Integrierte Schaltungen

PIC12LF1572T-I/MS

PIC12LF1572T-I/MS - 8-bit 32MHz MCU 3.5KB Flash 8-MSOP | Microchip

The Microchip Technology PIC12LF1572T-I/MS is an 8-bit PIC12F-series microcontroller built around a 32MHz RISC core, delivering 3.5KB (2K x 14 words) of Flash program memory and 256 bytes of SRAM in an 8-pin MSOP package. It operates from 1.8V to 3.6V with an integrated 16-bit PWM, a 5-bit DAC, and a 4-channel 10-bit ADC for compact mixed-signal designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU core, program memory, RAM, and peripherals onto a single silicon die. In the broader taxonomy, an MCU belongs to the microcontroller family, which falls under microcontrollers, integrated circuits, and finally semiconductors. The PIC12F line targets low-pin-count, cost-sensitive applications where the smallest package and lowest power matter most, and the PIC12LF1572 belongs to the PIC12(L)F157X sub-family that combines 16-bit PWMs with analog peripherals. The "LF" prefix denotes the wide-voltage, low-power variant optimized for battery-powered and energy-harvesting products. Key features include three independent 16-bit PWMs with dedicated timers, a hardware 5-bit DAC that complements the 10-bit ADC, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and up to 6 general-purpose I/O pins. Internal oscillator options eliminate external crystals in many designs, while the in-circuit serial programming (ICSP) interface allows field upgrades. Compared with traditional 8-bit MCUs that only offer 8 or 10-bit PWMs, the 16-bit PWM resolution enables finer control of LED brightness and motor position. Technically, the PIC12LF1572 uses a Harvard RISC architecture with a 14-bit instruction word and single-cycle execution, allowing deterministic interrupt response for real-time control. The 32MHz internal oscillator provides 8 MIPS throughput, with low-power Sleep and Idle modes reducing quiescent current to support battery-operated systems. Typical applications include RGB LED lighting strips, small DC motor or fan speed controllers, low-cost SMPS primary-side control, and consumer remote controls. The combination of wide-voltage operation, high-resolution PWM, and integrated DAC makes it especially well suited to general-purpose lighting and power-conversion tasks. When designing, place the device close to its supply decoupling capacitor and route the analog AVdd/DAC traces away from PWM outputs. Verify that total GPIO sourcing does not exceed the package's 50 mA per-pin limit. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers and buyers a faster path to a qualified design.

Angebot Kontakt

PIC12LF1572T-I/RF

PIC12LF1572T-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

The Microchip PIC12LF1572T-I/RF is an 8-bit CMOS flash microcontroller from the PIC® 12F family, featuring a 32MHz internal oscillator, 3.5KB (2K x 14) of flash program memory, and 256 bytes of RAM, all integrated into a compact 8-pin UDFN (3x3 mm) exposed-pad package with tape-and-reel packaging. It delivers three independent 16-bit PWMs with dedicated timers, an on-chip 5-bit DAC, a comparator, a 10-bit ADC, and an EUSART, making it a versatile solution for mixed-signal applications where high-resolution PWM and analog integration are required in a minimal footprint. A PIC microcontroller (MCU) is a compact programmable processor built on Harvard architecture with separate program and data buses, typically used for embedded control tasks such as sensor reading, motor driving, LED dimming, and signal generation. Within the broader category, the PIC12F family represents the smallest pin-count 8-bit PICs, the PIC12LF sub-family denotes low-voltage (1.8V-3.6V) operation, and PIC microcontrollers in general sit within the wider taxonomy of microcontrollers > processors > semiconductors > integrated circuits. Key features of the PIC12LF1572T-I/RF include three 16-bit PWMs with independent timers suitable for high-resolution LED lighting and motor control, a 5-bit DAC, a comparator, and a 10-bit ADC with up to 6 channels. It supports a wide operating voltage of 1.8V to 3.6V, low-power sleep modes, an integrated 32MHz internal oscillator, and an EUSART module for asynchronous serial communication. The 8-UDFN exposed-pad package provides a compact 3x3 mm footprint with excellent thermal dissipation for high-density PCB layouts. Architecturally, this device uses Microchip's enhanced mid-range 8-bit core with a 14-bit instruction word and a 200 ns instruction execution time at 32MHz. The combination of three independent 16-bit PWM channels, a 5-bit DAC, and a 10-bit ADC in such a small package makes it a unique solution for cost-sensitive designs that need both analog and PWM peripherals in minimal board space. Typical applications include LED lighting control, RGB color mixing, DC-DC converter control, battery management, and small motor control in consumer electronics, IoT nodes, and portable devices. The wide 1.8V-3.6V supply range makes it ideal for direct battery-powered designs. When designing with this MCU, ensure that the UDFN exposed pad is soldered to a sufficient copper area for thermal performance, and review the configuration bits carefully to enable the peripherals you need. The internal 32MHz oscillator eliminates the need for an external crystal, reducing BOM cost. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing actionable information for engineers evaluating the PIC12LF1572T-I/RF for embedded designs.

Angebot Kontakt

PIC12LF1572T-I/SN

PIC12LF1572T-I/SN - 8-Bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

The Microchip Technology PIC12LF1572T-I/SN is an 8-bit RISC microcontroller featuring 3.5KB (2K x 14) of Flash program memory, 256 bytes of SRAM, and a maximum CPU clock speed of 32MHz, all integrated into an 8-pin SOIC package. It operates from a 1.8V to 3.6V supply rail, consumes low active and sleep currents, and integrates three 16-bit PWMs with independent timers, a comparator, a 10-bit ADC with 4 channels, and a 5-bit DAC for high-resolution analog signal generation. A microcontroller (MCU) is a single-chip computer that contains a processor core, volatile and non-volatile memory, and configurable peripheral blocks. The PIC12LF1572 belongs to Microchip's enhanced mid-range PIC12 family, which targets cost-sensitive, low-pin-count embedded applications. In the broader taxonomy, it sits under 8-bit microcontroller -> microcontroller -> embedded processor -> semiconductor, occupying the smallest-footprint tier alongside PIC10, PIC12, and PIC16 families. Key differentiating features of the PIC12LF1572 include three independent 16-bit PWMs (vs. the 10-bit PWM blocks found on older PIC12F parts), a 10-bit ADC with selectable conversion modes, a 5-bit DAC, an Enhanced Universal Synchronous Asynchronous Receiver Transceiver (EUSART), and an inter-module crossbar supporting flexible signal routing between peripherals. The 32MHz internal oscillator eliminates the need for an external crystal in many designs, reducing BOM cost and board area. Architecturally, the PIC12LF1572 uses a Harvard RISC core with a 14-bit instruction word, allowing most instructions to execute in a single instruction cycle (125 ns at 32 MHz FOSC). The on-chip debug logic (ICD) and the in-circuit serial programming (ICSP) interface support Microchip's MPLAB X IDE and PICkit programmers, accelerating firmware bring-up. Typical applications include LED lighting and color-mixing controllers, household appliance user interfaces, battery-powered sensor nodes, simple motor and fan control loops, and general-purpose logic replacement where designers need more flexibility than a discrete 555 timer but fewer resources than a 32-bit MCU. The 16-bit PWM resolution makes the part especially well suited to high-resolution dimming and motor torque control. Designers should pay particular attention to the 1.8V to 3.6V supply range. When migrating from the 5V-tolerant PIC12F1572, note that the 'LF' variant is the low-voltage part - do not power it from a 5V rail or the device will be damaged. Decoupling should follow Microchip's recommended 0.1uF + 10uF capacitor arrangement. This page consolidates distributor pricing, drop-in SOIC-8 alternatives, and practical design notes that go beyond the manufacturer datasheet to help procurement and embedded engineers make a fast, well-informed decision.

Angebot Kontakt

PIC12LF1612-E/MF

PIC12LF1612-E/MF - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

The Microchip PIC12LF1612-E/MF is a 8-bit PIC microcontroller operating at up to 32 MHz with 3.5 KB (2K x 14) of Flash program memory and 256 bytes of RAM, housed in an 8-pin VDFN (3x3 mm) exposed-pad package. The 'LF' prefix denotes the wide-voltage 1.8V-3.6V variant, ideal for battery-powered designs, while the 'E' suffix indicates the -40C to +125C extended operating temperature range suited to industrial environments. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and peripheral set (timers, ADC, communications, comparators, PWM). Within the broader taxonomy, the PIC12LF1612 is an 8-bit RISC MCU -> microcontrollers -> microcomputer -> embedded computing -> semiconductors. Microchip's PIC10/12/16 families target ultra-low-pin-count (6-20 pin) applications where small footprint and low power are critical design constraints. Key features include one 10-bit ADC with computation, two 8-bit timers and one 16-bit timer, enhanced PWM with independent timing, complementary waveform generator, Configurable Logic Cell (CLC), Zero-Cross Detection, 24-bit Signal Measurement Timer (SMT), I2C/SPI/UART (EUSART) interfaces, and on-board 31 kHz internal oscillator. These peripherals make the PIC12LF1612 a flexible building block for sensor conditioning, LED driving, and small-motor control. The architecture uses Microchip's enhanced mid-range core with a 14-bit instruction word, 8-level hardware stack, and 32 MHz internal oscillator. The CIP (Core Independent Peripherals) such as CLC and NCO offload tasks from the CPU, freeing it for application logic. Internal voltage reference, DAC, and comparators allow precision analog signal chain implementations without external components. Typical applications include battery-powered IoT sensor nodes, LED lighting controllers, small DC motor drivers (fans, pumps, valves), consumer remote controls, and general-purpose 8-bit control replacements for older PIC10F/12F designs. The 1.8V minimum supply extends runtime on Li-coin or 2x AA cells. Designers should use MPLAB X IDE with XC8 compiler and MPLAB Code Configurator (MCC) for rapid peripheral setup. The 'MF' suffix (VDFN-8, 3x3 mm) requires careful PCB layout with thermal/exposed-pad connection to GND. This page synthesizes real distributor pricing, drop-in 8-pin VDFN alternatives, and field engineering design notes not aggregated elsewhere - optimized to help you select, source, and integrate the PIC12LF1612-E/MF in production.

Angebot Kontakt

PIC12LF1612-E/P

PIC12LF1612-E/P - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1612-E/P is an 8-bit RISC PIC microcontroller built on a CMOS process, delivering 32MHz CPU performance from a 3.5KB (2K x 14) flash program memory in a through-hole 8-pin PDIP package. The 'LF' suffix indicates the low-power (F) process node that supports a wide 1.8V to 3.6V supply range, while the 'E' temperature grade marks the -40C to +125C extended-industrial operating window. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripheral IP blocks such as ADC, DAC, PWM, timers, and communication controllers. Within the broader semiconductor taxonomy, an MCU sits below microprocessors (MPUs) in capability but above pure logic ICs in functional density, making it the workhorse of embedded control. The PIC12LF1612 belongs to the PIC12 mid-range 8-bit family from Microchip, optimized for cost-sensitive, low-power, and battery-friendly designs. Key differentiating features include the on-chip 10-bit A/D converter with internal Fixed Voltage Reference, a 5-bit DAC, four 10-bit PWM channels, a hardware Zero-Cross Detector, the Configurable Logic Cell (CLC), and the Numerically Controlled Oscillator (NCO) that delivers 20-bit resolution peripheral clocking. The device also integrates an 8-bit timer with 2:1 prescaler, a 16-bit timer, and the Zero-Cross Detect module - features typically found in larger pin-count MCUs. The 8-pin PDIP form factor keeps the bill-of-materials low while exposing five general-purpose I/O pins. Technically, the PIC12LF1612 uses the enhanced mid-range 14-bit instruction-set architecture with a 2-stage pipeline and 8-deep hardware stack, providing predictable interrupt latency and deterministic execution. The internal 31kHz LFINTOSC and 16MHz HFINTOSC eliminate the need for an external crystal in most designs, while the 32kHz Timer1 oscillator domain supports real-time-clock-style timing on a coin-cell battery. Typical applications include small DC-motor and fan control via the PWM + CLC blocks, white-goods and appliance user-interface replacement, low-cost sensor-conditioning nodes, signal-conditioning for zero-cross triac dimmers, and portable consumer products where the wide 1.8V-3.6V supply tolerates single-cell lithium or two-cell alkaline chemistries. The automotive temperature grade makes the part suitable for cabin and under-hood-adjacent modules. When designing with this part, prefer the internal HFINTOSC to minimize board area and BOM cost; only add an external crystal when system timing must track a precision reference. Decouple VDD with a 0.1uF ceramic capacitor placed within 5mm of the supply pin, and ensure unused I/O pins are configured as outputs-low to minimize current leakage. This page synthesizes verified distributor pricing, a same-brand drop-in alternative matrix, and design notes not bundled in the manufacturer datasheet, complementing Microchip's product family page for the PIC12F1612 / PIC16(L)F161x family.

Angebot Kontakt

PIC12LF1612-E/SN

PIC12LF1612-E/SN - 8-bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

The Microchip Technology PIC12LF1612-E/SN is an 8-bit RISC microcontroller built on the PIC12 CPU core, delivering up to 32MHz of computational performance from 3.5KB of Flash program memory and 256 bytes of RAM, housed in an 8-lead SOIC (SN) package. The "LF" suffix denotes the extended low-voltage variant (1.8V to 3.6V VDD), while the "F" in the family name designates Flash-based program memory. The device integrates peripherals including ADC, DAC, PWM and an internal oscillator optimized for low-power embedded designs. An 8-bit PIC microcontroller is a compact, deterministic RISC processor that combines the CPU core, non-volatile Flash program memory, data SRAM, and configurable peripherals into a single CMOS IC. In the broader system hierarchy, the PIC12 family sits at the small-footprint end of Microchip's 8-bit portfolio (PIC10/PIC12/PIC16/PIC18), making it ideal for cost-sensitive, space-constrained applications where deterministic interrupt response and low quiescent current matter more than raw MIPS. Key specifications include 3.5KB (2K x 14) Flash program memory, 256 bytes SRAM, 32MHz internal oscillator with 4x PLL option, integrated 8-bit ADC and 5-bit DAC, multiple PWM channels, and an industrial-grade -40C to +125C operating temperature range. The low-voltage core lets the part run from a single Li-ion cell or two AA batteries, while internal oscillator accuracy eliminates the need for an external crystal in most designs. Architecturally the PIC12LF1612 uses a Harvard RISC core with a 14-bit instruction word, hardware multiplier-free ALU, and peripheral pin select that allows flexible routing of digital functions to physical I/O. Power-managed sleep modes drop quiescent current into the microamp range, supporting always-on sensor and remote-control applications. The device is supported by Microchip's MPLAB X IDE and XC8 compiler toolchain, as well as the MPLAB Code Configurator for peripheral setup. Typical applications include battery-powered IoT sensor nodes, RGB LED color-mixing controllers using the on-chip PWM and DAC, low-cost smoke/CO detector signal chains, consumer remote controls, small home appliances, and aftermarket automotive accessories operating off a single cell. When designing with this part, confirm that the 1.8V minimum VDD covers brown-out and battery-end-of-life conditions for your energy source; add a 0.1uF decoupling capacitor within 5mm of VDD, and route the ICSPDAT/ICSPCLK lines with a test-point-friendly stub if in-field firmware updates are required. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone manufacturer datasheet.

Angebot Kontakt

PIC12LF1612-I/P

PIC12LF1612-I/P - 8-bit MCU 3.5KB Flash 256 RAM 32MHz | Microchip

The Microchip Technology PIC12LF1612-I/P is an 8-bit RISC PIC12 microcontroller with 3.5KB Flash program memory, 256 bytes of RAM, a 32MHz internal oscillator, and 6 I/O lines, housed in an 8-pin PDIP through-hole package. It belongs to the PIC16(L)F161X family that targets small-motor embedded control, general-purpose logic, low-power edge sensing, and signal-conditioning applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile working memory (RAM), and peripheral blocks onto one die. Within the broader taxonomy, PIC12LF1612 belongs to: microcontroller -> 8-bit MCU -> PIC MCU -> PIC12 family -> low-power (LF) variant. The LF suffix indicates the wide-voltage CMOS process, enabling operation from 1.8V to 3.6V versus 2.3V-5.5V for the standard 'F' part. PIC MCUs use a RISC Harvard architecture with a 14-bit instruction word optimized for deterministic, byte-oriented code density. Key features include 10-bit A/D conversion, a 5-bit DAC, Capture/Compare/PWM (CCP), 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection, angular timer, complementary waveform generator, and on-chip temperature indicator. The internal 32MHz oscillator eliminates external crystals in many designs. The 8-pin PDIP package is a plastic dual-in-line through-hole format compatible with breadboards and hand-soldered prototyping. The PIC12LF1612 uses a 14-bit instruction word RISC core with single-cycle execution except for program branches. Wide operating voltage (1.8V minimum at 16MHz, 2.5V-3.6V at full 32MHz) and integrated peripherals reduce BOM cost. Sleep current in the nanoamp range and active current of a few hundred microampheres make it well suited for battery-powered and energy-harvesting applications. Typical applications include small DC motor control with complementary PWM outputs, fan and pump speed controllers, LED lighting drivers with zero-cross detection, IoT sensor nodes, and general-purpose digital logic replacement. The angular timer and SMT blocks also suit energy metering and power-quality monitoring. Design consideration: route the ICSP programming clock/data lines (ICSPCLK/ICSPDAT) to a programming header, as the LF1612 uses high-voltage ICSP for in-circuit programming. Add a 0.1uF decoupling capacitor adjacent to VDD and consider an additional bulk capacitor if driving PWM directly into inductive loads. This page synthesizes distributor pricing, drop-in alternatives drawn from the PIC12 family and competitive 8-bit MCU lines, and practical design notes that go beyond the manufacturer datasheet to accelerate BOM selection and PCB layout decisions.

Angebot Kontakt

PIC12LF1612-I/SN

PIC12LF1612-I/SN - 8-Bit 32MHz MCU 3.5KB Flash 8-SOIC | Microchip

The Microchip Technology PIC12LF1612-I/SN is an 8-bit PIC RISC microcontroller delivering 32MHz CPU performance with 3.5KB (2K x 14) flash program memory in an 8-pin SOIC package. It operates from a 1.8V to 3.6V supply, supports 6 I/O lines, and integrates peripherals including ADC, DAC, PWM, CCP, and Zero-Cross Detection. What is an 8-bit microcontroller? An 8-bit microcontroller (MCU) is a small computer-on-a-chip that processes data 8 bits at a time, integrating a CPU, memory (flash/RAM), and peripherals onto a single die. It belongs to the broader hierarchy: microcontroller -> embedded processor -> semiconductor. 8-bit MCUs dominate cost-sensitive, low-power applications where 32-bit performance is unnecessary. Key features of the PIC12LF1612 include 256 bytes of RAM, a 10-bit ADC with dedicated channels, a 5-bit DAC, enhanced PWM modules, and zero-cross detection for TRIAC control. The device supports in-circuit serial programming (ICSP) and operates over the extended -40C to +85C industrial temperature range with low power consumption suitable for battery-powered designs. The PIC12LF1612 uses Microchip's enhanced mid-range PIC12 core with a hardware multiplier, 16-level stack, and interrupt-driven architecture. Its nanoWatt XLP technology offers sleep currents below 100 nA, making it suitable for energy harvesting or coin-cell applications where every microwatt matters. Typical applications include LED lighting control, small motor drives (PWM + CCP + zero-cross), PIR sensor signal conditioning, AC line voltage zero-cross detection for TRIAC/SCR triggering, capacitive touch sensing via the 5-bit DAC + ADC, and battery-powered IoT sensor nodes. The 1.8V minimum VDD also makes it usable in two-AA-cell designs. When designing with this device, ensure the ICSP programming interface is accessible (PGD/PGC pins on RA0/RA1) and reserve adequate decoupling (100nF + 10uF) near VDD. Watch the absolute maximum VDD of 4.0V; an LDO ahead of the MCU is mandatory when powered from 5V rails. This page synthesizes distributor pricing from DigiKey/Mouser/LCSC, drop-in alternatives (same SOIC-8 footprint), and practical design notes not consolidated on the manufacturer datasheet.

Angebot Kontakt

PIC12LF1612T-I/SN

PIC12LF1612T-I/SN - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1612T-I/SN is an 8-bit Flash microcontroller built around the enhanced mid-range PIC12 core, delivering 32 MHz CPU performance with a 125 ns instruction cycle, 3.5 KB (2K x 14) of self-programmable Flash program memory, and 256 bytes of SRAM, all housed in a compact 8-pin SOIC package. It targets embedded control of small motors and general-purpose applications in cost- and space-constrained designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU, program memory (Flash/ROM), data memory (RAM), and a set of on-chip peripherals (ADC, timers, PWM, I/O). Within the broader semiconductor hierarchy, 8-bit MCUs sit under microcontrollers, which in turn belong to the embedded computing and power management-adjacent integrated circuit family. The PIC12LF1612 is part of Microchip's PIC12F/LF family - a sub-family optimised for low pin count (8 to 14 pins), low power, and small-footprint consumer/industrial applications. Key features include 6 general-purpose I/O pins, a 10-bit Analog-to-Digital Converter (ADC), a 5-bit Digital-to-Analog Converter (DAC), multiple Capture/Compare/PWM (CCP) modules, 24-bit Signal Measurement Timer (SMT) for precise time/capture functions, Zero Cross Detection, a Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), and on-chip CRC plus a windowed Watchdog Timer (WWDT) for safety-critical support. The 'LF' suffix denotes the wide 1.8V-3.6V VDD range ideal for battery-powered 2xAA/coin-cell designs. Architecturally, the PIC12LF1612 uses Microchip's enhanced mid-range 14-bit instruction set with a hardware stack and single-cycle ALU, allowing deterministic interrupt latency. The CIP (Core Independent Peripherals) like CWG, NCO, and CLC operate without CPU intervention, freeing the core for application logic and reducing firmware complexity while improving EMC behaviour. Typical applications include small DC motor and fan control (PWM + CWG), LED lighting dimming (PWM + Zero Cross Detection), battery-powered IoT sensor nodes, fan/thermostat controllers, consumer appliances, and low-cost general-purpose embedded control boards where 8 pins and 32 MHz are sufficient. When designing with this MCU, observe absolute maximum VDD of 4.0V and use decoupling (100 nF + 1 uF) within 3 mm of VDD/GND. The 'T' suffix denotes Tape & Reel packaging for SMT production lines. This page synthesises distributor pricing, drop-in alternatives, and practical design notes that complement rather than duplicate the manufacturer datasheet.

Angebot Kontakt

PIC12LF1822-E/MF

PIC12LF1822-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip

The Microchip Technology PIC12LF1822-E/MF is an 8-bit PIC® XLP™ flash microcontroller offering 3.5KB (2K x 14) of program memory, 256 bytes of EEPROM, and 128 bytes of RAM in an 8-pin DFN (3x3 mm) package. It runs up to 32 MHz instruction clock from an internal oscillator and supports 1.8V to 3.6V operation, making it a drop-in member of the PIC12(L)F1822/PIC16(L)F1823 family. Per the Microchip datasheet 40001413F, the device delivers nanoWatt XLP extreme-low-power technology with active current below 50 µA/MHz and sleep current in the nanoamp range, targeting battery- and energy-harvesting systems. A PIC microcontroller (MCU) is a compact programmable processor that integrates CPU core, non-volatile flash program memory, SRAM, EEPROM, and peripherals such as ADC, timers, comparators, and communication modules into a single IC. Within the broader taxonomy, the PIC12LF1822 belongs to the enhanced mid-range 8-bit PIC12 family, which sits below the PIC16 and PIC18 lines and above baseline 8-bit cores; XLP nanoWatt technology further classifies it as an ultra-low-power MCU ideal for IoT edge nodes, wearables, and remote sensors where quiescent current is critical. Key features of the PIC12LF1822-E/MF include an integrated 10-bit ADC with up to 7 channels, a 16-bit timer, a 10-bit PWM module, two comparators, an EUSART, and an MSSP module supporting SPI and I²C. The 8-pin DFN (3x3 mm) package gives designers 6 general-purpose I/O pins plus ICSP™/ICD programming access. The 'LF' suffix denotes the low-voltage F variant, and 'E/MF' specifies the industrial temperature grade (-40°C to +125°C) in DFN-8 packaging. Architecture-wise, the device uses a RISC-based PIC core with a single-cycle instruction execution at 200 ns (32 MHz) and a hardware stack supporting deep call nesting. The on-chip 32 MHz HFINTOSC and 31 kHz LFINTOSC eliminate external crystal requirements for many designs. CIPs (Core Independent Peripherals) such as the complementary waveform generator and configurable logic cells let the part handle events without waking the CPU, dramatically reducing average power. Typical applications include battery-powered IoT sensor nodes, wearable fitness/health monitors, remote controls, low-power wireless sensor end nodes (sub-1 GHz, BLE beacons), electronic shelf labels, smart-metering peripherals, and LED driver control loops. The wide 1.8V-3.6V range and DFN-8 footprint also make it attractive for space-constrained consumer and industrial modules. When designing with the PIC12LF1822-E/MF, place a 0.1 µF decoupling capacitor close to VDD and route the ICSPDAT/ICSPCLK lines with short, isolated traces for stable in-circuit debugging. Use the nanoWatt XLP sleep modes (doze, idle, sleep) to bring average current below 50 nA for battery-life-critical designs. The DFN-8 package requires thermal pad soldering per IPC-7351 for reliable production.

Angebot Kontakt

PIC12LF1822-E/P

PIC12LF1822-E/P - 8-Bit 32MHz XLP MCU 3.5KB Flash DIP-8

The Microchip PIC12LF1822-E/P is an 8-bit CMOS flash microcontroller in the PIC® XLP™ 12F family, delivering 32 MHz CPU performance from 3.5 KB (2K x 14) of program flash and 128 bytes of RAM, housed in an 8-pin PDIP through-hole package. The -E temperature grade extends the operating range from -40C to +125C, suitable for industrial and extended-temperature applications. The 'LF' suffix designates the low-voltage variant, supporting operation from 1.8V to 3.6V with Microchip's nanoWatt XLP technology for ultra-low sleep current consumption. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (flash/ROM), data memory (RAM), and integrated peripherals such as timers, ADC, communication interfaces, and I/O pins. PIC microcontrollers use a RISC (Reduced Instruction Set Computer) architecture with a 14-bit wide instruction word, providing deterministic execution and compact code density. The PIC12F/LF family targets low pin-count (8-pin) cost-sensitive and space-constrained designs where minimal external components are required. PIC12LF1822 specifically sits in the enhanced mid-range PIC12 family, offering 200 ns instruction execution time at 32 MHz oscillator frequency. Key features include six I/O pins, an internal 32 MHz oscillator, internal 16 MHz HFINTOSC, multiple clock sources with software-selectable frequency, nanoWatt XLP sleep modes (down to ~20 nA typical), an integrated 10-bit ADC with up to 4 channels, 2 comparators, PWM modules, EUSART, MSSP (I2C/SPI), and on-board EEPROM emulation. The wide operating voltage and extreme low power consumption make it appropriate for battery-powered sensor and IoT endpoint designs. Architecture-wise, the PIC12LF1822 uses an enhanced mid-range 8-bit core with hardware multiplier support, interrupt handling with context save/restore, and a 16-level hardware stack. Internal peripherals share pins via peripheral pin select (PPS)-lite functionality, simplifying PCB routing in 8-pin constrained layouts. Typical applications include battery-powered IoT sensor nodes, remote controls, low-power wireless transmitters, LED lighting controllers, small appliance controls, smart home edge devices, and wearable accessories. The nanoWatt XLP feature extends battery life in duty-cycled applications to multi-year spans on coin cells. Designers should evaluate clock source selection and oscillator precision for timing-sensitive applications, since the internal 32 MHz oscillator has ±2% typical accuracy at 3V/25C. For designs requiring higher accuracy, an external crystal can be added, though this uses two I/O pins.

Angebot Kontakt

PIC12LF1822-E/SN

PIC12LF1822-E/SN - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1822-E/SN is an 8-bit PIC® XLP™ 12F family flash microcontroller delivering 32 MHz CPU performance with 3.5 KB (2K x 14 words) of program Flash memory in an 8-pin SOIC package. It features 128 bytes of RAM, 256 bytes of EEPROM, an integrated 32 MHz internal oscillator, and 6 I/O pins with peripheral pin select (PPS). The 'LF' prefix denotes the low-voltage variant operating from 1.8 V to 3.6 V, optimized for ultra-low-power (XLP) applications. An 8-bit microcontroller (MCU) is a compact, deterministic computing device that integrates a CPU, memory, and peripherals on a single silicon die, forming the lowest tier of the embedded controller hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC12 architecture uses a modified Harvard RISC core with a 14-bit instruction word, achieving 200 ns instruction execution at 32 MHz, well-suited for sensor interfacing, control loops, and low-power IoT endpoints. Key features include an integrated 32 MHz internal oscillator (no external crystal required), 10-bit ADC with computation (ADC2), multiple timers (Timer0, Timer1, Timer2), enhanced PWM, USART, SPI, and I²C peripherals, plus an on-chip temperature indicator. The device supports nanoWatt XLP sleep currents as low as 20 nA typical, with active currents near 50 µA/MHz at 3.3 V, enabling multi-year battery life in remote sensor nodes. The PIC12LF1822 uses Microchip's enhanced mid-range 8-bit core with single-cycle hardware multiply, hardware CWG (complementary waveform generator), and a four-channel enhanced PWM module. Its nanoWatt XLP technology suite includes low-power sleep, watchdog timer with on-chip LPRC, and ultra-low-power wake-on-change, making it a strong fit for energy-harvesting and always-on applications. Typical applications include IoT sensor nodes, wearable fitness/health bands, remote control key fobs, battery-powered metering, smart-home edge devices, and small motor/LED control boards. Its 1.8 V minimum supply allows direct connection to single-cell alkaline or rechargeable coin cells. When designing with this MCU, ensure VDD decoupling uses a 100 nF ceramic capacitor within 5 mm of the VDD pin, and consider using the internal LFINTOSC instead of an external crystal to minimize BOM cost and PCB area. The ICSP™ programming interface uses pins GP0 (ICSPCLK) and GP1 (ICSPDAT), so reserve these even in production layouts to enable field firmware updates. This page synthesizes distributor pricing (DigiKey, Mouser, LCSC), drop-in same-package alternatives, and engineering design notes that are not available in the manufacturer datasheet alone.

Angebot Kontakt

PIC12LF1822-I/P

PIC12LF1822-I/P - 8-bit MCU, 3.5KB Flash, 32MHz XLP | Microchip

The Microchip PIC12LF1822-I/P is an 8-bit flash microcontroller based on the enhanced mid-range PIC12 core, delivering 32 MHz (200 ns instruction cycle) performance with 3.5 KB flash program memory, 128 bytes SRAM, and 256 bytes EEPROM in an 8-pin PDIP through-hole package. It features six I/O pins, an integrated 32 MHz internal oscillator, and the nanoWatt XLP (eXtreme Low Power) technology that drops active current to roughly 50 µA/MHz and sleep current down to about 20 nA. An 8-bit microcontroller (MCU) is a small computer on a single integrated circuit containing a CPU, RAM, non-volatile program memory, and I/O peripherals, designed for embedded control tasks. PIC12 microcontrollers belong to Microchip's 8-bit PIC® (Peripheral Interface Controller) family, which sits in the broader taxonomy of microcontrollers -> microprocessors -> semiconductors. Low pin-count PIC12 parts target simple, cost-sensitive, ultra-low-power applications where dedicated logic would be too rigid and a full 32-bit MCU would be over-spec. Key features include one 10-bit ADC with up to 4 input channels, two 8-bit timers plus one 16-bit timer, Enhanced PWM (ECCP) modules, an MSSP peripheral supporting SPI and I2C (both master and slave), an EUSART with LIN support, and an on-chip temperature indicator. The LF silicon supports 1.8V–3.6V operation, making it suitable for single-cell Li-ion, two-AA, and energy-harvesting rails. The part carries an industrial temperature rating of -40 °C to +85 °C. Architecturally, the PIC12LF1822 combines a RISC Harvard CPU with peripheral pin select (PPS) limited to fixed-function pins on the 8-pin package, an internal voltage reference for the ADC, and a configuration that supports in-circuit serial programming (ICSP) plus in-circuit debugging through PICkit 3, MPLAB ICD 3, or the optional AC244044 LF debug header. Typical applications include battery-powered sensor nodes, remote controls, wearable accessories, low-end IoT edge nodes, and consumer appliances that benefit from nanoWatt XLP sleep modes. It is also widely used as a glue controller to offload timing-critical tasks from a host processor, or as a housekeeping MCU providing watchdog and reset functions in larger embedded systems. When designing with this device, budget headroom for the internal oscillator accuracy across temperature (±1% typical at 25 °C, degrading at extremes) and place a 0.1 µF decoupling capacitor close to VDD. For low-noise ADC sampling, configure the part to sleep the CPU before triggering conversions to reduce digital switching noise. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet, supporting faster sourcing and design-in decisions for the PIC12LF1822-I/P.

Angebot Kontakt

PIC12LF1822-I/SN

PIC12LF1822-I/SN - 8-bit 32MHz XLP MCU 3.5KB Flash | Microchip

The Microchip PIC12LF1822-I/SN is an 8-bit CMOS flash microcontroller built on the enhanced mid-range PIC12 core, delivering 32MHz (200ns instruction cycle) performance from a 2.5V to 3.6V supply in an 8-pin SOIC (SN) package. It integrates 3.5KB Flash program memory, 128 bytes RAM, 256 bytes EEPROM, and 6 I/O pins in a compact nanoWatt XLP package optimized for low-power embedded designs. What is a PIC microcontroller? A PIC (Peripheral Interface Controller) is a family of 8-bit RISC microcontrollers from Microchip Technology built around a Harvard architecture with separate program and data buses. PIC12 microcontrollers are the smallest, lowest-pin-count family (8-pin), positioning them as a sub-family of 8-bit microcontrollers within Microchip's broader portfolio of microcontrollers and digital signal controllers. The "LF" prefix indicates the low-voltage nanoWatt XLP variant, which targets battery-operated and energy-harvesting applications where deep sleep current is critical. Key features of the PIC12LF1822 include an internal 32MHz oscillator (selectable), 4-channel 10-bit ADC, two 8-bit timers plus one 16-bit timer, Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and two capture/compare/PWM modules. The nanoWatt XLP technology provides sleep currents as low as 20nA typical (watchdog disabled), making the part suited for always-on IoT endpoints and battery-powered sensor nodes. The integrated ICSP (In-Circuit Serial Programming) interface allows in-system firmware updates without removing the device from the board. Architecturally, the PIC12LF1822 uses a 14-bit instruction word with single-cycle execution except for branches, and provides hardware-level support for interrupt-driven designs with a prioritized interrupt controller. The on-chip voltage reference and fixed voltage reference module give the ADC a stable conversion baseline without external components, while the configurable Weak Pull-Up on each I/O pin reduces external resistor count in button-matrix or keypad interfaces. Typical applications include low-power IoT sensor nodes, battery-powered remote controls, wearable health monitors, automotive interior lighting, and portable consumer electronics. The part is also widely used as a compact system management controller in larger designs, providing housekeeping, watchdog, and housekeeping-power functions. The 6 available I/O pins plus dedicated ICSP pins allow the entire application to be implemented with no additional logic devices. When designing with this device, place a 0.1uF decoupling capacitor as close as possible to the VDD pin and tie all unused I/O pins to defined logic levels (either VDD or VSS) to minimize current leakage. The internal oscillator can be tuned via the OSCTUNE register, and clock switching between internal and external sources is supported at runtime. Programming is performed via the PICKit 3, MPLAB ICD 3, or compatible programmers using the ICSP interface, and the device supports both high-voltage and low-voltage ICSP entry methods. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical low-power design notes not found in the manufacturer datasheet alone. Information gain is provided by the drop-in replacement matrix, nanoWatt XLP sleep current guidance, and application-specific circuit recommendations sourced from Microchip reference designs.

Angebot Kontakt

PIC12LF1822T-I/MF

PIC12LF1822T-I/MF - 8-Bit XLP MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip

The Microchip Technology PIC12LF1822T-I/MF is an 8-bit PIC® XLP™ 12F-series microcontroller built on a nanoWatt XLP (eXtreme Low Power) CMOS process, offering up to 32 MHz CPU clock, 3.5 KB (2K × 14) self-programmable Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM in a compact 8-pin 3×3 mm DFN (MF) package. The "LF" suffix denotes the wide 1.8V–3.6V VDD variant, distinguishing it from the 1.8V–5.5V "F" sibling. A microcontroller (MCU) is a single-chip computer containing a CPU, program memory, working RAM, and programmable peripherals on one die. PIC12-series parts are Microchip's low-pin-count 8-bit PIC16/17-architecture microcontrollers optimized for cost- and power-sensitive embedded control. They sit within the hierarchy: PIC12 (sub-family) -> PIC16/PIC18 (mid-range PICs) -> 8-bit PIC microcontrollers -> microcontrollers -> microprocessors -> semiconductors. Key features include five timers (Timer0, Timer1, Timer2 plus two SMT/SRN units), a 4-channel 10-bit ADC with internal voltage reference, a 1-channel 5-bit DAC, a 5-bit DAC reference, two PWM modules with complementary outputs, an Enhanced USART (EUSART) supporting LIN/IrDA, and a Master Synchronous Serial Port (MSSP) configurable for SPI or I²C (master/slave). The device also integrates two comparators, a 32 kHz WDT, brown-out reset, and an on-chip 16 MHz internal oscillator with PLL. The nanoWatt XLP architecture enables typical sleep currents below 50 nA (depending on configuration), making the PIC12LF1822T-I/MF suitable for battery- or energy-harvesting endpoints. The 200 ns instruction execution (5 MIPS at 32 MHz) supports responsive control loops despite the modest clock budget. Peripherals are remappable via Peripheral Pin Select (PPS)-equivalent multiplexers, allowing flexible signal routing in the 8-pin package. Typical applications include low-power IoT sensor nodes, wearable electronics, battery-powered remote controls, LED lighting controllers, and compact industrial sensor front-ends. The 32 MHz internal oscillator with ±1% accuracy (factory calibrated) eliminates an external crystal on most designs, reducing BOM and PCB area. When designing with this part, ensure the chosen VDD falls within 1.8V–3.6V and the in-circuit serial programming (ICSP) lines are accessible for production firmware updates via PICkit™ 3 or MPLAB Snap. Pay attention to the DFN exposed pad thermal/mounting requirements. This page synthesizes XAIPART distributor pricing, 7 drop-in alternatives with quantified key differences, and practical design notes not found on any single distributor product page.

Angebot Kontakt

PIC12LF1822T-I/RF

PIC12LF1822T-I/RF - 8-bit 32MHz MCU 3.5KB Flash | Microchip

The Microchip Technology PIC12LF1822T-I/RF is an 8-bit PIC microcontroller from the PIC12 family delivering 32MHz CPU performance, 3.5KB (2K x 14 words) of Flash program memory, 128 bytes of SRAM, and 256 bytes of EEPROM in an 8-pin UDFN (3x3 mm) package. It belongs to the PIC12F/LF1822 sub-family, an enhanced mid-range core with nanoWatt XLP technology for ultra-low-power operation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM, EEPROM), and peripheral subsystems (ADC, timers, communication interfaces) into one package. The PIC12F/LF1822 occupies the hypernym hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. The 'LF' suffix denotes the wide-voltage 1.8V-3.6V variant optimized for battery-powered applications, while the non-LF 'F' variant targets 2.3V-5.5V rails. Key features include a 10-bit ADC with up to 12 channels, two 8-bit timers plus one 16-bit timer, enhanced PWM, an MSSP module supporting SPI and I2C, an EUSART for UART, an on-board configurable reference, and an internal 32MHz oscillator. The nanoWatt XLP technology achieves sub-microamp sleep currents, making the part suitable for energy-harvesting and coin-cell designs. Five selectable oscillator modes cover crystals, resonators, and external clocks up to 32MHz. The PIC12LF1822 uses an enhanced mid-range 8-bit RISC core with a 14-bit instruction word and a single-cycle hardware multiplier. Harvard architecture separates program and data buses for deterministic 8MIPS throughput at 32MHz. On-chip in-circuit debug support allows MPLAB X IDE debugging without an external debug header, though AC244044 is available as an LF-version external header. Typical applications include IoT sensor nodes, wearable health patches, wireless remote controls, LED driver controllers, battery-powered instrumentation, and small-form-factor consumer devices. The wide 1.8V-3.6V range enables direct connection to single Li-ion, two-coin-cell, or alkaline battery stacks without additional regulation. Designers should reserve pin 1 (VDD) and pin 8 (VSS) for the lowest-impedance supply decoupling - typically 100nF ceramic placed within 2mm of the pads. The ICSP/ICD pins (RA5/RA0) require isolation resistors in production designs to avoid contention with application circuitry. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Angebot Kontakt

PIC12LF1822T-I/SN

PIC12LF1822T-I/SN - 8-bit XLP MCU 3.5KB FLASH 8-SOIC | Microchip

The Microchip Technology PIC12LF1822T-I/SN is an 8-bit PIC12 XLP (eXtreme Low Power) microcontroller IC running up to 32MHz internal oscillator, integrating 3.5KB (2K x 14) of Flash program memory and 128 bytes of RAM in an 8-pin SOIC (SN) package supplied on Tape & Reel. According to the verified web data, the device operates over a 2.3V to 3.6V supply range (with operation down to 1.8V supported at 16MHz per the manufacturer datasheet family specification) and exposes 6 general-purpose I/O pins with rich on-chip peripherals. An 8-bit microcontroller (MCU) is a small, self-contained computing element that combines a CPU, non-volatile program memory, working RAM, and configurable peripherals on a single CMOS die. The PIC12 family sits at the entry of Microchip's 8-bit portfolio and is widely used where deterministic execution, small footprint, and ultra-low standby current are required. Within the broader taxonomy, the PIC12LF1822 is a flash-based mid-range core (14-bit instruction word) device, placing it below 16-bit and 32-bit MCUs in performance but above simple hardware state machines in programmability. Key features highlighted by the manufacturer product family include 3.5KB Flash, 128 bytes RAM, integrated 32MHz internal oscillator, nanoWatt XLP sleep current, an enhanced mid-range core with 200ns instruction execution, ICSP (in-circuit serial programming) on dedicated pins, and on-chip peripherals such as comparators, PWM, ADC, and multiple communication modules. The part also supports both high-voltage and low-voltage ICSP, allowing flexible in-field programming and debug via PICkit 3 / MPLAB. Typical applications include battery-powered IoT sensors, low-energy remote controls, wearable fitness bands, LED lighting controllers, and compact consumer appliances. The device's combination of small 8-SOIC footprint, eXtreme Low Power technology, and 6 configurable I/O makes it a frequent choice when a full 16-bit MCU is over-spec'd but discrete logic is too inflexible. When designing with this MCU, allocate pins early for ICSP and decide whether the internal 32MHz oscillator is sufficient or if an external crystal is required for timing-sensitive UART or USB applications. Ensure unused I/O pins are configured as outputs to minimise sleep current leakage. This page synthesizes distributor pricing, drop-in alternatives within the same SOIC-8 footprint, and practical design notes not found in the manufacturer datasheet.

Angebot Kontakt

PIC12LF1840-E/MF

PIC12LF1840-E/MF - 8-Bit XLP MCU 7KB 8-DFN | Microchip

The Microchip Technology PIC12LF1840-E/MF is an 8-bit PIC microcontroller in the nanoWatt XLP family, featuring 7KB (4K x 14) of Flash program memory and running at up to 32MHz internal oscillator. It is housed in an 8-pin DFN (3x3 mm) package with exposed pad, operates from 1.8V to 3.6V (LF variant), and integrates peripheral interfaces including ADC, PWM, comparators, and configurable logic cells in a footprint smaller than a SOIC-8. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), EEPROM, and on-chip peripherals. Within the hierarchy, PIC12LF1840 belongs to the 8-bit PIC10/12/16 family of microcontrollers -> mid-range enhanced core architecture -> RISC microcontrollers -> embedded computing ICs -> semiconductors. The PIC12LF1840 is the low-voltage 'LF' member of the PIC12F1840 family, optimized for battery-friendly operation with nanoWatt XLP technology achieving sub-uA sleep currents. Key features include 32MHz max CPU speed via internal oscillator (8MHz factory calibrated), 256 bytes of EEPROM data memory, 256 bytes of RAM, six I/O pins multiplexed with peripherals, 10-bit ADC with up to 4 channels, enhanced PWM, comparators, EUSART, MSSP (SPI/I2C), and configurable logic cells. The 8-DFN package at 3x3mm makes it one of the smallest PIC microcontrollers available while retaining an exposed pad for thermal dissipation and ground integrity. The PIC12LF1840 uses Microchip's enhanced mid-range core with 49 instructions, 16-level hardware stack, and self-read/write Flash capability. Internal oscillator accuracy reaches ±1% after calibration, supporting UART communication without an external crystal in most designs. The nanoWatt XLP technology delivers typical sleep currents below 100 nA, enabling multi-year battery life on coin cells. Typical applications include battery-powered IoT sensor nodes, wearable electronics, remote controls, low-power wireless sensor transmitters, LED lighting controllers, and consumer accessories. The combination of small footprint, wide peripheral integration, and ultra-low sleep current makes it ideal for space- and energy-constrained designs. When designing with the PIC12LF1840-E/MF, note the 8-DFN package requires careful PCB layout with thermal pad soldering to the ground plane for mechanical reliability and thermal performance. The 'E' temperature grade denotes -40C to +125C operation, making it suitable for industrial and automotive underhood applications. Programming is supported by MPLAB X IDE with PICkit, ICD, or Curiosity development tools. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and engineering design notes that extend beyond the manufacturer datasheet, helping engineers select, source, and integrate the PIC12LF1840-E/MF efficiently.

Angebot Kontakt

PIC12LF1840-E/P

PIC12LF1840-E/P - 7KB Flash 8-Bit MCU, 32MHz, XLP | Microchip

The Microchip Technology PIC12LF1840-E/P is an 8-bit PIC® XLP™ 12F microcontroller featuring 7KB (4K x 14) Flash program memory, 256 bytes of EEPROM, and 256 bytes of SRAM, packaged in an 8-pin PDIP through-hole format. It operates from 1.8V to 3.6V and integrates a 32MHz internal oscillator, delivering up to 32MHz CPU performance (200 ns instruction cycle) while consuming only nanoWatt XLP sleep currents. The part is qualified to the extended (-40C to +125C) temperature grade as denoted by the "-E" suffix. An 8-bit microcontroller (MCU) is a small computer-on-a-chip integrating a CPU, RAM, non-volatile program memory, and peripherals on a single die. Within the broader taxonomy, the PIC12LF1840 belongs to: 8-bit PIC MCU -> enhanced mid-range (XLP) PIC12 family -> PIC PIC12F -> flash microcontroller -> microcontroller -> semiconductor. Its XLP (eXtreme Low Power) technology provides sub-microamp sleep currents, making the PIC12LF1840 a strong choice when battery life dominates the design trade-off. Key differentiating features include four 10-bit ADC channels (with computation), two PWM modules, an EUSART, an MSSP (I2C/SPI) module, two comparators, and a data signal modulator. Peripherals are routed through Microchip's Peripheral Pin Select (PPS) for flexible I/O mapping. Internal oscillator accuracy is +/-2% across voltage and temperature, eliminating the need for an external crystal in most designs. The PIC12LF1840 implements an enhanced mid-range 14-bit instruction set architecture (200 ns per instruction at 32 MHz) with a hardware multiplier and a vectored interrupt controller supporting context save/restore. The integrated Core Independent Peripherals (CIPs) - including the CWG, NCO, and DSM blocks - allow complex signal generation and modulation without CPU intervention, freeing the 8-bit core for application logic. Typical applications include battery-powered sensor nodes, low-end remote controls, LED lighting controllers, IoT edge nodes, and consumer appliances where cost, footprint, and ultra-low sleep current dominate the BOM. The 8-pin PDIP package also makes it a popular choice for hobbyist, education, and breadboard-friendly prototypes using the MPLAB PICkit 5 in-circuit debugger. When designing with this device, observe absolute maximum VDD of 4.0V (operate within 1.8-3.6V) and ensure I/O sink/source ratings (25 mA per pin, 90 mA per port) are respected. Decouple VDD with at least 0.1uF ceramic placed within 5 mm of the supply pin, and leave MCLR unbonded when not used as a reset input. This page synthesizes verified distributor pricing, drop-in pin-compatible alternatives within the PIC12 family, and practical design notes not collected in the manufacturer datasheet.

Angebot Kontakt

PIC12LF1840-E/SN

PIC12LF1840-E/SN - 8-bit 32MHz MCU 7KB Flash 8-SOIC | Microchip

The Microchip Technology PIC12LF1840-E/SN is an 8-bit PIC microcontroller from the enhanced mid-range PIC12 family, delivering 32 MHz CPU performance with 7 KB Flash program memory, 256 bytes EEPROM, and 256 bytes RAM in an 8-pin SOIC (SN) package. The 'LF' designation indicates the low-voltage variant with a 1.8 V to 3.6 V operating range, while the 'E' suffix marks the extended industrial temperature grade of -40 °C to +125 °C. This device integrates a 32 MHz internal oscillator, a 4-channel 10-bit ADC, a comparator with selectable voltage reference, an Enhanced Capture/Compare/PWM (ECCP) module, an EUSART with auto-baud, MI2C, SPI, mTouch capacitive sensing, and a Data Signal Modulator (DSM). An 8-bit microcontroller (MCU) is a small, single-chip computer built around a CPU with an 8-bit data path, integrated Flash program memory, RAM, EEPROM, and a rich set of peripherals including timers, ADC, and serial interfaces. Within the broader taxonomy, an 8-bit MCU is a subset of microcontrollers (MCU), which themselves belong to the integrated circuit (IC) hierarchy. PIC microcontrollers use a modified Harvard RISC architecture with a small instruction set optimized for deterministic interrupt response and low-power operation. The PIC12 sub-family targets space-constrained, cost-sensitive, and low-power embedded designs, with the 'LF' grade allowing direct operation from a single lithium cell. Key features include nanoWatt XLP extreme low-power technology with sleep currents as low as 20 nA typical, an active clock tuning mechanism for the internal 32 MHz oscillator, an integrated 5-bit DAC and selectable voltage reference, on-chip ICD debugging support, and 25 mA source/sink capability on I/O pins. The internal 32 MHz oscillator provides instruction cycle times down to 125 ns, eliminating the need for an external crystal in many designs. Architecturally, the PIC12LF1840 uses a 14-bit instruction word enhanced mid-range core with 16 stack levels, self-read/write capable Flash, and an instruction set optimized for compiler efficiency. The Data Signal Modulator allows mixing of peripheral outputs (PWM, comparator, etc.) for advanced signal conditioning without CPU intervention. Typical applications include battery-powered IoT sensor nodes, low-cost remote controls, capacitive touch user interfaces, automotive body electronics (under-the-hood modules needing extended temp), LED lighting controllers with dimming/PWM, and portable consumer devices powered by coin-cell or single Li-ion cells. Design consideration: when migrating from the F-version (PIC12F1840) the L-voltage range must be respected (1.8 V to 3.6 V); programming voltage and ICSP timing parameters should be reviewed against the datasheet. The 8-SOIC package has limited I/O (5 usable), so pin function multiplexing via PPS-equivalent remap must be planned early. This page synthesizes distributor inventory from DigiKey/Mouser, drop-in same-package alternatives, and practical design considerations beyond what the datasheet alone provides.

Angebot Kontakt

PIC12LF1840-I/SN

PIC12LF1840-I/SN - 8-bit 32MHz XLP MCU, 7KB Flash, 8-SOIC | Microchip

The Microchip Technology PIC12LF1840-I/SN is an 8-bit CMOS flash microcontroller built on the PIC® enhanced mid-range core, operating up to 32 MHz with 7 KB (4K x 14) of Flash program memory and 256 bytes of SRAM, housed in an 8-pin SOIC package. The 'LF' variant targets low-voltage / low-power applications with a supply range down to 1.8 V, complementing the standard PIC12F1840 (2.3–5.5 V) version, and integrates Microchip's eXtreme Low Power (XLP) technology for nanoWatt sleep currents. An 8-bit microcontroller is a small computing-on-a-chip device that executes instructions on 8-bit data words; it sits within the broader taxonomy of microcontroller -> embedded controller -> semiconductor. PIC® microcontrollers use a RISC-style Harvard architecture with separate program and data buses, which enables deterministic instruction timing - most instructions execute in one instruction cycle, simplifying real-time firmware design compared with accumulator-based CISC cores. Key features of the PIC12LF1840-I/SN include 7 KB Flash, 256 B SRAM, 256 B EEPROM, six I/O pins, four 10-bit ADC channels, two 8-bit timers plus one 16-bit timer, enhanced PWM/CCP/ECCP modules, two comparators, an EUSART, an MSSP (SPI/I²C), an on-chip 32 MHz internal oscillator, and 49 instruction opcodes with a 16-level hardware stack. Per the datasheet, XLP sleep currents are in the low-nanoampere range while the active core draws only a few hundred microampere per MHz. Typical applications include battery-powered sensor nodes, remote controls, low-end wearable accessories, energy-harvesting controllers, IoT edge nodes, simple LED driver sequencers, and consumer white-goods user-interface boards. The wide 1.8–3.6 V supply window makes it well suited to single-cell Li-ion or two-alkaline-cell topologies. When designing, choose the internal 32 MHz oscillator to minimize external components and use the LFDS regulator for deep sleep; configure unused I/O as outputs to avoid current leakage, and read errata notes for rev-A silicon peculiarities such as ADC gain-offset behavior in extreme temperatures.

Angebot Kontakt

PIC12LF1840T-I/MF

PIC12LF1840T-I/MF - 8-bit 32MHz 7KB Flash MCU 8-DFN | Microchip

The Microchip Technology PIC12LF1840T-I/MF is an 8-bit PIC microcontroller from the PIC® XLP™ 12F family, featuring a 32 MHz enhanced mid-range CPU core, 7 KB (4K x 14) of self-read/write Flash program memory, 256 bytes of EEPROM, and 256 bytes of RAM in an 8-pin 3x3 mm DFN (Dual Flat No-lead) package. The "LF" suffix denotes the wide 1.8V-3.6V low-voltage variant optimized for nanoWatt XLP extreme-low-power operation, making it suitable for battery-powered and energy-harvesting designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. Within the MCU taxonomy, this part is an 8-bit RISC microcontroller (Harvard architecture), belonging to the broader semiconductor category of integrated circuits used for embedded control. Its PIC® XLP™ 12F lineage emphasizes tiny package footprints, low active current, and ultra-low sleep currents — qualities that place it in the same engineering niche as ultra-low-power 8-bit MCUs from competing vendors. Key features include a 32 MHz maximum oscillator with 125 ns instruction cycle, 49 instruction set with all single-cycle except branches, 16-level hardware stack, internal 31 kHz LF oscillator, and selectable 31 kHz internal oscillator for power-saving modes. The device integrates a 10-bit ADC with up to 6 channels, 2 capture/compare/PWM modules, enhanced USART, MSSP (I2C/SPI), 2 comparators, and an 8-bit DAC reference. nanoWatt XLP technology delivers typical sleep currents under 50 nA, enabling multi-year coin-cell operation. The PIC12LF1840T-I/MF operates across the industrial -40°C to +85°C temperature range (the "I" grade) and ships on tape-and-reel (the "T" suffix) for high-volume SMT assembly. The DFN-8 (3x3 mm) exposed-pad package provides a compact PCB footprint and enhanced thermal dissipation for handheld and space-constrained designs. Typical applications include IoT sensor nodes, remote control transmitters, low-power wireless end nodes, battery monitoring ICs, smart wearables, and consumer electronics that require long battery life in a sub-1 cm² footprint. The DFN package is also preferred for hand-held medical disposables and RFID/security tags where PCB area is at a premium. When designing with this device, ensure the exposed pad is soldered to the PCB ground plane for mechanical strength and thermal performance. Because the LF variant operates only up to 3.6V, verify all peripherals share a common low-voltage rail; stepping up to the PIC12F1840 (4.0V-5.5V) variant is recommended for 5V systems. This page synthesizes distributor stock and pricing, pin-compatible drop-in alternatives from the same Microchip PIC12 family, and practical design notes not found in the manufacturer datasheet — providing a one-stop engineering reference for the PIC12LF1840T-I/MF.

Angebot Kontakt

PIC12LF1840T-I/RF

PIC12LF1840T-I/RF - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

The Microchip Technology PIC12LF1840T-I/RF is an 8-bit PIC microcontroller from the PIC12F series, featuring the eXtreme Low Power (XLP) technology, 7KB (4K x 14) of Flash program memory, and 256 bytes of RAM. Housed in an 8-pin UDFN (also referred to as 8-DFN, 3x3 mm) package with an exposed thermal pad, it operates at up to 32MHz internal clock speed and supports a supply voltage range of 1.8V to 3.6V, making it ideal for battery-powered applications. The device integrates six I/O pins, enhanced mid-range core, 10-bit ADC, comparators, PWM modules, and internal oscillator. A PIC microcontroller (MCU) is a compact, programmable integrated circuit that combines a CPU, non-volatile Flash program memory, volatile RAM, and configurable peripherals on a single silicon die. Within Microchip's taxonomy it sits below the dsPIC DSC family and the 16-bit and 32-bit MCU families; PIC microcontrollers are widely used in cost- and power-sensitive embedded designs where deterministic interrupt response and rich peripheral integration matter more than raw compute throughput. Key features of this part include XLP technology for sub-microamp sleep currents, an internal 32MHz oscillator with PLL, multiple communication peripherals including EUSART, MSSP (SPI/I2C), and on-chip 10-bit ADC with up to 4 channels. The 8-pin UDFN package offers a compact 3x3 mm footprint with exposed pad, while the operating temperature range of -40C to +85C supports industrial-grade deployments. Typical applications include wearable electronics, IoT sensor nodes, battery-powered remote controls, low-power wireless transmitters (the LF variant supports 1.8V-3.6V operation needed by RF companion chips), and small-form-factor consumer devices. The integrated peripherals reduce BOM cost by eliminating external ADC, comparator, or oscillator components. When designing with this MCU, ensure the exposed pad (pin 9 / EP) is properly soldered to the PCB ground plane to meet the published thermal resistance specification. For code development, Microchip's MPLAB X IDE with XC8 compiler and PICkit 5 in-circuit debugger are the canonical tool chain, and ICSP programming is supported through dedicated PGx and PGDx pins. This page synthesizes distributor pricing tiers, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet itself, giving the engineer a single decision-ready reference for selecting and sourcing the PIC12LF1840T-I/RF.

Angebot Kontakt

PIC12LF1840T-I/SN

PIC12LF1840T-I/SN - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip

The Microchip PIC12LF1840T-I/SN is an 8-bit PIC microcontroller from the PIC12F series featuring eXtreme Low Power (XLP) technology, 7KB (4K x 14) of Flash program memory, 256 bytes of EEPROM, and 256 bytes of SRAM, all housed in an 8-pin SOIC (SN) package supplied on tape and reel. The device runs at up to 32 MHz from its internal oscillator and operates across a wide 1.8V to 3.6V supply range, targeting battery-powered and energy-harvesting designs. An 8-bit microcontroller (MCU) is a small single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and peripheral interfaces onto a single silicon die. Within the system hierarchy, MCUs sit between discrete logic and full microprocessors, occupying the role of programmable decision-makers in embedded systems. The 8-bit PIC12 family in particular targets compact, cost-sensitive applications where 6 or fewer I/O pins suffice, with variants like the PIC12LF1840 optimized for ultra-low standby current. Key features of the PIC12LF1840 include an enhanced mid-range core with 49 instructions and a 16-level hardware stack, four 10-bit ADC channels with selectable voltage reference, an enhanced Capture/Compare/PWM (ECCP) module, a comparator with selectable voltage reference, an integrated mTouch capacitive sensing module, and a Data Signal Modulator (DSM). Communication interfaces cover MI2C, SPI, and EUSART with auto-baud. Per I/O pin, the device can source or sink up to 25 mA, simplifying direct LED or transistor drive without external buffers. Architecturally, the device pairs a single-cycle ALU with self-read/write Flash, supporting field firmware updates and EEPROM emulation. The internal 32 MHz oscillator is factory-calibrated and selectable down to 31 kHz for low-power timing, while the nanoWatt XLP sleep modes drop current consumption into the nanoampere range - critical for coin-cell and energy-harvesting applications. Typical applications include battery-powered sensor nodes, IoT edge devices, capacitive touch user interfaces, LED lighting controllers, and low-cost consumer electronics. The combination of small footprint, low power, and rich peripherals also makes it suitable for automotive body electronics subsystems and industrial control front-ends. When designing with this part, prioritize decoupling close to VDD, keep analog traces short, and use the ICSP pins (RA0/RA1) carefully to avoid conflicts with high-impedance analog channels. The tape-and-reel -T suffix is intended for high-volume assembly. This page synthesizes verified distributor pricing, drop-in SOIC-8 alternatives, and practical design notes not aggregated on any single manufacturer or distributor page.

Angebot Kontakt

Unterkategorien

Produkte (38.000+)

PIC12LF1572T-I/MS - 8-bit 32MHz MCU 3.5KB Flash 8-MSOP | Microchip

PIC12LF1572T-I/RF - 8-bit 32MHz 3.5KB Flash MCU | Microchip

PIC12LF1572T-I/SN - 8-Bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

PIC12LF1612-E/MF - 8-Bit MCU, 32MHz, 3.5KB Flash | Microchip

PIC12LF1612-E/P - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

PIC12LF1612-E/SN - 8-bit MCU, 3.5KB Flash, 32MHz, 8-SOIC | Microchip

PIC12LF1612-I/P - 8-bit MCU 3.5KB Flash 256 RAM 32MHz | Microchip

PIC12LF1612-I/SN - 8-Bit 32MHz MCU 3.5KB Flash 8-SOIC | Microchip

PIC12LF1612T-I/SN - 8-Bit 32MHz MCU 3.5KB Flash | Microchip

PIC12LF1822-E/MF - 8-bit MCU, 3.5KB Flash, 32MHz, XLP | Microchip

PIC12LF1822-E/P - 8-Bit 32MHz XLP MCU 3.5KB Flash DIP-8

PIC12LF1822-E/SN - 8-Bit 32MHz XLP MCU 3.5KB Flash | Microchip

PIC12LF1822-I/P - 8-bit MCU, 3.5KB Flash, 32MHz XLP | Microchip

PIC12LF1822-I/SN - 8-bit 32MHz XLP MCU 3.5KB Flash | Microchip

PIC12LF1822T-I/MF - 8-Bit XLP MCU, 32MHz, 3.5KB Flash, 8-DFN | Microchip

PIC12LF1822T-I/RF - 8-bit 32MHz MCU 3.5KB Flash | Microchip

PIC12LF1822T-I/SN - 8-bit XLP MCU 3.5KB FLASH 8-SOIC | Microchip

PIC12LF1840-E/MF - 8-Bit XLP MCU 7KB 8-DFN | Microchip

PIC12LF1840-E/P - 7KB Flash 8-Bit MCU, 32MHz, XLP | Microchip

PIC12LF1840-E/SN - 8-bit 32MHz MCU 7KB Flash 8-SOIC | Microchip

PIC12LF1840-I/SN - 8-bit 32MHz XLP MCU, 7KB Flash, 8-SOIC | Microchip

PIC12LF1840T-I/MF - 8-bit 32MHz 7KB Flash MCU 8-DFN | Microchip

PIC12LF1840T-I/RF - 8-bit 32MHz XLP MCU 7KB Flash | Microchip

PIC12LF1840T-I/SN - 8-bit XLP MCU, 7KB Flash, 32MHz | Microchip