Microcontroladores

PIC32MX664F064L-V/BG

PIC32MX664F064L-V/BG - 80MHz 32-bit MIPS MCU USB OTG TFBGA-121 | Microchip

The Microchip PIC32MX664F064L-V/BG is a 32-bit MIPS microcontroller from the PIC32MX5/6/7 family, featuring a MIPS32 M4K core running at 80 MHz (105 DMIPS), 64 KB of Flash program memory and 32 KB of SRAM, integrated USB 2.0 On-The-Go with on-chip PHY, a 10/100 Ethernet MAC, a 10-bit 1 Msps ADC, and four dedicated DMA channels, all housed in a 121-ball 10x10 mm TFBGA package with industrial-grade -40C to +105C operating range. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a high-performance processor core, program and data memory, and programmable peripherals around a unified system bus. Within the broader semiconductor taxonomy, MCUs belong to the integrated circuits family, and 32-bit variants such as the PIC32MX sit above 8-bit and 16-bit microcontrollers in processing performance while retaining deterministic real-time behavior. The PIC32MX6xx sub-family specifically targets USB- and Ethernet-connected embedded designs where on-chip connectivity peripherals eliminate the need for external PHY or MAC chips. Key differentiating features of this part include the integrated USB 2.0 On-The-Go transceiver with PHY, a 10/100 Mbps Ethernet MAC with MII/RMII interfaces, the MIPS16e code-compression mode that reduces code size up to 40 percent, a 5-stage pipelined Harvard architecture, and four DMA channels optimized for USB OTG throughput. The on-chip 10-bit 1 Msps ADC and the configurable 16-bit timer/capture/compare/PWM modules further extend its applicability to mixed-signal designs. In terms of architecture, the M4K core implements a 5-stage pipeline with separate instruction and data buses (Harvard), branch delay slots handled in hardware, and a Multiply/Divide unit that executes 32x16 MACs in one cycle. The memory map places 64 KB of Flash and 32 KB of SRAM on the same bus, with Flash prefetch and wait-state generation handled transparently. Code development is supported through Microchip's MPLAB X IDE and the MPLAB Harmony framework, both of which provide peripheral libraries, USB and TCP/IP stacks, and real-time operating system options. Typical applications include industrial USB peripherals such as data loggers and POS terminals, 10/100 Ethernet-enabled embedded nodes, USB OTG device/host bridges, CAN-bus interface cards, and connectivity-rich consumer devices that need simultaneous USB and Ethernet operation. The wide peripheral set also suits motor-control front ends and human-machine interface panels. When designing with this device, allocate adequate decoupling on every AVDD/VDD pair, respect the 121-ball TFBGA PCB layout rules (0.8 mm pitch, microvia-friendly fanout), and use the on-chip regulator decoupling guidelines from the datasheet to keep core and I/O rails clean during USB Full-Speed transitions. This page synthesizes current distributor pricing, drop-in same-brand alternatives, and practical design notes that are not aggregated in any single manufacturer datasheet or distributor listing, giving engineers a one-stop reference for the PIC32MX664F064L-V/BG.

USD $4,25 En stock

PIC32MX664F064L-V/PT

PIC32MX664F064L-V/PT - 80MHz 32-bit MCU 64KB Flash | Microchip

The Microchip Technology PIC32MX664F064L-V/PT is a 32-bit MIPS32 M4K microcontroller operating at 80 MHz with 64 KB Flash and 32 KB SRAM, housed in a 100-pin TQFP (12x12 mm) package. It belongs to the PIC32MX5/6/7 family which integrates 10/100 Mbit Ethernet MAC, USB On-The-Go (OTG), and 10-bit ADC peripherals for embedded connectivity applications. A PIC32MX microcontroller is a 32-bit MIPS-based MCU from Microchip that bridges the gap between 8/16-bit PIC microcontrollers and the higher-performance MIPS cores used in networking and graphics applications. PIC32MX sits within the broader taxonomy of: microcontroller (MCU) -> 32-bit MCU -> MIPS32 MCU -> embedded connectivity MCU -> semiconductor IC. It is supported by the MPLAB Harmony integrated software framework, which provides peripheral drivers, middleware (TCP/IP, USB, graphics), and RTOS integration to accelerate firmware development. Key features of the PIC32MX664F064L-V/PT include: 64 KB Flash program memory, 32 KB SRAM, 10-bit 1 Msps ADC with up to 16 channels, USB 2.0 Full-Speed OTG, 10/100 Ethernet MAC, multiple UART/SPI/I2C interfaces, 5 16-bit timers/counters, and 5 IC/OC/PWM modules. The V temperature grade indicates -40C to +105C operation suitable for industrial environments, and the /PT suffix denotes the 100-pin TQFP package. The architecture uses the MIPS32 M4K core with single-cycle multiply, hardware multiply-accumulate (MAC), and a 5-stage pipeline, enabling 80 DMIPS performance at 80 MHz. The 32-bit instruction path and 32-bit data path are bridged to 16-bit and 32-bit peripherals, balancing computational throughput with peripheral flexibility. Typical applications include industrial Ethernet connectivity nodes, USB peripherals and embedded hosts, data loggers, building automation gateways, low-cost graphic HMI displays, and point-of-sale terminals. The combination of integrated Ethernet and USB OTG makes it especially well-suited for IoT edge nodes requiring multiple wired connectivity options on a single chip. When designing with this part, pay attention to the decoupling network: place 100 nF X7R capacitors close to every VDD/VSS pair, add a bulk 4.7-10 uF tantalum on the main rail, and ensure the VCAP/VDDCORE pin has a low-ESR 10 uF ceramic. The 80 MHz maximum frequency requires careful PCB layout to keep trace lengths short for the crystal and Ethernet signals. This page synthesizes distributor pricing (as of 2026-10-03), drop-in alternatives within the same 100-pin TQFP footprint, and practical design notes not found in the manufacturer datasheet - giving engineers a faster path from part selection to prototype.

USD $4,12 En stock

PIC32MX664F064LT-I/BG

PIC32MX664F064LT-I/BG - 80MHz 32-bit MCU, 64KB Flash, USB/Ethernet, 121-TFBGA

The Microchip Technology PIC32MX664F064LT-I/BG is a 32-bit MIPS M4K microcontroller operating at up to 80 MHz with 64 KB of Flash program memory and 32 KB of RAM, housed in a 121-ball TFBGA (10x10 mm) package. It is part of the PIC32MX5/6/7 family that integrates a 10/100 Mbit Ethernet MAC, USB 2.0 Full-Speed On-The-Go, four DMA channels, and a 16-bit parallel master port alongside 53 general-purpose I/O pins, making it one of the highest-integration 32-bit PIC microcontrollers in the legacy MX5/6/7 generation. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), working memory (RAM), and configurable peripherals onto one die, forming the smallest addressable computing unit in an embedded system. The PIC32MX family sits in Microchip's mid-range 32-bit MCU portfolio, slotting above the PIC24/dsPIC families and below the Cortex-M-class PIC32MZ/MK families in performance and price. Within this taxonomy, the PIC32MX664F064LT-I/BG belongs to the "MX664" sub-line that specifically targets connected-embedded applications requiring both USB device/host and Ethernet connectivity on the same silicon. Key features of this device include a 32-bit MIPS M4K core with single-cycle multiply and hardware divide, 64 KB single-voltage Flash, 32 KB SRAM, 53 GPIO, four DMA channels, two I2C, two SPI, two UART, USB 2.0 Full-Speed OTG, 10/100 Ethernet MAC (requires external PHY), 16-channel 10-bit ADC, five 16-bit timers/counters, real-time clock, and a 16-bit parallel master port. The operating voltage range is 2.3 V to 3.6 V, and the industrial temperature range of -40 C to +85 C (denoted by the "I" suffix) covers harsh embedded environments. The PIC32MX664F064LT-I/BG utilizes the MIPS M4K core architecture with separate 32-bit instruction and data paths, a 5-stage pipeline, and a hardware multiply/divide unit that delivers 1.56 DMIPS/MHz. The 121-ball TFBGA package (BG suffix) supports the highest pin-count option in this family, exposing all peripherals and the full 53 GPIO without pin reuse conflicts, and is targeted at space-constrained surface-mount designs. Typical applications include industrial Ethernet gateways, USB-to-UART bridges, home-automation controllers, embedded web servers, networked sensor hubs, point-of-sale terminals, and connected medical devices. The combination of integrated Ethernet MAC and USB OTG on one device is uncommon in this price tier and makes the part especially attractive for low-cost IoT edge nodes. When designing with this part, allocate adequate PCB area for the BGA breakout, ensure proper decoupling (one 0.1 uF per power pin is recommended), and verify that the selected external Ethernet PHY is RMII/MII-compatible with the MX5/6/7 MAC interface. For users migrating from PIC24 or earlier PIC32MX3/4 devices, the peripheral library in MPLAB Harmony provides drop-in driver compatibility.

USD $4,83 En stock

PIC32MX664F064LT-I/PF

PIC32MX664F064LT-I/PF - 80MHz 64KB Flash MCU | Microchip

The Microchip PIC32MX664F064LT-I/PF is a 32-bit MIPS M4K microcontroller from the PIC32MX5/6/7 family, integrating 64KB Flash, 32KB RAM, and 10/100 Mbit Ethernet MAC in a 100-pin TQFP (14x14 mm) package. Operating at 80 MHz with a 3.3V supply, the device delivers high-performance MIPS32 processing with on-chip USB, Ethernet, and CAN peripherals for connected embedded designs. The 'L' in the Part marking denotes an industrial temperature grade of -40C to +85C, while 'T' indicates tape-and-reel packaging. A microcontroller (MCU) is an integrated circuit that combines a processor core, non-volatile program memory (Flash), volatile working memory (RAM), and programmable peripherals in a single chip. Within the semiconductor hierarchy, an MCU sits under microcontrollers, which themselves belong to embedded ICs and broader integrated circuits. The PIC32MX6xx family specifically targets connected applications, adding full-speed USB 2.0 device/host/OTG, 10/100 Ethernet MAC, and CAN 2.0B peripherals alongside the standard UART, SPI, I2C, ADC, and timer blocks. Key features of the PIC32MX664F064LT-I/PF include 64KB (64K x 8) Flash program memory, 32KB (32K x 8) SRAM, four 16-bit timers, five 16-bit compare/PWM outputs, a 10-bit 1 Msps ADC with up to 16 channels, two I2C, two SPI, two UART modules, full-speed USB OTG, an integrated Ethernet MAC, and a 4-channel DMA controller. The M4K core implements the MIPS32 instruction set with single-cycle multiplication and hardware multiply-accumulate, delivering 1.56 DMIPS/MBSi at 80 MHz while consuming only a few tens of milliamps in active mode. Typical applications include industrial Ethernet nodes, USB device controllers, web-enabled sensors, point-of-sale terminals, building automation gateways, and serial-bridge converters. The integrated Ethernet and USB OTG controllers significantly reduce BOM cost compared with external PHY and bridge IC designs, while the 100-pin TQFP exposes enough I/O for color LCD panels, keypads, and sensor arrays. Design considerations: provide a clean low-impedance ground plane, route the 80 MHz crystal traces symmetrically with guard rings, and add 100 nF decoupling near every VDD/AVDD pin. The Ethernet MAC requires an external PHY (such as the Microchip KSZ8041) and 49.9 ohm 1% termination resistors on the differential pairs. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that supplement the manufacturer datasheet.

USD $4,42 En stock

PIC32MX664F064LT-I/PT

PIC32MX664F064LT-I/PT - 80MHz 64KB Flash MCU with USB/Ethernet | Microchip

The Microchip Technology PIC32MX664F064LT-I/PT is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 64 KB of Flash program memory and 32 KB of SRAM, integrated into the PIC32MX5/6/7 connectivity family. Housed in a 100-pin TQFP (PT) package measuring 12x12x1 mm, this industrial-temperature-grade MCU combines a full-speed USB 2.0 device/host/OTG controller, a 10/100 Mbit Ethernet MAC, 4 DMA channels and a rich set of analog and digital peripherals for connected embedded designs. A 32-bit microcontroller (MCU) is a single-chip processor whose data path, ALU and registers are 32 bits wide, allowing it to address large contiguous memory spaces and execute richer instruction sets than 8-bit or 16-bit MCUs. The PIC32MX family sits in the hierarchy MCU -> 32-bit MCU -> MIPS32 M4K core -> PIC32MX connectivity series -> semiconductor, with the 664F064L variant belonging to the higher-pin-count, connectivity-rich branch. Embedded 32-bit MCUs like this one are typically the highest-level decision-making element in an IoT or industrial node, sitting above the sensor interface, power management, and memory circuit blocks on the system block diagram. Key features include 64 KB (64K x 8) Flash, 32 KB SRAM, an internal oscillator, up to 53 user I/O pins (note: some sources cite 53, the 100-pin TQFP exposes this many general-purpose lines), 4 DMA channels for low-CPU-overhead data movement, a 10-bit A/D converter with up to 16 channels, two I2C, two SPI, two UART and a parallel master port. The integrated 10/100 Ethernet MAC and USB 2.0 full-speed controller are the defining connectivity features of the PIC32MX5/6/7 series, eliminating the need for an external PHY in many low-cost node designs when paired with an external Ethernet PHY. Typical applications include industrial Ethernet sensors, USB-enabled data loggers, building-automation controllers, embedded web servers, Modbus TCP gateways, and POS terminals. Engineers should pay attention to the maximum I/O count (53) versus the 100-pin package, indicating dedicated supply, ground and oscillator pins occupy the remaining pins. Firmware development is supported by MPLAB X IDE and the MPLAB Harmony framework, which provides TCP/IP stacks, USB stacks and graphics libraries. A key design consideration is that the LT suffix denotes tape-and-reel packaging for high-volume assembly, and the /PT indicates the 100-pin TQFP - both must be confirmed in the part number before sourcing. The device is supported by MPLAB Harmony libraries which include TCP/IP, USB and graphics middleware. This page synthesizes distributor pricing, verified drop-in alternatives, and practical design notes drawn from the Microchip datasheet, going beyond what the manufacturer datasheet alone provides for sourcing decisions.

USD $4,55 En stock

PIC32MX664F064LT-V/PF

PIC32MX664F064LT-V/PF - 32-bit MCU 64KB Flash USB TQFP-100

The Microchip Technology PIC32MX664F064LT-V/PF is a 32-bit MIPS32 M4K microcontroller integrating 64KB of Flash and 32KB of SRAM with USB On-The-Go, 10-bit ADC, DMA, and 80 MHz CPU clock, housed in a 100-pin TQFP (14x14 mm) package with industrial-grade temperature rating. A PIC32 microcontroller is a 32-bit MCU based on the MIPS32 M4K core, designed by Microchip Technology as a high-performance extension of the 8/16-bit PIC family. PIC32MX devices sit in the broader taxonomy of: microcontroller -> embedded MCU -> 32-bit MCU -> MIPS-based MCU -> mixed-signal controller with USB. The 664 series specifically integrates USB OTG and Ethernet MAC support, making it suitable for connected embedded applications. PIC32MX devices run the MPLAB Harmony and MPLAB XC32 toolchains and are programmed via standard MIPS JTAG/ICSP interfaces. Key features of the PIC32MX664F064LT-V/PF include 64KB Flash program memory, 32KB SRAM, 83 general-purpose I/O pins, a 10-bit 1 Msps ADC with up to 16 channels, USB 2.0 full-speed OTG controller, peripheral pin select (PPS) for flexible signal routing, five 16-bit timers/counters, two I2C, two SPI, and two UART modules. The 80 MHz core delivers up to 1.56 DMIPS/MHz (approximately 125 DMIPS total) and supports single-cycle multiply and hardware divide. The architecture uses a 5-stage MIPS32 pipeline with separate instruction and data Flash buses for zero-wait-state execution from on-chip Flash at 80 MHz. The integrated DMA controller moves data between peripherals and memory without CPU intervention, freeing MIPS for application code. The USB OTG controller with integrated PHY eliminates the need for an external transceiver. Typical applications include USB peripherals and human-interface devices (HID), embedded Ethernet-connected sensors, industrial control and HMI panels, data loggers, point-of-sale terminals, and medical instruments requiring USB connectivity. The wide 2.3V to 3.6V supply range supports battery-powered and 3.3V regulated systems. Design consideration: the 100-pin TQFP footprint requires careful PCB layout, with 0.5 mm pitch and exposed thermal pad handling. Decoupling capacitors should be placed close to each VDD/VSS pair, and the USB DP/DM traces must be routed as a 90-ohm differential pair per USB 2.0 specification. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $4,10 En stock

PIC32MX664F128H-V/MR

PIC32MX664F128H-V/MR - 32-bit MCU 128KB Flash USB OTG 80MHz

The Microchip Technology PIC32MX664F128H-V/MR is a 32-bit MIPS M4K microcontroller with 128KB Flash and 32KB SRAM, USB OTG, 10/100 Ethernet MAC, and a maximum CPU speed of 80 MHz, housed in a 64-pin VQFN (9x9 mm) package. It integrates a 10-bit ADC with up to 16 channels, a 16-bit parallel master port, two I²S/SPG-02 modules, and a USB 2.0 On-The-Go controller with dedicated DMA, making it a connectivity-centric general-purpose MCU. A 32-bit microcontroller (MCU) is a microprocessor core with 32-bit-wide data paths, registers, and ALU, providing significantly higher throughput than 8- or 16-bit architectures for embedded workloads such as protocol stacks, graphics, and DSP-style filtering. PIC32MX MCUs use the MIPS32 M4K core from MIPS Technologies with hardware multiply/divide and a 5-stage pipeline, running at up to 80 MHz (80 MIPS). Within the hierarchy, PIC32MX sits under Microchip's PIC32 family -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor. They are typically paired with external peripherals such as Ethernet PHYs, USB connectors, and analog front-ends. Key features of the PIC32MX664F128H include: 128 KB Flash program memory (with ECC option on higher-density variants), 32 KB SRAM, five 16-bit timers/counters, a 16-channel 10-bit ADC at 1 Msps, two comparators, two UARTs, two SPI buses, and two I²C buses. The integrated 10/100 Mbps Ethernet MAC and USB OTG (full-speed + hi-speed PHY interface) make it suitable for connected embedded nodes. The architecture separates peripheral pin select (PPS) from physical I/O, giving 51 digital I/O lines flexible remapping across most digital peripherals. The DMA controller has 8 channels supporting data movement between peripherals and memory without CPU intervention, enabling efficient USB and ADC pipelines. Typical applications include industrial automation with Modbus/TCP, USB peripherals (HID, CDC, mass storage), Ethernet-connected sensors, home gateways, and audio processing with I²S codecs. The wide peripheral mix and integrated MAC reduce BOM cost vs. external ENC28J60 + 8-bit MCU designs. For PCB layout, place the 64-pin VQFN exposed pad soldered to a continuous ground plane for thermal dissipation and low-noise ADC performance. Decouple VDD with a 10 µF bulk + 0.1 µF ceramic per pin pair, and keep the 80 MHz crystal traces short and guarded. Use MPLAB Harmony or legacy MLA stacks for USB and TCP/IP firmware. This page combines distributor pricing, drop-in alternatives, and engineering notes drawn from the Microchip datasheet family, information not aggregated on any single distributor page.

USD $5,71 En stock

PIC32MX664F128HT-I/PT

PIC32MX664F128HT-I/PT - 32-bit MCU 80MHz 128KB Flash USB+ETH | Microchip

The Microchip Technology PIC32MX664F128HT-I/PT is a 32-bit MIPS32 M4K PIC microcontroller with an 80 MHz core, 128 KB Flash, and 32 KB SRAM, integrated USB 2.0 full-speed and 10/100 Ethernet MAC, housed in a 64-pin TQFP (PT) 10x10x1 mm package. The device delivers 1.56 DMIPS/MHz performance and integrates the PIC32MX5/6/7 series peripheral set including 4-channel DMA, multiple UART/SPI/I2C, and a 16-bit ADC. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program Flash, non-volatile data storage, RAM, and peripherals such as ADC, timers, and communication interfaces into one package. The PIC32MX6 family is Microchip's mid-range 32-bit MCU line, sitting between the PIC32MX1/2 entry-level parts and the PIC32MZ high-performance series, optimized for embedded connectivity applications. Key features of the PIC32MX664F128HT-I/PT include 128 KB (128K x 8) Flash with self-programmable Flash, 32 KB SRAM, integrated full-speed USB 2.0 device/host/OTG, integrated 10/100 Mbit Ethernet MAC, 53 usable I/O lines, a 16-channel 16-bit ADC at 500 ksps, two I2C, two SPI, two UART, four 16-bit timers, a real-time clock, and 4-channel DMA. The device supports industrial temperature range of -40C to +85C. Architecturally, the PIC32MX664F128HT-I/PT uses the MIPS32 M4K core with 5-stage pipeline, MMU-less flat memory map, and hardware multiply/divide. The peripheral set is interconnected via a peripheral bus matrix allowing simultaneous DMA and CPU access for high-throughput applications. Typical applications include industrial Ethernet nodes, USB-based data loggers, embedded web servers, home automation gateways, and POS terminals. The combination of USB, Ethernet, and 16-bit ADC makes it a strong fit for connected sensing and protocol conversion designs. When designing, allocate adequate decoupling near VDD/AVDD pins, follow Microchip's TQFP-64 land pattern, and use the MPLAB Harmony framework for peripheral drivers and TCP/IP stack.

USD $4,36 En stock

PIC32MX664F128L-I/BG

PIC32MX664F128L-I/BG - 80MHz 32-bit MCU 128KB Flash USB Ethernet | Microchip

The Microchip Technology PIC32MX664F128L-I/BG is a 32-bit MIPS M4K microcontroller running at 80 MHz with 128 KB of Flash program memory and 32 KB of SRAM, housed in a 121-ball TFBGA (10x10 mm) package. It integrates a 10/100 Mbit Ethernet MAC, USB 2.0 full-speed On-The-Go (OTG) controller, four DMA channels, and a rich set of connectivity-oriented peripherals (UART, SPI, I2C, PMP, ADC). The -I/BG suffix indicates an industrial temperature range (-40C to +85C) and the 121-pin TFBGA package. A PIC32MX microcontroller is a 32-bit MIPS-based MCU family from Microchip that combines the deterministic real-time behavior of the PIC heritage with a high-performance MIPS32 M4K core, scalar pipeline, and 32-bit ALU. The PIC32MX5/6/7 series in particular adds integrated 10/100 Ethernet MAC, USB OTG, and CAN peripherals, positioning the family between traditional 16-bit MCUs and higher-cost ARM Cortex-M3 devices for connected embedded designs. Key differentiating features of the PIC32MX664F128L-I/BG include 128 KB Flash and 32 KB RAM, an integrated Ethernet MAC that connects to an external PHY via RMII, USB OTG with integrated transceiver, four-channel DMA for offloading data movement from the core, a 10-bit 1 MSPS analog-to-digital converter, and Microchip's MPLAB Harmony framework support. Industrial-grade temperature rating and 53 usable I/O pins provide flexibility for mixed-signal embedded systems. Architecturally, the M4K core executes most instructions in a single cycle and supports a shadow register set for fast interrupt response, making it well-suited to RTOS-based and bare-metal real-time applications. The peripheral set is connected through a multi-layer bus matrix, allowing simultaneous DMA-driven Ethernet, USB, and ADC streams without CPU stall. Typical applications include industrial control with Ethernet connectivity, embedded web servers, USB device/host peripherals, low-cost Ethernet-enabled sensor nodes, and CAN-to-Ethernet bridges. The integrated Ethernet MAC plus USB OTG combination is rare at this price tier and is the primary reason this MCU is selected over lesser-connected alternatives. When designing with this part, ensure the PCB layout uses a 4-layer stackup to route the 121-ball TFBGA fan-out; BGA breakout vias should be 0.2 mm drill with 0.4 mm pitch. The Ethernet MAC requires an external PHY (e.g., KSZ8041 or LAN8720) and 49.9 ohm 1% termination resistors on the differential pairs. MPLAB X IDE with XC32 compiler and Harmony framework is the recommended toolchain. This page synthesizes distributor pricing, drop-in alternatives within the PIC32MX family, and practical design notes not found in the manufacturer datasheet.

USD $5,81 En stock

PIC32MX664F128L-V/BG

PIC32MX664F128L-V/BG - 80MHz 32-bit MCU 128KB Flash USB OTG | Microchip

The Microchip Technology PIC32MX664F128L-V/BG is a 32-bit MIPS M4K microcontroller running at 80 MHz with 128 KB of Flash and 32 KB of SRAM, housed in a 10 x 10 mm 121-ball TFBGA (BG) package. The -V speed designation refers to the VDD voltage range and the extended commercial temperature grade. The device integrates USB OTG full-speed, a 10-bit 1 MSPS ADC with up to 16 channels, five 16-bit timers, two I2C, two UART, and a 10/100 Ethernet MAC, which positions it for connected embedded designs in a single chip. The PIC32MX microcontroller family is built on the MIPS32 M4K core, an industry-standard 32-bit RISC architecture that delivers deterministic Dhrystone 2.1 performance up to 1.5 DMIPS per MHz. M4K MCUs are widely used in industrial, consumer, and connectivity-oriented applications where USB, CAN, or Ethernet must coexist with general-purpose digital and analog I/O. They fit into a hierarchy of microcontroller -> 32-bit MCU -> MIPS RISC MCU -> Microchip PIC32 family, and share toolchain support via MPLAB X IDE, MPLAB Harmony framework, and XC32 compiler. Key features of the PIC32MX664F128L-V/BG include 128 KB Flash (128K x 8), 32 KB SRAM, a 10-bit 1 MSPS ADC, dedicated DMA with up to 8 channels, and a USB 2.0 full-speed OTG controller. The parallel master port (PMP) supports graphics interfaces and external memory. The 121-ball TFBGA (BG) package provides extensive I/O for highly integrated designs while keeping the footprint to 10 x 10 mm. Architecture is the MIPS M4K core with 32-bit instruction and 32-bit data paths, hardware multiply/divide, single-cycle 32-bit shift, and a prefetch cache that improves Flash throughput. The peripheral bus matrix supports concurrent DMA between the ADC, USB, SPI, I2C, UART, and Ethernet MAC without CPU intervention, freeing the core for application code. Typical applications include USB peripherals, industrial control with CAN connectivity, Ethernet-enabled embedded nodes, graphical user interfaces using the PMP bus, and low-cost barcode scanners. Designers can develop firmware using the MPLAB Harmony framework, the MPLAB X IDE, and the free XC32 compiler. A key design consideration is power: at 80 MHz the core draws roughly 70 mA active and drops to single-digit mA in idle and low microamps in deep sleep. The -V extended grade operates from 2.3 V to 3.6 V, so logic-level peripherals must respect this range. The 121-ball TFBGA package requires reflow-compatible PCB land pattern design and X-ray inspection for production. This page combines distributor pricing for PIC32MX664F128L-V/BG, drop-in same-package alternatives from the PIC32MX5/6/7 family, and practical design notes that go beyond what is found in the standalone manufacturer datasheet.

USD $7,41 En stock

PIC32MX664F128L-V/PF

PIC32MX664F128L-V/PF - 80MHz 32-bit MCU 128KB Flash USB/Ethernet 100-TQFP | Microchip

The Microchip Technology PIC32MX664F128L-V/PF is a 32-bit MIPS M4K microcontroller with 80MHz CPU clock, 128KB Flash program memory, 32KB SRAM, integrated USB 2.0 OTG and 10/100 Mbit Ethernet MAC, housed in a 100-pin TQFP package (14x14mm). The device targets high-performance embedded connectivity applications requiring both networking and USB peripheral support. A microcontroller (MCU) is a single-chip computer containing a processor, memory (Flash for code, RAM for data), and programmable peripherals. The PIC32MX family uses the MIPS32 M4K core architecture, placing it in the broader taxonomy of 32-bit microcontrollers -> microcontrollers -> integrated circuits -> semiconductors. Compared with 8/16-bit MCUs, 32-bit parts deliver higher MIPS per MHz and richer peripheral integration; compared with ARM Cortex-M3 parts of the same vintage, the PIC32MX family emphasizes deterministic interrupt latency and integrated connectivity peripherals such as USB OTG and Ethernet MAC. Key features include 128KB single-cycle Flash, 32KB SRAM, USB 2.0 Full-Speed/High-Speed OTG with on-chip transceiver, 10/100 Ethernet MAC with MII/RMII interface, up to 16 ADC channels at 10-bit 1MSps, 5 16-bit timers/counters, two I²C, two SPI, two UART channels, and an integrated DMA controller with up to 8 channels. The 100-pin TQFP provides 85 general-purpose I/O pins and supports JTAG and 2-wire programming/debug interfaces. The architecture uses a 5-stage pipeline MIPS32 M4K core with hardware multiply/divide, providing up to 1.56 DMIPS/MHz. The on-chip regulator provides a single 2.3V-3.6V supply input, simplifying power-tree design versus parts requiring separate core/IO rails. Typical applications include industrial control with Ethernet connectivity, USB peripherals (CDC/HID/MSC), home automation gateways, embedded web servers, and point-of-sale terminals. The combination of integrated Ethernet and USB reduces BOM cost and PCB area versus discrete solutions requiring external PHY chips. When designing with the PIC32MX664F128L-V/PF, ensure the Vcap pin has a low-ESR 10uF ceramic capacitor and place it within 6mm of the pin to stabilize the internal 1.8V regulator. Use Microchip's MPLAB Harmony framework for peripheral configuration to avoid manual register-level timing pitfalls. This page synthesizes current distributor stock, drop-in same-package alternatives from Microchip's PIC32MX family, and practical design notes drawn from the manufacturer datasheet and reference designs, providing decision-support content not bundled in the original datasheet PDF.

USD $5,45 En stock

PIC32MX664F128L-V/PT

PIC32MX664F128L-V/PT - 32-bit 128KB Flash MCU 80MHz 100-TQFP | Microchip

The Microchip Technology PIC32MX664F128L-V/PT is a 32-bit MIPS32 M4K RISC microcontroller with 128 KB Flash and 32 KB SRAM, operating up to 80 MHz, and housed in a 100-pin TQFP package (12x12 mm). The -V suffix indicates the VCC range of 2.3 V to 3.6 V (PIC32MX family V-temp grade). A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (Flash), data memory (SRAM), and integrated peripherals such as timers, ADC, communication controllers, and GPIO. The PIC32MX family sits in the PIC32 -> 32-bit MCU -> microcontroller -> embedded processor -> semiconductor hierarchy and is widely used where higher computational performance is needed than 8-bit or 16-bit MCUs can deliver. Key features of the PIC32MX664F128L-V/PT include 128 KB Flash (128K x 8), 32 KB SRAM, an integrated 10/100 Ethernet MAC, USB OTG, CAN, DMA, a 10-bit ADC, and 83 programmable I/O lines. The device supports up to 80 MHz operation and provides ample connectivity peripherals, suitable for embedded networking and USB device/host/OTG applications. The architecture is a Harvard-style MIPS32 M4K core with 5-stage pipeline, separate instruction and data buses, and tightly-coupled peripherals. The USB OTG controller, Ethernet MAC, and CAN module are all integrated on-chip, eliminating the need for external bridge devices. The DMA engine offloads data movement from the CPU, freeing it for application tasks. Typical applications include industrial Ethernet gateways, USB-to-UART bridges, embedded web servers, industrial control with CAN connectivity, and POS terminals. The wide peripheral set and Ethernet/USB/CAN integration make it ideal for connected embedded devices requiring both real-time and networked operation. When designing with this device, ensure that the VDDCORE pin is bypassed correctly with the recommended capacitor network, and that the 80 MHz maximum frequency matches the chosen crystal and PLL configuration. Migrating between PIC32MX5/6/7 family parts is straightforward because they share the same peripheral library, MPLAB Harmony framework, and pin-compatible packages. This page synthesizes distributor pricing, drop-in same-package alternatives drawn from the PIC32MX family, and practical design notes not found in the manufacturer datasheet.

USD $4,67 En stock

PIC32MX664F128LT-I/BG

PIC32MX664F128LT-I/BG - 80MHz 128KB Flash MCU with USB/Ethernet

The Microchip Technology PIC32MX664F128LT-I/BG is a 32-bit MIPS MCU from the PIC32MX5/6/7 family, integrating 128 KB Flash and 32 KB SRAM with a MIPS32 M4K processor core running up to 80 MHz. The device integrates a 10/100 Mbit Ethernet MAC, USB Full-Speed (USB 2.0 FS) controller, 4-channel DMA, and a rich peripheral set in a 121-ball TFBGA (10x10x1.2 mm) surface-mount package. The part is qualified to Microchip's industrial temperature range (-40C to +85C). A 32-bit microcontroller is a single-chip computer that integrates a CPU core, program Flash, data SRAM, and a peripheral set on one die. The PIC32 family uses the MIPS32 M4K core, which executes the MIPS instruction set with single-cycle multiply and hardware debug support. Compared with 8-bit and 16-bit MCUs, 32-bit devices offer higher code density, faster arithmetic, and larger address spaces - making them suitable for embedded connectivity stacks such as TCP/IP and USB. The PIC32MX664 specifically targets connected applications by integrating Ethernet and USB peripherals alongside general-purpose I/O. Key features include 53 general-purpose I/O pins organized across multiple ports, five 16-bit timers/counters, two I2C and two SPI/I2S interfaces, two comparators, a 16-channel 10-bit ADC, and a 4-channel DMA engine that offloads memory-to-peripheral transfers. The internal 8 MHz and 32 kHz oscillators reduce BOM cost by eliminating external crystals in non-precision applications. The part supports in-circuit serial programming (ICSP) and JTAG debugging through the same pins. Typical applications include industrial Ethernet nodes, USB peripherals and embedded hosts, graphical user interfaces with integrated TFT drivers, automotive infotainment subsystems, point-of-sale terminals, and home-automation gateways. The integrated Ethernet MAC with MII/RMII interfaces allows direct connection to a PHY without an external controller, while the USB Full-Speed controller can operate in either device or host mode with on-chip transceivers. When designing with this device, ensure your PCB layout follows Microchip's TFBGA routing guidelines - the 0.8 mm pitch requires laser-via or microvia fanout for production-grade reliability. Decoupling capacitors must be placed as close as possible to every VDD/VSS pair, and the analog supply (AVDD) requires an additional LC filter. Developers typically use the MPLAB Harmony framework or MPLAB XC32 compiler for firmware development, with the PICkit or ICD debugger for in-circuit debug. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical PCB layout notes not collected on any single distributor page.

USD $5,32 En stock

PIC32MX664F128LT-I/PT

PIC32MX664F128LT-I/PT - 80MHz 32-bit MCU 128KB Flash USB Ethernet | Microchip

The Microchip Technology PIC32MX664F128LT-I/PT is a 32-bit MIPS M4K microcontroller delivering 80 MHz CPU performance with 128 KB Flash and 32 KB SRAM, housed in a 100-pin TQFP package (12x12x1 mm). It integrates USB 2.0 Full-Speed OTG, 10/100 Ethernet MAC, a 10-bit 1 Msps ADC, four DMA channels, and 83 general-purpose I/O lines, making it one of the most connectivity-rich members of the PIC32MX5xx/6xx/7xx family. A 32-bit MCU is a microprocessor core that processes 32-bit data words in a single instruction, providing roughly 4x the throughput of an 8-bit or 16-bit MCU at the same clock rate. PIC32MX devices sit in the middle of Microchip's 32-bit portfolio - above the SAM D20 Cortex-M0+ entry family in performance and below the SAM E70/SAMS70 Cortex-M7 in compute. They target connected embedded applications where Ethernet, USB, or CAN connectivity is required alongside real-time control and low BOM cost. The PIC32MX664F128LT-I/PT is built on a 5-stage pipelined MIPS32 M4K core with single-cycle hardware multiply and hardware divide. It features a 16-channel 10-bit ADC with up to 16 Msps total throughput across the channels, four dedicated DMA channels that offload data movement from the CPU, and a 16-bit Parallel Master Port for external bus expansion. The 'L' suffix denotes the 100-pin TQFP package; 'I' denotes the industrial -40C to +85C temperature range; 'T' denotes tape-and-reel packaging. Typical applications include industrial Ethernet gateways, USB device and host controllers, barcode scanners, point-of-sale terminals, building automation, and embedded web servers. The combination of full-speed USB OTG and Ethernet MAC in a single 80 MHz MCU is the key differentiator against cost-down PIC32MX1xx/2xx variants and against Microchip's own Cortex-M0+ based SAM D20/D21. When designing with this device, allocate sufficient decoupling on the 2.5V internal regulator pin (pin 56/100) - Microchip recommends a 10 uF tantalum or ceramic plus a 0.1 uF bypass on VCAP. The Ethernet MAC requires an external PHY and magnetics; the USB OTG transceiver requires external 15 k pull-downs on D+/D-. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the standalone manufacturer datasheet.

USD $6,42 En stock

PIC32MX664F128LT-V/BG

PIC32MX664F128LT-V/BG - 32-bit 80MHz MCU 128KB Flash USB OTG | Microchip

The Microchip PIC32MX664F128LT-V/BG is a 32-bit MIPS32 M4K PIC microcontroller IC running at 80 MHz, integrating 128 KB of Flash and 32 KB of SRAM in a 121-pin TFBGA (10x10 mm) package. The part is qualified for the -40C to +105C extended-industrial operating range and operates from a 2.3 V to 3.6 V supply, making it a member of the PIC32MX5/6/7 connectivity family with integrated 10/100 Ethernet MAC, USB OTG, 10-bit ADC, and DMA. A PIC32MX microcontroller belongs to the 32-bit MCU family within the broader category of microcontrollers -> embedded processors -> semiconductors. The PIC32MX5/6/7 series combines a high-performance MIPS32 M4K core with industry-leading connectivity peripherals (Ethernet, USB OTG, CAN) that allow embedded designs to add wired networking and USB device/host/OTG functionality without an external PHY companion. The M4K core executes most instructions in a single cycle and supports the MIPS16e code-compression ISA to maximise code density from the on-chip Flash. Key specifications for this part include 128 KB Flash program memory organised as 128K x 8, 32 KB SRAM, 80 MHz maximum CPU clock, an integrated 10-bit ADC with up to 16 channels and 1 Msps conversion rate, a 10/100 Mbps Ethernet MAC, USB 2.0 OTG controller with on-chip transceiver, up to 83 programmable I/O pins, and 5 timer/counters. The 121-TFBGA (10x10 mm) package is suited to compact, high-density layouts but requires careful PCB design for the 0.8 mm ball pitch. Architecturally, the PIC32MX664F128L combines a Harvard-style bus with a unified 32-bit data path, DMA controller for peripheral transfers, and a peripheral pin-select (PPS) engine that remaps digital peripherals to a wide choice of I/O pins, easing board layout. The USB OTG controller includes an integrated physical-layer transceiver, eliminating the need for an external PHY and reducing BOM cost for USB device, host and On-The-Go designs. Typical applications include industrial Ethernet nodes, USB human-interface devices, building-automation controllers, embedded web servers, and consumer audio accessories. The combination of Ethernet and USB OTG makes this part especially attractive for gateways that bridge USB peripherals onto an IP network. Designers should leverage the MPLAB Harmony software framework and the PIC32MX USB and Ethernet libraries to accelerate firmware development, and verify PCB escape routing for the 0.8 mm BGA balls with manufacturer-recommended design rules.

USD $6,10 En stock

PIC32MX664F128LT-V/PT

PIC32MX664F128LT-V/PT - 80MHz 128KB Flash USB MCU | Microchip

The Microchip PIC32MX664F128LT-V/PT is a 32-bit MIPS M4K microcontroller running at 80 MHz with 128 KB Flash and 32 KB SRAM, integrated full-speed USB OTG, 10-bit 1 Msps ADC, and 10/100 Ethernet MAC in a 100-pin TQFP (PT) 12x12 mm package. The part suffix –V denotes the extended -40C to +105C temperature range, while the T in the part number indicates tape-and-reel packaging. A 32-bit microcontroller (MCU) is a single-chip computer core based on a 32-bit data path, registers, and address space, integrating CPU, memory, peripherals and A/D - converters on one die. The PIC32MX series uses the MIPS M4K core, a Harvard-architecture processor widely deployed in embedded connectivity applications. Within Microchip's MCU taxonomy this MCU belongs to: 32-bit MCU -> MIPS32 -> PIC32 -> PIC32MX6xx family -> USB/Ethernet connectivity class. Key features include 128 KB Flash program memory organized as 128K x 8, 32 KB SRAM, USB OTG full-speed (12 Mbps) with on-chip transceiver, 10/100 Mbps Ethernet MAC, sixteen 10-bit ADC channels with 1 Msps conversion rate, five 16-bit timers plus five input-capture and five output-compare modules, two I2C and two SPI/I2S ports, and two UART modules. The device operates from 2.3V to 3.6V with 5V-tolerant digital I/O and supports MPLAB Harmony, MPLAB X IDE, and XC32 toolchains. Typical applications include USB peripherals and HID devices, Ethernet-connected embedded controllers, industrial automation nodes with USB device/host capability, point-of-sale terminals, and consumer audio/visual docks. Design considerations should include the mandatory 12 MHz primary oscillator for USB operation, layout separation of analog and digital grounds, and decoupling of the 3.3V rail close to all VDD/VSS pairs. This page synthesizes distributor pricing, drop-in same-package alternatives, and application notes not found in the standalone datasheet.

USD $5,80 En stock

PIC32MX675F256H-80V/MR

PIC32MX675F256H-80V/MR - 80MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC32MX675F256H-80V/MR is a 32-bit MIPS M4K microcontroller running at 80MHz with 256KB of Flash and 64KB of SRAM, housed in a 64-pin VQFN (9x9 mm) package. It integrates USB 2.0 On-The-Go with a dedicated DMA path, a 10/100 Ethernet MAC with MII/RMII, and a high-performance peripheral set targeting connected applications. The 'V' suffix denotes the -40C to +105C industrial temperature grade. A PIC32MX microcontroller is a 32-bit MIPS-based MCU from Microchip designed to bridge the gap between traditional 8/16-bit PIC controllers and high-end Cortex-M devices. The PIC32 family uses a 5-stage Harvard pipeline and the MIPS16e instruction set, allowing up to 40% smaller code size for compact code. Positioned in the hierarchy MCU -> 32-bit MCU -> MIPS M4K core -> connected MCU, the PIC32MX5/6/7 series specifically targets embedded connectivity. Key features include 80MHz core speed (105 DMIPS), 256KB Flash, 64KB RAM, USB-OTG with on-chip PHY, 10/100 Ethernet MAC, 53 general-purpose I/O lines, 4 dedicated DMA channels, two I2C, two SPI, five UART, two CAN, and a 16-channel 10-bit ADC. The device supports 2.3V to 3.6V single-supply operation, drawing 73mA/MIPS at full speed. The VQFN-64 9x9 package exposes the thermal pad for improved thermal performance. The PIC32MX675 uses the MIPS M4K core with hardware multiply/divide, shadow register sets, and a deterministic interrupt controller. Code density is enhanced by MIPS16e compressed instructions. The on-chip USB-OTG PHY and dedicated DMA path eliminate the need for an external PHY and reduce CPU load for full-speed and high-speed USB stacks. Ethernet MAC, USB, and DMA work together, with IPv4 checksum offload to enable robust TCP/IP stacks on a single chip. Typical applications include industrial Ethernet nodes, USB peripherals and embedded hosts, building automation controllers, point-of-sale terminals, and connected medical devices. The combination of USB-OTG, Ethernet, CAN, and ample GPIO is well suited to factory automation, bridging sensors and HMIs to Ethernet/USB networks. When designing with this device, ensure the 64-VQFN thermal pad is soldered to a sufficiently large copper pour for heat dissipation, and route the USB DP/DN lines as a 90 ohm differential pair per USB specifications. MPLAB Harmony provides integrated middleware for TCP/IP, USB, and graphics, reducing development time. This page combines distributor pricing, drop-in alternatives, and practical design notes that go beyond the manufacturer datasheet summary.

USD $4,62 En stock

PIC32MX675F256H-80V/PT

PIC32MX675F256H-80V/PT - 80MHz 32-bit MCU USB-OTG Ethernet 256KB | Microchip

The Microchip Technology PIC32MX675F256H-80V/PT is a 32-bit MIPS M4K microcontroller running at 80 MHz (105 DMIPS) with 256 KB of Flash and 64 KB of SRAM, housed in a 64-pin TQFP (PT) 10x10 mm package with 0.5 mm pitch. The PIC32MX5/6/7 family integrates a USB 2.0 On-The-Go peripheral with on-chip PHY, a 10/100 Ethernet MAC supporting MII/RMII, and a 5-stage pipelined Harvard core with MIPS16e code compression. A 32-bit MCU (microcontroller unit) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (SRAM), and peripherals. PIC32MX sits in Microchip's mid-range 32-bit family (lineage: PIC32MX -> PIC32 -> 32-bit MCU -> microcontroller -> embedded processor). It targets connectivity-rich embedded designs, sitting above 8-bit PIC16/PIC18 and below higher-end Cortex-M and Cortex-A parts, balancing performance, peripherals, and cost. Key features include 51 digital I/O lines, a 16-channel 10-bit ADC at 1 Msps, four 16-bit timer/counters, two I2C, two SPI, two UART, and four dedicated DMA channels for USB OTG. The supply range is 2.3 V to 3.6 V (operating core 2.5 V to 3.6 V), industrial -40 C to +105 C operating temperature (V suffix), and JTAG/ICSP debug with trace. The 80V suffix denotes the 80 MHz speed grade and the V = -40 C to +105 C industrial extended temperature window. Architecturally, the PIC32MX uses the MIPS M4K core, which executes most MIPS32 instructions in a single cycle and provides hardware multiply/divide and DSP extensions. Harvard architecture separates instruction and data paths, enabling simultaneous fetch and memory access. The dedicated DMA engine offloads USB OTG and memory-to-memory transfers from the CPU, freeing MIPS for application code. Typical applications include industrial Ethernet gateways, USB-OTG device/host controllers, building automation nodes, and embedded web servers. The combination of integrated Ethernet MAC, USB OTG with PHY, and ample RAM makes this part well suited for connected appliances, point-of-sale terminals, and remote sensor concentrators. The V temperature grade supports outdoor and factory-floor deployments. When designing with this MCU, allocate decoupling capacitors near each VDD/VSS pair, route the 50 MHz Ethernet reference clock with controlled impedance, and reserve area for the 32 kHz secondary oscillator if RTC operation is required. Use MPLAB Harmony to configure the USB OTG and Ethernet stacks; without it the firmware effort roughly doubles. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet.

USD $6,58 En stock

PIC32MX675F256HT-80I/MR

PIC32MX675F256HT-80I/MR - 80MHz 32-bit MCU w/ Ethernet | Microchip

The Microchip Technology PIC32MX675F256HT-80I/MR is a 32-bit MIPS32 M4K microcontroller integrating 256 KB of Flash program memory and 64 KB of SRAM, clocked at up to 80 MHz, and packaged in a 64-pin VQFN (9x9 mm) with an exposed thermal pad for enhanced heat dissipation. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a 32-bit CPU core, volatile and non-volatile memory, and a rich set of on-chip peripherals such as timers, communication controllers, ADCs, and DMA engines. Within the broader taxonomy, MCUs sit under microprocessors (MPU -> MCU -> 32-bit MCU) and are part of the embedded computing category. The PIC32MX family specifically targets connectivity-rich embedded applications, including industrial control, consumer devices, and networked embedded products. This particular PIC32MX675F256HT-80I/MR sits at the high end of the PIC32MX5/6/7 series, distinguished by its on-chip 10/100 Mbit Ethernet MAC and full-speed USB 2.0 controller. Key features of the PIC32MX675F256HT-80I/MR include 256 KB Flash organized as 256K x 8, 64 KB RAM, eight DMA channels for low-CPU-overhead data movement, an integrated 10/100 Ethernet MAC with the necessary RMII/MII interface, USB 2.0 full-speed OTG/Friendly host-or-device controller, multiple UART/SPI/I2C peripherals, a 10-bit ADC of 16 channels, and a parallel master port for external bus expansion. The part operates from a 2.3 V to 3.6 V supply and is rated for the industrial -40C to +85C temperature range. Architecturally, the PIC32MX675F256HT-80I/MR uses the MIPS32 M4K core with a 5-stage pipeline, hardware multiply/divide, and a single-cycle 32-bit ALU. Microchip's MPLAB Harmony framework supports the device with peripheral libraries, USB and TCP/IP stacks, and a graphical configuration tool. The Ethernet MAC connects directly to an external PHY (such as the Microchip KSZ8041) via RMII, eliminating the need for an external MAC. Eight DMA channels can service the ADC, SPI, UART, USB, and Ethernet peripherals in parallel, freeing the CPU for application logic. Typical applications include industrial Ethernet gateways, networked sensor nodes, USB peripherals, building automation controllers, and embedded web servers. The combination of Ethernet, USB, 256 KB Flash, and 64 KB RAM is well matched to small RTOS-based designs running TCP/IP stacks. When designing with this MCU, place the 64-pin VQFN exposed pad on a sufficiently large copper pour for thermal relief, since industrial Ethernet applications often run near 80 MHz. The Ethernet MAC requires an external 50 MHz reference clock input; ensure your PHY or oscillator circuit meets the RMII timing budget. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet alone.

USD $7,32 En stock

PIC32MX675F256HT-80V/MR

PIC32MX675F256HT-80V/MR - 80MHz 32-bit MCU 256KB Flash USB Ethernet

The Microchip Technology PIC32MX675F256HT-80V/MR is a 32-bit MIPS32 M4K microcontroller running up to 80 MHz, integrating 256 KB Flash and 64 KB SRAM in a 64-pin VQFN (9x9 mm) package with exposed pad. It provides integrated USB-OTG and 10/100 Ethernet MAC connectivity, 53 general-purpose I/O, DMA, and a 16-channel 10-bit ADC. A microcontroller (MCU) is a single-chip computer that combines a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a rich set of peripherals. The PIC32MX5/6/7 family targets embedded connectivity-based applications, sitting in the PIC32 hierarchy between simpler PIC32MX1/2/3/4 devices and higher-pin-count PIC32MX7 series. It uses the MIPS32 M4K RISC core, licensed architecture now maintained by MIPS, optimized for deterministic real-time control with predictable interrupt latency. Key features include 256 KB on-chip Flash, 64 KB SRAM, DMA controller, four 16-bit timers, two I2C, two SPI, two UART, USB-OTG full-speed, 10/100 Mbps Ethernet MAC, 10-bit 1 MspsA conversion ADC with 16 channels, and five 16-bit compare/PWM modules. The "V" temperature grade supports -40C to +105C, while "80" denotes the 80 MHz maximum operating frequency. Typical applications include industrial Ethernet gateways, USB peripherals, embedded web servers, HMI controllers, point-of-sale terminals, and connectivity-equipped sensor nodes. Engineers choose this part when a single chip must host both TCP/IP networking and USB device/host functions without external PHY complexity. When designing, ensure the exposed thermal pad is soldered to a sufficient copper pour for thermal dissipation. Verify the supply voltage stays within 2.3V-3.6V during transient load steps. The MPLAB Harmony framework provides TCP/IP, USB, and graphics stacks to accelerate development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on DigiKey or Mouser product pages. All specifications reflect the manufacturer datasheet current at the time of verification.

USD $6,30 En stock

PIC32MX675F256HT-80V/PT

PIC32MX675F256HT-80V/PT - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip PIC32MX675F256HT-80V/PT is a 32-bit MIPS M4K microcontroller running at up to 80 MHz, integrating 256 KB Flash and 64 KB SRAM with USB-OTG, 10/100 Ethernet MAC, and a 10-bit ADC in a 64-pin TQFP (10x10 mm) package. The 'V' speed grade and -40C to +105C industrial operating range make it suitable for embedded connectivity designs that must operate across commercial and industrial temperature extremes. Per the Microchip product page, the part is supported by MPLAB Harmony integrated software framework. A 32-bit microcontroller (MCU) is a programmable processor built around a 32-bit data path, typically with on-chip Flash program memory, SRAM, peripherals, and interrupt controller. The PIC32MX series sits in the hierarchy: 32-bit MCU -> embedded processor -> MIPS M4K core -> Microchip PIC32 portfolio. Compared with 8-bit/16-bit MCUs, 32-bit parts provide higher throughput, larger address spaces, and richer peripherals for connected embedded designs. Key features include 256 KB Flash, 64 KB RAM, USB-OTG (host/device/OTG), 10/100 Ethernet MAC with MII/RMII interface, two I2C, two SPI, two UART, five 16-bit timers, five input-capture and five output-compare modules, a 10-bit 1 Msps ADC with up to 16 channels, and a parallel master port (PMP). The 64-pin TQFP footprint exposes 53 general-purpose I/O pins, leaving several pins dedicated to oscillator, JTAG, and analog functions. The M4K core executes most instructions in one cycle, providing 1.56 DMIPS/MHz and integer DSP extensions. The Ethernet MAC integrates an MII/RMII interface and the USB-OTG controller adds full-speed and low-speed USB with on-chip transceiver, removing the need for an external PHY for USB. DMA channels offload data movement between peripherals and memory, freeing the CPU for application code. Typical applications include industrial Ethernet nodes, USB-OTG peripherals (HID, CDC, mass storage, audio), Ethernet-enabled PLCs, HVAC and building automation controllers, and graphical user interfaces using PMP to drive LCDs. Its combination of Ethernet, USB, and 80 MHz MIPS core suits connected industrial and consumer designs. When designing with the PIC32MX675F256HT-80V/PT, ensure the 2.3-3.6V supply is decoupled with 100 nF + bulk ceramic placed near the VDD/VSS pairs. Configure the JTAG/ICSP pins (TMS, TCK, TDI, TDO) carefully so production programming is not blocked. Use the Ethernet MAC with an external PHY qualified for the target EMI environment. This page synthesizes distributor pricing, drop-in alternatives, and side-by-side parametric guidance not found on the manufacturer product page alone, allowing engineers to evaluate the PIC32MX675F256HT-80V/PT against alternatives in one view.

USD $3,62 En stock

PIC32MX675F256L-80I/BG

PIC32MX675F256L-80I/BG - 32-bit MCU 80 MHz 256 KB Flash USB ENET | Microchip

The Microchip PIC32MX675F256L-80I/BG is a 32-bit MIPS32 M4K microcontroller running at 80 MHz with 256 KB of Flash and 64 KB of SRAM, integrating a 10/100 Mbit Ethernet MAC, USB 2.0 full-speed device/host/OTG, two I2C, two UART, two SPI and a parallel master port. It is housed in a 121-ball TFBGA (10x10 mm) package and operates across -40C to +85C industrial temperature range. A 32-bit microcontroller (MCU) is a single-chip computer that integrates a high-performance CPU core, Flash program memory, SRAM data memory, and a rich peripheral set. Microchip's PIC32 family is positioned between traditional 8/16-bit microcontrollers and high-end application processors, targeting industrial control, embedded connectivity, and USB-centric designs. The MIPS32 M4K core inside PIC32MX devices delivers 1.5 DMIPS/MHz with single-cycle multiply and hardware multiply-accumulate, enabling efficient DSP routines and protocol stack execution. The PIC32MX675F256L-80I/BG features 256 KB Flash and 64 KB RAM, 8-channel DMA, 16-bit timers, 10-bit ADC, PMP (parallel master port), and integrated Ethernet MAC that connects to a 100 Mbit PHY via RMII/MII. The 121-TFBGA package provides 84 dedicated I/O pins for board-level integration. USB 2.0 full-speed On-The-Go enables dual-role USB peripherals, eliminating the need for external controllers. The device supports 2.3V to 3.6V core VDD and operates from -40C to +85C industrial range. The architecture uses a Harvard bus with separate 32-bit instruction and 32-bit data paths to the Flash and SRAM, plus a tightly coupled prefetch cache that masks Flash latency. The 10/100 Ethernet MAC includes an MII/RMII interface for external PHY connection, supporting both 10 Mbit and 100 Mbit rates. Dedicated DMA engines offload data movement from the CPU, freeing MIPS for application code. Typical applications include industrial Ethernet nodes with Modbus TCP, USB peripherals and HID devices, embedded web servers, gateway routers bridging USB to Ethernet, and graphical connectivity with PMP interface. The integrated Ethernet and USB make it a single-chip solution for connected IoT edges. When designing with this part, reserve 1-2 mA per VDD rail and use a four-layer PCB with dedicated ground plane to keep Ethernet RMII signals clean. The 121-TFBGA package requires reflow soldering with proper thermal relief to the ground pad for reliable power dissipation. The Ethernet MAC requires an external MII/RMII PHY such as the LAN8720A or DP83848 for physical layer termination. This page synthesizes distributor pricing, drop-in alternatives, and practical engineering notes not found in the manufacturer datasheet.

USD $6,20 En stock

PIC32MX675F256L-80I/PF

PIC32MX675F256L-80I/PF - 80MHz 32-bit MCU 256KB Flash | Microchip

The Microchip Technology PIC32MX675F256L-80I/PF is a 32-bit MIPS32 M4K PIC microcontroller integrating 256 KB of Flash program memory and 64 KB of SRAM, housed in a 100-pin TQFP (14x14 mm, PF suffix) package and running at up to 80 MHz across the industrial -40C to +85C temperature range. A 32-bit microcontroller (MCU) is an integrated circuit that combines a 32-bit CPU core, program and data memory, and a rich set of programmable peripherals on a single silicon die. PIC32MX MCUs sit in the broader taxonomy of microcontrollers -> 32-bit microcontrollers -> MIPS-based microcontrollers -> embedded controllers -> semiconductor ICs, designed for applications that need more computational headroom than 8-bit or 16-bit parts but lower power and simpler toolchains than Cortex-M devices. Key features include an integrated 10/100 Mbit Ethernet MAC, USB 2.0 full-speed On-The-Go controller with dedicated DMA, eight DMA channels for low-CPU-overhead data movement, a 16-channel 10-bit ADC, two I2C, two SPI, and five UART/I2C modules, plus five 16-bit timers/capture/compare/PWM modules. The M4K core supports the MIPS DSP ASE, providing single-cycle MAC and saturating arithmetic for signal-processing workloads. The PIC32MX6xx family is fabricated on a CMOS process that delivers the deterministic interrupt latency and 5-stage pipeline performance typical of the MIPS architecture, while the integrated Ethernet MAC and USB OTG reduce the need for external interface chips. Up to 83 general-purpose I/O lines and peripheral pin select (PPS) give layout flexibility, and MPLAB Harmony provides a unified firmware framework for these peripherals. Typical applications include industrial Ethernet nodes (Modbus TCP, EtherNet/IP gateways), USB device and embedded-host products, networked sensors, HMI panels with TFT displays, audio processing with the DSP ASE, and bridging between Ethernet and USB in factory automation. The combination of Ethernet + USB + ample RAM also suits connected data loggers and protocol converters. When designing with this device, plan the pin-out using the Peripheral Pin Select feature early; mismatched PPS mappings are the most common bring-up issue. For Ethernet, add the required 50 MHz reference oscillator circuit, bias resistor network, and pulse transformer specified in the PIC32MX5/6/7 family reference manual. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.

USD $6,55 En stock

PIC32MX675F256L-80V/BG

PIC32MX675F256L-80V/BG - 80MHz 256KB Flash MCU | Microchip

The Microchip Technology PIC32MX675F256L-80V/BG is a 32-bit MIPS MCU from the PIC32MX5/6/7 family, integrating 256KB Flash and 64KB SRAM in a 121-ball TFBGA (10x10mm, 0.8mm pitch) package. It runs at 80MHz core clock with the MIPS32 M4K core, providing 1.56 DMIPS/MHz performance. The device integrates 10/100 Mbps Ethernet MAC, USB 2.0 OTG full-speed, two I2C, two UART, two SPI, 16-channel 10-bit ADC, five 16-bit timers, and a parallel master port for external bus expansion. A microcontroller (MCU) is a single-chip computer containing a CPU core, program memory (Flash), data memory (SRAM), and integrated peripherals. The PIC32MX family specifically targets embedded connectivity applications, sitting within the broader taxonomy: 32-bit MCU -> embedded controller -> semiconductor. MIPS-based MCUs offer deterministic performance, competitive code density, and strong compiler support through GCC and MPLAB XC32. Microchip's MPLAB Harmony framework provides royalty-free middleware (TCP/IP stacks, USB, graphics, file systems) to accelerate development on this part. The integrated Ethernet MAC and USB-OTG controller distinguish this part from lower-end PIC32 variants, eliminating the need for external PHY-less MAC expanders in many designs. The 83 GPIO pins support up to five 16-bit timers with capture/compare/PWM, plus an input capture module and output compare module for waveform synthesis. The 16-channel 1 Msps 10-bit ADC enables direct sensor interfacing without an external ADC. A 4-channel DMA controller offloads memory transfers, freeing the CPU for application logic. The 121-ball TFBGA package provides a compact footprint while exposing the parallel master port (PMP) for external bus interfacing to memories or graphics controllers. With industrial temperature grade and 3.3V single-supply operation, the part suits factory automation, point-of-sale terminals, building automation controllers, and networked sensor hubs where wired connectivity is required. When designing with this part, ensure the 3.3V supply is well-decoupled with 100nF ceramic plus 10uF bulk capacitors near each VDD/VSS pair, and that the Ethernet PHY uses the RMII interface correctly. The TFBGA requires X-ray or rework station inspection for prototype rework.

USD $7,92 En stock

Productos (18688)