Microcontroladores

Productos (19.000+)

PIC18F2455-I/SO - 48MHz 8-bit FS-USB MCU, 24KB Flash | Microchip
PIC18F2455-I/SO

PIC18F2455-I/SO - 48MHz 8-bit FS-USB MCU, 24KB Flash | Microchip

The Microchip Technology PIC18F2455-I/SO is a high-performance 8-bit PIC18 family flash microcontroller with integrated Full-Speed USB 2.0, 24KB of Flash program memory, 2048 bytes of RAM, and 256 bytes of EEPROM, packaged in a 28-pin SOIC (SO) wide-body plastic SMD outline. It operates from 4.2V to 5.5V and supports clock rates up to 48MHz, delivering up to 16 MIPS of processing throughput using the enhanced PIC18 instruction set with 200ns minimum instruction cycle. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (ROM/Flash), data memory (RAM), peripherals, and I/O onto one silicon die. Within the broader semiconductor taxonomy, an MCU belongs to the microcontroller family -> embedded processor -> integrated circuit. The PIC18 family is Microchip's enhanced mid-range 8-bit architecture, sitting above the baseline PIC16 family and offering more peripherals, more memory, and higher code efficiency, while still targeting cost-sensitive and deterministic real-time designs. Key features of the PIC18F2455 include 25 digital I/O pins, a 10-bit Analog-to-Digital Converter (ADC) with up to 11 input channels, an enhanced USART (EUSART) supporting LIN master/slave, a Master Synchronous Serial Port (MSSP) configurable as I2C or SPI up to 10 Mbit/s, a Full-Speed USB 2.0 device peripheral (12 Mbit/s) with on-chip transceiver, two analog comparators, and nanoWatt power management with multiple idle/sleep modes. It also provides three 16-bit timers/counters, two PWM modules with Capture/Compare/PWM (CCP) and Enhanced CCP (ECCP), and an 8-bit parallel slave port. Architecturally the PIC18F2455 uses a RISC-style Harvard bus architecture with separate program and data paths, 16-bit opcodes, and an 8-level hardware stack. The integrated USB SIE handles CRC, NRZI encoding, and endpoint management internally, eliminating an external PHY in most designs. Industrial -40C to +85C operation and 100K endurance Flash make it suitable for harsh environments. Typical applications include USB HID/CDC peripherals (custom HID game controllers, USB-to-UART bridges, PC test instruments), sensor data loggers, low-cost instrumentation, consumer electronics with USB firmware update (bootloader), industrial control nodes, and educational/hobbyist projects (Arduino-alternative, BASIC stamp replacements, USB IO boards). When designing with this part, ensure that VUSB is decoupled with a 220nF capacitor and that the USB D+/D- traces are 90-ohm differential matched. Programming is supported through ICSP (In-Circuit Serial Programming) on RB6/RB7 pins, so these must remain accessible on the PCB even in production layouts. This page synthesizes distributor pricing, drop-in SOIC-28 alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18F2455-I/SP - 8-bit 48MHz USB MCU 24KB Flash | Microchip
PIC18F2455-I/SP

PIC18F2455-I/SP - 8-bit 48MHz USB MCU 24KB Flash | Microchip

The Microchip Technology PIC18F2455-I/SP is an 8-bit PIC18 microcontroller with integrated Full-Speed USB 2.0, 24 KB of Flash program memory and 2 KB of RAM, packaged in a 28-pin SPDIP through-hole format. It operates from 4.2 V to 5.5 V, supports oscillator frequencies up to 48 MHz and delivers up to 10 MIPS of CPU throughput. The integrated nanoWatt technology reduces active and sleep current consumption for battery-powered and energy-sensitive designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals and I/O onto one IC. The PIC18 family uses a Harvard-architecture RISC core with 16-bit instruction words and 8-bit data paths, optimized for deterministic interrupt response and compact code. Within the broader hierarchy, the PIC18F2455 sits in the Microchip 8-bit PIC microcontroller line, positioned between baseline PIC10/12/16 parts and the 16-bit dsPIC/PIC24 family. Its USB 2.0 Full-Speed peripheral makes it a common bridge between embedded logic and PC hosts. Key features include 24 KB (12K x 16) of self-programmable Flash, 2 KB of RAM, 256 bytes of EEPROM, a 10-bit ADC with up to 13 input channels, two 8-bit and one 16-bit timers, two PWM modules and a 25 mA source/sink capability per I/O pin. The USB 2.0 Full-Speed transceiver supports 12 Mbit/s operation without an external crystal on some configurations, and three serial ports (USB, I²C and SPI up to 10 Mbit/s, plus EUSART for LIN) provide flexible connectivity. The CPU uses a modified Harvard architecture with hardware multiplier and a 31-level hardware stack, executing one instruction per four oscillator cycles. Integrated peripherals are mapped through a SFR-based register map, and interrupts are prioritized through a two-level scheme with shadow registers to reduce context-restore overhead. The nanoWatt power-management block supports multiple idle and sleep modes for ultra-low standby draw. Typical applications include low-cost USB peripherals, HID-class devices such as custom input devices and game controllers, industrial sensor interfaces with USB diagnostics, automotive LIN slave nodes and embedded data-acquisition front-ends. The wide operating range also suits 5 V industrial backplanes and battery chargers using the ADC for current/voltage monitoring. When designing with this part, ensure the VUSB pin is connected to VDD through an internal 3.3 V regulator when USB is active, and follow Microchip's recommended 27 pF capacitor on the VUSB node. Program the CONFIG registers correctly for the chosen oscillator mode (HS, XT or INTIO) before any code can run. This page synthesizes drop-in alternatives, designer application notes and current distributor pricing for the PIC18F2455-I/SP that are not aggregated on a single manufacturer or distributor page.

Cotización Contacto
PIC18F248-E/SO - 8-bit 40MHz MCU 16KB Flash CAN SOIC-28 | Microchip
PIC18F248-E/SO

PIC18F248-E/SO - 8-bit 40MHz MCU 16KB Flash CAN SOIC-28 | Microchip

The Microchip Technology PIC18F248-E/SO is an 8-bit CMOS flash-based microcontroller in the PIC18F family, integrating a 16KB (8K x 16) enhanced flash program memory and 768 bytes of RAM with a 10 MIPS (40 MHz) RISC core, housed in a 28-pin SOIC package. The PIC18F248-E/SO includes an integrated CAN 2.0B controller, a 10-bit ADC with up to 8 channels, and 23 digital I/O pins, making it a compact mixed-signal MCU for embedded networking. A PIC18F-series microcontroller is an 8-bit Harvard-architecture RISC MCU that uses separate program and data buses to allow simultaneous instruction fetch and data access. The "PIC" stands for Peripheral Interface Controller, originally designed by General Instrument's Microelectronics Division and now standardized across millions of industrial, automotive, and consumer devices. The PIC18F family is positioned in the higher-performance tier of 8-bit MCUs and offers enhanced flash memory, deeper instruction pipelines, and on-chip peripherals such as CAN, USB, and enhanced USART modules. Key features of the PIC18F248-E/SO include 16KB in-circuit reprogrammable flash (10,000 erase/write cycles typical), 256 bytes of EEPROM, 23 digital I/O pins with individual direction control, four timer modules, a synchronous serial port configurable for SPI or I2C, an enhanced USART, an 8-channel 10-bit ADC, and a CAN 2.0B module with three transmit and two receive buffers. The device operates from 4.2V to 5.5V across the extended -40C to +125C industrial range and supports ICSP (In-Circuit Serial Programming) plus MPLAB ICD debug. Architecturally, the PIC18F248 uses a 16-bit instruction word and an 8-bit data path, with a hardware multiplier, a 31-level deep hardware stack, and a vectored interrupt controller. The integrated CAN module offloads the bit timing and message buffering from the CPU, freeing cycles for application code. The 10-bit ADC with selectable acquisition time supports both low-power and high-throughput conversion modes. Typical applications include industrial CAN nodes (sensor hubs, motor controllers), automotive body and chassis electronics (mirrors, HVAC, lighting), building automation (BACnet/Modbus gateways), medical instrumentation, and embedded data acquisition systems. The combination of CAN, ADC, and EEPROM on a single 28-pin SOIC enables compact, low-cost networked sensor designs. When designing with this MCU, allocate decoupling capacitors (100 nF + 10 uF) close to VDD/VSS pairs and add a bulk capacitor on AVDD. Ensure the MCLR pin has a proper pull-up and decoupling network for reliable reset behavior. The extended (-E) temperature grade supports -40C to +125C operation. This page synthesizes distributor pricing, drop-in SOIC-28 alternatives from Microchip's PIC18F family, and practical design notes that complement but do not replace the manufacturer's datasheet.

Cotización Contacto
PIC18F248-E/SP - 8-bit MCU, 16KB Flash, CAN, 28-SPDIP | Microchip
PIC18F248-E/SP

PIC18F248-E/SP - 8-bit MCU, 16KB Flash, CAN, 28-SPDIP | Microchip

The Microchip Technology PIC18F248-E/SP is an 8-bit PIC18 enhanced Flash microcontroller with an integrated CAN (Controller Area Network) module, 16 KB of program Flash memory, 768 bytes of RAM, and 256 bytes of EEPROM, packaged in a 28-pin SPDIP (SP) through-hole form factor. Operating from a 40 MHz internal clock (10 MIPS instruction throughput), the device targets industrial and automotive CAN-node designs where on-chip protocol handling removes the need for an external CAN controller. The "-E" suffix designates the extended industrial temperature range of -40C to +125C, suitable for harsh-environment operation. A microcontroller (MCU) is an integrated single-chip computer containing a CPU core, program memory (Flash/ROM), working memory (RAM), non-volatile data memory (EEPROM), and a set of on-chip peripherals such as timers, communication interfaces and ADC channels. PIC microcontrollers from Microchip use a modified Harvard RISC architecture with separate program and data buses, enabling single-cycle instruction execution and deterministic interrupt latency. The PIC18F family sits in Microchip's mid-range 8-bit portfolio between the PIC16F baseline series and the PIC24F 16-bit families, offering a richer peripheral set (including CAN) at the cost of higher price per unit. Key features of the PIC18F248 include an integrated CAN 2.0B controller compliant with ISO 11898, a 10-bit Analog-to-Digital Converter (ADC) with up to 8 input channels, an enhanced USART supporting both RS-232 and RS-485 modes, a Master Synchronous Serial Port (MSSP) configurable as SPI or I2C, four timer modules, and a 10 MHz internal oscillator. The Instruction Set Architecture includes 77 instructions with an 8-bit data path and 16-bit instruction word, supporting hardware multiply. The 28-SPDIP package has a 600-mil (15.24 mm) body width for breadboard-friendly through-hole mounting. Architecturally, the PIC18F248 separates program Flash from data EEPROM so firmware updates do not affect stored calibration or configuration data. The CAN module includes hardware acceptance filters, mask registers and a dedicated DMA-free mailbox structure that offloads the CPU during bus arbitration and error handling. An on-chip In-Circuit Serial Programming (ICSP) interface and In-Circuit Debug (ICD) support enable development with MPLAB X IDE and PICkit programmers without removing the part from the board. Typical applications include automotive body and chassis ECUs (mirror controllers, seat controllers, lighting nodes), industrial CANopen and DeviceNet slave nodes, HVAC controls, sensor interface boards with CAN backhaul, and building automation fieldbus nodes. The integrated CAN peripheral eliminates the external CAN transceiver's MCU-side companion controller, reducing PCB area and BOM cost in multi-node CAN networks. When designing with this part, note that the integrated CAN module requires an external 3.3V or 5V CAN transceiver (such as MCP2551 or TJA1050) to physically interface with the bus. The internal oscillator accuracy of plus or minus 2 percent is sufficient for CAN bit-stamping when the SJW and BRP values are carefully calculated against the oscillator tolerance. Watchdog timer, brown-out reset and low-voltage programming features should be enabled in firmware for unattended CAN nodes. This page synthesizes distributor pricing, drop-in alternatives in the same 28-SPDIP footprint, and practical design notes not found in the manufacturer datasheet, supporting both prototype selection and production sourcing decisions.

Cotización Contacto
PIC18F248-I/SO - 8-bit 40MHz 16KB Flash MCU w/ CAN | Microchip
PIC18F248-I/SO

PIC18F248-I/SO - 8-bit 40MHz 16KB Flash MCU w/ CAN | Microchip

The Microchip Technology PIC18F248-I/SO is an 8-bit PIC18 family microcontroller with an integrated CAN (Controller Area Network) module, 16 KB of flash program memory, 768 bytes of RAM, and 256 bytes of EEPROM, operating at up to 40 MHz (10 MIPS) from a 28-pin SOIC wide-body package. It is part of Microchip's PIC18F248/258/448/458 family of high-performance enhanced flash microcontrollers and targets embedded designs requiring on-chip CAN connectivity for industrial and automotive networking. An 8-bit PIC microcontroller is a RISC (Reduced Instruction Set Computer) device that executes single-word instructions in a single instruction cycle (4 clock cycles), and the PIC18 family extends this with 16-bit instructions, an 8x8 hardware multiplier, a 31-level stack, and a Harvard memory architecture. The PIC18F248 sits in the PIC18 hierarchy as PIC18F2x8 -> PIC18F family -> PIC18 microcontroller -> 8-bit PIC -> MCU -> microcontroller, and the integrated CAN 2.0B module differentiates it from non-CAN PIC18F2x siblings, making it a direct fit for nodes that need to communicate on a CAN bus without an external controller. Key features include five 10-bit ADC channels (shared with digital I/O), one 8-bit and three 16-bit timers, a 10-bit PWM module, USART for serial communications, a Master Synchronous Serial Port (MSSP) supporting SPI and I2C, and Microchip's nanoWatt Technology power management with multiple low-power sleep modes. The integrated CAN 2.0B controller supports both standard (11-bit) and extended (29-bit) identifiers, with acceptance filters and masking, removing the need for an external CAN transceiver controller. Typical applications include automotive body and chassis networking, industrial CAN nodes, building automation sensors, HVAC controllers, and embedded motor-control peripherals. The 28-pin SOIC footprint is compatible with hand-soldering and through-hole rework on production boards. When designing with this device, ensure the CAN bus is terminated with 120 ohm resistors at each end of the bus and that a proper CAN transceiver (e.g., MCP2551 or TJA1050) is paired with the digital CAN controller pins. The 28-pin SOIC wide-body package supports industrial temperature grade (-40C to +85C) as indicated by the 'I' suffix. This page synthesizes distributor pricing, same-brand drop-in alternatives, and practical design notes - including pinout, ADC, and CAN bus layout guidance - that are not consolidated in the manufacturer datasheet.

Cotización Contacto
PIC18F2480-E/ML - 8-Bit 25MHz 16KB Flash MCU w/ ECAN | Microchip
PIC18F2480-E/ML

PIC18F2480-E/ML - 8-Bit 25MHz 16KB Flash MCU w/ ECAN | Microchip

The Microchip Technology PIC18F2480-E/ML is an 8-bit PIC18F-family CMOS microcontroller with 16KB (8K x 16) of Flash program memory, 768 bytes of SRAM, and 256 bytes of data EEPROM, housed in a 28-pin QFN (6x6 mm) package with an exposed pad. It integrates an ECAN (Enhanced CAN 2.0B) controller, a 10-bit ADC, and Microchip's nanoWatt power-management technology for low-power operation, while running at up to 25 MHz (10 MIPS) from an internal or external oscillator. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a range of peripherals (ADC, timers, communication controllers, GPIO) into one package. The PIC18F family sits in Microchip's 8-bit performance tier, offering 16-bit-wide instructions, 8-bit data paths, and enhanced peripherals such as CAN and 10-bit ADC that target embedded control rather than pure signal processing. The PIC18F2480 is the 28-pin member of the ECAN-enabled family, balancing I/O count with small footprint for body, chassis, and sensor applications. Key features include 25 I/O pins, one UART, one SPI, one I2C, one ECAN port, six timers, six PWM channels, and a 10-bit A/D converter with up to 8 channels. The 28-QFN package exposes the die thermal pad for enhanced dissipation and suits reflow-only assembly. Self-programmability and an internal oscillator reduce external component count, while the nanoWatt technology allows deep sleep currents in the nanoampere range for battery-powered designs. Typical applications include automotive CAN nodes (body controllers, instrument clusters), industrial sensor interfaces, low-cost control boards, and any CAN/LIN-connected embedded system where a small, low-pin-count MCU with integrated CAN is required. The wide 2.0V to 5.5V operating range simplifies battery-backed designs and industrial 24V-derived rails after regulation. When designing with the PIC18F2480-E/ML, ensure the exposed pad is soldered to the PCB ground plane for thermal and electrical performance, and follow the Microchip pin-out compatibility chart when migrating between 28-pin PIC18F variants. Engineers should use the MPLAB ICD 5 or PICkit programmer for development, and the ECAN bit-timing calculator in MPLAB X for bus configuration.

Cotización Contacto
PIC18F2480-E/SO - 8-bit MCU, 16KB Flash, ECAN, 28-SOIC | Microchip
PIC18F2480-E/SO

PIC18F2480-E/SO - 8-bit MCU, 16KB Flash, ECAN, 28-SOIC | Microchip

The Microchip Technology PIC18F2480-E/SO is an 8-bit PIC18-family RISC microcontroller with 16 KB Flash program memory, 768 bytes of SRAM, and an integrated Enhanced CAN (ECAN) module, housed in a 28-pin SOIC package. It executes instructions at up to 10 MIPS from a 40 MHz oscillator and includes a 10-bit A/D converter with 8 channels, nanoWatt power management, and 25 digital I/O pins. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, non-volatile program memory, RAM, and peripherals such as timers, communication interfaces, and analog-to-digital converters onto a single die. Within the broader taxonomy, 8-bit MCUs sit below 16-bit and 32-bit devices in computational throughput but above pure digital logic in integration density, making them the dominant choice for cost-sensitive embedded control. The PIC18 family specifically targets C-compilable, high-performance 8-bit designs with peripheral-rich silicon. Key features include 16 KB self-programmable Flash (8K x 16 words), 768 bytes of RAM, 256 bytes of EEPROM, hardware ECAN 2.0B controller with acceptance filters, nanoWatt technology for ultra-low-power sleep modes (down to sub-microampere), and a 10-bit ADC with 8 input channels. The instruction set is highly orthogonal and C-friendly, and the device supports in-circuit serial programming (ICSP) plus in-circuit debug via ICD. The PIC18F2480 architecture uses a 16-bit instruction word with an 8-bit data path, a hardware multiplier for 8x8 single-cycle operations, and four priority-level nested interrupts. It is built on a low-power CMOS process with brown-out reset, watchdog timer, and wide operating voltage (2.0V-5.5V for the F-version; the -E suffix denotes the extended -40C to +125C temperature range). Typical applications include automotive ECAN nodes, industrial CAN-based sensor networks, building automation, HVAC controls, and CAN-to-UART bridges. The integrated ECAN peripheral eliminates the need for an external CAN controller, reducing BOM cost and PCB footprint in distributed control systems. When designing with this part, place a 100 nF decoupling capacitor adjacent to each VDD/VSS pin pair and a 10 uF bulk capacitor near the regulator output. The ECAN bus requires a 120 ohm termination at each end of the bus and an isolated CAN transceiver such as the MCP2551 for proper differential signaling. This page synthesizes distributor inventory, parametric drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet, helping engineers evaluate the PIC18F2480-E/SO for new designs and legacy maintenance scenarios.

Cotización Contacto
PIC18F2480-E/SP - 8-Bit 25MHz MCU, 16KB Flash, ECAN, 28-SPDIP
PIC18F2480-E/SP

PIC18F2480-E/SP - 8-Bit 25MHz MCU, 16KB Flash, ECAN, 28-SPDIP

The Microchip Technology PIC18F2480-E/SP is an 8-bit RISC microcontroller from the PIC18F family, delivering 25 MIPS performance from a 40 MHz internal clock while integrating 16 KB of Flash program memory, 768 bytes of RAM, and 256 bytes of EEPROM in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It features an integrated ECAN (Enhanced Controller Area Network) module, a 10-bit A/D converter with up to 8 channels, nanoWatt power management, and 25 digital I/O pins capable of driving LED loads directly. The wide 4.2 V to 5.5 V operating range targets industrial and automotive-grade applications. According to the manufacturer datasheet, the ECAN module is fully CAN 2.0B active-compliant with hardware filtering, making this MCU a strong fit for distributed node designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, working RAM, I/O peripherals, and often analog or communication blocks on one piece of silicon. The 8-bit class is the oldest and most widely deployed MCU tier, prized for deterministic instruction timing, low cost, and robust toolchain support. Within the broader taxonomy, the PIC18F2480 sits as: MCU -> 8-bit microcontroller -> PIC18 family -> PIC18F2xxx sub-family (28/40/44-pin enhanced Flash with ECAN), optimized for CAN-bus nodes and sensor aggregation. Key features include 25 MIPS throughput at 40 MHz, hardware ECAN 2.0B with acceptance filtering, 10-bit ADC with up to 8 channels, dual analog comparators, 1 Capture/Compare/PWM (CCP) plus 1 Enhanced CCP (ECCP), 2 UART modules, MSSP for SPI/I2C, and nanoWatt technology that drops I/O leakage below 1 µA in sleep modes. The high-endurance Flash supports 100K erase/write cycles minimum, and the 28 SPDIP package simplifies through-hole prototyping and field-replaceable designs. Architecturally, the PIC18F2480 uses an enhanced Harvard architecture with separate program and data buses, a hardware multiplier, and a priority-based interrupt controller with two latency options. The instruction set is largely orthogonal and supports C compilers (XC8) for portable firmware. The ECAN engine handles bus arbitration and acceptance masks in hardware, freeing the CPU from bit-banging and enabling higher-level protocol stacks such as CANopen or DeviceNet. Typical applications include automotive body electronics, industrial CAN sensor nodes, HVAC controls, building automation gateways, distributed I/O over CAN, and small appliance motor controllers. In particular, the ECAN module plus the 10-bit ADC make it well suited to sensor-hub designs that report telemetry to a central ECU. When designing with this part, mind the E (extended) temperature grade (-40 °C to +125 °C) versus the I grade (-40 °C to +85 °C) and ensure your PCB layout respects ECAN bus isolation. In noisy environments, add common-mode chokes and TVS protection on the CANH/CANL lines per ISO 11898-2. This page synthesizes distributor pricing, drop-in PIC18F family alternatives, and practical ECAN design notes that go beyond the manufacturer datasheet to help engineers select, source, and deploy the PIC18F2480-E/SP efficiently.

Cotización Contacto
PIC18F2480-I/SO - 8-bit 40MHz MCU 16KB Flash 28-SOIC | Microchip
PIC18F2480-I/SO

PIC18F2480-I/SO - 8-bit 40MHz MCU 16KB Flash 28-SOIC | Microchip

The Microchip PIC18F2480-I/SO is a 28-pin 8-bit PIC microcontroller built on the enhanced PIC18 RISC architecture with ECAN (CAN 2.0B active) peripheral support, 16 KB of Flash program memory, 768 bytes of RAM and 256 bytes of EEPROM, running at up to 40 MHz (10 MIPS) in an industrial-grade 28-SOIC package. The -I suffix denotes an industrial operating temperature range of -40C to +85C, the /SO suffix designates the 28-lead 300-mil SOIC package, and key peripherals include an integrated ECAN bus controller, a 10-bit A/D converter with up to 8 channels, Enhanced CCP, two USARTs, MSSP (SPI/I2C), nanoWatt power management and an internal 31 kHz to 8 MHz oscillator. An 8-bit MCU is a microcontroller whose datapath, registers, ALU and program memory are organised around an 8-bit data width; the PIC18 family in particular implements an enhanced Harvard architecture with 16-bit opcodes and an 8-bit data bus, placing it in the broader hierarchy of microcontroller -> embedded controller -> semiconductor. The PIC18F2480 sits within the PIC18F2x80 device family alongside the PIC18F2580, PIC18F4480 and PIC18F4580, which differ mainly in pin count (28 vs. 40/44) and CAN peripheral count; this 28-pin member is the smallest-footprint variant of the family. Key features include 25 digital I/O pins, two analog comparators, a master synchronous serial port (MSSP) configurable as SPI or I2C, hardware ECAN supporting CAN 2.0B active (bit rates up to 1 Mbit/s), a 10-bit 8-channel ADC, four timer modules and nanoWatt Technology for reduced sleep current (as low as sub-1 uA typical). The 40 MHz oscillator yields 10 MIPS throughput, and on-chip in-circuit debug (ICD) plus two Enhanced Capture/Compare/PWM modules make it well-suited for closed-loop control. Typical applications include industrial CAN nodes such as HVAC controllers, automotive body modules, sensor networks, building-automation gateways, industrial sensors and instrumentation. The industrial temperature grade and ECAN peripheral make the part a strong fit for factory-floor networked equipment where the PCB footprint must remain small. When designing in this MCU, place VDD/VSS bypass capacitors within a few millimetres of the supply pins and avoid routing the high-speed CANH/CANL traces through the oscillator region; reserve pin 1 (MCLR) for an in-circuit debug header unless the application does not require ICD.

Cotización Contacto
PIC18F2480-I/SP - 8-Bit 40MHz MCU, 16KB Flash, ECAN | Microchip
PIC18F2480-I/SP

PIC18F2480-I/SP - 8-Bit 40MHz MCU, 16KB Flash, ECAN | Microchip

The Microchip Technology PIC18F2480-I/SP is an 8-bit PIC microcontroller running at 40 MHz, with 16 KB (8K x 16) of Flash program memory, 768 bytes of RAM and 256 bytes of EEPROM, housed in a 28-pin SPDIP (0.300 inch, 7.62 mm) through-hole package. It integrates the ECAN (Enhanced Controller Area Network) module, a 10-bit A/D converter with up to 8 input channels, nanoWatt power management and the standard PIC18 enhanced instruction set with 77 instructions and 16-bit opcode width. An 8-bit microcontroller (MCU) is a programmable system-on-chip that integrates a CPU, non-volatile program memory, working RAM, peripheral set and I/O in a single silicon die. The PIC18 family is a high-performance 8-bit architecture positioned between the baseline PIC10/12/16 series and the 16-bit dsPIC/PIC24 line; within Microchip's portfolio it sits in the "enhanced" tier offering C-friendly code, hardware multiplier and self-programming Flash. Microcontrollers sit under the broader "embedded computing" hierarchy: MCU -> microcontroller -> embedded processor -> semiconductor -> integrated circuit. Key features include 25 digital I/O pins, three 16-bit timers (Timer0/1/3) plus Timer2, two capture/compare/PWM (ECCP + CCP) modules, an enhanced USART with LIN support, MSSP for SPI/I2C, two analog comparators and a master synchronous serial port. The integrated ECAN controller with CAN 2.0B active compliance makes the part distinctive among PIC18 devices. NanoWatt technology offers multiple idle/sleep modes and on-the-fly oscillator switching for reduced quiescent current. The PIC18F2480 uses a Harvard architecture with separate program and data buses, a hardware 8x8 multiplier for fast math, a 10-bit 8-channel ADC with acquisition timer, and priority interrupt handling for time-critical events. The ECAN module supports 8 acceptance filters, programmable bit rates up to 1 Mbps, and three transmit buffers. Instruction cycle time is 4 oscillator periods, yielding 100 ns per instruction at 40 MHz. Typical applications include industrial CAN-bus nodes (e.g., sensor aggregation, distributed I/O, building automation), automotive body and comfort ECUs (mirror controllers, HVAC modules), embedded CAN bridges, OBD-II telemetry interfaces, and low-cost networked sensor nodes that benefit from the integrated CAN physical-layer signaling rather than an external controller. The 28-pin SPDIP package supports hand-soldering and breadboard-friendly prototyping that surface-mount alternatives cannot. When designing with this part, allocate at least 4 I/O pins for ICSP (PGC/PGD, MCLR/Vpp, Vss/Vdd) and respect the ECAN bus termination (120 ohm at each end of the bus). The internal 8 MHz oscillator can drive 40 MHz via the 5x PLL, eliminating an external crystal in cost-sensitive designs. This page synthesizes cross-distributor pricing, drop-in package-compatible alternatives, and practical ECAN design notes not consolidated in the manufacturer datasheet alone.

Cotización Contacto
PIC18F2480T-I/ML - 8-bit 40MHz 16KB Flash MCU 28-QFN | Microchip
PIC18F2480T-I/ML

PIC18F2480T-I/ML - 8-bit 40MHz 16KB Flash MCU 28-QFN | Microchip

The Microchip Technology PIC18F2480T-I/ML is an 8-bit PIC18 microcontroller running at up to 40 MHz with 16 KB of Flash program memory (8K x 16), 768 bytes of RAM, and 256 bytes of EEPROM, housed in a 28-pin QFN (6x6 mm) package with exposed thermal pad. This enhanced-Flash PIC18 device integrates a 10-bit ADC, CAN module, and nanoWatt power management. An 8-bit microcontroller (MCU) is a small computer built around an 8-bit data bus and Harvard or modified-Harvard architecture, integrating CPU, non-volatile program memory, working RAM, and a rich set of peripherals on a single die. Within the Microchip portfolio, the PIC18 family sits above the baseline PIC16 family in computational performance and instruction-set richness while still retaining the deterministic, single-cycle 8-bit ALU that PIC microcontrollers are known for. PIC18F2x80/4x80 sub-family devices in particular add an integrated CAN 2.0B controller, making them a frequent choice for industrial and automotive-networked embedded designs. Key features include 25 digital I/O pins, an active-high MCLR reset, ICSP/ICD in-circuit serial programming/debug, four timer modules (Timer0/1/2/3), a 10-bit A/D converter with up to 8 channels, an ECAN module, nanoWatt power-saving modes, and an extended -40C to +85C industrial temperature range. The 28-QFN (6x6) package with exposed pad improves thermal dissipation compared to the legacy 28-pin PDIP/SOIC options. The PIC18F2480 implements the enhanced PIC18 instruction set (16-bit wide instructions, 8-bit data path), supports two prioritized interrupt vectors, and provides self-programmable Flash under firmware control. Its nanoWatt technology reduces quiescent current in sleep modes below 1 uA, enabling battery-friendly field installations. Typical applications include CAN-node industrial sensor nodes, automotive body and chassis modules, motor-control front-ends, embedded data-acquisition systems, and CAN-based building-automation controllers. The combination of integrated CAN, 10-bit ADC, and ample Flash makes it well suited to networked embedded designs. When designing with this device, remember to include proper decoupling (100 nF + 10 uF) near VDD/AVDD/VSS and that the exposed thermal pad of the QFN package should be soldered to a copper pad tied to ground for mechanical and thermal performance. This page consolidates distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, giving engineers a single point of reference for PIC18F2480T-I/ML selection and qualification.

Cotización Contacto
PIC18F248T-I/SO - 16KB Flash 8-bit MCU 40MHz 28-SOIC | Microchip
PIC18F248T-I/SO

PIC18F248T-I/SO - 16KB Flash 8-bit MCU 40MHz 28-SOIC | Microchip

The Microchip Technology PIC18F248T-I/SO is an 8-bit PIC18 family RISC microcontroller featuring 16KB (8K x 16) of Flash program memory, 768 bytes of RAM, and a 40 MHz maximum operating frequency in a 28-pin SOIC wide-body package. The 'T' suffix denotes Tape & Reel packaging and the 'I' suffix indicates an industrial-grade operating temperature range of -40C to +85C. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (typically Flash), data memory (RAM), and peripherals onto a single silicon die. PIC microcontrollers use a modified Harvard RISC architecture with a 16-bit instruction word, achieving up to 10 MIPS at 40 MHz. Within the broader taxonomy, the PIC18F248 belongs to the PIC18F family -> PIC microcontrollers -> 8-bit MCUs -> microcontrollers -> integrated circuits (ICs). The device family supports C and assembly development with Microchip's MPLAB X IDE and the XC8 compiler. Key features of the PIC18F248T-I/SO include 23 digital I/O pins, 5 channels of 10-bit analog-to-digital conversion (ADC), a Controller Area Network (CAN) module, an Enhanced Universal Synchronous/Asynchronous Receiver/Transmitter (EUSART), a Master Synchronous Serial Port (MSSP) supporting SPI and I2C, and Nanowatt power management with multiple idle and sleep modes. The integrated CAN controller makes this part particularly distinctive, as the PIC18F248 was specifically designed for embedded networking applications. The architecture combines a RISC CPU with hardware multiply, 8-bit-wide data paths, and a 16-bit instruction set. The 10 MIPS throughput at 40 MHz enables real-time signal processing in industrial control loops. The internal RC oscillator and PLL options reduce external component count, while the In-Circuit Serial Programming (ICSP) and In-Circuit Debug (ICD) interfaces support field-upgradeable firmware through a standard 2-wire programming protocol. Typical applications include CAN node endpoints in industrial automation, automotive body and chassis ECUs, HVAC controls, sensor interfacing with 10-bit ADC, and embedded networking bridges. The combination of CAN, ADC, and digital I/O in a single 28-pin SOIC package simplifies PCB design and BOM for cost-sensitive networked embedded systems. When designing with this part, ensure the CAN bus transceiver is selected to match bus speed requirements; the PIC18F248 CAN module supports CAN 2.0B active with up to 1 Mbps bit rate. Decoupling capacitors must be placed close to VDD/AVDD pins, and unused I/O should be configured as outputs low for lowest quiescent current. This page synthesizes distributor pricing, drop-in alternatives drawn from the PIC18F family, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18F24J10-I/SP - 8-bit 40MHz PIC MCU, 16KB Flash, SPDIP-28
PIC18F24J10-I/SP

PIC18F24J10-I/SP - 8-bit 40MHz PIC MCU, 16KB Flash, SPDIP-28

The Microchip Technology PIC18F24J10-I/SP is an 8-bit RISC microcontroller from the PIC18FxxJxx family, operating at up to 40 MHz from a 2.0V to 5.5V supply, and housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. The part delivers 16 KB of Flash program memory, 1 KB of SRAM, and emulated EEPROM, while exposing 25 general-purpose I/O pins and a 10-bit ADC. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile data memory, and peripherals such as ADC, timers, and communication interfaces. Within the broader taxonomy, the PIC18F24J10 belongs to the 8-bit MCU category, itself a sub-class of microcontrollers and embedded controllers under the integrated-circuit hierarchy. It is purpose-built for cost-sensitive embedded designs where low-power nanoWatt technology, USB-friendly peripherals, and broad peripheral integration outweigh the need for a 32-bit core. Key features include an enhanced USART with LIN master/slave support, two MSSP (Master Synchronous Serial Port) peripherals capable of I2C with address masking and SPI, a 10-bit ADC with up to 10 channels, two analog comparators, and nanoWatt power management with multiple idle and sleep modes. The instruction set is an enhanced PIC18 Harvard architecture with 16-bit opcodes and an 8-bit data path, supporting C-friendly calling conventions and a hardware multiplier. Typical applications include consumer white goods, low-cost industrial sensor interfaces, automotive body controllers (LIN sub-nodes), HVAC thermostats, simple USB-to-UART bridges, and general-purpose embedded control nodes where the SPDIP-28 package is preferred for hand-soldered prototyping or through-hole assemblies. When designing with this part, plan for an external analog supply (AVDD/AVSS) routing even if the ADC is unused, and verify the maximum operating frequency derating versus VDD against the manufacturer datasheet. The I/SP industrial temperature grade supports -40C to +85C operation, which is sufficient for most non-automotive commercial environments. This page synthesizes distributor pricing, drop-in PIC18F alternatives, and practical design considerations not all bundled in the original manufacturer datasheet, providing engineers with a consolidated engineering reference.

Cotización Contacto
PIC18F24J10-I/SS - 40MHz 8-bit MCU 16KB Flash 28-SSOP | Microchip
PIC18F24J10-I/SS

PIC18F24J10-I/SS - 40MHz 8-bit MCU 16KB Flash 28-SSOP | Microchip

The Microchip Technology PIC18F24J10-I/SS is an 8-bit RISC flash microcontroller running up to 40 MHz, integrating 16 KB of on-chip Flash program memory and 1 KB of RAM in a 28-pin SSOP (Shrink Small Outline Package). It is part of the PIC18 J-series family, designed for low-cost, general-purpose embedded control with enhanced peripherals including a 10-bit ADC, two PWM modules, an enhanced USART with LIN master capability, an I2C/SPI synchronous serial port with I2C address masking, and nanoWatt power management for sleep-mode efficiency. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that combines a CPU, program memory (Flash/ROM), data memory (RAM), and peripheral interfaces on a single silicon die. The PIC18F family uses Microchip's enhanced RISC Harvard architecture, executing most instructions in one cycle for up to 10 MIPS throughput at 40 MHz. MCUs sit within the broader hierarchy: microcontroller -> embedded processor -> semiconductor -> integrated circuit, and serve as the computational heart of nearly every modern electronic product. Key features of the PIC18F24J10 include 1 k Flash endurance, emulated EEPROM via program-Flash self-write, 25 digital I/O pins, a 10-bit ADC with up to 13 input channels, two analog comparators, and a wide 2.0V to 5.5V supply voltage range that simplifies battery- and bus-powered designs. The device operates across the industrial -40C to +85C temperature range and supports in-circuit serial programming (ICSP) plus in-circuit debug (ICD) for development workflows. Architecturally, the PIC18F24J10 uses a 16-bit instruction word with an 8-bit data path, eight-level hardware stack, and hardware multiply block. The nanoWatt technology offers multiple idle and sleep modes with wake-up on interrupt, peripheral disable for leakage reduction, and an ultra-low-power timer1 oscillator, enabling years of battery life in periodic-duty applications. Typical applications include USB/HID human-interface devices when paired with an external transceiver, low-cost sensor interface boards, home appliances, motor control for small DC and stepper loads, LIN slave nodes in automotive body networks, industrial control panels, and general-purpose 8-bit embedded products where footprint, cost, and ease of programming matter. When designing with this part, verify the 2.0V-5.5V analog supply headroom for ADC reference accuracy, and consider the 1k Flash endurance for firmware-update frequency planning. For code-protection on production units, configure the appropriate configuration bits. This page synthesizes distributor pricing, parametric drop-in alternatives, and practical design notes that go beyond what the manufacturer datasheet alone provides.

Cotización Contacto
PIC18F24J10T-I/ML - 8-bit 40MHz 16KB Flash MCU 28-QFN | Microchip
PIC18F24J10T-I/ML

PIC18F24J10T-I/ML - 8-bit 40MHz 16KB Flash MCU 28-QFN | Microchip

The Microchip Technology PIC18F24J10T-I/ML is a high-performance 8-bit PIC18 RISC microcontroller delivering 40 MHz CPU speed at 3V, packaged in a 28-pin QFN (6x6 mm) with exposed thermal pad and shipped in Tape & Reel format. The device integrates 16 KB (8K x 16) of self-programmable Flash program memory, 1024 bytes of SRAM data memory, and 21 general-purpose I/O pins suitable for embedded control tasks. A microcontroller (MCU) is a single-chip computer that combines a CPU core, program memory (Flash/ROM), working RAM, and a rich set of peripherals (ADC, timers, communication ports) on one die. Within the embedded hierarchy, the PIC18 family belongs to the 8-bit microcontroller class, itself part of the broader microcontroller category under integrated circuits. The PIC18F24J10 occupies the low-power, low-cost node of that family, with a Harvard RISC architecture that executes most instructions in a single cycle, delivering 10 MIPS at 40 MHz. Key features include a 10-channel, 10-bit successive-approximation ADC for sensor and analog signal acquisition; an Enhanced USART (EUSART) with LIN master/slave capability for automotive and industrial networking; two Master SSP (MSSP) modules supporting both SPI and I2C (with address masking) for synchronous serial peripherals; four 16-bit timers/counters; and a wide operating voltage range of 2.7 V to 3.6 V. The integrated nanoWatt Technology power-management modes reduce quiescent current for battery-powered applications, and an internal 8 MHz oscillator supports operation without an external crystal. Typical applications include low-cost consumer appliances, industrial sensor nodes, automotive body controllers (LIN slave), USB-to-UART bridges when paired with an external transceiver, and small graphical HMI front-ends. The 28-QFN footprint is footprint-compatible with several PIC18F2xJ1x siblings, simplifying board-level migration across the family. Designers should provide a 0.1 µF decoupling capacitor as close as possible to each VDD/VSS pair, route the exposed pad to a continuous ground plane for thermal dissipation, and configure the Configuration bits via ICSP for oscillator, watchdog, and code-protection options before code execution. This page synthesizes distributor pricing, verified drop-in alternatives in the same 28-QFN footprint, application-specific design notes, and parametric comparisons against Microchip siblings and competitor 8-bit MCUs - information not consolidated on any single distributor page.

Cotización Contacto
PIC18F24J10T-I/SO - 8-bit 40MHz 16KB FLASH MCU 28-SOIC | Microchip
PIC18F24J10T-I/SO

PIC18F24J10T-I/SO - 8-bit 40MHz 16KB FLASH MCU 28-SOIC | Microchip

The Microchip Technology PIC18F24J10T-I/SO is an 8-bit RISC microcontroller from the PIC PIC® 18J family, featuring a maximum CPU clock of 40MHz at 3V, 16KB (8K x 16) of FLASH program memory, 1024 bytes of data RAM, and a 28-pin SOIC package (also called 28-SOIC, 7.50 mm body width). It is the Tape & Reel shipping variant of PIC18F24J10-I/SO with industrial (-40C to +85C) temperature range. The on-chip peripherals include an Enhanced USART with LIN master capability, two Master SSP modules (SPI and I2C), 5 timers, 2 PWM channels, 2 comparators, and a watchdog timer. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (FLASH/ROM), data memory (RAM), and peripheral interfaces into one device. The PIC18F family uses Microchip's enhanced 8-bit RISC architecture with a 16-bit instruction word, which is why FLASH is described in 8K x 16 organization. Within the taxonomy MCU -> 8-bit MCU -> PIC18 family -> PIC18FxxJ10 sub-family -> PIC18F24J10, this part sits in the entry-level FLASH tier optimized for low-cost, high-speed, communication-rich designs. Key features include nanoWatt Technology for power-managed idle/sleep modes, an integrated 10-bit ADC with up to 10 channels, two analog comparators with programmable reference, and self-programmable FLASH for bootloader support. The Enhanced USART supports LIN 1.2 master, RS-232, RS-485, and IrDA protocols through software configuration, while the two SSP modules can independently operate as SPI master/slave or I2C master/slave with address masking. Typical applications include LIN-based automotive body modules, low-cost sensor interfaces, small consumer appliances, USB/serial bridge replacements for legacy RS-232 designs, industrial control nodes with SPI/I2C peripherals, and battery-powered instruments that benefit from nanoWatt sleep modes. The wide operating voltage range (2.0V to 3.6V) suits 2xAA and 3.3V regulated rails. When migrating from PIC16F to PIC18F, ensure your toolchain supports the enhanced instruction set and the 16-bit instruction word alignment. The 28-SOIC footprint is pin-compatible with PIC18F2420/2520/2620 and PIC18F24K20/25K20/26K20 J-series replacements, simplifying PCB reuse.

Cotización Contacto
PIC18F24J11-I/SO - 8-bit 48MHz 16KB Flash XLP MCU | Microchip
PIC18F24J11-I/SO

PIC18F24J11-I/SO - 8-bit 48MHz 16KB Flash XLP MCU | Microchip

The Microchip Technology PIC18F24J11-I/SO is an 8-bit PIC18 J-series flash microcontroller featuring 16 KB of program memory, 4 KB of RAM, and a maximum CPU clock of 48 MHz (12 MIPS instruction throughput) in a 28-pin SOIC package, designed around the company's eXtreme Low Power (XLP) nanoWatt technology platform. Headline specifications include 16 KB Flash (8K x 16), 4 KB SRAM, 25 digital I/O pins, a 10-bit A/D converter with up to 10 channels, two analog comparators, two CCP/ECCP modules, and two I²C/SPI plus one enhanced USART communications peripheral. The device is rated for an industrial operating temperature range of -40 °C to +85 °C and a supply voltage of 4.2 V to 5.5 V. What is a PIC18 J-series microcontroller? The PIC18F J-series is Microchip's low-power, high-performance 8-bit CMOS flash MCU family using a Harvard-class RISC architecture with an 8-bit data path and a 16-bit instruction word. It sits hierarchically under 8-bit microcontroller -> flash microcontroller -> PIC18 family -> PIC18F J-series, and is targeted at cost-sensitive, low-power, mixed-signal embedded designs that need A/D conversion, PWM control, and standard serial comms in small pin-count packages. Key features include the nanoWatt XLP power-management block that adds deep-sleep and multiple idle modes with sub-µA sleep currents, Peripheral Pin Select (PPS) which allows digital peripheral I/O mapping to any device pin, an on-chip 10-bit ADC with automatic channel scanning, dual analog comparators with programmable reference, and an enhanced USART that supports RS-232, RS-485 and LIN. The 28-SOIC footprint offers a pin-compatible upgrade path to the larger PIC18F25J11/26J11/46J11/47J11 (40/44-pin) family members. Technical depth: the PIC18F24J11-I/SO is built on a high-performance flash CMOS process with a 2-stage pipeline and 200 ns minimum instruction cycle. Internal oscillator options and a 4x PLL allow flexible clocking from internal 31 kHz to 48 MHz without external crystals. PPS reduces PCB constraints by remapping peripherals, while the nanoWatt XLP block provides sleep currents below 100 nA in deep sleep, making the part suitable for battery-powered or energy-harvesting systems. Typical applications include low-power sensor interfaces, USB/HID peripherals, industrial control panels, automotive body and HVAC sub-modules, and consumer white-goods user interfaces. The wide operating voltage and integrated ADC are well suited to mixed-signal front-ends. Design consideration: because the part is a 4.2 V minimum VDD device (true of the J-series), it is not directly drop-in compatible with 3.3 V-only boards designed for the F-series; verify the rail before migrating firmware. This page synthesizes distributor pricing, drop-in alternatives, and design notes that go beyond the manufacturer datasheet, optimized for engineers sourcing PIC18F24J11-I/SO for new designs and BOM refreshes.

Cotización Contacto
PIC18F24J11T-I/SS - 16KB Flash 8-bit MCU 28-SSOP | Microchip
PIC18F24J11T-I/SS

PIC18F24J11T-I/SS - 16KB Flash 8-bit MCU 28-SSOP | Microchip

The Microchip Technology PIC18F24J11T-I/SS is an 8-bit PIC18 J-series flash microcontroller featuring 16 KB of program Flash, 4 KB of RAM, and 48 MHz (12 MIPS) CPU performance in a 28-pin SSOP package. The part operates from 4.2 V to 5.5 V supply, integrates nanoWatt XLP power management, and exposes 25 general-purpose I/O pins with Peripheral Pin Select (PPS) for flexible signal routing. Its 10-bit ADC, multiple timers, and enhanced Flash make it well suited to cost-sensitive embedded control. A flash microcontroller is a single-chip CMOS processor that combines an 8-bit CPU core, non-volatile Flash program memory, on-chip SRAM, and a rich set of peripherals. PIC18 J-series parts target low-power and high-performance 8-bit designs, introducing deep sleep mode for battery applications and PPS (Peripheral Pin Select) for remapping digital peripherals onto any GPIO. Within the broader taxonomy, this device is a microcontroller (MCU) -> 8-bit MCU -> PIC18 family -> PIC18 J-series -> flash MCU -> embedded controller. Key features include the enhanced Flash memory with self-programmability, hardware multiplier, two USART modules, two MSSP (SPI/I2C) ports, an enhanced 10-bit ADC with up to 13 input channels, deep sleep current in the nanoWatt range, and an operating temperature range of -40 C to +85 C (industrial grade, 'I' suffix). The 28-SSOP package is a 5.30 mm wide plastic shrink small-outline surface-mount format that allows pin-compatible migration across the 28/40/44-pin family variants. The CPU executes one instruction per 4 clock cycles (4T), reaching 12 MIPS at 48 MHz. The PPS module remaps digital functions such as UART, SPI and CCP signals to any GPIO, simplifying PCB layouts and letting the same firmware be ported between family members with different pin counts. nanoWatt technology delivers multiple low-power modes including deep sleep that preserves RAM while drawing microamp-level current. Typical applications include industrial consumer control (HVAC, white goods), low-power battery-powered sensors with sleep duty cycles, USB–PIC bridge designs and embedded networking, automotive body and comfort subsystems (non-safety), home automation edge nodes, and human-interface panels with displays and keypads. When designing with this MCU, ensure Vdd decoupling (100 nF + bulk) is placed within a few millimetres of the pin, that the MCLR reset circuit includes the recommended pull-up and decoupling network, and that unused I/O are configured as outputs low to minimize current draw. Program/debug via ICSP uses dedicated RG0/RG1/RB7 pins that must be reserved in the PCB layout. This page synthesizes Microchip datasheet specifications, distributor pricing, and drop-in alternatives not found in any single manufacturer document, giving procurement and firmware engineers a faster path to a validated BOM.

Cotización Contacto
PIC18F24J50-I/ML - 48MHz USB MCU 16KB Flash | Microchip
PIC18F24J50-I/ML

PIC18F24J50-I/ML - 48MHz USB MCU 16KB Flash | Microchip

The Microchip PIC18F24J50-I/ML is a low-power, high-performance 8-bit microcontroller with integrated full-speed USB 2.0 peripheral, 16 KB of Flash program memory, and 4 KB of RAM, housed in a 28-pin QFN (6x6 mm) package. It operates from a 2.0-3.6V core supply (with 4.2-5.5V USB VBUS tolerance via internal boost regulator), executes instructions at 48 MHz / 12 MIPS, and offers 25 digital I/O pins plus a 10-bit ADC with up to 13 channels. An MCU (microcontroller) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and configurable peripherals (ADC, timers, communication interfaces) on one die. The PIC18 family is Microchip's 8-bit enhanced Harvard architecture family, sitting between the baseline PIC10/12/16 line and the 16-bit PIC24/dsPIC families. USB-capable PIC18 devices like the J-series further add an internal 3.3V regulator and a charge pump that lets the MCU operate from a single 5V USB supply - eliminating an external LDO and shrinking BOM cost. Key features of the PIC18F24J50 include the integrated full-speed (12 Mbps) USB 2.0 device controller with on-chip transceiver, the nanoWatt XLP extreme-low-power sleep modes (down to sub-uA standby), 256-byte data EEPROM, two USART, two MSSP (SPI/I2C), three timers, and a 10-bit ADC with auto-acquisition. It supports up to 16 MIPS throughput and runs the same PIC18 instruction set used across the J-series, enabling code reuse with the PIC18F25J50 (32 KB) and PIC18F26J50 (64 KB). Architecturally, the J-series devices are designed for USB on a single supply: an internal boost converter generates 3.3V from VIN for the core, so a USB-powered device needs no external 3.3V regulator. The 25-pin I/O count and 28-pin QFN footprint keep the PCB area small, suiting HID-class peripherals, sensor bridges, and low-cost USB-to-UART bridges. Typical applications include USB HID peripherals (keyboards, mice, custom input devices), USB-to-UART bridges, low-power sensor data loggers, medical USB dongles, consumer-electronics accessories, and embedded learning kits (PICKit programmers, Microchip's own low-pin-count demo boards). When designing with this MCU, budget the 28-pin QFN thermal path and route the USB D+/D- pair as a 90-ohm differential with a clean ground return; the internal 3.3V regulator must see a bulk capacitor on VUSB3V3 even when USB is unused. This page consolidates distributor pricing, drop-in alternatives within the PIC18 J-series, USB design considerations, and QFN PCB layout guidance beyond what the manufacturer datasheet alone offers.

Cotización Contacto
PIC18F24J50-I/SO - 48MHz 8-Bit USB MCU 16KB Flash | Microchip
PIC18F24J50-I/SO

PIC18F24J50-I/SO - 48MHz 8-Bit USB MCU 16KB Flash | Microchip

The Microchip Technology PIC18F24J50-I/SO is an 8-bit PIC18 XLP microcontroller with integrated full-speed USB 2.0, 16KB (8K x 16) of Flash program memory and 48 MHz CPU clock, housed in a 28-pin SOIC package. Operating from 2.0V to 3.6V, the part delivers 48 MHz performance with nanoWatt XLP power management for battery-friendly designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, programmable peripherals, and I/O on one die. The PIC18 family uses an enhanced 8-bit RISC Harvard architecture with a modified Harvard memory map, designed for deterministic real-time response and low-power embedded applications. PIC18 J-series devices add a 12-bit A/D converter, USB 2.0 full-speed hardware, and the nanoWatt XLP feature set, placing this MCU in the broader category of low-power 8-bit microcontrollers. Key specifications include 16KB Flash, 3.8KB RAM, 256 bytes of EEPROM, 25 digital I/O pins, USB 2.0 full-speed (12 Mbps) with on-chip transceiver, two USART, one SPI, one I2C, a 10-bit ADC with up to 13 input channels, and a 2.5 mA constant-current source suitable for battery charging. The XLP feature set adds deep-sleep current down to nanoAmpere levels, making the device well suited to energy-harvesting and battery-backed applications. The PIC18F24J50 utilizes Microchip's enhanced PIC18 core with a 16-bit instruction word, an 8-level hardware stack, and a priority interrupt controller. The internal USB 2.0 transceiver eliminates the need for an external PHY, saving board area. With 48 MHz operation and a single-cycle 8x8 hardware multiplier, the core delivers sufficient throughput for USB, ADC, and PWM tasks simultaneously. Typical applications include USB peripherals (HID, CDC, MSD), battery-powered sensor nodes, low-cost data loggers, industrial human-machine interfaces, and consumer USB devices. The wide operating voltage range and integrated USB make the PIC18F24J50 particularly attractive for cost-sensitive USB embedded designs. When designing with this MCU, ensure that the VDDCORE pin is properly decoupled with a 10uF and 0.1uF capacitor pair, and that the USB VBUS pin follows USB 2.0 bus-powering rules. Programming is supported through ICSP and the optional USB bootloader. This page synthesizes distributor pricing, drop-in SOIC alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18F24J50-I/SS - 48MHz USB MCU 16KB Flash 28-SSOP | Microchip
PIC18F24J50-I/SS

PIC18F24J50-I/SS - 48MHz USB MCU 16KB Flash 28-SSOP | Microchip

The Microchip Technology PIC18F24J50-I/SS is an 8-bit PIC18J-series microcontroller with integrated full-speed USB 2.0, delivering up to 48 MHz (12 MIPS) performance from 16 KB of on-chip Flash program memory and 3.8 KB of RAM, housed in a 28-pin SSOP package. It operates from 2.0V to 3.6V core Vdd with 4.2V to 5.5V tolerant I/O, making it compatible with both 3.3V native and 5V-mixed analog designs. What is a PIC18 USB microcontroller? It is a low-power, high-performance 8-bit RISC microcontroller with an integrated USB 2.0 full-speed transceiver and endpoint RAM, designed to drop into embedded designs that previously required an external USB serializer. Within Microchip's taxonomy, the PIC18F24J50 belongs to the PIC18 family, then the PIC18J sub-family (3.3V core with nanoWatt XLP technology), then the PIC18F2xJ50 USB group (28/44-pin variants). Key differentiating features include nanoWatt XLP deep-sleep modes drawing as little as 20 nA, an on-chip full-speed USB 2.0 transceiver that eliminates external PHY chips, and an internal 31 kHz to 8 MHz oscillator with PLL flexibility for either low-power crystal-free operation or 48 MHz USB-accurate timing. The 10-bit ADC with up to 13 channels and the Enhanced Capture/Compare/PWM (ECCP) module support mixed-signal and motor-control peripherals without external glue logic. Typical applications include USB HID peripherals such as keyboards, mice, and game controllers, USB-to-UART bridges, low-power battery-powered sensor nodes leveraging XLP sleep modes, and industrial instrumentation with USB diagnostics ports. The 28-pin SSOP footprint suits compact handheld enclosures. When designing with this device, place the 4.7uF bulk and 0.1uF decoupling capacitors as close to Vdd/Vss pairs as possible and observe the 3.3V core voltage requirement, even when I/O lines talk to 5V logic. The internal regulator must be enabled via the CONFIG3L register or the part will not start. This page consolidates distributor pricing, drop-in SSOP-28 alternatives from the PIC18F2xJ50 family, USB-capable cross-vendor options, and practical layout notes that go beyond the manufacturer datasheet to accelerate your design.

Cotización Contacto
PIC18F24J50T-I/ML - 8-bit USB MCU 16KB Flash 48MHz QFN-28
PIC18F24J50T-I/ML

PIC18F24J50T-I/ML - 8-bit USB MCU 16KB Flash 48MHz QFN-28

The Microchip Technology PIC18F24J50T-I/ML is a low-power, high-performance 8-bit microcontroller with integrated full-speed USB 2.0, 16 KB of Flash program memory, 3.8 KB of RAM, and a 10-bit A/D converter, housed in a 28-pin QFN package with exposed pad (ML suffix). The 'T' suffix indicates Tape & Reel packaging, the 'I' is the industrial temperature grade (-40C to +85C), and 'ML' designates the 6x6 mm QFN-28 (also called VQFN-28) footprint. A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O. 8-bit MCUs like the PIC18F24J50T-I/ML are widely used in cost-sensitive embedded designs where deterministic performance, low power consumption, and simple toolchain integration are priorities. The PIC18F24J50 belongs to the PIC18 J-series family, which combines a RISC Harvard-architecture CPU with nanoWatt XLP power management, fitting into the broader taxonomy: MCU -> microcontroller -> embedded processor -> semiconductor. Key features include a maximum CPU clock of 48 MHz (12 MIPS), 25 programmable digital I/O pins, hardware USB 2.0 full-speed (12 Mbps) transceiver with on-chip transimpedance amplifier, two USART/UART modules, two SPI/I2C MSSP peripherals, 10-channel 10-bit ADC, and Deep Sleep mode for nanoWatt XLP standby. Operating voltage is 2.0 V to 3.6 V (typical 3.3 V) per the J-series datasheet. The QFN-28 EP package measures 6 x 6 mm and provides a low thermal resistance path through the exposed pad. The PIC18F24J50T-I/ML is built on an enhanced PIC18 Harvard RISC core with 16-bit instructions and 8-bit data path, supporting linear addressing up to 2 MB. Internal peripherals are mapped via SFRs and configurable for DMA-style operation with interrupt-driven context. The integrated USB SIE eliminates the need for an external PHY, simplifying USB device designs. Typical applications include USB HID/mouse/keyboard peripherals, USB-to-UART bridges, USB sensors and data loggers, low-power IoT nodes, consumer electronics, and industrial control with USB diagnostics. Designers select this part when they need USB connectivity in a small QFN footprint with low power budgets. When designing with this part, ensure the exposed pad (EP) is soldered to a sufficiently large copper pour to meet thermal and electrical ground requirements; an unsoldered EP raises junction temperature and degrades ADC accuracy. Place the USB DP/DN traces as a 90-ohm differential pair per USB 2.0 specification.

Cotización Contacto
PIC18F24J50T-I/SS - 48MHz 8-bit USB MCU 16KB Flash | Microchip
PIC18F24J50T-I/SS

PIC18F24J50T-I/SS - 48MHz 8-bit USB MCU 16KB Flash | Microchip

The Microchip PIC18F24J50T-I/SS is an 8-bit PIC18 XLP 18J microcontroller with integrated full-speed USB 2.0, 16KB Flash program memory, 3.8KB RAM, and a 10-bit ADC, packaged in a 28-pin SSOP (5.30 mm body) rated for industrial -40C to +85C operation. The part runs up to 48 MHz internal clock from a 2.15V-3.6V supply and ships in Tape & Reel packaging as the T-suffix variant. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O on one die. The PIC18 family uses Microchip's 8-bit RISC Harvard architecture with a 16-bit instruction word, delivering deterministic execution and low interrupt latency. The XLP (eXtreme Low Power) designation means nanoWatt sleep currents below 100 nA in Deep Sleep, making the PIC18F24J50 suitable for battery-powered or USB bus-powered designs where idle current matters. Key differentiating features include on-chip full-speed USB 2.0 (12 Mbps) with on-board transceiver, 25 digital I/O pins, 10-channel 10-bit ADC, two comparators, two capture/compare/PWM modules, and configurable logic cells. The Deep Sleep mode drops quiescent current to under 100 nA while retaining RAM and limited peripheral wake-up sources, an order of magnitude better than older PIC18 families. Architecturally, the PIC18F24J50 uses a modified Harvard core with a hardware multiply, 31-level stack, and peripheral pin select via PPS - typical for the J-series. The on-chip 48 MHz internal oscillator eliminates the need for an external crystal in many designs, though USB operation typically requires the precision internal oscillator to be tuned or a crystal to be attached to the primary oscillator pins. Typical applications include USB peripherals (HID, CDC, MIDI, custom class), low-power sensor nodes, USB-to-UART bridges, and consumer electronics with USB charging or data interfaces. The part is also used in industrial control boards where SSOP is preferred over QFN for hand-soldering and rework. When designing with this device, note that the USB D+/D- lines require careful PCB layout - 90 ohm differential impedance, short traces, and a common-mode choke for EMI compliance. The 3.3V rail must be capable of supplying 100 mA peak during USB packet transmission to avoid Vbus droop. This page synthesizes distributor pricing, drop-in alternatives across the PIC18 family, and practical USB design notes not found in the standalone datasheet.

Cotización Contacto
PIC18F24K20-E/ML - 8-bit PIC MCU 16KB Flash 48MHz 28-QFN | Microchip
PIC18F24K20-E/ML

PIC18F24K20-E/ML - 8-bit PIC MCU 16KB Flash 48MHz 28-QFN | Microchip

The Microchip Technology PIC18F24K20-E/ML is an 8-bit PIC18 RISC microcontroller featuring 16 KB of Flash program memory, 768 bytes of RAM, and 256 bytes of data EEPROM, packaged in a 28-pin QFN (6x6 mm) with an exposed thermal pad. It operates at up to 48 MHz clock speed across a 1.8V to 3.6V supply range, with the "-E" suffix denoting the extended -40°C to +125°C operating temperature grade. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and working memory, peripherals, and I/O onto one die. The PIC18F24K20 belongs to the PIC18 family, which sits in the broader 8-bit PIC microcontroller hierarchy under Microchip's microcontroller product line. PIC18 MCUs use an enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, optimized for deterministic real-time control and low-power operation. Key features include nanoWatt XLP (eXtreme Low Power) technology delivering sleep currents as low as 100 nA, an integrated 10-channel 10-bit ADC, multiple communication peripherals (EUSART, MSSP SPI/I2C), and 25 digital I/O pins. The device supports 64 KB of linear addressing and offers five timer modules for PWM, capture, and compare functions. Architecturally, the PIC18F24K20 uses a modified Harvard core with separate program and data buses, a hardware multiplier for 8x8 single-cycle operations, and an internal oscillator block that can be tuned across multiple frequency ranges. The XLP technology combines multiple low-power modes (Run, Idle, Sleep) with peripheral disabling for ultra-low standby current. Typical applications include industrial sensor nodes, low-power remote controls, battery-powered IoT end nodes, automotive body and interior subsystems, and consumer white goods requiring extended temperature operation. The wide operating voltage range and ultra-low sleep current make it well-suited for energy-harvesting designs. When designing with this MCU, evaluate whether your application requires more code space than the 16 KB Flash provides; the PIC18F25K20 (32 KB) and PIC18F26K20 (64 KB) are pin-compatible upgrades in the same 28-QFN package. Plan for an in-circuit serial programming (ICSP) header to enable firmware updates in the field. This page consolidates distributor pricing, drop-in alternative listings, and engineering design notes not found in the manufacturer datasheet, providing unique value for sourcing and design decisions.

Cotización Contacto