Integrierte Schaltungen

PIC16F1526-I/MR

PIC16F1526-I/MR - 8-Bit 20MHz 14KB Flash 64-QFN MCU | Microchip

The Microchip Technology PIC16F1526-I/MR is an 8-bit PIC16 microcontroller built on Microchip's enhanced mid-range core, featuring 14 KB (8K x 14 words) of self-read/write Flash program memory, 768 bytes of RAM, and 49 instructions across 16 stack levels, in a 64-pin QFN (9x9 mm) package. The device runs up to 20 MHz from a 1.8 V to 5.5 V supply, integrates 12-bit-resolution ADC channels in a 30-channel 10-bit ADC, and includes XLP (eXtreme Low Power) technology for battery-aware designs. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, program memory, data RAM, and peripherals such as ADC, timers, and communication interfaces. Within the broader MCU taxonomy, the PIC16 family sits at the entry-level/mid-range tier of Microchip's 8-bit portfolio, between baseline PIC10/14 and high-pin-count PIC18 devices. The enhanced mid-range core adds C-friendly optimizations and a wider instruction set over the baseline PIC16 core, while keeping the deterministic, single-cycle architecture that PIC MCUs are known for. Key features of the PIC16F1526-I/MR include 30 channels of 10-bit ADC with voltage reference, two MSSP peripherals supporting SPI and I2C, an EUSART with auto-baud, ten CCP (Capture/Compare/PWM) modules, six 8-bit timers (TMR0/2/4/6/8/10), three 16-bit timers (TMR1/3/5), an extended watchdog timer (WDT), and 25 mA source/sink current capability on I/O pins for direct LED drive. Internal 16 MHz oscillator support reduces BOM cost. The PIC16F1526-I/MR uses Harvard architecture with separate program and data buses, an internal 16 MHz oscillator, and XLP technology that drops quiescent current into the microamp range during sleep. Internal voltage reference and 10-bit ADC architecture enable sensor-type signal collection, and the 30 ADC channels support multi-signal applications like sensor arrays and motor control loops. Typical applications include industrial sensor nodes, LED lighting controllers, low-power IoT endpoints, home appliances, automotive body/comfort modules, and battery-powered instrumentation. The wide 1.8 V to 5.5 V range and XLP sleep currents below 1 uA also fit energy-harvesting systems. When designing with this MCU, ensure the 64-QFN exposed pad is soldered to a sufficient ground plane for thermal dissipation. Decouple VDD with a 100 nF ceramic capacitor placed within 3 mm of the pin, and add a 10 uF bulk capacitor on the main supply rail. MPLAB X IDE with XC8 compiler is the supported toolchain. This page synthesizes distributor pricing, 64-QFN drop-in alternatives, and practical design notes not found in the standalone Microchip PIC16F1526 datasheet.

Angebot Kontakt

PIC16F1526T-I/PT

PIC16F1526T-I/PT - 8-bit PIC MCU 14KB Flash 20MHz | Microchip

The Microchip Technology PIC16F1526T-I/PT is an 8-bit PIC microcontroller from the PIC16F1 family featuring 14KB (8K x 14) of Flash program memory, 768 bytes of RAM, and a 64-pin TQFP (10x10 mm) package, operating at up to 20 MHz instruction clock with a 200 ns instruction cycle. It includes 12-bit ADC, multiple timers, EUSART, MSSP I2C/SPI, and nanoWatt XLP extreme low-power technology for energy-efficient embedded designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, Flash program memory, SRAM data memory, and peripherals (ADC, timers, communication interfaces) into one package. MCUs form the lowest tier of the embedded computing hierarchy (microcontroller -> embedded processor -> computing platform) and are classified by core architecture (here, Microchip's enhanced mid-range PIC16 RISC core) and bit-width (8-bit here vs 16-bit PIC24/dsPIC or 32-bit Cortex-M). The '16F' prefix denotes Flash-based, in-circuit-reprogrammable memory, the '1526' is the family designator, and the 'T' suffix indicates tape-and-reel packaging. Key features include 14KB Flash / 768B RAM / 256B EEPROM, 54 digital I/O pins, a 12-bit ADC with up to 30 channels, two 8-bit and five 16-bit timers, two EUSART modules, two MSSP (I2C/SPI) modules, four 10-bit PWM outputs, and nanoWatt XLP sleep currents below 1 uA. The wide 2.3V to 5.5V operating range supports both 3.3V and 5V systems. The PIC16F1526 uses Microchip's enhanced mid-range 8-bit core with a hardware multiplier, 49 instructions, and 16-level deep hardware stack. Its 200 ns instruction execution at 20 MHz provides deterministic real-time control suitable for closed-loop sensor processing, while XLP technology delivers deep-sleep currents typically under 100 nA with retention RAM intact. Typical applications include IoT sensor nodes, home appliances, industrial control panels, automotive body modules, LED lighting controllers, battery-powered instruments, and USB/serial human-machine interface (HMI) boards. The 64-pin TQFP footprint gives generous I/O for keypad scanning, LCD drive, and multi-protocol bridging. Designers should evaluate the 20 MHz clock requirement against timing budgets; for lower-power applications, leverage the XLP sleep modes with peripheral interrupt wake-up. Use MPLAB X IDE with XC8 compiler and the MPLAB Snap or PICkit programmer for development; the PIC16F1526 is supported by Microchip's Code Configurator (MCC) for rapid peripheral setup. This page synthesizes distributor pricing, same-package drop-in alternatives, and design notes beyond the manufacturer datasheet to help engineers select and qualify the PIC16F1526T-I/PT for production.

Angebot Kontakt

PIC16F1527-E/PT

PIC16F1527-E/PT - 8-bit 20MHz 28KB Flash MCU | Microchip 64-TQFP

The Microchip Technology PIC16F1527-E/PT is an 8-bit PIC16-family RISC microcontroller featuring 28KB (16K x 14) of Flash program memory, 1536 bytes of SRAM, and a maximum clock speed of 20 MHz, housed in a 64-pin TQFP (10x10 mm) package. It integrates two EUSART modules, two MSSP (I2C/SPI) modules, and ten PWM channels, supporting extensive peripheral connectivity for embedded control designs. Operating from a wide 2.5V to 5.5V supply, the device is part of the PIC® XLP™ (eXtreme Low Power) family, with sleep currents in the nanoWatt range for battery-powered applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable peripherals. The PIC16F1527 belongs to the 8-bit PIC16 family, which sits within Microchip's broader PIC microcontroller portfolio, a hierarchy running from 8-bit baseline PIC10/PIC12/PIC16, to 16-bit dsPIC/PIC24, to 32-bit PIC32. 8-bit PIC16 MCUs use a RISC Harvard architecture with separate program and data buses, executing one instruction per cycle (except branches), making them deterministic and well-suited to real-time control. The 'F' suffix denotes Flash program memory, reprogrammable in-circuit via ICSP. Key features of the PIC16F1527-E/PT include 28KB of self-programmable Flash, 1536 bytes of data RAM, two EUSART modules for asynchronous and synchronous serial communication, two MSSP modules supporting both I2C and SPI protocols, and ten enhanced PWM channels with independent timing for motor, lighting, and power-conversion control. Additional integrated peripherals include comparators, a 10-bit ADC, and configurable digital I/O. The 'E' suffix denotes the extended (-40C to +125C) industrial operating temperature range. The PIC16F1527 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word, providing higher code density than baseline PIC MCUs. The integrated nanoWatt XLP technology enables sleep currents below 1 µA, allowing battery-powered designs to last years on a single coin cell. The two EUSART and two MSSP peripherals share flexible pin mappings through the Peripheral Pin Select (PPS) subsystem, simplifying PCB layout. Typical applications include industrial automation controllers, sensor nodes for IoT systems, low-power remote control units, motor control (BLDC and stepper) front-ends, and home appliances. The 64-pin TQFP package provides up to 54 I/O pins, supporting complex user interfaces with multiple buttons, displays, and communication buses simultaneously. When designing with this device, allocate sufficient decoupling (100 nF ceramic at each VDD pin plus bulk 10 µF) and ensure the in-circuit serial programming (ICSP) lines (PGD/PGC) are accessible for production programming. For low-power designs, leverage the nanoWatt XLP sleep modes and use the on-chip low-power watchdog timer rather than an external supervisor. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and designing with the PIC16F1527-E/PT.

Angebot Kontakt

PIC16F1527-I/PT

PIC16F1527-I/PT - 8-Bit 20MHz 28KB Flash MCU | Microchip

The Microchip Technology PIC16F1527-I/PT is an 8-bit PIC16 XLP flash microcontroller delivering 20 MHz CPU performance, 28 KB (16K x 14) of program Flash, and 1536 bytes of RAM, integrated into a 64-pin TQFP (10x10 mm) package. The device executes instructions in 200 ns, combining enhanced mid-range PIC architecture with the proprietary eXtreme Low Power (XLP) technology for battery-friendly embedded control. A microcontroller (MCU) is a single-chip computer containing a CPU, program and data memory, and a rich set of peripheral interfaces such as ADC, timers, UART, I/O ports, and comparators. Within the broader semiconductor taxonomy, MCUs sit below microprocessors and above discrete logic ICs; the PIC16 family occupies the 8-bit mid-range tier between baseline PIC10/12/16 and the 16-bit dsPIC/PIC24 families. XLP technology specifically targets nanoWatt sleep currents, enabling years of operation from a single coin cell. Key features of the PIC16F1527 include 54 digital I/O pins, a 10-bit ADC with up to 30 channels, multiple Enhanced Universal Synchronous/Asynchronous Receiver/Transmitters (EUSART), SPI/I2C, up to 17 capture/compare/PWM (CCP/ECCP) channels, and a wide operating voltage range of 1.8 V to 5.5 V. The integrated 32 kHz internal oscillator and PLL-derived 32 MHz provide flexible clocking without external crystals, while nanoWatt XLP extends standby current into the sub-microamp range for sleep-dominant designs. Typical applications span consumer white goods, HVAC control, industrial sensor nodes, portable medical devices, e-metering, USB peripherals (with the on-chip full-speed USB 2.0 transceiver), and automotive body electronics (in -I and -E temperature grades). Designers frequently choose the PIC16F1527 when the application needs more than 14 KB of code space than the smaller PIC16F1519 and fewer pins than the PIC16F1526 family, but the same XLP feature set. Key design consideration: leverage XLP sleep modes aggressively, and use the internal 16 MHz HFINTOSC to eliminate the external crystal in cost-sensitive designs. Verify ADC acquisition time against source resistance using the formulas in the datasheet, especially when sampling above 100 ksps. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes drawn from the Microchip datasheet (DS40001682) plus community reference designs not found in any single source.

Angebot Kontakt

PIC16F15274-E/MP

PIC16F15274-E/MP - 8-Bit MCU, 32MHz, 7KB Flash, 40-QFN | Microchip

The Microchip Technology PIC16F15274-E/MP is an 8-bit PIC microcontroller built on a RISC architecture, delivering 32MHz CPU performance with 7KB (7K x 8) of Flash program memory in a compact 40-pin QFN (5x5 mm) package. It integrates 512 bytes of SRAM, a 10-bit ADC, two PWM channels, two CCP modules, hardware limit timer (HLT), watchdog timer, peripheral pin select (PPS), EUSART, SPI/I2C, and Microchip's eXtreme Low-Power (XLP) technology for battery-sensitive designs. A PIC microcontroller is a compact, low-cost 8-bit computing core built around a Harvard RISC architecture with separate program and data buses. PIC microcontrollers belong to the broader category of microcontrollers (MCUs), which themselves are a subcategory of embedded processors and integrated circuits. They integrate CPU, Flash, SRAM, and peripherals into a single silicon die, eliminating the need for external memory and reducing bill-of-materials cost. Within Microchip's PIC16 mid-range family, the PIC16F152xx series targets cost-sensitive sensor and real-time control applications with a balance of Core Independent Peripherals (CIPs) and standard communication interfaces. Key features of the PIC16F15274-E/MP include Core Independent Peripherals that offload timing-critical tasks from the CPU, a 10-bit Analog-to-Digital Converter for sensor interfacing, peripheral pin select (PPS) for flexible signal routing, and XLP technology that minimizes active and sleep-mode current draw. The device operates across an extended temperature range and supports in-circuit serial programming (ICSP) for field updates. From an architectural perspective, the PIC16F15274-E/MP uses a 14-bit instruction word mid-range core, with most instructions executing in a single clock cycle. The integrated peripherals are interconnected via Microchip's CIP bus, allowing logic operations such as PWM-triggered ADC sampling to occur without CPU intervention, reducing latency and power consumption in real-time control loops. Typical applications include IoT sensor nodes, low-power battery-operated devices, home appliance controls, LED lighting controllers, and industrial sensor interfaces. The 40-QFN footprint is well suited to space-constrained PCB designs that require more I/O than 14- or 20-pin variants in the same family can provide. When designing with this device, ensure that decoupling capacitors are placed as close as possible to the VDD pins, and verify the PPS mapping against your chosen peripheral assignments. Developers migrating from 14/20-pin PIC16F152xx variants gain additional I/O but must revalidate their pin allocation against the 40-QFN pinout. This page synthesizes distributor pricing, drop-in alternatives from the PIC16F152xx family and pin-compatible same-package variants, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC16F15274-E/P

PIC16F15274-E/P - 8-bit 32MHz MCU, 7KB Flash 40-PDIP | Microchip

The Microchip Technology PIC16F15274-E/P is an 8-bit PIC microcontroller featuring a 32 MHz CPU, 7 KB of Flash program memory, and 512 bytes of SRAM, housed in a 40-pin PDIP (Through-Hole) package. It integrates the eXtreme Low-Power (XLP) technology, a 10-bit ADC with computation, two PWM modules, two CCP modules, an EUSART, and both SPI/I2C peripherals, making it a versatile solution for cost-sensitive sensor and real-time control applications. A microcontroller (MCU) is a compact integrated circuit containing a processor core, memory, and programmable input/output peripherals. The PIC16F15274 belongs to the 8-bit microcontroller category, which sits below 16-bit and 32-bit MCUs in computational capacity but excels in simplicity, deterministic timing, and ultra-low power operation. Within the broader taxonomy, an MCU is a type of embedded processor -> microcontroller -> semiconductor -> integrated circuit. The PIC architecture is a RISC design known for its small instruction set, low power consumption, and robust peripherals. Key differentiating features include the Peripheral Pin Select (PPS) which allows flexible remapping of digital peripherals to any I/O pin, reducing PCB layout constraints. The 10-bit ADC with computation (ADC²) performs hardware averaging, threshold comparison, and basic filtering, offloading tasks from the CPU. The XLP technology delivers nanoWatt sleep currents, enabling battery-powered applications to run for years on a single cell. The PIC16F15274 utilizes the enhanced mid-range PIC16 CPU core with a modified Harvard architecture, providing deterministic 8-bit instruction execution. The integrated Core Independent Peripherals (CIPs) like the Hardware Limit Timer (HLT) and PWM allow complex control sequences to execute without CPU intervention, freeing the CPU for application logic. The wide operating voltage range from 1.8V to 5.5V supports both 3.3V and 5V system designs. Typical applications include IoT sensor nodes, home appliance control, LED lighting, battery management, industrial automation, and low-power edge devices. The combination of XLP technology and flexible peripherals makes it ideal for any application demanding low standby current and reliable real-time control. When designing with this device, ensure proper decoupling with 100nF ceramic capacitors placed close to VDD pins, and consider using PPS to route peripherals away from analog-sensitive pins. The 40-pin PDIP package offers easy through-hole assembly, simplifying prototyping and hobbyist projects. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing engineers with a consolidated reference for BOM decisions and cross-brand sourcing.

Angebot Kontakt

PIC16F15274-E/PT

PIC16F15274-E/PT - 8-bit MCU, 7KB Flash, 32MHz, 44-TQFP | Microchip

The Microchip Technology PIC16F15274-E/PT is an 8-bit PIC microcontroller built around a RISC core running at up to 32 MHz, integrating 7 KB of Flash program memory, 512 bytes of SRAM, and a 10-bit ADC into a 44-pin TQFP (10x10 mm) package. It belongs to the PIC16F152xx family, designed for cost-sensitive sensor and real-time control applications with Core Independent Peripherals (CIPs) and Intelligent Analog on-chip. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, and a mix of analog and digital peripherals behind a set of general-purpose I/O pins. Within the broader taxonomy, an MCU sits under microcontroller -> embedded processor -> semiconductor device, and the PIC16F15274 occupies the 8-bit mid-range tier aimed at low-power, low-cost, deterministic control. The 'F' suffix denotes Flash program memory, allowing in-circuit re-programming for development and field updates. Key features include 7 KB Flash (7K x 14 words), 512 bytes SRAM, 256 bytes EEPROM, a 10-bit ADC with internal voltage reference, two PWM modules, two Capture/Compare/PWM (CCP) peripherals, hardware limit timer (HLT), watchdog timer, Peripheral Pin Select (PPS), EUSART, SPI, and I2C. The device also carries Microchip's eXtreme Low-Power (XLP) technology for battery-driven designs, along with a 32 MHz internal oscillator that lets the BOM drop external crystals in many applications. The PIC16F15274 uses a Harvard-architecture RISC core with a 14-bit instruction word, providing deterministic single-cycle execution for most instructions. The PPS module remaps digital peripherals onto a wide range of I/O pins, simplifying board layout when signal routing changes late in the design. The 10-bit ADC combined with internal voltage reference enables accurate sensor measurements without external analog components, while the HLT peripheral offloads timing-critical tasks from the CPU. Typical applications include battery-powered sensor nodes, home appliances, LED lighting controllers, low-cost motor control, IoT edge nodes, and industrial sensor hubs. The combination of XLP sleep currents below 1 microamp and integrated peripherals makes the part well suited to mains-battery hybrids and energy-harvesting front ends. When designing with the PIC16F15274-E/PT, take care with the decoupling network - place a 100 nF X7R plus a 10 uF bulk capacitor within 3 mm of the VDD pin. The 'E' temperature grade indicates -40C to +125C operation, so margin the clock and ADC reference for thermal drift at the extremes of the range. This page synthesizes distributor pricing, drop-in alternatives within the same TQFP-44 footprint, and practical design notes that complement (but do not replace) the manufacturer datasheet.

Angebot Kontakt

PIC16F15274-I/MP

PIC16F15274-I/MP - 8-Bit 32MHz 7KB Flash MCU | Microchip | QFN-40

The Microchip PIC16F15274-I/MP is an 8-bit PIC16 microcontroller featuring 7KB of Flash program memory, 32MHz CPU speed, and 512 bytes of RAM, housed in a 40-pin QFN (5x5 mm) package with industrial temperature rating. It integrates a 10-bit ADC, two PWM modules, two CCP modules, hardware limit timer (HLT), watchdog timer, peripheral pin select (PPS), EUSART, SPI, and I2C communication peripherals, plus the eXtreme Low-Power (XLP) feature set for energy-sensitive designs. A microcontroller (MCU) is a single-chip computer integrating a CPU core, non-volatile program memory, working RAM, and programmable peripherals. The PIC16F15274 belongs to the 8-bit PIC16 family - within the broader taxonomy, this places it as: PIC16F15274 -> PIC16F152xx family -> PIC16F1xxx series -> PIC16 family -> 8-bit PIC microcontrollers -> microcontrollers -> embedded processors -> semiconductors. The 8-bit PIC architecture uses a Harvard design with separate program and data buses and a RISC-style instruction set optimized for deterministic interrupt response and low power operation. Key features of the PIC16F15274 include 7KB (7K x 14 word) self-programmable Flash, 512 bytes SRAM, 10-bit analog-to-digital converter with multiple channels, dual PWM outputs for motor or lighting control, complementary core independent peripherals (CIPs) such as the configurable logic cell and signal measurement timer, and the Intelligent Analog peripheral set. Operating voltage spans 1.8V to 5.5V, making the part suitable for both 3.3V and 5V system rails. Architecturally the device combines a 32MHz internal oscillator, instruction-cycle throughput up to 8 MIPS, and peripheral pin select (PPS) for flexible remapping of digital functions to physical pins. The XLP feature delivers nanoWatt sleep currents, allowing battery-powered nodes to remain dormant for years on a single cell. The integrated core-independent peripherals offload timing, waveform generation, and signal-conditioning tasks from the CPU. Typical applications include consumer appliances, sensor interface modules, low-cost motor control, LED lighting controllers, battery-powered IoT edge nodes, and general-purpose embedded control. The wide 1.8V-5.5V operating range and tiny QFN-40 footprint also suit space-constrained designs in industrial and home automation segments. Designers should note that the QFN-40 (5x5 mm) package requires a thermal pad soldered to a sufficient copper pour to meet the rated thermal performance. Programming is supported through Microchip's MPLAB X IDE ecosystem with XC8 compilers and PICkit programmers, and code examples are published for common tasks. This page consolidates distributor pricing, drop-in alternatives, design considerations, and application guidance drawn from the manufacturer datasheet and authorized distributors.

Angebot Kontakt

PIC16F15274-I/P

PIC16F15274-I/P - 7KB Flash 8-bit MCU, 32MHz, 40-PDIP | Microchip

The Microchip Technology PIC16F15274-I/P is an 8-bit PIC microcontroller featuring 7KB Flash program memory, 512 bytes RAM, and a 32 MHz CPU core, housed in a 40-pin PDIP (Plastic DIP) through-hole package. It integrates a 10-bit ADC, two PWM channels, two CCP modules, hardware limit timer (HLT), watchdog timer (WDT), peripheral pin select (PPS), EUSART, SPI/I2C, and eXtreme Low-Power (XLP) technology. The device operates from 2.5V to 5.5V supply across the industrial -40C to +85C temperature range. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data-path CPU core with on-chip Flash, RAM, and peripheral IP. Within the broader semiconductor hierarchy, an MCU sits inside the microcontroller category, which itself belongs to the embedded computing / digital IC family. The PIC16F152xx family specifically targets cost-sensitive sensor and real-time control applications where low power, small footprint, and analog integration matter more than raw throughput. Key features of the PIC16F15274-I/P include 7KB (7K x 8) self-programmable Flash, 512 bytes data RAM, 10-bit ADC with computation, two PWM outputs, two CCP capture/compare/PWM blocks, peripheral pin select for flexible signal routing, and eXtreme Low-Power modes such as sleep currents in the nanoamp range. The combination of CIPs (Core Independent Peripherals) and Intelligent Analog lets the CPU offload timing and signal-conditioning tasks. Architecturally, the part uses Microchip's enhanced mid-range 8-bit core with a hardware multiplier, a 32 MHz internal oscillator, and instruction cache. The 10-bit ADC is paired with an internal voltage reference and computation features (averaging, threshold comparisons), making it suitable for direct sensor digitisation without an external analog front end. Typical applications include low-cost sensor nodes, IoT edge devices, appliance control boards, LED lighting controllers, battery-powered instrumentation, and consumer electronics HMI sub-modules. The wide 2.5V-5.5V supply and XLP operation allow direct Li-ion or 2xAA battery deployment. When designing with the PIC16F15274-I/P, choose the PDIP package for prototyping or hand-soldered designs and migrate to the TQFP-44 (PIC16F15274-I/PT) for production. Always reserve the ICSP pins (PGD/PGC) for in-circuit programming and ensure Vdd decoupling is placed within 5 mm of the supply pins. This page synthesizes distributor pricing, drop-in alternative listings, and design notes not consolidated in the manufacturer datasheet, helping engineers shorten evaluation time.

Angebot Kontakt

PIC16F15274-I/PT

PIC16F15274-I/PT - 8-bit 32MHz MCU 7KB FLASH TQFP-44 | Microchip

The Microchip Technology PIC16F15274-I/PT is an 8-bit RISC microcontroller built around the PIC16 CPU core, operating at up to 32MHz, and housed in a 44-pin TQFP (10x10 mm) package. It integrates 7KB (7K x 8) of FLASH program memory, 512 bytes of SRAM, and 36 bytes of data EEPROM. The -I temperature grade supports an industrial operating range of -40C to +85C. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, RAM, and peripherals into one package. The PIC16 family sits in the hierarchy: PIC16 -> 8-bit PIC microcontrollers -> microcontroller (MCU) -> embedded controller -> semiconductor. The 16F designation indicates FLASH program memory, allowing in-circuit re-programmability. Compared with 32-bit ARM Cortex-M parts, PIC16 devices offer simpler instruction sets, lower cost, and lower power, making them ideal for cost-sensitive sensor and real-time control applications. Key features of the PIC16F15274 include a 10-bit ADC, two PWM modules, two CCP (Capture/Compare/PWM) peripherals, a hardware limit timer (HLT), a windowed watchdog timer (WDT), Peripheral Pin Select (PPS), and communication peripherals including EUSART, SPI, and I2C. It also carries the eXtreme Low-Power (XLP) designation, which allows nanoWatt-style sleep currents suitable for battery-powered sensor nodes. The PIC16F15274 belongs to the PIC16F152xx family of "essential peripheral" devices featuring Core Independent Peripherals (CIPs) such as the hardware limit timer and CWG. These CIPs let the on-chip peripherals operate without CPU intervention, reducing code complexity and improving deterministic real-time response. The 32MHz internal oscillator eliminates the need for an external crystal in many designs, simplifying BOM and reducing PCB area. Typical applications include IoT sensor nodes, home appliances, automotive body electronics, battery-powered metering, LED lighting controllers, and general-purpose embedded control in consumer and industrial products. The wide operating voltage and ultra-low sleep current suit coin-cell and energy-harvesting designs, while the EUSART and SPI/I2C peripherals allow straightforward connection to sensors, EEPROMs, and host MCUs. When designing with this part, leave adequate decoupling (typically 100 nF plus 10 uF bulk) close to VDD, follow Microchip's guidelines for in-circuit serial programming (ICSP) pad access, and verify ADC accuracy against the actual source impedance. Compared with discrete analog designs, the integrated 10-bit ADC and PWM simplify the BOM but require careful PCB grounding for noise-sensitive measurements. This page synthesizes distributor pricing, drop-in package-compatible alternatives drawn from Microchip's PIC16F152xx family, and practical design notes that go beyond the manufacturer datasheet to help engineers select the right variant for cost, pinout, and peripheral needs.

Angebot Kontakt

PIC16F15275-E/MP

PIC16F15275-E/MP - 14KB Flash 8-bit MCU 40-QFN | Microchip

The Microchip Technology PIC16F15275-E/MP is an 8-bit PIC16 microcontroller built around a 32 MHz CPU core with 14 KB of Flash program memory, 1 KB of SRAM, and Peripheral Pin Select (PPS), housed in a 40-pin QFN (5x5 mm) package. The device belongs to the PIC16F152xx family of "full-featured" mid-range microcontrollers that combine Core Independent Peripherals (CIPs) with intelligent analog and standard communication peripherals for cost-sensitive sensor and real-time control applications. Background Knowledge: An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (typically Flash), working RAM, and a mix of peripherals such as ADC, timers, PWM, and serial interfaces. PIC microcontrollers use a modified Harvard RISC architecture with separate program and data buses, which lets the CPU fetch instructions while reading data from RAM in the same cycle. Microcontrollers occupy the semiconductor hierarchy "MCU -> 8-bit microcontroller -> embedded controller -> semiconductor device" and are the dominant processing element in white goods, IoT endpoints, sensor nodes, and industrial control. Key features of the PIC16F15275 include 14 KB (14K x 8) of self-programmable Flash, 1 KB of SRAM, a 10-bit Analog-to-Digital Converter (ADC), two PWM modules, two Capture/Compare/PWM (CCP) peripherals, a hardware limit timer (HLT), a watchdog timer (WDT), PPS for flexible pin mapping, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and both SPI and I2C serial interfaces. The family is engineered for eXtreme Low-Power (XLP) operation, with multiple power-managed modes and a fast wake-up time that suits battery-powered sensor applications. The wide 1.8 V to 5.5 V operating range allows direct connection to 2-cell battery stacks, single-cell Li-ion chemistries, and 5 V industrial rails. The PIC16F15275 uses Microchip's mid-range 8-bit core with a 14-bit instruction word and a 32 MHz internal oscillator, producing roughly 8 MIPS of throughput. The CIPs - including the hardware limit timer, complementary waveform generator, and PPS - let designers replace discrete analog and timing components with on-chip hardware, shrinking board area and BOM cost while improving determinism. The 10-bit ADC, combined with PPS, allows flexible analog front-end design for sensor signal conditioning. Typical applications include low-power IoT sensor nodes, battery-operated environmental monitors, home automation controllers, motor-control front-ends using CCP/PWM, LED lighting controls, white-goods user-interface boards, and small industrial sensor hubs. The 40-QFN footprint is suitable where a compact 5x5 mm area is preferred and the larger pin count of the family must be retained. When designing with this part, ensure that the decoupling capacitor layout follows the datasheet recommendation (typically a 100 nF plus a bulk cap near VDD) and that unused I/O pins are configured as outputs low or inputs with weak pull-ups to minimise sleep current. The PPS feature lets pins be remapped at runtime, but pin-function changes take effect only after a locking sequence; consult the datasheet "PPS" chapter before re-routing peripherals. This page synthesises distributor pricing, drop-in alternatives drawn from the same PIC16F152xx family, and practical design notes not always collected in the manufacturer datasheet.

Angebot Kontakt

PIC16F15275-E/PT

PIC16F15275-E/PT - 8-Bit 32MHz MCU, 14KB Flash, 44-TQFP | Microchip

The Microchip Technology PIC16F15275-E/PT is an 8-bit PIC microcontroller from the PIC16F152xx family delivering 32 MHz CPU performance with 14 KB of Flash program memory, 1 KB of SRAM, and 10-bit ADC capability, housed in a 44-pin TQFP (10x10 mm) package. The device integrates 2x PWM, 2x CCP, Hardware Limit Timer (HLT), Watchdog Timer, Peripheral Pin Select (PPS), EUSART, SPI/I2C, and the eXtreme Low-Power (XLP) feature set, providing a balanced mix of Core Independent Peripherals (CIPs) and communication interfaces for cost-sensitive embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash for program storage, SRAM for runtime data, and EEPROM for non-volatile user data), and configurable peripheral blocks. The PIC16F15275 belongs to Microchip's enhanced mid-range 8-bit PIC architecture, which positions it within the broader taxonomy: microcontroller -> 8-bit MCU -> PIC16 family -> PIC16F152xx sub-family -> semiconductor IC. This hierarchy matters because engineers often select parts by walking up the tree until the right combination of memory, peripherals, and price is reached. Key features of the PIC16F15275 include 14 KB self-programmable Flash (10,000 erase/write cycles typical), 1 KB SRAM, integrated 10-bit ADC with computation, Core Independent Peripherals (CIPs) such as the Hardware Limit Timer and Configurable Logic Cells, and the XLP suite for sub-uA sleep currents. The device operates across the industrial -40C to +125C range and supports in-circuit serial programming (ICSP) for field firmware updates. Architecturally, the PIC16F15275 uses Microchip's enhanced mid-range core with a 16-bit instruction word and a 32 MHz internal oscillator, providing 8 MIPS of throughput. PPS allows flexible mapping of digital peripherals to I/O pins, simplifying PCB layout when signal routing is constrained. The 10-bit ADC with computation accelerates sensor signal conditioning in firmware by handling averaging, oversampling, and threshold comparisons in hardware. Typical applications include industrial sensor nodes, low-power IoT edge devices, appliance control boards, and consumer electronics with HMI or motor control needs. The combination of XLP sleep modes, PWM, and EUSART is well suited to battery-powered measurement and remote-control systems where standby current dominates battery life. When designing with this part, prioritize the PPS pin map early in the schematic phase to avoid pin re-routing late in the design. Place the decoupling network (100 nF plus 1-10 uF bulk) within 5 mm of the VDD pin and tie the MCLR pin through the recommended 10 kohm pull-up, since the XLP modes depend on clean power-rail transitions for predictable wake-up timing. This page consolidates distributor pricing, package-level drop-in alternatives, and practical design notes for the PIC16F15275-E/PT, complementing the manufacturer datasheet with information gain that typical catalog pages do not provide.

Angebot Kontakt

PIC16F15275-I/MP

PIC16F15275-I/MP - 8-Bit MCU, 32MHz, 14KB Flash, 40-QFN | Microchip

The Microchip Technology PIC16F15275-I/MP is an 8-bit PIC16 microcontroller featuring 14KB of Flash program memory, 1KB of RAM, and a 32 MHz CPU delivering 32 MIPS single-cycle throughput, housed in a 40-pin QFN (5x5 mm) package. The device integrates a 10-bit Analog-to-Digital Converter (ADC), two Pulse-Width Modulation (PWM) modules, two Capture/Compare/PWM (CCP) peripherals, Peripheral Pin Select (PPS), EUSART, SPI/I2C, Hardware Limit Timer (HLT), Watchdog Timer (WDT), and eXtreme Low-Power (XLP) technology for battery-friendly operation. An 8-bit microcontroller is a small computing system-on-chip that combines a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a set of digital and analog peripherals on a single silicon die. Within the broader taxonomy, the PIC16F15275 belongs to the PIC16F family of mid-range microcontrollers from Microchip Technology, which sits between the smaller PIC10/12/14 baseline families and the higher-performance PIC18 and PIC32 (32-bit) families. It is classified under the wider category of embedded microcontrollers (MCUs), which are themselves a sub-class of microprocessors and, at the highest level, semiconductors. This position in the hierarchy makes the PIC16F15275 a typical choice for cost-sensitive sensor and real-time control applications where predictable deterministic execution and low power are valued over raw throughput. Key differentiating features include 14KB self-programmable Flash with code protection, 1KB RAM, Core Independent Peripherals (CIPs) that offload timing-critical tasks from the CPU, Intelligent Analog with a 10-bit ADC, and eXtreme Low-Power modes with currents in the microamp range. The PPS module allows flexible reassignment of digital peripheral pins to physical I/O, simplifying PCB layout and reducing routing congestion on dense 40-pin designs. The 32 MHz internal oscillator eliminates the need for an external crystal in many designs, further reducing bill-of-materials cost. Technically, the PIC16F15275 implements a Harvard-architecture RISC CPU with a small, deterministic instruction set optimized for compiled C efficiency. The ADC includes acquisition control and result averaging features, while the PWM modules support complementary outputs and configurable dead-band delays for motor-drive signal generation. The combination of HLT, CCP, and PPS allows the device to service many sensor inputs or closed-loop control tasks in hardware without CPU intervention. Typical applications include IoT sensor nodes, industrial sensor hubs, home appliance control boards, low-power wireless sensor platforms, LED lighting controllers, battery-powered handheld instruments, and automotive body and accessory modules. The wide operating voltage range and XLP sleep currents also suit remote telemetry and energy-harvesting designs. When designing with this part, ensure the chosen supply voltage matches the ADC reference requirement if using the internal reference, and remember that PPS reassignments must be reconfigured after every reset. For sleep-mode designs, verify all wake sources are correctly configured to avoid missed events. This page synthesizes distributor pricing, drop-in compatible alternatives from the PIC16F152 family, and practical design notes not found in the manufacturer datasheet, providing a faster engineering decision than browsing individual component pages.

Angebot Kontakt

PIC16F15275-I/PT

PIC16F15275-I/PT - 8-Bit MCU, 32MHz, 14KB Flash, 44-TQFP | Microchip

The Microchip Technology PIC16F15275-I/PT is an 8-bit PIC microcontroller with a 32 MHz CPU core, 14 KB of Flash program memory and 1 KB of SRAM, housed in a 44-pin TQFP (10x10 mm) industrial-temperature package. It belongs to the PIC16F152xx family and integrates Core Independent Peripherals, 10-bit ADC, two PWM channels, two CCP modules, PPS, EUSART, SPI/I2C, an HLT peripheral, WDT and Microchip's eXtreme Low-Power (XLP) technology. A microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory, working RAM, and a set of on-chip peripherals such as ADC, timers and communication blocks. PIC microcontrollers sit inside the broader hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit. Because the program memory, peripherals and I/O are integrated, an MCU reduces system BOM and PCB area versus a discrete processor plus external peripherals. Key features include operation from 1.8 V to 5.5 V with active currents in the microamp range thanks to XLP, hardware Peripheral Pin Select (PPS) for flexible signal routing, and Core Independent Peripherals that offload timing-critical tasks from the CPU. The 10-bit ADC, two PWM channels and two CCP modules support sensor reading, motor/lighting control and closed-loop feedback, while the integrated EUSART, SPI and I2C cover most wired communication needs. Architecturally the device uses an 8-bit RISC PIC core with single-cycle instruction execution at 32 MHz (8 MIPS for 2T core instructions, equivalent to 32 MIPS peak throughput in single-cycle instructions). The 14 KB Flash is partitioned for self-write support, and the 1 KB SRAM hosts stack, variables and a small RTOS context if needed. PPS allows remapping of digital peripherals to a wide range of I/O pins, simplifying PCB layout. Typical applications include industrial sensing nodes, low-power IoT battery sensors, consumer appliance control, automotive interior lighting and body controllers, small motor control, LED drivers and general-purpose embedded control. The industrial -40C to +85C temperature range suits factory, home and outdoor enclosures. When designing with this part, route PPS-mapped signals early in the schematic phase so the layout does not need rework, and budget the internal oscillator accuracy against your serial-communication baud-rate error budget. Provide a 0.1 uF + 1 uF bulk decoupling network on VDD/AVDD pairs. This page synthesizes distributor pricing, drop-in alternative inventory and practical design notes not found in the manufacturer datasheet alone, giving the engineer a single place to evaluate PIC16F15275-I/PT fit for an embedded design.

Angebot Kontakt

PIC16F15276-E/MP

PIC16F15276-E/MP - 28KB Flash 8-bit MCU, 40-QFN | Microchip

The Microchip Technology PIC16F15276-E/MP is an 8-bit PIC microcontroller built around the PIC16F152xx family architecture, delivering 28KB of Flash program memory, 2KB of RAM, and a 32MHz internal core speed in a 40-pin QFN (5x5 mm) package with exposed pad. It belongs to the eXtreme Low-Power (XLP) family and integrates Core Independent Peripherals (CIPs) for sensor and real-time control applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, volatile data memory (RAM), and peripherals such as timers, ADCs, and communication interfaces. PIC microcontrollers from Microchip use a Harvard RISC architecture with separate program and data buses, delivering deterministic instruction execution in a single cycle for many instructions. The PIC16F15276 sits in the mid-range of the PIC16F1xxx family, balancing program memory density with low-power operation and modern peripherals. Key features of this device include a 10-bit ADC with computation, two PWM modules, two CCP (Capture/Compare/PWM) modules, an EUSART plus SPI and I2C communications, hardware Limit Timer (HLT), Windowed Watchdog Timer (WDT), Peripheral Pin Select (PPS), and the XLP nanoWatt technology for battery-powered designs. The 32MHz internal oscillator supports instruction rates up to 8 MIPS, while multiple low-power sleep modes (Doze, Idle, Sleep) and nanoWatt XLP enable quiescent currents in the microampere range. Architecturally, the PIC16F15276 uses a 14-bit instruction word RISC core with hardware multiplier, vectored interrupts, and an interrupt-driven peripheral set including Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and Numerically Controlled Oscillator (NCO) - features normally found on higher-pin-count devices but made available in this 40-pin QFN through careful pin multiplexing. The PPS system remaps peripheral signals to most I/O pins, simplifying PCB layout. Typical applications include low-cost sensor nodes, IoT edge devices, home appliance control, LED lighting controllers, small motor control loops, battery-powered instrumentation, and general-purpose embedded control. The combination of low power, ample memory, and standard communication peripherals makes it well suited to cost-sensitive designs that previously required larger or more expensive MCUs. When designing with this part, ensure the 40-QFN exposed pad is soldered to a sufficiently large copper thermal plane on the PCB to meet the thermal resistance (theta-JA) specification in the datasheet. Use the MPLAB X IDE and XC8 compiler for firmware development, and consider the PPS configuration very early in the schematic design to avoid pinout rework. This page consolidates distributor pricing, drop-in same-package alternatives, application examples, and design considerations not found in the manufacturer datasheet alone. Engineers can use the comparison table to evaluate same-footprint variants within the PIC16F152xx family and the cross-references to plan second-source supply.

Angebot Kontakt

PIC16F15276-E/PT

PIC16F15276-E/PT - 32MHz 8-bit MCU, 28KB Flash | Microchip

The Microchip Technology PIC16F15276-E/PT is a 32MHz 8-bit PIC microcontroller featuring 28KB of Flash program memory, 2KB of SRAM, and 28 channels of 10-bit ADC, housed in a 44-pin TQFP (10x10 mm) package. It integrates eXtreme Low-Power (XLP) technology with core-independent peripherals (CIPs), making it suitable for cost-sensitive sensor and real-time control applications. The 'E' suffix designates the extended (-40C to +125C) operating temperature range. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory, data memory, and integrated peripherals such as ADCs, timers, and communication interfaces. The PIC16F15276 belongs to Microchip's PIC16 mid-range 8-bit MCU family, which sits between the PIC10/12/16 baseline series and the PIC18 enhanced series in the company's taxonomy. Within the power-management hierarchy, this device performs digital control of sensors and actuators rather than power conversion itself. Key features include 32MHz maximum CPU clock (8 MIPS instruction throughput), 28KB Flash self-programmable program memory, 2KB data SRAM, 10-bit ADC with up to 28 input channels, two 10-bit PWMs, two CCP modules, and standard serial interfaces including EUSART, SPI, and I2C. Peripheral Pin Select (PPS) allows flexible signal routing, and the Hardware Limit Timer (HLT) simplifies safety-critical timing. The PIC16F15276 architecture uses a Harvard RISC core with single-cycle instructions, achieving deterministic 125ns instruction execution at 32MHz. Intelligent Analog peripherals operate without CPU intervention, reducing software complexity. The XLP technology delivers nanoWatt sleep currents, enabling battery-powered applications with multi-year lifetimes. Typical applications include industrial sensor interfaces, IoT edge nodes, building automation, low-power wireless sensor hubs, home appliance control, and battery-powered measurement instruments. The 10-bit ADC and PWM channels simplify motor and lighting control loops. Designers should consider the device's 1.8V to 5.5V supply range when integrating with sensors or 3.3V/5V logic. PPS flexibility requires careful pin-map planning in MPLAB X IDE to avoid signal conflicts, and the -E temperature grade suits automotive under-hood and industrial environments. This page synthesizes distributor pricing, drop-in alternatives from Microchip's PIC16F152xx family, and design considerations not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC16F15276-I/PT

PIC16F15276-I/PT - 28KB Flash 8-bit MCU, 32MHz, 44-TQFP | Microchip

The Microchip Technology PIC16F15276-I/PT is a 28KB Flash 8-bit PIC microcontroller built on an enhanced mid-range RISC core with a 32 MHz maximum CPU clock, housed in a 44-pin TQFP (10x10 mm) package. It integrates 28KB of Flash program memory, 2KB of SRAM, hardware Core Independent Peripherals (CIPs), Intelligent Analog, and standard communication peripherals for cost-sensitive sensor and real-time control designs. An 8-bit PIC microcontroller is a single-chip CMOS device that combines an 8-bit CPU core, Flash program memory, SRAM, and on-chip peripherals in one package. The PIC16F152xx family occupies a specific tier in the Microchip hierarchy: 8-bit microcontroller -> PIC16 mid-range family -> PIC16F152xx sub-family -> eXtreme Low-Power (XLP) lineup. Its role in a system is to provide deterministic real-time control and sensor I/O with low active and sleep currents, sitting below 16-bit dsPIC and 32-bit SAM devices in computational capability but above simple timer/logic ICs in integration. Key features include 32 MHz maximum operation, 1.8V minimum supply for full-speed analog operation at 16 MHz, hardware 10-bit ADC, two PWM modules, two CCP modules, EUSART, SPI, I2C, Peripheral Pin Select (PPS), Hardware Limit Timer (HLT), Watchdog Timer, and XLP eXtreme Low-Power modes. The 36 programmable I/O lines and 44-pin TQFP footprint make this device well suited to mid-density IoT nodes, sensor hubs, and small industrial control boards. The architecture uses Microchip's enhanced mid-range core with a 16-level hardware stack and a 31-level software-managed stack extension. The integrated 10-bit ADC with internal reference, op amps, and comparators deliver Intelligent Analog, while CIPs such as the CWG (Complementary Waveform Generator) and HLT offload timing-critical functions from the CPU for deterministic, low-jitter response. Typical applications include low-power IoT sensor nodes, battery-powered remote controls, industrial sensor signal conditioning, home appliances, lighting control, and small motor/PWM control. The XLP nanoWatt sleep modes and 1.8V minimum supply make it especially attractive for energy-harvesting designs that must wake, sample, transmit, and return to deep sleep. When designing with this part, place decoupling capacitors within 3 mm of each VDD pin and keep analog traces short and guarded for ADC accuracy. PPS allows pin reassignment after PCB layout is complete, reducing iteration cost during hardware bring-up. This page synthesizes distributor pricing, drop-in alternatives drawn from the PIC16F152xx/153xx family, and practical design notes not collected in a single section of the manufacturer datasheet.

Angebot Kontakt

PIC16F1527T-I/PT

PIC16F1527T-I/PT - 8-bit 20MHz MCU 28KB Flash 64-TQFP | Microchip

The Microchip Technology PIC16F1527T-I/PT is an 8-bit PIC16 family microcontroller built on Microchip's enhanced mid-range core, delivering 20 MHz CPU performance (200 ns instruction cycle) with 28 KB of self-programmable Flash program memory and 1.5 KB of SRAM in a 64-pin TQFP (PT) package supplied on tape and reel. Headline parameters include 28 KB Flash (16K x 14 words), 1.5 KB RAM, 256 B EEPROM, 20 MHz maximum clock, and a 1.8 V to 5.5 V wide operating voltage range. The device belongs to the PIC16F152x family which integrates 12-bit ADC, multiple timers, EUSART, MSSP (SPI/I2C) peripherals, and Microchip's nanoWatt XLP ultra-low-power technology. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, peripherals and I/O on one die. Within the semiconductor taxonomy, an MCU sits under microcontroller -> embedded processor -> integrated circuit -> semiconductor. The '8-bit' designation refers to the native data bus width; PIC16 MCUs use a modified Harvard RISC architecture with separate program and data buses, which accelerates instruction fetch and allows single-cycle execution for most instructions. This family is widely used in cost-sensitive, low-power embedded designs where deterministic real-time behaviour matters more than raw throughput. Key features of the PIC16F1527T-I/PT include 28 KB Flash with self-programmability, 1.5 KB SRAM, 256 B EEPROM, a 12-bit differential ADC with computed channels, up to 54 digital I/O pins, four 8-bit timers plus two CCP and one ECCP module, two EUSART, two MSSP (SPI/I2C), an integrated temperature indicator, and nanoWatt XLP sleep currents below 1 uA. The 64-TQFP package measures 10 x 10 mm with a 0.5 mm lead pitch. Architecturally, the PIC16F1527T-I/PT uses a 14-bit instruction word and a 16-level hardware stack, with an interrupt controller supporting both core and peripheral interrupt sources. The 12-bit ADC is supported by a dedicated FVR (Fixed Voltage Reference) and a DAC, enabling ratiometric measurements and on-chip analogue signal conditioning without external components. Typical applications include consumer appliance control, sensor interface modules, battery-powered handheld instruments, simple motor and lighting controllers, and industrial sensor hubs. The wide 1.8-5.5 V supply range allows direct operation from 2xAA/AAA cells or 3.3 V/5 V regulated rails. When designing with this MCU, confirm that the application's interrupt latency budget is compatible with the 20 MHz core; pin remapping is limited and I/O assignments should be planned during PCB layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC16F15313-E/RF

PIC16F15313-E/RF - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

The Microchip Technology PIC16F15313-E/RF is an 8-bit PIC microcontroller from the PIC16F15313 family featuring the enhanced mid-range core running at up to 32 MHz, with 3.5 KB (2K x 14) of self-read/write Flash program memory, 256 bytes of RAM, and packaged in an 8-pin UDFN (3x3 mm) with exposed pad (RF suffix). The part carries the E (extended) temperature grade and is part of Microchip's eXtreme Low Power (XLP) family, designed for battery-powered and energy-harvesting applications. An 8-bit microcontroller (MCU) is a compact processor integrating CPU, Flash, RAM, and peripherals on a single die. Within the broader taxonomy, the PIC16F15313-E/RF sits in the hierarchy: 8-bit MCU -> PIC16 family -> enhanced mid-range core -> PIC16F153xx sub-family -> eXtreme Low Power (XLP) series -> embedded microcontroller. Its 49-instruction set and 16-level stack make it code-compatible with the wider PIC16F1xxx family, allowing easy migration and tool reuse with MPLAB X IDE and the XC8 compiler. Key features include 4x 10-bit PWMs, a 10-bit ADC with computation, a 5-bit DAC, comparators, 4x Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), an EUSART, and SPI/I2C interfaces. Peripheral Pin Select (PPS) remaps digital peripherals to any I/O pin, simplifying PCB routing on this small 8-pin package. The XLP features IDLE and DOZE low-power modes plus Peripheral Module Disable (PMD) to switch off unused peripherals, achieving nanoWatt sleep currents. Typical applications include wireless charging control loops (replacing ASIC-based solutions), IoT sensor nodes, low-cost consumer electronics, LED lighting controllers, and battery-powered remote controls. The small 3x3 mm UDFN footprint suits space-constrained wearables and portable medical accessories. When designing with this MCU, leverage Peripheral Pin Select to free PCB routing from the strict pin-per-peripheral mapping of older PICs. Use PMD aggressively in sleep loops to drop quiescent current below 1 uA, and verify the UDFN exposed pad is properly soldered for thermal dissipation and electrical ground. This page synthesizes distributor pricing, drop-in alternative MPNs, comparison tables, and practical design notes not found in the manufacturer datasheet, giving engineers and procurement a single reference for the PIC16F15313-E/RF.

Angebot Kontakt

PIC16F15313-E/SN

PIC16F15313-E/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F15313-E/SN is an 8-bit PIC16F microcontroller (MCU) featuring 3.5KB (2K x 14) of Flash program memory, 256 bytes of RAM, and a 32MHz internal oscillator, housed in an 8-pin SOIC package. It belongs to the PIC16F15313 family of "full-featured" low-pin-count MCUs and operates from 2.3V to 5.5V across the extended industrial temperature range (-40C to +125C). An 8-bit microcontroller (MCU) is a small, low-power computer-on-a-chip that integrates a CPU, memory, and programmable I/O on a single die; the PIC16F15313-E/SN sits within the PIC16 family -> PIC16F1xxx enhanced mid-range -> 8-bit PIC microcontroller -> embedded MCU hierarchy. By integrating peripherals such as a DAC, ADC, comparators, PWM, CLC (Configurable Logic Cell), CWG (Complementary Waveform Generator), and EUSART/SPI/I2C, it eliminates many external components that designers previously had to add separately. Key features include 4xPWMs, 4x Configurable Logic Cells (CLC), 1x 5-bit DAC, 1x 10-bit ADC, 2x comparators with selectable references, a Complementary Waveform Generator (CWG), and EUSART with auto-baud detect. The device also supports SPI and I2C peripherals for sensor and display interfacing, plus eXtreme Low Power (XLP) technology for ultra-low sleep currents in battery-powered applications. The PIC16F15313-E/SN uses Microchip's enhanced mid-range 8-bit core, providing a single-cycle instruction set and 49 instruction types for efficient code density. Internal voltage regulation and a wide operating voltage range (2.3V to 5.5V) enable direct Li-ion, 3.3V, or 5V system operation without external regulators. The CLC blocks allow glue-logic replacement directly inside the MCU, reducing PCB complexity and BOM cost. Typical applications include Qi 1.1 5W wireless charging controllers, IoT sensor nodes, LED lighting controllers, small consumer appliances, battery-powered toys, fan and pump controllers, and general-purpose logic-replacement boards where a compact 8-pin footprint is required. When designing with this device, prioritize pin allocation early because the 8-pin SOIC exposes only 6 usable I/O pins. Use the MPLAB X IDE with MPLAB XC8 compiler and consider migrating legacy PIC10/12/16 code to the unified PIC16F1xxx platform to maximize code reuse. Add a 0.1uF decoupling capacitor within 5mm of VDD for stable operation.

Angebot Kontakt

PIC16F15313-E/SNVAO

PIC16F15313-E/SNVAO - 8-bit MCU, 3.5KB Flash, 32MHz, AEC-Q100 | Microchip

The Microchip Technology PIC16F15313-E/SNVAO is an automotive-grade, full-featured 8-bit PIC16 microcontroller built on an enhanced mid-range core with 49 instructions and 16 stack levels, delivering 32 MHz CPU performance from a 2.3 V to 5.5 V supply. The device integrates 3.5 KB (2K x 14) of self read/write Flash program memory, 256 bytes of RAM, 4x 10-bit PWMs, a 5-channel 10-bit ADC, a 5-bit DAC, two comparators, a Complementary Waveform Generator (CWG), EUSART, and SPI/I2C peripherals, all in a compact 8-pin SOIC package. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral I/O on one die. Within the broader taxonomy, the PIC16F15313 belongs to the 8-bit MCU class, sits inside the PIC16 family of mid-range cores, and ships with Core Independent Peripherals (CIPs) that operate without CPU intervention, freeing the core for power-saving tasks. eXtreme Low Power (XLP) features such as IDLE and DOZE modes, plus Peripheral Module Disable (PMD), make the device especially attractive for battery-powered or energy-harvesting designs. Key differentiating features include the Memory Access Partition (MAP) for bootloader-style code protection, Peripheral Pin Select (PPS) for flexible signal routing, and an internal temperature indicator. The "VAO" suffix and operating range of -40 °C to +125 °C confirm AEC-Q100 automotive qualification, distinguishing this variant from the industrial-grade PIC16F15313-I/SN. The 8-SOIC footprint (3.90 mm body width) eases hand-soldering and visual inspection while remaining compatible with high-volume SMT lines. Architecturally, the enhanced mid-range core executes most instructions in one instruction cycle and supports interrupt-driven CIPs, allowing deterministic response times without software polling. The integrated 5-bit DAC and rail-to-rail comparators enable closed-loop analog control without external components, reducing BOM cost and PCB area in sensor-interface, lighting-control, and consumer appliance designs. Designers migrating from older PIC10/12/16F parts benefit from code compatibility through the standard instruction set. Typical applications include automotive body controllers, sensor signal conditioning, low-power IoT edge nodes, LED lighting control loops, and consumer remote-control transmitters. The combination of CIPs, PPS, and XLP modes also makes the part a strong fit for sealed-housing applications where post-assembly firmware updates via the self-write Flash minimize mechanical access requirements. When designing with this device, allocate the brown-out and watchdog timer configuration early, because changing these settings late in the development cycle can compromise functional safety arguments in automotive programs. Use the MAP feature to lock the bootloader region from accidental overwrite by the application image.

Angebot Kontakt

PIC16F15313-I/P

PIC16F15313-I/P - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip

The Microchip Technology PIC16F15313-I/P is an 8-bit PIC RISC microcontroller with 3.5KB Flash, 256B RAM, and 32MHz operation, housed in an 8-pin PDIP through-hole package. It operates from 2.3V to 5.5V and features eXtreme Low-Power (XLP) technology, 4 PWMs, comparator, ADC, 5-bit DAC, 4x Configurable Logic Cells (CLC), CWG, EUSART, and SPI/I2C peripherals. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and programmable I/O peripherals on one die. The PIC16F15313 belongs to the PIC16 family of 8-bit RISC microcontrollers, which fall within the broader category of embedded processors and microcontrollers, themselves a subset of semiconductor ICs used for system control and signal processing tasks in nearly every electronic product. Key features include 3.5KB self-programmable Flash program memory, 256B SRAM, 4 PWMs with complementary outputs, a 10-bit ADC with computation, a 5-bit DAC, comparator, and 4 Configurable Logic Cells that implement custom logic gates and state machines without external components. The 32MHz internal oscillator and XLP technology support sleep currents as low as 30 nA typical, enabling battery-powered designs. The PIC16F15313 uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction set and hardware Multiply, peripheral pin select (PPS) for flexible signal routing, and on-board debugging via MPLAB ICD. Its integration of CIPs (Core Independent Peripherals) means many functions like waveform generation, signal conditioning, and timing run autonomously without CPU intervention, freeing the core for application logic. Typical applications include IoT sensor nodes, low-power wireless charging controllers (Qi 1.1 5W reference), battery-powered home automation, LED lighting controls, and general-purpose consumer product control. With only 6 I/O pins in the 8-pin PDIP, the device targets compact designs where software-defined peripheral functions (CLC, CWG, NCO) replace external glue logic. When designing with this device, ensure the ICSP programming pins (ICSPCLK/ICSPDAT) are accessible for in-circuit programming and that the MCLR pin has a proper pull-up circuit. Use the PPS feature carefully because re-routing pins may conflict with peripheral functions, and always check that the chosen clock mode provides adequate timing margin for the application. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers a complete commercial and engineering view of the PIC16F15313-I/P.

Angebot Kontakt

PIC16F15313-I/RF

PIC16F15313-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC16F15313-I/RF is an 8-bit PIC® XLP™ 16F-series microcontroller featuring 3.5 KB (2K x 14) of FLASH program memory, 256 bytes of RAM, and a maximum CPU clock speed of 32 MHz, housed in an 8-pin DFN (3x3 mm) package with exposed thermal pad. A microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory (typically FLASH), volatile working memory (RAM), and a rich set of on-chip peripherals such as timers, ADCs, communication interfaces, and configurable logic. MCUs sit at the top of the embedded-computing hierarchy - more capable than a simple ASIC for fixed logic, less expensive than a microprocessor/MPU that requires external RAM and storage, and indispensable for almost every modern electronic product. The PIC16F15313 specifically belongs to Microchip's enhanced mid-range 8-bit family (PIC16), which adds richer peripheral integration and lower power consumption than legacy baseline PIC10/12/16 parts. Key features include 4 PWM channels, an on-chip comparator, a 5-bit DAC, a 10-bit ADC with multiple channels, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), and both EUSART and SPI/I2C serial interfaces. The XLP (eXtreme Low Power) designation brings sub-uA sleep currents, making this part attractive for battery-powered or energy-harvesting designs. Industrial-grade operating temperature range is -40C to +85C, and supply voltage spans 2.3V (at 16 MHz) to 5.5V. Architecturally the PIC16F15313 uses an enhanced mid-range 8-bit RISC core with a hardware multiplier, providing deterministic instruction execution and a single-cycle 8x8 multiply. The device integrates Core Independent Peripherals (CIPs) - CLC, CWG, NCO, and PWM - that operate without CPU intervention, offloading timing-critical functions and reducing firmware complexity while lowering overall system power. Typical applications include IoT sensor nodes, low-cost consumer appliances, white goods control boards, battery-powered wireless charging controllers, LED lighting effects, and general-purpose 8-bit embedded logic replacement. Designers choose it when cost, small footprint, and ultra-low standby power outweigh the need for higher MIPS. When laying out the PCB, follow Microchip's DFN-8 land-pattern recommendation and provide a thermal pad soldered to a copper pour for best thermal performance. Decoupling VDD with a 100 nF ceramic capacitor placed within 2 mm of the pin is recommended for ADC accuracy at higher sampling rates. This page synthesizes Microchip datasheet parameters, current distributor pricing, drop-in same-package alternatives, and practical design notes not found in the datasheet alone - giving engineers a one-stop reference for evaluating the PIC16F15313-I/RF against the PIC16F15313 family and competitor parts.

Angebot Kontakt

PIC16F15313-I/SN

PIC16F15313-I/SN - 8-Bit 32MHz MCU, 3.5KB Flash | Microchip

The Microchip Technology PIC16F15313-I/SN is an 8-bit PIC16F microcontroller with eXtreme Low-Power (XLP) technology, 32 MHz CPU speed, 3.5 KB Flash program memory, 256 B SRAM, and 6 I/O pins, housed in an 8-pin SOIC (SN) package. According to the Microchip PIC16F15313 datasheet, the device integrates Intelligent Analog peripherals (10-bit ADC, 5/8-bit DAC, comparators), Core Independent Peripherals (CIPs) such as four Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and communication peripherals (EUSART, SPI, I2C). An 8-bit microcontroller is a single-chip computer that processes data 8 bits at a time, executing instructions from on-chip Flash program memory and operating on registers and SRAM. PIC microcontrollers use a RISC-based Harvard architecture (separate program and data buses), positioning them under the broader hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. The 8-bit segment remains the workhorse of cost-sensitive, low-power consumer and industrial designs because of deterministic interrupt response, ease of programming in C or assembly, and the rich ecosystem of MPLAB X development tools. The PIC16F15313's key differentiating features include four 10-bit PWM outputs with independent timers, four Configurable Logic Cells that implement custom Boolean functions without CPU intervention, and a Complementary Waveform Generator for half-bridge and full-bridge drive. The device supports 1.8V-5.5V operation and features nanoWatt XLP sleep currents in the sub-100 nA range, enabling battery-powered designs that run for years on a single cell. Architecturally, the PIC16F15313 family uses a 14-bit instruction word and a 32 MHz internal oscillator, allowing software execution at 8 MIPS. The device integrates a power-on reset, brown-out reset, and low-voltage programming, eliminating external supervisory components. The 256 B SRAM and 3.5 KB Flash are sufficient for state machines, sensor processing, and small protocol stacks. Typical applications include battery-operated sensor nodes, IoT edge devices, consumer remote controls, LED lighting controllers, low-end motor control loops, and Qi 1.1 wireless-charging transmitter controllers. The 8-pin footprint makes it one of the smallest PIC16F devices available, allowing drop-in use in space-constrained products. When designing with the PIC16F15313-I/SN, ensure the ICSPDAT/ICSPCLK pin sharing is managed and that the MCLR pull-up is correctly configured for in-circuit serial programming. The four PWM channels are useful for driving LEDs or brushed DC motors without external timers. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and BOM decisions.

Angebot Kontakt

Unterkategorien

Produkte (38.000+)

PIC16F1526-I/MR - 8-Bit 20MHz 14KB Flash 64-QFN MCU | Microchip

PIC16F1526T-I/PT - 8-bit PIC MCU 14KB Flash 20MHz | Microchip

PIC16F1527-E/PT - 8-bit 20MHz 28KB Flash MCU | Microchip 64-TQFP

PIC16F1527-I/PT - 8-Bit 20MHz 28KB Flash MCU | Microchip

PIC16F15274-E/MP - 8-Bit MCU, 32MHz, 7KB Flash, 40-QFN | Microchip

PIC16F15274-E/P - 8-bit 32MHz MCU, 7KB Flash 40-PDIP | Microchip

PIC16F15274-E/PT - 8-bit MCU, 7KB Flash, 32MHz, 44-TQFP | Microchip

PIC16F15274-I/MP - 8-Bit 32MHz 7KB Flash MCU | Microchip | QFN-40

PIC16F15274-I/P - 7KB Flash 8-bit MCU, 32MHz, 40-PDIP | Microchip

PIC16F15274-I/PT - 8-bit 32MHz MCU 7KB FLASH TQFP-44 | Microchip

PIC16F15275-E/MP - 14KB Flash 8-bit MCU 40-QFN | Microchip

PIC16F15275-E/PT - 8-Bit 32MHz MCU, 14KB Flash, 44-TQFP | Microchip

PIC16F15275-I/MP - 8-Bit MCU, 32MHz, 14KB Flash, 40-QFN | Microchip

PIC16F15275-I/PT - 8-Bit MCU, 32MHz, 14KB Flash, 44-TQFP | Microchip

PIC16F15276-E/MP - 28KB Flash 8-bit MCU, 40-QFN | Microchip

PIC16F15276-E/PT - 32MHz 8-bit MCU, 28KB Flash | Microchip

PIC16F15276-I/PT - 28KB Flash 8-bit MCU, 32MHz, 44-TQFP | Microchip

PIC16F1527T-I/PT - 8-bit 20MHz MCU 28KB Flash 64-TQFP | Microchip

PIC16F15313-E/RF - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

PIC16F15313-E/SN - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15313-E/SNVAO - 8-bit MCU, 3.5KB Flash, 32MHz, AEC-Q100 | Microchip

PIC16F15313-I/P - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip

PIC16F15313-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC16F15313-I/SN - 8-Bit 32MHz MCU, 3.5KB Flash | Microchip