Gestion de l'alimentation
Sous-catégories
Produits (2819)
MWCT1000CFM - 5W Qi Wireless Charging TX PMIC | NXP | QFN-32
The NXP Semiconductors MWCT1000CFM is a 5 W, single-coil, Qi-compliant wireless charging transmitter PMIC in a 5x5 mm 32-pin HVQFN package with integrated digital demodulation. It supports the latest low-power WPC Qi specifications and provides the complete controller functionality for building a 5V standard wireless-charging transmitter solution. A wireless charging transmitter PMIC is a power management integrated circuit that drives a transmitter coil to deliver energy to a Qi-compatible receiver via resonant inductive coupling. The PMIC sits in the power management IC hierarchy between discrete analog transmitter controllers and full System-on-Chip wireless power platforms, combining a power stage, demodulation, FOD (Foreign Object Detection) algorithms, and fault protection in one device. Key features include wide DC input voltage support starting at 4.2V, with typical rails of 5V, 12V and 19V, on-chip digital demodulation compatible with all standard Qi receiver modulation strategies (AC capacitor, AC resistor and DC resistor), two configurable re-pins that can drive LEDs for system status indication (charging, standby, fault), and integrated foreign-object detection using the power-loss method. The 32-HVQFN (5x5) exposed-pad package provides a low thermal-resistance path for the integrated power stage. Architecturally, the MWCT1000CFM combines an analog power stage, a digital control core running the WCT software library, on-chip demodulation hardware, and configurable GPIO. The WCT library implements the Qi communication protocol, power transfer control, FOD via power-loss measurement, system status indication, and fault protection. Designers obtain the full Qi stack as binary firmware rather than writing a protocol stack from scratch. Typical applications include 5V Qi-certified wireless charging pads for smartphones, single-coil low-power charging bases for wearables and earbuds, automotive Qi charging modules, and embedded wireless power in industrial and medical devices. The 5W rating makes it well suited to handset-tier charging rather than laptop or kitchen-appliance tiers. When designing with the MWCT1000CFM, observe coil matching, resonant-capacitor selection, and thermal layout. The exposed pad must be soldered to a sufficiently large copper pour to keep junction temperature within limits at continuous 5W transmission, and the digital demodulation input network must be tuned to the chosen coil geometry. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet to help engineers select and source the part quickly.
MWCT1101CLH - 5W Single-Coil Wireless Charging Tx PMIC
The NXP MWCT1101CLH is a 5W, single-coil, 5V-input, premium wireless charging transmitter PMIC housed in a 64-pin LQFP (10x10 mm) package, optimized for WPC Qi-compliant transmitter designs that demand a small BOM, low standby power, and Qi interoperability. The device integrates a digital controller, full-bridge inverter driver, current/voltage sensing, and foreign object detection (FOD) on a single die, providing complete controller functionality for implementing a wireless charging transmitter solution. A wireless charging transmitter PMIC belongs to the broader wireless-power transfer (WPT) product family, sitting hierarchically under power management ICs and specialized PMICs. These devices drive a transmitter coil with a regulated AC waveform; power-transfer efficiency, foreign-object detection, and Qi protocol compliance are the headline concerns. The MWCT1101CLH targets the consumer 5W Qi baseline (Baseline Power Profile, BPP, equivalent to ~5V at up to 1A through the LC tank at resonance). Key features include single-coil support (WPC A5/A11/A12/A15 coil topologies), Qi interoperability via NXP's firmware library, integrated digital demodulation, adaptive foreign-object detection, and adaptive dead-time control to maximize efficiency across load range. The device supports 5V typical input (e.g., USB or 5V rail) and produces the AC coil current required for a 5W transmitter stage. A UART/I2C peripheral interface allows a host MCU to update firmware, query status, and run diagnostics, while firmware resides in external flash. Architecturally, the MWCT1101CLH embeds an on-chip digital state machine plus dedicated analog front-end for current sensing, voltage sensing, and FOD; this mixed-signal architecture simplifies layout versus discrete implementations. The integrated gate drivers for the full-bridge (typically N-MOSFET half-bridge pair) reduce external part count and ease EMI compliance. Typical applications include smartphone wireless charging pads, gaming-mouse and earbud-case wireless charging stands, and embedded furniture charging surfaces; the small LQFP-64 footprint and low-BOM external count also make it attractive for medical and industrial 5W charging cradles. NXP's reference designs emphasize easy Bluetooth/Wi-Fi coexistence by tuning switching frequency and dithering to reduce EMI coupling. When designing with the MWCT1101CLH, follow NXP's reference PCB layout closely: keep the coil-to-tank capacitor loop area minimal, provide adequate ground pour around the device, and ensure the host MCU firmware is built against NXP's latest Qi library to maintain interoperability with Qi-certified receivers. This page synthesizes distributor pricing, pin-compatible firmware-compatible drop-in alternatives, and practical design notes beyond the bare manufacturer datasheet.
MWCT1200CFM - 5W Multi-Coil Wireless Charging Tx IC | NXP
The NXP Semiconductors MWCT1200CFM is a 5 W multi-coil wireless charging transmitter IC integrating a full Qi-compliant A5/A11 controller, FSK/ASK modulation demodulation, and foreign object detection (FOD) in a 32-pin HVQFN (5x5 mm) package. The device operates from a 2.7 V to 3.6 V supply and draws 300 µA of supply current, making it suitable for 5 V input wireless-charging-pad designs based on the WPC medium-power specification. What is a wireless charging transmitter IC? A wireless charging transmitter IC (PMIC) is a specialized power management unit that drives a transmitter coil to deliver energy to a Qi-compliant receiver through resonant inductive coupling. The transmitter sits inside the category hierarchy: PMIC -> power management IC -> wireless power transmitter -> semiconductor. It is responsible for half-bridge or full-bridge coil driving, closed-loop current regulation based on Qi protocol packets, digital demodulation of load-modulated messages from the receiver, and safety functions such as over-temperature, over-current, and foreign object detection. Key features of the MWCT1200CFM include support for multi-coil topologies (enabling flexible positioning on the charging surface), an integrated digital demodulation engine that decodes Qi-compliant communication packets without an external ADC, built-in FSK/ASK modulation support, and adjustable output power up to 5 W. The device exposes an I²C interface for configuration and telemetry and includes an integrated gate driver for the external power stage. Technically, the MWCT1200CFM runs an embedded Qi state machine on an on-chip Cortex-M0 core, which decodes Qi protocol packets received through the coil sense path. The digital demodulation block performs amplitude-shift keying (ASK) decoding at typical Qi packet rates of 2 kbps and supports frequency-shift keying (FSK) reverse communication. The device also includes a proprietary foreign object detection algorithm that measures Q-factor changes before and during power transfer to identify metallic debris. Typical applications include 5 W single-coil charging pads, 5 W multi-coil free-positioning pads, Qi-compliant charging stands for mobile phones and wearables, and embedded charging modules in furniture or automotive center-console surfaces. The multi-coil support enables placement tolerance that is significantly wider than single-coil designs. When designing with this device, the engineer should follow NXP's reference design RDGDK1200 closely and route the differential coil-sense traces symmetrically. The PCB thermal pad must be soldered to a continuous ground pour to keep junction temperature within the -40 °C to +85 °C operating range during sustained 5 W power delivery. This page synthesizes distributor pricing, drop-in alternative availability, and practical design notes not found in the manufacturer datasheet alone.
NAU8214YG - 2.9W Mono Filter-Free Class-D Amp | Nuvoton
The Nuvoton NAU8214YG is a 2.9 W mono filter-free Class-D audio amplifier operating from a 2.5 V to 5.5 V supply, delivering 91% efficiency in a 20-pin QFN (4x4 mm) package. A Class-D audio amplifier is a switching amplifier that modulates the audio signal as high-frequency PWM pulses driving output MOSFETs; because the output devices are either fully on or fully off, power dissipation is far lower than in Class-AB designs. Within the amplifier hierarchy, the NAU8214YG sits as an audio amplifier IC within the broader linear amplifier and power management semiconductor family. Its filter-free (filterless) architecture drives a speaker directly without a low-pass LC output filter, saving board space and cost in compact designs. Key features include up to 2.9 W output power into a speaker load, a wide 2.5 V to 5.5 V supply range suitable for both Li-ion battery and USB 5 V rails, and power-supply rejection ratios up to 92 dB that suppress supply ripple. The device offers 91% efficiency, an enable/shutdown function, automatic mute/no-noise switching to eliminate pop and click, and built-in overvoltage protection. Quiescent current is a low 1.4 mA to 2.7 mA, extending battery life in portable products. Technically, the NAU8214 uses a mono Class-D modulation scheme in which internal feedback and filtering reconstruct clean audio even without an external LC filter, provided the speaker and wiring inductance fall within datasheet limits. Operating temperature spans -40C to +85C for industrial and portable use. Typical applications include portable speaker systems, smartphone and tablet audio outputs, Bluetooth speakers, and small industrial alarms where battery life and board area are critical. Design consideration: in filterless operation the switching waveform appears across the speaker leads, so keep speaker traces short and observe EMI radiated-emission limits; a small ferrite may be added if EMC testing requires it. This page synthesizes distributor pricing, verified datasheet parameters, and application guidance not consolidated in the manufacturer datasheet alone.
NAU8331DG - Class-D Boosted Audio Amplifier | Nuvoton
The Nuvoton NAU8331DG is a monophonic boosted Class-D audio amplifier with integrated high-efficiency Class-G boost converter and I/V (current/voltage) sense, enabling external speaker excursion control algorithms running on a host DSP or main processor. The device integrates a powerful Class-D amplifier stage with a boost converter so that a single lithium-ion battery input can deliver high output power to a small speaker while maintaining high efficiency. A boosted Class-D amplifier combines two power functions in one device: a switching boost converter that raises the battery voltage, and a Class-D output stage that drives the speaker from the boosted rail. This architecture is central to portable power management and audio subsystems, where battery voltage alone is insufficient to reach target acoustic output. Key features of the NAU8331 include the integrated Class-G boost converter for high efficiency, I/V sense feedback for speaker excursion and temperature protection when paired with DSP algorithms, and a digital/audio input interface for direct connection to application processors. According to the Nuvoton product brief, the V/I-Sense architecture is specifically designed to work with external speaker excursion control algorithms. Technically, the Class-G boost converter modulates the Class-D supply rail adaptively, reducing losses compared with fixed-rail boost designs. The I/V sense channels feed back speaker current and voltage so a DSP can model speaker cone excursion, coil temperature, and impedance in real time, enabling louder and safer audio from the same speaker. Typical applications are smartphone and tablet speakers, portable Bluetooth speakers, smart-home voice devices, and notebook PC audio, all of which demand maximum loudness from small batteries and small speakers. When designing with the NAU8331DG, plan the boost converter inductor and output filter per the manufacturer datasheet layout guidance, and confirm that the DSP excursion-control algorithm matches the I/V sense scaling of this device. This page synthesizes distributor pricing context, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.
NAU83P20YGB - 20W x2 Class-D Amp, PWM Input | Nuvoton
The Nuvoton NAU83P20YGB is a single-supply, 20W, high-efficiency Class-D audio power stage with a 2-channel PWM signal input interface, delivering 2 x 20W into 8-ohm loads (10% THD) from a VDD supply of 8V to 24V, housed in a 48-pin QFN (7x7 mm) package. A Class-D audio amplifier is a switching power amplifier that drives its output transistors fully on or off, so power dissipation is far lower than in Class-AB designs. Within the audio signal chain hierarchy, it sits at the power stage level: audio source, then DAC or PWM modulator, then Class-D power stage, then loudspeaker. The NAU83P20 family belongs to Nuvoton's smart-home-audio Class-D series of power management and audio semiconductors. Key features include a PWM input interface that accepts digital PWM signals directly from an audio processor, eliminating the analog input path and its associated noise; multiple output configurations, namely 2-channel bridged outputs (20W x 2), 4-channel single-ended outputs (10W x 4), and 2-channel single-ended plus 1-channel bridged; typical power efficiency around 90%; and a typical signal-to-noise ratio of 105dB, which preserves dynamic range in quiet listening environments. Technical depth: the device integrates under-voltage detection, over-current detection and over-temperature detection, protecting the power stage against fault conditions such as output short circuits, brown-out events and thermal overload. Because the input is PWM, the IC acts as a power-stage gate driver and H-bridge, so EMI and switching behavior are largely determined by the upstream modulator and the output LC filter. The single-supply architecture removes the need for negative rails or split supplies, simplifying power tree design. Typical applications include smart speakers and smart-home audio products, television and monitor internal speakers, and portable or powered speaker systems where a single 8V-24V supply such as a 12V or 19V adapter rail is available. The 105dB SNR suits high-quality music playback, while the multi-configurable outputs allow one IC to serve 2.0, 2.1, or 4.0-channel systems. Design consideration: budget the output LC filter and PCB thermal copper carefully - at 90% efficiency, 2 x 20W output implies roughly 4-5W of heat dissipation, so the exposed pad of the 48-QFN must be soldered to a solid ground plane with thermal vias. This page synthesizes distributor availability data, Nuvoton documentation links, protection-feature details and practical design notes not consolidated on the manufacturer page.
NBM2317S60D1580T0R - 800W Non-Isolated Bus Converter 48V-to-12V | Vicor
The Vicor NBM2317S60D1580T0R is a high-efficiency non-isolated, fixed-ratio bidirectional bus converter operating from a 40 to 60 VDC high-side voltage bus to deliver a ratiometric low-side voltage from 10 to 15 VDC, with a continuous output power rating of 800 W and 97.9% peak efficiency. A bus converter (BCM, bus converter module) is a specialized DC-DC converter that uses a fixed turn ratio (rather than closed-loop PWM duty-cycle regulation) to step a high-voltage distribution bus down to a lower intermediate voltage, then feeds downstream point-of-load regulators. In modern 48 V data center, telecom, and industrial architectures, bus converters bridge a 48 V backbone to legacy 12 V loads, replacing bulky isolated converters with smaller, faster, higher-density non-isolated stages. NBM (non-isolated bus converter) modules specifically omit galvanic isolation when the application architecture already provides it elsewhere, maximizing power density and transient response. Key features of the NBM2317S60D1580T0R include a fixed K=1/4 conversion ratio (48 V nominal to 12 V nominal), 800 W continuous power capability, peak efficiency of 97.9%, and a low-noise switching topology that delivers fast transient response. The bidirectional capability allows current to flow in either direction between the high-side and low-side buses, supporting battery charging, energy storage, and dynamic load-sharing applications where power must move seamlessly between rails. The device uses Vicor's proprietary Sine Amplitude Converter (SAC) topology operating as a resonant zero-current-switching (ZCS) or zero-voltage-switching (ZVS) architecture, dramatically cutting switching losses and EMI relative to hard-switched PWM converters. The SM-ChiP (Surface Mount ChiP) package integrates magnetics, controls, and power semiconductors into a single low-profile surface-mount module, achieving power density exceeding 1000 W/in³ while maintaining junction temperatures well within industrial limits. Typical applications include 48 V-to-12 V intermediate bus conversion in servers and hyperscale data centers, AI accelerator and GPU power distribution, telecom equipment using -48 V battery plants, robotics and industrial 24/48 V bus systems, and bidirectional energy storage battery interfaces. When designing with the NBM2317S60D1580T0R, account for the fixed-ratio behavior: output voltage is determined entirely by input voltage, so downstream regulation must be handled by a downstream converter (such as a Vicor PRM or a point-of-load regulator). Provide adequate thermal management on the PCB to leverage the SM-ChiP package's top-side and bottom-side cooling paths. This page synthesizes real distributor pricing, verified drop-in alternatives within the Vicor NBM family, and practical design considerations not found in the manufacturer datasheet alone.
NBM2317S60D1580TMR - 1080W Non-Isolated Bus Converter | Vicor
The Vicor NBM2317S60D1580TMR is a high-efficiency non-isolated bus converter module designed to bridge 48V and 12V power-system domains. It operates from a 40V to 60V high-side input and delivers a ratiometric low-side output of 10V to 15V at up to 80A (1080W peak), with 97.9% peak efficiency. The SMD variant uses Vicor's 2317 Chameleon package with surface-mount termination for high-density PCB assembly. What is a non-isolated bus converter? A non-isolated bus converter (NIBC) is a fixed-ratio DC-DC converter used as a virtual supply rail in distributed power architectures. Unlike a switching regulator, an NIBC divides an existing high-voltage bus into a lower-voltage sub-rail using a capacitive energy-transfer topology. NIBC sits in the power-converter hierarchy as a category between point-of-load regulators and isolated DC-DC converters, providing high step-down ratios without transformer isolation. Key features of the NBM2317S60D1580TMR include a continuous 800W power rating, fixed 4:1 conversion ratio, 1.4 MHz switching frequency, parallelable operation for higher power, and bi-directional power flow capability. Typical conversion efficiency reaches 97.9% at nominal 48V/12V operation, reducing thermal losses compared to traditional buck converters at the same current rating. The NBM family from Vicor uses a proprietary Sinusoidal Amplitude Converter (SAC) topology combined with a zero-voltage, zero-current switching (ZVZCS) soft-switching architecture. This topology achieves high efficiency by eliminating switching losses and uses small ceramic bypass capacitors instead of bulky inductors or transformers. The result is a low-profile surface-mount module that fits between a 48V intermediate bus and downstream 12V point-of-load converters or direct loads. Typical applications include 12V intermediate bus generation in 48V telecom and data-center servers, AI accelerator and GPU auxiliary rails, high-current 12V distribution in industrial equipment, battery energy storage systems using 48V architecture, and bridging converters for automotive 48V mild-hybrid systems. When designing with this part, account for the fixed 4:1 conversion ratio: VOUT follows VIN/4 with a tolerance band. Use the module in conjunction with downstream buck or ZVS regulators for sub-ratios (5V, 3.3V, 1V). Provide adequate PCB copper beneath the surface-mount land pattern for thermal dissipation and high-current return paths. This page synthesizes distributor pricing, drop-in module equivalents, and paralleling notes not found in the manufacturer datasheet.
NBM2317S60E1560T0R - 800W Non-Isolated Bus Converter 60A | Vicor
The Vicor NBM2317S60E1560T0R is a 800 W Non-Isolated Bus Converter Module operating from a 38 V to 60 VDC high-side bus to deliver a ratiometric low-side voltage of 9.5 V to 15 VDC at up to 60 A continuous current, housed in a surface-mount ChiP (Chip-in-Plastic) package. It achieves 97.9% peak efficiency, up to 4.5 kW/in³ power density, and provides bidirectional start-up and steady-state operation with up to 1 kW, 2 ms peak power capability. A bus converter (also called a Bus Converter Module, BCM or NBM in Vicor nomenclature) is a fixed-ratio, non-isolated DC-DC converter that steps a higher distribution voltage down by a deterministic factor (in this case K=1/4 approx, 38-60V -> 9.5-15V) to power downstream point-of-load (PoL) regulators. Unlike a discrete buck regulator, the bus converter uses a Sine Amplitude Converter (SAC) topology with a proprietary zero-voltage-switching (ZVS) / zero-current-switching (ZCS) architecture, achieving high density and low noise. In a system hierarchy it sits above PoL regulators (DCM, PRM, PoL converters) and is part of the Factorized Power Architecture (FPA) ecosystem from Vicor. Key features include 60 A rated output current (step-down operation), 38-60 V high-side input range, a 9.5-15 V ratiometric low-side output, and 97.9% peak efficiency. The module provides low output impedance well beyond the bandwidth of most downstream PoL regulators, meaning input capacitance that would normally sit at the PoL input can be moved to the high-voltage side, reducing PCB area and BOM count. Technically, the NBM2317S60E1560T0R uses Vicor's proprietary SAC topology with a high-frequency soft-switching architecture achieving >97% efficiency at typical loads. The part is bidirectional, capable of start-up and steady-state operation in either direction when used with Vicor's PRM or BCM companion parts. Two cooling configurations are supported: two-sided cooling and bottom-side only (through-PCB) cooling, with thermal models provided for each. Typical applications include 48 V data center and telecom intermediate bus conversion, distributed power architectures for AI accelerators and GPUs, high-end computing motherboards, industrial 48 V robotics, and aerospace distributed power systems. The bidirectional capability makes it suitable for energy storage and battery systems as well. When designing with this device, ensure adequate PCB copper thermal mass or attach to a cold plate. Use Vicor's companion evaluation boards for thermal characterization and consult the datasheet for derating curves beyond the 60 A continuous rating. This page synthesizes distributor pricing, drop-in same-family alternatives, comparison data, and practical design guidance not assembled on any single manufacturer or distributor page.
NBM2317S60E1560T0R-VICOR - 800W Non-Isolated Bus Converter | Vicor
The Vicor NBM2317S60E1560T0R is a non-isolated, fixed-ratio DC-DC bus converter module (BCM) using Vicor's proprietary Sine Amplitude Converter (SAC) topology, delivering up to 800 W of continuous output power from a 38 V to 60 V input range to a ratiometric 13.5 V output at 60 A, in a surface-mount Chip (ChiP) package. It achieves a peak efficiency of 97.9 percent at moderate loading and supports bidirectional start-up and steady-state operation, enabling battery-source and bus-source flexibility. A bus converter module (BCM) is a fixed-ratio, non-isolated DC-DC converter that divides an intermediate bus voltage by a fixed K-factor (turns ratio equivalent) to produce a lower, regulated-feeling output. BCMs sit between an isolated front-end converter and downstream point-of-load (PoL) regulators, providing a low-impedance intermediate voltage rail with fast transient response and high efficiency. As fixed-ratio devices, BCMs cannot regulate output voltage independently of input voltage - regulation is achieved by the upstream front-end converter and downstream PoL stages, while the BCM provides the power transformation with minimal loss. Key features include a fixed K-factor of 1/4, a sinusoidal SAC switching waveform that minimises EMI and acoustic noise, low AC impedance beyond the bandwidth of typical PoL regulators, and up to 4.5 kW per cubic inch power density. The device supports up to 1 kW peak output for 2 ms transient events, an integrated thermal management footprint accepting either two-sided or bottom-side PCB cooling, and parallel operation capability for higher power rails. The ChiP surface-mount form factor eliminates through-hole magnetics and shrinks the converter footprint by an order of magnitude compared with discrete bus-converter designs. The NBM2317S60E1560T0R uses a zero-voltage switching (ZVS), zero-current switching (ZCS) Sine Amplitude Converter architecture operating at a fixed fundamental frequency in the megahertz range. The fixed K-factor of 1/4 means any input from 38 V to 60 V produces an output of 9.5 V to 15 V (Vin/4); the stated nominal output is 13.5 V at the typical 54 V nominal input. The bidirectional capability allows the same module to operate as a step-down or step-up converter, supporting battery charging and energy-storage applications without a second power path. Typical applications include 48 V telecommunications intermediate bus architectures, blade-server and high-performance compute power delivery, battery-backed 48 V infrastructure, industrial automation systems with 48 V or 54 V distribution, and high-current PoL rails where upstream isolation is handled separately. Designers commonly cascade this BCM with downstream PRM (pre-regulation) and VTM (voltage transformation) Vicor components, or with a family of point-of-load regulators from the same Vicor ecosystem. When designing with this device, ensure that input voltage remains within the 38 V to 60 V window under all line and load transients, and that the upstream source can absorb reflected ripple current from the BCM. The ChiP solder-pad layout is not compatible with hand-soldered or socketed assemblies - it requires a reflow profile aligned with the J-STD-020 MSL rating for the part. This page synthesises distributor pricing, drop-in same-family alternatives, and practical thermal-layout notes that are not gathered in any single manufacturer datasheet, giving engineers a faster path to a verified BOM decision.
NCL2801CDADR2G - High-Efficiency CrM Boost PFC Controller
The onsemi NCL2801CDADR2G is a high-efficiency current-mode critical-conduction-mode boost power-factor correction controller packaged in an 8-pin SOIC. It is designed for LED-lighting power supplies and other AC-DC boost PFC stages handling substantial bulk-capacitor ripple. Its headline features are current-mode CrM control, enhanced line-current total harmonic distortion performance, Valley Count Frequency Fold-back operation, and a 12.5 V start voltage. A power-factor controller is an integrated circuit that shapes input current drawn from an AC mains line so that current tracks voltage and the upstream system approaches unity power factor. In the broader hierarchy, the NCL2801 belongs to AC-DC power conversion, power management integrated circuits, and boost PFC controllers. Correct operation reduces reactive current, line-current distortion, and stress in upstream magnetic and capacitor components. The NCL2801 uses THD Enhancer technology to improve line-current total harmonic distortion across an extended operating range. It operates classically in Critical Conduction Mode at high loads. When load decreases, Valley Count Frequency Fold-back forces discontinuous conduction by introducing dead time corresponding to a fixed number of valleys, improving standby behavior while maintaining regulation. The 8-SOIC package supports compact offline-lighting designs. The controller is intended to drive PFC boost stages rather than directly switching the mains-connected power stage. A typical implementation combines the NCL2801 with a boost inductor, switching MOSFET, current-sense resistor, bridge rectifier, bulk capacitor, safety-rated components, and LED-driver downstream circuitry. The controller supplies control and protection functions, while the external power components determine available output power and conversion ratio. Typical applications include LED lamps and luminaires, electronic ballasts, compact offline LED power supplies, and cost-effective high-efficiency AC-DC front ends. The device is especially useful where low line-current THD, low standby power, and tolerance of high ripple on the bulk capacitor are important. Its lighting-focused feature set helps designers meet EMI and input-current-shape requirements without relying on a more complex digital controller. Design the feedback network and compensation for the actual boost converter, not as a generic voltage-regulator stage. Keep the current-sense loop short, isolate high-voltage switching nodes from sensitive control traces, and follow the manufacturer's application guidance for layout and component values. Review the datasheet limits before selecting the MOSFET, inductor, capacitor, and safety components. This page combines the verified manufacturer description, package and distributor information, application guidance, and engineering-oriented replacement limitations. It does not infer unprovided electrical limits or claim a pin-compatible replacement when the available cross-reference results do not establish one.
NCP1091DBG - PoE-PD 802.3af Interface Controller | onsemi
The onsemi NCP1091DBG is an integrated IEEE 802.3af Power over Ethernet Powered Device (PoE-PD) interface controller supporting up to 57V input voltage, 500mA supply current handling, and housed in an 8-pin TSSOP package. It is a member of onsemi's high-power HIPO PoE-PD family alongside the NCP1090 and NCP1092. A PoE-PD interface controller is the front-end circuit inside any powered device (such as an IP camera, wireless access point, or VoIP phone) that draws power over Ethernet cabling. Within the power-management hierarchy, it sits between the Ethernet magnetics/diode bridge and the downstream DC-DC converter, handling the detection, classification, and inrush-control handshake that IEEE 802.3af requires before full power is granted. Key features of the NCP1091 include the complete IEEE 802.3af signature functions: powered-device detection, classification, and under-voltage lockout (UVLO). It also provides programmable inrush and operational current limit, plus a power-good signal that guarantees clean enable and disable sequencing of the downstream DC-DC controller. The distinguishing feature versus the NCP1090 is its programmable under-voltage lockout threshold, letting designers tailor the brown-out point to their converter topology. Technically, the NCP1091 integrates a precision detection and classification front end with a pass-element control loop that limits inrush current during PSE capacitor charging, then transitions to operational current limiting during normal running. The power-good output only asserts when the PoE rail is valid, preventing premature startup of the isolated or non-isolated converter and protecting against IEEE-compliance violations. Typical applications include IP surveillance cameras, 802.3af-compliant wireless access points, VoIP and SIP desk phones, and any Ethernet-fed sensor or industrial endpoint that must present a valid PoE signature to the power-sourcing equipment. A key design consideration: verify the classification resistor setting and programmable UVLO divider against the maximum cable power budget, since the class advertised must match the load drawn after the DC-DC converter. This page synthesizes distributor availability data, family-level substitution analysis, and practical design notes not found in a single manufacturer datasheet.
NCP1093MNRG - IEEE 802.3at PoE-PD Interface Controller | onsemi
The onsemi NCP1093MNRG is an integrated IEEE 802.3at PoE-PD (Power over Ethernet Powered Device) interface controller in a 10-pin DFN (3x3 mm) exposed-pad package. It supports one channel of PoE detection and classification per IEEE 802.3af (PoE) and 802.3at (PoE+) over a 0 V to 57 V input range. A PoE-PD interface controller is the front-end power-management IC inside any Powered Device that draws power over Ethernet cabling. Within the power-management hierarchy it sits between the RJ45/data transformer pair and the isolated DC-DC converter: it performs thePowered Device half of signature detection, classification, inrush limiting, and operational current limiting that the Power Sourcing Equipment (PSE) in the switch or injector expects before it will fully enable power on the cable. Key features of the NCP1093 include integrated detection and classification meeting IEEE 802.3at Type 2, under-voltage lockout (UVLO), controlled inrush and operational current limiting to protect the internal pass path, and dedicated power good and NCLASS_AT status signals that guarantee proper sequencing of the downstream converter. The part is specified for industrial temperature grade operation, which broadens its use beyond office networking equipment. Architecturally, the NCP1093 belongs to onsemi HIPO high-power PoE-PD family (NCP1093/NCP1094), which integrates all required PD interface functions into a compact 10-pin footprint. Integration of the pass-element control and classification logic reduces bill-of-material count versus discrete detection/classification circuits, and the exposed-pad DFN provides low thermal resistance for the internal MOSFET drive path. The device operates with a very low control-side current (approximately 5 mA class of control consumption per distributor specification tables) to keep the PD signature within standard limits during detection. Typical applications include PoE+ IP surveillance cameras, IEEE 802.11ac wireless access points, VoIP telephones, PoE LED lighting luminaires, and industrial network edge devices that must be powered directly from the Ethernet cable. In each case the NCP1093 interfaces the PSE to the isolated flyforward or flyback converter that generates the system low-voltage rails. A key design consideration: onsemi has officially marked the NCP1093MNRG as end-of-life (EOL), with a last order date of 1 March 2024 and last ship date of 31 December 2024. The recommended follow-on is the NCP1081 family, which comes in a different package, so new designs must not start with this part. Existing designs should plan a footprint change or secure last-time-buy stock. This page synthesizes distributor pricing, EOL status details, drop-in alternative scarcity analysis, and practical design notes not found in the manufacturer datasheet alone.
NCP1294 - Fixed Frequency PWM Controller for Flyback/Forward/Boost | onsemi
The onsemi NCP1294 is a fixed frequency, feed forward voltage mode PWM controller optimized for high frequency primary side control in Flyback, Forward, or Boost converter topologies. It integrates a complete set of control features including soft start, accurate duty cycle limit, less than 50 uA startup current, and dedicated over and under voltage protection. The device operates from a VCC supply commonly fed via an auxiliary winding, and it drives an external MOSFET through a totem pole output stage sized for direct gate drive in low to medium power converters. A PWM controller is a building block inside switched mode power supplies (SMPS) that produces a fixed frequency clock and modulates its duty cycle to regulate the converter output voltage. In the hierarchy of power management ICs, the NCP1294 sits as a current mode/peak control sub-family member: PWM controller -> SMPS controller -> DC-DC controller -> power management IC -> semiconductor. Its feed forward voltage mode architecture adds line-voltage feed forward to reject input voltage transients faster than a conventional voltage mode controller can respond through its error amplifier loop alone. Key features include programmable maximum duty cycle clamp, cycle-by-cycle current limit, internal soft start, undervoltage lockout, overvoltage protection, and a low startup current below 50 uA which simplifies self bias designs from the input bulk rail. The controller typically operates at switching frequencies programmable up to the audio band and beyond, enabling smaller magnetics in isolated telecom and industrial auxiliary supplies. The architecture uses a leading edge blanking interval to mask the leading edge current spike caused by the MOSFET turn on transient, improving noise immunity at the current sense input. Internally the oscillator is trimmed and the reference is bandgap based for stable operation over temperature, supporting industrial operating ranges typical of -40C to +125C. The combined UVLO and OVP set the input supply window for the IC itself, simplifying the housekeeping design on the primary side. Typical applications for the NCP1294 include isolated telecom auxiliary supplies such as 48 V to low voltage DC-DC bricks, industrial DIN rail and process control power modules, AC-DC adapters up to several hundred watts using forward or flyback topologies, and standby/auxiliary rails in server and PoE powered systems. Its configuration flexibility also suits it for boost derived front end PFC auxiliary rails and small solar micro inverter auxiliary supplies. When designing with the NCP1294, pay close attention to current sense resistor placement and to the CS pin filter network, because the leading edge blanking only masks the first few hundred nanoseconds of the turn on spike; longer ringing from a poor layout will inject false current limit triggers. Use a small RC on the CS pin and keep the sense loop area minimal. This page consolidates onsemi datasheet parameters, distributor stock pricing, and same-package drop-in alternatives such as the NCP1294C and NCP1284 into a single engineering reference so that sourcing, replacement, and design decisions can be made without cross referencing multiple distributor and manufacturer PDFs.
NCP1294DB - Fixed-Frequency PWM Controller | onsemi
The onsemi NCP1294DB is a fixed-frequency, feed-forward, voltage-mode PWM controller optimized for high-frequency primary-side control. It supports basic flyback, boost, and forward-converter topologies, operates from the DC input rail supplying the primary circuit, and is packaged for surface-mount assembly. The verified manufacturer material specifically identifies soft-start, accurate duty-cycle limiting, less than 50 uA startup current, overvoltage and undervoltage protection, and current-mode operation as key features. A PWM controller is a semiconductor timing and regulation device used in switched-mode power supplies. Its oscillator establishes the switching frequency, while its control loop compares a feedback signal with an internal reference and adjusts the gate-drive command. The NCP1294DB belongs to the DC-DC power-conversion controller category and is intended for isolated flyback or forward designs as well as non-isolated boost arrangements. Feed-forward voltage-mode control is especially relevant to offline power-conversion systems where predictable duty-cycle behavior and primary-side regulation are important. The controller’s fixed-frequency architecture simplifies compensation planning because the nominal switching point does not vary with input voltage. Soft-start helps limit inrush stress during power-up, while accurate duty-cycle limiting constrains the maximum commanded on-time. The low startup current is intended to reduce the burden on the startup path before the auxiliary supply becomes operational. Overvoltage and undervoltage protection provide additional system safeguards, although exact thresholds, tolerances, response timing, and restart behavior must be taken directly from the manufacturer datasheet. The NCP1294 is designed for high-frequency primary-side control, making it relevant to compact AC/DC adapters, offline power supplies, forward converters, boost converters, and industrial control systems. In an isolated flyback design, the controller drives a primary MOSFET while an optocoupler or other isolation mechanism communicates output-voltage information. In a forward converter, transformer reset and duty-cycle constraints determine the practical power level. In a boost design, the same controller family supports a non-isolated conversion stage when its voltage and timing limits are satisfied. Designers should use the datasheet’s recommended oscillator, compensation, current-sense, startup, and gate-drive networks rather than treating generic PWM-controller layouts as directly interchangeable. Transformer reset time, propagation delay, MOSFET switching speed, output-capacitor ESR, feedback bandwidth, and safety spacing all affect practical performance. NCP1294DB is a controller, not a complete power stage; an external MOSFET, magnetics, rectifier, feedback network, and protection components remain necessary. This page summarizes the verified NCP1294DB architecture, application fit, and design considerations while distinguishing documented features from parameters that were not supplied in the retrieved source text. For sourcing, confirmation of current lifecycle and exact package-related ordering details should be completed before committing a production design.
NCP1399APDR2G - 600V Half-Bridge Resonant Controller | onsemi
The onsemi NCP1399APDR2G is a high-performance current mode controller for half-bridge resonant converters, integrating two 600 V gate drivers in a 16-pin SOIC package. It supports a wide switching frequency range of 20 kHz to 750 kHz, adaptive dead-time control, and a dedicated PFC front-stage interface, making it well-suited for high-efficiency LLC and other resonant converter topologies. An LLC resonant controller is a specialized power-supply control IC that drives a half-bridge switching stage whose switches feed an LC resonant tank. The tank shapes the current waveform so the MOSFETs switch at zero voltage (ZVS), eliminating switching losses and enabling high-frequency, high-density designs. Controllers such as the NCP1399APDR2G sit within the power-management IC family and are commonly deployed as the secondary-side controller after a PFC front end in TV power supplies, server PSUs, and industrial SMPS modules. Key features of the NCP1399APDR2G include integrated 600 V half-bridge gate drivers that simplify PCB layout and reduce the bill of materials, an adjustable minimum switching frequency with precise dead-time generation, dedicated PFC control output for coordinated front-stage operation, brown-out protection on the high-voltage bulk rail, and comprehensive fault protection (overcurrent, overtemperature, overload, and brown-out). According to the onsemi NCP1399 datasheet, the device also features a skip-mode function for light-load efficiency improvement. Architecturally, the NCP1399APDR2G uses a current-mode control loop with a dedicated feedback input, allowing tight regulation of the resonant tank current. The adaptive dead-time block automatically adjusts the dead time between the high-side and low-side gate drive transitions to minimize body-diode conduction and maximize the ZVS range. The 600 V high-side driver is implemented using a level-shifter with an internal bootstrap clamp, removing the need for an external bootstrap diode in many designs. Typical applications include LCD TV power supplies (>150 W), notebook and laptop adapters, server and telecom SMPS modules, industrial LED drivers, and any high-density isolated DC-DC converter requiring ZVS operation above 100 W. The dedicated PFC output makes it an ideal match for designs requiring energy compliance such as 80 PLUS or ENERGY STAR. When designing with the NCP1399APDR2G, ensure the high-voltage bulk rail is decoupled with at least 1 µF X7R close to the Vbulk pin and follow the PCB layout guidelines for the high-side driver return path. The integrated 600 V drivers eliminate the need for an external gate-drive transformer, but the bootstrap capacitor must be sized correctly for the switching frequency and gate charge of the chosen MOSFETs. This page synthesizes distributor pricing, drop-in alternative recommendations, and practical design notes not found in the manufacturer datasheet alone.
NCP1654BD133R2G - 133 kHz CCM PFC Controller | onsemi
The onsemi NCP1654BD133R2G is a continuous-conduction-mode power factor correction controller with a nominal 133 kHz switching frequency in an 8-pin SOIC package. It is designed to control the power-switch conduction time in fixed-frequency PWM operation using instantaneous inductor-current feedback. The verified distributor listing specifies a 120 kHz to 146 kHz operating range. This controller belongs to the power-factor-correction and AC-DC power-conversion hierarchy, where it helps shape input current and reduce reactive power in boost pre-converter stages. A power factor correction controller is an integrated control IC that regulates the duty cycle and timing of a boost-converter power switch. In a CCM PFC stage, the inductor remains conducting during each switching cycle, and the controller adjusts switch timing from measured current to support near-unity power factor while transferring energy toward the DC output bus. The NCP1654 is intended for compact and robust continuous-conduction-mode step-up pre-converters. The main verified features of NCP1654BD133R2G are its CCM PFC architecture, fixed-frequency PWM operation, 133 kHz nominal switching frequency, 120 kHz to 146 kHz distributor-listed frequency range, and SOIC-8 package. The onsemi product page describes the family as minimizing external components and simplifying PFC implementation. The package and low component count can help reduce board area, but the final design still requires careful validation of inductor selection, current sensing, protection, startup behavior, and mains-side isolation. Its switching frequency affects magnetic-component size, control-loop behavior, switching losses, and electromagnetic-interference requirements. A 133 kHz nominal frequency is generally positioned above low-frequency boost operation for compactness and lower inductor size, but it does not eliminate the need for layout and thermal checks. The controller’s fixed-frequency operation should be compared with the power stage’s maximum switching stress and the inductor ripple-current target during design review. Typical applications include compact server and telecom power supplies, industrial AC-DC front ends, charger front ends, power adapters, and other boost PFC stages operating from rectified AC. The part is appropriate when the design needs a dedicated CCM PFC controller rather than a generic PWM regulator. Its external power switch and passive components must be selected for the actual input voltage, output voltage, output power, switching frequency, and thermal environment. For implementation, place the controller, current-sense network, gate-drive components, and power-stage connections according to the manufacturer datasheet layout guidance. Maintain short high-current switching loops, provide appropriate input and output decoupling, and verify creepage and clearance for the mains-connected front end. Do not treat the distributor frequency snippet as a substitute for the complete electrical limits; missing values should be confirmed in the manufacturer datasheet. This page combines the verified manufacturer description, distributor identity and package information, and practical selection guidance for engineers evaluating the NCP1654 family. It also distinguishes verified facts from parameters that still require datasheet confirmation, helping procurement and design teams make a more reliable decision for compact CCM PFC pre-converters.
NCP177AMX330TCG - 3.3V 500mA Fast Transient LDO | onsemi
onsemi NCP177AMX330TCG is a fixed 3.3 V, 500 mA CMOS low-dropout linear voltage regulator with an enable function in a compact 4-pin XDFN 1 x 1 mm package. It operates from 1.6 V to 5.5 V and maintains output-voltage accuracy of 0.8% at 25°C. The part is designed for Li-ion battery-powered products and post-regulator applications requiring compact, efficient power conversion. A low-dropout regulator, or LDO, is a voltage regulator that passes input current through a pass element while controlling its voltage drop. The NCP177 belongs to the linear regulator and power-management IC hierarchy. Its low-dropout architecture preserves headroom in battery-operated systems, while the fixed 3.3 V output supports digital logic, sensors, wireless modules, and embedded microcontrollers without requiring an adjustable feedback network. The main differentiating feature is fast transient response, which helps the regulator respond quickly when load current changes. The device also supports an enable input for power sequencing and shutdown control. Its 4-pin XDFN package is intended for space-constrained portable electronics, while the 500 mA current capability covers a broad range of low-power embedded loads. The verified distributor data identifies the output as a single fixed positive regulator with 500 mA current capability. The NCP177 series is specified for an input range of 1.6 V through 5.5 V, making it appropriate for single-cell Li-ion systems and low-voltage rails derived from higher supplies. Its CMOS implementation and low-dropout behavior are useful when available battery headroom is limited. The onsemi product page identifies the device as a very low-dropout regulator with up to 0.5 A load-current capability and 0.8% accuracy at 25°C. Typical applications include battery-powered sensors, portable measurement equipment, wireless IoT endpoints, smartphone accessories, and compact consumer devices. An enable pin allows a system controller to connect or disconnect the regulated rail, reducing current consumption during standby. Designers should still verify capacitor stability, load transients, thermal conditions, and dropout margin against the exact operating environment. For PCB design, place the input, output, and enable connections according to the manufacturer land pattern, and use the manufacturer-recommended output capacitor near the output and ground pins. The onsemi datasheet specifically identifies a 1 µF ceramic X7R or X5R capacitor as suitable because of its low capacitance variation over temperature. Verify the final power dissipation at the maximum input-to-output voltage difference and load current before using the part in a thermally constrained design. This product page consolidates distributor availability, pricing context, verified NCP177 family capabilities, application guidance, and design considerations for engineers evaluating a compact fixed 3.3 V LDO.
NCP1835MN20R2 - 1A Single-Cell Li-Ion Charger | onsemi
onsemi NCP1835MN20R2 is an integrated linear lithium-ion battery charger with a maximum charge current of 1.0 A and a 4.2 V charge voltage, packaged in a 10-terminal 3 x 3 mm DFN with an exposed pad. It uses a constant-current, constant-voltage charging profile for one-cell Li-ion batteries and supports low-input-voltage operation. A linear lithium-ion charger is a power-management IC that converts source power into controlled battery charging energy. It belongs to the battery-management IC hierarchy, which supports portable electronics, mobile accessories, wearable devices, and compact battery-powered equipment. Unlike switching chargers, the NCP1835MN20R2 uses a simpler linear power path, making it useful where component count, control simplicity, and low board area matter. The charger provides adjustable charge current, regulation capability without a connected battery, and onboard thermal foldback. Its low-input-voltage capability is useful for USB-powered systems and compact adapters. The exposed-pad DFN package helps dissipate heat when charging, although thermal performance depends on PCB copper area and the selected charge current. According to the available manufacturer and distributor information, the NCP1835MN20R2 is identified as a 1 A maximum single-cell battery charger with a 4.2 V battery voltage and 10-DFN exposed-pad package. The ordering code includes the R2 tape-and-reel configuration, while the core electrical function remains a 1-cell Li-ion charger. Typical applications include USB-powered phones, portable audio equipment, wearables, small sensor nodes, and compact industrial or consumer products with a single Li-ion cell. When selecting it, verify the source voltage, battery chemistry, charge-current requirement, thermal conditions, and pinout against the latest onsemi datasheet before production release. For layout, place input and output capacitors close to the relevant pins and provide adequate exposed-pad copper for heat dissipation. Treat the listed distributor price as indicative and confirm current stock, lifecycle status, and authorized-channel availability before committing to a design.
NCP3063B - 1.5A Step-Up/Down/Inverting Switching Regulator | onsemi
The onsemi NCP3063B is a monolithic 1.5 A DC-DC switching regulator supporting step-up, step-down, and voltage-inverting topologies in a single IC. Housed in an 8-SOIC package, it integrates a temperature-compensated reference, a duty-cycle controlled oscillator with active current limit, a high-current output switch, and an internal thermal shutdown circuit. The device is a higher-frequency upgrade to the legacy MC34063A / MC33063A family. A switching regulator (sometimes called a SMPS controller or DC-DC converter IC) is a power management device that uses an internal power switch and an external inductor/capacitor network to efficiently convert one DC voltage to another. Switching regulators sit within the power management IC category, between linear regulators (which dissipate excess voltage as heat) and fully modular DC-DC converter modules. They are typically selected when efficiency, output current, or output voltage flexibility are paramount. The NCP3063 specifically targets low-cost step-up, step-down, and inverting converter implementations. The NCP3063B delivers 1.5 A peak switch current with an adjustable output voltage of 1.25 V and supports a wide operating voltage range suitable for single-cell to multi-cell battery inputs. It includes cycle-by-cycle current limiting, internal thermal shutdown, and a duty cycle controlled oscillator. The 8-SOIC surface-mount package provides a compact footprint with standard pin compatibility with the older MC34063A. Architecturally, the device uses a current-mode control loop with a 1.25 V internal reference and an external feedback divider. The oscillator frequency is set by a single timing capacitor, allowing designers to optimize efficiency versus component size. An internal comparator drives a Darlington output stage capable of sinking or sourcing up to 1.5 A peak. Cycle-by-cycle current limit is implemented by sensing the switch emitter voltage against an internal reference. Typical applications include cost-sensitive consumer products, battery-powered portable equipment, LED drivers, and auxiliary supplies in industrial systems. It is particularly attractive as a drop-in upgrade for legacy MC34063A designs where higher switching frequency allows smaller inductors and capacitors. The wide input tolerance also makes it suitable for automotive subsystems running off 12 V or 24 V rails. When designing with the NCP3063B, carefully size the inductor and flyback capacitor to maintain continuous conduction at the minimum load. The thermal pad of the 8-SOIC should be soldered to a copper pour for adequate heat dissipation at high switch currents. Always verify that the peak switch current does not exceed 1.5 A under worst-case conditions. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not found on a single distributor or manufacturer page, with all data points cited to either the onsemi datasheet (document NCP3063-D) or the listed data sources.
NCP3135MNTXG - 5A Sync Buck Converter 2.9-5.5V | onsemi
The onsemi NCP3135MNTXG is a fully integrated synchronous buck converter delivering up to 5 A continuous DC load current (6 A instantaneous) from a 2.9 V to 5.5 V input rail, housed in a 16-pin VFQFN exposed-pad (QFN-16 EP) package. It targets 3.3 V and 5 V step-down applications with an adjustable output from 0.6 V to 4.62 V and supports two control modes (FCCM and automatic CCM/DCM) for efficiency-versus-ripple tuning. Integrated high-side and low-side MOSFETs, internal compensation, and a power-good indicator minimize external component count and PCB area. A buck (step-down) DC-DC switching converter is a power management IC that efficiently converts a higher DC input voltage to a lower regulated DC output voltage by rapidly switching an internal MOSFET and smoothing the resulting pulsed waveform through an LC filter. Within the power management hierarchy, it sits above linear regulators (LDOs) in efficiency for large VIN/VOUT deltas but below multi-phase VRMs in current capability. Buck converters are the workhorse topology for distributing intermediate bus voltages (5 V, 3.3 V, 1.8 V, 1.2 V) across nearly every digital and mixed-signal system. The NCP3135MNTXG delivers 5 A continuous / 6 A peak output, operates from 2.9 V to 5.5 V VIN, and adjusts VOUT from 0.6 V to roughly VIN minus dropout. Its selectable FCCM (forced continuous conduction mode) ensures predictable noise/ripple regardless of load, while automatic CCM/DCM mode boosts light-load efficiency by skipping pulses. Internal MOSFETs (high-side + low-side) eliminate external FET selection, and built-in soft-start, power-good, and over-current/thermal protection reduce design risk. The 16-pin QFN exposed pad provides a low thermal resistance path, simplifying board-level thermal management. The architecture uses adaptive on-time (AOT) control with internal feedback compensation, enabling fast transient response without requiring external RC networks. The 5 V tolerant enable pin and power-good output simplify sequencing in multi-rail systems. By integrating both switches and compensation, the NCP3135 family targets designs where small PCB footprint, high efficiency, and minimal external BOM are critical. Typical applications include 5 V and 3.3 V point-of-load regulation in networking switches, FPGA/CPLD core and I/O rails, SSD controller power, set-top box and consumer SoC rails, and distributed bus converters in telecom/datacom cards. It is well suited wherever a single 5 V input must be stepped down to a lower logic rail with high efficiency and tight load regulation. When designing with this device, derate output current based on VIN/VOUT differential and ambient temperature. Ensure the exposed pad is soldered to a sufficient copper pour to keep junction temperature within the SOA. Select input/output ceramic capacitors with low ESR and adequate voltage derating; place the input cap as close as possible to the VIN and GND pins to minimize switching-node ringing. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that go beyond the manufacturer datasheet alone.
NCP3170BDR2G - 3A 18V Sync PWM Buck Converter SOIC-8 | onsemi
The onsemi NCP3170BDR2G is a 3 A synchronous PWM buck (step-down) DC-DC switching regulator operating from 4.5 V to 18 V input and producing adjustable outputs as low as 0.8 V in an 8-pin SOIC (0.154", 3.90 mm width) surface-mount package. It integrates the high-side and low-side MOSFETs to deliver up to 3 A continuous load current at switching frequencies up to 1 MHz, while providing cycle-by-cycle current-mode control for fast transient response and inherent line-voltage feed-forward. A buck (step-down) switching regulator is a type of DC-DC converter that efficiently steps a higher input voltage down to a lower output voltage by rapidly switching an internal power transistor and storing it in an external inductor. It belongs to the broader hierarchy of switched-mode power supplies (SMPS), which also includes boost, buck-boost, and SEPIC topologies. SMPS ICs in turn belong to the power management IC family used to generate stable, efficient rails for downstream analog and digital ICs. Key differentiating features include an internal 0.8 V ±2% reference, internal soft-start, power-good (PG) open-drain output, and internal compensation that minimizes external part count. The NCP3170 family (suffixes A and B) offers 3 A continuous output current, fixed-frequency PWM control for low noise, and a thermal-shutdown protection scheme. The B suffix (NCP3170B) is the 1 MHz switching-frequency option optimized for smaller inductors and capacitors. The architecture is a peak current-mode controller with internal synchronous rectification, eliminating the need for an external Schottky diode. The high-side P-MOSFET (upper switch) and low-side N-MOSFET (lower switch) are integrated, which reduces board area, lowers BOM cost, and improves efficiency at light loads. Cycle-by-cycle current sensing on the high-side MOSFET provides fast overcurrent protection and inherent input voltage feed-forward for good line transient rejection. Typical applications include point-of-load (POL) converters for FPGAs, ASICs, and DSPs, distributed 5 V/12 V bus regulation, networking and telecom card supplies, industrial control and factory-automation boards, and consumer set-top boxes. The 18 V input rating suits 12 V and 15 V rails common in distributed-power architectures. When designing with this part, select the external inductor using the datasheet's L = VOUT / (IOUT × fSW × ΔIL) guideline (e.g., approximately 4.7 µH at 5 VOUT, 1 MHz). Place input/output ceramic capacitors close to the IC and use a star-ground scheme; routing the exposed pad (when present) to a large ground copper pour improves thermal dissipation at full 3 A load. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
NCP3231AMNTXG - 25A Synchronous Buck Converter, 4.5-18V | onsemi
The onsemi NCP3231AMNTXG is a high-current, high-efficiency voltage-mode synchronous buck converter that operates from a 4.5 V to 18 V input rail and delivers output voltages as low as 0.6 V at up to 25 A continuous load current, packaged in a 40-pin VFQFN with exposed thermal pad. A buck converter (step-down DC-DC converter) is a switch-mode power supply topology that efficiently converts a higher DC input voltage to a lower DC output voltage by rapidly switching an inductor between charge and discharge phases. Within the broader taxonomy, the NCP3231AMNTXG belongs to the synchronous buck family (where a MOSFET replaces the conventional rectifier diode for higher efficiency), inside the voltage-mode PWM controller category, inside DC-DC switching regulators, inside the power management IC segment of integrated semiconductors. Key specifications include a 4.5 V to 18 V input range, adjustable output from 0.6 V up to roughly 5 V (limited by the 18 V maximum input minus headroom), 25 A continuous output current, and a high-side low-side integrated MOSFET pair that delivers high efficiency without external switches. The 40-pin VFQFN package with an exposed thermal pad supports sustained high-current operation by providing a low thermal-resistance path to PCB copper. The NCP3231A employs voltage-mode control with internal compensation, programmable switching frequency, soft-start, and comprehensive protection features including over-current, over-voltage, under-voltage lockout, and thermal shutdown. The synchronous rectification architecture eliminates the conduction loss of a freewheeling diode and pushes typical full-load efficiency above 90 percent at 12 V input to 1.2 V output, a level that conventional buck controllers cannot match without discrete synchronous FETs. Typical applications include server and telecom point-of-load converters, networking switch and router core rails, FPGA and ASIC power rails, industrial 12 V intermediate bus converters, and high-current distributed DC-DC POL modules. The 25 A capability is well suited to powering multi-core processors, DDR memory banks, and high-performance DSPs directly from a 12 V bus. When designing with this part, allocate substantial PCB copper area beneath the exposed pad to keep junction temperature within the safe operating area at 25 A, and follow the manufacturer's recommended input/output inductor and capacitor selection for the chosen switching frequency. Use the soft-start and enable pins to sequence multiple NCP3231AMNTXG rails in a multi-rail system. This page synthesizes distributor pricing, drop-in same-brand variants, and practical design notes that consolidate information normally scattered across the onsemi datasheet, distributor listings, and application notes.
NCP398FCCT1G - USB Type-C VCONN OVP IC, 5.65V OVLO | onsemi
The onsemi NCP398FCCT1G is a USB Type-C VCONN overvoltage protection (OVP) integrated circuit housed in a 4-ball WLCSP (0.84x0.84 mm) package. It features an overvoltage lockout (OVLO) threshold of 5.65 V and protects VCONN rails in USB Type-C ports against high-speed voltage transients that originate from the VBUS cable. The part is enabled through an active-low ENB (enable-bar) pin and integrates thermal shutdown protection for fault conditions. What is a VCONN OVP IC? A VCONN overvoltage protection IC is a specialized power-management device used in USB Type-C systems to safeguard the VCONN power rail that powers cable electronics (e-marked cables, retimers, and active cables). USB Type-C ports share connector pins between VBUS and the VCONN auxiliary supply, and a misconfigured cable or faulty adapter can inject the full VBUS voltage (5 V, 9 V, 15 V, or 20 V) onto the VCONN pin, instantly destroying the cable's electronic components. An OVP IC sits between the VCONN source and the cable, disconnecting the rail within microseconds whenever the detected voltage exceeds a safe threshold, typically an OVLO of 5.65 V for legacy cables or 3.65 V for modern USB PD 3.1 applications. Key features include a 5.65 V OVLO threshold, internal MOSFET switch with low on-resistance, fast overvoltage response time in the microsecond range, built-in thermal shutdown, and an active-low ENB pin for system-level control. The WLCSP-4 (0.84x0.84 mm) package occupies minimal board area and is well-suited for compact mobile and wearable designs where PCB real estate is at a premium. The integrated protection reduces external component count and BOM cost relative to discrete FET + driver solutions. The NCP398FCCT1G uses a back-to-back internal MOSFET topology that disconnects VCONN from the load during an overvoltage event while still allowing system-level monitoring through the OVLO logic. It is part of the onsemi NCP398 family, which is offered in UDFN and WLCSP packages to address different board layouts and thermal budgets. Typical applications include USB Type-C ports in smartphones, tablets, laptops, docking stations, and wall adapters where VCONN rails must be defended against cable-borne overvoltage transients. The 5.65 V OVLO makes the part targeted at legacy 5 V VCONN implementations; designs targeting USB PD 3.1 cables (which can carry 9 V, 15 V, or 20 V VBUS) often require a higher-threshold variant or an additional external protection stage. When designing with this device, place input/output capacitors adjacent to the WLCSP balls to minimize parasitic inductance, and follow IPC-7351 land pattern guidelines for wafer-level chip-scale packages to ensure reliable board-level reliability through thermal cycling and mechanical stress.