Microcontroladores

Productos (18756)

PIC18LF25K83T-I/SO - 8-Bit 64MHz 32KB Flash MCU | Microchip
PIC18LF25K83T-I/SO

PIC18LF25K83T-I/SO - 8-Bit 64MHz 32KB Flash MCU | Microchip

The Microchip Technology PIC18LF25K83T-I/SO is an 8-bit PIC18 microcontroller from the PIC XLP 18K family, delivering 64 MHz CPU performance, 32 KB of Flash program memory, and CAN bus connectivity in a 28-pin SOIC package. The "LF" prefix denotes the low-voltage variant (1.8V-3.6V), and the "T" suffix indicates tape-and-reel packaging, while "I/SO" specifies the -40C to +85C industrial temperature range and 7.50 mm SOIC-28 form factor. A microcontroller (MCU) is a single-chip computer containing a CPU, memory, and programmable I/O peripherals. The PIC18 family uses an enhanced 8-bit RISC architecture with a 16-bit instruction word, sitting in Microchip's product hierarchy as 8-bit MCU -> PIC -> microcontroller -> embedded IC. The "XLP" (eXtreme Low Power) designation indicates sleep currents as low as 60 nA with retention, making this part ideal for battery-powered applications where sleep-mode power dominates. Key features include a 12-bit ADC with Computation (ADC2) that automates Capacitive Voltage Divider (CVD) touch-sensing sequences, averaging, filtering, and threshold comparison without CPU intervention. The device integrates a CAN 2.0B module, up to 25-channel ADC, 10-bit DAC, multiple PWM/Capture/Compare modules, UART/SPI/I2C, and 2 KB of self-programmable SRAM with ECC-style read protection. The 28-pin SOIC package provides 25+ usable I/O with peripheral pin select (PPS) for flexible signal routing. This low-power, CAN-enabled architecture targets automotive body and industrial sensor nodes where deterministic real-time response and 3.3V operation matter. The ADC2 hardware-accelerated touch engine offloads button/slider scanning from the CPU, while the 64 MHz core leaves headroom for application stacks like CANopen or J1939. Typical applications include automotive body controllers, CAN sensor nodes, capacitive touch user interfaces, industrial HVAC controls, and low-power IoT sensor hubs. The wide 1.8V-3.6V supply range allows direct Li-Ion or 2x AA battery operation without a separate LDO. Design with the LF variant only on 3.3V rails; for 5V systems select the PIC18F25K83T-I/SO. Place a 100 nF decoupling capacitor within 2 mm of each VDD/AVDD pin pair and route MCLR through a 10 kohm pull-up. When migrating to the pin-compatible 40-pin PIC18(L)F45K83, no firmware changes are required - only unused I/O are simply not bonded out. This page consolidates distributor pricing, drop-in same-family alternatives, and ADC2 touch-sensing design notes not collected in any single source on the web.

Cotización Contacto
PIC18LF25K83T-I/SS - 8-Bit 64MHz 32KB Flash MCU | Microchip
PIC18LF25K83T-I/SS

PIC18LF25K83T-I/SS - 8-Bit 64MHz 32KB Flash MCU | Microchip

The Microchip PIC18LF25K83T-I/SS is an 8-bit PIC18 XLP microcontroller featuring 32KB Flash, 2KB RAM, and 1KB EEPROM, packaged in a 28-pin SSOP (5.30mm body). It operates at up to 64MHz with a C compiler-optimized RISC architecture and integrates a CAN 2.0B controller, two I2C, two SPI, and 2KB SRAM, all on a wide 1.8V to 5.5V supply rail. An 8-bit microcontroller is a single-chip computer built around an 8-bit data-path CPU; the PIC18 family from Microchip is the higher-performance tier of that category with hardware multipliers and 16-bit instructions. Within the broader taxonomy, PIC18F sits under Microcontroller -> Embedded MCU -> Integrated Circuit, and the 'LF' prefix designates the extended low-power (XLP) variants that operate down to 1.8V. The PIC18(L)F25/26K83 family specifically adds integrated CAN bus connectivity, positioning it above general-purpose 8-bit MCUs and alongside 16-bit alternatives such as dsPIC33 in Microchip's CAN-capable portfolio. The 32KB self-programmable Flash and 256-byte data EEPROM, combined with 2KB SRAM and the 12-bit ADC with Computation (ADC2), support advanced touch sensing via Capacitive Voltage Divider (CVD) techniques. Dual I2C/SPI, a CAN 2.0B controller with DMA, and a 32MHz internal oscillator remove many external components. eXtreme Low Power (XLP) technology keeps active current in the microamp range for battery-powered designs, and IDLE/DOZE modes let dynamic power track the application duty cycle. The 28-SSOP package has a compact 5.30mm body with 0.65mm pitch, suiting hand-solderable prototypes as well as volume assembly. Hardware context includes an integrated DMA controller that offloads data movement, configurable logic cells, and a peripheral pin select (PPS) that simplifies PCB routing by remapping digital peripherals to alternate pins without rewiring the board. Typical uses include automotive body and CAN nodes, industrial sensor and control modules, capacitive-touch user interfaces, low-power IoT edge nodes, and battery-powered instrumentation. A robust CAN peripheral and 12-bit ADC2 also suit medical, white-goods, and HVAC fieldbus designs where deterministic messaging and low standby power are required. When designing, allocate two-layer board area for the SSOP-28 ground pad and confirm the decouple network (typically 100nF + 1uF) is within 3mm of VDD. For CAN nodes, verify the transceiver load and bus termination against ISO 11898 and use the internal DMA to keep CPU overhead low under heavy bus traffic. This page aggregates current distributor pricing, true drop-in alternatives, and hands-on design notes for the PIC18LF25K83T-I/SS - practical information not gathered in a single place in the manufacturer datasheet.

Cotización Contacto
PIC18LF2610-I/SO - 8-bit 64KB Flash MCU, 40MHz, 28-SOIC | Microchip
PIC18LF2610-I/SO

PIC18LF2610-I/SO - 8-bit 64KB Flash MCU, 40MHz, 28-SOIC | Microchip

The Microchip Technology PIC18LF2610-I/SO is an 8-bit PIC18 flash microcontroller featuring 64 KB of program memory, 3968 bytes of RAM, and 25 digital I/O pins, operating up to 40 MHz from a 2.0-5.5 V supply in a 28-pin SOIC package. It integrates a 10-bit A/D converter with up to 11 channels, two analog comparators, two CCP/ECCP modules, a USART, an MSSP (SPI/I2C), and the standard PIC18 enhanced instruction set with 75 instructions and 83 with the extended opcode set. An 8-bit microcontroller (microcontroller) is a single-chip computer containing a CPU core, Flash program memory, RAM, non-volatile EEPROM, and a rich set of peripherals (timers, ADC, communication interfaces) integrated on one die. PIC18 is Microchip's high-performance 8-bit family, positioned above the PIC16 family by offering a 16-bit instruction word, hardware multiplier, linear memory map, and C-friendly architecture, while still maintaining the 8-bit ALU. Microcontrollers belong to the broader category of embedded controllers and are the workhorse of low-cost, low-power digital systems in industrial, automotive, and consumer products. The PIC18LF2610 is the low-voltage ('LF') variant of the PIC18F2610, allowing operation down to 2.0 V (versus 4.2 V for the 'F' version), which makes it suitable for battery-powered designs and 3.3 V systems. It carries the PIC18F2X1X/4X1X peripheral set, including nanoWatt power management with multiple idle/sleep modes and an on-chip low-voltage detect (LVD) module. The 'SO' suffix indicates a 28-pin SOIC (300-mil body) industrial temperature range (-40 to +85C) package. Typical applications include industrial control, motor control (BLDC/stepper via CCP/PWM), sensor signal conditioning (via the 10-bit ADC), USB-to-UART bridges (paired with an external UART/USB bridge IC), lighting controllers, security and alarm panels, and general-purpose 8-bit embedded control boards. The combination of ample Flash (64 KB), generous RAM, and a rich peripheral mix makes it a strong fit for firmware-rich mid-volume designs. When designing with this part, ensure the in-circuit serial programming (ICSP) pins (RB6/RB7) are brought to a programming header and that VDD decoupling uses 100 nF + bulk capacitance close to the package. Choose the 'LF' variant explicitly when the supply rail is below 4.2 V; otherwise the standard PIC18F2610-I/SO provides the same peripheral set. This page synthesizes real-time distributor pricing, cross-vendor drop-in alternatives from the Microchip PIC18F2X1X/4X1X family, and practical PCB/firmware design notes not consolidated in the datasheet alone.

Cotización Contacto
PIC18LF2610-I/SP - 8-Bit MCU, 64KB Flash, 28-SPDIP | Microchip
PIC18LF2610-I/SP

PIC18LF2610-I/SP - 8-Bit MCU, 64KB Flash, 28-SPDIP | Microchip

The Microchip Technology PIC18LF2610-I/SP is an 8-bit RISC microcontroller in the PIC18F family featuring 64KB (32K x 16) of Flash program memory, 3968 bytes of RAM, and 25 I/O pins, all housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It executes instructions at up to 40 MHz (10 MIPS) from an internal oscillator or external clock source, while supporting an extended operating voltage range of 2.0 V to 5.5 V typical, with the LF suffix indicating low-voltage operation optimized for 2.5 V, 3.3 V, and 5 V rails. The -I/SP suffix designates the industrial temperature grade (-40 °C to +85 °C) in SPDIP form factor. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path, integrating a CPU core, non-volatile program memory (Flash), volatile data memory (SRAM), peripherals, and I/O into one package. PIC18F-series parts belong to the broader PIC microcontroller family (PIC -> microcontroller -> embedded processor -> semiconductor IC). The 8-bit class remains widely deployed in cost-sensitive, low-power, deterministic-control applications where 32-bit MCUs would be over-spec and the higher unit cost unjustified. Key features of the PIC18LF2610-I/SP include nanoWatt Technology for ultra-low-power sleep modes, a 10-bit Analog-to-Digital Converter (ADC) with up to 13 input channels, multiple Enhanced USART and MSSP (SPI/I2C) peripherals, capture/compare/PWM (CCP/ECCP) modules, a hardware 8x8 multiplier, and 25 digital I/O pins with interrupt-on-change support. The architecture is Harvard, with separate program and data buses, plus a 16-bit instruction word and 8-bit data path that yield high code density. The PIC18 core is built on a modified Harvard architecture with 16-bit instruction words and an 8-bit data path, achieving up to 10 MIPS throughput. Its nanoWatt Technology supports run, idle, and several sleep modes with wake-up on interrupt, plus software-controlled oscillator switching for dynamic power/performance tuning. The integrated ADC, comparators, and PWM peripherals allow most closed-loop control tasks to be handled without external ICs. Typical applications include industrial sensor interface boards, low-power handheld data loggers, building automation controllers, automotive body-electronics modules, battery-powered instrumentation, and educational/prototyping platforms where legacy 28-pin through-hole footprints simplify assembly. The wide 2.0 V-5.5 V supply tolerance also suits solar or energy-harvesting subsystems. When designing with this MCU, ensure decoupling (100 nF plus 10 µF bulk) is placed within a few millimetres of VDD/VSS, and that MCLR is pulled high through a 10 kΩ resistor with a 100 nF cap to ground. The ISP (In-System Programming) pins require isolation resistors if the application drives them externally during programming. This page synthesizes distributor pricing, drop-in replacement options, and engineering design notes not consolidated in the manufacturer datasheet.

Cotización Contacto
PIC18LF2610T-I/SO - 8-bit 40MHz PIC MCU 64KB Flash | Microchip
PIC18LF2610T-I/SO

PIC18LF2610T-I/SO - 8-bit 40MHz PIC MCU 64KB Flash | Microchip

The Microchip Technology PIC18LF2610T-I/SO is an 8-bit PIC18F-series RISC microcontroller with a 40 MHz maximum operating frequency, 64 KB (32K x 16) of Flash program memory, and 3.8 KB of RAM, housed in a 28-pin SOIC (SO) package supplied on tape and reel. It is the LF (low-voltage/F-version) variant with a 2.0 V to 5.5 V operating range, and it integrates peripherals including I2C, SPI, UART/USART communications, a 10-bit ADC, multiple timers, and 25 I/O pins. What is a PIC18 microcontroller? A PIC18 is an 8-bit RISC microcontroller from Microchip Technology built on an enhanced Harvard architecture with 16-bit instructions. PIC18F devices sit in the middle of the Microchip 8-bit portfolio (above baseline PIC10/12/16 and below the 16-bit dsPIC/PIC24 and 32-bit PIC32 lines), combining cost-effective 8-bit processing with rich peripherals, Flash program memory, and nanoWatt power-saving modes for industrial and consumer embedded designs. Key features include 64 KB of self-programmable Flash for in-field firmware updates, 3.8 KB of data SRAM, a hardware USART supporting RS-232/RS-485, an MSSP module configurable as SPI or I2C (master or slave), a 10-bit ADC with up to 8 input channels, two 8-bit timers plus three 16-bit timers, and nanoWatt Technology with multiple idle/sleep modes for low-power battery applications. The /SO suffix indicates a wide-body 300-mil SOIC package, while the T suffix denotes tape-and-reel packaging for high-volume SMT assembly. The architecture uses a 16-bit instruction word with an 8-bit data path and a 31-level hardware stack, allowing deterministic interrupt response and C-compiler-friendly code density. The LF suffix designation extends VDD operation down to 2.0 V, making the part suitable for 2x AA battery or 3.3 V regulated-rail designs while remaining software- and pin-compatible with the standard F (PIC18F2610) variant running at 4.2 V to 5.5 V. Typical applications include industrial control modules, automotive body and HVAC subsystems, low-power sensor nodes, USB-to-serial bridges, brushless-DC motor controllers, white-goods user interfaces, and consumer appliances where a 5 V-tolerant 8-bit MCU with on-chip Flash simplifies BOM and firmware lifecycle. Designers should note that code developed for PIC18F2610 ports directly to PIC18LF21 because both share peripherals and pinout, but FFS (Fail-Safe Clock Monitor) and two-speed start-up modes behave differently in LF devices at low VDD. The 28-SOIC package has a thermal resistance theta-JA of approximately 80 C/W, so continuous 40 MHz operation at 85 C ambient requires verifying that peripheral drive current remains within Microchip derating curves. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and design notes that go beyond the manufacturer datasheet summary, giving engineers a single decision-grade reference.

Cotización Contacto
PIC18LF2680-I/SO - 8-bit 40MHz 64KB Flash MCU with ECAN | Microchip
PIC18LF2680-I/SO

PIC18LF2680-I/SO - 8-bit 40MHz 64KB Flash MCU with ECAN | Microchip

The Microchip PIC18LF2680-I/SO is an 8-bit PIC18 microcontroller with integrated Enhanced CAN (ECAN) peripheral, 64KB Flash program memory, 3328 bytes RAM, and 40 MHz maximum CPU clock speed, housed in a 28-pin SOIC (300 mil) package. The "LF" prefix denotes the low-voltage / low-power variant supporting operation down to 2.0V, making it suitable for battery-powered and portable applications while the "I" suffix indicates an industrial temperature range of -40C to +85C. An 8-bit microcontroller (MCU) is a programmable processor that executes instructions on 8-bit data words, integrating CPU, memory (Flash for program, SRAM for variables), and peripherals onto one chip. Microcontrollers sit below microprocessors in the embedded hierarchy: MCU = microprocessor core + memory + peripherals in a single IC, optimized for control rather than raw compute. Within Microchip's portfolio, the PIC18F family occupies the high-performance 8-bit tier, and the PIC18F26xx sub-family specifically adds an integrated CAN 2.0B controller for automotive and industrial networking. Key features include hardware ECAN 2.0B with acceptance filters, 10-bit ADC up to 8 channels, enhanced USART, MSSP (SPI/I2C), two analog comparators, and nanoWatt technology power management. The 64KB Flash is organized as 32K x 16 words, allowing word-aligned access. An ICD/ICSP debug port is provided for in-circuit development with MPLAB tools. Typical applications include automotive body and comfort ECAN nodes, industrial sensor buses, HVAC controllers, building automation, and CAN-based battery management. The 28-SOIC footprint provides a wide, easy-to-solder outline well-suited to hand-prototyping and through-air rework. When designing with this part, mind the 2.0V minimum VDD for LF operation, and ensure ECAN bus termination (120 ohm at each end) and proper transceiver selection such as MCP2551 or MCP2561.

Cotización Contacto
PIC18LF2680-I/SP - 8-bit MCU 64KB Flash ECAN 28-SPDIP | Microchip
PIC18LF2680-I/SP

PIC18LF2680-I/SP - 8-bit MCU 64KB Flash ECAN 28-SPDIP | Microchip

The Microchip Technology PIC18LF2680-I/SP is an 8-bit PIC18F-family Flash microcontroller with integrated ECAN (Enhanced Controller Area Network), 64KB of program Flash memory, and 3328 bytes of RAM, housed in a 28-pin SPDIP (Skinny Plastic DIP) through-hole package. It runs at up to 40 MHz CPU clock from a 2.0V to 3.6V supply, with 1 KB of dedicated EEPROM and 25 general-purpose I/O pins, plus integrated ECAN, USART, MSSP (SPI/I2C), 10-bit ADC and 4 timers. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, I/O peripherals, and sometimes communication interfaces on one die. The PIC18 family is Microchip's 16-bit instruction-word, 8-bit data-width family of RISC microcontrollers, designed for embedded control applications that demand high code density, deterministic interrupts, and low power. The 'LF' prefix denotes the low-voltage variant optimised for 2.0V to 3.6V operation, while the 'F' variant typically runs from 4.2V to 5.5V. MCUs sit at the lowest tier of the embedded-computing hierarchy: MCU -> microcontroller -> embedded controller -> semiconductor IC. Key features of the PIC18LF2680-I/SP include on-chip ECAN 2.0B active module with hardware filtering, a 10-bit ADC with up to 8 input channels, two analog comparators, two 8-bit timers and three 16-bit timers, an Enhanced Capture/Compare/PWM (ECCP) module, and nanoWatt Technology power-management modes. According to the verified distributor data, the device integrates 64KB (32K × 16) of Flash with self-programmability, 3328 bytes of SRAM, and 1KB of EEPROM. The 28-SPDIP package is the legacy through-hole footprint preferred for prototyping, education, and industrial modules that need user-replaceable parts. On the architecture side, the PIC18LF2680 uses a 16-bit wide instruction set with single-cycle ALU operations, an 8-bit data path, hardware multiply, hardware FSR registers for C-pointer access, and a 32-level hardware stack. The ECAN engine implements ISO 11898-1 compliant CAN 2.0B active with acceptance filters, time-stamping, and bus-error counters, freeing the CPU from low-level framing. Internal RC and PLL options allow the system clock to be derived from the ECAN bit-rate quanta, an important detail when designing deterministic CAN networks. Typical applications include industrial CAN-bus sensor nodes, automotive body-control and diagnostics modules, building-automation gateways, low-cost motor-control BLDC/H-bridge drivers, USB-CAN bridges, and embedded training kits where the 28-DIP package simplifies socket-based replacement. Designers also use this part for HVAC controllers, agricultural sensor transmitters, and SCADA I/O modules because of its wide industrial temperature grade and ECAN support. Design consideration: when migrating firmware between PIC18LF2680 and the PIC18F2680 (5V variant), confirm both the VDD range and the Fosc configuration bits - the 3.3V regulator must not exceed 3.6V. The legacy SPDIP package has higher thermal resistance than modern QFN alternatives, so at full 40 MHz with all peripherals active in a sealed enclosure, derate the clock or add airflow. For new designs consider the K-series PIC18F25K80 as a modern functional equivalent in SOIC/QFN. This page synthesises distributor pricing, parametric equivalents, and practical design notes not found in the standalone manufacturer datasheet.

Cotización Contacto
PIC18LF2680T-I/SO - 40MHz 8-bit MCU 64KB Flash w/ECAN
PIC18LF2680T-I/SO

PIC18LF2680T-I/SO - 40MHz 8-bit MCU 64KB Flash w/ECAN

The Microchip Technology PIC18LF2680T-I/SO is a low-power 8-bit PIC18 microcontroller built on an enhanced RISC architecture, featuring a 40 MHz CPU clock, 64 KB (32K x 16) of Flash program memory, 3328 bytes of RAM, and an integrated Enhanced CAN (ECAN) module, all housed in a 28-pin SOIC package. The "LF" prefix denotes the wide-bandgap silicon revision optimized for 2.0 V to 5.5 V operation, and the trailing "T" indicates a Tape and Reel packaging variant. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals (timers, ADC, communication interfaces) on one die. MCUs sit in the embedded computing hierarchy below microprocessors (MPUs) and above discrete logic; the PIC18 family specifically targets mid-range applications requiring deterministic real-time response, low power, and rich peripheral integration. The PIC18LF2680 is the LF (low-voltage/F-series) member, sharing its pinout and instruction set with the standard F variant but adding extended low-voltage operation. Key features include 25 I/O pins, a 10-bit Analog-to-Digital Converter (ADC) with up to 8 channels, two USART modules, an MSSP (Master Synchronous Serial Port) supporting SPI and I2C, two CCP/ECCP modules, and the Enhanced CAN 2.0B module with hardware acceptance filters. The device also provides 4 timer modules (Timer0/1/2/3), hardware 8x8 multiplication, and a 16-bit wide instruction word for compact code density. Typical applications include industrial CAN-bus nodes (sensor networks, motor drives), automotive body electronics (instrument clusters, HVAC controllers), building automation (BACnet or CANopen gateways), and embedded control boards requiring low-power sleep modes (down to microamp-level standby current via Sleep mode and ultra-low-power wake-up). When designing with this part, verify your compiler toolchain supports the PIC18F2680 silicon ID (device ID 0x0700 family). The "T" suffix denotes tape-and-reel packaging only and does not affect electrical specifications. For prototypes, prefer the PIC18LF2680-I/SO (tray) variant to avoid reel minimum-order quantities.

Cotización Contacto
PIC18LF2682-I/SO - 8-bit 40MHz MCU 80KB Flash ECAN 28-SOIC | Microchip
PIC18LF2682-I/SO

PIC18LF2682-I/SO - 8-bit 40MHz MCU 80KB Flash ECAN 28-SOIC | Microchip

The Microchip Technology PIC18LF2682-I/SO is an 8-bit RISC microcontroller from the PIC18F family with an integrated ECAN (Enhanced Controller Area Network) module, 80 KB of Flash program memory, 3.25 KB of RAM, and 1 KB of EEPROM, housed in a 28-pin SOIC (SO) wide-body package. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), non-volatile storage (EEPROM), and programmable I/O peripherals on one die. The PIC18 family is Microchip's high-performance 8-bit line, featuring a 16-bit instruction word, hardware multiplier, and 31-level stack. The "LF" prefix designates the low-voltage F-version that supports 2.0V-5.5V operation (industrial, 2.5V/3.3V/5V common rails), while the "F" (without L) version supports 4.2V-5.5V only. The PIC18LF2682 specifically adds an ECAN peripheral - CAN 2.0B with filtering and masking - making it part of Microchip's "connected" MCU tier for industrial networking. Key features include a 40 MHz maximum clock (10 MIPS instruction throughput), 34 digital I/O pins, a 10-bit ADC with up to 11 channels, two enhanced USART modules, two MSSP (SPI/I2C) ports, and four 8-bit/16-bit timers. The integrated ECAN module supports CAN 2.0B active with bus speeds up to 1 Mbit/s, DeviceNet and CANopen compatibility, and hardware acceptance filters that offload message handling from the CPU. The 28-SOIC package provides a 7.50 mm body width suited for hand-soldered prototypes and through-hole-friendly board edges. Architecturally, the PIC18LF2682 uses a Harvard RISC core with single-cycle ALU operations, a hardware 8x8 multiplier, and a C-optimizing instruction set. The ECAN engine implements the Bosch CAN 2.0B specification in hardware with 6 acceptance masks and 14 acceptance filters, enabling protocol-level filtering without CPU intervention. The internal 10-bit ADC supports both single-ended and differential conversions with sleep-mode auto-trigger for low-power sensing. Typical applications include industrial CAN-bus nodes (sensor aggregation, motor control status reporting), automotive body and chassis ECUs (non-safety subsystems), building automation HVAC controllers, and embedded control boards requiring 5V-tolerant I/O without a separate transceiver. The wide VDD range also supports battery-backed systems running at 3.3V from a coin cell or Li-ion source. When designing with this part, ensure the CAN bus termination, biasing, and external transceiver (e.g. MCP2551 or MCP2562) are correctly matched to the ECAN TX/RX pins. Use Microchip's MPLAB X IDE with the XC8 compiler for firmware development, and confirm in-system programming via ICSP for production programming. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18LF2682-I/SP - 8-bit MCU, 80KB Flash, ECAN, 28-SPDIP | Microchip
PIC18LF2682-I/SP

PIC18LF2682-I/SP - 8-bit MCU, 80KB Flash, ECAN, 28-SPDIP | Microchip

The Microchip Technology PIC18LF2682-I/SP is an 8-bit RISC enhanced flash microcontroller with integrated ECAN (Enhanced Controller Area Network) and a 10-bit A/D converter, packaged in a 28-pin SPDIP (Skinny Plastic DIP) through-hole form factor. The device integrates 80KB of flash program memory, 3KB of SRAM data memory, and 1KB of EEPROM data memory, executing instructions at up to 10 MIPS from a 40 MHz internal clock. The LF prefix denotes the wide-voltage variant operating from 2.0V to 5.5V (with ECAN active at 4.2V to 5.5V), making it suitable for both 3.3V and 5V designs. What is an 8-bit PIC18 microcontroller? It is a member of Microchip's PIC18 family of Harvard-architecture microcontrollers, positioned in the hierarchy as PIC18 -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. PIC18F/LF parts combine a RISC instruction set, nanoWatt Technology power management, and rich peripheral integration (CAN, ADC, PWM, USART, SPI, I2C) into a single chip, replacing discrete logic in embedded applications. The 'F' suffix denotes flash program memory and the 'L' in 'LF' denotes the low-voltage / wide-Vdd variant. The '2682' family specifically targets ECAN-enabled industrial and automotive networking. Key features include 25 I/O pins, two enhanced USART modules, one MSSP (SPI/I2C), one ECAN module, one 10-bit ADC with up to 11 input channels, two CCP/ECCP modules, and nanoWatt power management with multiple idle and sleep modes. The 28-pin SPDIP package offers through-hole mounting for prototyping, breadboarding, and industrial designs where through-hole robustness is preferred over surface-mount. The industrial temperature range of -40C to +85C supports harsh-environment deployment. Architecturally, the PIC18LF2682 uses a 16-bit instruction word with 8-bit data path, providing orthogonal addressing and a hardware multiplier for 8x8 single-cycle operations. The ECAN module implements CAN 2.0B active with 32 acceptance filters and eight acceptance mask registers, supporting bit rates up to 1 Mbps for high-speed CAN networks. nanoWatt Technology reduces quiescent current to below 100 nA in sleep mode, enabling battery-backed industrial sensors. Typical applications include CAN node interfaces in industrial automation, automotive body and chassis ECUs, building automation gateways, HVAC controllers, sensor hubs with local processing, and CAN-based distributed I/O modules. The 28-pin SPDIP package is also favored for educational boards and engineering prototypes. When designing with this part, note that the LF variant supports 2.0V to 5.5V supply while ECAN requires a minimum of 4.2V. Plan decoupling with 100 nF ceramic close to VDD and a 10 uF bulk capacitor at the supply rail. Use ICD/ICSP headers for in-circuit debugging with Microchip's MPLAB X IDE and PICkit 3/4 or ICD 4 programmers. This page synthesizes distributor pricing, drop-in PIC18LF2682 alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18LF2682T-I/SO - 8-Bit 40MHz MCU 80KB Flash | Microchip
PIC18LF2682T-I/SO

PIC18LF2682T-I/SO - 8-Bit 40MHz MCU 80KB Flash | Microchip

The Microchip Technology PIC18LF2682T-I/SO is an 8-bit PIC18F-family microcontroller with 40 MHz max CPU speed, 80 KB (40K x 16) of FLASH program memory, 3.25 KB of RAM, and 1 KB of EEPROM, housed in a 28-pin SOIC (0.295", 7.50 mm width) wide-body package. The "LF" prefix denotes the low-voltage F variant, optimized for 2.0 V to 3.6 V operation from a single Li-ion cell or 3.3 V regulated rail, while the "T" suffix indicates Tape & Reel packaging for high-volume assembly. What is a PIC18 microcontroller? PIC18 is Microchip's high-performance 8-bit MCU family using an enhanced RISC architecture with a 16-bit instruction word and 8-bit data path, sitting above the baseline PIC16 family in the Microchip taxonomy: PIC10/12/16 (baseline) -> PIC18 (mid-range enhanced) -> PIC24/dsPIC (16-bit) -> PIC32MX (32-bit MIPS) -> PIC32MZ (32-bit ARM-class). The PIC18 line is widely deployed in automotive body, industrial control, and consumer applications because it balances deterministic 8-bit peripherals (CAN, ADC, PWM, I2C/SPI) with a mature, low-cost toolchain (MPLAB X IDE, XC8 compiler). Key features include 25 digital I/O pins, an internal oscillator, a 10-bit ADC with up to 8 channels, an ECAN module for Controller Area Network communications, dual analog comparators, dual USART, MSSP (SPI/I2C), and capture/compare/PWM modules. The 28-SOIC wide package provides hand-solder-friendly leads and generous thermal mass for industrial environments, with an operating temperature range of -40C to +85C. Architecturally, the PIC18LF2682 uses a 16-bit modified Harvard bus with a 31-level hardware stack and 8x8 hardware multiply, enabling 40 MIPS performance from a single-cycle instruction execution at 40 MHz. On-chip peripherals like ECAN and the 10-bit ADC share dedicated DMA-free interrupt vectors, allowing deterministic response times suitable for real-time control loops. Typical applications include CAN bus node endpoints (automotive body controllers, industrial sensor hubs), low-power sensor conditioning frontends, brushed DC motor control, smart energy metering, and embedded human-machine interface panels where a 3.3 V single supply, generous flash, and proven long-term Microchip silicon longevity make it a workhorse choice. When designing with this device, allocate 1 to 2 ICSP pins and reserve a 4.7 kohm pull-up on MCLR to enable in-circuit serial programming; configure the configuration bits for the LF voltage range (2.0 V - 3.6 V) and internal oscillator to minimize external BOM cost. This page synthesizes drop-in alternatives, distributor pricing tiers, and practical design notes drawn from Microchip datasheets and reference designs, providing actionable engineering value beyond what is found in the manufacturer datasheet alone.

Cotización Contacto
PIC18LF2685-I/SP - 8-bit 40MHz 96KB Flash MCU w/ ECAN | Microchip
PIC18LF2685-I/SP

PIC18LF2685-I/SP - 8-bit 40MHz 96KB Flash MCU w/ ECAN | Microchip

The Microchip Technology PIC18LF2685-I/SP is an 8-bit RISC microcontroller from the PIC18F family, integrating 96 KB of Flash program memory, 3.25 KB of RAM, and 1 KB of EEPROM, and packaged in a 28-pin SPDIP (SP) through-hole form factor. The LF suffix designates the low-voltage F-variant core that supports an extended supply range of 2.0 V to 5.5 V, while the -I industrial temperature option guarantees operation from -40 C to +85 C. The device integrates an ECAN (Enhanced CAN 2.0B) controller, a 10-bit ADC with up to 11 channels, nanoWatt power-management technology, and a 40 MHz internal/external oscillator that yields 10 MIPS of computational throughput. An 8-bit microcontroller (MCU) such as the PIC18LF2685 is a single-chip computer based on an 8-bit data path, optimized for deterministic real-time control rather than raw throughput. Within the system hierarchy, PIC18F devices sit between PIC16F baseline controllers and dsPIC33 Enhanced Digital Signal Controllers, occupying the high-performance 8-bit tier. They are widely deployed in industrial automation, automotive body and sensor networks, and embedded control applications where ECAN, capacitive touch (mTouch via CTMU), and PWM peripherals are required. Key features include the integrated ECAN 2.0B module (compliant with CAN 2.0A/B active and passive), a 10-bit A/D converter with up to 11 input channels, two Enhanced USART modules that support LIN/IrDA, two MSSP ports configurable as SPI or I2C (Master/Slave), and nanoWatt Technology with multiple idle and sleep modes for reduced quiescent current. The instruction set is a 16-bit enhanced Harvard architecture with 75 instructions and 83 with the extended instruction set enabled. Architecturally the part uses a 16-bit program-memory bus with an 8-bit data bus, a hardware multiplier for 8x8 single-cycle operations, and a priority-level interrupt controller with both edge- and level-sensitive external sources. The wide operating voltage window of 2.0 V to 5.5 V allows direct battery connection (e.g., two or three alkaline cells) and simplifies designs that must survive load-dump transients when paired with an external regulator. Typical applications include CAN node endpoints in industrial and automotive networks, sensor-interface front ends, motor-control signal conditioning (pre-driver), HVAC controllers, and low-power battery-backed instrumentation. The combination of ECAN, nanoWatt sleep modes, and through-hole SPDIP packaging makes it a strong fit for legacy and field-serviceable embedded designs. When designing with this part, ensure the MCLR reset network (typical 10 kohm pull-up and a decoupling cap) is sized per AC/DC characteristics table. Configure the CONFIG words using MPLAB X IDE or a compatible programmer; the LF (low-voltage F) variant requires VDD above 2.0 V for Flash programming. This page synthesizes verified distributor pricing, same-package drop-in alternatives, and design notes beyond what is published in the standalone Microchip datasheet.

Cotización Contacto
PIC18LF2685T-I/SO - 8-Bit 40MHz 96KB Flash MCU | Microchip
PIC18LF2685T-I/SO

PIC18LF2685T-I/SO - 8-Bit 40MHz 96KB Flash MCU | Microchip

The Microchip Technology PIC18LF2685T-I/SO is an 8-bit PIC18 microcontroller featuring a 40 MHz RISC core, 96 KB of Flash program memory (48K x 16 words), 3.25 KB of RAM, and integrated ECAN (Controller Area Network) and 10-bit ADC peripherals, housed in a 28-pin SOIC wide-body (7.50 mm) tape-and-reel package. The "LF" prefix denotes the low-voltage F-variant core, supporting operation from 2.5V, 3.3V, and 5V rails with nanoWatt power-management technology for sleep current reduction. A PIC18 microcontroller is a member of Microchip's 8-bit PIC (Peripheral Interface Controller) family built on a Harvard-architecture RISC core. PIC18 sits above the PIC16 and PIC12 families in complexity and below the PIC24/dsPIC families in performance, targeting cost-sensitive embedded applications that need deterministic real-time control, on-chip Flash self-programmability, and rich analog/digital peripherals. The PIC18LF2685 specifically belongs to the "28/40/44-pin enhanced Flash microcontrollers with ECAN" family, designed for industrial control and CAN-connected sensor nodes. Key differentiating features of the PIC18LF2685 include its integrated ECAN module (CAN 2.0B active), 10-bit ADC with up to 11 channels, 8 MHz internal oscillator, nanoWatt power management with multiple idle/doze/sleep modes, and in-circuit serial programming (ICSP) plus in-circuit debugger (ICD) support. The 96 KB Flash supports self-programming under firmware control, useful for bootloaders and field updates. The PIC18LF2685 uses Microchip's enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path, achieving up to 10 MIPS at 40 MHz. The ECAN peripheral implements the Bosch CAN 2.0B active specification with hardware acceptance filtering, reducing CPU overhead versus bit-banged CAN stacks. Multiple timer modules (Timer0/1/2/3) provide capture, compare, and PWM capability for motor-control and waveform-generation applications. Typical applications include industrial CAN-bus sensor nodes, single-phase induction motor control (per the family datasheet title), automotive body and chassis ECUs, building automation gateways, and remote sensor monitoring. The wide 2.0V to 5.5V operating range allows direct Li-ion battery and 24V industrial bus interfacing with simple LDO pre-regulation. When designing with this device, allocate adequate decoupling (100 nF + 10 uF) close to VDD/AVDD/VSS pins and respect the ICSP pin assignments (RB6/RB7) so that in-circuit programming headers can be added without board rework. The ECAN bus requires a CAN transceiver (e.g., MCP2551 or MCP2562) since the PIC18LF2685 only contains the protocol controller, not the physical-layer transceiver. This page synthesizes distributor pricing, drop-in alternatives from the PIC18F/LF2682/2685 family, and practical design notes for the ECAN-equipped PIC18 platform that are not consolidated in the manufacturer datasheet alone.

Cotización Contacto
PIC18LF26J11-I/ML - 8-Bit 48MHz 64KB Flash MCU | Microchip
PIC18LF26J11-I/ML

PIC18LF26J11-I/ML - 8-Bit 48MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18LF26J11-I/ML is a high-performance 8-bit microcontroller from the PIC18 J-series family, featuring a 48 MHz internal clock speed, 64KB of flash program memory (32K x 16), and 3.8KB of RAM, housed in a 28-pin QFN (6x6 mm) package with exposed thermal pad. It belongs to Microchip's XLP (eXtreme Low Power) family, with the LF prefix indicating a wide operating voltage range suited to battery-powered applications. What is a PIC18 microcontroller? A PIC (Peripheral Interface Controller) is an 8-bit RISC microcontroller from Microchip Technology based on Harvard architecture with separate program and data buses. The PIC18 family is the high-end 8-bit line, supporting enhanced instruction set, larger memory (64KB+ flash), and rich peripherals (10-bit ADC, PWM, I2C/SPI/UART, USB on some variants). PIC MCUs occupy the 8-bit microcontroller taxonomy - more capable than PIC16, simpler and lower power than 32-bit ARM Cortex-M devices, and widely used in cost-sensitive industrial and consumer embedded designs. Key features include up to 34 I/O pins, 10-bit ADC, multiple communication peripherals (I2C, SPI, UART), integrated nanowatt XLP sleep modes with current consumption as low as microamps, and an enhanced flash program memory architecture supporting self-programming. The 'LF' voltage range (2.0V to 3.6V) makes it ideal for low-power applications powered by 2x AA/AAA cells. Internally, the PIC18LF26J11 uses a modified RISC core with 75+ instructions and a hardware multiplier for 16x16 bit operations in a single cycle. The 28-QFN (ML) package variant saves PCB space compared to SOIC-28 alternatives and provides better thermal dissipation through the exposed pad for higher-frequency continuous operation. Typical applications include battery-powered sensor nodes, USB peripherals (in the F version of this family), industrial control modules, consumer electronics human-machine interfaces, and portable medical devices. The wide memory and rich peripherals also suit automotive body controllers and home appliances with user interfaces. When designing, note that programming requires Microchip's MPLAB X IDE plus an ICD programmer/debugger (e.g., PICkit, ICD 3/4). The QFN-6x6 ML package needs careful PCB land pattern routing - the exposed pad must be soldered to a sufficient copper pour for thermal dissipation. This page synthesizes distributor pricing, drop-in PIC18 alternatives in the same 28-QFN footprint, and practical design notes not found on the manufacturer product page alone.

Cotización Contacto
PIC18LF26J11-I/SO - 8-Bit 48MHz 64KB Flash XLP MCU | Microchip
PIC18LF26J11-I/SO

PIC18LF26J11-I/SO - 8-Bit 48MHz 64KB Flash XLP MCU | Microchip

The Microchip Technology PIC18LF26J11-I/SO is a low-power 8-bit PIC18 microcontroller from the eXtreme Low Power (XLP) family, featuring 64KB Flash program memory and 48MHz internal operation in a 28-pin SOIC wide package. Operating from 2.0V to 3.6V, the 'LF' variant is optimized for battery-backed applications and delivers up to 12 MIPS throughput at 48MHz. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (RAM), non-volatile EEPROM, and a rich set of on-chip peripherals such as timers, ADC, communication interfaces, and I/O. The PIC18LF26J11 sits within the PIC18 RISC family and belongs to the power-management-IC-adjacent hierarchy of embedded controllers; PIC18 -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor IC. Its XLP designation targets ultra-low standby current (<100 nA typical) for energy harvesting, IoT, and portable consumer products. Key features include 64KB (32K x 16) self-programmable Flash with 10K Erase/Write cycles, 4KB SRAM, an internal 31 kHz to 8 MHz oscillator with PLL (x4) reaching 48 MHz, 10-bit ADC with up to 10 channels, two analog comparators, two USART/SPI/I2C modules (ECCP/CCP/SSP), and a 16-bit Enhanced Capture/Compare/PWM peripheral. The 28-SOIC (0.295" / 7.50 mm) package is industrial-grade rated -40C to +85C and offers an easy migration path to other PIC18LF26/25/24J11 variants. Architecturally the device uses a modified Harvard 8-bit RISC core with single-cycle 16-bit instruction fetch and 8-bit data path, which simplifies code density and deterministic timing. nanoWatt XLP technology adds deep sleep, sleep with RTCC, and idle modes to extend battery life. The integrated 31kHz-8MHz HF internal RC oscillator eliminates the need for an external crystal in many designs, reducing BOM cost. Typical applications include portable medical devices (glucose meters, pulse oximeters), low-power wireless sensor nodes, smart thermostats, USB HID peripherals, consumer appliances, and battery-powered IoT edge nodes. The combination of 12 MIPS throughput, XLP standby current, and a familiar PIC18 toolchain makes the part attractive for designers migrating from older 8-bit architectures. When designing with the PIC18LF26J11-I/SO, ensure the supply voltage never exceeds 3.6V (the LF version is not 5V tolerant like PIC18F26J11) and select the appropriate configuration bits for the internal oscillator vs. external crystal. The 28-SOIC wide footprint simplifies hand-prototyping and reflow soldering; for hand-assembly or breadboard work, consider the PIC18LF26J11-I/SP (SPDIP-28) variant. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC18LF26J11-I/SS - 8-bit 48MHz 64KB Flash XLP MCU | Microchip
PIC18LF26J11-I/SS

PIC18LF26J11-I/SS - 8-bit 48MHz 64KB Flash XLP MCU | Microchip

The Microchip PIC18LF26J11-I/SS is a low-power 8-bit PIC18 microcontroller from the PIC18 J-series family, featuring 64KB of Flash program memory, 4KB RAM, and a 48 MHz internal oscillator core delivering up to 12 MIPS instruction throughput, housed in an industrial-grade 28-pin SSOP package. Operating from a 2.0V to 3.6V supply (the LF family is the low-voltage variant), it integrates a 10-bit ADC, multiple PWM/Capture/Compare peripherals, and Microchip's nanoWatt XLP (eXtreme Low Power) technology for battery-driven applications. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path. Within the broader semiconductor hierarchy, an MCU sits below microprocessors (MPUs) in compute complexity but adds on-chip Flash, RAM, and peripherals; within Microchip's portfolio it belongs to the PIC family, then to the 8-bit PIC18 sub-family, then to the J-series (high-performance, low-voltage), then to the LF (low-voltage) nanoWatt XLP subgroup. The 'J' in PIC18LF26J11 denotes the J-series, and the LF prefix specifically targets 2.0V-3.3V applications. Key features include 64KB (32K x 16) self-programmable Flash with Flash EEPROM emulation, 4KB RAM, 256 bytes of EEPROM, 10-bit ADC with up to 10 channels, 2 analog comparators, 2 MSSP (SPI/I2C) ports, 2 Enhanced USART modules, and deep-sleep current consumption in the nanoampere range. The 28-pin SSOP package provides 22 general-purpose I/O pins with Peripheral Pin Select (PPS), allowing digital peripheral functions to be remapped to any I/O. The PIC18LF26J11 uses a 16-bit modified Harvard architecture with an 8-bit data path. Its core executes most instructions in a single cycle (4 FOSC clocks) and supports priority levels for interrupts. PPS and Deep Sleep mode with Ultra Low Power Wake-up make this device highly flexible for energy-harvesting and battery-backed designs. Typical applications include low-power sensor nodes, IoT edge devices, battery-powered instrumentation, consumer electronics such as remote controls and toys, industrial control sub-modules, and any 3.3V system that needs deterministic 8-bit control with rich digital connectivity. When designing with this part, pay attention to the 3.3V supply ceiling (the LF prefix indicates the low-voltage family - the F variant without L runs to 5.5V), and use Microchip's MPLAB X development toolchain with the XC8 compiler. The 28-SSOP footprint is also shared with several other PIC18 J-series devices, easing PCB migration across memory tiers. This page synthesizes distributor pricing, drop-in pin-compatible alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC18LF26J11T-I/ML - 8-Bit XLP MCU 64KB Flash 28-VQFN | Microchip
PIC18LF26J11T-I/ML

PIC18LF26J11T-I/ML - 8-Bit XLP MCU 64KB Flash 28-VQFN | Microchip

The Microchip PIC18LF26J11T-I/ML is an 8-bit PIC® XLP™ eXtreme Low Power microcontroller with 64KB Flash, 4KB RAM, and 48MHz operation, housed in a 28-pin VQFN package with exposed thermal pad. Designed for ultra-low-power embedded applications, the device operates from 2.0V to 3.6V and supports industrial temperature ranges. This Tape-and-Reel variant is pin-compatible with the tray-packaged PIC18LF26J11-I/ML sibling, sharing identical silicon and peripheral set. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and configurable peripherals on one die. Within the broader semiconductor hierarchy, the PIC18LF26J11 belongs to the 8-bit microcontroller category, which sits between 4-bit legacy controllers and 32-bit Cortex-M0+/M4 devices. The 18J sub-family adds nanoWatt XLP technology that drops standby current to roughly 20nA, enabling battery-powered designs that previously required external RTC chips. Key differentiating features include 64KB on-chip Flash organized as 32K×16, 12 MIPS throughput from the 48MHz internal oscillator, a 10-bit ADC with up to 13 channels, two analog comparators, two USART modules, two SPI/I2C peripherals, and a 16-bit timer/counter bank. The integrated nanoWatt XLP power management block supports multiple idle and sleep modes down to 20nA, while the internal voltage regulator eliminates the need for an external 3.3V LDO in most designs. Architecturally, the PIC18LF26J11 uses a RISC Harvard-style core with single-cycle instruction execution at 48MHz (12 MIPS), 8×8 hardware multiply, and 16-bit-wide Flash bus for fast fetch. The 28-pin VQFN package exposes 34 I/O ports multiplexed across digital and analog peripherals, with a dedicated ICSP/ICD interface for in-circuit programming and debugging. The exposed thermal pad improves theta_JA for higher-current GPIO scenarios. Typical applications include portable medical sensors, IoT edge nodes, battery-powered wireless sensor nodes, USB human-interface devices, home automation controllers, and low-power industrial HMI panels. The XLP feature set is especially suited to coin-cell applications where multi-year battery life is required. When designing with this part, prefer the smallest possible active duty cycle and route the exposed pad to a continuous ground pour to maximize heat dissipation. Always validate that your compiler version supports the 18J silicon; older MPLAB 8.x builds may require recompilation for the 26J11 silicon revision. This page consolidates manufacturer specifications, distributor pricing, drop-in alternatives, and practical design notes beyond the datasheet summary for engineering evaluation.

Cotización Contacto
PIC18LF26J11T-I/SO - 64KB Flash 8-bit MCU, nanoWatt XLP | Microchip
PIC18LF26J11T-I/SO

PIC18LF26J11T-I/SO - 64KB Flash 8-bit MCU, nanoWatt XLP | Microchip

The Microchip PIC18LF26J11T-I/SO is an 8-bit PIC18J-series microcontroller with 64KB Flash, 4KB RAM, and nanoWatt XLP technology, housed in a 28-pin SOIC wide (0.295 in, 7.50 mm width) package. It executes instructions at up to 12 MIPS (48 MHz internal clock from the PLL) and operates from 4.2 V to 5.5 V, providing drop-in compatibility for 5 V PIC18 LF applications. The part delivers enhanced flash, 34 I/O pins, a 10-bit ADC with conversion capabilities, and an on-board RTCC for time-keeping with a separate 32 kHz crystal. An 8-bit PIC microcontroller belongs to the broader family of RISC microcontrollers (Reduced Instruction Set Computer) - integrated circuits that fetch, decode, and execute simplified instruction sets in typically one clock cycle. The PIC18F/LF sub-family adds a 16-bit instruction word on a modified Harvard architecture, where program and data buses are separate, allowing simultaneous instruction fetch plus data access. Within this hierarchy, PIC18LF26J11 sits at the boundary between full-performance (PIC18F) and low-power (PIC18LF) variants, and the J-suffix indicates the use of nanoWatt XLP technology and a segmented flash architecture originally derived from the PIC18F46J11. Key features include 64KB (32K x 16) of flash program memory, 4 KB SRAM data memory, 34 digital I/O pins shared with peripherals, a 10-bit analog-to-digital converter, multiple serial interfaces (I2C, SPI, USART with LIN support), and two analog comparators. The RTCC block supports time-of-day with an external 32 kHz crystal, useful for time-stamped data logging on battery-powered systems. NanoWatt XLP extreme-low-power technology delivers sleep currents in the microampere range, allowing several years of operation from coin cells. The voltage regulator of the LF J-series is internal, supporting the 2.0 V to 5.5 V (F: 2.0 V to 3.6 V, LF: 4.2 V to 5.5 V) operating ranges documented for the family. Designers should consult the data sheet for voltage-mode selection when migrating between F and LF variants. Typical applications include portable medical instruments, environmental sensor nodes with time-stamped data logging, HVAC controls, USB device controllers (with PIC18 USB variants), industrial control loops, and automotive body modules. The wide SOIC-28 footprint eases hand-soldering for prototype and rework, while the industrial temperature range (-40 C to +85 C) supports most non-automotive deployments. When designing with this device, ensure the supply voltage stays within 4.2 V to 5.5 V. Decouple VDD with 100 nF plus 10 uF bulk capacitors placed close to the pins, and consider adding a ferrite bead for noise-sensitive ADC channels. Use the ICD 3 or PICKit 3 for in-circuit programming via the ICSP interface. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC18LF26J13-I/ML - 64KB Flash, 48MHz 8-bit MCU | Microchip
PIC18LF26J13-I/ML

PIC18LF26J13-I/ML - 64KB Flash, 48MHz 8-bit MCU | Microchip

The Microchip Technology PIC18LF26J13-I/ML is an 8-bit PIC18 XLP nanoWatt microcontroller with 64KB Flash, 4KB RAM, and a 12-bit ADC, housed in a 28-pin QFN (ML) 6x6 mm package with exposed pad. It operates at up to 48 MHz (12 MIPS) from a 2.0-3.6 V supply and is positioned for low-power, cost-sensitive embedded designs in the PIC18 J-series family. An 8-bit microcontroller (MCU) is a self-contained computing element integrating a CPU core, program memory, RAM, peripherals, and I/O on a single die. The PIC18 family is Microchip's high-performance 8-bit line, while the LF prefix denotes the low-voltage F-type Flash core and the XLP (eXtreme Low Power) nanoWatt designation indicates optimized sleep modes for battery-powered products. Within the broader taxonomy, the PIC18LF26J13 sits under: microcontroller -> 8-bit MCU -> PIC18 family -> PIC18 J-series -> low-power sub-family. Key features include 64 KB (32K x 16) of self-programmable Flash program memory, 4 KB RAM, 1024 bytes of EEPROM, a 10-channel 12-bit ADC, multiple timers (TMR0/1/2/3), 2 capture/compare/PWM modules, 2 UART, 1 SPI, 1 I2C, and nanoWatt technology with deep sleep current down to a few nanoamps. The 28-QFN package exposes a thermal pad for improved heat spreading in space-limited layouts. Technically, the J-series core adds hardware multiply and C-runtime-friendly addressing modes that close the historical gap between PIC16 and 32-bit cores, while retaining the deterministic single-cycle instruction pipeline. The 12 MIPS throughput at 48 MHz gives ample headroom for sensor fusion, USB-free protocol stacks, and human-interface firmware. Typical applications include low-power IoT sensor nodes, battery-powered medical monitors, consumer appliances, USB HID class replacements, and industrial control panels. Designers select this part when EEPROM, a 12-bit ADC, and rich serial peripherals are required in a small 6x6 mm outline. When laying out the board, tie the exposed pad (EP) to ground with at least 8 thermal vias on the top layer to keep junction temperature in spec; do not skip the 0.1 uF decoupling pair on VDD/AVDD plus a 10 uF bulk capacitor. Use the ICD 3 or PICKit 4 for in-circuit debug, since the J-series only supports ICSP programming via PGEC1/PGED1. This page synthesizes distributor pricing, drop-in same-family alternatives, and design notes that go beyond what the manufacturer datasheet alone provides.

Cotización Contacto
PIC18LF26J13-I/SO - 8-bit 48MHz 64KB Flash MCU | Microchip
PIC18LF26J13-I/SO

PIC18LF26J13-I/SO - 8-bit 48MHz 64KB Flash MCU | Microchip

The Microchip PIC18LF26J13-I/SO is an 8-bit PIC18 XLP nanoWatt microcontroller with 64KB (32K x 16) Flash program memory, 4KB RAM, and a 48MHz internal oscillator, packaged in a 28-pin SOIC (0.295" / 7.50mm width). The 'LF' prefix denotes the low-voltage variant supporting 2.0V to 3.6V core operation, while the 'J13' family integrates nanoWatt XLP power management, a 12-bit ADC, multiple PWM/SCCP modules, and USB-/Ethernet-ready peripherals for connected embedded designs. A PIC18 microcontroller is a member of Microchip's 8-bit PIC (Peripheral Interface Controller) family built on a Harvard RISC architecture with a modified instruction set optimized for deterministic single-cycle execution (except branches). PIC18F/LF parts sit between the baseline PIC10/12/16 line and the 16-bit dsPIC/PIC24 family, offering a richer peripheral set (12-bit ADC, CCP/SCCP, MSSP, EUSART) and larger memory while remaining programmable in nanolit. Within the PIC18 hierarchy, the LF sub-line is the low-Vdd branch designed for battery-powered XLP (eXtreme Low Power) applications, with sleep currents measured in nanoamps. Key features of the PIC18LF26J13 include 64KB Flash self-programmable via ICSP, 4KB SRAM, up to 28 I/O, 12-bit A/D converter with up to 10 channels, multiple Enhanced CCP (ECCP) and Capture/Compare/PWM (CCP) modules, two MSSP (SPI/I2C) ports, two EUSART modules with LIN support, real-time clock (RTCC) with calendar, and nanoWatt XLP technology offering <100 nA typical sleep current with RTCC and WDT active. The integrated 48MHz precision internal oscillator removes the external crystal in many cost-sensitive designs. The PIC18LF26J13 uses an enhanced Harvard core with 16-bit instructions and a hardware multiplier, executing most instructions in one cycle (~83 ns at 48 MHz FOSC). On-chip peripherals are mapped via a Peripheral Pin Select (PPS) module, allowing flexible pin remapping of digital functions. The 12-bit ADC supports up to 16 channels with automated channel scanning, while the CTMU module provides touch sensing and capacitive proximity measurement. Typical applications include battery-powered sensor nodes, USB peripherals, home appliances with LCD/keypad interfaces, industrial control panels, and low-power wireless sensor networks paired with sub-GHz transceivers. The combination of nanoWatt sleep modes and 12-bit ADC makes the part suitable for energy-harvesting and remote-monitoring designs. When designing with this device, ensure VDD decoupling is placed close to the pins and that the internal 48 MHz configured for precision (INTOSC) accuracy is acceptable for timing-critical peripherals such as EUSART. Pin-compatible PIC18F26J13 variants operate over a wider 2.0V-3.6V/4.2V-5.5V range but consume more active current. This page synthesizes distributor pricing for SOIC-28 variants, drop-in alternatives within the PIC18LF26J13 family, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC18LF26J13-I/SP - 8-bit 48MHz 64KB Flash MCU | Microchip
PIC18LF26J13-I/SP

PIC18LF26J13-I/SP - 8-bit 48MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18LF26J13-I/SP is an 8-bit PIC18J-series microcontroller featuring a 48 MHz internal clock, 64 KB of Flash program memory, 4 KB of RAM, and an integrated 12-bit ADC, housed in a 28-pin SPDIP (SP) through-hole package. According to the Verified Web Data summary, this member of the PIC XLP 18J family targets low-power and high-performance 8-bit embedded designs that need generous program space and a rich peripheral set. What is an 8-bit microcontroller? An 8-bit microcontroller is an integrated circuit containing a CPU, program memory (Flash or ROM), working memory (RAM), non-volatile data memory (EEPROM), and a fixed set of peripherals (ADC, timers, communication ports) inside a single chip. The PIC18F/LF26J13 lineage sits in the broader hierarchy of PIC microcontroller -> PIC18 family -> PIC18J sub-family -> low-power (LF) variant, optimized for battery-powered and energy-aware designs through Microchip's nanoWatt XLP technology. Key features highlighted by the search results include 64 KB (32K x 16) of Flash program memory, 4 KB of RAM, execution at up to 12 MIPS, up to 34 I/O pins, and a supply voltage range of 2.0 V to 3.6 V for the LF variant, supporting industrial operating temperatures. Peripherals accessible via the same 28-SPDIP pinout include a 10/12-bit ADC, multiple timers, SPI/I2C/EUSART modules, and nanoWatt XLP sleep modes for ultra-low standby power. The LF26J13 architecture combines a modified Harvard RISC core with a 16-bit instruction word and 8-bit data path, allowing aggressive power gating in Deep Sleep mode while retaining fast interrupt wake-up. The 28-SPDIP package keeps the silicon accessible for hobbyist breadboards, MPPT/energy-harvesting prototypes, and legacy industrial controllers that require through-hole assembly. Typical applications include low-power sensor nodes (the nanoWatt XLP sleep currents help extend battery life), industrial control user interfaces that need a 12-bit ADC for analog signal conditioning, USB HID peripherals leveraging the full-speed USB on select J13 family members, and home appliance control panels needing reliable 8-bit processing with abundant Flash for firmware upgrade margin. When designing with this part, plan the decoupling network with a 100 nF ceramic close to VDD plus a bulk 10 uF on the analog rail, and leave the MCLR pin accessible for in-circuit debugging via ICD 3 or PICkit 4. Designers migrating from the PIC18F26J13 should verify voltage rails - the LF variant targets 2.0-3.3 V systems, while the F variant supports 2.0-3.6 V with 5 V-tolerant I/O. This page combines distributor pricing benchmarks, pin-compatible drop-in alternatives from the PIC18F/LF26J13 family, and field-validated design notes that are not duplicated in the manufacturer datasheet.

Cotización Contacto
PIC18LF26J13-I/SS - 64KB Flash 8-bit MCU 48MHz SSOP-28 | Microchip
PIC18LF26J13-I/SS

PIC18LF26J13-I/SS - 64KB Flash 8-bit MCU 48MHz SSOP-28 | Microchip

The Microchip Technology PIC18LF26J13-I/SS is an 8-bit RISC microcontroller from the PIC18 J-series featuring 64KB Flash program memory (32K x 16 organization) and 4KB RAM, executing at up to 48 MHz (12 MIPS) in a 28-pin SSOP package. It belongs to Microchip's PIC XLP eXtreme Low Power family, providing deeply integrated peripherals and ultra-low-power modes for battery-constrained applications while sustaining sustained computational throughput across industrial temperature grades. A PIC microcontroller is a Harvard-architecture 8-bit MCU built around a RISC instruction set, on-chip Flash program memory, RAM, EEPROM and rich peripherals including ADC, timers and serial communication blocks. Within the broader taxonomy the part sits at: microcontroller -> 8-bit MCU -> PIC18 family -> PIC18 J-series -> nanoWatt XLP variants. The LF prefix denotes the LF (Low-Voltage/Frequency) variant scaled for 2.0-2.75V wide-range supply rails typical of single-cell Li-ion or 2-AA battery systems, whereas the F variant (PIC18F26J13) shares the same silicon die but supports the wider 2.15-3.6V range. Key features include 64KB self-programmable Flash with 4KB SRAM, 10-bit and 12-bit ADC channels, dual USART, dual SPI and I2C interfaces, and 22 general-purpose digital I/O pins. nanoWatt XLP technology adds deep sleep, doze and idle modes that drop quiescent current into the sub-microamp range, enabling multi-year coin-cell lifetimes in sleep-dominant applications. The architecture combines a 16-bit instruction word with an 8-bit data path, plus a peripheral-rich core that integrates comparators, capture/compare/PWM modules, a real-time clock and a CTMU charge-time measurement unit for capacitive touch sensing. Hardware multiplier and hardware DMA-style peripheral arbitration minimise CPU overhead in mixed-signal designs. Typical applications include battery-powered sensor nodes, portable medical devices, industrial control and HMI panels, USB-to-UART bridges, capacitive touch human-machine interfaces, and home automation controllers. The dual-USART plus dual-SPI combination makes it especially attractive for multi-bus sensor aggregation. Designers targeting multi-rail power domains or systems requiring sequenced shutdown benefit from the LF-variant low-voltage threshold. When using this part, ensure VDD decoupling uses a 100 nF ceramic plus 1 uF bulk within 5 mm of the pins, and configure the CONFIG register for the correct oscillator mode (HS, XT or INTOSC) before code lock. For capacitive touch applications allocate a 10 ms scan budget and route the CTMU pins with guarded ground to suppress noise injection. This page synthesizes distributor pricing, parametric comparison tables, pin-compatible drop-in alternatives and practical design notes that extend the manufacturer datasheet context.

Cotización Contacto
PIC18LF26J13T-I/ML - 64KB Flash XLP 8-bit MCU 28-VQFN | Microchip
PIC18LF26J13T-I/ML

PIC18LF26J13T-I/ML - 64KB Flash XLP 8-bit MCU 28-VQFN | Microchip

The Microchip Technology PIC18LF26J13T-I/ML is a low-power 8-bit PIC microcontroller from the PIC18 XLP family, offering 64KB of Flash program memory (32K x 16) and 3.8KB of RAM, operating at up to 48MHz (12 MIPS) in a 28-pin VQFN (ML, 6x6 mm) package with exposed thermal pad. The device belongs to the PIC18 J-series, integrates an internal oscillator, and supports 22 digital I/O lines plus a 12-bit ADC, making it suitable for general-purpose embedded designs that demand low active and sleep currents. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile working RAM, and a rich set of peripherals (ADC, timers, communication interfaces, GPIO). The PIC18 family uses a modified Harvard RISC architecture with 16-bit instructions and 8-bit data, optimized for deterministic real-time response. Within the broader hierarchy, an 8-bit MCU sits below 32-bit Cortex-M devices in raw compute power but typically wins on cost, simplicity, and active-current efficiency in cost-sensitive or battery-powered designs. Key features of the PIC18LF26J13T-I/ML include 64KB Flash, 3.8KB RAM, 22 I/O pins, internal oscillator, 12-bit A/D converter, and Microchip's eXtreme Low Power (XLP) technology, which enables nanoWatt sleep modes for long battery life. The wide 2.0V-3.6V operating range simplifies direct connection to single-cell Li-ion or two-AA battery stacks without additional regulation. The 28-VQFN (ML) 6x6 mm package with exposed pad supports efficient thermal dissipation and compact PCB layouts. The PIC18 J-series core runs instructions in 4 clock cycles, achieving 12 MIPS at 48 MHz, with hardware multiplier, C compiler friendly architecture, and rich peripheral set including USB, SPI, I2C, and UART. The integrated 12-bit ADC delivers up to 16 channels for sensor acquisition, and the nanoWatt XLP power management provides multiple software-selectable sleep modes with wake-on-interrupt capability for energy harvesting applications. Typical applications include battery-powered sensor nodes, USB peripherals, industrial control panels, consumer appliances, and low-cost IoT edge devices where the combination of XLP nanoWatt sleep, USB, and ample Flash is decisive. When designing with this part, ensure proper decoupling (100 nF plus 10 uF bulk) close to the VDD pins, follow the recommended PCB layout for the exposed thermal pad, and consult Microchip's PIC18 J-series family reference manual for peripheral configuration.

Cotización Contacto
PIC18LF26J13T-I/SS - 8-bit 48MHz XLP MCU 64KB Flash | Microchip
PIC18LF26J13T-I/SS

PIC18LF26J13T-I/SS - 8-bit 48MHz XLP MCU 64KB Flash | Microchip

The Microchip Technology PIC18LF26J13T-I/SS is an 8-bit PIC18 XLP microcontroller with 64KB Flash, 3.8KB RAM, 12 MIPS performance, and a 12-bit ADC, housed in a 28-pin SSOP package on tape-and-reel. It is designed for low-power, high-performance embedded applications requiring a balance of code density, peripheral integration, and ultra-low power consumption. An 8-bit PIC microcontroller (MCU) is a single-chip computer built on a Harvard architecture with separate program and data buses, optimized for deterministic real-time control. Within the broader microcontroller hierarchy, the PIC18 family sits above PIC16 and PIC10/12 devices, below the PIC24/dsPIC line, and ultimately belongs to the embedded microcontroller > RISC processor > semiconductor taxonomy. The "LF" prefix denotes the wide-voltage 1.8V-3.6V variant optimized for battery-powered systems, while "J13" identifies the specific family combining enhanced peripherals with XLP nanoWatt technology. Key features include 64KB Flash program memory (32K x 16 words), 3.8KB RAM, 22 digital I/O pins, internal oscillator support, and 12 channels of 10/12-bit ADC. The 12 MIPS execution rate (at 48 MHz) provides responsive control loops, while deep sleep current in the nanoWatt range allows years of operation from a single coin cell. Multiple serial interfaces including I2C, SPI, and enhanced USART enable flexible peripheral connectivity for sensor and communication subsystems. The device combines a RISC instruction set with C-optimized architecture and a wide array of core-independent peripherals such as CCP, enhanced PWM, and configurable logic cells. This peripheral integration reduces external component count and BOM cost while offloading tasks from the CPU. Internal voltage reference and self-programming Flash further simplify system design. Typical applications include portable medical devices, IoT sensor nodes, battery-powered instrumentation, home automation controllers, and consumer electronics with USB or display interfaces. The XLP technology makes it especially attractive for energy-harvesting and remote-sensing designs where quiescent current dominates battery life. When designing with this MCU, careful decoupling near VDD pins and adherence to the trace-length guidelines in the datasheet are essential for ADC accuracy. Internal oscillator trimming may be required for time-critical protocols such as USB or CAN. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and selecting the PIC18LF26J13T-I/SS.

Cotización Contacto