16 MHz internal oscillator (factory calibrated to ±1%), 17 I/O pins with interrupt-on-change, a 10-bit ADC with up to 14 channels, two comparators, two 10-bit PWMs and four 8-bit PWMs, plus the previously mentioned CIPs. The device operates across 1.8 V to 5.5 V and is rated from -40 °C to +85 °C in the industrial "-I" temperature grade. Architecturally, the PIC16F1509 uses Microchip's enhanced mid-range 14-bit instruction core with a 200 ns instruction cycle at 20 MHz, an 8-level hardware stack, and a vectored interrupt controller. Program memory is accessed through a 14-bit wide flash bus that supports self-programmability, while data EEPROM supports single-word read/write. The CIPs allow complex timing, waveform generation, and combinational logic without CPU intervention, offloading real-time tasks and reducing firmware complexity. Typical applications include LED lighting and signage controls, consumer appliances, low-power sensor nodes, battery chargers, fan and pump controls, and general-purpose digital logic replacement. Its combination of CIPs, low power, and small footprint also suits smart-home IoT end nodes and human-machine interface (HMI) panels. When designing with this part, evaluate the internal oscillator accuracy against your serial-communication baud-rate tolerance, size the decoupling per the datasheet, and use the CLC/NCO/CWG peripherals to consolidate external glue logic. For long-term product support, verify the specific SOIC-20 ordering code (PIC16F1509-I/SO vs. PIC16F1509-E/SO vs. PIC16LF1509-I/SO) against your voltage and temperature requirements. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster component selection for engineers evaluating 8-bit flash MCUs.

Angebot Kontakt

PIC16F1509-I/SS

PIC16F1509-I/SS - 8-Bit 20MHz 14KB Flash MCU | Microchip | SSOP-20

The Microchip PIC16F1509-I/SS is an 8-bit PIC® XLP™ flash microcontroller running at up to 20 MHz instruction rate, packaged in a 20-pin SSOP with 14 KB Flash (8K x 14 words), 512 bytes RAM, and 128 bytes EEPROM. It is part of the PIC16F150x family featuring Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Numerically Controlled Oscillator (NCO), Complementary Waveform Generator (CWG), and 10-bit ADC with hardware Capacitive Voltage Divider (CVD). A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), working RAM, and peripheral I/O on one die. The 8-bit class uses a RISC architecture optimized for deterministic, low-power control of LEDs, sensors, motors, and user interfaces. PIC16F1509 sits in the mid-range PIC® family — between the baseline 8-pin PIC10/12 and the enhanced 16-bit PIC24/dsPIC families — targeting applications that need more peripherals than a PIC12 but lower cost and simpler toolchain than a 32-bit Cortex-M MCU. It belongs to the power-management-aware XLP (eXtreme Low Power) sub-family with nanoWatt sleep currents below 1 µA. Key features include 18 I/O pins with interrupt-on-change, four 10-bit PWM channels, two Capture/Compare/PWM (CCP) modules, a master I²C/SPI/EUSART peripheral, a 5-bit DAC and 10-bit ADC with automatic CVD for capacitive touch, four CLC blocks for glue-logic replacement, and an NCO for precision frequency synthesis. The on-chip 32 MHz internal oscillator eliminates external crystals in cost-sensitive designs. XLP technology enables <50 nA typical sleep current for battery applications. Typical applications are LED lighting controllers, capacitive-touch user interfaces, fan/small-motor control, and battery-powered sensor nodes. The integrated NCO can replace external DACs for tone generation or dimming, while CLCs let designers replace discrete gates/timers with on-chip logic, reducing BOM cost and PCB area.

Angebot Kontakt

PIC16F1509T-I/GZ

PIC16F1509T-I/GZ - 8-bit 20MHz MCU, 14KB Flash, 20-UQFN | Microchip

The Microchip Technology PIC16F1509T-I/GZ is an 8-bit PIC® XLP™ 16F-series microcontroller running at 20 MHz, with 14 KB (8K x 14) of Flash program memory, 512 bytes of RAM, and an integrated 10-bit ADC, housed in a 20-pin UQFN exposed-pad package (4x4 mm). The -T suffix denotes Tape & Reel packaging, the -I suffix denotes the industrial -40°C to +85°C operating range, and the /GZ suffix identifies the 20-UQFN (4x4) package with thermal pad. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and a rich set of peripherals such as ADC, timers, PWM, comparators, and communication interfaces. Within the broader hierarchy, the PIC16F1509 belongs to the 8-bit microcontroller family -> PIC16 family -> PIC® XLP™ 16F sub-family -> low-power extended-life microcontrollers, where XLP™ (eXtreme Low Power) is Microchip's branding for nanoWatt-class sleep currents under 50 nA in some modes. The device targets battery-powered and energy-harvesting designs that demand long standby life alongside deterministic 8-bit execution. Key features of this device include 18 digital I/O pins sharing pins with the ADC, hardware CWG (Complementary Waveform Generator) and NCO (Numerically Controlled Oscillator), four 10-bit PWM channels, two comparators, an on-chip 10-bit ADC with up to 18 channels, an internal 16 MHz HFINTOSC, and a peripheral pin select (PPS) module on the larger pin-count variants. The 14 KB self-programmable Flash supports in-application updates over ICSP, while 512 B of RAM handles local data and stack operations. These features make the part attractive for cost-sensitive control loops where ARM Cortex-M0+ is over-spec'd. The PIC16F1509 architecture is a Harvard-style 8-bit RISC core with a 14-bit instruction word, two-stage pipeline, and a 32 kHz low-power internal oscillator plus a calibrated 16 MHz HFINTOSC. The internal core consumes roughly 4 µA at 1 MHz and drops to the nanoWatt range in sleep, enabling coin-cell or multi-year battery deployments. The CWG/NCO peripherals can synthesize precision waveforms without CPU intervention, freeing the core for supervisory tasks. Typical applications include LED lighting and driver control (constant-current PWM), small appliance and consumer white-goods user interfaces, battery chargers, sensor conditioning front-ends, e-metering accessories, and low-cost IoT endpoints where the XLP sleep current extends service life. The wide ADC channel count also makes it useful in multi-signal monitoring nodes such as HVAC fan controllers or power-supply housekeeping blocks. Industrial designs benefit from the -40°C to +85°C operating range and IEC/UL-grade EMC robustness typical of Microchip mid-range PIC devices. When designing with this MCU, allocate at least four PCB layers or a generous copper pour beneath the exposed pad on the UQFN; thermal pad soldering is mandatory for the datasheet's θJA rating to hold, otherwise the part can overheat at high peripheral activity. Decouple VDD with a 100 nF X7R placed within 3 mm of the package and add a bulk 1-10 µF tantalum or ceramic on the same net. Leave ICSPDAT/ICSPCLK accessible for in-circuit programming and debugging through PICkit™ 3, MPLAB® Snap, or MPLAB® ICD 3. This page synthesizes distributor pricing, drop-in alternatives from the PIC16F1509 family, recommended peripheral companions, and practical layout notes that are not collected on any single manufacturer or distributor page.

Angebot Kontakt

PIC16F1509T-I/ML

PIC16F1509T-I/ML - 20MHz 8-bit XLP MCU, 14KB Flash, QFN-20

The Microchip Technology PIC16F1509T-I/ML is an 8-bit PIC microcontroller from the PIC® XLP™ 16F family, integrating 14 KB (8K x 14 words) of Flash program memory, 512 B of RAM, and a 20 MHz internal oscillator in a 20-pin QFN (4x4 mm) exposed-pad package. The -T tape-and-reel suffix and -I industrial temperature grade (-40C to +85C) make this variant the production-ready choice for high-volume surface-mount assembly. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of Harvard-architecture 8-bit microcontrollers from Microchip Technology that combine a CPU core, Flash program memory, SRAM, and on-chip peripherals (ADC, timers, PWM, communication modules) into a single IC. PIC MCUs form the entry tier of Microchip's microcontroller portfolio, sitting beneath the 16-bit dsPIC and 32-bit PIC32 families, and they target cost-sensitive embedded applications where deterministic 8-bit processing is sufficient. Key features of the PIC16F1509 include 12 I/O pins, a 10-bit ADC with up to 12 channels, enhanced PWM modules with complementary outputs, configurable logic cells (CLC), numerically controlled oscillator (NCO), and the eXtreme Low Power (XLP) technology suite that delivers sub-uA sleep currents. The device operates from 2.5 V to 5.5 V and supports in-circuit serial programming (ICSP) plus in-circuit debugging via Microchip's MPLAB Snap, PICkit, or ICD tools. Architecturally, the PIC16F1509 uses a RISC-based 8-bit core with a single-cycle instruction set and a 14-bit-wide instruction word, achieving 0.2 us instruction cycle time at 20 MHz. The integrated peripherals are mapped to dedicated peripheral pin-select (PPS) registers, allowing flexible signal routing without PCB rework. Zero Cross Detect (ZCD) and complementary waveform generator (CWG) blocks simplify TRIAC and power-converter control. Typical applications include LED lighting controllers, TRIAC-based dimmer circuits, small motor control, battery-powered sensor nodes, white-goods user interfaces, and consumer appliance control panels where low cost, low quiescent current, and a compact QFN footprint are critical design drivers. When designing with this part, route the exposed pad (EP) to a continuous ground plane for thermal dissipation and electrical grounding; missing EP soldering is a leading cause of QFN reliability failures. Decouple VDD with a 100 nF ceramic capacitor placed within 3 mm of the supply pin. This page synthesizes distributor pricing, drop-in same-family alternatives, comparison parameters, and practical QFN layout guidance not bundled in the manufacturer datasheet.

Angebot Kontakt

PIC16F1509T-I/SS

PIC16F1509T-I/SS - 14KB Flash 8-bit MCU 20MHz SSOP-20 | Microchip

The Microchip Technology PIC16F1509T-I/SS is an 8-bit PIC16 microcontroller featuring 14KB Flash program memory, 512 bytes RAM, and a 20MHz internal oscillator, housed in a 20-pin SSOP package. Operating from 1.8V to 3.6V (F-series) or 2.5V to 5.5V, it integrates nanoWatt XLP ultra-low-power technology, 18 I/O pins, and peripherals including Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and a 10-bit ADC. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as timers, ADCs, and communication interfaces. Within the broader semiconductor taxonomy, an MCU is a type of embedded processor -> microprocessor -> integrated circuit. The 8-bit PIC16F family targets low-power, cost-sensitive applications where deterministic real-time response and simple peripheral integration matter more than raw compute throughput. Key features include 14KB self-programmable Flash (8K x 14 words), 512 bytes RAM, 256 bytes EEPROM, an 11-channel 10-bit ADC, four 8-bit timers, two comparators, Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and two SPI/I2C modules. The CLC, CWG, and NCO peripherals allow hardware-implemented logic, waveform synthesis, and frequency generation without CPU intervention, offloading real-time tasks from the core. The PIC16F1509 uses a RISC-based Harvard architecture with a 14-bit instruction word and a 2-stage pipeline, delivering 20 MIPS at 20MHz. nanoWatt XLP technology offers sleep currents below 50 nA, making the part suitable for battery-powered or energy-harvesting designs. The 2.5V-5.5V operating range supports both lithium battery and 5V industrial rails. Typical applications include IoT sensor nodes, battery-powered consumer electronics, LED lighting controllers, and small motor control. The wide operating voltage and low sleep current also suit automotive body electronics and remote sensor monitoring where quiescent power dominates battery life. When designing with this device, decouple VDD with a 100 nF ceramic capacitor close to the supply pin and reserve the ICSPCLK/ICSPDAT pins for in-circuit serial programming. The MCLR pin should be tied to VDD through a 10 kohm pull-up for normal operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, accelerating engineering selection and sourcing decisions.

Angebot Kontakt

PIC16F1512-E/SO

PIC16F1512-E/SO - 8-Bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F1512-E/SO is an 8-bit enhanced mid-range PIC16 microcontroller from the PIC® XLP™ 16F family, delivering 20MHz CPU speed with 3.5KB (2K x 14 words) of Flash program memory in a 28-pin SOIC (7.50mm body width) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripheral interfaces (ADC, timers, communication ports, GPIO), and clock circuitry on one die. The PIC16F1512 belongs to the enhanced mid-range PIC16 family, positioned above baseline PIC10/12/16 parts and below the PIC18 and PIC24 architectures in Microchip's 8-bit and 16-bit taxonomy. Microcontroller -> 8-bit MCU -> PIC16 family -> PIC16F15xx sub-family -> PIC16F1512. Key features include 128 bytes of RAM, a 10-bit ADC with multiple input channels, 17 I/O pins, an internal oscillator, and Microchip's eXtreme Low Power (XLP) technology for sleep currents in the microampere range. The 'E' suffix denotes the -40C to +125C extended operating temperature grade suitable for industrial environments, while 'SO' identifies the 28-pin SOIC wide-body package supplied in tube. Architecturally, the PIC16F1512 uses a RISC Harvard core with a 14-bit instruction word and 200ns instruction execution at 20MHz. Enhanced mid-range features include a hardware stack with depth 16, interrupt controller with context saving, and peripheral modules mapped through a Special Function Register (SFR) map. The Flash memory supports in-circuit serial programming (ICSP) and self-programming under firmware control for bootloader or field-update use cases. Typical applications include sensor signal conditioning with on-chip ADC, low-power battery-powered IoT nodes, industrial control panels, white goods and appliance user interfaces, and consumer electronics where deterministic 8-bit performance at low cost is preferred over 32-bit ARM Cortex-M devices. The XLP feature makes it suitable for products that must run for years on a single coin cell or two AA batteries. When designing with this device, allocate PCB area for the ICSP header (PGD/PGC/VPP/VDD/VSS) for in-circuit programming and debugging, and verify the decoupling capacitor placement per datasheet recommendations. The internal oscillator is factory calibrated within +/-2% over voltage and temperature, eliminating an external crystal in most cost-sensitive designs. For real-time deterministic control, the PIC16F1512's fixed instruction cycle simplifies timing analysis compared with variable-cycle Cortex-M0 cores. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet, helping procurement and embedded firmware engineers compare, qualify, and source the PIC16F1512-E/SO efficiently.

Angebot Kontakt

PIC16F1512-I/MV

PIC16F1512-I/MV - 8-bit PIC MCU, 3.5KB Flash, 28-UQFN | Microchip

The Microchip Technology PIC16F1512-I/MV is a 8-bit PIC microcontroller in the PIC16F151x family, featuring 3.5KB (2K x 14 words) of Flash program memory, 128 bytes of RAM, and a 10-bit Analog-to-Digital Converter (ADC), housed in a 28-pin UQFN EP (4x4 mm) package. Operating at up to 20 MHz with an enhanced mid-range PIC16 CPU core and nanoWatt XLP (eXtreme Low Power) technology, the device supports a wide 2.5V to 5.5V supply range and is offered in an industrial -40C to +85C temperature grade (the -I suffix). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripherals such as ADC, timers, communication interfaces, and I/O ports on one silicon die. The PIC16F151x family belongs to the hierarchy: microcontroller -> embedded MCU -> 8-bit MCU -> PIC mid-range core -> Microchip PIC16F family -> semiconductor. XLP technology positions this part for battery-powered and energy-harvesting designs where sleep-mode current and wake-up time directly determine battery life. Key features include 17 I/O pins, one 10-bit ADC with multiple acquisition channels, multiple timers (Timer0, Timer1, Timer2), enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and Master Synchronous Serial Port (MSSP) supporting SPI and I2C. The device includes configurable internal oscillator options, a wide operating voltage range (2.5V to 5.5V), and very low sleep current typical of nanoWatt XLP technology. The 28-UQFN package (4x4 mm) provides a compact footprint suited to space-constrained PCB designs, while the exposed pad (EP) improves thermal dissipation for higher clock-rate operation. The PIC16F1512 utilizes Microchip's enhanced mid-range 8-bit RISC architecture with a hardware stack and single-cycle instruction execution at the system clock. Internal oscillator calibration, configurable digital I/O, and on-chip debug support via MPLAB tools simplify firmware development. The Flash memory supports self-programming, and the integrated ADC, EUSART, and MSSP peripherals address the most common embedded-sensing and connectivity tasks. Typical applications include consumer appliances, IoT edge sensor nodes, battery-operated remote controls, low-power sensor interfaces, and automotive AEC-Q100 body and convenience sub-systems. The wide voltage tolerance and industrial temperature range also make it suitable for factory automation sensor endpoints. When designing with this part, allocate PCB copper to the exposed thermal pad on the UQFN for reliable thermal performance, and place a 0.1uF decoupling capacitor close to VDD. Configure the oscillator mode (HFINTOSC, LFINTOSC, or external crystal) early in firmware to ensure timing accuracy for EUSART baud-rate generation. This page consolidates datasheet specifications, real distributor pricing tiers, same-family PIC16F15xx drop-in alternatives, and practical PCB/firmware design notes that are not assembled in any single manufacturer document.

Angebot Kontakt

PIC16F1512-I/SP

PIC16F1512-I/SP - 8-bit MCU, 3.5KB Flash, 28-Pin DIP | Microchip

The Microchip PIC16F1512-I/SP is a 28-pin 8-bit flash microcontroller in the PIC16F151x family, featuring 3.5KB (2K x 14) of program Flash memory, 128 bytes of RAM, and a 10-bit ADC, all housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It is built on Microchip's enhanced mid-range PIC16 core using CMOS flash technology and supports a maximum clock frequency of 20 MHz, delivering up to 200 ns instruction execution and 49 instruction types. The device targets cost-sensitive embedded applications where low power and small memory are sufficient, and integrates XLP (eXtreme Low Power) technology for battery-friendly operation. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, RAM, program memory, and peripherals on one die; PIC microcontrollers use a Harvard RISC architecture with separate program and data buses, allowing one instruction to be fetched per clock cycle. Within the broader taxonomy, the PIC16F1512 belongs to: 8-bit MCU -> Microchip PIC16 family -> enhanced mid-range core -> flash-based MCU -> general-purpose embedded controller. It is one of the lowest-memory members of the PIC16F151x family, which scales up to the PIC16F1519 with 14KB Flash. Key features include 17 I/O pins, one 10-bit ADC with up to 17 channels, 2 comparators, 2 Enhanced Universal Synchronous/Asynchronous Receiver/Transmitters (EUSART) with LIN support, and 2 capture/compare/PWM (CCP) modules. The part runs from 1.8V to 5.5V VDD and consumes as little as 20 nA in sleep mode with the watchdog disabled, making it suitable for battery-powered designs. On-chip debug is supported through the MPLAB Snap or PICkit programmers via the ICSP interface. Typical applications include consumer appliances, small sensor nodes, remote controls, low-end LED lighting controllers, battery chargers, and educational/hobbyist projects. The 28-pin DIP package allows easy breadboard prototyping and hand-soldering, making it popular in teaching labs and through-hole production runs. When designing with this part, allocate one of the ADC channels to a clean analog reference for accurate conversions, and keep the oscillator layout short to avoid noise pickup. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC16F1512-I/SS

PIC16F1512-I/SS - 8-bit XLP MCU, 3.5KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC16F1512-I/SS is an 8-bit PIC RISC microcontroller from the PIC® XLP 16F family, offering 3.5KB (2K x 14) of flash program memory, 128 bytes of SRAM, and a 10-bit ADC in a 28-pin SSOP package. It executes instructions at 20MHz (200ns instruction cycle) from a wide 2.5V/3.3V/5V supply range, with XLP (eXtreme Low Power) technology enabling sleep currents below typical microcontroller benchmarks for battery-powered and energy-harvesting applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), and a configurable set of peripherals such as ADCs, timers, communication interfaces (UART, SPI, I2C), and general-purpose I/O. PIC16 series microcontrollers sit within Microchip's 8-bit mid-range product family, which itself belongs to the broader microcontroller hierarchy: 8-bit MCU -> mid-range MCU -> embedded controller -> semiconductor IC. The enhanced mid-range PIC16F1512 core provides 49 instructions and 16 hardware multipliers, balancing code density with deterministic interrupt latency. Key features include nanoWatt XLP sleep currents (typical 20 nA in sleep with WDT disabled), 17 channels of 10-bit ADC with internal voltage reference, multiple timer modules, an enhanced PWM, and on-board EEPROM emulation. The wide 2.0V-5.5V VDD range (industrial -40C to +85C) allows direct operation from single-cell lithium, 2x AA, USB, or regulated 3.3V/5V rails without level shifters or external regulators. Architecturally, the device combines a 14-bit instruction word with a Harvard bus architecture (separate program and data paths) and dual oscillator support including a precision 16MHz internal HFINTOSC. The result is a deterministic, low-jitter execution engine well-suited to motor control loops, sensor sampling, and protocol timing. Typical applications include IoT sensor nodes, low-power wireless remote controls, battery-powered instrumentation, consumer white-goods control boards, and industrial sensor front-ends. Designers choose the PIC16F1512 when deterministic 8-bit execution, low sleep current, and a small-footprint 28-SSOP package are simultaneously required. When designing with this part, plan the ADC reference (use internal FVR for stable conversion independent of VDD) and reserve the ICSP/ICD pins (RB6, RB7) for in-circuit programming. The 28-SSOP footprint is widely accepted on low-cost 2-layer FR4 boards. This page synthesizes distributor pricing, drop-in SSOP alternatives, and practical design notes beyond the manufacturer datasheet summary.

Angebot Kontakt

PIC16F1512T-I/MV

PIC16F1512T-I/MV - 8-bit PIC MCU, 3.5KB Flash, 28-Pin UQFN | Microchip

The Microchip Technology PIC16F1512T-I/MV is an 8-bit PIC RISC microcontroller featuring 3.5KB of Flash program memory, 128 bytes of RAM, and 256 bytes of EEPROM, housed in a 28-pin UQFN (MV) package with an exposed thermal pad for enhanced thermal dissipation. It operates at up to 20 MHz instruction clock and supports a wide 1.8V to 5.5V supply range, with selectable 1.8V/2.5V/3.3V/5V operating points, making it compatible with both 3.3V and 5V system rails. The device integrates 17 channels of 10-bit ADC, up to 25 I/O pins, and Microchip's eXtreme Low Power (XLP) technology with nanoWatt sleep currents below 50 nA typical. An 8-bit PIC microcontroller is a compact, RISC-architecture embedded controller based on Harvard memory structure, widely used for low-cost, low-power control tasks. Within the broader taxonomy, it sits as an 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The PIC16F family specifically targets battery-powered and consumer/industrial applications where simple digital I/O, analog sensing, and minimal active-mode current draw are more important than raw compute throughput. Key features include 3.5KB self-programmable Flash with 100K erase/write cycles endurance, 256 bytes of EEPROM with 1M erase/write cycles, hardware 8-bit and 16-bit timers, two PWM modules, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and an I2C/SPI peripheral. The XLP nanoWatt technology suite includes Idle, Sleep, and Deep Sleep modes with wake-on-interrupt capability, allowing battery life to extend into multi-year range on a single coin cell for sensor and metering applications. Architecturally, the device employs a 14-bit instruction word with single-cycle execution on most instructions and a 16-level deep hardware stack, simplifying interrupt-driven firmware design. The 10-bit ADC with up to 17 input channels supports automatic channel scanning and internal fixed-voltage reference, removing the need for an external reference IC in many sensor-conditioning designs. Typical applications include low-power IoT sensor nodes, consumer remote controls, white goods and small appliance control boards, battery-powered metering (water/gas/heat), HVAC thermostatic controls, and general-purpose logic replacement. The exposed-pad UQFN-28 package reduces package footprint while improving thermal performance for thermally constrained industrial enclosures. When designing with this part, allocate a 0.1uF decoupling capacitor within 5 mm of VDD and a bulk capacitor on AVDD if the ADC is active. Configure unused I/O pins as outputs with low level to minimize sleep current. Use the MPLAB X IDE with the XC8 compiler for code development, and the MPLAB Snap or PICkit 4 for in-circuit debugging via the ICSP pins. This page synthesizes distributor pricing, drop-in same-package alternatives (PIC16F1512-I/MV, PIC16F1512-E/MV), and practical XLP design notes not collected on the manufacturer datasheet cover.

Angebot Kontakt

PIC16F1512T-I/SO

PIC16F1512T-I/SO - 3.5KB Flash 8-bit MCU 28-SOIC | Microchip

The Microchip PIC16F1512T-I/SO is an 8-bit flash microcontroller from the PIC16F151x family built on an enhanced mid-range core that executes 49 instructions across 16 stack levels, packaged in a 28-pin SOIC (SO) wide-body package and supplied on tape-and-reel (T suffix). It integrates 3.5 KB (2K x 14) of self read/write flash program memory plus 128 bytes of SRAM, supports a high-endurance data flash block in the lower 128 bytes of program memory rated for 100,000 write cycles minimum, and runs up to 20 MHz from an internal 16 MHz oscillator. The part carries the XLP (eXtreme Low Power) branding for battery-friendly applications, operates across 2.5 V / 3.3 V / 5 V rails, and is rated for the industrial -40C to +85C temperature range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, volatile and non-volatile memory, programmable I/O, and one or more peripheral blocks (timers, ADC, communication interfaces). The PIC16F1512 sits inside the broader hierarchy: microcontroller -> 8-bit MCU -> enhanced mid-range PIC16 family -> Microchip PIC16F1xxx sub-family. The "/SO" suffix denotes the 28-pin Small Outline IC package, and the "T" suffix denotes tape-and-reel packaging for SMT assembly. Designers choose 8-bit PICs like this one when the application needs deterministic timing, low quiescent current, and a small code footprint at low BOM cost. Key peripheral features include MI2C and SPI plus an EUSART with auto-baud detection, two CCP modules for capture, compare, or PWM generation, two 8-bit timers (TMR0/TMR2) plus one 16-bit timer (TMR1), a 17-channel 10-bit ADC with advanced acquisition controls, and 25 mA source/sink I/O capable of driving LEDs directly. Internal voltage reference, comparator, and power-managed sleep modes round out the analog/mixed-signal set. The XLP designation indicates the part is optimized for nanoWatt sleep currents suitable for battery-backed or energy-harvesting designs. Architecturally the device uses a 14-bit instruction word, a single-cycle hardware multiplier, and the standard PIC Harvard bus. Programming and debugging are supported through the MPLAB X IDE ecosystem using any of the MPLAB PICkit, Snap, ICD, or REAL ICE in-circuit tools; the device also supports In-Circuit Serial Programming (ICSP) via two pins (ICSPCLK/ICSPDAT). The combination of low pin count, generous ADC channels, and PWM resources makes the PIC16F1512 a common choice for sensor hubs, white-goods user interfaces, and small motor/lighting controllers. Typical applications include battery-powered IoT sensor nodes (using XLP sleep + MI2C sensors), white-goods and small-appliance control panels, LED lighting controllers driven by CCP PWM, small BLDC or brushed DC motor control via PWM + ADC feedback, industrial sensor signal conditioning with on-chip op-amp-free analog front-ends, and consumer remote controls using the EUSART or MI2C for host communication. The wide VDD range also lets it sit directly on 2-cell AA alkaline rails. When designing with this device, prioritize unused I/O as outputs tied low to minimize sleep current, and place the 0.1 uF + 10 uF VDD decoupling pair within 5 mm of the supply pins to keep ADC SNR clean at 20 MHz operation. Configure ICSPCLK/ICSPDAT with their proper pull-ups or pulldowns per the datasheet programming section to ensure reliable in-circuit programming on the production line. This page synthesizes distributor pricing, drop-in alternatives from the same Microchip PIC16F151x family, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F1513-E/SS

PIC16F1513-E/SS - 8-Bit MCU, 7KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC16F1513-E/SS is an 8-bit PIC16 enhanced mid-range microcontroller built on Microchip's XLP (eXtreme Low Power) technology platform, integrating 7KB (4K x 14) of Flash program memory, 256 bytes of RAM, and a 10-bit Analog-to-Digital Converter (ADC) in a 28-pin SSOP (5.30mm width) package. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that combines a CPU, program memory (Flash), data memory (RAM), and a rich set of peripherals (ADC, timers, communication interfaces) on a single silicon die. PIC16F MCUs sit within Microchip's broader taxonomy of 8-bit microcontrollers, which in turn fall under the wider class of microcontrollers and embedded processors in the semiconductor family. They are commonly used as low-cost, deterministic, easy-to-program control cores for embedded systems where 32-bit performance is unnecessary. Key differentiating features include a 20 MHz CPU clock (200 ns instruction cycle), 7KB Flash program memory, 256B RAM, a 10-bit ADC with up to 17 channels, and eXtreme Low Power (XLP) technology that delivers sub-microamp sleep currents suitable for battery-powered products. Integrated debug support removes the need for an external debug header, allowing direct in-circuit debugging via PICkit 3 or MPLAB ICD 3 programmers. The PIC16F1513-E/SS uses a RISC-based PIC architecture with a Harvard bus, providing deterministic interrupt latency and predictable execution timing. The 20 MHz oscillator with 4x PLL option yields up to 5 MIPS throughput, while peripherals include enhanced PWM, multiple timers, USART, and I2C/SPI master/slave interfaces. Internal voltage regulation supports operation across a 2.5V/3.3V/5V range from a single supply rail. Typical applications include consumer appliance control, low-power sensor nodes, battery chargers, LED lighting controllers, and small industrial monitoring subsystems. The integrated ADC and PWM make it well suited for closed-loop feedback applications such as temperature regulation, motor speed control, and analog signal conditioning. A key design consideration is selecting the right oscillator configuration and decoupling scheme: place a 0.1 µF ceramic decoupling capacitor close to VDD, choose between internal HF or external crystal oscillator based on timing accuracy requirements, and ensure unused I/O pins are configured as outputs low to minimize sleep current. This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F1513-I/SO

PIC16F1513-I/SO - 8-Bit 20MHz 7KB Flash MCU 28-SOIC | Microchip

The Microchip Technology PIC16F1513-I/SO is an 8-bit enhanced mid-range PIC16 family microcontroller (MCU) built on the eXtreme Low Power (XLP) platform, integrating 7KB (4K x 14 words) of Flash program memory, 256 bytes of data SRAM, and a 10-bit Analog-to-Digital Converter (ADC) in a 28-pin Small Outline IC (SOIC) package. It executes instructions at 20 MHz with a 200 ns instruction cycle and operates across an industrial temperature range of -40°C to +85°C. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and configurable peripherals onto one die. Within the broader semiconductor taxonomy, an MCU sits below a microprocessor (MPU) in system complexity but above bare logic ICs, and 8-bit devices remain the dominant choice for cost- and power-sensitive embedded control where MHz-class MIPS throughput and modest memory are sufficient. Key features include 7KB of self-programmable Flash with memory partitioning support, a 10-bit ADC with up to 17 channels, enhanced PWM modules, multiple communication peripherals (I²C/SPI/EUSART), and a wide operating voltage range from 2.5V to 5.5V. The XLP nanoWatt technology brings active current draw as low as 30 µA/MHz and sleep currents down to 50 nA, enabling multi-year battery operation in remote sensor nodes. Integrated debug support means no separate debug header is required - a PICkit 3 or MPLAB ICD 3 connects directly. Architecturally, the PIC16F1513 employs a RISC Harvard core with separate program and data buses, a 14-bit instruction word, and a hardware stack that supports nested subroutine calls. The internal 31 kHz to 32 MHz oscillator with PLL and Fail-Safe Clock Monitor reduces external component count, while Peripheral Pin Select (PPS) on the larger PIC16F151x variants offers flexible signal routing for space-constrained layouts. Typical applications include consumer white goods, battery-powered sensor transmitters, LED lighting controllers, low-end motor control, and general-purpose logic replacement. The 10-bit ADC also makes the device suitable for simple thermostat front-ends and analog sensor conditioning where a full 12-bit ADC is overkill. When designing with the PIC16F1513, prioritize sleep current budgets and total Flash endurance (typically 100K erase/write cycles) for the application lifecycle. Place a 0.1 µF decoupling capacitor adjacent to each VDD pin and keep the MCLR pull-up as short as possible to avoid spurious resets. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, plus a comparison table and FAQ optimized for engineer decision workflows.

Angebot Kontakt

PIC16F1513-I/SS

PIC16F1513-I/SS - 8-bit 20MHz 7KB Flash MCU 28-SSOP | Microchip

The Microchip Technology PIC16F1513-I/SS is an 8-bit PIC microcontroller built on the enhanced mid-range PIC16 core with XLP (eXtreme Low Power) technology, delivering up to 20 MHz instruction execution from a 7 KB (4K x 14) Flash program memory in a 28-pin SSOP package. The Industrial (-I) temperature grade supports operation from -40C to +85C and a wide 2.5V/3.3V/5V operating voltage range, with integrated peripherals including a 17-channel 10-bit ADC, multiple 8/16-bit timers, enhanced PWM, and configurable logic on select pins. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash for program, SRAM for data, EEPROM for non-volatile storage), and peripheral interfaces. The 8-bit PIC family uses a RISC-based Harvard architecture optimized for deterministic instruction execution and low power consumption, making it popular for cost-sensitive embedded applications in consumer, industrial, and low-end automotive systems. Key features of the PIC16F1513 include 256 bytes of SRAM, 256 bytes of EEPROM, 17 channels of 10-bit ADC, 2 enhanced Capture/Compare/PWM (ECCP) modules, 1 MSSP (SPI/I2C) peripheral, 1 EUSART, and a 32 kHz internal oscillator. The XLP technology provides ultra-low-power sleep currents in the nanoamp range, enabling battery-powered designs to operate for years on a single cell. The device supports in-circuit debugging via Microchip's MPLAB PICkit 3, MPLAB ICD 3, or MPLAB Snap, and programming through ICSP (In-Circuit Serial Programming) without requiring a separate debug header. Pin-compatible variants exist within the PIC16F151x family, allowing memory and peripheral scaling without PCB redesign. Typical applications include home appliances, white goods, motor control, low-cost sensor interfaces, LED lighting controllers, battery-powered IoT nodes, and remote controls. The wide operating voltage and low power make it suitable for energy harvesting designs. When designing, allocate decoupling capacitors of 0.1 uF near each supply pin, and verify ADC input impedance against the source impedance to meet acquisition time requirements. The internal oscillator accuracy is typically 1-2 percent, sufficient for UART baud rates at common values. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in the standalone Microchip datasheet to accelerate your evaluation.

Angebot Kontakt

PIC16F1513T-I/SO

PIC16F1513T-I/SO - 8-bit MCU, 7KB Flash, 28-SOIC | Microchip

The Microchip Technology PIC16F1513T-I/SO is an 8-bit PIC microcontroller based on the enhanced mid-range PIC16 core, featuring 7 KB (4K x 14) of Flash program memory, 256 bytes of data RAM, and a 20 MHz internal oscillator in a 28-pin SOIC package. The 'T' suffix denotes tape-and-reel packaging and the 'I' indicates the industrial -40C to +85C operating temperature range, making the device suitable for factory-floor and outdoor embedded deployments. It belongs to the PIC16F151x family that emphasizes Microchip's eXtreme Low Power (XLP) technology platform. An 8-bit PIC microcontroller is a CMOS RISC-based single-chip computer that executes one instruction per clock cycle (except branches), integrates Flash program memory, SRAM, EEPROM, peripherals, and I/O on a single die. The PIC16 family sits within the broader PIC MCU hierarchy (PIC10/12/14/16/18/24/32), itself under the 8-bit microcontroller taxonomy that extends to competing architectures such as Atmel AVR and 8051 derivatives. Within an embedded system, the PIC16 typically handles sensor interfacing, low-power edge processing, communication bridging, and deterministic control loops. Key specifications of the PIC16F1513 include a 10-bit Analog-to-Digital Converter (ADC) with multiple channels, multiple timers, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), Master Synchronous Serial Port (MSSP) for SPI/I2C, and up to 25 digital I/O pins. The on-board ADC operates across the 2.5V to 5.5V VDD range, allowing direct interface with low-side current shunts, thermistors, and potentiometric sensors. The XLP feature provides deep-sleep currents in the nanoampere range, extending battery life in IoT endpoints. The architecture uses a Harvard-style RISC engine with 14-bit-wide instructions and a 16-level hardware stack, balancing deterministic interrupt response with code density typical of mid-range PIC devices. Program memory is self-programmable under firmware control, enabling in-field bootloaders and parameter-block updates without an external programmer. The internal voltage reference and brown-out reset (BOR) circuitry improve analog accuracy and supply-rail robustness respectively. Typical applications include battery-powered IoT sensor nodes, industrial control front-ends, home-automation peripherals, consumer white-goods user-interface boards, and low-end motor-control or LED-driver controllers. The 28-SOIC footprint is friendly to hand-soldering and rework, supporting prototyping and small-volume production. Designers typically pair the MCU with a 32.768 kHz external crystal for RTC, an MCP1700 LDO for supply regulation, and an MCP2515 CAN transceiver when CAN connectivity is required. When designing with this MCU, allocate budget for the in-circuit serial programming (ICSP) header on every prototype board; even if firmware is finalized, ICSP enables emergency recovery after configuration-word mistakes. Use the MPLAB X IDE with the XC8 compiler and reserve one pin as a firmware-driven bootloader entry to allow field updates without physical access. This page consolidates distributor pricing, drop-in alternative recommendations, application notes, and practical design guidance not present in the bare manufacturer datasheet, helping engineers shorten BOM qualification and PCB bring-up cycles.

Angebot Kontakt

Unterkategorien

Produkte (38.000+)

PIC16F1508-I/SS - 20MHz 8-Bit MCU 7KB Flash XLP | Microchip

PIC16F1508T-I/ML - 8-bit MCU, 7KB Flash, 20MHz, 20-QFN | Microchip

PIC16F1508T-I/SO - 8-Bit MCU, 7KB Flash, 20MHz, 20-SOIC | Microchip

PIC16F1508T-I/SS - 8-bit 20MHz MCU, 7KB Flash, SSOP-20 | Microchip

PIC16F1509-E/P - 8-Bit 20MHz 14KB FLASH 20-PDIP MCU | Microchip

PIC16F1509-E/SS - 8-bit 20MHz MCU, 14KB Flash, 20-SSOP | Microchip

PIC16F1509-I/GZ - 14KB Flash 8-bit MCU, 20-UQFN | Microchip

PIC16F1509-I/ML - 14KB Flash 8-bit MCU, 20MHz, 20-QFN | Microchip

PIC16F1509-I/P - 8-bit MCU, 14KB Flash, 20MHz | Microchip

PIC16F1509-I/SO - 14KB Flash 20MHz 8-bit MCU | Microchip | SOIC-20

PIC16F1509-I/SS - 8-Bit 20MHz 14KB Flash MCU | Microchip | SSOP-20

PIC16F1509T-I/GZ - 8-bit 20MHz MCU, 14KB Flash, 20-UQFN | Microchip

PIC16F1509T-I/ML - 20MHz 8-bit XLP MCU, 14KB Flash, QFN-20

PIC16F1509T-I/SS - 14KB Flash 8-bit MCU 20MHz SSOP-20 | Microchip

PIC16F1512-E/SO - 8-Bit 20MHz 3.5KB Flash MCU | Microchip

PIC16F1512-I/MV - 8-bit PIC MCU, 3.5KB Flash, 28-UQFN | Microchip

PIC16F1512-I/SP - 8-bit MCU, 3.5KB Flash, 28-Pin DIP | Microchip

PIC16F1512-I/SS - 8-bit XLP MCU, 3.5KB Flash, 28-SSOP | Microchip

PIC16F1512T-I/MV - 8-bit PIC MCU, 3.5KB Flash, 28-Pin UQFN | Microchip

PIC16F1512T-I/SO - 3.5KB Flash 8-bit MCU 28-SOIC | Microchip

PIC16F1513-E/SS - 8-Bit MCU, 7KB Flash, 28-SSOP | Microchip

PIC16F1513-I/SO - 8-Bit 20MHz 7KB Flash MCU 28-SOIC | Microchip

PIC16F1513-I/SS - 8-bit 20MHz 7KB Flash MCU 28-SSOP | Microchip

PIC16F1513T-I/SO - 8-bit MCU, 7KB Flash, 28-SOIC | Microchip