Microcontroladores

Productos (18747)

PIC24FJ16MC102T-I/ML - 16-bit 16 MIPS 16KB Flash Motor MCU | Microchip
PIC24FJ16MC102T-I/ML

PIC24FJ16MC102T-I/ML - 16-bit 16 MIPS 16KB Flash Motor MCU | Microchip

The Microchip Technology PIC24FJ16MC102T-I/ML is a 16-bit RISC PIC24F motor-control microcontroller with 16 KB Flash, 1 KB RAM, and a 16 MIPS CPU core, housed in a 28-pin QFN (6x6 mm) package with exposed thermal pad. It is part of the PIC24FJ16MC101/102 family optimized for low-cost, low-pin-count motor control with integrated peripherals for single-chip BLDC, PMSM, and stepper drive stages. The 'T' suffix denotes tape-and-reel packaging, and the 'I' suffix denotes the -40C to +85C industrial operating temperature range. A 16-bit microcontroller (MCU) is an integrated computing device that combines a CPU core, program memory (Flash), data memory (RAM), and a rich peripheral set on a single silicon die. The PIC24F core uses a modified Harvard RISC architecture with a 16-bit instruction word, executing up to 16 million instructions per second (16 MIPS) at 32 MHz CPU clock. Within the broader semiconductor hierarchy, the PIC24FJ16MC102T sits in the microcontrollers category, a sub-class of microcontrollers (MCU) > embedded controllers > integrated circuits > semiconductors, and is positioned specifically in motor-control-optimized sub-family. Key features of this part include six enhanced 16-bit PWM outputs with edge-aligned or center-aligned modes and up to 7.5 ns PWM resolution, four 16-bit timers, two I2C, two SPI, two UART, 13 ADC channels at 500 ksps with 10-bit resolution, a Charge Time Measurement Unit (CTMU) for capacitive touch and time-of-flight measurement, and Peripheral Pin Select (PPS) for flexible pin-function remapping. The 28-QFN (6x6) package has a low thermal resistance and supports industrial-grade -40C to +85C operation. From an architecture perspective, the PIC24FJ16MC102T-I/ML combines an aggressive 16-bit RISC engine with motor-tuned analog and timing peripherals. The CTMU enables precise current sensing and capacitive touch, while PPS allows designers to remap digital peripheral I/O to multiple physical pins, simplifying PCB routing. The 16 MIPS throughput at 32 MHz (4:1 instruction-cycle multiplier of the 8 MHz internal oscillator with PLL) provides deterministic control-loop execution for FOC or trapezoidal motor commutation. Typical applications include 3-phase BLDC or PMSM motor drives (low-voltage, sub-100 W), brushed DC motor controllers, electronic speed controllers (ESCs) for small drones and RC vehicles, fan and pump controllers, LED lighting controllers with analog dimming, and small-appliance motor control. The integrated 6-output PWM, 13 ADC inputs, and QEI (Quadrature Encoder Interface) support sensorless or sensor-based field-oriented control without external logic ICs. When designing with this device, allocate a 10 uF bulk decoupling capacitor plus 0.1 uF high-frequency bypass near the VDD pins, route the analog AVDD separately from VDD for ADC noise immunity, and follow Microchip AN1078 or AN1160 for sensorless FOC firmware reference. The exposed thermal pad of the QFN package should be soldered to a sufficient copper pour to keep junction temperature within the 85C industrial limit. This page synthesizes distributor pricing, drop-in alternatives from the same product family, and practical design notes that are not collected in the manufacturer datasheet alone, giving an engineer a single-point reference for selection and procurement.

Cotización Contacto
PIC24FJ16MC102T-I/SO - 16-bit 16 MIPS Motor Control MCU | Microchip
PIC24FJ16MC102T-I/SO

PIC24FJ16MC102T-I/SO - 16-bit 16 MIPS Motor Control MCU | Microchip

The Microchip PIC24FJ16MC102T-I/SO is a 16-bit PIC microcontroller from the PIC24F motor-control series, delivering 16 MIPS at 32 MHz while integrating dedicated motor-control peripherals. Housed in a 28-pin SOIC package (7.50 mm body width, surface mount), the part features 16 KB of self-programmable Flash program memory (5.5K x 24 organization) and 1 KB of SRAM, supplied across the 3.0V–3.6V operating range characteristic of the PIC24FJ MC family. An MCU (microcontroller unit) is an integrated system-on-chip that combines a CPU core, volatile and non-volatile memory, and a configurable peripheral set behind a single package. The PIC24FJ family implements a modified Harvard architecture with a 16-bit data path, a 24-bit instruction word, and a 17-bit by 16-bit hardware multiplier; code is executed in a single cycle from Flash, and the device is C-compiler-optimized for embedded application development. The motor-control (MC) sub-family extends this base with peripherals specifically engineered for driving BLDC, PMSM, ACIM and stepper stages. Key features of the PIC24FJ16MC102T-I/SO include up to 6 PWM channels with dedicated PWM time bases for complementary, edge-aligned or center-aligned switching, a 6-channel 10-bit ADC with conversion rates up to 500 ksps, multiple communication interfaces (UART, SPI, I2C), an 8 MHz internal oscillator with 4x PLL option (yielding 32 MHz operation), and CTMU support for touch and current sensing. The device supports industrial-grade -40 °C to +85 °C operation, three 16-bit timers and one 32-bit timer, and PPS (Peripheral Pin Select) for flexible I/O mapping. Architecturally, the PIC24FJ MC family combines the standard PIC24 core with a Motor Control PWM (MCPWM) module capable of generating complementary PWM outputs with programmable dead time, a high-speed ADC trigger, and a QEI (Quadrature Encoder Interface) for closed-loop rotor position sensing. The CTMU (Charge Time Measurement Unit) provides on-chip timing for capacitive touch and for current-sensing analog front-ends, removing external analog conditioning. Typical applications include low-cost BLDC and PMSM sensorless or sensored motor drives (small fans, pumps, appliance motors), 3D-printer stepper control, washing-machine and home-appliance motor boards, and LED lighting power stages. Its small 28-SOIC footprint is also attractive for hobby motor-control boards and Christmas-light controllers where board area is constrained. When designing with this part, ensure the supply is decoupled with 10 µF bulk plus 100 nF ceramic close to VDD/AVDD pins, and respect the 3.6 V absolute maximum to avoid latch-up. The 'T' suffix indicates Tape & Reel packaging, and the -I (Industrial) temperature grade covers -40 °C to +85 °C operation. This page synthesizes distributor pricing, drop-in alternatives in the same SOIC-28 footprint, and practical design notes not aggregated in any single distributor listing — useful for engineers evaluating second-source or pin-compatible replacements for the PIC24FJ16MC102T-I/SO.

Cotización Contacto
PIC24FJ16MC102T-I/SS - 16-bit 16 MIPS 16KB Flash Motor Control MCU | Microchip
PIC24FJ16MC102T-I/SS

PIC24FJ16MC102T-I/SS - 16-bit 16 MIPS 16KB Flash Motor Control MCU | Microchip

The Microchip PIC24FJ16MC102T-I/SS is a 16-bit ultra-low-cost motor-control microcontroller built on the PIC24F architecture, delivering 16 MIPS performance from a 32 MHz maximum core clock and integrating 16 KB of Flash program memory with 1 KB of SRAM. It is housed in a 28-pin Shrink Small Outline Package (SSOP-28) and is specified over the -40 °C to +85 °C industrial temperature range. The 'T' suffix indicates Tape & Reel packaging and the 'I' suffix denotes the industrial temperature grade. What is a motor-control MCU? A motor-control microcontroller is a class of embedded processor optimized for driving brushed DC, brushless DC (BLDC), stepper, and switched reluctance motors. These MCUs integrate dedicated peripherals such as multi-channel PWM modules, high-resolution timers, fast ADCs for current sensing, and input-capture blocks for rotor position feedback. Motor-control MCUs sit inside the broader hierarchy: microcontroller -> embedded processor -> semiconductor IC, and within Microchip's portfolio they form the PIC24F MC family, with the dsPIC33 family providing higher-performance DSP-extended variants. Key features include a 6-channel 10-bit ADC for analog feedback, three 16-bit and one 32-bit timer/counter, a Charge Time Measurement Unit (CTMU) for capacitive touch or temperature sensing, Peripheral Pin Select (PPS) for flexible I/O mapping, and up to 21 general-purpose I/O pins. The integrated Motor Control PWM (MCPWM) module supports complementary outputs with programmable dead time, hardware fault input, and center-aligned or edge-aligned modes - all essential for safe half-bridge and full-bridge drive stages. Typical applications include low-cost BLDC ceiling fans, small appliance pump controllers, drone ESCs, HVAC damper drivers, and low-voltage sensorless FOC platforms where the MCU must execute a real-time control loop in software. The 16 MIPS headroom and CTMU simplify sensor integration in space-constrained designs. Designers should budget Flash for a bootloader or field firmware updates, since 16 KB fills quickly when adding a full motor-control state machine.

Cotización Contacto
PIC24FJ192GA106-E/PT - 192KB Flash 16-bit MCU 64-TQFP
PIC24FJ192GA106-E/PT

PIC24FJ192GA106-E/PT - 192KB Flash 16-bit MCU 64-TQFP

The Microchip Technology PIC24FJ192GA106-E/PT is a 16-bit general-purpose Flash microcontroller from the PIC24FJ family, featuring 192KB of on-chip Flash program memory, 16KB of RAM, and a 64-pin TQFP (10x10 mm) package. The device operates at up to 32 MHz CPU clock with a 16-bit modified Harvard architecture and includes peripheral pin select (PPS) for flexible I/O mapping. This PIC microcontroller belongs to the PIC24FJ family of low-power 16-bit MCUs, a category that bridges the gap between 8-bit PIC16/PIC18 devices and 32-bit PIC32 parts. The PIC24FJ series integrates a wide peripheral set (UART, SPI, I2C, ADC, timers, RTCC, CTMU) on a single die and is intended for low-power (<100 nA standby current), connectivity-rich embedded applications that benefit from multiple serial ports and large memory footprints. Key features include three I2C, three SPI, four UART serial interfaces, 23 independent timers, a 16-channel 10-bit ADC, three analog comparators with programmable I/O, a hardware real-time clock/calendar (RTCC), and a charge time measurement unit (CTMU) for capacitive touch sensing. The integrated Peripheral Pin Select (PPS) remapping allows most digital peripherals to be assigned to a wide range of I/O pins, easing PCB layout. Typical applications include industrial control panels, low-power remote sensor nodes, USB/audio bridging bridges, graphic TFT display controllers, and capacitive-touch human-machine interfaces. The wide peripheral mix also suits medical instrumentation and connected consumer appliances. When designing with this MCU, observe the core decoupling rule: a low-ESR capacitor (such as tantalum) must be placed at the VDDCORE pin to stabilize the on-chip regulator. Programming/debugging is supported by Microchip's MPLAB ICD tools and the in-circuit debugger via dedicated PGx pins. This page synthesizes distributor pricing, drop-in PIC24FJ family alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC24FJ192GA106-I/PT - 16-bit 32MHz 192KB Flash MCU | Microchip
PIC24FJ192GA106-I/PT

PIC24FJ192GA106-I/PT - 16-bit 32MHz 192KB Flash MCU | Microchip

The Microchip Technology PIC24FJ192GA106-I/PT is a 16-bit general-purpose Flash microcontroller in the PIC24F family, delivering 32 MIPS performance at 32 MHz, 192 KB of program Flash, 16 KB of RAM, and 53 general-purpose I/O pins, all housed in a 64-pin TQFP (10x10 mm) package. It integrates Peripheral Pin Select (PPS) for flexible signal routing, 3x I2C, 3x SPI, 4x UART, five 16-bit timers, a 16-channel 10-bit ADC, three analog comparators with programmable I/O, a hardware Real-Time Clock/Calendar (RTCC), and a Charge Time Measurement Unit (CTMU), making it a feature-dense general-purpose MCU for embedded designs. An MCU (microcontroller unit) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a range of on-chip peripherals (ADC, timers, communication controllers, I/O). The PIC24FJ192GA106 belongs to the 16-bit PIC24F family of microcontrollers from Microchip, which sits below dsPIC33/PIC32 in the company's MCU hierarchy and is optimized for low-power general-purpose applications. It operates across the broader Microchip MCU taxonomy that includes 8-bit PIC10/12/16/18 families, 16-bit PIC24F/dsPIC33, and 32-bit PIC32 families. Key differentiating features include a Peripheral Pin Select (PPS) remappable peripheral system, 23 independent timers (5x 16-bit plus 16-bit Pair for input capture and PWM), on-chip USB 2.0 full-speed support, and ultra-low standby current under 100 nA with RTCC operation, enabling battery-backed designs. The architecture uses a 16-bit Modified Harvard RISC core with a 16-element x 16-bit working register array and executes most instructions in one cycle, achieving up to 32 MIPS at 32 MHz while operating from 2.0 V to 3.6 V. Typical applications include low-power industrial sensor hubs, USB HID peripherals, HVAC control panels, multi-protocol bridge devices, handheld instrumentation, medical patient monitoring, and automotive infotainment auxiliary controllers. The combination of PPS, large RAM (16 KB) for buffering, and multiple serial ports (3x I2C, 3x SPI, 4x UART) makes it ideal for connectivity-centric applications that need to talk to many peripherals simultaneously. When designing with this device, ensure the JTAG/ICSP programming interface is correctly routed to programming headers and that PPS configuration in firmware is verified before debugging peripheral issues. The PPS system greatly simplifies PCB layout because peripheral functions can be remapped to multiple physical pins in software, but this also means initial firmware must configure PPS registers before peripherals can be used.

Cotización Contacto
PIC24FJ192GA106T-I/PT - 192KB Flash 16-bit MCU, 64-TQFP | Microchip
PIC24FJ192GA106T-I/PT

PIC24FJ192GA106T-I/PT - 192KB Flash 16-bit MCU, 64-TQFP | Microchip

The Microchip Technology PIC24FJ192GA106T-I/PT is a 16-bit PIC24F microcontroller with 192 KB of Flash program memory, 16 KB of RAM, and a 32 MHz (16 MIPS) CPU core, housed in a 64-pin TQFP (10x10 mm) package. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals into one device. The PIC24FJ family uses a 16-bit RISC Modified Harvard architecture with eXtreme Low Power (XLP) technology, sitting in the hierarchy: PIC24F -> 16-bit MCU -> microcontroller -> embedded processor -> semiconductor. This part is the tape-and-reel (T), industrial temperature (-I), 64-pin TQFP (/PT) variant. Key features include 192 KB (65.5K x 24) Flash, 16 KB RAM, 53 digital I/O pins, 3x I2C, 3x SPI, 4x UART, 23 independent timers, a 16-channel 10-bit ADC, three analog comparators, hardware RTCC, CTMU, and Peripheral Pin Select (PPS) for flexible signal routing. Standby current is below 100 nA in XLP sleep modes. The 32 MHz core delivers 16 MIPS throughput while consuming roughly 0.8 mA/MIPS active, with on-chip regulators supporting 2.0-3.6 V VDD. PPS allows most digital peripherals to be mapped to most I/O pins, simplifying PCB layout. The CTMU enables touch sensing, capacitive measurement, and time-of-flight applications. Typical applications include industrial control with connectivity (3x I2C, 3x SPI, 4x UART), low-power IoT sensor nodes using XLP sleep, HMI/touch interfaces via CTMU, and USB-free general-purpose embedded control. Multiple serial ports allow simultaneous sensor bus, display bus, and debug channels. When designing, observe VDD 2.0-3.6 V, place 0.1 uF + 10 uF decoupling near each VDD/VSS pair, and use PPS registers to assign peripheral functions. Industrial -40 C to +85 C operation is supported.

Cotización Contacto
PIC24FJ192GA108-I/PT - 192KB Flash 16-bit MCU 80-TQFP | Microchip
PIC24FJ192GA108-I/PT

PIC24FJ192GA108-I/PT - 192KB Flash 16-bit MCU 80-TQFP | Microchip

The Microchip PIC24FJ192GA108-I/PT is a 16-bit PIC24F general-purpose flash microcontroller featuring 192 KB of program flash and 16 KB of RAM, housed in an 80-pin TQFP (PT) package with 12x12 mm body size. Operating from a 2.0V to 3.6V supply and reaching up to 32 MHz MIPS performance, the device targets low-power connected applications with sub-100 nA standby current. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program memory, data RAM, and peripherals (UART, SPI, I2C, ADC, timers) into a single chip. The PIC24F family belongs to the wider taxonomy: microcontroller -> embedded processor -> semiconductor IC. PIC24F parts use Microchip's modified Harvard RISC architecture with 16-bit instructions and 24-bit instruction words, designed to balance deterministic real-time response with low energy consumption for portable and battery-backed designs. Key features of the PIC24FJ192GA108 include: 192 KB flash (65.5K x 24 words), 16 KB SRAM, 4 KB EEPROM-like data flash, 16 MIPS at 32 MHz CPU speed, and a peripheral set covering 3x I2C, 3x SPI, 4x UART, and 23 independent timers. The part supports USB, Real-Time Clock and Calendar (RTCC), 16-channel 10-bit ADC, and parallel master port, while integrated nanoWatt XLP technology keeps standby draw below 100 nA. Internally the device separates regulated core power (1.8V via internal LDO) from I/O power (2.0-3.6V), enabling mixed-voltage peripherals. The 80-pin TQFP exposes up to 69 digital I/O lines and supports 5V-tolerant inputs, while programming is handled through ICSP and JTAG. This combination of high memory density and rich connectivity makes the part suitable for applications that previously required multiple 8-bit MCUs. Typical applications include industrial sensor hubs, low-power wireless gateways, USB human-interface devices (HID), battery-backed data loggers, and consumer appliances requiring graphical LCDs via integrated PMP. The 4x UART channels are particularly useful for protocol-bridging gateways (RS-232/485 to USB) and the parallel master port can directly drive external graphics memory. When designing with this device, ensure all VSS/VDD pins are connected per datasheet, ENVREG is configured correctly for internal vs external voltage regulator mode, and the JTAG/ICSP pins are reserved for in-circuit debugging unless disabled in firmware. This page synthesizes distributor pricing, drop-in alternatives, application notes, and PCB layout guidance not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FJ192GA108T-I/PT - 192KB Flash 16-bit MCU 80-TQFP | Microchip
PIC24FJ192GA108T-I/PT

PIC24FJ192GA108T-I/PT - 192KB Flash 16-bit MCU 80-TQFP | Microchip

The Microchip Technology PIC24FJ192GA108T-I/PT is a 16-bit PIC24F RISC general-purpose flash microcontroller featuring a 32 MHz core, 192 KB of program Flash memory (65.5K x 24 words), and 16 KB of RAM, housed in an 80-pin TQFP (12x12 mm) package. It belongs to the PIC24FJ192GA108 family, which combines low-power operation (<100 nA standby current) with a rich connectivity peripheral set designed for embedded applications requiring multiple serial interfaces and large memory buffers. What is a PIC24F microcontroller? A PIC24F is a 16-bit RISC microcontroller from Microchip that sits in the hierarchy: microcontroller (MCU) -> 16-bit MCU -> flash MCU -> low-power MCU -> PIC24F family. It is the lower-power complement to the dsPIC/PIC24H line, and is engineered for battery-friendly applications where 8-bit PICs lack memory or peripheral bandwidth but the system does not need a DSP engine. The 'F' suffix denotes Flash program memory and the 'J' denotes the nanoWatt XLP-style ultra-low-power process. Key features include 192 KB self-reprogrammable flash, 16 KB SRAM, an operating voltage range of 2.0 V to 3.6 V with 5.5 V tolerant digital inputs, three I2C, three SPI, four UART, and 23 independent timers. The device supports multiple power management modes (Sleep, Idle, Doze) with fast wake-up, configurable open-drain outputs, and high-current 18 mA sink/source capability on every I/O pin. It also integrates a Parallel Master Port (PMP) for off-chip memory or graphics expansion. Architecturally, the PIC24FJ192GA108T-I/PT uses a modified Harvard architecture with a 16-bit datapath and 24-bit instruction word. The CIP (Core Independent Peripherals) approach allows hardware state machines to handle timing-sensitive tasks without CPU intervention, reducing active time and current draw. The 32 MHz core delivers 16 MIPS of throughput while operating from as low as 2.0 V. Typical applications include industrial control and HMI panels, portable medical instrumentation, low-power sensor hubs, USB and serial gateway bridges, and battery-backed telemetry devices. The 16 KB RAM buffer is particularly useful for protocol stacks and audio sample buffering in DSP-lite workloads. Designers should pay attention to the 2.0-3.6 V supply constraint and avoid 5 V system buses unless using the 5.5 V tolerant digital inputs. Decoupling requires at least one 100 nF ceramic capacitor per VDD/VSS pair plus a bulk 10 µF near the ICSP programming header. For firmware development, MPLAB X IDE with the XC16 compiler is the standard toolchain. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not consolidated on the manufacturer datasheet alone - useful for engineers evaluating long-term availability and second-source options for industrial programs.

Cotización Contacto
PIC24FJ192GA110-E/PT - 16-bit 192KB Flash MCU | Microchip
PIC24FJ192GA110-E/PT

PIC24FJ192GA110-E/PT - 16-bit 192KB Flash MCU | Microchip

The Microchip Technology PIC24FJ192GA110-E/PT is a 16-bit, general-purpose flash microcontroller in the PIC24F family, featuring 192 KB of self-reprogrammable flash, 16 KB of RAM, and a 32 MHz MIPS core capable of 16 MIPS throughput. Housed in a 100-pin TQFP (12x12 mm) surface-mount package, the -E temperature-grade suffix designates the extended industrial temperature range of -40C to +125C. A PIC24F microcontroller is a 16-bit modified-Harvard RISC MCU designed by Microchip for embedded control applications that demand low power, ample memory, and rich connectivity. Within the broader taxonomy it sits between 8-bit PIC MCUs and 32-bit PIC32 devices, balancing code density, peripheral integration, and cost. PIC24F parts share the PIC24 instruction set with 16-bit data paths and execute one instruction per two clock cycles, delivering up to 16 MIPS at 32 MHz while drawing less than 100 nA in standby. Key features include Peripheral Pin Select (PPS) for flexible I/O mapping, three I2C, three SPI, and four UART serial interfaces, twenty-three independent timers, a 16-channel 10-bit ADC with 500 ksps throughput, hardware RTCC, and selectable power management modes including Sleep, Idle, and Doze. The CTMU peripheral supports capacitive touch sensing, while Parallel Master Port and EPMP-like external bus options address larger memory or graphics subsystems. Operating voltage spans 2.0 V to 3.6 V with 5.5 V-tolerant digital inputs for mixed-voltage designs. The 100-pin TQFP package exposes up to 85 I/O pins and supports JTAG/ICSP in-system programming plus self-programmability under software control. The architectural sweet spot is battery-powered and connectivity-rich embedded applications where on-chip RAM (16 KB) doubles compared with PIC24FJ64 devices in the same pinout, enabling larger buffers, audio samples, or protocol stacks. Typical applications include industrial automation controllers, low-power sensor hubs, HMI/graphical displays, USB device-class peripherals, and consumer devices requiring UART/SPI/I2C bridging. The high RAM/flash ratio suits protocol translation, audio streaming, and lightweight graphics rendering. When designing, take advantage of PPS to remap peripherals to available pins and route analog signals to dedicated ANx pins to minimize digital noise coupling. Plan power sequencing and decoupling per the family reference manual. This page synthesizes distributor pricing, drop-in PIC24FJ192GA110 family alternatives, and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FJ192GA110-I/PT - 16-Bit MCU 192KB Flash 32MHz | Microchip
PIC24FJ192GA110-I/PT

PIC24FJ192GA110-I/PT - 16-Bit MCU 192KB Flash 32MHz | Microchip

The Microchip PIC24FJ192GA110-I/PT is a 16-bit general-purpose flash microcontroller from the PIC® 24F family, delivering 192KB of program flash memory, 16KB of SRAM, and 32 MIPS performance at 32 MHz in a 100-pin TQFP (12x12 mm) package. It operates from 2.0V to 3.6V with 5.5V-tolerant digital inputs, integrates Peripheral Pin Select (PPS) for flexible digital-function remapping, and ships with a rich connectivity peripheral set including 3x I²C, 3x SPI, 4x UART, and 23 independent timers. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a wide range of peripherals (timers, communication controllers, ADCs, GPIO) on one die. PIC24F microcontrollers sit in Microchip's 16-bit MCU hierarchy above the 8-bit PIC16/PIC18 families and below the 32-bit PIC32MX/dsPIC33 parts. The PIC24FJ192GA110 belongs to the General Purpose (GP) sub-family, optimized for low-power (<100 nA standby) and connectivity-rich designs with peripheral-rich bridging capability. Key differentiating specifications include 192KB self-reprogrammable flash, 16KB SRAM, an 8 MHz internal oscillator with 4x PLL and multiple divide options, a 17-bit single-cycle hardware multiplier, a 16-bit hardware divider, and 16 working registers optimized for the C compiler. The PPS (Peripheral Pin Select) block lets the developer remap most digital peripherals to any compatible digital I/O pin after PCB layout, which dramatically simplifies board routing on dense 100-pin designs and enables easy migration between 64-, 80-, and 100-pin package variants of the same family without firmware changes. The PIC24F core uses a modified Harvard architecture with a 16-bit data path, enabling 32 MHz operation with deterministic interrupt latency suitable for real-time control. On-chip peripherals include brown-out reset, low-voltage detection (LVD), high-current sink/source (18 mA/18 mA) digital I/O, and configurable open-drain outputs. The device supports Sleep, Idle, and Doze power-management modes with fast wake-up to balance responsiveness with battery life in portable or always-on designs. Typical applications include embedded control boards, industrial automation nodes, user-interface modules with multiple displays, low-power sensing nodes, and bridging designs that fan out across several serial buses. The 3x I²C / 3x SPI / 4x UART mix is especially attractive when the design must simultaneously drive a graphics display, several sensors, and a wired uplink. When designing with this MCU, observe the 2.0V to 3.6V supply range, leverage 5.5V-tolerant digital inputs to interface directly to legacy 5V logic, and use PPS to clean up the board layout. If the design is later resized to the 64- or 80-pin package in the same family, PPS allows pinout migration without firmware rework. This page synthesizes distributor pricing, drop-in package alternatives, and practical engineering guidance not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FJ192GA110T-I/PF - 16-bit 32MHz MCU, 192KB Flash, 100-TQFP | Microchip
PIC24FJ192GA110T-I/PF

PIC24FJ192GA110T-I/PF - 16-bit 32MHz MCU, 192KB Flash, 100-TQFP | Microchip

The Microchip Technology PIC24FJ192GA110T-I/PF is a 16-bit PIC24F microcontroller featuring a 32MHz CPU core, 192KB of Flash program memory (organized as 65.5K x 24), and 16KB of RAM, housed in a 100-pin TQFP (14x14) package. It belongs to the PIC24F family with eXtreme Low Power (XLP) technology, delivering <100nA standby current for battery-driven applications. The 'T' suffix indicates Tape & Reel packaging and 'I/PF' denotes the industrial temperature grade in the 100-pin TQFP package. What is a 16-bit MCU? A 16-bit microcontroller (MCU) is an embedded processor with a 16-bit data path, sitting between 8-bit controllers and 32-bit ARM Cortex devices in capability. The PIC24F architecture uses a Modified Harvard RISC design with a 16-bit instruction set, offering up to 16 MIPS throughput while preserving code density advantages of 8-bit PIC devices. Within the broader taxonomy, PIC24F belongs to: MCU -> 16-bit MCU -> Microchip PIC24 family -> PIC24F sub-family -> XLP low-power series. Key features of this part include three I2C buses, three SPI ports, four UART channels, 23 independent timers, and a hardware Real-Time Clock/Calendar (RTCC). It integrates a 16-channel 10-bit ADC capable of 500 ksps, multiple PWM modules, and a charge time measurement unit (CTMU) for capacitive touch sensing. The 100-pin TQFP package provides up to 85 general-purpose I/O pins, allowing extensive peripheral expansion. The part operates from 2.0V to 3.6V and includes a 32kHz secondary oscillator for low-power modes. The XLP technology enables wake-up from <1uA sleep current, critical for IoT battery life. Typical applications include industrial control panels, USB peripherals, graphical displays, sensor hubs, and low-power IoT edge nodes. The abundant RAM and Flash support graphical user interfaces and wireless protocol stacks. The flexible serial connectivity makes it suitable for bridging sensor networks. When designing with this MCU, ensure decoupling: place 100nF ceramic capacitors near each VDD/VCAP pin pair, and use a 10uF bulk capacitor on the main 3.3V rail. Configure the JTAG/ICSP pins according to in-circuit programming requirements to avoid debugger conflicts. This page synthesizes distributor pricing from 4 sources, drop-in alternatives from the PIC24F family in the same 100-TQFP footprint, and practical design notes drawn from the Microchip datasheet and application notes not consolidated in a single product brief.

Cotización Contacto
PIC24FJ192GA110T-I/PT - 16-bit MCU, 192KB Flash, 100-TQFP | Microchip
PIC24FJ192GA110T-I/PT

PIC24FJ192GA110T-I/PT - 16-bit MCU, 192KB Flash, 100-TQFP | Microchip

The Microchip Technology PIC24FJ192GA110T-I/PT is a 16-bit PIC24F microcontroller featuring 192KB of Flash program memory (65.5K x 24), 16KB of RAM, and a 32MHz (16 MIPS) CPU core, housed in a 100-pin TQFP (PT) package with 85 digital I/O pins. The 'T' suffix indicates tape-and-reel packaging, the 'I' indicates the industrial -40C to +85C temperature range, and 'PT' indicates the 100-pin TQFP package. A 16-bit microcontroller (MCU) is a programmable system-on-chip that combines a CPU, memory (Flash and RAM), peripherals, and I/O into a single silicon die. PIC24F devices belong to Microchip's eXtreme Low Power (XLP) family and sit between 8-bit PIC MCUs and 32-bit PIC32 devices in the product hierarchy, optimized for battery-friendly mixed-signal embedded designs. The 16-bit modified Harvard architecture executes instructions in a single cycle (including hardware multiply/divide) at up to 16 MIPS. Key features include 192KB self-reprogrammable Flash, 16KB SRAM, 8MHz internal oscillator with 4x PLL (32MHz system clock), 85 I/O pins with 18mA source/sink capability, three I2C, three SPI, four UART, and 23 independent timers. The operating voltage range of 2.0V to 3.6V and <100nA standby current suit battery-powered applications. Selectable Sleep, Idle, and Doze power-management modes enable aggressive energy budgets, while 5.5V-tolerant digital inputs simplify interfacing to 3.3V rails. The PIC24F core combines a 17-bit single-cycle multiplier and dedicated barrel shifter for DSP-style arithmetic, supporting C compiler code density approaching ARM Cortex-M0 levels while retaining 8-bit PIC ecosystem compatibility. Charge Time Measurement Unit (CTMU) and 12-bit ADC are typical of the GA1xx family, supporting touch sensing and precision analog measurement. Typical applications include industrial control panels, medical instrumentation, low-power sensor hubs, USB/connectivity bridges, graphical user interfaces, and automotive body modules. The high pin count (100 TQFP) makes it suitable for designs needing both generous analog channels and rich digital connectivity. When designing with this device, plan I/O assignments carefully because the GA1xx family multiplexes many peripherals onto the same pins. Always include decoupling capacitors on every VDD/AVDD pin pair and follow Microchip's 100-pin TQFP layout guidelines for thermal dissipation at industrial temperatures. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Cotización Contacto
PIC24FJ192GB106-I/MR - 192KB Flash USB OTG MCU | Microchip
PIC24FJ192GB106-I/MR

PIC24FJ192GB106-I/MR - 192KB Flash USB OTG MCU | Microchip

The Microchip PIC24FJ192GB106-I/MR is a 16-bit microcontroller from the PIC24F family featuring 192KB of Flash program memory, 16KB of RAM, and integrated USB On-The-Go (OTG) full-speed support. The device operates at up to 32MHz (16 MIPS) and is housed in a 64-pin VQFN (9x9 mm) package. Its peripheral set targets low-power connectivity applications requiring multiple serial channels. A microcontroller (MCU) is an integrated circuit that combines a CPU core, program and data memory, plus configurable peripherals on a single silicon die. The PIC24F family uses a 16-bit modified Harvard architecture with one instruction per cycle and 16 working registers, sitting in the performance tier between 8-bit PIC16/PIC18 parts and 32-bit PIC32 parts. The 'FJ' prefix indicates the use of Microchip's eXtreme Low Power (XLP) technology, allowing standby currents below 100 nA, and the 'GB' suffix signals integrated USB-OTG with a dedicated transceiver and pull-up/pull-down resistors. Key specifications include 192KB (65.5K x 24 words) of self-programmable Flash, 16KB of RAM for data buffering, and a USB 2.0 full-speed OTG controller with internal transceiver. The device exposes three I2C, three SPI, four UART channels, 23 independent timers, and an RTCC with calendar mode. The 64-VQFN package provides up to 52 general-purpose I/O pins, all 5V tolerant, supporting PPS (Peripheral Pin Select) for flexible peripheral-to-pin mapping. The PIC24FJ192GB106 architecture combines a 16-bit datapath with 24-bit instruction words, enabling C-friendly addressing and single-cycle hardware multiply. XLP technology supports deep sleep, sleep, and idle modes with on-the-fly wake via RTCC, interrupts, or USB resume signaling. The integrated USB-OTG controller implements session request and host negotiation protocols, allowing the MCU to function as both USB device and limited USB host without an external PHY. Typical applications include USB peripherals (HID, CDC, MSD class devices), low-power sensor hubs with USB charging indication, industrial data loggers with USB mass storage, USB-to-UART/I2C/SPI bridges, and battery-powered IoT terminals. The XLP feature set and integrated USB make the part especially attractive for portable medical, consumer, and point-of-sale products. When designing with this device, ensure the USB VBUS pin is connected through the proper 5V-tolerant network and follow Microchip's USB OTG layout guidelines to minimize EMI. The PPS remap registers must be configured and locked before any peripheral I/O is reliable; consult Microchip application notes for OTG cable detection firmware patterns. This page synthesizes distributor pricing, drop-in same-family and cross-family alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shorten the BOM-evaluation and PCB-validation cycle.

Cotización Contacto
PIC24FJ192GB108-I/PT - 192KB Flash USB MCU 80-TQFP | Microchip
PIC24FJ192GB108-I/PT

PIC24FJ192GB108-I/PT - 192KB Flash USB MCU 80-TQFP | Microchip

The Microchip Technology PIC24FJ192GB108-I/PT is a 16-bit PIC24F microcontroller with 192KB Flash, 16KB RAM, integrated USB On-The-Go (OTG), and a 32MHz CPU core, housed in an 80-pin TQFP (12x12mm) package. Headline parameters: 192KB (65.5K x 24) program Flash, 16KB RAM, 80-TQFP (12x12) package, 2.0V-3.6V Vdd range, and <100nA standby current per the Microchip product family description. A PIC microcontroller (MCU) is a compact integrated circuit containing a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals (timers, UARTs, ADC, communication interfaces). The PIC24F family uses a 16-bit modified Harvard RISC architecture that delivers up to 16 MIPS at 32MHz while retaining the PIC ecosystem's deterministic interrupt model. Within the broader taxonomy, PIC24F devices sit between 8-bit PIC18 and 32-bit PIC32 families, targeting USB-enabled, low-power, mid-complexity embedded designs. Key features include a full-speed USB 2.0 On-The-Go peripheral with integrated transceiver, three I2C, three SPI, four UART channels, 23 independent timers, a 10-bit ADC (typically 16 channels on 80-pin parts), and multiple PWM outputs suitable for motor and lighting control. The 192KB Flash supports large protocol stacks and dual-image bootloaders, while 16KB RAM enables sizeable communication buffers for TCP/IP, USB CDC, or graphics applications. The integrated RTCC and deep-sleep states with nanoWatt technology deliver the <100nA standby current cited in Microchip's product brief. Architecture-wise, the device pairs the PIC24F CPU with separate program and data buses, a hardware multiplier, and DMA-capable peripheral mapping. The USB OTG block includes the physical transceiver and the SIE, eliminating the external PHY; this shortens the BOM for HID, CDC, MSD, and vendor-class designs. The 80-pin TQFP exposes up to 65 general-purpose I/O lines, allowing direct interface to TFT displays, capacitive touch controllers, and external memory. Typical applications include USB peripherals (barcode scanners, POS terminals, data loggers), low-power sensor hubs with USB charging, industrial HMI panels, audio playback docks, and battery-powered instrumentation that benefits from USB connectivity and nanoWatt standby. The wide operating voltage also makes the part well suited to portable medical and consumer accessories. When designing with this MCU, allocate the USB DP/DPU pins carefully and follow Microchip's USB layout guidelines (90-ohm differential, controlled impedance, common-mode choke option for host mode). Verify Vdd rise time and decoupling (typically 100nF + 4.7uF) so the internal regulator settles before the USB transceiver is enumerated. This page synthesizes distributor pricing, validated drop-in alternatives from the PIC24F family, and practical design notes that complement - not duplicate - the manufacturer datasheet.

Cotización Contacto
PIC24FJ192GB108T-I/PT - 16-Bit 32MHz USB OTG MCU, 192KB Flash | Microchip
PIC24FJ192GB108T-I/PT

PIC24FJ192GB108T-I/PT - 16-Bit 32MHz USB OTG MCU, 192KB Flash | Microchip

The Microchip Technology PIC24FJ192GB108T-I/PT is a 16-bit PIC24F microcontroller featuring a 32MHz core, 192KB of Flash program memory (65.5K x 24 words), and 16KB of RAM, housed in an 80-pin TQFP (12x12 mm) package with industrial -40C to +85C temperature rating. The 'T' suffix denotes tape-and-reel packaging and the 'I' suffix indicates industrial temperature range, while 'GB' in the part number identifies the integrated USB On-The-Go (OTG) peripheral that distinguishes this family from the GA-series parts. A 16-bit microcontroller is an embedded processor core that executes instructions on 16-bit-wide data paths, typically based on a RISC architecture. The PIC24F family belongs to Microchip's broader 16-bit MCU hierarchy: PIC24F -> PIC24 -> dsPIC33 (with DSP) -> 16-bit microcontrollers -> microcontrollers -> embedded semiconductors. This 'F' family emphasizes ultra-low-power eXtreme Low Power (XLP) operation with standby current below 100nA, making it a power-optimized mid-tier option between 8-bit PIC16/PIC18 MCUs and high-performance 32-bit PIC32 devices. Key differentiating features of this part include: native USB OTG controller (host + device role), 16KB RAM for large data buffering, three I2C and three SPI peripherals plus four UARTs for rich connectivity, 23 independent timers, and rich analog with 10/12-bit ADC. The 80-TQFP footprint also exposes the parallel master port, allowing connection to external bus peripherals or graphics controllers. The USB OTG capability is the primary reason engineers choose GB-series PIC24F parts over the otherwise-similar GA-series that lacks USB. The part uses Microchip's modified Harvard architecture with a 16-bit instruction word and 24-bit data path, providing up to 16 MIPS performance at 32MHz / 3.3V. XLP technology combined with multiple idle and sleep modes allows battery-powered products to extend operating life; the <100nA standby current enables years of operation from a coin cell when the MCU periodically wakes to sample sensors. Typical applications include USB peripherals (HID, CDC, mass storage), portable medical devices (blood-glucose meters, pulse oximeters), industrial data loggers with USB connectivity, consumer electronics with USB charging and data exchange, and embedded HMI/graphics products that require both USB and the parallel master port. When designing with this part, ensure the on-chip voltage regulator is properly decoupled (the ENVREG pin requires an external capacitor per the datasheet). Plan oscillator and PLL configuration carefully because the 32MHz instruction rate derives from the internal FRC or external crystal/clock, and USB Full Speed (12Mbps) requires a 48MHz USB clock domain. For low-power designs, use the deep-sleep and RTCC modes to drop standby current below 100nA. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet. The PIC24FJ192GB108T-I/PT is part of the PIC24FJxxxGB1xx family with USB OTG and is supplied on tape and reel for high-volume SMT assembly.

Cotización Contacto
PIC24FJ192GB110-I/PT - 16-Bit MCU 192KB Flash USB OTG | Microchip
PIC24FJ192GB110-I/PT

PIC24FJ192GB110-I/PT - 16-Bit MCU 192KB Flash USB OTG | Microchip

The Microchip Technology PIC24FJ192GB110-I/PT is a 16-bit flash microcontroller from the PIC24F family, featuring 192 KB of program Flash, 16 KB of RAM, and integrated USB On-The-Go (OTG) hardware in a 100-pin TQFP (12x12 mm) package. It operates at up to 32 MHz CPU clock, delivering 16 MIPS throughput, and is qualified for the -40C to +85C industrial temperature range. A 16-bit microcontroller is a microprocessor core with a 16-bit data path, 16-bit registers, and a 16-bit ALU, providing a higher performance ceiling than 8-bit cores while remaining significantly simpler and lower-power than 32-bit Cortex-M devices. The PIC24F family sits in Microchip's "peripheral-rich, ultra-low-power" tier of 16-bit MCUs (PIC16-bit -> PIC24 -> dsPIC33 -> dsPIC40) and is widely deployed in consumer, industrial, and USB-connected embedded systems. The PIC24FJ192GB110 variant adds a USB 2.0 OTG full-speed transceiver and a 16 KB RAM buffer suited to USB class stacks. Key features include 192 KB Flash (65.5K x 24 instruction words), 16 KB SRAM, integrated USB OTG with PHY, three I2C, three SPI, four UART, and 23 independent timers. Peripheral pin select (PPS) provides flexible mapping of digital peripherals to I/O pins. The on-chip RTCC and deep-sleep currents under 100 nA enable battery-backed designs. The 100-pin TQFP package exposes up to 84 general-purpose I/O pins. The PIC24FJ192GB110 implements a modified Harvard architecture with a 16-bit data path and 24-bit instruction words, allowing single-cycle MAC operations and deterministic interrupt latency. The integrated USB OTG controller with on-chip PHY eliminates external transceiver parts for many USB device, host, and dual-role applications, and the large 16 KB RAM supports USB class driver buffering without external memory. Typical applications include USB peripherals (HID, CDC, MSD), industrial control with USB diagnostics, USB host mass storage interfaces, low-power sensor hubs, and battery-powered data loggers. The combination of USB OTG, large RAM, and 84 I/O pins makes this part attractive when external bridge ICs would otherwise be needed. When designing with this device, ensure the 2.0-3.6 V supply is well-decoupled near the VDD/VSS pairs and that the USB VBUS pin uses the recommended 10 uF bulk capacitor. The PPS remapping should be configured before enabling peripheral outputs to avoid transient glitches. This page synthesizes distributor pricing, USB OTG-aware drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, supporting faster component selection and BOM risk reduction.

Cotización Contacto
PIC24FJ192GB110T-I/PF - 16-bit 32MHz USB OTG MCU, 192KB Flash | Microchip
PIC24FJ192GB110T-I/PF

PIC24FJ192GB110T-I/PF - 16-bit 32MHz USB OTG MCU, 192KB Flash | Microchip

The Microchip Technology PIC24FJ192GB110T-I/PF is a 16-bit PIC microcontroller built on a Modified Harvard architecture and capable of 16 MIPS operation at 32 MHz, supplied in a 100-pin TQFP (14x14 mm) package. It integrates 192 KB of Flash program memory, 16 KB of RAM, a 17-bit single-cycle hardware multiplier, a 16-bit hardware divider, and a 16-element working register array that the C compiler can target efficiently. The integrated USB On-The-Go (OTG) controller, 8 MHz internal RC oscillator with 4x PLL, and 23 independent timers target low-power connectivity applications requiring multiple serial interfaces (3x I2C, 3x SPI, 4x UART). A PIC24F microcontroller is a 16-bit flash MCU family from Microchip that sits between the 8-bit PIC16/PIC18 families and the 16-bit dsPIC/PIC32 families. It is built on a Modified Harvard architecture with separate program and data buses, enabling single-cycle instruction fetch with data access, while sharing a unified 16-bit instruction set across the family. PIC24F parts are positioned for low-power (<100 nA standby current) embedded designs that need richer peripherals than an 8-bit MCU can deliver but do not require a digital signal processor. Within Microchip's portfolio, PIC24FJ192GB110 belongs to the PIC24F USB family, which adds an integrated USB 2.0 full-speed On-The-Go transceiver to the standard PIC24F feature set. Key features include USB OTG with integrated transceiver, 16 MIPS performance at 32 MHz, low-power nanoWatt XLP technology for <100 nA standby current, and 84 remappable I/O pins via the Peripheral Pin Select (PPS) subsystem. The 16 KB RAM and 192 KB Flash support buffering and large protocol stacks, while 3x I2C, 3x SPI, 4x UART, and 23 timers allow parallel connectivity and control tasks without external peripherals. Real-time clock, comparators, 10-bit ADC (16 channels at 500 ksps), and 16-bit timers reduce external analog and timing component counts. Architecture depth: the device uses a 16-bit data path with separate 24-bit program and 16-bit data buses for the Modified Harvard core, and the C compiler (MPLAB XC16) maps efficiently onto the 16-element working register array. Hardware DSP-like acceleration is provided by a 17-bit x 17-bit single-cycle multiplier and a 16/32-bit hardware divider. The PPS module allows most digital peripherals to be mapped to a wide range of I/O pins at runtime, simplifying PCB routing in densely populated designs. Typical applications include USB human-interface devices (HID) such as keyboards and mice, USB mass storage and CDC devices, embedded web servers and sensor hubs, industrial data loggers with USB diagnostics, low-power battery-powered instrumentation, and consumer audio peripherals that require both USB connectivity and a flexible peripheral set. The automotive/industrial -40C to +85C operating range covers most commercial and industrial environments. When designing with this MCU, ensure USB board layout follows the 90-ohm differential impedance rule for D+/D- and provide a 4.7 kV ESD-protected connector. Configure PPS mappings carefully before locking I/O, and budget Flash endurance to 1000 erase/write cycles typical for the Flash program memory. This page synthesizes drop-in alternatives in the same 100-pin TQFP footprint, current distributor pricing, and practical design notes that go beyond the manufacturer datasheet summary.

Cotización Contacto
PIC24FJ192GB110T-I/PT - 16-bit 32MHz 192KB Flash USB MCU | Microchip
PIC24FJ192GB110T-I/PT

PIC24FJ192GB110T-I/PT - 16-bit 32MHz 192KB Flash USB MCU | Microchip

The Microchip PIC24FJ192GB110T-I/PT is a 16-bit PIC24F microcontroller from the PIC® 24F family, featuring 192 KB of Flash program memory, 16 KB of RAM, integrated USB On-The-Go (OTG), and a maximum CPU speed of 32 MHz, all housed in a 100-pin TQFP (12x12 mm, PT) package. It is part of the PIC24FJxxxGB1xx series, designed for low-power and connectivity applications that need multiple serial interfaces. Background context: A 16-bit microcontroller is an embedded processor with a 16-bit data path and instruction set, sitting architecturally between 8-bit MCUs (lower cost, simpler peripherals) and 32-bit MCUs (higher performance, more memory). Within the PIC family hierarchy, the PIC24F sits below the dsPIC33 and PIC32 families. The "FJ" prefix denotes Flash program memory with the nanoWatt XLP low-power technology; "GB" indicates integrated USB OTG with on-chip transceiver. PIC24F MCUs are widely used in human-interface devices, USB peripherals, and industrial control where USB connectivity plus low standby current (<100 nA) matter. Key features include 192 KB Flash (65.5K x 24), 16 KB RAM, integrated USB 2.0 OTG with on-chip transceiver, three I²C, three SPI, four UART ports, 23 independent timers, and nanoWatt XLP technology with sub-100 nA standby current. The 100-pin TQFP (PT) package exposes all of these peripherals plus a parallel master port for external memory or graphics interfacing. At 32 MHz core speed the device delivers approximately 16 MIPS of throughput, with instruction cycles that complete in two clock periods. The PIC24F core uses a 16-bit modified Harvard architecture with a hardware multiplier for DSP-like operations. Power management includes multiple idle and sleep modes (Sleep, Idle, Doze, Alternate Run), a real-time clock calendar (RTCC) with on-chip 32 kHz oscillator, and integrated LDO regulator for single 2.0-3.6 V supply operation. Typical applications include USB peripherals such as mass storage, HID, CDC, and audio class devices; industrial data loggers; medical instrumentation; graphic LCD/OLED controllers with the parallel master port; and battery-powered sensors needing <100 nA standby. Designers frequently pair the PIC24FJ192GB110 with external PHY-less USB connectors and FTDI-style serial bridges, or use it as a USB host for mass storage. Design consideration: The PIC24FJ192GB110 family requires careful attention to USB bus impedance (90 ohm differential) on D+/D- traces and decoupling capacitor placement near the VUSB3V3 pin. The 100-pin TQFP footprint (12x12 mm) is large enough to support four-layer PCB routing; however, leaving the parallel master port unused frees significant board space on simpler designs. Unique value: This page consolidates distributor pricing, exact drop-in Microchip alternatives from the same family, and practical PCB/design notes derived from Microchip's datasheet and reference designs - information not collected together on any single distributor product page.

Cotización Contacto
PIC24FJ256DA106-I/MR - 256KB Flash 16-Bit MCU with Graphics & USB | Microchip
PIC24FJ256DA106-I/MR

PIC24FJ256DA106-I/MR - 256KB Flash 16-Bit MCU with Graphics & USB | Microchip

The Microchip Technology PIC24FJ256DA106-I/MR is a 16-bit microcontroller with integrated graphics acceleration, a display controller, and USB 2.0 full-speed on-the-go (OTG) support, packaged in a 64-pin VQFN (9x9 mm) exposed-pad land grid. It belongs to the PIC24F-DA family and is built around the PIC24F core that delivers up to 16 MIPS at 32 MHz while consuming as little as 1 mA/MIPS. The device integrates 256 KB of self-programmable Flash, 24 KB of SRAM, a 10-bit 1.1 Msps ADC with up to 16 channels, two UART modules, two SPI modules, and two I2C modules. A 16-bit microcontroller (MCU) is a single-chip computer that uses a 16-bit-wide data path, registers, and ALU, offering a balance between 8-bit simplicity and 32-bit performance. Within Microchip's taxonomy, the PIC24F sits above 8-bit PIC10/12/16 devices and below 32-bit PIC32 devices; it is a low-power, Flash-based family with strong peripheral integration. The PIC24FJ256DA106 belongs to the PIC24F-DA subfamily, which adds graphics-specific hardware for driving TFT LCDs up to 4.3" WQVGA (480 x 272) without an external graphics controller, and to the Power Management IC, peripherals and broader ecosystem. Key features: integrated Graphics Controller with hardware acceleration and up to 480x272 WQVGA drive, integrated 3.3V LDO regulator, USB 2.0 full-speed OTG with on-chip transceiver, Charge Time Measurement Unit (CTMU) supporting up to 64 touch buttons, Parallel Master Port (PMP), Real-Time Clock and Calendar (RTCC), and 8-channel hardware DMA. The device operates from 2.0 V to 3.6 V with industrial -40C to +85C temperature range. The PIC24FJ256DA106's architecture combines a 16-bit modified Harvard RISC core with a 24-bit instruction word, achieving deterministic interrupt latency. The Graphics Controller features a dedicated DMA-driven rendering pipeline and configurable display timing, eliminating the need for external display controllers and BOM cost. The integrated Charge Time Measurement Unit (CTMU) provides capacitive touch sensing, while the Parallel Master Port enables direct connection to external memory or graphics peripherals. Typical applications include 4.3-inch WQVGA TFT LCD display modules with touch, USB-enabled embedded human-machine interfaces (HMIs), industrial control panels with graphical readout, point-of-sale (POS) terminals, medical instrumentation displays, and consumer appliance user interfaces. The device suits any product that benefits from integrated graphics acceleration, USB connectivity, and Microchip's extensive development ecosystem including MPLAB X IDE, MPLAB Harmony framework, and Explorer 16/32 development board support. When designing with this MCU, allocate the VQFN-9x9 exposed pad (EP) to a continuous ground plane with multiple thermal vias to the inner ground layer for optimal thermal and electrical performance. The USB transceiver requires a precise 48 MHz clock that can be derived from the PLL with a low-jitter crystal reference; engineers should use an external ESD protection array on the USB DP/DM lines and a 2.5 kohm pull-up on D+ for full-speed signaling. Avoid routing high-speed traces near the analog AVdd rail. This page synthesizes Microchip PIC24FJ256DA106-I/MR distributor pricing, 256 KB flash memory code density, and 16 MIPS throughput at 3.3 V ratings with drop-in VQFN-64 (9x9) alternatives and practical design notes not found in the manufacturer datasheet alone.

Cotización Contacto
PIC24FJ256DA106-I/PT - 256KB Flash 16-Bit MCU with Graphics | Microchip
PIC24FJ256DA106-I/PT

PIC24FJ256DA106-I/PT - 256KB Flash 16-Bit MCU with Graphics | Microchip

The Microchip PIC24FJ256DA106-I/PT is a 16-bit microcontroller from the PIC24F-DA family with integrated graphics acceleration, a display controller, and USB On-The-Go (OTG), packaged in a 64-pin TQFP (10x10 mm). It runs at 32 MHz delivering up to 16 MIPS, integrates 256 KB Flash program memory organized as 85.5K x 24, and is engineered to directly drive displays up to 4.3" WQVGA at 480 x 272 resolution without an external graphics controller. The device is supplied in an industrial-grade -40C to +85C temperature range, denoted by the "/PT" TQFP-64 package code. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), and a rich set of peripherals on one die. The PIC24F family uses a modified Harvard architecture running a 16-bit instruction word with a 16-bit working register array, a 17-bit x 17-bit single-cycle hardware multiplier, and a hardware 16/16-bit divider. The 'DA' sub-family extends the base 'GA' general-purpose line by adding a dedicated graphics display controller, a parallel graphics port (EPMP/GFX), and USB OTG - targeting cost-sensitive graphical HMI products where bill-of-materials pressure rules out an external GPU. Key features of this device include 256 KB self-programmable Flash with code-guard security, 24 KB SRAM, an 8 MHz internal oscillator with 4x PLL (yielding the 32 MHz CPU clock), a Charge Time Measurement Unit (CTMU) for capacitive touch sensing on up to 64 buttons, Peripheral Pin Select (PPS) that remaps digital peripherals to almost any I/O, and multiple serial interfaces (UART, SPI, I2C). The CTMU and PPS combination is what allows the PIC24FJ256DA106 to replace dedicated touch controllers and external pin-mux chips in cost-optimised designs. Architecturally the part combines a C-compiler-optimized RISC engine with the EPMP graphics engine, a DMA controller, a 16-bit timer/counter bank, a 10-bit 500 ksps ADC (typically 16 channels on the 64-pin device), and a USB 2.0 full-speed OTG transceiver. The integrated graphics block accelerates line draw, blit, text render, and alpha blending in hardware, offloading the CPU and enabling smooth GUI refresh at 60 Hz on WQVGA panels. The 32 MHz CPU core executes most instructions in one cycle, so the DMA + EPMP pair can sustain pixel throughput without CPU intervention. Typical applications for the PIC24FJ256DA106-I/PT include low-cost graphical user interfaces on home appliances, white-goods control panels, industrial operator terminals, medical bedside displays, USB-connected point-of-sale terminals, and any embedded product needing a color TFT (up to 4.3" WQVGA) with capacitive touch without paying for a separate graphics controller IC. When designing with this device, observe Microchip's recommended decoupling (100 nF ceramic on every VDD/VSS pair), keep the PLL filter network short, and reserve a programming/debug pin pair for ICSP. The on-chip 3.3V LDO regulator requires its own bulk capacitor and a ferrite bead if the analog supply is noise-sensitive. For CTMU-based touch, the PCB layout and ground flood directly affect measurement repeatability. This page synthesizes XAIPART distributor pricing, drop-in TQFP-64 alternatives from the PIC24FJ family, and practical hardware design notes that complement (not duplicate) the manufacturer datasheet.

Cotización Contacto
PIC24FJ256DA106T-I/MR - 16-bit 32MHz 256KB Flash MCU | Microchip
PIC24FJ256DA106T-I/MR

PIC24FJ256DA106T-I/MR - 16-bit 32MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC24FJ256DA106T-I/MR is a 16-bit PIC microcontroller from the PIC24F family, featuring a 32 MHz core (16 MIPS) with 256 KB of Flash program memory organized as 85.5K x 24 bits and 24 KB of RAM, housed in a 64-pin VQFN (9x9 mm) package. It integrates a USB 2.0 full-speed controller and an on-chip graphics controller with dedicated peripherals targeted at embedded graphical user interfaces, making it one of the few PIC24 devices combining high code density, native USB, and direct display driving on a single die. A 16-bit microcontroller (MCU) is a microprocessor integrating CPU core, memory, peripherals, and I/O on one chip; the PIC24F family uses a modified Harvard architecture with a 16-bit data path, 24-bit instruction word, and a C-compiler-optimized instruction set. PIC24F devices sit in the 16-bit MCU hierarchy between 8-bit PIC10/12/16 and 32-bit PIC32, targeting low-power, moderate-performance embedded applications where 32-bit overhead is not justified. The 'FJ' suffix denotes Flash with enhanced peripherals, while 'DA' specifically identifies the integrated graphics controller and USB OTG controller. Designers select PIC24F for deterministic real-time performance, mature MPLAB X toolchain support, and a wide operating voltage range of 2.0V-3.6V. Key features include 256 KB self-programmable Flash, 24 KB SRAM, USB 2.0 full-speed OTG, Parallel Master Port (PMP) for direct graphics interface, on-chip Charge Time Measurement Unit (CTMU) for touch sensing, Peripheral Pin Select (PPS) for flexible I/O mapping, 16-channel 10-bit ADC, five 16-bit timers, and three UART/SPI/I2C modules. The internal 8 MHz oscillator with 4x PLL provides flexible clock options without external crystals for many designs. Typical applications include embedded color graphical displays (TFT-LCD), USB peripherals (HID, CDC, MSD), industrial control panels with touch sensing, low-cost medical devices, home appliance HMIs, and POS terminals. The wide memory and graphics capabilities make it suited to designs that previously required separate LCD controllers and external memory. A key design consideration is the trade-off between integrated graphics versus a discrete graphics controller: the on-chip GPU reduces BOM cost but requires careful PMP timing configuration. Designers should also ensure decoupling per the datasheet's power-section guidelines to maintain USB signal integrity.

Cotización Contacto
PIC24FJ256DA106T-I/PT - 16-bit MCU, 256KB Flash, USB OTG | Microchip
PIC24FJ256DA106T-I/PT

PIC24FJ256DA106T-I/PT - 16-bit MCU, 256KB Flash, USB OTG | Microchip

The Microchip PIC24FJ256DA106T-I/PT is a 16-bit PIC24F microcontroller with 256KB of Flash program memory and an integrated graphics controller with USB On-The-Go (OTG) support, housed in a 64-pin TQFP (10x10 mm) package. According to the Microchip datasheet family DS39905 (408-page device datasheet for the PIC24FJ256DA106 family), it operates at 32 MHz delivering up to 16 MIPS, integrates 24 KB of RAM, and provides a rich peripheral set including 3x I2C, 3x SPI, UART/USART, IrDA, and USB OTG. A PIC microcontroller (MCU) is a compact, self-contained computing device integrating a CPU core, Flash program memory, SRAM, EEPROM, and configurable peripherals (timers, ADC, communication controllers) into a single IC. The PIC24F sub-family uses a 16-bit modified Harvard architecture with RISC instruction set, optimized for low-power and mixed-signal embedded designs. PIC24F sits in the hierarchy MCU -> microcontroller -> embedded processor -> semiconductor, and PIC24FJ adds Flash program memory plus the J (J-series) low-power enhancements. The DA1-series integrates a dedicated graphics controller, reducing CPU overhead for TFT panels, while GB1/DA1 parts add USB OTG for device/host peripherals. Key features of the PIC24FJ256DA106T-I/PT include 256 KB self-programmable Flash, 24 KB SRAM, hardware multiplier (16x16 in one cycle), 8-channel 10-bit ADC, RTCC, and parallel master port (PMP) for graphics data. The device supports 2.0V-3.6V operation, nanoWatt deep-sleep with sub-uA standby, and CTMU for capacitive touch. The 64-pin TQFP package exposes up to 52 digital I/O pins for ample user-interface expansion. Typical applications include graphical human-machine interface (HMI) panels, USB consumer peripherals (HID/composite device), industrial control displays, medical bedside terminals, and battery-powered instrumentation with segmented or TFT graphical feedback. Design considerations: supply decoupling per Microchip AN585 (0.1 uF + 10 uF tantalum near VDD), trace length matching on PMP/graphics bus, and proper VCAP connection for the internal regulator.

Cotización Contacto
PIC24FJ256DA110-I/BG - 16-Bit 32MHz MCU 256KB Flash Graphics TFBGA-121 | Microchip
PIC24FJ256DA110-I/BG

PIC24FJ256DA110-I/BG - 16-Bit 32MHz MCU 256KB Flash Graphics TFBGA-121 | Microchip

The Microchip PIC24FJ256DA110-I/BG is a 16-bit RISC microcontroller in the PIC24F family featuring an integrated graphics controller, USB On-The-Go (OTG), and 256 KB (85.5K x 24 instruction words) of flash program memory, packaged in a 121-ball TFBGA measuring 10 x 10 mm. It executes instructions at up to 32 MHz, providing roughly 16 MIPS of throughput, integrates 24 KB of SRAM, and directly drives displays up to 4.3-inch WQVGA at 480 x 272 resolution through its hardware graphics accelerator without taxing the CPU. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, working RAM, and a rich set of peripherals such as timers, ADC, communication controllers, and GPIO. The PIC24FJ256DA110 belongs to the PIC24F family of low-power 16-bit flash microcontrollers, which sits in Microchip's broader 16-bit MCU portfolio; this hierarchy is PIC24F -> PIC24 -> 16-bit MCU -> microcontroller -> embedded computing -> semiconductor. The 'DA' sub-family is the one that adds the dedicated graphics controller and the 'GB' sub-family adds USB OTG; together the DA family targets graphical user-interface applications. Key differentiating features of the PIC24FJ256DA110-I/BG include its on-chip 3-layer graphics controller with hardware acceleration for line, rectangle, and text rendering; a charge time measurement unit (CTMU) for touch sensing; an integrated full-speed USB 2.0 OTG controller; and Microchip's Peripheral Pin Select (PPS) which remaps most digital peripherals to a wide choice of I/O pins. The device also integrates a 16-channel 10-bit ADC, multiple UART/SPI/I2C peripherals, a Real-Time Clock and Calendar (RTCC), and a JTAG interface for boundary scan and In-Circuit programming. Typical applications for the PIC24FJ256DA110-I/BG are color TFT-LCD graphical user interfaces, industrial HMI panels, USB-equipped data loggers, medical patient-interface displays, and consumer appliances requiring a small color screen. Its 32 MHz core plus 256 KB flash is sized for storing full graphical framebuffers plus application code, while the 121-ball BGA enables compact board layouts where board area is at a premium. When designing with this part, allocate sufficient PCB area for BGA fan-out and follow Microchip's recommended land pattern; the 'I' suffix denotes the -40C to +85C industrial temperature range and '/BG' specifies the 121-ball TFBGA package. This page synthesizes distributor pricing, drop-in alternatives, comparison data, and practical design notes for the PIC24FJ256DA110-I/BG that are not aggregated in any single manufacturer datasheet.

Cotización Contacto
PIC24FJ256DA206-I/MR - 16-Bit MCU, 256KB Flash, Graphics+USB, 64-VQFN | Microchip
PIC24FJ256DA206-I/MR

PIC24FJ256DA206-I/MR - 16-Bit MCU, 256KB Flash, Graphics+USB, 64-VQFN | Microchip

The Microchip Technology PIC24FJ256DA206-I/MR is a 16-bit PIC24F microcontroller with integrated graphics controller and USB On-The-Go (OTG) support, operating at up to 32 MHz (16 MIPS) with 256 KB Flash and 96 KB RAM in a 64-pin VQFN (9x9 mm) package. The -I suffix denotes the -40C to +85C industrial temperature range, while the /MR suffix indicates the QFN-64 (9x9) tape-and-reel packaging variant. What is a PIC24F microcontroller? The PIC24F is a 16-bit modified Harvard architecture MCU family from Microchip Technology that combines high-performance 16 MIPS processing with ultra-low-power features. PIC24F sits within the broader PIC microcontroller hierarchy: PIC microcontroller -> 16-bit MCU -> PIC24 family -> PIC24F subfamily -> PIC24FJ-DA graphics series. The DA-series is purpose-built for graphical user interfaces, integrating a dedicated display controller and graphics accelerator. Key features include 52 general-purpose I/O pins, a 17-bit single-cycle hardware multiplier, a 16-bit hardware divider, an 8 MHz internal oscillator with 4x PLL, multiple clock divide options, and an integrated display controller capable of driving displays up to 4.3-inch WQVGA (480x272 pixels). The integrated graphics acceleration engine offloads common drawing primitives from the CPU, enabling smoother UI performance. USB On-The-Go (OTG) provides host, device, and dual-role USB operation without an external PHY. Typical applications include graphical HMI displays, point-of-sale terminals, medical device interfaces, industrial control panels, automotive infotainment clusters, and USB-connected embedded devices requiring rich on-screen graphics. The combination of USB OTG, large RAM (96 KB), and integrated graphics acceleration makes this device well suited to graphical interface products that benefit from BOM consolidation. When designing with this part, ensure the 2.2V to 3.6V supply rail is well decoupled near the VDD/VSS pin pairs, and follow Microchip's recommended trace impedance for the high-speed USB DP/DM lines. The 9x9 mm QFN package requires thermal vias under the exposed pad for proper heat dissipation at full 32 MHz operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. XAIPART maintains the inventory and lifecycle data; consult the official Microchip datasheet for electrical characteristics and programming specifications.

Cotización Contacto