Integrierte Schaltungen

PIC16F1518T-I/MV

PIC16F1518T-I/MV - 28KB Flash 8-bit MCU, 20MHz, UQFN-28 | Microchip

The Microchip PIC16F1518T-I/MV is an 8-bit PIC microcontroller from the PIC16F1516/1517/1518/1519 family, featuring 28KB Flash program memory, 1024 bytes RAM, a 20MHz CPU clock, and a 17-channel 10-bit ADC with voltage reference, all housed in a 28-pin UQFN (4x4 mm) package. It is part of the nanoWatt XLP (eXtreme Low Power) family, designed for ultra-low-power embedded applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals on one die. The PIC16F1518 sits in the "enhanced mid-range" category of the PIC16 architecture hierarchy: PIC16 enhanced mid-range -> PIC16F1xxx family -> 8-bit MCU -> microcontroller -> embedded computing. This taxonomy reflects how the device trades off capability, power consumption, and cost for general-purpose embedded designs. Key features include an internal 16MHz oscillator, MI2C, SPI, and EUSART with auto-baud, two CCP modules supporting Capture/Compare/PWM, two 8-bit timers (TMR0/TMR2), one 16-bit timer (TMR1), 25 mA source/sink I/O, an extended watchdog timer, and Programmable Ultra Low-Power Brown-Out Reset (ULPBOR). In-Circuit Serial Programming (ICSP) and In-Circuit Debug are supported via the MPLAB Snap toolchain. The architecture uses a 14-bit instruction word and a 16-level hardware stack, with self read/write capable Flash plus a high-endurance Data Flash block (100,000 W/E cycles) in the lower 128 bytes of program memory. Operating voltage is 2.3V-5.5V (the F variant), while the LF variant runs from 1.8V-3.6V. Typical applications include battery-powered sensor nodes, IoT edge devices, consumer appliances, low-power industrial control modules, LED lighting controllers, and small home appliances. The combination of XLP sleep currents, 17 ADC channels, and rich serial peripherals suits the device for system-management and housekeeping roles. When designing with this part, place decoupling capacitors close to VDD/AVDD/VSS pins, and use the ICSP header on every prototype board to retain debug access through the MPLAB Snap. For noise-sensitive ADC applications, allocate dedicated analog and digital supply pins as documented in the pinout table. This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found on a single manufacturer datasheet page.

Angebot Kontakt

PIC16F1518T-I/SO

PIC16F1518T-I/SO - 28KB Flash 8-bit MCU 28-SOIC | Microchip

The Microchip Technology PIC16F1518T-I/SO is an 8-bit PIC® XLP™ enhanced mid-range flash microcontroller running at 20 MHz instruction rate and packaged in a 28-pin SOIC (SO) wide-body. It integrates 28 KB (16K x 14 words) of self-read/write Flash program memory, 1024 bytes of SRAM, and 256 bytes of EEPROM, all while operating from 1.8 V to 5.5 V across the -40C to +85C industrial temperature range. A microcontroller (MCU) is a single-chip computer that integrates a processor, volatile memory, non-volatile program storage, and configurable peripherals on one die. PIC16F1xxx parts belong to the enhanced mid-range PIC16 family, which in turn falls under the 8-bit PIC® architecture, then RISC microcontrollers, then embedded controllers, then semiconductors. The eXtreme Low Power (XLP™) sub-family is optimized for battery-powered and energy-harvesting applications where quiescent current and sleep-mode leakage dominate total energy budget. Key differentiating specifications include 17 channels of 10-bit ADC with voltage reference, an internal 16 MHz high-accuracy oscillator, two CCP modules for capture/compare/PWM, MI2C + SPI + EUSART (with auto-baud) serial interfaces, 25 mA source/sink I/O drive, and a high-endurance data Flash block rated for 100,000 write/erase cycles in the lower 128 bytes of program memory. The 28-SOIC package provides 25 mA I/O drive directly to LEDs, simplifying low-pin-count human-interface designs. The PIC16F1518T-I/SO architecture implements a 14-bit instruction word with 49 instructions and 16 stack levels, giving a deterministic 200 ns instruction execution at 20 MHz. The MI2C and SPI peripherals run from the system clock with hardware address masking, while the EUSART adds RS-232/485 and LIN-master capability with auto-baud detection - useful for industrial sensor nodes. Typical applications include battery-powered IoT sensor nodes, low-cost LCD user-interface boards, low-end motor-control sub-PLDs (PWM + ADC feedback), HVAC thermostat controllers, and consumer remote controls. The wide 1.8 V to 5.5 V range lets one design migrate from 2-cell alkaline (3 V) directly to USB (5 V) without re-validating the firmware. When designing with this part, populate the MCLR pin with the recommended 10 kohm pull-up unless the in-circuit debugger requires disabling; leaving MCLR floating can cause spurious resets in noisy environments. Decouple VDD/VSS with at least 100 nF placed within 5 mm of the pins, plus a bulk 1 uF to handle ADC switching transients. This page synthesizes distributor pricing, drop-in alternatives sourced from Microchip's PIC16(L)F1516/1517/1518/1519 family datasheet, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F1518T-I/SS

PIC16F1518T-I/SS - 28KB Flash 8-bit MCU | Microchip | XLP

The Microchip Technology PIC16F1518T-I/SS is an 8-bit Flash microcontroller based on the enhanced mid-range PIC16 core, delivering 28 KB of program memory, 1024 bytes of RAM, and a 20 MHz instruction clock in a 28-pin SSOP package. It integrates a 17-channel 10-bit ADC with voltage reference, two CCP modules, MI2C, SPI, and EUSART with auto-baud, and is part of the eXtreme Low Power (XLP) PIC16F1516/1517/1518/1519 family. Operating voltage is 2.3 V to 5.5 V, with industrial temperature range -40C to +85C, and the device is supplied in Tape & Reel packaging (the -T suffix). An 8-bit microcontroller (MCU) is a single-chip computer that combines an 8-bit CPU, program memory (Flash/ROM), data memory (RAM), and integrated peripherals such as ADC, timers, and communication interfaces on a single die. The PIC16F1518 belongs to the broader taxonomy: microcontroller -> embedded controller -> semiconductor IC, and within Microchip's portfolio to the PIC16 family -> enhanced mid-range core -> XLP product line. The XLP designation signifies that the device supports nanoWatt sleep currents in the deep sub-1 uA range, which is critical for battery-powered and energy-harvesting designs where standby drain dominates total energy budget. Key differentiating specifications include 28 KB self-read/write Flash with 100,000 endurance cycles on the lower 128 bytes data Flash block, 16-level hardware stack, 49 base instructions with 200 ns minimum instruction cycle at 20 MHz, 25 mA source/sink I/O drive strength for direct LED or transistor driving, and two 8-bit timers plus one 16-bit timer. The internal 16 MHz oscillator eliminates the need for an external crystal in most designs, reducing BOM cost and PCB area. Architecturally, the PIC16F1518 uses Microchip's Harvard architecture with separate program and data buses, allowing simultaneous instruction fetch and operand access. The enhanced mid-range core adds a hardware accumulator, indexed addressing, and interrupt-on-change on multiple I/O ports, while the integrated 10-bit ADC achieves typical INL of +/-1 LSB and supports both internal and external voltage references. Typical applications include consumer appliance control, IoT sensor nodes, battery-powered instrumentation, LED lighting controllers, automotive body electronics (non-safety), and low-cost industrial sensor interfaces. The wide 2.3 V-5.5 V operating range supports both 3.3 V and 5 V system designs. When designing with this device, allocate one I/O pin as MCLR if external reset is required, ensure the PGC/PGD pair is accessible for in-circuit serial programming (ICSP), and select the appropriate oscillator configuration bits for stable operation across the full temperature range. This page synthesizes distributor pricing, drop-in alternatives within the PIC16 family, application references, and practical design notes that complement but do not duplicate the manufacturer datasheet content.

Angebot Kontakt

PIC16F1519-E/MV

PIC16F1519-E/MV - 8-bit MCU 28KB Flash 40-UQFN | Microchip

The Microchip Technology PIC16F1519-E/MV is an 8-bit PIC microcontroller from the PIC16F151x family featuring 28KB of Flash program memory, 1024 bytes of RAM, and a 10-bit ADC, housed in a 40-pin UQFN (5x5 mm) package. It operates across 1.8V to 5.5V supply voltage, runs at 20 MHz instruction rate, and integrates the eXtreme Low Power (XLP) technology that delivers nanoWatt sleep currents ideal for battery-powered designs. An 8-bit microcontroller (MCU) is a small computer-on-a-chip integrating a CPU, RAM, Flash program memory, peripherals (ADC, timers, communication interfaces), and I/O pins in a single package. PIC16F1519 belongs to the mid-range PIC16 family hierarchy: 8-bit MCU -> PIC microcontroller -> Microchip MCU -> embedded controller -> semiconductor IC. This taxonomy places it above basic PIC10/PIC12 devices and below PIC18/PIC24 families in capability. Key differentiating features of the PIC16F1519 include 28KB self-programmable Flash, 1024B SRAM, 10-bit ADC with up to 28 channels, two CCP modules, hardware SPI, I2C (MSSP), and EUSART serial interfaces, plus a 32-level hardware stack. The XLP variants achieve < 50 nA typical sleep current and < 1 µA watchdog timer current, extending battery life in always-on sensor nodes. The PIC16F1519 architecture uses a 14-bit instruction word RISC core with single-cycle execution except for branches. Internal 32 MHz oscillator and 31 kHz LF oscillator are selectable, allowing flexible clock trees. The device supports In-Circuit Serial Programming (ICSP) and In-Circuit Debug (ICD) via MPLAB Snap, PICkit, or ICD headers, enabling rapid firmware iteration. Typical applications include industrial sensor nodes, low-power IoT endpoints, battery-powered HVAC controls, consumer white goods, and small appliances. The PIC16F1519 is particularly suited to applications needing more Flash (28KB) than the PIC16F1503/1507/1508/1509 baseline but without stepping up to PIC18 or dsPIC32 cost. When designing with the PIC16F1519, ensure VDDCORE decoupling with 0.1 µF + 10 µF caps adjacent to the pins. The 40-UQFN exposed pad must be soldered to a ground pour for thermal dissipation. The EUSART bootloadable firmware feature requires careful bootloader memory-region mapping. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes for the PIC16F1519-E/MV - information not consolidated on the manufacturer datasheet alone.

Angebot Kontakt

PIC16F1519-E/P

PIC16F1519-E/P - 8-Bit 20MHz MCU 28KB Flash 40-PDIP | Microchip

The Microchip Technology PIC16F1519-E/P is an 8-bit PIC® XLP™ flash microcontroller delivering 20 MIPS from a 20 MHz internal oscillator, 28 KB (16K x 14) of program Flash, 1024 bytes of RAM, and 10-bit ADC channels in a 40-pin PDIP through-hole package. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path. It belongs to the taxonomy microcontroller -> embedded controller -> semiconductor IC and is the workhorse of low-power, cost-sensitive embedded designs. Within Microchip's portfolio the PIC16F1519 sits in the enhanced mid-range PIC16 family, which adds multiple hardware peripherals, a 14-bit instruction word, and the eXtreme Low Power (XLP) feature set while retaining the classic 35-instruction RISC core. PIC microcontrollers in general, and the PIC16F1519 in particular, are widely used where deterministic interrupt latency, ultra-low sleep current, and a mature MPLAB X toolchain matter more than raw CPU throughput. Key features highlighted by the Microchip PIC16F1519 datasheet include 28 KB self-programmable Flash with code protection, 1024 bytes SRAM, up to 17 channels of 10-bit ADC, two 8-bit timers and one 16-bit timer, a master synchronous/asynchronous serial port (MSSP) configurable as SPI or I2C, an enhanced USART, four capture/compare/PWM modules (CCP), two 10-bit PWMs, an on-chip voltage reference, and an extended watchdog timer. The XLP variants add nanoWatt XLP sleep currents measured in tens of nanoamps and a wide 1.8 V to 5.5 V operating range, making the part a fit for battery-powered and energy-harvesting products. The PIC16F1519-E/P uses Microchip's enhanced mid-range core with a hardware multiplier, a single-cycle instruction decoder, and a deep interrupt controller. The 40-pin PDIP package exposes 36 I/O pins across multiple ports (RA, RB, RC, RD, RE), supports in-circuit serial programming (ICSP) via two dedicated pins, and integrates a precision 32 kHz oscillator source for low-power timing. Power management includes multiple sleep modes, brown-out reset (BOR), low-voltage detect, and an ultra-low-power watchdog that together allow idle current budgets well under 1 µA. Typical applications include industrial sensor nodes and process monitoring, white-goods and appliance control panels, low-cost medical consumables such as glucose meters, consumer remote controls and HMI boards, battery-powered metering, HVAC blower and damper control, and general-purpose 5 V logic-replacement designs migrating from 8-bit legacy controllers to a modern, flash-friendly MCU with USB-free communication. The wide operating voltage and robust peripheral mix also make the PIC16F1519 a popular choice in educational and maker platforms. When designing with this device, budget decoupling: place a 100 nF ceramic VDD bypass close to every VDD/SS pair, add a bulk 10 µF tantalum or aluminum polymer cap at the regulator output, and tie unused I/O pins to defined logic levels to avoid shoot-through current. For noise-sensitive ADC readings, average multiple samples and route analog and digital ground returns back to a single star point. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the standalone manufacturer datasheet, giving procurement and engineering teams a single decision-ready reference.

Angebot Kontakt

PIC16F1519-E/PT

PIC16F1519-E/PT - 8-bit MCU, 28KB Flash, 20MHz, 44-TQFP | Microchip

The Microchip Technology PIC16F1519-E/PT is an 8-bit PIC microcontroller built on the enhanced mid-range core with 49 instructions, 16 hardware stack levels, and self read/write Flash program memory. It integrates 28 KB of Flash (16K x 14 words), 1024 bytes of SRAM, and 28 channels of 10-bit ADC with voltage reference, packaged in a 44-pin TQFP (10x10 mm, PT suffix). A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and programmable peripherals (ADC, timers, communication interfaces) into one device. PIC16F1xxx parts belong to the PIC16 family of 8-bit MCUs, which itself sits within the broader Microchip PIC microcontroller hierarchy (PIC10/12/14/16/18/24/32) - these 8-bit RISC parts target low-power, deterministic, cost-sensitive embedded designs. The "F" suffix denotes Flash-based program memory allowing in-circuit reprogramming, while the "1519" identifies the specific enhanced mid-range device in the PIC16F1516/1517/1518/1519 family scaling in memory and pin count. Key features of the PIC16F1519 include up to 20 MHz operation from a 1.8 V to 5.5 V supply, eXtreme Low Power (XLP) technology, two Capture/Compare/PWM (CCP) modules, MI2C, SPI, and an EUSART with auto-baud support, plus 25 mA source/sink I/O capability. High-Endurance Flash (HEF) cells provide 128 B of non-volatile data storage, and the device supports on-chip debugging. The architecture combines a 14-bit instruction word with a Harvard-style bus, automatic interrupt context saving, and selectable internal 16 MHz oscillator. Power-saving sleep modes below 50 nA and a wide 1.8-5.5 V operating range make the part well suited to battery-powered and energy-harvesting designs that still require ADC precision and multiple serial interfaces. Typical applications include industrial sensor nodes, low-power IoT endpoints, home appliances, white goods control boards, automotive body and interior modules, USB-to-UART bridges, and general-purpose embedded control. Two 8-bit timers (TMR0/TMR2) plus one 16-bit timer provide flexible PWM and event timing. When designing with the PIC16F1519-E/PT, ensure decoupling capacitors are placed within 5 mm of VDD pins, keep analog and digital grounds separated via a star topology, and budget for at least four layers when routing 28 ADC channels. Avoid using both ADC and digital switching on adjacent pins without isolation. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet, helping engineers accelerate sourcing and PCB bring-up decisions.

Angebot Kontakt

PIC16F1519-I/MV

PIC16F1519-I/MV - 8-Bit 20MHz MCU, 28KB Flash, 40-UQFN | Microchip

The Microchip Technology PIC16F1519-I/MV is an 8-bit PIC microcontroller built on the nanoWatt XLP extreme-low-power architecture, delivering 20 MHz CPU performance with 28KB (16K x 14 words) of Flash program memory and 1024 bytes of SRAM in a 40-pin UQFN (5x5 mm) package. The -I suffix indicates the industrial temperature grade of -40C to +85C, and the /MV suffix designates the UQFN-40 surface-mount package. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The PIC16F1519 belongs to Microchip's PIC16F mid-range family, sitting between 8-bit MCUs and 16-bit/32-bit MCUs in the embedded control taxonomy (MCU -> 8-bit MCU -> PIC16 -> PIC16F mid-range -> enhanced mid-range core). It targets applications requiring low power consumption, generous analog integration, and easy in-system reprogrammability. Key features include 28KB self-programmable Flash, 1024B SRAM, 256B EEPROM, a 10-bit ADC with up to 28 channels, two analog comparators, an 8-bit DAC, multiple 8/16-bit timers, and serial peripherals including I2C, SPI, and EUSART. The XLP nanoWatt technology drives active current down to approximately 50 uA/MHz and sleep current below 50 nA typical with RTC, enabling battery-powered designs. The device uses an enhanced mid-range 8-bit RISC core with 49 instructions and a 16-level hardware stack. The internal 16 MHz oscillator (with PLL) and a 31 kHz low-power oscillator allow flexible clocking for active-run vs deep-sleep power optimization. ICSP (In-Circuit Serial Programming) and the standard 4-wire programming/debug interface are supported, making the part compatible with MPLAB X IDE, XC8 compilers, and PICkit/Snap/MPLAB ICD debuggers. Typical applications include IoT sensor nodes, home-automation and white-goods user-interface panels, battery-powered measurement instruments, industrial-control auxiliary logic, low-end motor-driver sequencers, and consumer electronics that need reliable 8-bit control with strong analog and low-power characteristics. The 40-UQFN package provides a compact footprint for space-constrained designs. When designing with this MCU, allocate PCB area for the decoupling capacitor cluster (0.1 uF on each VDD pin plus bulk), expose the ICSPDAT/ICSPCLK pins for programming access, and verify that unused I/O pins are configured as outputs or inputs-with-pull-up to minimize sleep current. The internal oscillator trim register (OSCTUNE) should be left at factory default unless runtime frequency tuning is needed.

Angebot Kontakt

PIC16F1519-I/P

PIC16F1519-I/P - 20MHz 8-Bit 28KB Flash MCU | Microchip Technology

The Microchip Technology PIC16F1519-I/P is an 8-bit PIC RISC microcontroller with 28 KB of flash program memory, 1024 bytes of SRAM, and operation up to 20 MHz, packaged in a 40-pin PDIP. The device operates across a 1.8 V to 5.5 V supply range and provides 36 I/O lines, 28 10-bit ADC channels, three timers, two PWM modules, and serial interfaces including I2C and SPI. A PIC16-family microcontroller is an embedded processing device that combines a CPU core, program memory, data memory, and peripherals on one integrated circuit. The enhanced mid-range PIC16 architecture uses RISC-style instructions, a 16-level hardware stack, and an integrated oscillator with internal clock sources. PIC16 devices are widely used for compact control systems because they combine low component count, flexible peripheral integration, and straightforward in-circuit programming. The PIC16F1519 distinguishes itself through 16K by 14 words of flash program memory and a 200 ns instruction execution capability. Its 10-bit ADC provides 28 channels for analog measurement, while two PWM modules and three timers support motor control, dimming, periodic sensing, and general timing tasks. Brown-out detection, power-on reset, and a watchdog timer provide baseline system supervision for industrial and consumer control designs. The device operates from 1.8 V to 5.5 V and is specified over a -40°C to +85°C temperature range. Its 36 available I/O lines give designers more external signal access than smaller 28-pin members of the PIC16F151x family. A 40-pin PDIP package also simplifies prototyping and through-hole assembly where a surface-mount land pattern is unnecessary. Typical applications include industrial sensor controllers, motor and valve drivers, LED lighting control, environmental monitoring equipment, appliance control panels, and compact embedded data-acquisition modules. In designs where the analog-to-digital converter, PWM channels, and communication interfaces operate concurrently, the larger pin count reduces the need for external multiplexers or interface expanders. When laying out a board, keep decoupling capacitors close to the supply pins, route oscillator and programming signals away from sensitive analog inputs, and confirm that every used I/O line supports the intended direction and peripheral function. The -I temperature grade supports the -40°C to +85°C range, while the /P suffix identifies the through-hole 40-pin package. This page combines the manufacturer's key device specifications with application guidance, drop-in replacement analysis, comparison parameters, and practical PCB design notes. It helps engineers evaluate whether the PIC16F1519-I/P provides the required memory, analog resolution, timing resources, and package arrangement before beginning firmware and hardware development.

Angebot Kontakt

PIC16F1519-I/PT

PIC16F1519-I/PT - 8-bit 20MHz 28KB Flash MCU 44-TQFP | Microchip

The Microchip Technology PIC16F1519-I/PT is an 8-bit PIC® XLP™ flash microcontroller from the PIC16F151x family, delivering 20 MHz CPU performance with 28 KB (16K x 14 words) of Flash program memory and 1024 bytes of SRAM, housed in a 44-pin TQFP (10x10 mm) package. The -I/PT suffix indicates an industrial temperature range (-40°C to +85°C) in TQFP packaging. What is a PIC16 microcontroller? An 8-bit PIC microcontroller is a self-contained computer-on-a-chip with an 8-bit data path, Flash program memory, on-chip RAM, and integrated peripherals such as timers, ADC, UART, I2C, SPI, and PWM. PIC16 MCUs sit within the broader hierarchy of microcontroller -> embedded processor -> semiconductor device -> integrated circuit. The nanoWatt XLP variant extends this architecture with sub-µA sleep currents and sophisticated power-management peripherals, making it ideal for battery-powered applications. Key features include 28 KB Flash, 1024 bytes SRAM, a 49-instruction set, a 16-level hardware stack with overflow/underflow reset, automatic context saving on interrupts, 36 I/O pins with individually selectable weak pull-ups, multiple timer modules (Timer0, Timer1, Timer2), a 10-bit ADC with up to 28 channels, Master Synchronous Serial Port (MSSP) for SPI/I2C, and an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART) with auto-baud detection. A 10-bit Pulse-Width Modulation (PWM) module with dual outputs handles motor or LED control. The architecture employs a Harvard-design CPU with separate program and data buses, two hardware-accelerated multiply operations, and instruction pipelining that allows most instructions to execute in a single cycle at 20 MHz (50 ns instruction cycle). The nanoWatt XLP technology delivers deep-sleep current under 20 nA typical, with multiple oscillator options (HF/LF INTOSC, XT, HS, LP, EC) for power-accuracy trade-offs. Typical applications include industrial sensor nodes and 4-20 mA loop transmitters leveraging 28 ADC channels, portable consumer devices such as wearables and remote controls leveraging XLP < 1 µA sleep current, home automation gateways with LCD keypads, low-power IoT end nodes, USB-C power-delivery controllers, and educational/development boards where the 44-pin TQFP footprint simplifies prototyping. When designing with this MCU, allocate sufficient decoupling (100 nF plus bulk cap) near VDD/AVDD pins, reserve one GPIO pair for In-Circuit Serial Programming (ICSP) ICSPDAT/ICSPCLK, and verify JTAG-disabled configuration bits to free RA0-RA5 for I/O. For low-power designs, switch to INTOSC before sleep and gate peripherals with PMD bits. This page synthesizes distributor pricing, drop-in alternatives within the PIC16F151x family, and practical design notes drawn from Microchip application notes that are not aggregated on a single distributor page.

Angebot Kontakt

PIC16F1519T-I/MV

PIC16F1519T-I/MV - 28KB Flash, 8-bit XLP MCU | Microchip

The Microchip Technology PIC16F1519T-I/MV is an 8-bit PIC microcontroller built on the nanoWatt eXtreme Low Power (XLP) technology platform, delivering 28KB of Flash program memory, 1024 bytes of SRAM, and 20 MHz CPU performance in a 40-pin UQFN (MV) 5x5 mm surface-mount package. The device operates from 1.8V to 5.5V (with Flash operation from 2.3V to 5.5V per the datasheet electrical characteristics), integrates a 10-bit ADC with multiple channels, two CCP modules, and the standard PIC16F peripheral set including EUSART, MI2C/SPI, PWM, and a watchdog timer with brown-out reset and POR. An 8-bit microcontroller (MCU) is a microprocessor integrating CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), and on-chip peripherals onto a single silicon die. Within the broader taxonomy, the PIC16F1519 belongs to the PIC16F family (mid-range PIC), part of the 8-bit MCU category, which itself sits inside the microcontroller > embedded controller > semiconductor hierarchy. The "nanoWatt XLP" branding refers to Microchip's ultra-low-power process and design techniques targeting sleep currents below 1 uA, extending battery life in portable and energy-harvesting designs. The MV suffix denotes the 40-pin UQFN package; the T suffix denotes tape-and-reel packaging; the I suffix denotes the industrial -40C to +85C temperature range. Key differentiating features include 28KB Flash (16K x 14 words) with self-write capability, 1024 bytes RAM, an internal oscillator trimmed to ±1% typical accuracy, the 10-bit A/D converter with up to 28 analog channels (package-dependent), and enhanced mid-range core with 49 instructions, 16-level hardware stack, and automatic interrupt context saving. The device supports in-circuit serial programming (ICSP) and debug via MPLAB tools including the MPLAB Snap, PICkit 4, and ICD 4. Typical applications include battery-powered IoT sensor nodes, low-power wireless protocol bridging (LoRa, Sub-GHz, BLE companion controllers), industrial sensing with analog front-ends, consumer appliances, automotive body and HVAC subsystems, USB HID peripherals, and small-form-factor embedded controllers in HVAC, lighting, and home automation where code density and ultra-low sleep current matter more than raw CPU speed. Design considerations for the PIC16F1519 include layout of the 40-pin UQFN thermal/exposed pad to the ground plane for mechanical reliability, mandatory 100 nF + bulk decoupling near VDD, adherence to the in-circuit programming pin assignments (ICSPCLK/ICSPDAT), and correct configuration bit settings to enable the internal oscillator and disable unused peripherals for lowest sleep current. This page synthesizes distributor pricing, drop-in alternative MPNs from the same PIC16F family, and practical design notes not consolidated on any single manufacturer or distributor page. Specifications below are extracted from the PIC16F1519 datasheet family document and distributor listings as of 2026-09-19.

Angebot Kontakt

PIC16F15213-E/MF

PIC16F15213-E/MF - 8-bit 32MHz MCU, 3.5KB Flash | Microchip

The Microchip Technology PIC16F15213-E/MF is an 8-bit PIC microcontroller from the PIC16F152xx family, operating at up to 32MHz with 3.5KB (2K x 14) of Flash program memory, packaged in an 8-pin DFN (3x3 mm). According to the Microchip datasheet (DS40002195A), the device features a 10-bit Analog-to-Digital Converter (ADC), Peripheral Pin Select (PPS), two PWM channels, two CCP modules, hardware limit timer (HLT), and eXtreme Low-Power (XLP) Sleep mode for battery-friendly designs. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory (Flash), data memory (RAM), peripherals, and I/O on a single silicon die. The PIC16F152xx family sits within Microchip's broad 8-bit PIC microcontroller lineup, targeting cost-sensitive sensor and real-time control applications. Within the broader hierarchy, this part class spans PIC microcontroller -> 8-bit MCU -> microcontroller -> embedded controller -> semiconductor. The 8-bit data path means the ALU natively processes 8 bits per instruction cycle, balancing code density with deterministic interrupt response, which suits real-time sensing and motor-control loops. Key differentiating features include Core Independent Peripherals (CIPs) such as the 10-bit ADC with internal voltage reference, the hardware limit timer that offloads timing-critical tasks from the CPU, and the PPS module that routes digital peripherals to virtually any I/O pin. These CIPs reduce firmware complexity, shrink BOM cost, and lower active power. The device also offers standard communication modules including EUSART, SPI, and I2C, allowing it to act as a network slave or sensor hub in distributed architectures. Architecturally, the PIC16F15213 uses a Harvard RISC core with a hardware stack and a 14-bit instruction word optimized for compiled C code. The 32MHz internal oscillator eliminates the need for an external crystal in many designs, reducing both PCB area and BOM cost. Functional Safety (FuSa) features in the PIC16F152xx family make the part appropriate for applications that need self-diagnostics or fail-safe behavior. Typical applications for the PIC16F15213-E/MF include IoT sensor nodes, low-power wireless transmitters, battery-powered HVAC sensors, small appliance controls, LED lighting drivers, and consumer white goods. The combination of small footprint, low power, and standard communication peripherals positions it for designs where PCB real estate is at a premium. When designing with this MCU, allocate the ADC acquisition time carefully, place the decoupling capacitor within 3mm of the VDD pin, and confirm that PPS mapping is finalized before committing the firmware - changing PPS mappings later often requires firmware rework.

Angebot Kontakt

PIC16F15213-E/P

PIC16F15213-E/P - 8-Bit 32MHz MCU 3.5KB Flash DIP-8 | Microchip

The Microchip Technology PIC16F15213-E/P is an 8-bit PIC microcontroller featuring a 32 MHz internal oscillator, 3.5 KB (2K x 14) of Flash program memory, 256 bytes of RAM, and zero data EEPROM, packaged in an 8-pin PDIP through-hole format. It integrates a 10-bit ADC, two PWM channels, two CCP modules, hardware limit timer (HLT), watchdog timer (WDT), peripheral pin select (PPS), and communication peripherals including EUSART, SPI, and I2C. This particular variant carries the extended (-E) temperature grade and is part of Microchip's Functional Safety (FuSa) capable product line. An 8-bit microcontroller (MCU) is a programmable integrated circuit that uses an 8-bit data path to execute instructions and interface with peripherals. Microcontrollers sit at the heart of embedded systems, hierarchically classified as: microcontroller -> embedded processor -> semiconductor -> integrated circuit. PIC microcontrollers use a modified Harvard RISC architecture, separating program and data buses for deterministic instruction throughput, and are widely deployed where low cost, low power, and ease of programming outweigh raw compute performance. The PIC16F15213-E/P delivers up to 32 MHz CPU performance from its internal oscillator, eliminating the need for an external crystal in many designs. Peripherals are interconnected through Peripheral Pin Select (PPS), allowing remapping of digital functions to different physical pins and simplifying PCB layout. The eXtreme Low-Power (XLP) Sleep Mode reduces quiescent current to single-digit microamps, enabling long battery life in sensor and IoT end nodes. Functional Safety support and Core Independent Peripherals (CIPs) allow safety-critical logic to be implemented without CPU intervention. Typical applications include cost-sensitive sensor interfaces, real-time control loops, low-power IoT edge nodes, and consumer appliance controls. The integrated 10-bit ADC, PWM, and EUSART/SPI/I2C interfaces cover most mixed-signal acquisition and actuation tasks. Compared to Cortex-M0 alternatives, the PIC16F15213 consumes less power in sleep mode and offers a smaller code footprint. When designing with this MCU, place a 0.1 uF decoupling capacitor as close as possible to VDD and consider using the ICSP programming header even for production boards to enable in-field firmware updates. Programming is performed via Microchip's MPLAB X IDE with XC8 compiler support.

Angebot Kontakt

PIC16F15213-E/SN

PIC16F15213-E/SN - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15213-E/SN is an 8-bit PIC microcontroller from the PIC16F152xx family, featuring 3.5KB (2K x 14 words) of Flash program memory, 256 bytes of SRAM, and 32MHz internal oscillator speed, housed in an 8-pin SOIC (SN) package with the -40C to +125C extended temperature grade. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash for program storage, SRAM for runtime data, and EEPROM for non-volatile data), and peripherals onto one die. The PIC16F152xx family belongs to the 8-bit microcontroller category within the broader semiconductor hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor device. These MCUs are designed for cost-sensitive sensor and real-time control applications where deterministic behavior, low power, and compact packaging matter more than raw computational throughput. Key features of the PIC16F15213-E/SN include Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and 10-bit ADC with Computation (ADC2). Peripheral Pin Select (PPS) allows flexible signal routing, while the EUSART, SPI, and I2C communication peripherals enable standard serial connectivity. The device operates across 1.8V to 5.5V supply voltage with eXtreme Low-Power (XLP) sleep currents in the nanoamp range. The architecture uses an enhanced mid-range 8-bit core with a 14-bit instruction word and 16-level hardware stack, delivering deterministic interrupt response under 100ns. Internal oscillator calibration eliminates external crystals in most designs, reducing BOM cost and PCB area. The Functional Safety (FuSa) classification reflects documentation and design practices that simplify IEC 60730 Class B safety compliance for home appliance applications. Typical applications include low-cost sensor nodes, battery-powered IoT endpoints, LED lighting controllers, HVAC sensor interfaces, home appliance control boards, and general-purpose logic replacement. The 8-pin footprint and minimal external component count make it attractive for space-constrained designs. When designing with this MCU, allocate at least one CLC block for glue logic to reduce external gates. Ensure the ICSPDAT/ICSPCLK pins are accessible for in-circuit serial programming during board bring-up. Brown-out Reset (BOR) and Low-Voltage Programming (LVP) must be properly configured in configuration words to prevent code corruption during supply transients. This page synthesizes distributor pricing, drop-in pin-compatible alternatives from the same PIC16F152xx family, and practical design notes drawn from Microchip application notes - information not consolidated on any single manufacturer or distributor page.

Angebot Kontakt

PIC16F15213-I/SN

PIC16F15213-I/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC16F15213-I/SN is an 8-bit PIC16 microcontroller running up to 32 MHz with 3.5 KB (2K x 14) Flash program memory, 256 B SRAM, and a 10-bit ADC, packaged in an 8-pin SOIC (SN) for cost-sensitive sensor and real-time control applications. According to the Microchip product page and datasheet, this part belongs to the PIC16F152xx family that features Core Independent Peripherals (CIPs), eXtreme Low-Power (XLP) modes, and Peripheral Pin Select (PPS) for flexible signal routing. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and peripheral blocks such as ADC, timers, and communication interfaces into one IC. Within the broader semiconductor hierarchy, an MCU is a sub-category of microprocessors (which exclude memory and peripherals) and falls under digital logic ICs. The PIC16F15213 belongs to the 8-bit MCU class, sitting below 16-bit and 32-bit MCUs in performance but above discrete logic in integration density. This product type is commonly used as the main control element in appliances, sensors, IoT edge nodes, and battery-powered devices where low cost and low power are more critical than raw compute throughput. Key features include 32 MHz maximum CPU clock, 3.5 KB self-read/write Flash, 256 B SRAM, a 10-bit ADC with computation, EUSART (UART) and MSSP (SPI/I2C) communication peripherals, multiple Core Independent Peripherals (CIPs), and Intelligent Analog peripherals. The wide 1.8 V to 5.5 V operating voltage range supports both 3.3 V and 5 V rails. The I/SN suffix denotes the -40C to +85C industrial temperature grade in an 8-pin SOIC package with matte-tin lead finish. The PIC16F15213 uses Microchip's enhanced mid-range 8-bit core with 49 instructions, 16 stack levels, and a 2-cycle hardware multiplier. PPS remaps digital peripheral pins onto a wide choice of I/O pads, simplifying PCB layout when UART, SPI, or PWM must be routed around other signals. The XLP feature set includes sleep currents in the nanoampere range, making the part suitable for energy-harvesting and battery-backed designs. Typical applications include IoT sensor nodes, battery-powered remote controls, low-end consumer appliances, LED lighting controllers, and functional-safety (FuSa) capable subsystems where this specific die is qualified for use in safety-related hardware per IEC 61508 SIL-2 capable documentation. When designing with this device, confirm the 8-pin I/O budget matches your application: only 6 general-purpose I/O pins are available after power and ground, so SPI plus UART sharing is generally required rather than simultaneous full-duplex operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC16F15213T-I/MF

PIC16F15213T-I/MF - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15213T-I/MF is an 8-bit PIC microcontroller from the PIC16F152xx family, providing 3.5 KB of Flash program memory and 32 MHz core performance in a compact 8-pin DFN (3x3 mm) package. Designed for cost-sensitive sensor and real-time control applications, the device integrates a 10-bit Analog-to-Digital Converter (ADC), Peripheral Pin Select (PPS), and standard communication peripherals including EUSART, SPI, and I2C. The part is qualified as part of Microchip's Functional Safety (FuSa) MCU family, making it suitable for safety-critical embedded designs. An 8-bit microcontroller is a type of embedded processor that fetches and executes instructions on an 8-bit data bus, balancing low cost and low power consumption with sufficient computational capability for control-oriented tasks. Within the semiconductor hierarchy, an 8-bit MCU sits below 16-bit and 32-bit microcontrollers but above discrete logic ICs, serving as the simplest programmable building block for sensor interfacing, motor drive sequencing, and user I/O handling. The PIC16F152xx family is Microchip's enhanced mid-range core family positioned for price-sensitive applications where a Cortex-M0 or MSP430 may be over-specified. Key features of the PIC16F15213T-I/MF include 256 bytes of SRAM, hardware Low-Power Sleep modes (XLP), 2 PWM channels, 2 CCP modules, an EUSART module, and PPS routing that allows digital peripheral pins to be remapped to multiple I/O pins. The wide 1.8V to 5.5V operating voltage range supports both single-cell battery-powered designs and 5V industrial systems, while the integrated 10-bit ADC delivers up to 9 analog input channels for sensor acquisition. Architecturally, the PIC16F15213T-I/MF employs an enhanced mid-range 8-bit RISC core with a single-cycle instruction execution at 32 MHz, yielding up to 8 MIPS of throughput. The CIP (Core Independent Peripheral) blocks allow timers, PWM, and communication to operate without CPU intervention, freeing the core for application logic. The 8-pin DFN package exposes six general-purpose I/O pins after power and ground allocation. Typical applications include IoT sensor nodes, battery-powered remote controls, LED lighting controllers, low-end BLDC fan drivers, and simple appliance user-interface boards. The PIC16F15213T-I/MF is also commonly used as a companion controller for housekeeping and housekeeping monitoring in larger systems. When designing with this device, choose decoupling capacitors as close to the VDD pin as possible (typically 100 nF) and consider using the PPS feature to route peripherals onto convenient pins. For new designs, the 8-pin DFN (3x3 mm) footprint is small but requires careful PCB layout to ensure reliable soldering and adequate thermal dissipation. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes not found in the manufacturer datasheet, enabling engineers to evaluate the PIC16F15213T-I/MF for cost-sensitive embedded designs.

Angebot Kontakt

PIC16F15213T-I/SN

PIC16F15213T-I/SN - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F15213T-I/SN is an 8-bit enhanced Mid-Range PIC16 microcontroller offering 32MHz operation, 3.5KB Flash program memory (2K x 14 words), and 256 bytes of RAM, housed in an 8-pin SOIC (SN) package with industrial -40C to +85C temperature rating. It integrates a 10-bit ADC, two PWM modules, two CCP modules, HLT, WDT, PPS, EUSART, MSSP (SPI/I2C), and Microchip's eXtreme Low Power (XLP) Sleep mode. The 'T' suffix indicates tape and reel packaging for high-volume assembly. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data memory, and digital and analog peripherals around a compact processor core. Within the broader taxonomy, the PIC16F15213 belongs to the enhanced Mid-Range 8-bit MCU category, which itself is a subset of microcontrollers, embedded processors, and finally the semiconductor product family. 8-bit MCUs are typically selected for cost-sensitive, deterministic, low-power embedded designs where a 32-bit core is overkill. Key features of the PIC16F15213T-I/SN include Peripheral Pin Select (PPS) for flexible signal routing, Core Independent Peripherals (CIPs) that offload tasks from the CPU, and functional safety (FuSa) features for applications requiring enhanced reliability. The device supports operating voltages from 1.8V to 5.5V across its industrial temperature range and provides up to 32MHz clock operation from internal or external sources. The PIC16F15213 architecture uses a Harvard-style 14-bit instruction set with 16 stack levels and self read/write Flash, enabling field firmware updates. Its XLP Sleep mode reduces active current consumption into the nanoamp range for battery-powered sensor endpoints, while integrated CIPs like timers and PWM operate autonomously without CPU intervention. Typical applications include IoT sensor nodes, battery-powered remote controls, low-cost motor control, LED lighting controllers, and consumer appliance subsystems. The wide 1.8V to 5.5V supply range also makes the device suitable for two- to four-cell battery chemistries and 5V industrial sensor interfaces. When designing with this part, select decoupling capacitance per datasheet recommendations and route PPS-mapped signals to avoid conflicting peripheral assignments. For low-power battery operation, leverage the XLP Sleep mode in combination with interrupt-driven wake-up sources to minimize average current draw. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers quickly evaluate the PIC16F15213T-I/SN against competing 8-bit MCU solutions.

Angebot Kontakt

PIC16F15214-E/SN

PIC16F15214-E/SN - 7KB Flash 8-bit MCU 32MHz 8-SOIC | Microchip

The Microchip Technology PIC16F15214-E/SN is an 8-bit PIC microcontroller with 7KB Flash program memory, 512 bytes SRAM, and a 32 MHz internal CPU, housed in an 8-pin SOIC (SN) package. The PIC16F152xx family combines Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and Numerically Controlled Oscillator (NCO) with a 10-bit ADC, two PWM channels, two CCP modules, and standard communication peripherals including EUSART and MSSP (SPI/I2C). What is a PIC16 microcontroller? The PIC16 family is Microchip's enhanced mid-range 8-bit microcontroller architecture, sitting between the baseline PIC10/PIC12 and the high-performance PIC18/PIC24 families in Microchip's product hierarchy. PIC16 microcontrollers are widely used for cost-sensitive sensor, real-time control, and low-power embedded applications where the simplicity of an 8-bit core, mature toolchain, and low unit cost outweigh the throughput of a 32-bit MCU. The PIC16F15214 specifically belongs to the 'F1x5xxx' enhanced mid-range lineup optimized for ultra-low power (XLP) operation. Key features include eXtreme Low-Power (XLP) Sleep mode with nanoWatt technology, Peripheral Pin Select (PPS) for flexible I/O mapping, a Windowed Watchdog Timer (WWDT) and Hardware Limit Timer (HLT) for functional safety, and 49 instructions with a 16-level hardware stack. The part carries the 'Functional Safety (FuSa)' designation and is supported by MPLAB X IDE, XC8 compilers, and the MPLAB Code Configurator (MCC) for rapid firmware development. Technically, the device operates from 1.8V to 5.5V across the -40C to +125C industrial temperature range, with brown-out reset (BOR), power-on reset (POR), and on-chip voltage reference. The PIC16F15214 supports in-circuit serial programming (ICSP) via two pins, enabling field updates and factory provisioning. Peripherals are mapped via PPS to maximize pin reuse across the limited 8-pin package. Typical applications include IoT sensor nodes, low-power battery-powered remote controls, appliance control boards, LED lighting controllers, simple motor-driver interfaces, and compact industrial sensor nodes. The 8-SOIC footprint is ideal for hand-soldered prototypes and space-constrained consumer products. The Functional Safety variant is suitable for IEC 61508 SIL-1 capable systems when paired with documented firmware techniques. When designing with this part, allocate the two PPS-capable I/O pins carefully because PPS allows remapping most digital peripherals to nearly any I/O, which is essential on an 8-pin package. Always place a 100nF decoupling capacitor within 3 mm of VDD, and use the internal 32 MHz HFINTOSC unless timing precision demands an external crystal. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F15214-I/P

PIC16F15214-I/P - 8-bit 32MHz 7KB Flash MCU, 8-PDIP | Microchip

The Microchip Technology PIC16F15214-I/P is an 8-bit PIC microcontroller from the PIC16F152xx family, featuring a 32 MHz CPU, 7 KB (4K x 14 words) of Flash program memory, and 512 bytes of RAM, housed in a through-hole 8-pin PDIP package. The part is qualified to the industrial temperature range (-40C to +85C) as indicated by the "I" suffix, and supports an operating voltage range of 1.8 V to 5.5 V across the family. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program and data memory, and programmable I/O peripherals. The PIC16F15214 belongs to the 8-bit microcontroller -> microcontrollers -> integrated circuits -> semiconductors product hierarchy, and targets cost-sensitive sensor and real-time control applications with on-chip analog and digital peripherals. Key features of the PIC16F15214 family include Core Independent Peripherals (CIPs), a 10-bit ADC with internal voltage reference, two PWM modules, two CCP modules, hardware limit timer (HLT), windowed watchdog timer (WDT), Peripheral Pin Select (PPS), EUSART, SPI, and I2C communication interfaces. The device also supports eXtreme Low-Power (XLP) Sleep modes, making it well-suited for battery-powered sensor nodes. Architecturally, the PIC16F15214 uses a RISC-based 8-bit core with a hardware stack, single-cycle instruction execution (at 32 MHz), and an internal 32 MHz oscillator. The functional-safety (FuSa) variant designation in the family datasheet indicates design support for safety-critical applications, and the device is supported by MPLAB X IDE and the MPLAB XC8 compiler toolchain. Typical applications include IoT sensor nodes, low-power remote controls, home appliance user interfaces, small motor control (fans, BLDC drivers), LED lighting controllers, and battery-powered consumer devices. The 5 I/O pins and PPS allow flexible peripheral routing within the constraints of an 8-pin footprint. When designing with this device, pay attention to the 8-pin package constraint - only 5 I/O pins are available plus the reset pin, so peripheral mapping must be planned before PCB layout. Use the PPS feature to map EUSART, SPI, or I2C functions to the most convenient pins. This page synthesizes distributor pricing, drop-in package alternatives within the same 8-PDIP footprint, and practical design notes that go beyond the manufacturer datasheet to help engineers select and source the right variant quickly.

Angebot Kontakt

PIC16F15214-I/SN

PIC16F15214-I/SN - 8-bit 32MHz 7KB Flash MCU | Microchip

The Microchip PIC16F15214-I/SN is an 8-bit PIC microcontroller running up to 32 MHz with 7 KB (4K x 14) of Flash program memory, packaged in an 8-pin SOIC (SN). It belongs to the PIC16F152xx family of low pin-count microcontrollers designed for cost-sensitive sensor and real-time control applications, and it carries Functional Safety (FuSa) support. The 'I' suffix denotes the industrial temperature grade (-40C to +85C), and 'SN' is the 8-pin SOIC package code. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and peripherals onto one silicon die. Within the broader taxonomy, the PIC16F15214 sits as: microcontroller -> embedded controller -> CMOS logic IC -> semiconductor. Microchip's PIC16 line uses a Harvard RISC core with a 14-bit instruction word, optimized for deterministic interrupt response, low power consumption, and a small code footprint. The 'F' in PIC16F15214 indicates Flash program memory, which is in-circuit re-programmable, unlike older OTP or ROM variants. Key features of the PIC16F15214 include a 10-bit Analog-to-Digital Converter (ADC) with computation, Peripheral Pin Select (PPS) for flexible signal routing, Core Independent Peripherals (CIPs) such as Configurable Logic Cells (CLC) and Complementary Waveform Generator (CWG), an enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and two SPI/I2C modules. The device supports eXtreme Low-Power (XLP) operation with active current in the tens of microamperes and deep sleep currents in the nanoampere range. Architecturally, the PIC16F15214 uses Microchip's mid-range 8-bit core with a 14-bit instruction set, 8-level hardware stack, and 32 MHz internal oscillator accuracy typically calibrated within +/-1 percent. PPS allows digital peripherals (UART, SPI, PWM, CLC outputs) and analog channels (ADC, comparators) to be remapped to most I/O pads at runtime, which reduces PCB layout constraints and accelerates design reuse across pin-count variants. Typical applications include low-end IoT sensor nodes, battery-powered remote controls, white-goods user-interface boards, automotive body electronics (non-safety critical), small appliance controls, and LED lighting controllers. The combination of small footprint, low power, and Functional Safety documentation makes it suitable for cost-driven designs that may need to scale into safety-related environments. When designing with the PIC16F15214-I/SN, engineers should budget 2 GPIO pins minimum for ICSP programming (PGx and PGx), include a 0.1 uF decoupling capacitor close to VDD, and consult the MPLAB X IDE project configuration for code-size optimization. The PPS feature means firmware must lock I/O mapping before any time-critical peripheral use, especially at first power-up after a brown-out.

Angebot Kontakt

PIC16F15214T-I/MF

PIC16F15214T-I/MF - 8-Bit MCU, 7KB Flash, 32MHz, 8-DFN | Microchip

The Microchip Technology PIC16F15214T-I/MF is an 8-bit PIC microcontroller built around a 32MHz core, integrating 7KB (4K x 14 words) of Flash program memory, 512 bytes of SRAM, and a 10-bit ADC in a compact 8-pin DFN (3x3 mm) package. Designed for Functional Safety (FuSa) applications, the device combines an XLP (eXtreme Low-Power) Sleep mode with a rich peripheral set that includes two PWM modules, two CCP capture/compare/PWM peripherals, an EUSART, and SPI/I2C interfaces, plus Peripheral Pin Select (PPS) for flexible signal routing. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and I/O peripherals. PIC microcontrollers from Microchip use a Harvard-architecture RISC core, a simplified instruction set, and an ecosystem centered on MPLAB X IDE and XC8 compilers. Within the PIC taxonomy, the PIC16F family represents mid-range 8-bit devices with Flash program memory, positioned between baseline PIC10/12 and enhanced PIC18 devices, and aimed at cost-sensitive, low-power embedded designs. The PIC16F15214T-I/MF features Core Independent Peripherals (CIPs) that execute logic without CPU intervention, enabling deterministic timing and reduced firmware overhead. The 10-bit ADC provides analog input for sensor reading, while the dual PWM and CCP peripherals support motor, lighting, and power-control loops. The XLP Sleep mode drops current consumption to nanoamp levels, making the device well-suited for battery-powered applications such as IoT sensors, remote controls, and wearable health monitors. Typical applications include consumer appliances, smart-home IoT nodes, sensor interface boards, LED lighting controllers, and low-cost motor or fan control. The 8-DFN package's 3x3 mm footprint allows placement on space-constrained boards, while the wide 1.8V to 5.5V supply range supports both single-cell Li-ion and 3.3V system rails. The Functional Safety (FuSa) designation indicates documentation and design support for IEC 61508 SIL-class applications. Designers should plan PCB layout to expose the underside thermal pad of the DFN package to a copper pour for proper grounding and thermal dissipation. The PPS feature requires configuration via firmware before alternate peripheral functions become active on shared pins. Use MPLAB X IDE with XC8 compiler and MPLAB Code Configurator (MCC) for rapid peripheral setup. This page synthesizes distributor stock data, drop-in alternative MPNs, and practical design considerations not typically collected in the manufacturer datasheet, helping engineers evaluate the PIC16F15214T-I/MF for new designs or as a substitute in existing 8-pin PIC layouts.

Angebot Kontakt

PIC16F15214T-I/SN

PIC16F15214T-I/SN - 8-bit MCU, 7KB Flash, 32MHz, 8-SOIC | Microchip

The Microchip Technology PIC16F15214T-I/SN is an 8-bit PIC microcontroller with a 32 MHz CPU, 7 KB Flash program memory (4K x 14 words), and an 8-pin SOIC package, targeted at functional-safety-capable, low-power embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, and peripheral interfaces onto one silicon die. The PIC family uses a Harvard-architecture RISC core with separate program and data buses, falling within the broader taxonomy: microcontroller -> embedded processor -> semiconductor IC. PIC16F152xx devices specifically target cost-sensitive applications that need more analog and communication capability than baseline PIC10/12/14 parts. Key differentiating features include a 10-bit ADC, two PWM modules, two CCP (Capture/Compare/PWM) peripherals, a Hardware Limit Timer (HLT), Windowed Watchdog Timer (WDT), Peripheral Pin Select (PPS), EUSART, and SPI/I2C interfaces. XLP (eXtreme Low-Power) Sleep Mode and an on-board 32 MHz oscillator deliver low active and sleep currents suited to battery and energy-harvesting applications. Architecture-wise, the PIC16F15214T-I/SN uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, a single-cycle hardware multiplier, and Core Independent Peripherals (CIPs) that offload timing-critical tasks from the CPU. The PIC16F152xx family supports the Functional Safety (FuSa) capability classification per Microchip's IEC 61508 SIL-2/3 documentation set. Typical applications include consumer white goods, LED lighting controllers, small motor control (fans, BLDC), battery-powered IoT sensor nodes, and low-cost industrial control subsystems. The 8-SOIC footprint and PPS-driven pin mapping ease integration into space-constrained layouts. A practical design tip: the PPS feature reassigns digital peripheral functions to alternative pins, simplifying PCB layout. Engineers should consult the device family datasheet for the exact peripheral-to-pin mapping table and derate total I/O loading when multiple high-current sink/source pins operate simultaneously. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16F152xx family, and practical engineering notes not consolidated in the manufacturer datasheet alone.

Angebot Kontakt

PIC16F15223-E/MG

PIC16F15223-E/MG - 8-bit MCU, 32MHz, 3.5KB Flash, 16-QFN | Microchip

The Microchip Technology PIC16F15223-E/MG is an 8-bit PIC16 microcontroller running at up to 32 MHz, integrating 3.5 KB (2K x 14 words) of Flash program memory and packaged in a 16-pin QFN (3x3 mm) with industrial -40C to +125C operating range. It belongs to the PIC16F152xx low-pin-count family that pairs Core Independent Peripherals (CIPs) with intelligent analog and standard communication modules for cost-sensitive sensor and real-time control applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a set of peripheral interfaces (ADC, timers, communication ports, GPIO) on one silicon die. Within the broader embedded hierarchy, the PIC16F15223 belongs to the 8-bit microcontroller -> PIC family -> low-pin-count MCU category. The PIC architecture is built on a Harvard structure with separate program and data buses, which lets the CPU fetch instructions while reading data simultaneously and supports deterministic instruction-cycle timing for real-time control loops. Key features of the PIC16F15223 include a 32 MHz internal oscillator, 256 bytes of RAM, 256 bytes of EEPROM, a 10-bit Analog-to-Digital Converter (ADC), and multiple Core Independent Peripherals such as Configurable Logic Cells (CLC), Numerically Controlled Oscillator (NCO), and Complementary Waveform Generator (CWG). The device also integrates UART, SPI, and I2C communication modules. Its 16-pin QFN (MG package) footprint measures only 3x3 mm, making it ideal for space-constrained designs. The architecture emphasizes eXtreme Low-Power operation with multiple idle/sleep modes and fast wake-up, drawing only a few microamps in deep sleep. This combination of CIPs and low-power modes enables autonomous sensor-node designs that can poll, process, and transmit while running from a coin cell or energy-harvesting supply. The ADC supports capacitive touch and temperature measurement via dedicated hardware channels. Typical applications include low-cost IoT sensor nodes, battery-powered home automation, LED lighting control with effect generation, small motor control via PWM/CWG, and consumer appliance user interfaces. The wide operating voltage (typically 1.8V to 5.5V) and small QFN package also make it suitable for wearable fitness bands and disposable medical sensor patches. When designing with this part, verify that your chosen programming tool (PICkit 4, MPLAB SNAP, or ICD 4) supports the PIC16F152xx family and that the ICSP programming pins (VDD, VSS, PGD, PGC) are accessible. The 16-QFN package requires careful PCB pad layout to avoid solder bridging on the 0.5 mm pitch pads and thermal pad soldering for mechanical reliability. This page consolidates distributor pricing, drop-in alternative MPNs in the same QFN-16 footprint, and design notes beyond the manufacturer datasheet to accelerate component selection and supply chain decisions.

Angebot Kontakt

PIC16F15223-E/P

PIC16F15223-E/P - 8-bit MCU, 3.5KB Flash, 32MHz, 14-PDIP | Microchip

The Microchip Technology PIC16F15223-E/P is an 8-bit PIC microcontroller from the PIC16F152xx family featuring 3.5KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and an internal 32MHz oscillator, housed in a 14-pin PDIP through-hole package. According to distributor listings, the device operates across a supply voltage range of 2.5V to 5.5V and supports low-power modes down to 1.8V at 16MHz. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data bus and a RISC or CISC core, integrating CPU, non-volatile program memory (Flash), working RAM, and a fixed set of peripherals into one package. Microcontrollers sit within the broader hierarchy of embedded processors and semiconductor ICs, alongside 16-bit and 32-bit MCUs, DSPs, and microprocessors. The 8-bit category remains dominant in cost-sensitive and low-power applications where deterministic interrupt response and a compact instruction set matter more than raw throughput. Key features of the PIC16F15223-E/P include a 10-bit ADC with up to 9 input channels, two PWM modules, two Capture/Compare/PWM (CCP) peripherals, hardware EUSART, SPI and I2C communication interfaces, peripheral pin select (PPS) for flexible signal routing, a hardware limiter timer (HLT), watchdog timer, and eXtreme Low-Power (XLP) Sleep mode. The Functional Safety (FuSa) variant classification indicates Microchip documentation supporting safety-critical designs. The PIC16F152xx architecture pairs Core Independent Peripherals (CIPs) with standard communication modules, allowing deterministic peripheral operation without CPU intervention. This architecture is well suited to mixed-signal front-end tasks that combine analog sampling, timer-driven control loops, and serial communication in firmware-light environments. Typical applications include industrial sensor nodes, low-cost consumer appliance controls, battery-powered IoT endpoints, LED lighting controllers, and small motor/valve drivers. The 14-pin PDIP form factor simplifies breadboarding and through-hole prototyping on legacy or hand-soldered designs. When designing with this part, note that the 14-pin PDIP package is pin-compatible with several siblings in the PIC16F152xx family, enabling footprint reuse across memory or peripheral variants. This page synthesizes distributor pricing, drop-in alternatives within the PIC16F152xx family, and practical design notes not aggregated in the manufacturer datasheet.

Angebot Kontakt

PIC16F15223-E/SL

PIC16F15223-E/SL - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

The Microchip PIC16F15223-E/SL is an 8-bit PIC16 microcontroller featuring 3.5KB Flash program memory, 256 bytes RAM, and a 10-bit ADC, housed in a 14-pin SOIC package. It operates at up to 32MHz from a 1.8V to 5.5V supply and integrates Core Independent Peripherals (CIPs), dual PWM/CCP modules, and standard communication peripherals (EUSART, SPI, I2C) for embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash/ROM), working RAM, and on-chip peripherals such as ADCs, timers, and communication interfaces. The PIC16 family sits in Microchip's 8-bit mid-range portfolio (microcontroller -> 8-bit MCU -> PIC16 family -> PIC16F152xx sub-family), targeting cost-sensitive and low-power embedded applications. The 8-bit PIC architecture uses a modified Harvard design with separate program and data buses, delivering deterministic instruction execution. Core Independent Peripherals (CIPs) are hardware blocks that operate without CPU intervention, offloading tasks such as signal generation, sequencing, and analog monitoring. Key features of the PIC16F15223 include 3.5KB Flash (2K x 14 words), 256 bytes RAM, a 10-bit ADC with multiple channels, two PWM modules plus two CCP (Capture/Compare/PWM) modules, hardware EUSART, SPI, and I2C peripherals, Peripheral Pin Select (PPS) for flexible signal routing, and eXtreme Low-Power (XLP) Sleep mode drawing typically 0.6 uA. The 14-pin SOIC (SL) package provides a compact, hand-solderable footprint suitable for through-hole-style prototyping or low-density SMT assemblies. The PIC16F152xx family uses an Enhanced Mid-Range 8-bit RISC core with a hardware multiplier, 49 instructions, and a single-cycle instruction execution at 32MHz. PPS remapping allows most digital peripherals to be assigned to multiple I/O pins, simplifying PCB layout and BOM reuse across variants. Functional Safety (FuSa) documentation and Class B safety libraries are available from Microchip, supporting IEC 60730 compliance for home appliances and similar regulated products. Typical applications include consumer appliances, low-cost sensor nodes, LED lighting controllers, battery-powered IoT endpoints, white-good control boards, and small motor/H-bridge drivers using the integrated PWM/CCP. The wide operating voltage and low sleep current also suit coin-cell or energy-harvesting designs. When designing with this part, leverage PPS to optimize pin assignments early; the 14-pin SOIC has limited dedicated peripheral pins, so PPS remapping is essential when multiple peripherals must coexist. Always provide adequate decoupling (100 nF plus 1-10 uF bulk) near VDD, and follow Microchip's Emulated EEPROM guidance if non-volatile data storage beyond the dedicated EEPROM area is required. This page synthesizes distributor pricing, drop-in package-compatible alternatives in the PIC16F152xx family, and practical design notes not found in the manufacturer datasheet summary, giving engineers a faster path from part selection to prototype.

Angebot Kontakt

Unterkategorien

Produkte (38.000+)

PIC16F1518T-I/MV - 28KB Flash 8-bit MCU, 20MHz, UQFN-28 | Microchip

PIC16F1518T-I/SO - 28KB Flash 8-bit MCU 28-SOIC | Microchip

PIC16F1518T-I/SS - 28KB Flash 8-bit MCU | Microchip | XLP

PIC16F1519-E/MV - 8-bit MCU 28KB Flash 40-UQFN | Microchip

PIC16F1519-E/P - 8-Bit 20MHz MCU 28KB Flash 40-PDIP | Microchip

PIC16F1519-E/PT - 8-bit MCU, 28KB Flash, 20MHz, 44-TQFP | Microchip

PIC16F1519-I/MV - 8-Bit 20MHz MCU, 28KB Flash, 40-UQFN | Microchip

PIC16F1519-I/P - 20MHz 8-Bit 28KB Flash MCU | Microchip Technology

PIC16F1519-I/PT - 8-bit 20MHz 28KB Flash MCU 44-TQFP | Microchip

PIC16F1519T-I/MV - 28KB Flash, 8-bit XLP MCU | Microchip

PIC16F15213-E/MF - 8-bit 32MHz MCU, 3.5KB Flash | Microchip

PIC16F15213-E/P - 8-Bit 32MHz MCU 3.5KB Flash DIP-8 | Microchip

PIC16F15213-E/SN - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

PIC16F15213-I/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15213T-I/MF - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

PIC16F15213T-I/SN - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip

PIC16F15214-E/SN - 7KB Flash 8-bit MCU 32MHz 8-SOIC | Microchip

PIC16F15214-I/P - 8-bit 32MHz 7KB Flash MCU, 8-PDIP | Microchip

PIC16F15214-I/SN - 8-bit 32MHz 7KB Flash MCU | Microchip

PIC16F15214T-I/MF - 8-Bit MCU, 7KB Flash, 32MHz, 8-DFN | Microchip

PIC16F15214T-I/SN - 8-bit MCU, 7KB Flash, 32MHz, 8-SOIC | Microchip

PIC16F15223-E/MG - 8-bit MCU, 32MHz, 3.5KB Flash, 16-QFN | Microchip

PIC16F15223-E/P - 8-bit MCU, 3.5KB Flash, 32MHz, 14-PDIP | Microchip

PIC16F15223-E/SL - 8-bit MCU, 3.5KB Flash, 32MHz | Microchip