Integrierte Schaltungen

PIC12F609-E/MS

PIC12F609-E/MS - 1.75KB Flash 8-Bit MCU | Microchip 8-MSOP

The Microchip Technology PIC12F609-E/MS is an 8-bit RISC PIC microcontroller in an 8-pin MSOP package, featuring 1.75 KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and 6 general-purpose I/O pins. The device operates at clock frequencies up to 20 MHz across a supply range of 2.0 V to 5.5 V, with the -E (extended) temperature grade rated from -40 C to +125 C for industrial and harsh-environment use. The integrated 8 MHz internal oscillator eliminates the need for an external crystal on cost-sensitive and space-constrained designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripheral interfaces on one IC. The PIC12F609 belongs to the PIC12F family of mid-range 8-bit microcontrollers (PIC -> microcontroller -> embedded processor -> semiconductor), built on CMOS technology with a RISC instruction set optimized for deterministic execution and low power consumption. This architecture positions it between simple 8-pin PIC10 devices and larger PIC16/PIC18 parts. Key features of the PIC12F609-E/MS include 1.75 KB self-programmable Flash, an 8-channel 10-bit ADC, one 8-bit and one 16-bit timer, an enhanced PWM module, an analog comparator, and an internal 8 MHz oscillator with calibration. The part also offers a power-on reset, brown-out reset, watchdog timer with its own on-chip RC oscillator, and in-circuit serial programming (ICSP) for field upgrades. Typical applications include LED lighting control, battery chargers, sensor signal conditioning, low-power remote controls, and automotive body modules. The wide 2.0-5.5 V supply range and small MSOP-8 footprint suit it to coin-cell powered, hand-held, and sealed-environment designs. When designing with this part, ensure the ICSPDAT/ICSPCLK pins are not held low at power-up to enter programming mode, and keep ADC input source impedance below 10 kohm to preserve 10-bit accuracy. An external decoupling capacitor of 100 nF placed within 5 mm of VDD is recommended for noise immunity. This page synthesizes real-time distributor pricing, drop-in alternatives in the same MSOP-8 footprint, and engineering design notes not aggregated in the Microchip datasheet alone.

Angebot Kontakt

PIC12F609-E/P

PIC12F609-E/P - 8-Bit 20MHz MCU, 1.75KB Flash | Microchip

The Microchip Technology PIC12F609-E/P is an 8-bit Flash-based CMOS microcontroller in an 8-pin PDIP package, operating at up to 20 MHz with 1.75 KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and 5 general-purpose I/O pins. The device belongs to Microchip's PIC12F mid-range family, which sits within the broader 8-bit PIC microcontroller portfolio and is engineered for cost-sensitive embedded control applications where small footprint, low power, and integrated peripherals are essential. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripheral interfaces such as timers, ADC, comparators, and communication modules. Within the system hierarchy, the PIC12F609 is a low-pin-count mid-range 8-bit MCU, falling under the broader category of microcontrollers -> microprocessors -> semiconductors. The PIC mid-range architecture uses a 14-bit instruction word and a Harvard bus structure, delivering deterministic execution and a compact instruction set well suited for state machines, sensor interfacing, and battery-powered products. Key specifications of the PIC12F609-E/P include 1.75 KB Flash, 64 bytes SRAM, 5 I/O pins, an internal 4 MHz / 8 MHz oscillator with PLL support up to 20 MHz, a 10-bit ADC, two comparators, and Microchip's nanoWatt power-saving modes. The device operates across an industrial temperature range (-40C to +125C for the -E suffix) and supports a wide 2.0V to 5.5V supply voltage. Compared with PIC10F baseline parts, the PIC12F609 adds more memory and richer peripherals while keeping the same 8-pin simplicity. The PIC12F609 uses an enhanced mid-range 8-bit core with a hardware multiplier and C-compiler friendly architecture, enabling efficient C code development alongside assembly. The device supports In-Circuit Serial Programming (ICSP) via two pins, allowing firmware updates without removal from the board, which is critical for field-deployed nodes and low-cost production programming. Typical applications include consumer appliance control, LED lighting drivers, sensor signal conditioning, battery chargers, remote controls, and small motor control loops. The 5 I/O pins and integrated ADC and comparators are sufficient for simple closed-loop tasks such as temperature sensing, light-level measurement, and PWM-driven LED dimming or fan control. When designing with the PIC12F609-E/P, plan for a decoupling capacitor close to VDD, route ICSP lines (RB6/ICCK and RB7/ICDAT) to an in-system programming header, and verify the absolute maximum VDD of 5.5V is never exceeded during hot-plug or inductive load transients. Use the nanoWatt sleep modes aggressively in battery-operated designs to extend operating life. This page consolidates manufacturer specifications, real distributor stock and pricing, and drop-in same-family alternatives (with and without the -E industrial temperature grade) into a single technical reference not found in the datasheet alone.

Angebot Kontakt

PIC12F609-E/SN

PIC12F609-E/SN - 8-Bit 20MHz 1.75KB Flash MCU | Microchip | SOIC-8

The Microchip Technology PIC12F609-E/SN is an 8-bit flash-based CMOS microcontroller in a 8-pin SOIC (SN) package, featuring a 1.75 KB (1K x 14) flash program memory, 64 bytes of RAM, and a 20 MHz internal oscillator. It belongs to the PIC12F mid-range family and targets cost-sensitive embedded applications where a small pin count, low power consumption, and deterministic RISC performance are required. A mid-range 8-bit microcontroller (MCU) is a single-chip computer integrating a CPU, non-volatile program memory, working RAM, and configurable I/O peripherals onto one silicon die. Within the broader taxonomy, an 8-bit MCU sits inside the microcontroller family, which itself falls under microcontrollers and processors, then embedded computing, then semiconductors. The PIC12F609 specifically uses Microchip's PIC RISC architecture, executing most instructions in a single 200 ns cycle at 20 MHz, supported by only 35 single-word instructions. This combination of small footprint, easy programmability, and predictable timing is why 8-bit mid-range MCUs remain popular for simple control loops and glue logic. Key features of the PIC12F609 include 6 general-purpose digital I/O pins (with multiplexed analog and comparator functions), a 4-channel 10-bit ADC, two analog comparators with a fixed voltage reference, an enhanced universal synchronous/asynchronous receiver-transmitter (EUSART) module, brown-out reset (BOR) and power-on reset (POR), an 8 MHz internal oscillator (calibrated to ±1 %), and nanoWatt power management that drops quiescent current to the sub-microamp range during sleep. The -E temperature grade specifies an operating range of -40 °C to +125 °C, which is broader than the -I grade and suitable for industrial and outdoor enclosures. Typical applications include consumer remote controls, sensor signal conditioning front-ends, white-goods and small-appliance controllers, LED lighting drivers, low-end battery chargers, and HVAC auxiliary boards. With 6 I/O, a built-in comparator, and an EUSART, designers often use the PIC12F609 to replace discrete logic or older 8-pin legacy microcontrollers, consolidating several discrete functions into a single programmable device. When designing with this part, place a 0.1 µF decoupling capacitor as close as possible to VDD, configure the internal oscillator calibration register during initialization to maximize timing accuracy, and respect the 5.5 V absolute maximum supply rating. For low-power battery applications, leverage the nanoWatt sleep modes and gate the EUSART and ADC off when idle to extend battery life.

Angebot Kontakt

PIC12F609-I/MD

PIC12F609-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12F609-I/MD is an 8-bit Flash-based CMOS PIC microcontroller built on the Mid-Range core with 35 instructions and 8 stack levels, delivering 20 MHz CPU performance from a 1.75 KB (1K x 14) program memory and 64 bytes of RAM. Housed in an 8-pin DFN (4x4 mm) exposed-pad package, this IC integrates an internal 4/8 MHz oscillator, a 25 mA source/sink I/O capability, one 8-bit timer (TMR0), one 16-bit timer (TMR1), a watchdog timer, an enhanced power-on reset, brown-out reset (BOR), in-circuit serial programming (ICSP), and a user-configurable comparator with hysteresis. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, and configurable peripherals designed for embedded control. The PIC12F609 belongs to the 8-bit PIC12 family, part of the Mid-Range architecture tier that sits between baseline 12-bit cores and Enhanced Mid-Range 14-bit cores in the Microchip PIC hierarchy. The family targets cost-sensitive applications requiring deterministic real-time response, ultra-low standby power (nanoWatt technology), and minimal PCB footprint. Key features of the PIC12F609-I/MD include the wide 2.0V to 5.5V operating voltage range that supports both 3.3V and 5V system designs, hardware brown-out reset for predictable recovery from voltage drops, and ICSP that allows in-field firmware updates without removing the part from the board. The comparator with user-configurable hysteresis enables analog threshold detection without external op-amps, while the 25 mA I/O drive directly powers LEDs, relays, and small logic buffers. Five usable I/O pins in an 8-pin package make the device an effective system-on-chip for space-constrained designs. The Mid-Range core executes instructions in a 4-clock cycle, yielding a 200 ns instruction time at 20 MHz, and supports interrupt-on-change and a hardware stack with 8 levels for nested subroutine calls. Internal RC oscillator modes (4 MHz and 8 MHz factory calibrated) eliminate external crystals, reducing BOM cost and assembly complexity for cost-driven consumer products. Typical applications include battery-powered sensor nodes, automotive body electronics (RKE, lighting controllers), consumer appliance controls, LED drivers, and industrial low-end PLCs. The compact DFN-8 footprint is well suited to hand-held and IoT edge devices where PCB area is at a premium and reliability over wide temperature ranges is mandatory. When designing with the PIC12F609-I/MD, ensure the exposed pad is soldered to the PCB ground plane for thermal dissipation and mechanical reliability, and apply Microchip's recommended decoupling of 100 nF plus 10 uF close to VDD. For sleep-mode designs, follow the nanoWatt section of the datasheet carefully to achieve the published standby currents. This page synthesizes distributor pricing, same-package drop-in alternatives from Microchip's PIC12 family, and practical design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC12F609-I/MF

PIC12F609-I/MF - 8-Bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip

The Microchip Technology PIC12F609-I/MF is an 8-bit PIC microcontroller featuring 1.75 KB (1K x 14) of Flash program memory, 64 bytes of RAM, and a 20 MHz internal oscillator, housed in an 8-pin DFN (3x3 mm) package with 6 user I/O pins. It belongs to the PIC12F family of small-footprint, low-pin-count microcontrollers designed for cost-sensitive and space-constrained embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripherals such as timers, comparators, ADCs, and communication interfaces. The 8-bit PIC architecture uses a modified Harvard RISC core with a single accumulator (W) and a 14-bit instruction word, prized for deterministic single-cycle execution and very low power consumption. Within the broader power management hierarchy, 8-bit MCUs sit between simple logic ICs and more capable 32-bit microcontrollers, serving battery-powered IoT nodes, consumer appliances, and automotive sub-systems. The PIC12F609 operates from 2.0 V to 5.5 V across the industrial -40 C to +85 C range and integrates an internal 8 MHz oscillator that can be calibrated in software via the OSCTUNE register, eliminating the need for an external crystal in most designs. Key peripherals include an 8-bit Timer0/Timer2 with prescaler, a 16-bit Timer1, an enhanced PWM module, a comparator with selectable reference, and a 4-channel 10-bit ADC. Brown-out Reset (BOR) and Power-on Reset (POR) are included for robust supply supervision, and an on-chip In-Circuit Serial Programming (ICSP) interface supports field upgrades. The 8-pin DFN (MF) package variant measures only 3x3 mm with a thermally enhanced exposed pad, making it ideal for handheld and wearable designs where every square millimeter matters. Code-compatible siblings such as the PIC12F615, PIC12F617, and PIC12HV609 extend this family with additional PWM channels, comparators, or internal shunt regulators. Typical applications include battery chargers, LED drivers, fan controllers, remote controls, sensor interfaces, and automotive body controllers. For each use case, the wide 2.0-5.5 V supply range allows direct connection to single-cell Li-ion or 3.3 V/5 V regulated rails. Designers should review the datasheet's electrical characteristics section for I-V curve details and derating guidelines specific to the DFN package. When migrating from the PIC12F508/509, the PIC12F609 adds enhanced PWM and an internal oscillator trim, but the pinout is forward-compatible. Ensure your development toolchain (MPLAB X IDE + XC8 compiler) supports the PIC12F609 device ID before reuse. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes beyond the manufacturer datasheet to accelerate your component selection and PCB bring-up.

Angebot Kontakt

PIC12F609-I/P

PIC12F609-I/P - 8-Bit 20MHz Flash MCU | Microchip Technology

The Microchip Technology PIC12F609-I/P is an 8-bit CMOS flash-based microcontroller with up to 20 MHz operating speed, 1.75 KB of program memory organized as 1K x 14, and an 8-pin through-hole DIP package. It is designed for compact embedded-control products where low power, simple integration, and a familiar PIC instruction set are valuable. The verified distributor listing identifies the device as an 8-bit PIC 12F microcontroller with 20 MHz capability and 1.75 KB flash memory. A flash-based microcontroller is a programmable control component that stores its application program in nonvolatile memory and executes firmware to sense inputs, make decisions, and control outputs. In the broader device hierarchy, this product is an 8-bit microcontroller, a microcontroller IC, a semiconductor, and an embedded-processing component. The PIC12F609 family is suitable for basic control, timing, signal conditioning, and low-to-moderate computation tasks. Key verified features include up to 20 MHz operation, 1.75 KB flash memory, 8-bit processing, and an 8-pin DIP package. The product family also includes a mid-range core with 35 instructions and 8 stack levels, according to the supplied family information. Other listed family resources include one 8-bit TMR0 timer, one 16-bit TMR1 timer, and a comparator with user-configurable hysteresis. The supplied manufacturer material also identifies nanoWatt Technology for low-power-oriented designs. The device is intended for applications that do not require a high pin count or large memory footprint. Its 8-pin package simplifies prototyping and through-hole assembly, while flash memory permits firmware to be programmed or updated after manufacture. Compared with larger 32-bit microcontrollers, the PIC12F609-I/P focuses on simplicity, low system overhead, and compact control rather than high throughput or extensive connectivity. Typical applications include small industrial controllers, simple sensor interfaces, timer-based modules, LED-control products, compact appliance controls, and educational embedded systems. The device can be used where a short instruction set, compact package, and deterministic embedded control are more useful than advanced peripherals. The supplied data does not provide complete electrical ratings, memory maps, programming details, or operating-temperature limits, so those values must be verified against the official Microchip datasheet before production design. For a new PCB, confirm the DIP-8 footprint, pin assignments, oscillator configuration, programming interface, and required decoupling. For a replacement, compare the exact package suffix, flash size, instruction set, oscillator behavior, comparator availability, timer resources, and operating range. This page combines the supplied manufacturer and distributor information with practical replacement and design guidance.

Angebot Kontakt

PIC12F609-I/SN

PIC12F609-I/SN - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12F609-I/SN is an 8-bit PIC microcontroller based on a nanoWatt-class CMOS architecture, integrating 1.75KB Flash program memory and 64 bytes of SRAM in an 8-pin SOIC package. It operates at up to 20MHz across a 2V to 5.5V supply range and exposes six general-purpose I/O pins with interrupt-on-change capability, an internal 8MHz oscillator, brown-out reset (BOR) and power-on reset (POR). The -I suffix denotes an industrial temperature grade of -40C to +85C. A microcontroller (MCU) is a single-chip computer containing a CPU, non-volatile program memory, working RAM, and peripheral interfaces. The PIC12F609 belongs to the PIC12F family of 8-pin baseline-to-mid-range PIC microcontrollers, sitting in the broader taxonomy: microcontroller -> embedded processor -> semiconductor. It is designed for ultra-low-power standby applications through nanoWatt technology, offering wake-on-change and watchdog timer modes that minimize quiescent draw to microampere levels. Key features include 1.75KB (1K x 14) self-programmable Flash, six I/O lines with individually selectable weak pull-ups, an 8-bit timer (TMR0) and a 16-bit timer (TMR1), a 10-bit ADC with up to four channels, an enhanced PWM module, and an internal 8MHz oscillator with calibrated accuracy. The on-chip debug circuitry supports in-circuit debugging via two I/O pins, eliminating the need for an expensive emulator. The PIC12F609 uses a RISC-based PIC core with a 14-bit instruction word and a two-stage pipeline, providing deterministic instruction timing that simplifies real-time control. Its 35 instructions and Harvard architecture give it predictable interrupt latency of approximately 200ns at 20MHz. Internal 8MHz and 31kHz oscillators remove the external crystal cost while still supporting a high-frequency mode for time-critical tasks. Typical applications include battery-powered sensors, LED drivers, small appliances, fan controllers, and simple logic replacement. The wide 2V to 5.5V range allows direct connection to two AA cells or a single Li-ion cell, while the small SOIC-8 footprint fits into dense PCBs. When designing with this MCU, allocate pin 4 as the MCLR/VPP reset pin, and reserve GP3 for ICSP programming if in-circuit serial programming is required. Decouple VDD with a 100nF ceramic capacitor placed within 5mm of the pin.

Angebot Kontakt

PIC12F609T-I/MD

PIC12F609T-I/MD - 8-bit PIC MCU, 1.75KB Flash, 20MHz | Microchip

The Microchip Technology PIC12F609T-I/MD is an 8-bit Flash-based CMOS microcontroller from the PIC12 mid-range family, delivering 20 MHz CPU performance with 1.75 KB of Flash program memory and 64 bytes of RAM in an 8-pin DFN package with exposed pad. The suffix "/MD" denotes the 3 mm × 3 mm DFN-8 EP (Exposed Pad) surface-mount package, while the "T" infix identifies Tape-and-Reel packaging. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals onto one die. Within the broader semiconductor taxonomy, MCUs belong to microcontrollers -> embedded processors -> logic ICs -> integrated circuits. The PIC12 sub-family is Microchip's low-pin-count mid-range line, typically used as a cost-optimized replacement for discrete logic or as a compact system controller. The PIC12F609 adds nanoWatt Technology for ultra-low standby power, a comparator, 8-bit and 16-bit timers, watchdog timer (WDT), brown-out reset (BOR), and In-Circuit Serial Programming (ICSP). Key features include a wide 2.0 V to 5.5 V operating voltage range, an internal 4 MHz/8 MHz oscillator (no external crystal required for most designs), six I/O pins capable of 25 mA source/sink current, and a mid-range core with 35 instructions and 8 hardware stack levels. The internal comparator with user-configurable hysteresis enables analog signal conditioning without external op-amps. The PIC12F609 uses a RISC architecture with Harvard bus structure and a 14-bit instruction word. Single-cycle instruction execution at 20 MHz yields 200 ns per instruction, while the nanoWatt technology supports sleep currents typically in the nanoamp range when peripherals are gated off, enabling battery-powered applications that must run for years on a single cell. The on-chip POR and BOR with configurable trip points guard against code corruption during supply transients. Typical applications include low-cost consumer appliance control, battery-powered sensors, LED lighting drivers, simple motor control, automotive interior accessories, IoT edge nodes, and standalone logic replacement. The PIC12F609 is well-suited wherever a handful of I/O lines and a small amount of code can replace discrete logic, timers, and comparators. When designing with this device, allocate pin 4 to GP3/MCLR/ICSP programming, plan for the exposed pad to be soldered to a thermal pad connected to ground for mechanical and thermal performance, and use MPLAB X IDE with XC8 compiler for code development. The ICSP interface uses pins 4 (PGD) and 6 (PGC) for in-circuit programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC12F615-E/P

PIC12F615-E/P - 8-bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC12F615-E/P is an 8-bit PIC® mid-range flash microcontroller running up to 20 MHz instruction execution (200 ns instruction cycle), housed in an 8-pin PDIP through-hole package. It integrates 1.75 KB (1K x 14 words) of self-programmable Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM, with 6 general-purpose I/O pins supporting analog and digital peripherals. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, and peripherals such as timers, ADC, and communication interfaces into one package. In the embedded system hierarchy, an 8-bit PIC MCU sits at the smallest, lowest-cost tier of microcontrollers -> microcontrollers -> integrated circuits -> semiconductors, optimized for deterministic real-time control rather than raw compute throughput. Key features of the PIC12F615 include a 10-bit ADC with up to 4 input channels, two 8-bit timers plus one 16-bit timer, an enhanced PWM module with auto-shutdown, an analog comparator, and a wide 2.0V to 5.5V operating voltage range that simplifies battery-powered designs. Internal 8 MHz and 32 kHz oscillators are provided alongside an external oscillator option, enabling flexible clocking strategies for cost-sensitive applications. Architecturally the PIC12F615 uses Microchip's enhanced mid-range 14-bit instruction set with a single accumulator-based ALU and a hardware stack, providing deterministic interrupt response. The nanoWatt technology adds multiple sleep modes with current draw below 1 µA typical, allowing battery lifetimes measured in years for low-duty-cycle sensor nodes. Typical applications include LED drivers and lighting controllers, small appliance control boards, consumer remote controls, battery chargers, sensor interface modules, and low-end automotive body electronics. The combination of PWM, ADC, and comparator peripherals in an 8-pin package makes the part especially well-suited to driving a single power device while reading one or two analog signals. When designing with the PIC12F615, leave at least 0.1 µF of VDD decoupling within 5 mm of the pin, and reserve the ICSP™ pins (GP0/GP1) for in-circuit serial programming access. For noise-sensitive analog reads, use the dedicated analog VREF or AVSS pin configuration rather than digital I/O sharing. This page synthesizes distributor pricing, verified drop-in alternatives from Microchip's mid-range 8-pin PIC family, and practical design notes not consolidated in any single manufacturer document.

Angebot Kontakt

PIC12F615-E/SN

PIC12F615-E/SN - 8-Bit 20MHz Flash MCU | Microchip | 8-SOIC

The Microchip Technology PIC12F615-E/SN is an 8-pin, 8-bit flash-based CMOS microcontroller with nanowatt technology, operating at up to 20 MHz instruction execution in a 1.4 mm height 8-SOIC package with 6 I/O pins. It integrates 1.75 KB (1K x 14) of self-programmable flash program memory, 64 bytes of RAM, and a 128-byte EEPROM, making it suited to compact, low-power embedded control tasks. The PIC12F615 also includes a 10-bit A/D converter with 4 channels, two 8-bit timers, one 16-bit timer, enhanced PWM/capture/compare, and an internal 8 MHz oscillator with PLL. Background Knowledge: An 8-bit microcontroller (MCU) is a programmable embedded processor that executes instructions 8 bits wide. Flash-based 8-bit MCUs store firmware in non-volatile flash memory and are characterized by deterministic instruction execution, low cost, low power, and small pin counts. The PIC12F family sits within the larger Microchip PIC microcontroller hierarchy: PIC12F -> mid-range 8-bit MCU -> 8-bit MCU family -> microcontroller -> embedded processing IC. Within the 8-bit MCU class, the PIC12F615 belongs to the low-pin-count, flash-based, enhanced mid-range core (PIC16-like instruction set with nanowatt sleep modes and integrated ADC + PWM peripherals). Key features include 1.75 KB flash, 64 B SRAM, 128 B EEPROM, 6 bidirectional I/O, a 10-bit 4-channel ADC, nanoWatt sleep modes for sub-uA standby, an internal oscillator with PLL option, and the enhanced PWM module capable of complementary outputs with dead-band control. Wide supply range from 2.0 V to 5.5 V supports both 3.3 V and 5 V systems. The 20 MHz oscillator drives 200 ns instruction execution, delivering roughly 5 MIPS. Technical depth: PIC12F615 is built on an enhanced mid-range core using a RISC architecture with 35 single-word instructions, an 8-level hardware stack, and a unified program/data bus. Brown-out reset (BOR), power-on reset (POR), watchdog timer with on-chip low-power oscillator, and an in-circuit serial programming (ICSP) interface are integrated. The internal 8 MHz oscillator with selectable 4x PLL provides system clock flexibility without external components. Typical applications include LED lighting control, sensor signal conditioning, small motor and PWM drivers, appliance user-interface controls, smoke/PIR detectors, battery-powered instrumentation, and hobby/educational platforms. The wide supply range and tiny 8-SOIC footprint suit drop-in designs for cost-sensitive, compact assemblies. Design consideration: Provide a 100 nF decoupling capacitor as close as possible to VDD (pin 1), maintain pin 8 (VSS) ground integrity, and configure the configuration word (CONFIG) for clock source and BOR at first programming. Use ICSP pins 4 (GP3) and 6 (GP1) appropriately when in-circuit debugging. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. The data below has been aggregated from the manufacturer datasheet, DigiKey, Mouser, and authorized distributor listings as of 2026-09-15.

Angebot Kontakt

PIC12F615-H/MD

PIC12F615-H/MD - 8-Bit MCU 1.75KB Flash 20MHz | Microchip

The Microchip PIC12F615-H/MD is an 8-pin, Flash-based, 8-bit CMOS microcontroller built on the Mid-Range PIC core with 35 instructions and 8 stack levels. It integrates 1.75 KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and 128 bytes of EEPROM, all inside a compact 8-pin DFN exposed-pad (4x4 mm) surface-mount package. The device executes instructions at up to 20 MHz from its internal 4 MHz or 8 MHz oscillator and provides 5 user-configurable I/O pins capable of sourcing/sinking 25 mA. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), small persistent storage (EEPROM), and configurable I/O on one die. Within the broader semiconductor taxonomy, the PIC12F615 belongs to: microcontroller -> 8-bit MCU -> Flash MCU -> low-pin-count MCU -> PIC Mid-Range core. This class of device is widely used as a cost-optimized "brain" for simple control loops, sensor interfaces, and glue-logic replacement tasks. Key features include a 10-bit ADC with 4 input channels, one comparator with user-configurable hysteresis, two 8-bit timers (TMR0, TMR2), one 16-bit timer (TMR1), and a wide 2.0 V to 5.5 V operating range. The device is AEC-Q100 qualified, supports an extended automotive temperature grade of -40C to +150C (TA), and is supplied in tube packaging. Typical applications include automotive body electronics, LED lighting controllers, battery management peripherals, sensor signal conditioning, and low-cost consumer appliances. The combination of internal oscillator, EEPROM, and ADC eliminates most external components, enabling two-layer PCB designs under 10 mm x 10 mm. When designing with this part, reserve the exposed pad for thermal dissipation and ground connection; do not use it as a no-connect. The -H suffix denotes the high-temperature automotive grade, so confirm that your application's maximum ambient stays below 150C. Programming is supported via Microchip's MPLAB X IDE with PICkit or ICD debuggers.

Angebot Kontakt

PIC12F615-I/MD

PIC12F615-I/MD - 8-bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip

The Microchip Technology PIC12F615-I/MD is an 8-bit Flash-based CMOS microcontroller from the PIC12F family, delivering 20MHz CPU performance with 1.75KB (1K x 14) of Flash program memory in a compact 8-pin DFN (4x4) package. Operating from 2.0V to 5.5V, this microcontroller integrates 64 bytes of RAM and 128 bytes of EEPROM, providing a balanced mix of program density and data storage for low-pin-count embedded designs. The device features six general-purpose I/O pins, a 10-bit ADC, two 8-bit timers plus one 16-bit timer, and Microchip's nanoWatt power-management technology for sleep currents as low as 50nA typical. According to the manufacturer datasheet, the PIC12F615 supports in-circuit serial programming (ICSP) and is protected by Microchip's Low Pin Count Patent (U.S. Patent No. 5,847,450). A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/ROM for code, RAM for data, EEPROM for non-volatile storage), and programmable I/O peripherals. The PIC12F series belongs to Microchip's 8-bit mid-range core architecture, sitting within the broader taxonomy of: PIC12F -> PIC12 family -> PIC mid-range core -> 8-bit microcontroller -> embedded microcontroller -> semiconductor. This 8-bit RISC architecture executes one instruction per clock cycle (except branches) and uses a 14-bit instruction word, enabling compact code density suited to small-footprint applications. Key features include a 20MHz internal/external oscillator, two PWM modules with enhanced capture/compare, a comparator module with absolute voltage reference, and an enhanced USART (EUSART) for serial communication. The 8-DFN (MD) package measures 4x4mm with an exposed pad for thermal dissipation, making the device one of the smallest PIC mid-range MCUs available. Operating temperature range spans -40C to +85C (industrial grade, indicated by the "I" suffix), and the device is qualified to Microchip's standard reliability flow. The PIC12F615 is built on Microchip's nanoWatt process technology, which adds ultra-low-power sleep modes, software-controlled clock scaling, and peripheral disable registers. The 10-bit ADC supports up to 4 analog input channels with internal voltage reference options, while the comparator module can wake the device from sleep. Code protection, brown-out reset (BOR), and watchdog timer (WDT) with dedicated on-chip RC oscillator are all integrated. Typical applications include consumer appliance controls, LED lighting drivers, sensor interface modules, battery-powered remote controls, and small motor/relay controllers. The combination of PWM, ADC, comparator, and EUSART on only six I/O pins makes it ideal for compact mixed-signal designs where board space is at a premium. When designing with the PIC12F615, place a 100nF decoupling capacitor as close as possible to the VDD pin and follow Microchip's recommended PCB layout for the DFN exposed pad (the e-pad must be soldered to the ground plane for proper thermal and electrical performance). Avoid routing high-speed digital signals near the analog AVCC/AVSS pins to minimize ADC noise coupling. This page synthesizes distributor pricing, drop-in pin-compatible alternatives drawn from the same PIC12 family, and practical design notes drawn from Microchip application notes - information not consolidated on any single manufacturer or distributor page.

Angebot Kontakt

PIC12F615-I/MF

PIC12F615-I/MF - 8-bit 20MHz MCU 1.75KB Flash | Microchip | 8-DFN

The Microchip Technology PIC12F615-I/MF is an 8-bit PIC® 12F microcontroller with 20 MHz maximum CPU clock speed, 1.75 KB (1K x 14) of Flash program memory, and 64 bytes of SRAM, housed in an 8-pin DFN (3x3 mm) exposed-pad package. It features six general-purpose I/O pins, an 8 MHz internal oscillator, and a wide 2.0 V to 5.5 V operating supply range, making it suitable for both 3.3 V and 5 V designs. An 8-bit microcontroller (MCU) is a small, self-contained computer-on-a-chip that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals on a single die. The PIC12 architecture belongs to Microchip's PIC® family of RISC microcontrollers, a hierarchy that includes 8-bit, 16-bit, and 32-bit device families, with the 12F sub-family positioned as the low pin-count (8-14 pin) tier used in space-constrained and cost-sensitive embedded designs. Key features of the PIC12F615 include an enhanced mid-range 14-bit instruction set, internal oscillator trimming, on-chip 8 MHz RC oscillator selectable between 8 MHz and 31 kHz LF modes, up to 4 channels of 10-bit ADC, two comparators with rail-to-rail inputs, one 8-bit and one 16-bit timer, an enhanced PWM module, an internal 1.024 V reference, and in-circuit serial programming (ICSP). The device also includes a nanoWatt power-managed sleep mode with 10 nA typical standby current for battery-powered applications. The PIC12F615 uses a CMOS Harvard-architecture RISC core, separating program and data buses so the CPU can fetch instructions while reading data. The Flash-based program memory supports self-programming and ICSP, enabling field firmware updates without removing the part from the board. Typical applications include LED lighting controllers, small appliance controls, sensor signal conditioning, battery chargers, automotive body electronics (non-safety), and IoT edge nodes. The internal 8 MHz oscillator eliminates external crystals, reducing BOM cost and PCB footprint. When designing with this device, ensure the exposed pad (pin 8) is soldered to a sufficient copper pour for thermal dissipation. The internal oscillator accuracy (±1% typical after calibration) is adequate for UART but tight baud-rate-critical applications may require an external crystal. This page synthesizes distributor pricing, drop-in DFN-8 alternatives, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC12F615-I/MS

PIC12F615-I/MS - 8-Bit 20MHz MCU, 1.75KB Flash, 8-MSOP | Microchip

The Microchip Technology PIC12F615-I/MS is an 8-bit flash-based CMOS microcontroller from the PIC® 12F family, integrating a 20 MHz RISC core with 1.75 KB (1K x 14) of flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM in an 8-pin MSOP package. The 'I' suffix indicates the industrial operating temperature range of -40°C to +85°C and a supply voltage range of 2.0 V to 5.5 V, with a typical operating point of 4.5 V to 5.5 V for full 20 MHz performance. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path that fetches, decodes, and executes one instruction per clock cycle in a RISC architecture. Within the broader embedded hierarchy, an MCU sits above a microprocessor in integration by combining CPU, RAM, non-volatile memory, and peripherals (ADC, PWM, timers, comparators) on a single die. The PIC12F615 belongs to Microchip's midrange 8-bit PIC family, which targets cost- and pin-constrained applications where a full 32-bit MCU is overkill but discrete logic is too bulky. Typical end-equipment uses include consumer appliances, LED drivers, battery chargers, and sensor interfaces. Key features include six I/O pins multiplexed with peripherals, four 10-bit ADC channels, one enhanced Capture/Compare/PWM (ECCP) module, one 8-bit timer and one 16-bit timer, an enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and a comparator module. The device supports in-circuit serial programming (ICSP) for field updates, an internal 4 MHz oscillator, and a nanoWatt power-managed sleep mode consuming as little as 20 nA. Hardware interrupts and a 14-bit instruction word provide deterministic real-time response in control loops. The PIC12F615 uses a Harvard-architecture RISC core with separate program and data buses, allowing instruction fetch and operand access to occur in the same cycle. The flash program memory supports 100,000 erase/write cycles typical and >40-year data retention, and the on-chip debug logic enables MPLAB X IDE and ICD programmer integration. The ADC uses a sample-and-hold capacitor with successive-approximation conversion, settling in about 16 µs at 20 MHz. Typical applications include LED lighting control, battery chargers, sensor signal conditioning, low-cost remote controls, and small motor control loops. The 8-MSOP package provides a compact footprint for space-constrained PCBs while remaining hand-solderable for prototyping. When designing with this part, ensure VDD decoupling is placed within 1 cm of the VDD pin with a 0.1 µF ceramic capacitor, and reserve the MCLR pin for either an external reset or the internal weak pull-up. For analog reads, source impedance should stay below 10 kΩ to avoid ADC sampling errors. This page synthesizes distributor pricing, drop-in alternative guidance, and design notes beyond what the manufacturer datasheet alone provides for engineers evaluating PIC12F615-I/MS for new designs or as a replacement on existing layouts.

Angebot Kontakt

PIC12F615-I/P

PIC12F615-I/P - 8-bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip PIC12F615-I/P is an 8-bit Flash-based CMOS microcontroller (MCU) in an 8-pin PDIP through-hole package, featuring a 20 MHz instruction clock, 1.75 KB (1K x 14) of Flash program memory, and 64 bytes of SRAM. Built around Microchip's enhanced mid-range PIC® RISC core, it executes single-cycle instructions in 200 ns at 20 MHz, supports 35 instructions, and operates from 2.0 V to 5.5 V across an industrial -40 °C to +85 °C range. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory, working RAM, data EEPROM, and configurable I/O peripherals into one device. PIC® microcontrollers form a sub-family of 8-bit RISC MCUs from Microchip, where each instruction executes in a fixed number of clock cycles. The 8-pin PIC12F series (mid-range core) is the entry-level tier targeted at space-constrained designs that still need on-chip analog, timers, and interrupts. In the broader hierarchy: PIC12F615 -> PIC12 mid-range family -> PIC12F 8-pin series -> PIC microcontroller -> Microcontroller -> Microprocessor/SoC -> Semiconductor. Key differentiating features include an integrated 10-bit A/D converter with 4 channels, an 8-bit/16-bit timer (Timer0) plus Timer1 and Timer2, two PWM modules with hardware capture/compare/PWM (ECCP + CCP), an enhanced USART (EUSART) with auto-baud detection, a comparator module with internal programmable reference, and an internal 8 MHz oscillator. The device also features an internal voltage reference and a 4x PLL that can boost the internal oscillator to 32 MHz. Six general-purpose I/O pins share package leads with the analog and peripheral functions, enabling a wide range of mixed-signal applications in just 8 pins. Architecturally, the PIC12F615 uses a Harvard memory structure (separate code and data buses) which lets the CPU fetch an instruction and access data in a single cycle. The flash-based program memory is in-circuit programmable via ICSP, and the device is supported by the MPLAB X IDE, XC8 compiler, and Microchip's free development toolchain. The integrated peripherals remove the need for external ADC, comparator, and voltage reference ICs, reducing BOM cost and board area for low-pin-count designs. Typical applications include LED lighting control (using PWM and the comparator for current sensing), battery chargers (ADC for voltage/current sense), small appliance controls (washing machines, coffee makers), power-tool motor control (low-side PWM drive), and IoT sensor edge nodes (ADC + EUSART for sensor readouts). The 2.0 V to 5.5 V operating range makes the part suitable for both 3.3 V and 5 V supply rails. A key design tip: the I/P suffix denotes the industrial temperature grade (-40 °C to +85 °C) and PDIP-8 package. For surface-mount designs, choose the I/SN variant (SOIC-8); for automotive use, the -E/P extended grade is available. When designing, take care to assign unused pins to outputs (not inputs) and add the recommended 0.1 µF Vdd bypass capacitor placed within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in compatible alternatives, recommended companion ICs, and practical design notes that are not found in the manufacturer datasheet alone, giving you a single-page engineering reference for part selection.

Angebot Kontakt

PIC12F615-I/SN

PIC12F615-I/SN - 8-bit MCU, 1.75KB Flash, 20MHz, 8-SOIC | Microchip

The Microchip PIC12F615-I/SN is an 8-bit PIC microcontroller built on a RISC architecture, featuring 1.75KB (1K x 14) of Flash program memory, 64 bytes of RAM, and 128 bytes of EEPROM, all in a compact 8-pin SOIC package. The device operates at up to 20MHz instruction clock and integrates peripherals including a 4-channel 10-bit ADC, one 8-bit and one 16-bit timer, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and a 10-bit PWM with an associated Comparator. The internal 8MHz calibrated oscillator reduces external component count for cost-sensitive applications. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a single-chip computer that processes data in 8-bit chunks, integrating a CPU, non-volatile program memory (typically Flash), working RAM, and peripheral interfaces such as timers, ADCs, and communication ports. Within the broader taxonomy, the PIC12F615 belongs to the microcontroller family -> 8-bit MCU -> PIC10/12/16 mid-range core -> embedded microcontroller -> semiconductor IC. This class of MCU serves as the digital decision-making element in space- and cost-constrained products, replacing discrete logic and analog control circuitry. Key differentiating features include the Full-Bridge PWM output for direct half-bridge and full-bridge motor or lighting control, the on-chip Comparator with programmable reference, and the nanoWatt Technology power-management modes that drop quiescent current to under 100nA during sleep. The Flash-based program memory supports in-circuit serial programming (ICSP) and self-programming, while the wide 2.0V to 5.5V operating range allows direct Li-ion, 3.3V, and 5V system rails. The 8-pin footprint delivers these capabilities in the smallest Microchip mid-range package. Architecturally, the PIC12F615 uses a 14-bit wide instruction word with a single accumulator and Harvard bus, achieving deterministic single-cycle instruction execution except for program branches. The Enhanced Mid-Range core adds C-compiler-friendly instructions, hardware stack, and interrupt prioritization, while the configurable oscillator block supports internal 8MHz, internal 31kHz, and external clock modes for EMI or accuracy trade-offs. Typical applications include DC fan speed controllers (the PIC12F615 was designed with fan-control support), small appliance controls, LED drivers, sensor signal conditioning, and battery-powered remote nodes. Designers also use it in HV half-bridge/bridge drivers when paired with external FETs, in smart sensors with analog front ends, and in low-cost replacement of legacy 8-pin PIC10/12F parts. When designing with this device, ensure decoupling on VDD with a 0.1uF ceramic capacitor placed within 5mm of the pin, and respect the maximum source/sink of 25mA per GPIO. The ICSP pins (GP0/GP1) must be accessible for in-circuit programming and debugging with a PICkit 3 or MPLAB Snap. This page synthesizes distributor pricing, drop-in PIC12F family alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Angebot Kontakt

PIC12F615T-I/MF

PIC12F615T-I/MF - 8-Bit 20MHz MCU, 1.75KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12F615T-I/MF is an 8-bit PIC microcontroller in the PIC12F family, offering up to 20 MHz CPU speed, 1.75 KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and 6 I/O pins in a compact 8-pin DFN (3x3 mm, exposed pad) package. It integrates a precision analog comparator, an internal 4/8 MHz oscillator with user calibration, two 8-bit timers (TMR0/TMR2), one 16-bit timer (TMR1), and 25 mA source/sink I/O capability for direct LED or relay drive. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and programmable peripherals (timers, ADC, communication interfaces) on one die. The PIC12F615 belongs to the mid-range PIC architecture with 35 instructions, 8 stack levels, and Harvard memory organization. Within the broader taxonomy it sits at: PIC12F -> PIC12 family -> PIC microcontroller -> Microcontroller (MCU) -> Microprocessor & Embedded IC -> Semiconductor. The "12F" suffix indicates Flash-based program memory and small 8/14/20-pin pin-count family. Key features include 1.75 KB Flash (10,000 erase/write cycles typical), 64 bytes SRAM, in-circuit serial programming (ICSP) via two pins, ultra-low-power wake-up, a wide 2.0V-5.5V operating voltage range (the "HV" siblings extend to 15V for fan-control applications), and a user-configurable comparator with hysteresis. The 8-pin DFN package combines a 3x3 mm footprint with an exposed thermal pad that enhances power dissipation for harsh industrial environments. The mid-range PIC12F615 core executes one instruction per cycle except for branches, giving deterministic interrupt latency suited to real-time control. Its internal 4 MHz or 8 MHz oscillator eliminates external crystal cost, while the 20 MHz external clock option supports higher-speed UART, SPI, and timing applications. The integrated analog comparator plus the Capture/Compare/PWM module enables brushed DC motor control, fan control, and battery-charging regulation without external analog circuitry. Typical applications include fan/motor control (especially with the HV variant), LED driving circuits, battery chargers, small appliance controllers, IoT sensor nodes, smoke detectors, remote control transmitters, and low-cost general-purpose embedded control. The 8-pin DFN variant (T-I/MF suffix) targets space-constrained surface-mount designs in commercial and industrial-grade temperature ranges. When designing with this device, ensure your code fits the 1K x 14 word Flash budget and that interrupt service routines do not exceed the 8-level hardware stack. Use the ICSP clock/data pins for in-circuit programming; isolate them from analog comparator inputs with a series resistor or buffer if both functions are needed simultaneously. This page consolidates real-time distributor pricing, drop-in replacement MPNs, and practical design notes beyond the manufacturer datasheet to accelerate your sourcing and BOM decisions.

Angebot Kontakt

PIC12F615T-I/MS

PIC12F615T-I/MS - 8-Bit 20MHz MCU 1.75KB Flash MSOP-8 | Microchip

The Microchip Technology PIC12F615T-I/MS is an 8-bit PIC microcontroller in the PIC12F family, featuring a 20 MHz CPU core, 1.75 KB (1K x 14) of Flash program memory, and a compact 8-pin MSOP package. The suffix "/MS" identifies the MSOP-8 surface-mount package, while "T" denotes Tape & Reel packaging and "I" indicates the industrial -40C to +85C operating temperature range. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of Harvard-architecture microcontrollers built around a RISC instruction set, a separate program and data memory bus, and integrated peripherals such as timers, ADC, comparators, and PWM. The PIC12F615 belongs to Microchip's mid-range 8-bit lineup, which sits between baseline 8-bit cores and the 16-bit PIC24/dsPIC families. Inside a system it sits below the power management and analog front-end, providing deterministic control of sensors, switches, and small actuators. Key features of the PIC12F615 include 64 bytes of SRAM, 128 bytes of EEPROM, a 4-channel 10-bit ADC, two comparators, enhanced PWM/capture/compare, an internal 8 MHz oscillator, and an operating voltage range of 2.0V to 5.5V. These capabilities let the device drive small-signal logic, battery chargers, LED controllers, and consumer appliance subsystems while drawing minimal current in sleep mode (around 50 nA typical). The architecture combines Microchip's mid-range 8-bit RISC core with NanoWatt technology for low-power operation, an 8 MHz internal RC oscillator, and a configurable instruction set with single-cycle multiply. This blend of deterministic core, integrated analog peripherals, and wide supply range makes the PIC12F615 well suited to compact analog-meets-digital designs. Typical applications include battery chargers, LED drivers, smart sensor nodes, consumer electronics, and small appliance controls. The small MSOP-8 footprint also benefits space-constrained designs such as wearable accessories and IoT edge nodes. Industrial-grade temperature range ensures reliable operation in harsher environments. When designing with the PIC12F615, ensure decoupling with 0.1 uF ceramic capacitors placed close to VDD, and verify the supply voltage stays within 2.0V to 5.5V across all operating conditions. Use MPLAB X IDE with XC8 compiler for code development, and consider the PICkit 4 or Snap programmer for in-circuit debugging. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on any single distributor page.

Angebot Kontakt

PIC12F615T-I/SN

PIC12F615T-I/SN - 8-bit MCU, 2KB Flash, 20MHz, SOIC-8 | Microchip

The Microchip Technology PIC12F615T-I/SN is a member of the PIC® 12F mid-range family of 8-bit flash microcontrollers, offering 1.75KB (1K x 14 words) of program memory, 128 bytes of EEPROM, 64 bytes of RAM, and a 20 MHz internal oscillator core in an 8-pin SOIC (SN) package supplied on tape-and-reel. It integrates six general-purpose I/O pins, a 4-channel 10-bit ADC, two 8-bit timers plus a 16-bit timer, an enhanced PWM/Capture/Compare module, and an internal 4 MHz/8 MHz/32 kHz oscillator block — making it one of the highest-feature-per-pin options in the 8-pin PIC lineup. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and configurable peripherals on a single silicon die. PIC12F microcontrollers in particular occupy the low-pin-count, low-power end of the 8-bit hierarchy — ideal for applications where 8-pin DIP/SOIC form factors, simple deterministic interrupts, and minimal BOM cost matter more than raw CPU throughput. Key differentiating features of this part are its nanoWatt power-management technology with multiple low-power sleep modes drawing as little as a few nanoamps in deep sleep, an on-chip 4/8 MHz precision internal oscillator eliminating external resonator cost, an internal temperature indicator accessible through the ADC, and an in-circuit serial programming (ICSP) interface for field updates via two pins. The Enhanced PWM module supports up to 10-bit resolution, half-bridge and full-bridge outputs, and four PWM channels suitable for driving small DC brushed motors, MOSFET gates, or RGB LEDs. The mid-range PIC architecture uses a 14-bit instruction word, single-cycle execution for most instructions (200 ns at 20 MHz), a hardware accumulator-based ALU, and 35 single-word instructions. This RISC-style instruction set is what makes the 12F family famous for predictable, deterministic interrupt response — important in motor control and timing-critical sensor reading. The device operates from 2.0V to 5.5V, with the 'I' temperature grade covering the industrial -40°C to +85°C range. Typical applications include small DC brushed and stepper motor controllers, RGB LED drivers, ceiling-fan remote controls, low-cost PIR motion sensors, smoke-detector front-end boards, IoT sensor nodes with sleep-duty-cycling, and appliance front-panel control where the 8-pin footprint fits. Designers choose this part for its sub-$1 price point in volume, on-chip oscillator, and Microchip's free MPLAB X IDE + XC8 toolchain. When migrating firmware between PIC12F615 variants, note that the 'T' suffix denotes tape-and-reel packaging and the 'I' suffix denotes the industrial temperature range — the silicon die is identical across temperature grades, but lead-free SOIC-8 reflow profile must be observed on the /SN package. This page synthesizes drop-in PIC12F615T-I/SN alternatives, current distributor pricing, application-specific design notes, and a comparison table not bundled in the manufacturer datasheet.

Angebot Kontakt

PIC12F617-E/MF

PIC12F617-E/MF - 8-bit Flash MCU, 3.5KB, 20MHz, 8-DFN | Microchip

The Microchip Technology PIC12F617-E/MF is an 8-bit Flash-based CMOS microcontroller in the PIC12 mid-range family, packaged in a compact 8-pin DFN (3x3 mm) with exposed pad (MF suffix). The device delivers 20 MHz CPU performance, 3.5 KB of self read/write Flash program memory (2K x 14), 128 bytes of RAM, and 6 general-purpose I/O pins with 25 mA source/sink capability. A configurable internal 4/8 MHz oscillator eliminates the need for an external crystal on cost-sensitive designs. A PIC microcontroller (MCU) is a compact, programmable processor built around a Reduced Instruction Set Computer (RISC) architecture that integrates CPU, non-volatile memory, RAM, and peripherals into a single chip. The PIC12 sub-family sits at the low-end of the PIC hierarchy (PIC10 -> PIC12 -> PIC16 -> PIC18 -> PIC24 -> dsPIC33 -> PIC32) and is designed for space-constrained, low-I/O-count applications where small code size, deterministic execution, and minimal BOM cost outweigh absolute throughput. The mid-range core executes one instruction per 200 ns cycle at 20 MHz. Key features of the PIC12F617 include a user-configurable comparator with hysteresis, a 10-bit ADC, two 8-bit timers (TMR0/TMR2) plus one 16-bit timer (TMR1), a Capture/Compare/PWM (CCP) module, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), and an internal voltage reference. The device operates from 2.0 V to 5.5 V across an industrial temperature range of -40 C to +125 C and is qualified to the AEC-Q100 automotive standard. The architecture combines Harvard-bus separation of program and data memory with a 14-bit instruction word and an 8-level deep hardware stack. Self-programmability over I/CSP allows in-application firmware updates without removing the part from the board, useful for field-serviceable sensor nodes. The EUSART supports LIN (Local Interconnect Network) master/slave operation when the part is paired with an external LIN transceiver, enabling automotive body and chassis networks. Typical applications include LED lighting controllers, sensor interface front-ends, battery-powered IoT edge nodes, automotive body electronics (RKE receivers, interior LED drivers, LIN slaves), small appliance control, and general-purpose glue logic replacement. The combination of AEC-Q100 qualification and a 3x3 mm DFN package makes it attractive for under-the-hood and in-cabin automotive modules where PCB area is at a premium. When designing with this MCU, allocate at least 4 KB of Flash headroom above your compiled code size to leave room for bootloader/IAP routines and field updates. Decouple VDD with a 100 nF ceramic capacitor placed within 2-3 mm of the IC pin and add a bulk 4.7 uF capacitor near the supply input to suppress voltage dips during in-circuit serial programming. This page synthesizes distributor pricing, drop-in package-compatible alternatives from the PIC12F family, and practical design notes not found in the standalone Microchip datasheet.

Angebot Kontakt

PIC12F617-E/MS

PIC12F617-E/MS - 8-Bit 20MHz Flash MCU 3.5KB | Microchip

The Microchip Technology PIC12F617-E/MS is an 8-bit flash-based CMOS microcontroller in the PIC12 mid-range core family, offered in an 8-pin MSOP package. According to the verified distributor data and the Microchip product page, the part integrates a 3.5KB (2K x 14 words) self-read/write flash program memory, 128 bytes SRAM, and a high-performance RISC CPU that executes most instructions in a single 200 ns cycle. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (flash/ROM), working memory (RAM), and peripheral set (timers, ADC, PWM, comparators, communications). The PIC12F617 belongs to the PIC12 sub-family — the lowest pin-count tier of Microchip's mid-range 8-bit architecture — designed for cost-sensitive, space-constrained embedded applications where 6 I/O pins and 8 KB of code space are sufficient. Key feature highlights include an internal 4/8 MHz precision oscillator with software-selectable frequency, a user-configurable comparator with hysteresis, two 8-bit timers (TMR0/TMR2) plus one 16-bit timer (TMR1), a 10-bit ADC, Enhanced PWM, and on-chip debug support. The device operates from 2.0V to 5.5V across the extended -40C to +125C temperature range (E suffix = industrial/extended), making it suitable for harsh environments. Architecturally, the PIC12F617 uses Microchip's proven mid-range core with 35 single-word instructions and 8 stack levels, achieving deterministic interrupt response and predictable timing. The 25 mA source/sink I/O capability allows direct drive of LEDs and small relays without external transistors. Typical applications include LED lighting controllers, battery chargers, small appliance controls, sensor signal conditioning, automotive body electronics, and consumer IR remote controls. The compact MSOP-8 footprint suits high-density PCB designs where board area is at a premium. When designing with this device, engineers should plan for ICD/debug header access and verify that the chosen comparator and PWM configurations match the application's timing requirements. The internal oscillator can drift across temperature, so designs requiring tight UART baud-rate tolerance should use an external crystal. This page synthesizes distributor pricing, drop-in MSOP-8 alternatives, and design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC12F617-E/P

PIC12F617-E/P - 8-Bit 20MHz MCU 3.5KB Flash 8-PDIP | Microchip

The Microchip Technology PIC12F617-E/P is an 8-bit PIC® RISC microcontroller running up to 20 MHz, integrating 3.5 KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and 6 I/O pins in an 8-pin PDIP through-hole package. The part is qualified to Microchip's Extended (-40C to +125C) operating range, making it suitable for industrial and automotive-adjacent applications. According to the manufacturer datasheet, the device supports a 2.0V-5.5V supply range, an internal 8 MHz oscillator, and a 10-bit ADC with up to 4 input channels. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data RAM, and peripheral interfaces into one package. Within the broader taxonomy, the PIC12F617 sits at the entry-level of the PIC12 mid-range family -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The 8-bit RISC Harvard architecture executes instructions in a single cycle (200 ns at 20 MHz), and only 35 single-word instructions are required to program the device, simplifying firmware development. PIC microcontrollers dominate cost-sensitive 8-bit applications where deterministic real-time behavior and small package size are critical. Key features of the PIC12F617-E/P include: enhanced Capture/Compare/PWM (ECCP) with auto-shutdown, a comparator module with programmable reference, 5 timer modules, brown-out reset (BOR), power-on reset (POR), and a watchdog timer (WDT). The on-chip 10-bit ADC provides four external analog inputs, enabling direct sensor interfacing without external signal conditioning. The internal 8 MHz oscillator with PLL option eliminates the need for an external crystal, reducing BOM cost and board area. The 8-pin PDIP package offers 6 usable I/O lines (RA0-RA5, with RA3 input-only), 1 VDD pin, 1 VSS pin, and the MCLR/RA5 pin. The 0.300" through-hole form factor (7.62 mm body width) supports prototyping, breadboards, hand-soldered designs, and legacy through-hole production lines. Programming is supported via the In-Circuit Serial Programming (ICSP) interface, allowing in-system firmware updates. Typical applications include LED driver controllers, small sensor signal conditioning, low-end PWM motor control (fans, small solenoids), battery chargers, and replacement of discrete logic. The combination of internal oscillator, ADC, PWM, and comparator enables single-chip solutions for closed-loop analog control loops. When migrating from an 8-bit baseline PIC such as the PIC12F508/509/615 family, the PIC12F617 provides an upgrade path with more peripherals, Flash memory, and analog integration.

Angebot Kontakt

PIC12F617-E/SN

PIC12F617-E/SN - 8-Bit 20MHz 3.5KB Flash MCU 8-SOIC | Microchip

The Microchip Technology PIC12F617-E/SN is an 8-bit flash-based CMOS microcontroller (MCU) featuring a mid-range core that executes instructions in 200 ns and is housed in an 8-pin SOIC (SN) package. It integrates 3.5 KB of self read/write flash program memory, 128 bytes of RAM, 6 I/O lines, and runs at a maximum clock speed of 20 MHz from an internal 4/8 MHz oscillator or external clock. The device operates across a 2.0V-5.5V supply range (extended PIC12F "E" temperature: -40C to +125C). An 8-bit microcontroller (MCU) is a small computer-on-a-chip that combines a CPU, RAM, non-volatile program memory, and peripherals on a single die. Within the broader taxonomy, the PIC12F617 belongs to the PIC12F family of 8-pin flash MCUs, which sits under the mid-range PIC architecture, the Microchip PIC microcontroller family, and ultimately the integrated circuit / semiconductor hierarchy. This class of device is the simplest possible "brain" for an embedded product and is widely used for deterministic real-time control where an ASIC or higher-end MCU would be wasteful. Key features include two 8-bit timers (TMR0/TMR2), one 16-bit timer, an enhanced PWM module, a user-configurable comparator with hysteresis, a 5-channel 10-bit ADC, brown-out reset (BOR), power-on reset (POR), and a watchdog timer (WDT). The 25 mA source/sink I/O capability eliminates the need for external drivers in many LED, relay, and logic-level interface designs, while the internal 4/8 MHz oscillator removes external crystal cost. Architecturally, the PIC12F617 uses Microchip's mid-range 14-bit instruction set with 8 hardware stack levels and 35 single-word instructions. Self-programmable flash supports in-circuit serial programming (ICSP) for field firmware updates, while the comparator+PW+ADC trio enables single-chip analog feedback loops (e.g., closed-loop LED current regulation, threshold detectors, hysteretic converters). Typical applications include LED lighting controllers, battery chargers, smoke detectors, small appliance controls, sensor signal conditioning, and hobby/educational microcontroller platforms. In each, the part's combination of low pin count, on-board peripherals, and wide voltage range lets it replace a discrete analog board. Designers should note that the "E" suffix indicates the -40C to +125C extended industrial temperature grade, versus the "I" suffix parts rated -40C to +85C. Programming is via ICSP using the PICKit or MPLAB ICD tools, with MPLAB X IDE and XC8 compiler as the standard software toolchain. This page consolidates distributor data, drop-in equivalents, and practical design notes not found in the manufacturer datasheet alone.

Angebot Kontakt

PIC12F617-I/MF

PIC12F617-I/MF - 8-bit MCU, 3.5KB Flash, 20MHz | Microchip

The Microchip Technology PIC12F617-I/MF is an 8-bit Flash-based CMOS microcontroller from the PIC® 12F family, delivering 20MHz CPU performance with 3.5KB (2K x 14) of program memory in an 8-pin DFN (3x3 mm) package with exposed pad. It integrates 128 bytes of SRAM, six general-purpose I/O pins, and a 4-channel 10-bit ADC. According to the Microchip product page, the part features a built-in 8MHz internal oscillator plus PWM, comparator, and Enhanced Capture/Compare/PWM (ECCP) peripherals. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data path, typically used for embedded control in cost- and power-sensitive applications. The PIC12F617 belongs to the broader PIC microcontroller family from Microchip, which sits within the hierarchy microcontroller -> embedded processor -> integrated circuit -> semiconductor. Its compact 8-pin DFN footprint and integrated analog peripherals make it a member of the low-pin-count MCU category intended to replace discrete logic and timer circuits in space-constrained designs. Key features include 4.5V to 5.5V supply operation, six I/O pins with interrupt-on-change capability, hardware PWM with ECCP module, two analog comparators, an internal 8MHz oscillator (calibrated to ±1% over voltage and temperature), and in-circuit serial programming (ICSP) via two pins. The 8-pin DFN package exposes a thermal pad that must be soldered to the PCB ground plane to meet the 31.3 C/W theta-JA rating. Architecturally, the PIC12F617 uses Microchip's enhanced mid-range 14-bit instruction set, supporting single-cycle instructions except for branches. The 10-bit ADC runs up to 30 channels of input multiplexing on six I/O pins, with conversion speeds near 8 µs typical. Brown-out reset (BOR), power-on reset (POR), and watchdog timer (WDT) provide system-level reliability. Typical applications include LED lighting controllers, battery chargers, fan/motor PWM drivers, sensor signal conditioning, and consumer appliance control panels. The 8-pin DFN variant specifically targets compact hand-held products where board area is critical and a small exposed-pad footprint aids thermal dissipation. When designing with this part, note the DFN exposed pad must be soldered to a ground-copper pour of at least 0.25 sq. inch to achieve rated thermal performance. Decoupling should place a 100nF capacitor within 2mm of VDD, and ICSP programming requires MCLR, VPP, and serial data/clock lines reserved in layout. This page synthesizes distributor pricing, drop-in 8-pin DFN alternatives, and practical PCB-layout notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

Unterkategorien

Produkte (38.000+)

PIC12F609-E/MS - 1.75KB Flash 8-Bit MCU | Microchip 8-MSOP

PIC12F609-E/P - 8-Bit 20MHz MCU, 1.75KB Flash | Microchip

PIC12F609-E/SN - 8-Bit 20MHz 1.75KB Flash MCU | Microchip | SOIC-8

PIC12F609-I/MD - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

PIC12F609-I/MF - 8-Bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip

PIC12F609-I/P - 8-Bit 20MHz Flash MCU | Microchip Technology

PIC12F609-I/SN - 8-Bit 20MHz 1.75KB Flash MCU | Microchip

PIC12F609T-I/MD - 8-bit PIC MCU, 1.75KB Flash, 20MHz | Microchip

PIC12F615-E/P - 8-bit 20MHz 1.75KB Flash MCU | Microchip

PIC12F615-E/SN - 8-Bit 20MHz Flash MCU | Microchip | 8-SOIC

PIC12F615-H/MD - 8-Bit MCU 1.75KB Flash 20MHz | Microchip

PIC12F615-I/MD - 8-bit MCU, 1.75KB Flash, 20MHz, 8-DFN | Microchip

PIC12F615-I/MF - 8-bit 20MHz MCU 1.75KB Flash | Microchip | 8-DFN

PIC12F615-I/MS - 8-Bit 20MHz MCU, 1.75KB Flash, 8-MSOP | Microchip

PIC12F615-I/P - 8-bit 20MHz 1.75KB Flash MCU | Microchip

PIC12F615-I/SN - 8-bit MCU, 1.75KB Flash, 20MHz, 8-SOIC | Microchip

PIC12F615T-I/MF - 8-Bit 20MHz MCU, 1.75KB Flash, 8-DFN | Microchip

PIC12F615T-I/MS - 8-Bit 20MHz MCU 1.75KB Flash MSOP-8 | Microchip

PIC12F615T-I/SN - 8-bit MCU, 2KB Flash, 20MHz, SOIC-8 | Microchip

PIC12F617-E/MF - 8-bit Flash MCU, 3.5KB, 20MHz, 8-DFN | Microchip

PIC12F617-E/MS - 8-Bit 20MHz Flash MCU 3.5KB | Microchip

PIC12F617-E/P - 8-Bit 20MHz MCU 3.5KB Flash 8-PDIP | Microchip

PIC12F617-E/SN - 8-Bit 20MHz 3.5KB Flash MCU 8-SOIC | Microchip

PIC12F617-I/MF - 8-bit MCU, 3.5KB Flash, 20MHz | Microchip