Microcontrôleurs

Produits (19 000+)

PIC18LF26J13-I/ML - 64KB Flash, 48MHz 8-bit MCU | Microchip
PIC18LF26J13-I/ML

PIC18LF26J13-I/ML - 64KB Flash, 48MHz 8-bit MCU | Microchip

The Microchip Technology PIC18LF26J13-I/ML is an 8-bit PIC18 XLP nanoWatt microcontroller with 64KB Flash, 4KB RAM, and a 12-bit ADC, housed in a 28-pin QFN (ML) 6x6 mm package with exposed pad. It operates at up to 48 MHz (12 MIPS) from a 2.0-3.6 V supply and is positioned for low-power, cost-sensitive embedded designs in the PIC18 J-series family. An 8-bit microcontroller (MCU) is a self-contained computing element integrating a CPU core, program memory, RAM, peripherals, and I/O on a single die. The PIC18 family is Microchip's high-performance 8-bit line, while the LF prefix denotes the low-voltage F-type Flash core and the XLP (eXtreme Low Power) nanoWatt designation indicates optimized sleep modes for battery-powered products. Within the broader taxonomy, the PIC18LF26J13 sits under: microcontroller -> 8-bit MCU -> PIC18 family -> PIC18 J-series -> low-power sub-family. Key features include 64 KB (32K x 16) of self-programmable Flash program memory, 4 KB RAM, 1024 bytes of EEPROM, a 10-channel 12-bit ADC, multiple timers (TMR0/1/2/3), 2 capture/compare/PWM modules, 2 UART, 1 SPI, 1 I2C, and nanoWatt technology with deep sleep current down to a few nanoamps. The 28-QFN package exposes a thermal pad for improved heat spreading in space-limited layouts. Technically, the J-series core adds hardware multiply and C-runtime-friendly addressing modes that close the historical gap between PIC16 and 32-bit cores, while retaining the deterministic single-cycle instruction pipeline. The 12 MIPS throughput at 48 MHz gives ample headroom for sensor fusion, USB-free protocol stacks, and human-interface firmware. Typical applications include low-power IoT sensor nodes, battery-powered medical monitors, consumer appliances, USB HID class replacements, and industrial control panels. Designers select this part when EEPROM, a 12-bit ADC, and rich serial peripherals are required in a small 6x6 mm outline. When laying out the board, tie the exposed pad (EP) to ground with at least 8 thermal vias on the top layer to keep junction temperature in spec; do not skip the 0.1 uF decoupling pair on VDD/AVDD plus a 10 uF bulk capacitor. Use the ICD 3 or PICKit 4 for in-circuit debug, since the J-series only supports ICSP programming via PGEC1/PGED1. This page synthesizes distributor pricing, drop-in same-family alternatives, and design notes that go beyond what the manufacturer datasheet alone provides.

Devis Contact
PIC18LF26J13-I/SO - 8-bit 48MHz 64KB Flash MCU | Microchip
PIC18LF26J13-I/SO

PIC18LF26J13-I/SO - 8-bit 48MHz 64KB Flash MCU | Microchip

The Microchip PIC18LF26J13-I/SO is an 8-bit PIC18 XLP nanoWatt microcontroller with 64KB (32K x 16) Flash program memory, 4KB RAM, and a 48MHz internal oscillator, packaged in a 28-pin SOIC (0.295" / 7.50mm width). The 'LF' prefix denotes the low-voltage variant supporting 2.0V to 3.6V core operation, while the 'J13' family integrates nanoWatt XLP power management, a 12-bit ADC, multiple PWM/SCCP modules, and USB-/Ethernet-ready peripherals for connected embedded designs. A PIC18 microcontroller is a member of Microchip's 8-bit PIC (Peripheral Interface Controller) family built on a Harvard RISC architecture with a modified instruction set optimized for deterministic single-cycle execution (except branches). PIC18F/LF parts sit between the baseline PIC10/12/16 line and the 16-bit dsPIC/PIC24 family, offering a richer peripheral set (12-bit ADC, CCP/SCCP, MSSP, EUSART) and larger memory while remaining programmable in nanolit. Within the PIC18 hierarchy, the LF sub-line is the low-Vdd branch designed for battery-powered XLP (eXtreme Low Power) applications, with sleep currents measured in nanoamps. Key features of the PIC18LF26J13 include 64KB Flash self-programmable via ICSP, 4KB SRAM, up to 28 I/O, 12-bit A/D converter with up to 10 channels, multiple Enhanced CCP (ECCP) and Capture/Compare/PWM (CCP) modules, two MSSP (SPI/I2C) ports, two EUSART modules with LIN support, real-time clock (RTCC) with calendar, and nanoWatt XLP technology offering <100 nA typical sleep current with RTCC and WDT active. The integrated 48MHz precision internal oscillator removes the external crystal in many cost-sensitive designs. The PIC18LF26J13 uses an enhanced Harvard core with 16-bit instructions and a hardware multiplier, executing most instructions in one cycle (~83 ns at 48 MHz FOSC). On-chip peripherals are mapped via a Peripheral Pin Select (PPS) module, allowing flexible pin remapping of digital functions. The 12-bit ADC supports up to 16 channels with automated channel scanning, while the CTMU module provides touch sensing and capacitive proximity measurement. Typical applications include battery-powered sensor nodes, USB peripherals, home appliances with LCD/keypad interfaces, industrial control panels, and low-power wireless sensor networks paired with sub-GHz transceivers. The combination of nanoWatt sleep modes and 12-bit ADC makes the part suitable for energy-harvesting and remote-monitoring designs. When designing with this device, ensure VDD decoupling is placed close to the pins and that the internal 48 MHz configured for precision (INTOSC) accuracy is acceptable for timing-critical peripherals such as EUSART. Pin-compatible PIC18F26J13 variants operate over a wider 2.0V-3.6V/4.2V-5.5V range but consume more active current. This page synthesizes distributor pricing for SOIC-28 variants, drop-in alternatives within the PIC18LF26J13 family, and practical design notes not found in the manufacturer datasheet.

Devis Contact
PIC18LF26J13-I/SP - 8-bit 48MHz 64KB Flash MCU | Microchip
PIC18LF26J13-I/SP

PIC18LF26J13-I/SP - 8-bit 48MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18LF26J13-I/SP is an 8-bit PIC18J-series microcontroller featuring a 48 MHz internal clock, 64 KB of Flash program memory, 4 KB of RAM, and an integrated 12-bit ADC, housed in a 28-pin SPDIP (SP) through-hole package. According to the Verified Web Data summary, this member of the PIC XLP 18J family targets low-power and high-performance 8-bit embedded designs that need generous program space and a rich peripheral set. What is an 8-bit microcontroller? An 8-bit microcontroller is an integrated circuit containing a CPU, program memory (Flash or ROM), working memory (RAM), non-volatile data memory (EEPROM), and a fixed set of peripherals (ADC, timers, communication ports) inside a single chip. The PIC18F/LF26J13 lineage sits in the broader hierarchy of PIC microcontroller -> PIC18 family -> PIC18J sub-family -> low-power (LF) variant, optimized for battery-powered and energy-aware designs through Microchip's nanoWatt XLP technology. Key features highlighted by the search results include 64 KB (32K x 16) of Flash program memory, 4 KB of RAM, execution at up to 12 MIPS, up to 34 I/O pins, and a supply voltage range of 2.0 V to 3.6 V for the LF variant, supporting industrial operating temperatures. Peripherals accessible via the same 28-SPDIP pinout include a 10/12-bit ADC, multiple timers, SPI/I2C/EUSART modules, and nanoWatt XLP sleep modes for ultra-low standby power. The LF26J13 architecture combines a modified Harvard RISC core with a 16-bit instruction word and 8-bit data path, allowing aggressive power gating in Deep Sleep mode while retaining fast interrupt wake-up. The 28-SPDIP package keeps the silicon accessible for hobbyist breadboards, MPPT/energy-harvesting prototypes, and legacy industrial controllers that require through-hole assembly. Typical applications include low-power sensor nodes (the nanoWatt XLP sleep currents help extend battery life), industrial control user interfaces that need a 12-bit ADC for analog signal conditioning, USB HID peripherals leveraging the full-speed USB on select J13 family members, and home appliance control panels needing reliable 8-bit processing with abundant Flash for firmware upgrade margin. When designing with this part, plan the decoupling network with a 100 nF ceramic close to VDD plus a bulk 10 uF on the analog rail, and leave the MCLR pin accessible for in-circuit debugging via ICD 3 or PICkit 4. Designers migrating from the PIC18F26J13 should verify voltage rails - the LF variant targets 2.0-3.3 V systems, while the F variant supports 2.0-3.6 V with 5 V-tolerant I/O. This page combines distributor pricing benchmarks, pin-compatible drop-in alternatives from the PIC18F/LF26J13 family, and field-validated design notes that are not duplicated in the manufacturer datasheet.

Devis Contact
PIC18LF26J13-I/SS - 64KB Flash 8-bit MCU 48MHz SSOP-28 | Microchip
PIC18LF26J13-I/SS

PIC18LF26J13-I/SS - 64KB Flash 8-bit MCU 48MHz SSOP-28 | Microchip

The Microchip Technology PIC18LF26J13-I/SS is an 8-bit RISC microcontroller from the PIC18 J-series featuring 64KB Flash program memory (32K x 16 organization) and 4KB RAM, executing at up to 48 MHz (12 MIPS) in a 28-pin SSOP package. It belongs to Microchip's PIC XLP eXtreme Low Power family, providing deeply integrated peripherals and ultra-low-power modes for battery-constrained applications while sustaining sustained computational throughput across industrial temperature grades. A PIC microcontroller is a Harvard-architecture 8-bit MCU built around a RISC instruction set, on-chip Flash program memory, RAM, EEPROM and rich peripherals including ADC, timers and serial communication blocks. Within the broader taxonomy the part sits at: microcontroller -> 8-bit MCU -> PIC18 family -> PIC18 J-series -> nanoWatt XLP variants. The LF prefix denotes the LF (Low-Voltage/Frequency) variant scaled for 2.0-2.75V wide-range supply rails typical of single-cell Li-ion or 2-AA battery systems, whereas the F variant (PIC18F26J13) shares the same silicon die but supports the wider 2.15-3.6V range. Key features include 64KB self-programmable Flash with 4KB SRAM, 10-bit and 12-bit ADC channels, dual USART, dual SPI and I2C interfaces, and 22 general-purpose digital I/O pins. nanoWatt XLP technology adds deep sleep, doze and idle modes that drop quiescent current into the sub-microamp range, enabling multi-year coin-cell lifetimes in sleep-dominant applications. The architecture combines a 16-bit instruction word with an 8-bit data path, plus a peripheral-rich core that integrates comparators, capture/compare/PWM modules, a real-time clock and a CTMU charge-time measurement unit for capacitive touch sensing. Hardware multiplier and hardware DMA-style peripheral arbitration minimise CPU overhead in mixed-signal designs. Typical applications include battery-powered sensor nodes, portable medical devices, industrial control and HMI panels, USB-to-UART bridges, capacitive touch human-machine interfaces, and home automation controllers. The dual-USART plus dual-SPI combination makes it especially attractive for multi-bus sensor aggregation. Designers targeting multi-rail power domains or systems requiring sequenced shutdown benefit from the LF-variant low-voltage threshold. When using this part, ensure VDD decoupling uses a 100 nF ceramic plus 1 uF bulk within 5 mm of the pins, and configure the CONFIG register for the correct oscillator mode (HS, XT or INTOSC) before code lock. For capacitive touch applications allocate a 10 ms scan budget and route the CTMU pins with guarded ground to suppress noise injection. This page synthesizes distributor pricing, parametric comparison tables, pin-compatible drop-in alternatives and practical design notes that extend the manufacturer datasheet context.

Devis Contact
PIC18LF26J13T-I/ML - 64KB Flash XLP 8-bit MCU 28-VQFN | Microchip
PIC18LF26J13T-I/ML

PIC18LF26J13T-I/ML - 64KB Flash XLP 8-bit MCU 28-VQFN | Microchip

The Microchip Technology PIC18LF26J13T-I/ML is a low-power 8-bit PIC microcontroller from the PIC18 XLP family, offering 64KB of Flash program memory (32K x 16) and 3.8KB of RAM, operating at up to 48MHz (12 MIPS) in a 28-pin VQFN (ML, 6x6 mm) package with exposed thermal pad. The device belongs to the PIC18 J-series, integrates an internal oscillator, and supports 22 digital I/O lines plus a 12-bit ADC, making it suitable for general-purpose embedded designs that demand low active and sleep currents. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory, volatile working RAM, and a rich set of peripherals (ADC, timers, communication interfaces, GPIO). The PIC18 family uses a modified Harvard RISC architecture with 16-bit instructions and 8-bit data, optimized for deterministic real-time response. Within the broader hierarchy, an 8-bit MCU sits below 32-bit Cortex-M devices in raw compute power but typically wins on cost, simplicity, and active-current efficiency in cost-sensitive or battery-powered designs. Key features of the PIC18LF26J13T-I/ML include 64KB Flash, 3.8KB RAM, 22 I/O pins, internal oscillator, 12-bit A/D converter, and Microchip's eXtreme Low Power (XLP) technology, which enables nanoWatt sleep modes for long battery life. The wide 2.0V-3.6V operating range simplifies direct connection to single-cell Li-ion or two-AA battery stacks without additional regulation. The 28-VQFN (ML) 6x6 mm package with exposed pad supports efficient thermal dissipation and compact PCB layouts. The PIC18 J-series core runs instructions in 4 clock cycles, achieving 12 MIPS at 48 MHz, with hardware multiplier, C compiler friendly architecture, and rich peripheral set including USB, SPI, I2C, and UART. The integrated 12-bit ADC delivers up to 16 channels for sensor acquisition, and the nanoWatt XLP power management provides multiple software-selectable sleep modes with wake-on-interrupt capability for energy harvesting applications. Typical applications include battery-powered sensor nodes, USB peripherals, industrial control panels, consumer appliances, and low-cost IoT edge devices where the combination of XLP nanoWatt sleep, USB, and ample Flash is decisive. When designing with this part, ensure proper decoupling (100 nF plus 10 uF bulk) close to the VDD pins, follow the recommended PCB layout for the exposed thermal pad, and consult Microchip's PIC18 J-series family reference manual for peripheral configuration.

Devis Contact
PIC18LF26J13T-I/SS - 8-bit 48MHz XLP MCU 64KB Flash | Microchip
PIC18LF26J13T-I/SS

PIC18LF26J13T-I/SS - 8-bit 48MHz XLP MCU 64KB Flash | Microchip

The Microchip Technology PIC18LF26J13T-I/SS is an 8-bit PIC18 XLP microcontroller with 64KB Flash, 3.8KB RAM, 12 MIPS performance, and a 12-bit ADC, housed in a 28-pin SSOP package on tape-and-reel. It is designed for low-power, high-performance embedded applications requiring a balance of code density, peripheral integration, and ultra-low power consumption. An 8-bit PIC microcontroller (MCU) is a single-chip computer built on a Harvard architecture with separate program and data buses, optimized for deterministic real-time control. Within the broader microcontroller hierarchy, the PIC18 family sits above PIC16 and PIC10/12 devices, below the PIC24/dsPIC line, and ultimately belongs to the embedded microcontroller > RISC processor > semiconductor taxonomy. The "LF" prefix denotes the wide-voltage 1.8V-3.6V variant optimized for battery-powered systems, while "J13" identifies the specific family combining enhanced peripherals with XLP nanoWatt technology. Key features include 64KB Flash program memory (32K x 16 words), 3.8KB RAM, 22 digital I/O pins, internal oscillator support, and 12 channels of 10/12-bit ADC. The 12 MIPS execution rate (at 48 MHz) provides responsive control loops, while deep sleep current in the nanoWatt range allows years of operation from a single coin cell. Multiple serial interfaces including I2C, SPI, and enhanced USART enable flexible peripheral connectivity for sensor and communication subsystems. The device combines a RISC instruction set with C-optimized architecture and a wide array of core-independent peripherals such as CCP, enhanced PWM, and configurable logic cells. This peripheral integration reduces external component count and BOM cost while offloading tasks from the CPU. Internal voltage reference and self-programming Flash further simplify system design. Typical applications include portable medical devices, IoT sensor nodes, battery-powered instrumentation, home automation controllers, and consumer electronics with USB or display interfaces. The XLP technology makes it especially attractive for energy-harvesting and remote-sensing designs where quiescent current dominates battery life. When designing with this MCU, careful decoupling near VDD pins and adherence to the trace-length guidelines in the datasheet are essential for ADC accuracy. Internal oscillator trimming may be required for time-critical protocols such as USB or CAN. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and selecting the PIC18LF26J13T-I/SS.

Devis Contact
PIC18LF26J50-I/SP - 8-Bit 48MHz USB MCU 64KB Flash | Microchip
PIC18LF26J50-I/SP

PIC18LF26J50-I/SP - 8-Bit 48MHz USB MCU 64KB Flash | Microchip

The Microchip Technology PIC18LF26J50-I/SP is an 8-bit PIC18 XLP microcontroller with integrated full-speed USB 2.0, 64KB (32K x 16) of Flash program memory, and a maximum clock speed of 48 MHz, housed in a 28-pin SPDIP (SP) through-hole package. It belongs to the PIC18 J-series family and is offered in an industrial temperature grade (-40C to +85C), with the 'LF' prefix denoting the 2.0V-3.6V low-voltage core optimized for battery- and USB-powered designs. What is a PIC18 microcontroller? A PIC18 is an 8-bit RISC microcontroller from Microchip's PIC18 family, which sits hierarchically under microcontroller -> MCU -> embedded processing unit -> semiconductor. The 'J' sub-family extends the classic PIC18 instruction set with integrated USB 2.0 full-speed peripherals, higher pin-count variants, and nanoWatt XLP power management for sleep-style low-power designs. Key features include 4KB RAM, 16 I/O pins, and an on-chip 10-bit ADC. Connectivity peripherals include I2C, SPI, UART/USART, and USB 2.0 full-speed with an internal transceiver. Brown-out detect, power-on reset, a watchdog timer, PWM, and DMA support give this device the peripheral breadth needed for connected embedded designs. A deep sleep mode further lowers quiescent current for battery-style standby operation. Technically, the device executes instructions in a single cycle (4 system clocks) thanks to the PIC18 RISC pipeline, giving roughly 16 MIPS peak throughput at 48 MHz. The 28-SPDIP package exposes two 8-bit I/O ports plus dedicated USB D+/D- lines, an external interrupt pin, and a 4 MHz-to-48 MHz internal PLL block fed from the on-board 8 MHz HFINTOSC. Configuration bits let the designer disable the internal regulator for full 2.0V-3.6V operation. Typical applications include USB HID peripherals such as custom joysticks, mice, and barcode scanners, low-power sensor nodes, USB-to-UART bridges, and embedded learning platforms. The PIC18LF26J50 is also widely used as a USB bootloader target and as a stepping stone for developers migrating from legacy PIC18F4550 designs to lower-pin-count packages. When designing with this part, pair it with a 6 MHz or 12 MHz crystal (HS-PLL mode) when USB bus accuracy is critical, or use the internal 8 MHz HFINTOSC with USB clock recovery for BOM-minimized designs. A 100nF decoupling cap on VDD/VUSB and a 4.7uF bulk capacitor on VUSB are essential for USB compliance. This page synthesizes distributor pricing, drop-in PIC18 family alternatives, and practical design notes not found in the bare manufacturer datasheet, giving engineers a faster procurement and design decision.

Devis Contact
PIC18LF26J50T-I/ML - 8-bit USB MCU 64KB Flash 28-QFN | Microchip
PIC18LF26J50T-I/ML

PIC18LF26J50T-I/ML - 8-bit USB MCU 64KB Flash 28-QFN | Microchip

The Microchip PIC18LF26J50T-I/ML is an 8-bit PIC microcontroller in the PIC18 J-series family with integrated full-speed USB 2.0 transceiver, 64 KB Flash program memory, and 3.8 KB RAM, housed in a 28-pin QFN (ML) package with exposed thermal pad. The LF prefix denotes the low-voltage variant operating from 2.0 V to 3.6 V, while the J50 family adds the on-chip USB 2.0 full-speed transceiver and nanoWatt XLP power management for battery-aware designs. An 8-bit PIC microcontroller (MCU) is a Harvard-architecture microcontroller using an enhanced RISC instruction set, a Flash program store and SRAM data memory, integrated peripherals such as timers, ADC, PWM, communication interfaces (UART, SPI, I2C), and increasingly USB. The PIC18F26J50 / PIC18LF26J50 sub-family is positioned in the mid-range PIC18 tier: more memory and more peripherals than PIC16, but simpler than the PIC24 / dsPIC. It is a drop-in replacement-friendly family with pinout compatibility across the PIC18F/LF24J50, 25J50 and 26J50 line. Key features include 64 KB on-chip Flash (32K x 16), 3.8 KB RAM, 1 KB EEPROM, 48 MHz internal oscillator (12 MIPS), 10-bit ADC up to 13 channels, two comparators, two CCP modules, two EUSART (LIN-capable) and one MSSP (SPI / I2C), plus on-board full-speed USB 2.0 with internal pull-up and 3.3 V regulator. The 'LF' variant operates down to 2.0 V supply, and the XLP nanoWatt technology provides sub-uA sleep currents for battery-powered applications. The architecture uses a 16-bit wide instruction path with an 8-bit data path, single-cycle hardware multiply, and a 31-level deep hardware stack. The integrated USB transceiver meets USB 2.0 full-speed (12 Mbps) requirements without external components other than the mandatory pull-up and decoupling. On-chip regulated 3.3 V from Vbus powers the USB transceiver even when the MCU is self-powered. Typical applications include USB HID class devices (keyboards, mice, game controllers), USB CDC virtual COM ports, low-cost data loggers, sensor interfaces with USB upload, consumer electronics with USB charging and data, industrial USB-to-UART bridges, and embedded learning platforms (this family is supported by MPLAB X IDE, XC8 compiler and the Microchip Code Configurator). When designing with this part, pay attention to the LF vs F suffix - the LF variant is the low-voltage (2.0-3.6 V) part and the F variant accepts 4.2-5.5 V. Both share the same pinout, so a board can be assembled with either. The QFN package requires thermal pad soldering for rated thermal performance and is recommended to be assembled by JLCPCB or professional SMT lines. This page combines distributor pricing, drop-in alternatives in the same 28-QFN package, and practical USB design notes that complement but do not replace the manufacturer datasheet.

Devis Contact
PIC18LF26J50T-I/SO - 64KB Flash USB MCU 28-SOIC | Microchip
PIC18LF26J50T-I/SO

PIC18LF26J50T-I/SO - 64KB Flash USB MCU 28-SOIC | Microchip

The Microchip Technology PIC18LF26J50T-I/SO is an 8-bit PIC microcontroller in the PIC18J family featuring Full-Speed USB 2.0, 64 KB of Flash program memory, 4 KB of RAM, and a 28-pin SOIC wide-body (7.50 mm) package. The "LF" prefix designates the low-voltage (F) core variant that operates from 2.0 V to 3.6 V with a 48 MHz internal oscillator equivalent (12 MIPS), while the "T" suffix denotes tape-and-reel packaging and "I/SO" indicates the industrial temperature grade (-40 °C to +85 °C) in the SOIC package. According to the manufacturer datasheet, this MCU integrates a Full-Speed USB 2.0 device/host/OTG transceiver, a 10-bit ADC with up to 13 channels, two analog comparators, two CCP/ECCP modules, and Microchip's nanoWatt XLP technology for ultra-low sleep currents below 100 nA. The PIC18 microcontroller family is an 8-bit Harvard-architecture RISC MCU line widely used in cost-sensitive embedded designs. The 18J sub-family specifically adds Full-Speed USB hardware on-chip, eliminating the need for an external PHY. Within the broader taxonomy, a PIC18 sits beneath the umbrella of "microcontroller" -> "8-bit MCU" -> "embedded controller" -> "semiconductor IC", and the 18J series occupies the middle of the PIC18 performance range, balancing USB connectivity with low power. Key differentiating features include 64 KB self-programmable Flash with 1 KB of dedicated EEPROM, a CTMU (Charge Time Measurement Unit) for capacitive touch and time-of-flight sensing, an enhanced instruction set with 16-bit instructions, and nanoWatt XLP power management with multiple deep-sleep modes. The integrated USB 2.0 Full-Speed transceiver with on-chip voltage regulator streamlines USB device designs without external crystals for low-speed/full-speed bus operation. Architecturally, the PIC18LF26J50T uses a modified Harvard core with a 16-bit instruction word and an 8-bit data path, two 31-level hardware stacks, and a vectored interrupt controller with two priority levels. The 28-SOIC package exposes up to 21 general-purpose I/O pins through peripheral pin select (PPS-less, fixed-pin) mappings and supports In-Circuit Serial Programming (ICSP) and In-Circuit Debug (ICD) via the standard Microchip two-wire interface. Typical applications include USB HID peripherals (mice, keyboards, custom input devices), USB-to-UART bridges, low-cost data loggers, sensor front-ends with capacitive touch, and battery-powered industrial sensors. The wide industrial temperature range and nanoWatt XLP modes make the part suitable for unattended remote nodes. Designers should note that the LF (low-voltage) core limits VDD to 2.0–3.3 V; designs requiring 5 V operation must select the non-LF "PIC18F26J50T-I/SO" sibling. The internal voltage regulator for USB requires a 5 V tolerant VBUS rail via an internal charge pump - consult the datasheet's USB section for the required capacitor network on VUSB/VCAP pins. This page synthesizes distributor pricing, drop-in alternatives within the same 28-SOIC footprint, and practical design notes covering the USB regulator network, low-power sleep mode selection, and ICSP/ICD pin allocation not found in the manufacturer datasheet.

Devis Contact
PIC18LF26J53-I/ML - 48MHz 8-bit USB MCU 64KB Flash | Microchip
PIC18LF26J53-I/ML

PIC18LF26J53-I/ML - 48MHz 8-bit USB MCU 64KB Flash | Microchip

The Microchip Technology PIC18LF26J53-I/ML is an 8-bit PIC18J-series microcontroller featuring 64KB Flash, 3.8KB RAM, integrated full-speed USB 2.0, a 12-bit ADC, and nanoWatt XLP power management, housed in a 28-pin QFN (ML) 6x6 mm package with exposed thermal pad. It operates at up to 48 MHz (12 MIPS) across an industrial -40C to +85C temperature range. What is a PIC18J-series microcontroller? PIC18J microcontrollers are Microchip's high-performance 8-bit MCU family in the broader PIC microcontroller -> 8-bit microcontroller -> microcontroller -> integrated circuit hierarchy. The 'J' suffix denotes parts with integrated USB 2.0 full-speed peripherals and high-memory-density Flash, while the 'LF' prefix indicates the low-voltage (2.0V-2.75V core) variant optimized for battery-powered applications. The 'XLP' (eXtra Low Power) nanoWatt technology extends deep-sleep currents into the nanoamp range. Key features include 64KB (32K x 16) Flash program memory, 3.8KB RAM, 1KB EEPROM, two USART, two MSSP (SPI/I2C) ports, 22-channel 12-bit ADC, two 10-bit DAC outputs, and a full-speed USB 2.0 device/OTG controller with on-chip transceiver. The 28-QFN package provides compact PCB integration while the exposed pad enables thermal dissipation for USB bus-powered designs. The PIC18J architecture uses a 16-bit modified Harvard instruction set with 8-bit data path. It incorporates peripheral pin select (PPS) for flexible I/O mapping, hardware RTCC with calendar mode, and a 4-deep CLC (Configurable Logic Cell) engine. The integrated USB transceiver eliminates the need for external PHY components. Typical applications include USB HID peripherals, USB-to-UART bridges, USB audio devices, low-power sensor hubs with USB connectivity, and battery-powered data loggers with USB charging. The wide peripheral integration suits PC accessories and embedded consumer products. When designing with this device, ensure proper decoupling (100 nF + 4.7 uF) close to VDD/AVDD pins and follow USB-IF compliance guidelines for bus-powered designs. The PPS feature requires configuration via code to map peripherals to specific I/O pins.

Devis Contact
PIC18LF26J53-I/SO - 8-bit 48MHz 64KB Flash USB MCU | Microchip
PIC18LF26J53-I/SO

PIC18LF26J53-I/SO - 8-bit 48MHz 64KB Flash USB MCU | Microchip

The Microchip Technology PIC18LF26J53-I/SO is a low-power, high-performance 8-bit PIC microcontroller featuring integrated full-speed USB 2.0, 64KB of Flash program memory, and 4KB of RAM, housed in a 28-pin SOIC package. It operates at up to 48MHz clock speed delivering 12 MIPS, supports 2.0V-3.6V core supply voltage, and includes a 10-bit ADC, multiple timers, and Microchip's nanoWatt XLP extreme low-power technology. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash/RAM), and peripherals on one silicon die. The PIC18 family is Microchip's enhanced 8-bit architecture sitting between baseline PIC10/12/16 and the 16-bit PIC24/dsPIC families. The 'LF' prefix denotes a wide-voltage low-power variant, the 'J' suffix indicates the J-series family with integrated USB, and '53' identifies the specific die with 64KB Flash. The PIC18LF26J53 belongs to the power management hierarchy of low-power MCUs used in battery-operated and USB-connected products. Key features include 64KB (32K x 16) Flash program memory, 4KB RAM, 22-channel 10-bit ADC, two analog comparators, enhanced CCP modules, four timers, two I2C, two SPI, and a full-speed USB 2.0 device/host/OTG transceiver. The device integrates a 3.3V voltage regulator for USB operation and supports deep sleep current below 100nA via nanoWatt XLP technology. The PIC18LF26J53 uses an enhanced Harvard RISC architecture with a 16-bit instruction word and 8-bit data path. The 48MHz internal oscillator with 4x PLL eliminates external crystals in most designs, and the integrated USB transceiver eliminates external USB PHY chips. The wide 2.0V-3.6V supply range with internal 3.3V regulation supports single-cell Li-ion or two-AA battery designs. Typical applications include USB peripherals, sensor hubs, low-power wireless sensor nodes, industrial data loggers, HID-class USB devices, and consumer electronics with USB connectivity. The combination of integrated USB, deep-sleep nanoWatt XLP modes, and rich peripherals makes it well-suited for cost-sensitive USB-aware embedded products. When designing with this device, note that the 28-SOIC package is the most common variant; for USB designs with dedicated D+/D- pins routing, follow the datasheet's PCB layout recommendations for the integrated 3.3V regulator. Designers should also verify the 'LF' supply voltage window (2.0V-3.6V) versus the non-LF 'F' variant (down to 2.0V) when selecting parts for 5V-tolerant applications. This page synthesizes distributor pricing across nine sources, drop-in same-family alternatives, and practical USB design notes not consolidated on the manufacturer product page.

Devis Contact
PIC18LF26J53T-I/ML - 64KB Flash USB MCU, 28-QFN | Microchip
PIC18LF26J53T-I/ML

PIC18LF26J53T-I/ML - 64KB Flash USB MCU, 28-QFN | Microchip

The Microchip PIC18LF26J53T-I/ML is a low-power 8-bit PIC microcontroller from the PIC18LFxxJ53 family, featuring 64 KB of Flash program memory, 4 KB of RAM, and an integrated full-speed USB 2.0 transceiver. Housed in a 28-pin QFN package (ML, 6x6 mm), the device operates from 2.0 V to 2.75 V and delivers up to 12 MIPS throughput. The 'LF' prefix denotes the low-voltage/F-range silicon revision optimized for portable and battery-powered designs, while the 'T' suffix indicates tape-and-reel packaging. What is a PIC18 microcontroller? PIC18 microcontrollers are 8-bit RISC microcontrollers from Microchip built on a Harvard architecture with a modified instruction set. They integrate Flash program memory, RAM, EEPROM, peripheral modules, and in many variants a USB transceiver, all on a single die. In the system hierarchy, a PIC18 sits below 16-bit dsPIC and 32-bit SAM/ARM Cortex-M parts but offers excellent code density, mature tooling, and integrated peripherals at very low cost. Key features of the PIC18LF26J53 include a 12-bit A/D converter with up to 10 channels, multiple serial interfaces (I2C/SPI/UART), an Enhanced USART, a 10-bit DAC reference, internal 31 kHz and 8 MHz oscillators, and up to 22 I/O pins. The integrated USB 2.0 full-speed transceiver with on-chip pull-ups simplifies USB device designs by eliminating external transceivers and reducing BOM cost. The 12 MIPS execution rate supports real-time control loops and USB enumeration without bottlenecks. The architecture combines a 16-bit instruction word with an 8-bit data path, an 8x8 hardware multiplier, a 4-deep FIFO for the A/D converter, and a priority interrupt controller. The internal voltage regulator of the J53 family can be configured for 2.5 V or 3.3 V core operation, and the wide I/O tolerance allows direct interface to 5 V peripherals in mixed-voltage systems when the regulator is properly bypassed. Typical applications include USB peripherals (HID, CDC, MSD), battery-powered sensor hubs, home automation controllers, low-cost data loggers, and small industrial HMI panels where the USB interface is the primary desktop-side connection and on-board peripherals drive actuators and displays. The 28-QFN footprint is also footprint-compatible with several other PIC18F2xJ53 variants, enabling easy migration across the family. When designing with this part, ensure the VUSB pin is connected to the USB VBUS through the internal pull-up configuration (per datasheet section 2.0 'Typical Application Connection'), and place the decoupling capacitor on VCAP/VDDCORE within 5 mm of the pin. A pull-up on MCLR is required if the device is used in production; tying MCLR directly to VDD prevents reliable reset behavior.

Devis Contact
PIC18LF26J53T-I/SO - 8-bit USB MCU 64KB Flash 12 MIPS | Microchip
PIC18LF26J53T-I/SO

PIC18LF26J53T-I/SO - 8-bit USB MCU 64KB Flash 12 MIPS | Microchip

The Microchip Technology PIC18LF26J53T-I/SO is a low-power 8-bit microcontroller from the PIC18 LF J53 family, featuring integrated USB 2.0 full-speed peripheral support and 64KB of Flash program memory in a 28-pin SOIC wide (7.50 mm) package. The device operates up to 48 MHz (12 MIPS instruction throughput) from a 2.0V to 3.6V supply and includes 4KB RAM, 12-bit A/D converter with up to 10 channels, multiple timers, and two USART/SPI/I2C peripherals. The "LF" prefix indicates the low-voltage core variant optimized for eXtreme Low Power (XLP) battery applications, while "T" denotes tape-and-reel packaging and "I" denotes the industrial -40C to +85C temperature range. An 8-bit PIC microcontroller is a Harvard-architecture RISC processor designed for embedded control. PIC MCUs sit within the broader microcontroller category, which itself belongs to the integrated circuits > microcontrollers hierarchy in power-managed embedded systems. The LF sub-family extends the legacy PIC18 line with nanoWatt XLP technology, internal voltage regulation, and ultra-low sleep currents that make these parts attractive for handheld, USB-bus-powered, and energy-harvesting designs. Key features include the integrated USB 2.0 full-speed transceiver and SIE, eliminating external USB PHY cost; 64KB self-programmable Flash with 10K erase cycles; 4KB linear RAM and 256-byte EEPROM; 10-bit or 12-bit A/D with auto-acquisition; mTouch capacitive touch support; and on-chip hardware RTCC for real-time clock backup. The CTMU peripheral enables accurate time and charge measurement for proximity sensing and capacitive buttons. The architecture is built on an enhanced PIC18 pipeline with hardware multiplier, 31-level stack, and C-friendly instruction set. The internal 31 kHz to 8 MHz oscillator block plus 48 MHz USB clock source minimize external components, while two comparators and a reference DAC provide analog signal conditioning. XLP nanoWatt technology delivers typical sleep currents below 100 nA with RTCC enabled. Typical applications include USB HID peripherals such as mice, keyboards, and game controllers, low-power sensor hubs, USB-to-UART bridges, and human-interface devices. The combination of integrated USB, ample RAM for USB endpoint buffers, and XLP sleep modes makes the LF26J53 a frequent choice for tethered battery peripherals and bus-powered IoT edge nodes. When designing with this part, allocate enough Flash for the USB stack and CDC/HID class driver (typically 10-14KB), and follow Microchip's USB PCB layout guidelines including a 90-ohm differential impedance on D+/D- and a common-mode choke near the connector. The 28-SOIC wide footprint is the same as PIC18F/LF2553 and PIC18F/LF25K22, simplifying board upgrades. This page synthesizes distributor pricing, same-family pin-compatible alternatives, and practical USB design notes not found in the standalone Microchip datasheet.

Devis Contact
PIC18LF26K22-E/ML - 64KB Flash, 64MHz 8-bit MCU | Microchip
PIC18LF26K22-E/ML

PIC18LF26K22-E/ML - 64KB Flash, 64MHz 8-bit MCU | Microchip

The Microchip Technology PIC18LF26K22-E/ML is an 8-bit high-performance RISC microcontroller belonging to the PIC18F/LF K22 family, integrating 64KB of Flash program memory and 3968 bytes of SRAM in a 28-pin QFN (ML) package with nanoWatt eXtreme Low-Power (XLP) technology. The core runs at up to 64MHz, delivering up to 16 MIPS while operating from a 1.8V to 3.6V supply, which makes it ideal for battery-powered designs that demand both computational throughput and low quiescent current. A microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), and programmable peripherals into one package. The PIC18 family is Microchip's high-pin-count, high-memory 8-bit line; nanoWatt XLP is the marketing label for the power-management features that allow deep-sleep currents in the sub-microamp range. Within the broader taxonomy, the PIC18LF26K22 occupies the LDO-class low-voltage LF slot of Microchip's 8-bit portfolio, sitting between the legacy PIC16 mid-range parts and the 16-bit PIC24/dsPIC families. Key features include 64KB Flash with self-programmability, 3968 bytes of RAM, 1024 bytes of EEPROM, two Enhanced USART modules, two MSSP (SPI/I2C) ports, an Enhanced Capture/Compare/PWM (ECCP) module, a 10-bit ADC with up to 28 analog channels, and nanoWatt XLP sleep currents as low as 30 nA in deep-sleep mode. The wide operating voltage range of 1.8V to 3.6V lets the part run directly from a single Li-Ion cell or two AA batteries, while peripherals like the RTCC and Ultra-Low-Power Wake-up keep standby consumption measured in nanoamps. Architecturally, the PIC18LF26K22 uses a 16-bit modified Harvard architecture with a hardware multiply and 31-level hardware stack, distinguishing it from the 14-bit PIC16 mid-range parts and giving software developers higher code density per instruction. The 28-pin QFN package exposes the full peripheral set including up to 28 ADC channels through digital I/O reassignment, making the silicon equally suited for sensor aggregation, user I/O, and motor control roles in compact layouts. Typical applications include wearable health and fitness devices, low-power wireless sensor nodes, battery-powered metering, USB-to-UART bridge dongles, and general-purpose consumer/industrial control. The combination of 64KB Flash and nanoWatt XLP makes it a frequent choice for designs that need room for a USB stack, a wireless protocol, or a graphical HMI on a long-life battery. When designing with the E temperature grade, observe the -40C to +125C ambient window and follow the in-circuit serial programming (ICSP) timing diagrams from the Microchip datasheet when a debugger/programmer header is added. For engineering reviews, note that the 'LF' prefix indicates 1.8V-3.6V operation; migrating to the PIC18F26K22 version is the standard upgrade path when a 5V-tolerant 1.8V-5.5V supply rail is needed instead. This XAIPART product page synthesizes live distributor pricing, drop-in alternatives within the PIC18 K22 family, AEO-optimized design notes, and a parametric comparison table that goes beyond the manufacturer datasheet front page to speed up your part-selection decision.

Devis Contact
PIC18LF26K22-E/SO - 64KB Flash 8-bit XLP MCU, 28-SOIC | Microchip
PIC18LF26K22-E/SO

PIC18LF26K22-E/SO - 64KB Flash 8-bit XLP MCU, 28-SOIC | Microchip

The Microchip Technology PIC18LF26K22-E/SO is a 28-pin SOIC, 8-bit PIC18 microcontroller featuring 64KB of Flash program memory, 3968 bytes of RAM, and a maximum CPU clock speed of 40 MHz, designed on the eXtreme Low Power (XLP) nanoWatt architecture. It operates over a supply voltage range of 4.2V to 5.5V, with 34 digital I/O pins, an integrated 10-bit ADC, multiple PWM modules, and standard communication peripherals including UART, SPI, and I2C. A PIC microcontroller (MCU) is a compact programmable processor that integrates CPU, memory, and peripherals on a single silicon die. PIC microcontrollers from Microchip sit at the intersection of 8-bit microcontrollers -> RISC microcontroller -> embedded controller -> semiconductor IC, and have been a foundational building block of embedded systems since the 1990s. They are widely used in applications where deterministic behavior, low power, and a mature toolchain (MPLAB X IDE, XC8 compiler) are valued. Key features of the PIC18LF26K22 family include nanoWatt XLP technology for sleep currents down to the nanoampere range, peripheral flexibility with multiple capture/compare/PWM modules, an enhanced 8/16-bit timer block, and a wide operating temperature range. The 'LF' prefix designates the wide-voltage-range silicon variant, while the 'E' suffix indicates the Extended (industrial) temperature grade of -40C to +125C. The 28-SOIC (SO) package is a JEDEC-standard 300-mil plastic small-outline package suitable for hand-soldering and reflow on conventional PCBs. Typical applications include low-power sensor nodes, battery-operated handheld instruments, industrial control front-ends, automotive body electronics (non-AEC-Q100 grade), USB device interfaces when paired with the PIC18F/K series, and educational/development boards. The on-chip 10-bit ADC and CTMU (Charge Time Measurement Unit) make the device well suited to capacitive touch and analog sensing. When designing with this MCU, ensure decoupling capacitors of 100 nF and 10 uF are placed close to VDD/VSS, that the MCLR pin has a proper pull-up, and that unused I/O are configured as outputs low to minimize current. For migration to smaller packages, the same die is offered in 28-QFN (PIC18LF26K22-E/ML) and 40-PDIP/SPDIP form factors.

Devis Contact
PIC18LF26K22-E/SS - 64KB Flash 8-bit nanoWatt XLP MCU | Microchip
PIC18LF26K22-E/SS

PIC18LF26K22-E/SS - 64KB Flash 8-bit nanoWatt XLP MCU | Microchip

The Microchip PIC18LF26K22-E/SS is a low-power, high-performance 8-bit PIC microcontroller with 64KB Flash, 3,968 bytes of RAM, and a 48 MHz internal oscillator, housed in a 28-pin SSOP package. The LF variant operates from a wide 1.8V to 3.6V supply range and integrates nanoWatt eXtreme Low Power (XLP) technology that drops sleep current to a few tens of nanoamps. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and programmable peripherals on one die. The PIC18 family sits in the 8-bit RISC category of MCUs, which trades raw clock speed for deterministic instruction timing, predictable interrupt latency, and a compact C-friendly instruction set. PIC18 devices are typically chosen over 16-bit and 32-bit parts when BOM cost, code simplicity, and ultra-low sleep current are more important than arithmetic throughput. Within the Microchip portfolio, PIC18 belongs to the larger microcontroller -> embedded MCU -> semiconductor taxonomy. Key features of the PIC18LF26K22-E/SS include 64KB (32K x 16) self-programmable Flash, 256 bytes of EEPROM, a 12-bit ADC with up to 19 channels, two Enhanced USART modules, two MSSP (SPI/I2C) peripherals, and a 5-bit DAC. The device also supports capacitive touch sensing via the mTouch framework and integrates a 16-bit timer/counter with capture/compare. Architecturally the PIC18LF26K22 uses an 8-bit RISC core with hardware multiply, a 16-bit instruction word, and a vectored interrupt controller. The wide operating voltage window (1.8-3.6V) makes it ideal for direct connection to a single-cell Li-ion or 2xAA battery, while the nanoWatt XLP sleep modes extend battery life in intermittently active products. Typical applications include battery-powered sensor nodes, low-cost consumer appliances, touch-interface front panels, industrial control modules, and portable medical devices such as glucose meters or spirometers. The combination of EEPROM, multiple serial interfaces, and rich analog peripherals enables single-chip implementation of many mixed-signal embedded designs. When designing with this part, keep in mind that the "E" suffix denotes the -40C to +125C extended temperature grade and the "LF" prefix denotes the low-voltage core variant. Decoupling the AVDD/AVSS analog rails separately from VDD/VSS reduces ADC noise, and unused I/O pins should be configured as outputs low to minimize sleep current. Designers migrating from the PIC18F26K22 (F = 1.8-5.5V) need to re-validate analog performance, because several analog specs degrade at the LF lower input rail. This page synthesizes distributor pricing, pin-compatible PIC18 alternatives, and practical low-power design notes not found in the bare manufacturer datasheet.

Devis Contact
PIC18LF26K22-I/SO - 64KB Flash 8-bit MCU XLP 28-SOIC | Microchip
PIC18LF26K22-I/SO

PIC18LF26K22-I/SO - 64KB Flash 8-bit MCU XLP 28-SOIC | Microchip

The Microchip Technology PIC18LF26K22-I/SO is a low-power, high-performance 8-bit PIC microcontroller from the PIC18 K22 family with 64KB Flash, 3,968 bytes SRAM and 1,024 bytes EEPROM, housed in a 28-pin SOIC package rated for the industrial -40C to +85C temperature range. The device runs at up to 64 MHz (16 MIPS instruction throughput), integrates a 10-bit ADC up to 17 channels, multiple Enhanced USART, MSSP and CCP/ECCP peripherals, and qualifies for the -LF 1.8V-3.6V voltage variant suited to single-cell Li-Ion designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM/EEPROM) and a configurable set of peripherals - ADC, timers, communication interfaces and GPIO - on one piece of silicon. MCUs sit at the lowest tier of the embedded computing hierarchy, below microprocessors (MPU) and far below SoCs, and are the workhorses of embedded designs because they consolidate control logic, I/O and signal conditioning into one programmable part. The PIC18 family is Microchip's 8-bit baseline architecture, and the K22 sub-family specifically targets low-power (nanoWatt XLP) portable and battery applications. Key features include nanoWatt XLP extreme-low-power technology with multiple sleep modes down to sub-microampere leakage, 25 general-purpose I/O pins with interrupt-on-change, two Enhanced USART modules supporting LIN and IrDA, two MSSP ports (I2C/SPI), three CCP plus one ECCP module for PWM/motor control, and a 10-bit ADC with up to 17 channels and automatic acquisition. The -LF voltage variant operates from 1.8V to 3.6V. Architecturally, the PIC18LF26K22 uses a RISC Harvard-style core with a 16-bit instruction word, an 8-bit data path, and a hardware multiplier that simplifies time-critical math versus pure 8-bit accumulator cores. The 64 MHz Fosc derives from an internal 16 MHz HFINTOSC plus a 4x PLL block, allowing firmware to tune CPU speed on the fly via OSCTUNE to trade throughput for current consumption. Typical applications include low-power sensor nodes, handheld instrumentation, USB-to-UART bridges (with a companion MCP2200), small motor control, battery chargers, and industrial control panels that need 5V-tolerant GPIO or XLP sleep profiles. Design consideration: choose the -LF (1.8V-3.3V) variant rather than the -F (1.8V-5.5V) when your design runs from a single Li-Ion or two AA cells; this trade-off costs 5V tolerance but saves tens of microamperes in active run current. This page synthesizes distributor pricing, drop-in same-package alternatives (PIC18LF26K22 family members and PIC18F26K22-I/SO), datasheet-cited electrical parameters, and practical design notes not found in a single distributor listing, giving engineers an AEO-friendly comparison surface for component selection.

Devis Contact
PIC18LF26K22-I/SS - 8-bit XLP MCU, 64KB Flash, 28-SSOP | Microchip
PIC18LF26K22-I/SS

PIC18LF26K22-I/SS - 8-bit XLP MCU, 64KB Flash, 28-SSOP | Microchip

The Microchip PIC18LF26K22-I/SS is an 8-bit PIC18 microcontroller built on the nanoWatt XLP low-power platform, offering 64KB of Flash program memory and 3968 bytes of RAM in a 28-pin SSOP package. It operates across a wide 1.8V to 3.6V supply range with up to 64MHz CPU performance (16 MIPS at 64MHz internal), making it suitable for both battery-powered and line-powered embedded designs. The "LF" prefix designates the low-voltage F-variant with extended nanoWatt XLP features. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O into one package. The PIC18 family uses Microchip's enhanced 8-bit RISC architecture with hardware multiplier and C-friendly design. Within the broader taxonomy, the PIC18LF26K22 sits as: microcontroller -> 8-bit MCU -> PIC18 family -> PIC18 "K22" sub-family -> PIC18LF26K22 (low-voltage, 28-pin, 64KB Flash). It is the foundation of millions of embedded products in consumer, industrial, and automotive-grade (with Q-graded parts) applications. Key differentiating features of the PIC18LF26K22 include the nanoWatt XLP technology with deep-sleep current in the nanoamp range, integrated mTouch capacitive sensing peripherals, two Enhanced USART modules, two MSSP (SPI/I2C) ports, two CCP/ECCP modules, a 12-channel 10-bit ADC, and four 8-bit timers plus five 16-bit timers. The CTMU peripheral enables capacitive touch and time measurement without external components. The on-chip 64MHz internal oscillator reduces BOM by eliminating an external crystal in many designs. Typical applications include low-power battery sensor nodes, USB HID peripherals (when paired with the F-variant's USB module), home appliances, motor-control BLDC/PMSM drivers using ECCP, capacitive touch keypads with mTouch, and industrial IoT edge nodes. The wide operating voltage (1.8V-3.3V typical, 3.6V max) lets a single part cover 2xAA, Li-ion, and 3.3V regulated rails. A key design consideration: at 64MHz and 3.3V the core draws ~10mA (typical), so coin-cell designs must use nanoWatt XLP sleep modes (down to ~20nA). For multi-rail systems, the brown-out reset (BOR) and PWRT timers should be enabled to ensure deterministic startup. The I/SS package is the industrial (-40C to +85C) temperature grade with SSOP-28 footprint.

Devis Contact
PIC18LF26K22T-I/SO - 8-bit XLP MCU 64KB Flash 28-SOIC | Microchip
PIC18LF26K22T-I/SO

PIC18LF26K22T-I/SO - 8-bit XLP MCU 64KB Flash 28-SOIC | Microchip

The Microchip Technology PIC18LF26K22T-I/SO is an 8-bit PIC18 XLP microcontroller with 64KB Flash, 3.9KB RAM, and a 64MHz CPU, housed in a 28-pin SOIC package. It is the LF (low-voltage) variant of the PIC18F26K22 family, supporting operation from 1.8V to 3.6V. The 'T' suffix denotes Tape & Reel packaging, and the 'I' is the industrial temperature grade (-40C to +85C). A microcontroller (MCU) is a single-chip computer containing a CPU, Flash program memory, RAM, and configurable peripherals such as ADC, UART, I2C, SPI, timers, and PWM. PIC18 XLP parts add nanoWatt XLP technology for ultra-low sleep currents below 50 nA typical. Within the broader taxonomy, MCUs sit at the embedded controller level - above 8-bit processors but below application processors and microprocessors. Key features include nanoWatt XLP extreme low-power technology, an integrated 10-bit A/D converter with up to 19 channels, multiple communication peripherals (UART, SPI, I2C), PWM modules, and the standard PIC18 peripheral set. The CPU executes instructions at 64MHz (16 MIPS) thanks to a 4-cycle pipeline, while flexible oscillator options include internal 16MHz HF and 31kHz LF sources. Architecturally, the PIC18LF26K22 uses an enhanced Harvard architecture with separate program and data buses, a 16-bit instruction word, and a rich instruction set. The LF process is optimized for low-voltage operation, which is why the datasheet specifies 1.8V-3.6V (compared to the F variant's 2.3V-5.5V range). Peripherals XLP variants reduce active current below typical PIC18 levels, making them ideal for battery-powered applications. Typical applications include IoT sensor nodes, battery-powered metering devices, low-power remote controls, HVAC thermostats, and portable industrial instruments. Anywhere a coin-cell or two-AA battery must last years, this MCU's XLP features become attractive. When designing with this device, choose the LF variant (1.8V-3.6V) if the system is battery-powered or uses a regulated 3.3V rail; choose the F variant if a 5V rail is available without regulation. The 'T' suffix only affects packaging - the die is identical to the non-T version, so firmware developed on PIC18LF26K22-I/SO ports directly to the T variant. This page synthesizes distributor pricing from DigiKey, Mouser, and LCSC, plus drop-in SOIC alternatives and practical design notes not aggregated on a single manufacturer datasheet page.

Devis Contact
PIC18LF26K40-E/ML - 64KB Flash XLP 8-bit MCU 28-QFN | Microchip
PIC18LF26K40-E/ML

PIC18LF26K40-E/ML - 64KB Flash XLP 8-bit MCU 28-QFN | Microchip

The Microchip PIC18LF26K40-E/ML is an 8-bit PIC18 RISC microcontroller delivering 64KB Flash and 64MHz core speed in a 28-pin QFN (6x6 mm) package with exposed pad. The device supports a wide 1.8V to 3.6V operating voltage range and includes Microchip's eXtreme Low-Power (XLP) technology for battery-friendly applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), peripherals, and I/O into one package. PIC18-series MCUs add 16-bit wide instruction paths and hardware multiply to the classic 8-bit PIC architecture, occupying the layer: PIC18 -> PIC microcontroller -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC18LF26K40 sits inside Microchip's mid-density "K40" sub-family, balancing high computational performance with rich Core Independent Peripherals. Key features include 64KB (32K x 16) Flash program memory, 3,584 bytes of RAM, 1KB of EEPROM, an internal 64MHz oscillator, and a 10-bit ADC with Computation (ADCC) that automates Capacitive Voltage Divider (CVD) operations for advanced touch and sensing tasks. The device also integrates Complementary Waveform Generator (CWG), Windowed Watchdog Timer (WWDT), CRC/Memory Scan, Zero-Cross Detect, Peripheral Pin Select (PPS), and up to 25 I/O pins. Five packages (28/40/44-pin) form the PIC18(L)F26K40 family. Typical applications include low-power IoT sensor nodes, consumer appliances with touch interfaces, battery-powered handheld instrumentation, automotive body and HVAC control modules, and industrial control panels. The XLP sleep currents below 50 nA make it especially suitable for energy-harvesting or always-on designs where battery lifetime is critical. When designing with the PIC18LF26K40-E/ML, note that the "-E" suffix denotes the Extended temperature grade (-40C to +125C), while "-I" denotes Industrial (-40C to +85C). The exposed thermal pad on the QFN package must be soldered to a ground copper pour for both thermal dissipation and electrical performance; omitting this typically degrades ADC noise and may exceed datasheet thermal limits. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, including a curated replacement list drawn from Microchip's own FFF (Form-Fit-Function) alternate catalogue.

Devis Contact
PIC18LF26K40-E/MV - 64KB Flash 8-bit MCU, 28-UQFN | Microchip
PIC18LF26K40-E/MV

PIC18LF26K40-E/MV - 64KB Flash 8-bit MCU, 28-UQFN | Microchip

The Microchip Technology PIC18LF26K40-E/MV is an 8-bit PIC® XLP™ microcontroller running up to 64 MHz with 64 KB Flash, 3720 bytes of RAM, and 1 KB data EEPROM, packaged in a 28-pin UQFN (4x4 mm) with exposed pad. It supports an extended operating voltage range down to 1.8 V (LF variant) up to 3.6 V, making it well-suited for battery-powered and energy-harvesting designs. The MCU integrates rich on-chip peripherals including a 10-bit ADC with computation (ADC2), a 5-bit DAC, comparators, PWM, CCP, CWG, HLT, WWDT, CRC/SCAN, ZCD, and Peripheral Pin Select (PPS), plus dual I²C, dual SPI, and dual EUSART interfaces. An 8-bit microcontroller (MCU) is a small computer-on-a-chip that integrates a CPU, program memory (Flash), data memory (RAM/EEPROM), and peripherals on a single die. 8-bit MCUs sit below 16-bit and 32-bit devices in raw compute throughput but win on cost, deterministic interrupt latency, and ultra-low sleep current. PIC18 (8-bit) MCUs from Microchip form the upper end of the 8-bit tier, offering high peripheral integration and XLP (eXtreme Low Power) technology with sleep currents in the nanoamp range for IoT and battery applications. Key differentiating specifications include the 10-bit ADC2 with automatic averaging and threshold comparison, CWG (Complementary Waveform Generator) for hardware dead-band control, 5-bit DAC for analog setpoints, ZCD (Zero-Cross Detect) for AC line control, and CRC/SCAN for memory integrity. Core Independent Peripherals allow hardware state machines to run without waking the CPU, reducing average power dramatically. Typical applications include IoT sensor nodes, industrial sensor conditioning, LED lighting controllers, AC line power control (using ZCD + CWG), battery chargers, and compact consumer appliances that need USB-style connectivity without a USB PHY (via the dual EUSART/SPI bridging). The 28-UQFN 4x4 mm package makes it ideal for space-constrained PCBs. When designing, place a 100 nF decoupling capacitor on each VDD pin and connect the exposed pad (EP) to a solid ground plane for thermal dissipation. The PPS system lets you remap most digital peripherals to almost any I/O, simplifying PCB layout. Use the ADC2 computation mode to offload averaging and threshold detection from the CPU. This page synthesizes XAIPART distributor pricing, drop-in pin-compatible alternatives within the PIC18 LF family, and practical design notes not bundled in the manufacturer datasheet.

Devis Contact
PIC18LF26K40-E/SP - 8-Bit 64MHz XLP MCU 64KB Flash | Microchip
PIC18LF26K40-E/SP

PIC18LF26K40-E/SP - 8-Bit 64MHz XLP MCU 64KB Flash | Microchip

The Microchip Technology PIC18LF26K40-E/SP is an 8-bit RISC microcontroller based on the PIC18 enhanced CPU core, delivering up to 64 MHz of computational performance with 64 KB of Flash program memory in a 28-pin SPDIP (0.300" through-hole) package. It integrates 4 KB of data RAM, 256 bytes of EEPROM, and a rich analog/digital peripheral set including a 10-bit ADC with Computation (ADC2), a 5-bit DAC, comparators, multiple PWM/CCP/CWG channels, HLT, WWDT, CRC/SCAN, and ZCD peripherals that target low-power and functional-safety-oriented designs. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, RAM, non-volatile program memory, and peripherals onto one silicon die; the PIC18 architecture sits within Microchip's hierarchy of 8-bit microcontrollers (PIC10/12/16/18) -> RISC MCU -> microcontroller -> embedded processor -> semiconductor. The "LF" prefix denotes the extended low-power (XLP) family, optimized for battery-operated and energy-harvesting designs where quiescent current in nanoampere ranges is mandatory. The device operates from 1.8 V to 3.6 V (LF variant) and supports up to 16 MIPS at 64 MHz. It features Core Independent Peripherals (CIPs) such as the Complementary Waveform Generator (CWG), Windowed Watchdog Timer (WWDT), and Cyclic Redundancy Check with Memory Scan (CRC/SCAN) that offload tasks from the CPU and improve deterministic real-time response. The 10-bit ADC2 includes hardware accumulation, averaging, threshold detection, and automatic channel scanning, reducing firmware overhead for sensor-array applications. Typical applications include IoT sensor nodes, battery-powered instrumentation, home automation controllers, low-power wireless sensor platforms, and consumer appliances. The integrated ZCD, CWG, and analog peripherals make it well suited for SMPS control loops and motor/lighting control where deterministic hardware response is required. Designers should review the device's power-budget calculator and clock-tree configuration in MPLAB X IDE to balance active current, sleep current, and wake-up latency. The 28-pin SPDIP footprint supports breadboard and through-hole prototyping, while surface-mount variants (SOIC/SSOP/QFN/ML) of the same die are available for production reflow assembly. This page synthesizes distributor pricing, drop-in same-family alternatives from Microchip, and practical design notes that supplement - but do not replace - the manufacturer datasheet and the MPLAB XC8 compiler documentation.

Devis Contact
PIC18LF26K40-E/SS - 64KB Flash XLP 8-bit MCU, SSOP-28 | Microchip
PIC18LF26K40-E/SS

PIC18LF26K40-E/SS - 64KB Flash XLP 8-bit MCU, SSOP-28 | Microchip

The Microchip Technology PIC18LF26K40-E/SS is a 28-pin, ultra-low-power (XLP) 8-bit PIC microcontroller built on the enhanced mid-range PIC18 core, integrating 64KB of Flash program memory, 4KB of SRAM, and 256 bytes of EEPROM in a 28-SSOP package. It executes instructions at up to 64 MHz from a 1.8V-3.6V supply, with peripheral-rich integration including a 10-bit ADC with computation (ADC2), a 5-bit DAC, comparators, configurable logic cells (CLC), complementary waveform generator (CWG), windowed watchdog timer (WWDT), CRC/SCAN, zero-cross detect (ZCD), and peripheral pin select (PPS) for flexible signal routing. An 8-bit microcontroller (MCU) is a single-chip processor with an 8-bit data bus width, internal program memory, RAM, and integrated peripherals like ADC, timers, and communication interfaces. Within the MCU taxonomy, the PIC18LF26K40 belongs to the PIC18 family -> 8-bit PIC microcontrollers -> microcontrollers -> microcontrollers and processors -> semiconductor ICs, positioning it for general-purpose embedded control rather than high-performance DSP workloads. Key differentiating features include nanoWatt XLP technology for sub-µA sleep currents that extend battery life, eXtreme Low-Power (XLP) modes with typical <100 nA sleep draw, PPS for remapping digital peripherals to nearly any I/O pin (reducing PCB layout constraints), and Core Independent Peripherals (CIPs) such as CWG and WWDT that operate without CPU intervention. The 'LF' prefix denotes the low-voltage (1.8V-3.6V) variant designed for battery-powered and energy-harvesting systems. Architecturally, the device uses a 16-bit instruction word with an 8-bit data path, hardware multiply, and a vectored interrupt controller supporting prioritized interrupts. The integrated high-frequency oscillator and PLL eliminate external crystals for many timing needs, while the IDLE/DOZE/PMD power-management modes let developers trade peripheral activity against current draw at runtime. Typical applications include IoT sensor nodes, battery-powered remote controls, low-end consumer electronics, industrial sensor interfaces, and automotive body controllers. Designers select this MCU when they need generous Flash/RAM, robust I/O count, and proven low-power PIC18 toolchain support. Design consideration: leverage PPS to remap EUSART/SPI/I2C to any available pin, simplifying PCB routing; always place the ICSPDAT/ICSCLK pins to accessible test points for in-circuit programming and debugging. This page consolidates distributor pricing tiers (as of 2026-09-28), verified drop-in alternatives (same SSOP-28 package), and practical design notes synthesized from Microchip datasheets not commonly seen on distributor listings.

Devis Contact
PIC18LF26K40-I/MV - 64KB Flash 8-Bit XLP MCU | Microchip
PIC18LF26K40-I/MV

PIC18LF26K40-I/MV - 64KB Flash 8-Bit XLP MCU | Microchip

The Microchip Technology PIC18LF26K40-I/MV is an 8-bit PIC18 microcontroller built on the eXtreme Low-Power (XLP) platform, delivering up to 64 MHz operation with 64 KB of Flash program memory, 4 KB of SRAM, and 256 bytes of EEPROM in a compact 28-pin UQFN (MV) package measuring 4x4 mm. A microcontroller is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals; the PIC18 family is Microchip's 8-bit architecture that combines RISC-like efficiency with rich on-chip peripherals for embedded control. Within that hierarchy, the LF variant denotes the low-voltage core (1.8 V to 3.6 V operation), the K40 generation adds Core Independent Peripherals and 5 V tolerant I/O, and the "26" pin-count signals a 28-pin package option. This positions the LF26K40 as a power-aware general-purpose MCU spanning the PIC18 -> 8-bit MCU -> microcontroller -> embedded IC taxonomy. Key specifications include a 64 MHz internal oscillator (16 MIPS instruction throughput), a 10-bit ADC with up to 24 channels, a 5-bit DAC, complementary waveform generators (CWG), hardware limit timers (HLT), windowed watch-dog timer (WWDT), zero-cross detection (ZCD), CRC/SCAN, and peripheral pin select (PPS) for flexible signal routing. The device operates from 1.8 V to 3.6 V with nanoWatt XLP sleep currents that suit battery-powered designs. The architecture couples a 16-bit wide instruction path with an 8-bit data path, delivering deterministic interrupt latency while keeping peripheral interaction intuitive. The XLP technology integrates multiple low-power modes (sleep, doze, idle, peripheral module disable) with retention RAM and a RTCC, allowing designs to draw microamps while still maintaining real-time responsiveness. Typical applications include consumer IoT sensor nodes, battery-powered medical wearables, industrial HMI keypads, low-power wireless sensor hubs, and home appliance user-interface boards. The wide 1.8-3.6 V supply range suits single-cell Li-ion or 2x AA operation without additional boost converters. When selecting this part, verify that your code base targets the K40 errata and PPS register set because the PPS subsystem differs from earlier PIC18F K-series devices. Designers transitioning from PIC18F25K22 or PIC18F26K22 should recompile against the XC8 K40 device pack to avoid peripheral library mismatches. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design considerations not bundled in the manufacturer datasheet, giving engineers a faster path to a validated 8-bit design.

Devis Contact