Integrierte Schaltungen

PIC24FJ256GB606T-I/MR

PIC24FJ256GB606T-I/MR - 16-Bit 32MHz USB MCU 256KB Flash | Microchip

The Microchip Technology PIC24FJ256GB606T-I/MR is a 16-bit RISC microcontroller from the PIC® 24F family, integrating a 32MHz PIC24 core, 256KB (85.5K x 24) of dual-partition Flash program memory, and 32KB of SRAM in a 64-pin QFN (9x9 mm) package with exposed thermal pad. The device provides up to 53 general-purpose I/O lines, integrates USB 2.0 Full-Speed with on-chip transceiver and physical layer, and supports Live Update firmware swap between Flash partitions for fail-safe field upgrades. A 16-bit microcontroller (MCU) is a single-chip computer whose data path and arithmetic logic unit operate on 16-bit words, sitting hierarchically between 8-bit MCUs (e.g., PIC16, AVR) and 32-bit MCUs (e.g., PIC32, ARM Cortex-M). The PIC24F family uses a modified Harvard architecture with a 16-bit instruction word and 24-bit fixed instruction length, offering higher code density than typical 16-bit MCUs and a rich peripheral set for mixed-signal embedded designs. Key differentiating features include 7 timers, 6 PWM channels, 3 analog comparators, 8 DMA channels, 6 UART modules, 3 SPI interfaces, 3 I2C interfaces, a 16-channel 10-bit ADC, an RTCC with calendar mode, and the previously mentioned integrated USB 2.0 Full-Speed OTG controller with on-chip transceiver. The dual-partition Flash architecture combined with Live Update makes the part uniquely suited for in-field firmware updates without service interruption. The device operates from 2.0V to 3.6V, supports industrial temperatures of -40C to +85C, and is qualified to Microchip's standard commercial/industrial reliability flow. The USB peripheral, dual-partition Flash, and large SRAM are the architecture's three pillars; together they enable battery-powered or bus-powered designs that must communicate with a host, store telemetry, and survive long deployment in the field. Typical applications include USB HID peripherals, battery-powered medical/fitness devices, portable data loggers, industrial sensor nodes, and consumer accessories. The wide GPIO count and abundant DMA channels let designers attach displays, sensors, and communication stacks without external logic. When designing with this part, allocate the dual-partition Flash wisely so that each partition can hold the full firmware image plus a small bootloader; this is what enables Live Update. Decoupling must include 100nF on every VDD/VSS pair close to the MCU, plus a 4.7uF bulk capacitor on the main rail to handle USB inrush current. This page synthesizes distributor pricing, pin-compatible same-family alternatives, application-specific design notes, and a parameter comparison table that are not present in the manufacturer datasheet alone.

Angebot Kontakt

PIC24FJ256GB606T-I/PT

PIC24FJ256GB606T-I/PT - 16-Bit MCU 256KB Flash USB 64-TQFP | Microchip

The Microchip PIC24FJ256GB606T-I/PT is a 16-bit PIC24F microcontroller featuring a 32 MHz MIPS core, 256 KB of dual-partition Flash program memory (Live Update capable), and 32 KB of SRAM, housed in a 64-pin TQFP (10x10 mm) package. It integrates a full-speed USB 2.0 interface (device/host/OTG), a 16-bit Parallel Master Port (PMP), and a rich peripheral set aimed at connected embedded designs. A microcontroller (MCU) is a single-chip computer integrating a CPU, memory (Flash/RAM), and programmable peripherals. The PIC24F family belongs to the 16-bit MCU hierarchy and sits between 8-bit PIC MCUs and 32-bit ARM Cortex-M devices, offering higher code density and richer peripherals while retaining low-power operation (<100 nA standby current per Microchip). MCUs form the control core of embedded systems across industrial, medical, and consumer products. Key features include 256 KB Flash (85.5K x 24 words) with dual-partition Live Update, 32 KB SRAM, USB 2.0 FS with OTG, integrated peripherals (I2C, SPI, UART, PMP), a 16-channel 12-bit ADC, and configurable low-power Sleep/Idle modes. The part is specified over the -40C to +85C industrial temperature range and ships in tape-and-reel packaging for high-volume surface-mount assembly. The PIC24FJ256GB606 architecture combines a Harvard bus structure, a hardware multiply/divide unit, and DMA into a single low-power core. Dual-partition Flash enables in-field firmware upgrades without downtime — one partition runs while the other updates — critical for industrial and medical devices requiring continuous availability. Typical applications include USB peripherals (HID, CDC, mass storage), portable medical/fitness monitors, industrial control and human-machine interface (HMI) panels, low-power IoT sensor nodes with USB diagnostics, and USB-enabled battery chargers. The Live Update feature makes it especially attractive for always-on products that must accept firmware updates safely. When designing with this device, plan the PCB layout around the 64-pin TQFP with USB trace impedance controlled to 90 ohms differential. Use the dual-partition Flash for failsafe OTA updates, and verify the SRAM allocation (32 KB) against your largest buffer need at compile time. This page synthesizes distributor pricing, drop-in Microchip alternatives, and practical USB/MCU design notes not found in the standalone manufacturer datasheet.

Angebot Kontakt

PIC24FJ256GB610-E/BG

PIC24FJ256GB610-E/BG - 16-Bit 32MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC24FJ256GB610-E/BG is a 16-bit PIC24F microcontroller delivering up to 32 MIPS throughput from a 32 MHz CPU core, packaged in a 121-pin TFBGA (10x10 mm) with 0.80 mm terminal pitch. It integrates 256 KB (85.5K x 24) of dual-partition Flash with ECC and Live Update capability, plus 32 KB of RAM, and is targeted at automotive and industrial USB-OTG designs. The -E suffix denotes the -40C to +125C extended operating temperature range. What is a PIC24F microcontroller? The PIC24F is Microchip's 16-bit MCU family built on a modified Harvard architecture with a 16-bit datapath and 24-bit instruction word, sitting between 8-bit PIC16/PIC18 MCUs and 32-bit PIC32 devices. It targets low-power (eXtreme Low Power, XLP) and USB-enabled embedded applications, balancing deterministic interrupt latency with rich connectivity (USB OTG, UART, SPI, I2C) - a category typically used in consumer, industrial, and automotive body-electronics designs. Key features include six UART modules, three I2C and three SPI interfaces, six PWM channels with capture/compare, a 10-bit 1.1 Msps ADC, a Real-Time Clock/Calendar, and a full-speed USB 2.0 On-The-Go controller with PHY. The dual-bank Flash with ECC and Live Update allows field firmware upgrades without downtime, a critical feature for remote sensors and automotive modules requiring in-service reprogramming. Architecturally, the device combines a single-cycle 16-bit ALU with a hardware multiply/divide engine and a DMA-free peripheral set. The XLP deep-sleep current (typical values vary by mode) supports years of battery life when paired with an external RTC and sleep-wake peripheral triggers, while the 85 GPIO pins and extensive interrupt-on-change logic enable complex human-machine interface and sensor-fusion front-ends. Typical applications include USB-OTG peripherals, automotive body controllers, industrial HMI panels, smart energy metering, and portable medical instrumentation. The wide extended temperature range and AEC-Q100 qualification suitability make the PIC24FJ256GB610 family attractive for under-hood automotive nodes and outdoor industrial installations. When designing with this MCU, allocate the 0.80 mm BGA ball pitch carefully - it requires HDI PCB fabrication (laser-drilled microvias) and precise reflow profiling. The Live Update feature must be enabled in the configuration words and requires the dual-partition linker script; firmware teams should plan application layout for safe A/B image swap before deployment.

Angebot Kontakt

PIC24FJ256GB610-E/PT

PIC24FJ256GB610-E/PT - 16-bit 32MHz 256KB Flash USB MCU | Microchip

The Microchip Technology PIC24FJ256GB610-E/PT is a 16-bit PIC24F microcontroller with 256 KB Flash, 32 KB RAM, USB 2.0 OTG, and 85 I/O pins operating at 32 MHz, housed in a 100-pin TQFP (12x12 mm) package. It combines the eXtreme Low Power (XLP) technology with dual-partition Flash supporting Live Update, Error Correction Code (ECC), and a full-speed USB 2.0 On-The-Go controller for embedded designs requiring wired connectivity and field-upgradeable firmware. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals (timers, ADCs, communication controllers, GPIO), and sometimes connectivity interfaces like USB or CAN. The PIC24F family sits in Microchip's 16-bit tier, balancing cost, deterministic performance, and low power consumption for consumer, industrial, and automotive edge-node designs. Within the system hierarchy: microcontroller -> 16-bit MCU -> embedded processor -> semiconductor IC -> integrated circuit. The 'F' suffix denotes Flash-based program memory; 'J' designates the 3.3 V eXtreme Low Power family. Key features include 256 KB (85.5K x 24) Flash with ECC and dual partition support, 32 KB RAM, hardware crypto engine (AES, DES, MD5, SHA-1/2), 32 MHz operation with 16 MIPS throughput, CTMU for up to 64 touch buttons, and 85 remappable I/O via Peripheral Pin Select (PPS). AEC-Q100 qualification, an automotive-grade temperature range of -40C to +125C, and 2.0 V to 3.6 V single-supply operation round out its envelope. Architecturally, the PIC24FJ256GB610 uses a 16-bit modified Harvard core with separate program and data buses, JTAG/programming/debug (Trace SWD/ICSP), and integrated analog (10/12-bit ADC), digital (timers, capture, PWM), and connectivity (USB OTG, SPI, I2C, UART) peripherals. PPS allows most digital I/O to be remapped to alternate pins, simplifying PCB routing in dense designs. Typical applications include USB-enabled embedded nodes (human-interface devices, mass-storage bridges), low-power sensor hubs with touch input, automotive body and HMI controllers, industrial HMI panels, and edge IoT devices requiring firmware-over-the-air updates via the dual-partition Live Update Flash. When designing, allocate separate decoupling caps on VDD/VSS pairs, route the 48 MHz USB clock trace with 90-ohm controlled impedance, and use the PPS registers carefully - assigning conflicting peripherals to the same pin is a common lockup cause. Verify the programming/debug pin mapping before committing the layout. This page synthesizes verified distributor pricing, drop-in same-package alternatives, AEC-Q100 qualifications, and practical design notes not consolidated on any single manufacturer or distributor product page.

Angebot Kontakt

PIC24FJ256GB610-I/BG

PIC24FJ256GB610-I/BG - 256KB Flash USB XLP MCU 121-TFBGA | Microchip

The Microchip Technology PIC24FJ256GB610-I/BG is a 16-bit RISC microcontroller from the PIC24F family with 256 KB of dual Flash memory, 32 KB of RAM, and integrated USB On-The-Go (OTG) connectivity, housed in a 121-ball TFBGA package (10x10 mm). It operates at up to 32 MHz with a 16-bit modified Harvard architecture and is part of the eXtreme Low Power (XLP) family with Live Update for in-field firmware swap. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and a rich set of peripherals on one silicon die. The PIC24F family sits in the broader taxonomy of 16-bit microcontrollers -> microcontrollers -> embedded processors -> semiconductors. 16-bit MCUs fill the gap between 8-bit parts (limited math and address space) and 32-bit Cortex-M parts (more complex toolchain, higher cost), making them well-suited for moderate-throughput embedded designs with USB connectivity. Key features of this part include 256 KB of ECC-protected dual Flash (85.5K x 24 organization) with Live Update, 32 KB of RAM, USB OTG with dedicated DMA, multiple serial interfaces (I2C, SPI, UART with IrDA), six PWM channels, eight DMA channels, a 10-bit and 12-bit ADC, and the XLP deep-sleep current regime. The 121-ball TFBGA package supports the device's 121-pin-out at a compact 10x10 mm body height of 1.20 mm, suiting space-constrained applications. The -I temperature grade covers -40C to +85C industrial operation. Architecturally, the PIC24FJ256GB610 uses a 16-bit modified Harvard CPU with single-cycle multiply, a programmable instruction cache, and a peripheral bus that maps timers, capture/compare, ADC, and the USB SIE through independent DMA channels. The dual-bank Flash with Live Update allows one bank to receive new code while the other executes, enabling firmware upgrades without halting the application - a key benefit for industrial and connected devices. Typical applications include USB peripherals and embedded hosts (HID, CDC, mass storage), industrial sensor nodes with USB diagnostics, low-power data loggers, and home/building automation controllers. The Live Update feature is particularly attractive in industrial gateways that must be field-upgradable without service windows. When designing with this part, plan the dual-Flash bank layout early and verify the Live Update boot sequence against your application linker script; the 121-TFBGA requires PCB pads with sub-0.5 mm pitch and reflow profile control to avoid ball-bridge defects. Power-rail decoupling (10 uF + 0.1 uF) must be placed within 5 mm of VDD/VSS balls. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC24FJ256GB610-I/PT

PIC24FJ256GB610-I/PT - 16-bit 32MHz USB MCU 256KB | Microchip

The Microchip Technology PIC24FJ256GB610-I/PT is a 16-bit PIC® microcontroller from the eXtreme Low Power (XLP) family, integrating 256 KB of Flash with Error Correction Code (ECC), 32 KB of RAM, and full-speed USB On-The-Go (OTG) connectivity, operating at up to 32 MHz from a 2.5 V/3.3 V supply. Housed in a 100-pin TQFP (12x12 mm) package, the PIC24FJ256GB610-I/PT adds dual-partition Flash with Live Update capability, allowing in-field firmware upgrades without application downtime. A 16-bit MCU (microcontroller unit) is a processor-class device that integrates a CPU core, volatile memory (RAM), non-volatile program memory (Flash), and on-chip peripherals into a single IC. PIC24F microcontrollers use a 16-bit modified Harvard RISC architecture with a single-cycle hardware multiplier and DSP-friendly instructions, sitting above 8-bit MCUs in performance but below 32-bit ARM Cortex-M devices in code density and clock speed. The PIC24FJ256GB610-I/PT belongs to the broader category of power-management-aware, USB-enabled embedded controllers used in industrial, medical/fitness, computer-peripheral, and portable battery-powered designs. Key features include 256 KB ECC-protected dual-partition Flash, 32 KB RAM, hardware Real-Time Clock and Calendar (RTCC), 24 channels of 12-bit Analog-to-Digital Conversion (with up to 10-bit or 12-bit modes), four UART, three SPI, three I2C peripherals, eight DMA channels, six PWM outputs, and a Charge Time Measurement Unit (CTMU) for capacitive touch. The integrated USB 2.0 Full-Speed OTG controller supports Host, Device, and On-The-Go roles without external PHY. Designed for low-power applications, the XLP variants draw less than 100 nA in Deep Sleep with RTCC retention and provide multiple wake sources including Real-Time Clock alarm, external interrupts, and USB attach/detach events. Typical applications include industrial data loggers with USB mass-storage bridges, portable medical/fitness devices, USB HID peripherals such as keyboards/mice/joysticks, computer docking stations, and battery-powered sensors that require firmware-upgrade capability in the field. When designing with this MCU, leave unused pins configured as outputs driven low or as inputs with the internal weak pull-up enabled. Ensure VUSB and VDD both have a 100 nF decoupling capacitor placed within 5 mm of the respective pins, and add a 4.7 uF bulk capacitor for inrush-tolerant USB bus power. This page synthesizes distributor pricing, drop-in alternatives in the same 100-TQFP package, and practical low-power design notes beyond what the manufacturer datasheet alone provides.

Angebot Kontakt

PIC24FJ256GL405-E/PT

PIC24FJ256GL405-E/PT - 16-Bit MCU, 256KB Flash, USB, LCD | Microchip

The Microchip Technology PIC24FJ256GL405-E/PT is a 16-bit PIC microcontroller from the PIC24FJ GL4 family, featuring 256KB ECC Flash, 32KB RAM, an integrated LCD driver, and full-speed USB, housed in a 48-pin TQFP (7x7 mm) package. It operates at up to 32MHz (16 MIPS) and supports a 2.0V to 3.6V supply range, with an industrial-grade -40C to +125C operating temperature window suitable for harsh-environment embedded designs. A PIC24FJ microcontroller belongs to the broader category of 16-bit Flash microcontrollers, which sit architecturally between 8-bit MCUs (such as PIC16/PIC18) and 32-bit Cortex-M devices. The PIC24F line emphasizes low-power operation, rich Core Independent Peripherals (CIPs), and integrated mixed-signal features, making it a natural fit for human-machine interface, IoT sensor, and battery-powered products. The GL4 family specifically targets low-power applications with LCD displays and USB connectivity. Key features of the PIC24FJ256GL405 include 256KB of ECC Flash with dual-partition support for Over-The-Air (OTA) firmware updates, 32KB SRAM, hardware Real-Time Clock and Calendar (RTCC), multiple 16-bit timers, a 12-bit ADC, configurable logic cells, and CIPs such as PWM, capture, and comparators. The integrated LCD driver supports up to 48 segments, while the integrated full-speed USB 2.0 device/host/OTG controller eliminates the need for an external interface IC. The device uses a 16-bit modified Harvard architecture with a 24-bit instruction word, providing 16 MIPS performance at 32MHz while maintaining low power consumption (typically in the microamp range in sleep modes). The dual-partition Flash architecture allows safe firmware upgrades in the field, with one partition executing code while the other receives new firmware - critical for OTA-capable IoT nodes. Typical applications include low-power IoT sensor nodes, USB-connected medical devices, industrial control panels with LCD readouts, smart energy meters, home automation gateways, and portable consumer products. The combination of USB, LCD, and dual-partition OTA Flash makes the part particularly well suited to connected products requiring field-updatable firmware and a local display. When designing with the PIC24FJ256GL405, pay close attention to the decoupling network (a 100nF ceramic near each VDD/VSS pair plus a bulk 4.7uF) and ensure the 48-pin TQFP layout provides adequate ground copper for thermal performance. The device supports MPLAB X IDE and the MPLAB Harmony v3 ecosystem, including code configurators and peripheral libraries. This page synthesizes distributor stock data, parametric alternatives, and practical design notes that complement the Microchip datasheet.

Angebot Kontakt

PIC24FJ256GL405-I/M4

PIC24FJ256GL405-I/M4 - 32MHz 256KB LCD USB MCU | Microchip

The Microchip Technology PIC24FJ256GL405-I/M4 is a 16-bit PIC24F microcontroller with 256KB Flash, 32KB RAM, integrated LCD controller, and full-speed USB, packaged in a 48-pin UQFN (6x6 mm). It runs at 32MHz delivering 16 MIPS, operates from 2.0V to 3.6V, and offers 39 I/O pins with Dual Partition Flash supporting real-time Over-The-Air (OTA) updates and EEPROM emulation. An LCD microcontroller (LCD MCU) is a single-chip embedded controller that combines a CPU core, non-volatile memory, RAM, and a segmented or dot-matrix LCD driver on the same die. The LCD controller eliminates the need for an external display driver IC, reducing BOM cost and PCB area while keeping software control over contrast, blinking, and multiplexing. In the broader taxonomy, the PIC24FJ256GL405 belongs to the PIC24F -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor family. Key features include up to 256KB Flash with ECC, 32KB SRAM, an integrated segmented LCD driver (up to 64 segments x 8 commons depending on package), full-speed USB 2.0 device/host/OTG, multiple Core Independent Peripherals (CIPs), and a 16-bit Sigma-Delta ADC. The 48-pin UQFN (6x6 mm) package delivers these capabilities in a compact form factor suitable for handheld and space-constrained products. The 'GL4' architecture supports Dual Partition Flash, enabling live firmware updates without service interruption - critical for IoT and field-deployed products. Its CIP ecosystem (CLC, SCCP, MCCP, RTCC, DMA) handles events without CPU intervention, lowering power consumption and freeing the core for application logic. The integrated segmented LCD controller supports resistive and capacitive touch via dedicated hardware. Typical applications include IoT sensor hubs with integrated LCD displays, low-power medical monitoring devices, smart home control panels, industrial HMI modules, automotive instrument clusters, and battery-powered wearables. The combination of USB and LCD eliminates two external ICs, simplifying the BOM and reducing quiescent current in standby. When designing with this part, ensure the USB D+/D- traces are 90 ohm differential, route the VUSB capacitor close to pin, and select 2.5V or 3.3V LCD bias based on the glass type. Dual Partition Flash must be enabled via configuration bits to use OTA firmware update. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ256GL405-I/PT

PIC24FJ256GL405-I/PT - 16-bit 256KB Flash LCD MCU, 48-TQFP

The Microchip Technology PIC24FJ256GL405-I/PT is a 16-bit PIC microcontroller in the PIC24FJ 'GU4/GL4' family, featuring 256KB of ECC Flash, 32KB RAM, an integrated segmented LCD controller, and full-speed USB in a 48-pin TQFP (7x7 mm) package. It runs up to 32MHz (16 MIPS) from a 2.0V to 3.6V supply and supports on-the-fly Dual Partition Flash for real-time Over-The-Air (OTA) firmware updates and EEPROM emulation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a rich set of peripherals such as timers, communication interfaces, ADCs, and increasingly domain-specific blocks like LCD segment drivers or USB transceivers. The PIC24FJ family sits in the 16-bit microcontrollers tier of the broader embedded computing taxonomy: 8-bit MCUs -> 16-bit MCUs -> 32-bit ARM Cortex MCUs -> application processors. PIC24F parts in particular target low-power, LCD-driven human-machine interface (HMI) products where battery life and segment display integration matter more than raw CPU throughput. Key features of the PIC24FJ256GL405-I/PT include 256KB of Flash with Error-Correcting Code (ECC), 32KB RAM, hardware LCD segment driver, full-speed USB 2.0 FS, multiple Core Independent Peripherals (CIPs), 12-bit ADC, up to 21 analog channels, and multiple capture/compare/PWM modules. Dual Partition Flash allows a backup image to be stored so a failed firmware update can roll back automatically, which is essential for unattended IoT endpoints. Architecturally, the PIC24FJ256GL405 uses a 16-bit modified Harvard core with separate program and data buses, allowing simultaneous instruction fetch and data access. The ECC-protected Flash stores both code and emulated EEPROM, while CIPs such as CLC, MCCP, and DMA let designers offload tasks from the CPU to lower active run-time and reduce average power consumption in sleep-dominated duty cycles. Typical applications include battery-powered smart thermostats, wearable health monitors, e-meter displays, industrial sensor hubs with LCD readouts, USB-CDC/HID peripherals, and consumer appliances with segmented LCDs. The integrated LCD, USB, and OTA firmware make it a strong fit for connected HMI products that must run for years on a coin cell or two AA cells. When designing with this MCU, pay attention to decoupling near the VDD/VSS pairs and route the USB DP/DNM lines as a 90 ohm differential pair. For OTA, leave at least one Dual Partition slot fully programmed as the golden image so a watchdog-assisted rollback can recover from corrupt updates.

Angebot Kontakt

PIC24FJ256GL406-E/MR

PIC24FJ256GL406-E/MR - 256KB Flash LCD MCU, 64-QFN | Microchip

The Microchip Technology PIC24FJ256GL406-E/MR is a 16-bit microcontroller from the PIC24F eXtreme Low-Power 'GL4' family, featuring 256KB of ECC Flash, 32KB RAM, an integrated segmented LCD controller, and full-speed USB, housed in a 64-pin QFN (9x9 mm) package with extended automotive temperature grade. A 16-bit microcontroller (MCU) is a single-chip processor with an internal data path width of 16 bits, optimized for embedded control applications that require more computational precision and code density than 8-bit parts while consuming less power than 32-bit devices. The PIC24FJ GL4 family belongs to the broader Microchip MCU taxonomy: PIC24F -> PIC24 -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor. These devices are commonly used in applications requiring low active and sleep currents, hardware USB, and a built-in segmented LCD driver. Key features of the PIC24FJ256GL406-E/MR include a 32 MHz maximum CPU clock (16 MIPS), 54 digital I/O pins, hardware USB 2.0 full-speed transceiver, 17-bit x 17-bit single-cycle hardware multiplier, and a 32-bit by 16-bit hardware divider. The device also integrates core-independent peripherals (CIPs) such as configurable logic cells, multiple PWM/SCCP/MCCP timers, 12-bit ADC with up to 30 channels, comparators, and a segmented LCD controller supporting up to 512 segments. The 'GL4' architecture is built on a modified Harvard design with a 24-bit instruction word and 16-bit data path. Dual-partition Flash memory (Live Update Flash) enables real-time Over-The-Air (OTA) firmware upgrades without device reset, supporting both bootloader and EEPROM emulation use cases. Power management features include multiple low-power sleep modes, a low-power RTCC, and operation from 2.0V to 3.6V, making the part well-suited to battery-powered and energy-harvesting applications. Typical applications include battery-powered human-machine interface (HMI) panels with LCD, automotive dashboards and instrument clusters, IoT sensor nodes with USB diagnostic interfaces, e-paper/epaper thermostats, and medical glucose/patient monitors. The combination of low power, integrated LCD, and USB makes it a strong fit for handheld industrial and consumer devices. When designing with this device, allocate sufficient PCB area for the 64-QFN (9x9 mm) exposed pad, which must be soldered to a ground copper pour for proper thermal dissipation. Verify that your debugger/programmer (e.g., PICkit 4 or MPLAB ICD 4) supports the GL4 family before committing to the platform. This page synthesizes distributor pricing, same-brand drop-in alternatives drawn from the PIC24FJ GL4 family, and practical design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ256GL406-E/PT

PIC24FJ256GL406-E/PT - 16-Bit 32MHz 256KB Flash LCD MCU | Microchip

The Microchip Technology PIC24FJ256GL406-E/PT is a 16-bit, 32 MHz PIC microcontroller with 256 KB Flash, 32 KB RAM, integrated segmented LCD controller, and full-speed USB, housed in a 64-pin TQFP (10x10 mm) package. It belongs to the PIC24FJ "GU4/GL4" family, which supports up to 512 KB of dual-partition Flash for real-time Over-The-Air (OTA) updates and EEPROM emulation, and includes multiple Core Independent Peripherals (CIPs). A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, and peripherals. 16-bit PIC MCUs use a modified Harvard architecture with 16-bit instructions optimized for deterministic embedded control. The PIC24FJ family sits in the mid-range of Microchip's portfolio - more capable than 8-bit PIC10/12/16 parts and lower cost than 32-bit PIC32 families. It serves in the broader taxonomy: microcontroller -> embedded MCU -> semiconductor IC -> electronic component. Key features include 16 MIPS CPU performance from the 32 MHz oscillator, hardware Cryptographic Engine, 24-bit PWM, 12-bit ADC at 200 ksps, multiple UART/SPI/I2C, full-speed USB 2.0 device/host/OTG, segmented LCD driver (up to 296 segments), and 16-bit Parallel Master Port. The dual-partition Flash with live update support enables firmware upgrades without downtime, critical for connected IoT and industrial sensor nodes. The 'GL' variant of the family targets low-power, graphics-rich embedded designs such as metering, e-bike dashboards, white goods, healthcare monitors, and human-machine interface panels. Core Independent Peripherals - including CLC, MCCP, and SMT - allow complex event-driven tasks to run without CPU intervention, lowering average current draw and freeing MIPS for the application. Typical applications include LoRa/BLE IoT sensor nodes, industrial automation controllers, smart thermostats, e-metering, glucose meters, infusion pumps, and USB peripherals. The 64-pin TQFP package provides ample I/O for human-interface segments, capacitive touch, and display integration. When designing with this MCU, allocate sufficient Flash for OTA staging and plan a boot loader in a protected partition. Use Microchip's MPLAB X IDE and MCC code configurator; verify the segment count and bias for your LCD glass against the datasheet's segment mapping tables. This page synthesizes distributor pricing, drop-in same-package alternatives, application guidance, and design notes not consolidated on the manufacturer product page.

Angebot Kontakt

PIC24FJ256GL406-I/MR

PIC24FJ256GL406-I/MR - 16-Bit MCU, 32MHz, 256KB Flash, 64-QFN | Microchip

The Microchip PIC24FJ256GL406-I/MR is a 16-bit microcontroller from the PIC24F 'GL4' family, delivering 32MHz (16 MIPS) performance with 256KB ECC Flash and 32KB RAM in a 64-pin QFN (9x9 mm) package with exposed pad. The part is a member of Microchip's low-power, full-feature GU4/GL4 family which integrates a segmented LCD driver, full-speed USB, and core-independent peripherals (CIPs) for real-time control without CPU intervention. A 16-bit microcontroller (MCU) is a microprocessor optimized for embedded control, featuring a wider data path than 8-bit parts, integrated peripherals (timers, ADC, communications), and on-chip memory. Within the semiconductor hierarchy, MCUs sit inside the embedded processors category alongside DSPs, FPGAs, and microprocessors, and are the workhorse of consumer, industrial, and IoT products that need deterministic real-time response. Key features of the PIC24FJ256GL406 include 256KB ECC Flash with dual-partition support for over-the-air (OTA) firmware updates and EEPROM emulation, 32KB SRAM, hardware LCD segment driver, full-speed USB 2.0 device/host/OTG, and Microchip's eXtreme Low Power (XLP) technology targeting deep-sleep currents in the microamp range. It also offers 14-channel 12-bit ADC, multiple UART/SPI/I2C, and 5 CCP/ECCP modules for motor and PWM control. Architecturally, the device uses a 16-bit modified Harvard core with single-cycle multiplication and a hardware DIV instruction, allowing deterministic interrupt response. Dual-partition Flash lets one bank be live while the other is updated, enabling true OTA firmware swapping for remote sensor and metering deployments. Typical applications include low-power IoT sensor nodes, USB-connected industrial HMI panels with LCD readouts, smart metering, e-paper/E-ink controllers, and battery-powered medical wearables. The integrated LCD segment driver eliminates the need for an external LCD controller. When designing in this MCU, ensure the exposed pad (EP) on the 64-QFN is soldered to a sufficiently large ground copper pour to meet thermal and electrical specifications. Configure unused peripherals to their lowest-power state and use the deep-sleep modes with RTCC to achieve multi-year battery life on coin cells. This page consolidates distributor pricing, drop-in alternative part numbers, and engineering design notes beyond what is reproduced in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ256GL406-I/PT

PIC24FJ256GL406-I/PT - 256KB Flash 16-bit MCU LCD USB | Microchip

The Microchip Technology PIC24FJ256GL406-I/PT is a 16-bit PIC microcontroller from the PIC24FJ GL4 family, featuring 256KB of dual-partition Flash with ECC, 32KB RAM, an integrated segmented LCD controller, and full-speed USB, all housed in a 64-pin TQFP (10x10 mm) package with industrial -40C to +85C temperature rating. The device operates from 2.0V to 3.6V, runs at 32 MHz (16 MIPS), and supports low-power Run/Idle/Sleep modes suited to battery-powered Human-Machine Interface (HMI) panels. What is a low-power 16-bit MCU with integrated LCD? A microcontroller is a single-chip computer that integrates CPU, memory, and peripherals; the PIC24FJ GL4 family adds segmented-LCD drivers, USB, and core-independent peripherals (CIPs) on a Harvard 16-bit core. The dual-partition Flash enables live firmware Over-The-Air (OTA) updates, while CIPs (RTCC, CRC, PWM, ADC, hardware crypto) offload work from the CPU to reduce active time and extend battery life. Key features include 256KB Flash with ECC and dual partition for OTA, 32KB SRAM, hardware real-time clock and calendar (RTCC), segmented LCD driver supporting up to 128 segments, full-speed USB 2.0 device, multiple UART/SPI/I2C interfaces, a 10/12-bit ADC, and Core Independent Peripherals that run without the CPU. The 64-pin TQFP provides ample GPIO while keeping the footprint compact for HMI designs. The PIC24FJ GL4 family uses an enhanced Harvard architecture with a 16-bit data path and 24-bit instructions, achieving 16 MIPS at 32 MHz. On-chip EEPROM emulation is implemented in Flash, allowing byte-level non-volatile storage without an external chip. The integrated LCD controller with charge pump simplifies the BOM for glass-segment displays, while the USB module enables plug-and-play connectivity for diagnostic, logging, or charging applications. Typical applications include low-power IoT sensor nodes, industrial HMI panels with segmented LCD, battery-powered medical devices, USB-connected consumer gadgets, smart thermostats, and metering equipment. The combination of low-power modes, hardware crypto, and OTA firmware update is especially valuable for connected devices that must remain in the field for years. Designers should budget PCB area for the integrated LCD bias network (charge pump capacitors) and the USB DP/DM 90-ohm differential pair. The dual-partition Flash requires bootloader discipline to perform safe live firmware swap; refer to Microchip application notes on OTA update for GL4 devices. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not aggregated on the manufacturer datasheet, with all values traceable to the data_sources URLs provided.

Angebot Kontakt

PIC24FJ256GL406T-I/MR

PIC24FJ256GL406T-I/MR - 16-bit MCU, 256KB Flash, USB, LCD | Microchip

The Microchip Technology PIC24FJ256GL406T-I/MR is a 16-bit microcontroller from the PIC24F family, delivering 16 MIPS performance at 32 MHz and 256 KB of dual-partition Flash with ECC support. Housed in a 64-pin QFN (9x9 mm) package, it features 32 KB SRAM, integrated segmented LCD driver, full-speed USB 2.0, and core independent peripherals (CIPs). The 'GL4' family targets secure OTA firmware updates via dual-partition Flash, allowing live in-field upgrades without external EEPROM. A 16-bit PIC microcontroller is a member of the higher-performance 16-bit MCU category, sitting between 8-bit AVR/PIC MCUs and 32-bit ARM Cortex-M devices. Within the system hierarchy, PIC24F parts belong to the Microcontroller > Embedded Processor > Integrated Circuit taxonomy. The 16-bit modified Harvard architecture balances deterministic interrupt response, rich peripherals, and low power - making PIC24F MCUs common in consumer appliances, industrial sensors, USB human-interface devices, and battery-powered metering where 8-bit cores are too slow but 32-bit MCUs are over-spec. Key features include hardware crypto engine, segmented LCD controller for up to 512 pixels, 12-bit ADC with 16 channels, multiple UART/SPI/I2C interfaces, and eXtreme Low Power (XLP) sleep modes drawing under 1 uA. The dual-partition Flash and EEPROM emulation reduce BOM cost by eliminating external memory chips. The 64-QFN package offers compact layout for space-constrained HMI modules. Typical applications include secure IoT nodes with OTA firmware, USB HID peripherals, metering displays with LCD, automotive AEC-Q100 dashboard sub-modules, and low-power sensor hubs. The wide peripheral integration reduces external components, supporting compact PCB designs with fewer layers. Design tip: the dual-partition Flash requires careful linker script configuration to partition A/B blocks correctly. Refer to Microchip application note TB3134 for OTA reference implementation patterns. AECs and standard PIC24F IDE toolchains (MPLAB X, XC16 compiler) support this device fully.

Angebot Kontakt

PIC24FJ256GL406T-I/PT

PIC24FJ256GL406T-I/PT - 256KB Flash 32KB RAM 16-bit MCU | Microchip

The Microchip Technology PIC24FJ256GL406T-I/PT is a 16-bit PIC24F microcontroller with 256KB ECC Flash, 32KB RAM, integrated LCD driver, and full-speed USB, housed in a 64-pin TQFP (10x10 mm) package. It runs at 32MHz (16 MIPS), supports 2.0V to 3.6V operation, and includes 54 digital I/O pins plus a 10-bit ADC, making it a drop-in high-memory option for the PIC24FJ GL4 family. The dual-partition Flash architecture enables real-time Over-The-Air (OTA) firmware updates and EEPROM emulation without external memory. A PIC24F microcontroller is a 16-bit modified Harvard architecture MCU from Microchip's PIC family, sitting between 8-bit PIC16/PIC18 devices and 32-bit PIC32 parts. PIC24F devices emphasize ultra-low-power sleep modes (nanoWatt XLP technology), rich Core Independent Peripherals (CIPs) that offload tasks from the CPU, and integrated analog such as 10/12-bit ADCs and comparators. Within the PIC taxonomy, PIC24F belongs to power management ICs > microcontrollers > 16-bit MCUs > PIC24F > GL4 sub-family. This places it squarely in the industrial, medical, and consumer-embedded tier where USB, LCD, and low-power CIP-driven design dominate. Key features include hardware Real-Time Clock and Calendar (RTCC) with timestamped deep-sleep wake, 24-channel 10-bit ADC with 500 ksps throughput, USB 2.0 Full-Speed with on-chip transceiver and dedicated DMA, segmented LCD driver for up to 472 pixels, six UART, three I2C, and three SPI peripherals, plus four Configurable Logic Cells (CLC) and two 32-bit timers. ECC on Flash and RAM improves reliability in harsh environments and supports IEC 60730 Class B safety software. Code protection, secure OTP, and unique device ID enable anti-counterfeit and IP protection. The PIC24FJ256GL406 architecture pairs a 16-bit modified Harvard core with a 24-bit instruction word, giving predictable deterministic interrupt latency (5-cycle response) crucial for motor control and digital power loops. The dual-partition Flash is divided into two live banks, allowing firmware updates to run from the alternate partition while the active bank is reprogrammed - delivering true live OTA. Internal LDO and DC-DC switching converter support optimize active current versus sleep current, achieving sub-1uA sleep with RTCC retention. Typical applications include industrial HMI panels with LCD and USB, smart home hubs, medical glucose and infusion meters, e-metering and HVAC controllers, automotive body and accessory modules (AEC-Q100 qualified), ruggedized portable instruments, and low-power IoT sensor nodes with local LCD readout. The wide 2.0V-3.6V range and XLP nanoWatt technology suit battery-powered deployments that must run for years on a single cell. When designing with this part, allocate 100nF and 10uF decoupling near each VDD/VSS pair, place the 12MHz primary oscillator crystal within 5mm of OSC1/OSC2 with a guarded ground pour, and ensure the USB DP/DM trace impedance is 90 ohms differential per USB 2.0 specification. Use the CLC and PWM peripherals for hardware-driven response to keep the CPU in sleep for as long as possible. This page synthesizes distributor pricing, drop-in same-package alternatives from Microchip's PIC24F GL4/GB4 families, and practical PCB/USB design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ256GL408-E/PT

PIC24FJ256GL408-E/PT - 16-bit 32MHz 256KB Flash LCD MCU | Microchip

The Microchip Technology PIC24FJ256GL408-E/PT is a 16-bit PIC microcontroller built on the Harvard architecture, operating at 32 MHz with 16 MIPS throughput, integrating 256 KB of ECC Flash and 32 KB of SRAM in an 80-pin TQFP (12x12 mm) package. It belongs to the PIC24FJ 'GU4/GL4' eXtreme Low-Power family and supports a wide 2.0V-3.6V operating range with 2.5V/3.3V nominal rails. The -E suffix denotes the extended operating temperature grade of -40C to +125C. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and a rich set of peripheral interfaces. The PIC24F family uses a 16-bit modified Harvard core optimized for low-power embedded control, sitting architecturally between 8-bit PIC16/PIC18 devices and 32-bit PIC32 parts. The 'GL4' sub-family adds Core Independent Peripherals (CIPs) such as Configurable Logic Cells, CLC, PWM, RTCC, and an integrated segmented LCD driver. Hypernym: MCU -> microcontroller -> embedded controller -> semiconductor IC. Key features include an integrated full-speed USB 2.0 device/host/OTG controller, segmented LCD driver (up to 512 segments), 12-bit ADC with 200 ksps, up to 9 capture/compare/PWM modules, two I2C, three UART, and three SPI/I2S interfaces. The 256 KB Flash supports Dual Partition OTA firmware updates and EEPROM emulation, eliminating the need for an external EEPROM. Up to 69 general-purpose I/O pins are brought out through Peripheral Pin Select (PPS), giving flexible signal routing without package re-spins. The 'GU4/GL4' architecture combines an LCD controller, USB, and CIPs in a single die for ultra-low-power applications. Power-saving modes include Idle, Sleep (with RTCC retention drawing only hundreds of nA), Deep Sleep, and VBAT mode for RTC backup from a coin cell. The integrated 32 kHz RTCC and ultra-low-power wake-up sources enable years of operation from a single CR2032 battery in metering or sensor products. Typical applications include industrial LCD keypads and HMI panels, USB-connected sensor hubs, e-metering and energy-monitoring displays, medical infusion pumps, consumer appliances with user interfaces, and battery-powered IoT edge nodes with segmented LCD readouts. The integrated LCD and USB significantly reduce BOM cost versus discrete implementations. When designing with the PIC24FJ256GL408-E/PT, ensure VDD decoupling is placed within 3 mm of every VDD/VSS pair, route the USB DP/DM traces as a 90 ohm differential pair with length matching within 150 mil, and follow Microchip's MSSP layout guidelines for noise-sensitive analog inputs. Use MPLAB X IDE with the XC16 compiler for code development and the PICkit 5 or ICD 4 for programming/debugging.

Angebot Kontakt

PIC24FJ256GL408-I/PT

PIC24FJ256GL408-I/PT - 16-Bit MCU, 256KB Flash, LCD, USB | Microchip

The Microchip PIC24FJ256GL408-I/PT is a 16-bit eXtreme Low-Power microcontroller from the PIC24FJ 'GU4/GL4' family, offering 256KB of ECC Flash, 32KB RAM, an integrated segment LCD controller, and full-speed USB in an 80-pin TQFP (PT) package. It operates at up to 32MHz (16 MIPS) across a 2.0V–3.6V supply range, with dual-partition Flash supporting real-time Over-The-Air (OTA) updates and EEPROM emulation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash/RAM), and programmable peripherals. The 'F' suffix indicates a Flash-based PIC24F device, while 'J' denotes the enhanced 16-bit core. Within the broader taxonomy, this part sits as: PIC24FJ → 16-bit MCU → microcontroller → embedded processor → semiconductor. This positioning makes it well-suited for human-machine interface (HMI) applications where integrated LCD drive and USB connectivity reduce system BOM. Key features include core-independent peripherals (CIPs) such as Configurable Logic Cells (CLC), Multiple Output Capture/Compare/PWM, and a 12-bit ADC with up to 24 channels. The integrated segmented LCD driver supports up to 480 segments with contrast control, and hardware crypto accelerators (AES/SHA) are available on select family members. The 32MHz operation at 3.3V delivers 16 MIPS, while eXtreme Low-Power technology enables deep sleep currents in the microampere range for battery-operated designs. Typical applications include industrial control panels, medical monitoring devices with LCD readouts, e-metering/HVAC thermostats, USB-connected sensor hubs, and OTA-updatable IoT edge nodes. The dual-partition Flash architecture is especially valuable for in-field firmware upgrades where maintaining a known-good image is critical. When designing with this MCU, allocate pin mapping early since the 80-pin TQFP offers a generous but bounded I/O count. Use the integrated LCD charge pump to bias the display, and leverage the DMA engine to offload data movement from the core for sustained USB throughput.

Angebot Kontakt

PIC24FJ256GL408T-I/PT

PIC24FJ256GL408T-I/PT - 16-bit MCU, 256KB Flash, LCD, USB | Microchip

The Microchip Technology PIC24FJ256GL408T-I/PT is a 16-bit PIC microcontroller featuring 256KB ECC Flash, 32KB RAM, integrated LCD driver, and full-speed USB, housed in an 80-pin TQFP (12x12 mm) package. It belongs to the PIC24FJ GL4 family, which offers up to 512KB of Dual Partition Flash supporting real-time Over-The-Air (OTA) updates and EEPROM emulation. The device operates at up to 32 MHz (16 MIPS) from a 2.0V to 3.6V supply, suiting it for low-power and battery-backed embedded systems. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals such as timers, communication controllers, and analog blocks. The PIC24FJ GL4 family sits in the broader taxonomy of 16-bit microcontrollers -> PIC microcontrollers -> Microchip 16-bit MCUs -> embedded microcontrollers -> semiconductor ICs. The 'FJ' suffix denotes the Flash-based enhanced PIC24F architecture with nanoWatt XLP low-power technology, while the 'GL4' family extends the lineup with a hardware LCD segment driver and full-speed USB 2.0. Key features include 256KB Flash with Error-Correcting Code (ECC), 32KB SRAM, hardware LCD controller supporting up to 480 segments, full-speed USB 2.0 device/host/OTG, 4 dedicated DMA channels, and a Peripheral Pin Select (PPS) remappable I/O system. Core-independent peripherals (CIPs) such as the Configurable Logic Cell (CLC), Multiple Capture/Compare/PWM (MCCP/SCCP), and 12-bit ADC with up to 24 channels reduce CPU overhead and enable event-driven designs. The device also integrates a Real-Time Clock/Calendar (RTCC) with backup domain, cryptographic support, and a true random number generator for secure applications. The 'T' suffix indicates Tape and Reel packaging, and 'I' indicates the industrial -40C to +85C operating temperature range. The 'PT' suffix is the Microchip package designator for the 80-pin TQFP. Drop-in compatible variants exist within the same family in TQFP-80 footprints including PIC24FJ256GL408-I/PT (tray, same die) and the wider 256KB GL4 family. The device targets human-machine interface (HMI) and connected embedded applications where a built-in LCD driver and USB simplify the BOM. Typical applications include low-power IoT sensor nodes with USB connectivity, medical glucose meters and patient monitors with segment LCDs, industrial control panels with HMI displays, secure payment terminals with hardware crypto, and automotive dashboard sub-modules (consult PIC24FJ256GL408-E/PT for extended temperature variants). When designing with this MCU, pay attention to the RTCC backup domain and Vbat pin requirements for battery-backed RTC operation, and ensure proper decoupling on Vdd/Vss pairs as outlined in the device datasheet. The PIC24FJ256GL408T-I/PT is supplied on a 1600-unit tape-and-reel reel with a 12 mm body, and is supported by Microchip's MPLAB X IDE, MPLAB Code Configurator (MCC), and the XC16 C compiler toolchain. Pricing and stock should be confirmed at the time of order, as the part is in active production but subject to allocation. This page synthesizes distributor pricing, drop-in alternatives from the PIC24FJ GL4 family, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ256GL410-E/PT

PIC24FJ256GL410-E/PT - 16-Bit 256KB Flash MCU w/ USB & LCD | Microchip

The Microchip Technology PIC24FJ256GL410-E/PT is a 16-bit eXtreme Low-Power microcontroller from the PIC24F 'GL4' family, integrating 256KB of dual-partition Flash, 32KB RAM, a full-speed USB 2.0 device controller, a segmented LCD controller with up to 512 segments, and a rich set of Core Independent Peripherals (CIPs). Housed in a 100-pin TQFP (12x12 mm) package, it operates at up to 32 MHz (16 MIPS) with a wide 2.0V-3.6V supply range. A microcontroller (MCU) is a single-chip computer that contains a processor core, program memory (Flash), data memory (RAM), and a wide array of integrated peripherals such as timers, communication interfaces, ADCs, and CIPs. MCUs belong to the broader category of embedded processors (sitting alongside microprocessors and DSPs) and form the lowest tier of the embedded-computing hierarchy, executing firmware directly from on-chip Flash to control real-world systems. The PIC24F family in particular targets low-power, deterministic applications, ranking as a 16-bit MCU -> 16-bit embedded controller -> microcontroller -> embedded processor -> semiconductor. Key features of the PIC24FJ256GL410-E/PT include up to 512KB dual-partition Flash supporting live Over-The-Air (OTA) firmware updates with EEPROM emulation, a 10-bit ADC and a 10/12-bit ADC variant, hardware crypto acceleration, deep sleep current in the nanoamp range, and multiple CIPs such as Configurable Logic Cells and 16-bit PWM. The 100-pin TQFP package provides ample GPIO for driving segmented LCD glass directly while still exposing USB, I2C, SPI, UART, and PPS (Peripheral Pin Select). Architecturally, the device uses a 16-bit modified Harvard core with a 24-bit instruction word and 16-bit data path, paired with a highly flexible clock tree that supports run, idle, and sleep modes for energy-aware design. The dual-partition Flash is the central differentiator, allowing one partition to run code while the other receives an OTA update. Typical applications include IoT edge nodes with secure OTA, smart metering, medical wearables, industrial HMI panels with segmented LCD, USB human-interface devices, and low-power sensor hubs. When designing with this MCU, allocate a portion of Flash for OTA staging, plan segmented-LCD bias networks carefully, and use PPS to remap peripherals without board rework.

Angebot Kontakt

PIC24FJ256GL410-I/PT

PIC24FJ256GL410-I/PT - 16-Bit 32MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC24FJ256GL410-I/PT is a 16-bit eXtreme Low-Power microcontroller featuring 256KB of ECC Flash and 32KB of RAM, operating at 32MHz with 16 MIPS performance, housed in a 100-pin TQFP (12x12 mm) package. It integrates a segmented LCD controller, full-speed USB, and a rich set of Core Independent Peripherals (CIPs) including a 12-bit ADC and multiple communication interfaces for embedded designs requiring mixed-signal capability. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (typically Flash), working memory (RAM), and a range of integrated peripherals such as timers, ADC/DAC converters, communication controllers, and GPIO. The PIC24FJ family belongs to the broader 16-bit MCU class, sitting architecturally between 8-bit MCUs (PIC16, ATmega) and 32-bit Cortex-M devices. Within Microchip's product hierarchy, the PIC24FJ256GL410 falls under the eXtreme Low-Power category, which is a subfamily of the 16-bit PIC24F line, optimized for battery-powered and energy-harvesting applications that still require substantial Flash and feature integration. Key features of this device include up to 256KB Dual Partition Flash with EEPROM emulation, real-time Over-The-Air (OTA) firmware update capability, integrated segmented LCD driver supporting up to 8 common lines and many segment lines, a 12-bit A/D converter with multiple input channels, and multiple UART/SPI/I2C interfaces. The 32MHz maximum operating frequency delivers 16 MIPS throughput for compute-intensive embedded tasks. Core Independent Peripherals (CIPs) such as Configurable Logic Cells, Multiple Output Capture/Compare/PWM, and hardware CRC allow autonomous operation without CPU intervention. The architecture employs a modified Harvard structure with separate program and data buses, a 16-bit data path, and a 24-bit instruction word that includes an integrated hardware multiplier/Divide engine for DSP-like operations. This combines the simplicity of an 8-bit MCU development flow with the performance headroom of a 16-bit core, supporting C-coded algorithms from sensor fusion to USB-class stacks. Typical applications include battery-powered IoT sensor nodes, wearable medical devices with LCD displays, industrial metering and data loggers with segmented LCD readouts, USB-connected embedded peripherals, home appliances with user interfaces, and Over-The-Air-updatable consumer electronics. The low-power RUN/IDLE/SLEEP modes combined with the integrated LCD controller make it especially suitable for handheld devices that display information on glass or chip-on-glass LCD panels. When designing with the PIC24FJ256GL410-I/PT, ensure the board layout accommodates the 100-pin TQFP package which requires adequate copper pours for thermal management and stable oscillator performance. Use MPLAB X IDE with the MPLAB Code Configurator (MCC) for peripheral initialization, and consider the Dual Partition Flash feature to enable fail-safe OTA updates. This page synthesizes distributor pricing, drop-in alternatives from the same PIC24FJ family, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC24FJ256GL410T-I/PT

PIC24FJ256GL410T-I/PT - 256KB Flash LCD MCU 100-TQFP | Microchip

The Microchip PIC24FJ256GL410T-I/PT is a 16-bit eXtreme Low-Power microcontroller from the PIC24FJ GL4 family with 256KB of Flash, 32KB RAM, an integrated LCD controller, full-speed USB, and a 16 MIPS CPU core, packaged in a 100-pin TQFP (12x12 mm). The "GL4" family introduces a Dual-Partition Flash architecture that supports real-time Over-The-Air (OTA) firmware updates and EEPROM emulation, making it well suited to field-upgradable IoT nodes and connected sensors. What is a 16-bit microcontroller? A 16-bit MCU is a programmable processor with a 16-bit data path, register file, and ALU, sitting between 8-bit MCUs (lower cost, lower performance) and 32-bit MCUs (higher performance, higher power). The PIC24FJ family targets low-power, mixed-signal embedded applications that need more headroom than 8-bit parts but do not require an ARM Cortex-M core. Within Microchip's taxonomy, the PIC24FJ GL4 family occupies the "ultra-low-power, LCD + USB" niche, bridging the gap between the PIC24FJ GB4 family (more I/O, less USB focus) and the PIC24FJ GA7 family (lower power, no USB). Key features include 256KB (256K x 8) of Flash with error correction, 32KB SRAM, up to 86 general-purpose I/O, an integrated segmented LCD driver, a full-speed USB 2.0 device/host/OTG controller, a 12-bit ADC, multiple Core Independent Peripherals (CIPs) including CLC, PWM, and RTCC, and a 2.0V to 3.6V supply range. The CPU runs up to 32MHz at 16 MIPS, with a hardware multiplier and divider. Deep-sleep currents are in the microamp range, supporting battery-powered designs. The Dual-Partition Flash architecture is the standout technical feature: two independent Flash arrays allow one partition to execute code while the other is being reprogrammed, eliminating update downtime. Combined with the integrated LCD and USB controllers, this architecture simplifies the BOM for connected HMI, meter, and sensor applications that require firmware updateability in the field. Typical applications include battery-powered IoT sensors with LCD displays, smart utility meters, home automation gateways, industrial HMI panels, medical monitoring devices, automotive accessory clusters, and USB-connected data loggers. The integrated USB and LCD reduce the external component count significantly. When designing with this device, place a 0.1 uF decoupling capacitor close to every VDD pin and follow the recommended PCB layout for the USB DP/DM traces (90-ohm differential, length-matched). For OTA updates, leave a dedicated bank of Flash untouched for a fail-safe bootloader and verify the dual-partition handshake sequence from the manufacturer application note. This page synthesizes distributor pricing, drop-in alternative MCU part numbers, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware teams evaluate second-source options and field-update strategies.

Angebot Kontakt

PIC24FJ256GU405-E/M4

PIC24FJ256GU405-E/M4 - 16-Bit 32MHz 256KB Flash USB MCU | Microchip

The Microchip Technology PIC24FJ256GU405-E/M4 is a 16-bit PIC® microcontroller from the eXtreme Low Power PIC24FJ GU4/GL4 family, featuring 256KB of dual-partition Flash, 32KB RAM, a 32MHz (16 MIPS) CPU core, integrated full-speed USB, an LCD controller, and Core Independent Peripherals (CIPs), all in a 48-pin UQFN (6x6 mm) package. The dual-partition Flash architecture enables real-time Over-The-Air (OTA) firmware updates and EEPROM emulation without external storage, which is critical for connected devices that must remain in service during firmware upgrades. Integrated CIPs offload tasks such as PWM, ADC triggering, and signal conditioning from the CPU, allowing extended sleep states and sub-uA/MIPS efficiency. A PIC microcontroller is a compact, self-contained computing subsystem built around a Harvard-architecture CPU, on-chip non-volatile program memory, RAM, and a rich set of peripherals (timers, ADC, communication controllers, I/O). Within the broader semiconductor taxonomy, the PIC24FJ family sits in the 16-bit MCU tier — above 8-bit PIC10/12/16 and below 32-bit ARM Cortex-M parts — and the "FJ" suffix denotes an eXtreme Low Power (XLP) variant optimized for battery and energy-harvesting applications. The "GU" family specifically adds USB and dual-partition Flash to the XLP foundation. Key differentiating features include the dual-partition Flash supporting live OTA updates, hardware CIP blocks for autonomous peripheral operation, a 10-bit 1.1 Msps ADC, multiple UART/SPI/I2C interfaces, and a segmented LCD driver capable of driving up to 288 pixels directly. The integrated USB 2.0 full-speed transceiver with on-chip PHY eliminates the need for an external USB interface chip, reducing BOM cost and PCB area in connected peripherals such as glucose meters, smart thermostats, and asset trackers. At 32MHz the CPU delivers 16 MIPS while the XLP sleep currents allow years of operation from a coin cell. The 48-pin UQFN (6x6 mm) package provides a compact footprint suitable for space-constrained designs, and the industrial-grade -40C to +125C operating range allows deployment in harsh environments. This combination of low power, integrated USB, and live-update Flash makes the GU405 family particularly attractive for medical, industrial IoT, and consumer devices that must support secure firmware updates in the field. Typical applications include USB-based medical sensors, battery-powered industrial IoT nodes with OTA firmware capability, electronic shelf labels and metering front panels that use the LCD controller, consumer wearables with USB charging and data sync, and home automation controllers. For designs that need the same feature set in a larger package or with more I/O, the PIC24FJ256GL405 in 48-pin TQFP/PT or the PIC24FJ256GU410 in 64-pin packages offer drop-in scalability within the same family. A key design consideration is dual-partition Flash mapping: when the OTA feature is enabled, the application must reserve one partition as the update buffer, reducing the contiguous program space available to roughly half. If live updates are not required, the device can be configured as a single contiguous 256KB Flash block with no OTA overhead. The NRST, MCLR, and Vcap pins also require careful PCB layout — the Vcap core regulator decoupling capacitor must be placed within 2mm of the pin for stable operation. This page synthesizes distributor pricing from DigiKey and Mouser, Microchip datasheet specifications, and curated drop-in alternatives from the PIC24FJ GU4/GL4 family that share the 48-pin UQFN footprint — practical engineering context that goes beyond the manufacturer datasheet itself.

Angebot Kontakt

PIC24FJ256GU405-E/PT

PIC24FJ256GU405-E/PT - 16-bit 32MHz 256KB Flash USB MCU | Microchip

The Microchip Technology PIC24FJ256GU405-E/PT is a 16-bit microcontroller from the PIC24F family featuring a 32MHz CPU (16 MIPS), 256KB of ECC Flash, 32KB RAM, integrated full-speed USB 2.0, and an LCD segment driver, packaged in a 48-pin TQFP (7x7 mm). It operates from 2.0V to 3.6V and is AEC-Q100 qualified for automotive use, with 39 general-purpose I/O pins and a rich set of Core Independent Peripherals (CIPs) that allow many subsystems to run without CPU intervention. A 16-bit PIC24F microcontroller is a member of Microchip's eXtreme Low-Power (XLP) family built around the 16-bit modified Harvard architecture. PIC24F MCUs occupy the middle of the PIC family hierarchy: 8-bit PIC MCUs sit below them, and 32-bit PIC32 parts sit above. They are commonly chosen when engineers need more computational headroom than 8-bit parts but lower power and simpler toolchains than Cortex-M devices. The -E temperature suffix indicates an industrial/automotive operating range of -40°C to +125°C, while the /PT suffix denotes the 48-pin TQFP package. The on-chip CIPs include multiple 16-bit timers, configurable logic cells (CLC), a 12-bit 1.1 Msps ADC, multiple UART/SPI/I²C peripherals, a Parallel Master Port, and a segmented LCD controller capable of driving up to 248 segments. The Dual Partition Flash architecture supports live Over-The-Air (OTA) firmware updates with EEPROM emulation, allowing firmware to be replaced at run-time without bricking the device. Typical applications include automotive instrument clusters and HVAC control heads (where the LCD driver and USB are both exploited), IoT edge nodes requiring USB-C DCU bootloading, portable medical devices needing segmented LCD glass, and industrial sensor hubs. With its 5-channel DMA and 32KB RAM, the part can sustain a USB CDC stack plus a foreground sensor sampling loop. When designing with this MCU, the two key trade-offs are RAM-limited DSP workloads (32KB is modest for audio processing) and the 32MHz core ceiling versus 32-bit Cortex-M0+ competitors at similar cost. The integrated LCD and USB combination is the primary reason to choose the PIC24FJ256GU405 over generic 16-bit MCUs. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC24FJ256GU405-I/PT

PIC24FJ256GU405-I/PT - 256KB Flash USB MCU | Microchip

The Microchip PIC24FJ256GU405-I/PT is a 16-bit eXtreme Low-Power microcontroller with 256 KB of ECC Flash and 32 KB of RAM, operating up to 32 MHz (16 MIPS) in a 48-pin TQFP package. It integrates a full-speed USB 2.0 device/host/OTG controller, an integrated segmented LCD driver, Core Independent Peripherals (CIPs), and supports OTA firmware updates via dual-partition Flash. A 16-bit microcontroller (MCU) is a programmable processor that uses a 16-bit data path and instruction word, positioned between 8-bit MCUs (lower power, simpler peripherals) and 32-bit MCUs (higher throughput, richer ecosystems). The PIC24F family from Microchip is engineered for low-power, mixed-signal embedded designs, sitting within the broader hierarchy of microcontrollers -> embedded processors -> semiconductors. The PIC24FJ 'GU4/GL4' family specifically targets applications requiring large memory, USB connectivity, LCD drive, and field upgradability. Key features of the PIC24FJ256GU405 include 256 KB ECC Flash with dual-partition support for live firmware update, 32 KB SRAM, a hardware Real-Time Clock Calendar (RTCC) with VBAT retention, four 16-bit timers, a 12-bit ADC with up to 200 ksps conversion rate, multiple UART/SPI/I2C peripherals, and CIP blocks such as CLC, MCCP, and PWM. The device operates from 2.0 V to 3.6 V and offers eXtreme Low-Power (XLP) sleep currents in the nanoamp range. The architecture combines a 16-bit modified Harvard CPU with a 24-bit instruction word and DSP capability (single-cycle MAC), enabling efficient signal processing without burdening the core. Built-in safety features include ECC on Flash, a code-protect lock, a backup oscillator, and a watchdog timer. The 48-pin TQFP (7x7 mm) provides generous I/O for mixed-signal designs. Typical applications include consumer medical devices (glucometers, blood pressure monitors), portable data loggers, USB peripherals (HID, CDC, vendor-class), industrial HMI with integrated segmented LCD, home automation gateways, and battery-powered IoT sensor nodes. The dual-partition Flash enables remote OTA firmware upgrades without service interruption, ideal for field-deployed equipment. When designing with this MCU, route the USB D+/D- lines as a 90-ohm differential pair with matched length, keep the VUSB capacitor close to the VUSB pin, and place the 32.768 kHz crystal within 5 mm of SOSCO/SOSCI to minimize load capacitance error. The integrated segmented LCD driver simplifies BOM cost in metering and HMI designs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

Unterkategorien

Produkte (32840)

PIC24FJ256GB606T-I/MR - 16-Bit 32MHz USB MCU 256KB Flash | Microchip

PIC24FJ256GB606T-I/PT - 16-Bit MCU 256KB Flash USB 64-TQFP | Microchip

PIC24FJ256GB610-E/BG - 16-Bit 32MHz 256KB Flash MCU | Microchip

PIC24FJ256GB610-E/PT - 16-bit 32MHz 256KB Flash USB MCU | Microchip

PIC24FJ256GB610-I/BG - 256KB Flash USB XLP MCU 121-TFBGA | Microchip

PIC24FJ256GB610-I/PT - 16-bit 32MHz USB MCU 256KB | Microchip

PIC24FJ256GL405-E/PT - 16-Bit MCU, 256KB Flash, USB, LCD | Microchip

PIC24FJ256GL405-I/M4 - 32MHz 256KB LCD USB MCU | Microchip

PIC24FJ256GL405-I/PT - 16-bit 256KB Flash LCD MCU, 48-TQFP

PIC24FJ256GL406-E/MR - 256KB Flash LCD MCU, 64-QFN | Microchip

PIC24FJ256GL406-E/PT - 16-Bit 32MHz 256KB Flash LCD MCU | Microchip

PIC24FJ256GL406-I/MR - 16-Bit MCU, 32MHz, 256KB Flash, 64-QFN | Microchip

PIC24FJ256GL406-I/PT - 256KB Flash 16-bit MCU LCD USB | Microchip

PIC24FJ256GL406T-I/MR - 16-bit MCU, 256KB Flash, USB, LCD | Microchip

PIC24FJ256GL406T-I/PT - 256KB Flash 32KB RAM 16-bit MCU | Microchip

PIC24FJ256GL408-E/PT - 16-bit 32MHz 256KB Flash LCD MCU | Microchip

PIC24FJ256GL408-I/PT - 16-Bit MCU, 256KB Flash, LCD, USB | Microchip

PIC24FJ256GL408T-I/PT - 16-bit MCU, 256KB Flash, LCD, USB | Microchip

PIC24FJ256GL410-E/PT - 16-Bit 256KB Flash MCU w/ USB & LCD | Microchip

PIC24FJ256GL410-I/PT - 16-Bit 32MHz 256KB Flash MCU | Microchip

PIC24FJ256GL410T-I/PT - 256KB Flash LCD MCU 100-TQFP | Microchip

PIC24FJ256GU405-E/M4 - 16-Bit 32MHz 256KB Flash USB MCU | Microchip

PIC24FJ256GU405-E/PT - 16-bit 32MHz 256KB Flash USB MCU | Microchip

PIC24FJ256GU405-I/PT - 256KB Flash USB MCU | Microchip