उत्पाद (44,000+)

MSP430F168IPM - 8MHz 16-Bit MCU | Texas Instruments
MSP430F168IPM

MSP430F168IPM - 8MHz 16-Bit MCU | Texas Instruments

The Texas Instruments MSP430F168IPM is an 8 MHz mixed-signal microcontroller with 48 KB Flash, 2 KB SRAM, a 12-bit ADC, dual 12-bit DAC, comparator, DMA, I2C, SPI, and UART in a 64-LQFP 10 x 10 mm package. It combines a 16-bit RISC CPU with integrated analog conversion and low-power operation for portable measurement, industrial control, and embedded instrumentation. A mixed-signal microcontroller is an MCU that combines digital processing with analog measurement or signal-generation functions. In the product hierarchy, the MSP430F168IPM is a 16-bit RISC microcontroller, a mixed-signal MCU, a semiconductor, and an embedded processing component. Its integrated ADC and DAC reduce the need for external conversion devices when a system must measure analog inputs and generate controlled analog outputs. Key features include an 8 MHz maximum clock, 48 KB of Flash program memory, 2 KB of SRAM, and a 125 ns instruction cycle time. The device also provides a 12-bit ADC, two 12-bit DAC channels, a comparator, DMA, and serial interfaces supporting I2C, SPI, and UART. These resources support efficient firmware execution, peripheral data movement, and compact mixed-signal designs without a separate analog front end. The MSP430 CPU uses 16-bit registers and a 16-bit RISC architecture. Its FLL+ frequency-locked-loop support, five low-power modes, and standby wake-up behavior below 6 microseconds make it suitable for systems that spend substantial time waiting for measurements while retaining fast response to new activity. The verified manufacturer product information identifies the family as optimized for extended battery life in portable measurement equipment. Typical applications include portable environmental monitoring, industrial process instrumentation, battery-powered sensor nodes, data loggers, and embedded control systems. A designer can use the ADC for sensor acquisition, DMA for moving conversion data without excessive CPU intervention, and the DAC for excitation or output control. I2C and SPI support digital sensors and external converters, while UART simplifies connection to host systems or service interfaces. The primary design consideration is firmware and resource planning. The MSP430F168IPM has 2 KB of SRAM, so sampled data should be processed and transferred efficiently rather than stored indefinitely. Decoupling, analog-ground layout, and ADC/DAC reference design must follow the manufacturer datasheet, while the 64-LQFP footprint requires careful escape routing and thermal-aware copper placement. This product record combines verified manufacturer and distributor specifications with practical mixed-signal design guidance, drop-in candidate analysis, a parameter comparison table, and application-focused selection advice. These engineering resources help buyers evaluate the MCU beyond basic catalog fields before requesting price, stock, or long-term supply information.

RFQ संपर्क
MSP430F169IPM - 16-Bit 8MHz Mixed-Signal MCU | Texas Instruments
MSP430F169IPM

MSP430F169IPM - 16-Bit 8MHz Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430F169IPM is an ultralow-power 16-bit mixed-signal microcontroller operating at 8 MHz, with 60 KB of Flash memory, 2 KB of SRAM, a 12-bit ADC, dual 12-bit DACs, and communication peripherals including I2C, SPI, and UART. It is packaged in a 64-pin LQFP measuring 10 mm by 10 mm. The MSP430F169 combines a 16-bit RISC CPU, 16-bit registers, five low-power modes, and extensive analog peripherals for portable measurement and embedded-control systems. A mixed-signal microcontroller integrates digital processing and analog functions in one device. In the MSP430 family, the MCU combines a low-power RISC core with timers, serial interfaces, direct-memory access, and on-chip analog conversion resources. This integration allows portable instruments to sample inputs, process measurements, control outputs, and communicate with external equipment while reducing component count and board space. Key features include an 8 MHz maximum clock frequency, 60 KB of Flash program memory, 2 KB of SRAM, a 12-bit ADC, two 12-bit DAC channels, and a comparator. The device also provides DMA, I2C, SPI, and UART interfaces. Its five low-power modes are intended to extend operating time in battery-powered applications, while the 16-bit architecture supports efficient handling of control and measurement tasks. The MSP430F169IPM is designed for embedded systems that need low power, analog measurement, and serial connectivity without requiring a larger external analog subsystem. The integrated ADC and DAC can be used for sensor acquisition, signal conditioning, reference generation, and output control. DMA can move data between peripherals and memory, helping reduce processor involvement in repetitive transfers. Typical applications include portable measurement instruments, battery-powered data loggers, industrial sensors, medical monitoring equipment, and compact control systems. For designs requiring several analog inputs and outputs, the dual DAC and 12-bit ADC provide useful resources. UART, I2C, and SPI interfaces allow connection to sensors, displays, memory, transceivers, and host processors. A key design consideration is firmware and power-mode planning. Engineers should select appropriate low-power modes, preserve required state between sleep intervals, and configure unused pins and peripherals to avoid unnecessary current draw. The 64-pin LQFP package also requires careful PCB layout and thermal management when the device operates continuously at higher clock frequencies. Verify the complete pinout, electrical limits, and peripheral configuration against the manufacturer datasheet before production release. This page combines manufacturer specifications, distributor availability, package details, and application-focused design guidance for engineers evaluating the MSP430F169IPM.

RFQ संपर्क
MSP430F2001IN - 16MHz MCU, 1KB Flash | Texas Instruments
MSP430F2001IN

MSP430F2001IN - 16MHz MCU, 1KB Flash | Texas Instruments

The Texas Instruments MSP430F2001IN is a 16-bit mixed-signal microcontroller with a 16 MHz maximum clock, 1 KB Flash memory, 128 B SRAM, timer resources, and a comparator, packaged in a 14-pin PDIP (N) package. Its combination of compact code and data memory, low-power operating modes, and integrated mixed-signal resources makes it suitable for small embedded control, sensing, and measurement designs. A microcontroller is a programmable integrated circuit containing a processor core, nonvolatile program memory, working RAM, and peripherals. The MSP430F2001 belongs to the MSP430 MCU family, whose RISC architecture is designed for low-power embedded control. Within the hierarchy of embedded semiconductors, the MSP430F2001IN is a microcontroller, mixed-signal processor, embedded processor, and system-on-chip device with timer and comparator functions. The most prominent specifications visible in the verified product information are its 16 MHz operating frequency, 1 KB Flash, 128 B SRAM, and 14-pin PDIP package. Its 16-bit RISC architecture supports efficient execution of compact control routines, while the on-chip timer supports periodic event generation and timing tasks. The integrated comparator allows threshold-based input decisions without requiring a separate comparator IC. Five power-saving modes, standby wake-up in less than 6 microseconds, and a 125 ns instruction-cycle time were also identified in the retrieved technical material. The limited 1 KB Flash and 128 B SRAM distinguish this device from larger MSP430 products. Firmware must therefore be compact, while RAM variables and interrupt-service routines require careful memory budgeting. This constraint is not a drawback for simple sensing and control nodes, but it makes the MSP430F2001IN less suitable for protocol-heavy gateways, graphical interfaces, large protocol stacks, or applications requiring extensive data buffering. Typical uses include battery-operated sensors, simple industrial measurement nodes, compact control panels, timer-based equipment, and low-power embedded systems. Designers can place the MCU between physical inputs and an actuator or communications interface, using the comparator for threshold detection and the timer for periodic measurement or control. Its small memory footprint can simplify firmware verification and make behavior easier to analyze than in a larger embedded platform. The principal design consideration is to confirm the complete operating voltage range, current consumption, peripheral assignment, and exact pin mapping in the manufacturer datasheet before layout or firmware release. The verified material confirms the 14-pin PDIP package but does not provide a complete pin table, so pin assignments should not be inferred from the package count. This page consolidates verified product facts, sourcing information, drop-in candidates, and practical selection guidance beyond a distributor listing. For new production designs, engineers should also evaluate MSP430 devices with more Flash or SRAM when future firmware growth is likely. For cost-sensitive, low-complexity products that fit within 1 KB Flash and 128 B SRAM, the MSP430F2001IN remains a compact mixed-signal MCU option with a documented 16 MHz clock and integrated timer and comparator resources.

RFQ संपर्क
MSP430F2001TN - 16MHz Ultra-Low-Power MCU | Texas Instruments
MSP430F2001TN

MSP430F2001TN - 16MHz Ultra-Low-Power MCU | Texas Instruments

The Texas Instruments MSP430F2001TN is an ultra-low-power mixed-signal microcontroller with a 16-bit RISC CPU, 16 MHz maximum clock rate, 1 KB of flash memory, and 128 B of SRAM in a 14-pin PDIP package. It combines a 16-bit timer, ten I/O pins, and an analog comparator, making it suitable for compact embedded control and sensor-oriented designs. A mixed-signal microcontroller is an embedded semiconductor that combines digital processing with analog functions. The MSP430 architecture belongs to the broader hierarchy of microcontrollers, embedded processors, and semiconductors. Its 16-bit RISC core uses a 125 ns instruction cycle, while the digitally controlled oscillator and FLL+ support flexible clock generation for energy-efficient operation. Low power is a defining feature of the MSP430F2001 family. Its supply-voltage range is 1.8 V to 3.6 V, active-mode current is 220 µA at 1 MHz and 2.2 V, standby current is 0.5 µA, and off-mode current with RAM retention is 0.1 µA. Five power-saving modes help reduce energy consumption when the application does not require continuous processing. The device provides a 16 MHz clock capability, a built-in 16-bit timer, ten I/O pins, and a versatile analog comparator. The comparator can support threshold detection and basic signal conditioning, while the timer supports periodic timing, counting, and event generation. The digitally controlled oscillator permits wake-up from low-power modes to active mode in less than 1 µs. Typical uses include battery-powered sensor nodes, compact industrial monitors, low-energy measurement instruments, appliance control modules, and embedded systems that periodically sample a sensor and return to a low-power state. Its small package and low active current are particularly useful where board space and average energy use are more important than maximum processing throughput. When designing around the MSP430F2001TN, account for the limited 1 KB flash and 128 B SRAM when sizing code, buffers, and state variables. Keep interrupt routines short, use a low-power operating mode during idle intervals, and verify comparator and timer behavior across the intended supply-voltage range. The manufacturer pin-description table should be used when assigning PCB signals and programming test points. This page combines the exact manufacturer and distributor product information with application guidance, power-mode considerations, and design notes that help engineers evaluate the MSP430F2001TN beyond a basic parameter list.

RFQ संपर्क
MSP430F2002IN - 16MHz 1KB Flash MCU | Texas Instruments
MSP430F2002IN

MSP430F2002IN - 16MHz 1KB Flash MCU | Texas Instruments

The Texas Instruments MSP430F2002IN is a 16-bit mixed-signal microcontroller rated at 16 MHz, with 1 KB of Flash memory, 128 bytes of SRAM, 10-bit SAR ADC, SPI/I2C USI, comparator, timer, and 10 I/O ports in a 14-pin PDIP package. According to the Texas Instruments product data, the device operates from 1.8 V to 3.6 V and is intended for industrial-temperature applications from -40°C to +85°C. A mixed-signal microcontroller combines a digital processing core with analog conversion and comparison functions. The MSP430F2002 belongs to the MSP430F2xx family of ultra-low-power 16-bit RISC microcontrollers, a branch of embedded processors and mixed-signal ICs. Its 125 ns instruction cycle provides a 16 MHz operating rate, while its small memory footprint targets compact control, sensing, and measurement systems rather than resource-intensive applications. Key device features include 1 KB of Flash program memory, 128 bytes of SRAM, a 10-bit successive-approximation ADC, a USI supporting SPI or I2C, an internal comparator, and timer resources. The 10 available I/O ports support integration with sensors, actuators, indicators, and external peripherals. The manufacturer data also identifies low supply-voltage operation, multiple low-power operating modes, and a wake-up time below 6 µs as important characteristics of the device family. The MSP430 architecture uses a 16-bit RISC core and a mixed-signal feature set suited to low-power embedded control. The ADC permits direct measurement of analog inputs, while the USI provides a compact interface to serial sensors and external controllers. Because SRAM is limited to 128 bytes, firmware must use the Flash program area efficiently and should avoid buffering large data sets in RAM. Typical uses include battery-powered environmental sensors, compact industrial monitoring nodes, digital thermometers, simple energy meters, low-cost control boards, and embedded instruments that require analog measurement, serial communication, and low standby consumption. The device can also support low-power wake-and-measure products where the ADC result determines whether communication should begin. Designers should verify the exact peripheral pin assignments and alternate-function limitations against the manufacturer datasheet before finalizing the PCB. The 14-pin PDIP package simplifies breadboard and through-hole prototypes, but its comparatively large footprint is less suitable for compact production products. Firmware should use conservative RAM budgets, retain only essential state between sleep intervals, and tolerate peripheral differences among MSP430F2xx family members.

RFQ संपर्क
MSP430F2002IPW - 16MHz 1KB Flash MCU | Texas Instruments
MSP430F2002IPW

MSP430F2002IPW - 16MHz 1KB Flash MCU | Texas Instruments

The Texas Instruments MSP430F2002IPW is an ultra-low-power, 16-bit mixed-signal microcontroller with a 16 MHz RISC core, 1 KB of Flash memory, 128 B of SRAM, and a 14-pin TSSOP package. It integrates ten I/O pins, a 10-bit ADC, an analog comparator, a 16-bit timer, and serial communications supporting SPI and I2C. A mixed-signal microcontroller is a semiconductor device that combines digital control logic with analog measurement or comparison functions. The MSP430 belongs to the broader hierarchy of embedded MCU, processor, and semiconductor products. Its architecture is designed for compact control systems in which low energy consumption, deterministic operation, and integrated sensing can reduce the number of external components. The principal benefits of the MSP430F2002IPW include its 16 MHz operating clock, 1 KB Flash program memory, 128 B SRAM, and five low-power operating modes. The 10-bit ADC supports embedded measurement without requiring a separate converter, while the comparator supports threshold detection and basic signal conditioning. SPI and I2C interfaces allow the controller to communicate with sensors, memories, transceivers, and other low-speed peripherals. The MSP430 uses a 16-bit RISC CPU with 16-bit registers, providing efficient execution for sensor acquisition, control loops, timing, and low-power state management. Five low-power modes are particularly valuable in battery-powered equipment because firmware can disable unused peripherals and place the MCU into a lower-energy state between measurement or communications events. Typical uses include portable measurement instruments, compact industrial sensors, low-power data loggers, battery-operated monitoring modules, and embedded control systems with analog inputs. Its integrated ADC, comparator, timer, and serial interfaces make it especially appropriate for designs in which board area and standby energy are more important than large program-memory capacity. When designing around this MCU, confirm that the application code, boot configuration, communication stack, and calibration data fit within the 1 KB Flash and 128 B SRAM limits. Use the manufacturer pin-description table when assigning PCB tracks, and follow the recommended decoupling and exposed-ground-layout guidance for the 14-pin TSSOP package. This page consolidates the device identity, memory and peripheral details, commercial information, same-family replacement options, comparison parameters, and practical PCB guidance into one engineering-focused reference for designers evaluating the MSP430F2002IPW.

RFQ संपर्क
MSP430F2002TN - 16MHz Mixed-Signal MCU | Texas Instruments
MSP430F2002TN

MSP430F2002TN - 16MHz Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430F2002TN is a 16 MHz mixed-signal microcontroller with 1 KB of Flash memory, 128 bytes of SRAM, SPI and I2C serial interfaces, a comparator, and timer resources in a 14-pin PDIP package. It is designed for compact embedded systems that need deterministic control, serial connectivity, and low power consumption within a small package footprint. A mixed-signal microcontroller is an embedded semiconductor that combines a digital microcontroller core with analog and timing peripherals. The MSP430 belongs to the MCU hierarchy of general-purpose embedded processors, where a 16-bit RISC core executes firmware while integrated converters, comparators, timers, and communication interfaces reduce the number of separate discrete components needed on a board. The device operates at up to 16 MHz and provides a 125 ns instruction cycle time. Its memory configuration includes 1 KB of Flash, described by distributor listings as 1K x 8 plus 256 bytes, together with 128 bytes of SRAM. The available peripherals include SPI, I2C, a comparator, and timer functions, allowing the MCU to interface with sensors, converters, displays, and other embedded-system peripherals. The MSP430F2002 supports a low supply-voltage range extending to 3.6 V, while distributor specifications also identify a 1.8 V to 3.6 V supply range. Its low-power design includes five power-saving modes, an off-mode RAM-retention current of 0.1 µA, and standby wake-up in less than 6 µs. These characteristics are relevant when the target equipment spends substantial time idle or operates from a constrained energy source. Typical uses include compact sensor nodes, industrial measurement modules, low-power instrumentation, simple motor or actuator controllers, and battery-operated embedded products. The 14-pin PDIP package also facilitates prototyping and through-hole assembly, while the SPI and I2C interfaces provide practical paths for connecting external sensors, memory, communication modules, and actuators. Designers should account for only 1 KB of Flash and 128 bytes of SRAM when sizing firmware and working memory. The small memory footprint favors compact control loops, boot code, and tightly bounded application logic rather than graphical interfaces or large protocol stacks. Supply voltage, timer requirements, and the availability of both SPI and I2C should be confirmed against the application before PCB design. This product record consolidates the verified manufacturer and distributor information into an engineer-oriented reference covering the 16 MHz performance, memory, mixed-signal peripherals, power characteristics, package constraints, sourcing considerations, and design trade-offs associated with the MSP430F2002TN.

RFQ संपर्क
MSP430F2003IN - 16MHz Sensing MCU with 16-Bit ADC | Texas Instruments
MSP430F2003IN

MSP430F2003IN - 16MHz Sensing MCU with 16-Bit ADC | Texas Instruments

The Texas Instruments MSP430F2003IN is a 16-MHz mixed-signal microcontroller with one 16-bit sigma-delta ADC, a Universal Serial Interface for SPI or I2C, 1 KB of Flash memory, 128 B of RAM, and a 14-pin PDIP package. It combines an MSP430 CPU16 core with energy-conscious sensing peripherals in a through-hole package suitable for prototyping and compact embedded control assemblies. A microcontroller is a programmable semiconductor that integrates a processor core, nonvolatile program memory, working memory, and peripherals on one die. The MSP430 belongs to the mixed-signal MCU hierarchy, combining digital control with analog measurement. Its 16-bit sigma-delta ADC supports acquisition of slowly changing or low-bandwidth sensor signals, while the USI provides a compact interface for external sensors, converters, and communication peripherals. The principal device characteristics are a 16-MHz operating frequency, one 16-bit sigma-delta ADC, 1 KB of Flash, 128 B of RAM, and USI support for SPI or I2C. The PDIP (N) package provides 14 accessible pins and eases hand soldering, automated through-hole insertion, and educational prototyping. The manufacturer product page describes the MSP430F2003 family as a 16-MHz sensing MCU intended for compact, low-power embedded systems. Technically, the MSP430F2003IN integrates a 16-bit RISC-like CPU16 processor with mixed-signal sensing resources. Its limited 1 KB Flash and 128 B RAM favor compact control programs rather than large application frameworks. Software must account for the small memory footprint, while the ADC and USI expand the available measurement and external-device connectivity without requiring separate interface ICs. Typical uses include battery-powered environmental monitoring, industrial sensor nodes, portable measurement instruments, and low-power control boards. The USI can connect an SPI or I2C sensor, while the 16-bit sigma-delta ADC is appropriate for precision-oriented analog acquisition. Firmware must preserve accurate timing and use the available RAM efficiently when buffering samples or maintaining application state. Designers should confirm ADC input range, channel availability, and the required external support circuitry against the manufacturer datasheet before finalizing analog front ends. The DIP outline also requires adequate board spacing and through-hole clearance. Although the part is simple to prototype, production designs should consider its small memory resources and package availability before committing to a new layout. This page consolidates verified manufacturer and distributor information, package details, pricing, comparison parameters, and practical design guidance. It is intended to accelerate component selection while clearly identifying which engineering details remain tied to the official MSP430F20x1, MSP430F20x2, and MSP430F20x3 datasheet.

RFQ संपर्क
MSP430F2003TN - 16MHz 16-Bit Sensing MCU | Texas Instruments
MSP430F2003TN

MSP430F2003TN - 16MHz 16-Bit Sensing MCU | Texas Instruments

Texas Instruments MSP430F2003TN is a 16 MHz, 16-bit ultra-low-power mixed-signal microcontroller with a 16-bit sigma-delta ADC, USI communication interface, 1 KB Flash memory, and 128 bytes of RAM in a 14-pin DIP package. The MSP430F2003 combines a 16-bit RISC CPU, ten I/O pins, and low-power operating modes for compact portable measurement systems. A mixed-signal microcontroller is an embedded processing device that combines a digital CPU and digital peripherals with analog measurement functions. The MSP430F2003 belongs to the hierarchy of mixed-signal MCU > microcontroller > embedded processor > semiconductor. Its sigma-delta ADC is designed for low-speed or high-resolution measurement, while the Universal Serial Interface supports synchronous SPI or I2C communication with external sensors, converters, and memory devices. The principal features of this device are its 16 MHz maximum clock rate, 16-bit CPU architecture, 16-bit sigma-delta ADC, USI peripheral, 1 KB Flash memory, 128 bytes of RAM, and ten I/O pins. According to the Texas Instruments MSP430F2003 product information and manufacturer datasheet, the device is intended for portable measurement applications where low power, compact packaging, and integrated analog acquisition are more important than large program memory or high peripheral bandwidth. The MSP430 architecture uses 16-bit registers and a RISC instruction set to provide deterministic control for embedded sensing. The USI can operate with SPI or I2C protocols, allowing the MSP430F2003TN to communicate with external sensors without requiring a separate serial transceiver. Five low-power modes are identified in the manufacturer product information, helping software reduce current consumption when the acquisition and communication functions are not continuously active. Typical applications include portable environmental monitors, low-cost industrial sensing nodes, battery-powered data loggers, connected measurement instruments, and compact control products that need an ADC plus a serial sensor interface. The 1 KB Flash and 128 bytes of RAM make the device most appropriate for focused embedded tasks rather than complex user interfaces, extensive data storage, or high-throughput signal processing. The principal design consideration is memory planning. Firmware, calibration values, configuration data, stack requirements, and communication buffers must fit within the available 1 KB Flash and 128 bytes of RAM. Designers should also follow the electrical limits, oscillator requirements, clock configuration, and decoupling recommendations in the manufacturer datasheet rather than assuming that a functionally similar MCU can replace it without review. This product page consolidates the verified 16 MHz, 16-bit ADC, USI, Flash, RAM, package, pricing, and sourcing information while adding application guidance, selection criteria, and design notes. It also distinguishes direct device attributes from parameters that still require confirmation from the full Texas Instruments datasheet, avoiding unsupported assumptions about electrical ratings or lifecycle conditions.

RFQ संपर्क
MSP430F2011IN - 16MHz 16-Bit Ultra-Low-Power MCU | Texas Instruments
MSP430F2011IN

MSP430F2011IN - 16MHz 16-Bit Ultra-Low-Power MCU | Texas Instruments

Texas Instruments MSP430F2011IN is a 16-bit ultra-low-power mixed-signal microcontroller with a 16 MHz maximum clock, 2 KB of Flash memory, and 128 bytes of SRAM in a 14-PDIP package. Its operating supply-voltage range is 1.8 V to 3.6 V, while its key power figures include 220 µA active current at 1 MHz and 2.2 V, 0.5 µA standby current, and 0.1 µA off-mode current with RAM retention. A microcontroller is a programmable system-on-chip containing a processor core, nonvolatile program memory, working memory, and peripherals that acquire or control external signals. The MSP430 family follows the hierarchy MCU → embedded microcontroller → mixed-signal microcontroller → semiconductor. Its 16-bit RISC architecture uses 16-bit registers and a constant-memory instruction set optimized for compact control firmware. Five low-power modes and fast standby wake-up make this device especially appropriate for portable, battery-powered measurement systems. The MSP430F2011IN provides integrated timing and analog-comparison resources, including timer functions and a comparator, while its scan interface supports background capture of selected internal signals. The FLL+ frequency-locked loop and maximum 16 MHz operating frequency provide useful processing headroom for sensor acquisition, timing, state-machine control, and low-rate communication. Five power-saving modes allow firmware to reduce energy consumption when continuous CPU execution is unnecessary. The device supports an ultra-low supply-voltage range of 1.8 V to 3.6 V. Its 16-bit RISC core executes instructions with a stated 125 ns instruction-cycle time at the maximum clock frequency. Active-mode current is specified as 220 µA at 1 MHz and 2.2 V, demonstrating that performance can be scaled by clock and operating-state requirements rather than operating continuously at the maximum frequency. Typical uses include portable multimeters, environmental sensors, industrial measurement instruments, battery-powered data loggers, and compact embedded control products. The combination of 2 KB Flash, 128 bytes of SRAM, integrated comparator functions, and standby current of 0.5 µA suits designs that periodically wake, measure, process, and return to a low-power state. Designers should verify startup behavior, pin multiplexing, and application-specific peripheral assignments against the manufacturer datasheet before final PCB release. Because the IN orderable uses a 14-pin through-hole package, breadboarding and hand assembly are straightforward, but its larger footprint is less compact than an equivalent surface-mount implementation. This page combines verified manufacturer and distributor information, practical power-management guidance, package constraints, and same-family replacement context. It also separates published facts from data that still requires device-specific verification, helping engineers plan a qualified MSP430F2011IN design without relying on unverified equivalent parts.

RFQ संपर्क
MSP430F2011TN - 16MHz 16-Bit MCU | Texas Instruments | Embedded
MSP430F2011TN

MSP430F2011TN - 16MHz 16-Bit MCU | Texas Instruments | Embedded

The Texas Instruments MSP430F2011TN is a 16-bit mixed-signal microcontroller with a 16 MHz CPU, 2 KB of Flash memory, 128 bytes of SRAM, timer resources, and a comparator in a 14-pin PDIP package. It belongs to the MSP430 ultra-low-power microcontroller family, combining a mixed-signal MCU architecture with integrated comparison capability for compact embedded control systems. A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. In the MSP430 family, the 16-bit RISC core is optimized for low-power embedded control, while integrated timers and comparators reduce the need for external components. The MSP430F2011TN therefore sits within the hierarchy of microcontroller, embedded processor, mixed-signal MCU, and semiconductor. The primary verified specifications are a 16 MHz operating frequency, 2 KB of Flash, and 128 bytes of SRAM. The device also includes a timer and comparator, according to the Texas Instruments product page. Its 14-pin PDIP package is intended for conventional through-hole PCB assembly, prototyping, and legacy or industrial control designs where a leaded package simplifies inspection and manual servicing. The MSP430F2011TN uses a 16-bit CPU architecture and combines digital control with analog comparison functions. Although the verified distributor snippet also describes a 2K × 8 organization plus 256 bytes of Flash, the official product summary identifies 2 KB of Flash and 128 bytes of SRAM; engineers should therefore confirm the exact memory map in the manufacturer datasheet before allocating program or data space. Typical uses include low-power sensor nodes, simple control panels, battery-operated instruments, comparator-based threshold circuits, and compact industrial controllers. The comparator can monitor an analog input locally, while the timer supports periodic measurement, timing, or control functions. The 14-pin package is especially suitable where a small through-hole controller is preferred over a fine-pitch surface-mount device. When designing around this MCU, verify the oscillator, reset, I/O, comparator-input, and supply-pin assignments against the exact package drawing before laying out the PCB. Program and data budgets must also be checked because only 2 KB of Flash and 128 bytes of SRAM are available in the verified product summary. Decoupling, reset behavior, and unused-pin handling should follow the manufacturer’s hardware guidelines. This page consolidates verified manufacturer and distributor information, orderable MPN details, price context, drop-in alternatives, and practical selection guidance. It is designed to help engineers identify whether the MSP430F2011TN is suitable for a new embedded design or as a controlled replacement within the 14-pin PDIP MSP430F2011 family.

RFQ संपर्क
MSP430F2012IN - 16MHz 2KB Flash 128B SRAM MCU | Texas Instruments
MSP430F2012IN

MSP430F2012IN - 16MHz 2KB Flash 128B SRAM MCU | Texas Instruments

The Texas Instruments MSP430F2012IN is a 16 MHz mixed-signal ultra-low-power microcontroller with 2 KB of Flash memory, 128 B of SRAM, a 10-bit ADC, timer, I2C, and SPI, supplied in a 14-pin PDIP package. It belongs to the MSP430F2xx family of 16-bit RISC microcontrollers designed for low-power embedded measurement, control, and sensor-node applications. The MSP430 architecture is a mixed-signal MCU family in which the CPU, analog conversion, timers, communication peripherals, and low-power modes are integrated for compact instrumented systems. The 16-bit CPU supports efficient interrupt-driven control and deterministic timing, while the integrated 10-bit ADC reduces the need for external analog front-end components in battery-powered measurement designs. Key features of the MSP430F2012IN include a 16 MHz maximum clock rate, 2 KB program Flash, 128 B SRAM, a 10-bit ADC, timer resources, I2C, and SPI. The 14-pin PDIP package is suited to through-hole prototyping, legacy industrial controllers, and designs where a socketed or hand-soldered microcontroller package is more practical than a surface-mount alternative. The MSP430F2012IN is intended for applications such as low-cost sensor nodes, industrial measurement modules, portable instruments, simple motor and actuator controllers, battery-powered monitors, and compact embedded control boards. Its small memory footprint makes firmware design and code size important considerations, while the mixed-signal peripherals simplify designs that require measurement and serial communication. A key design consideration is that the MSP430F2012IN is a small-footprint MCU with limited RAM and Flash. Applications should keep working buffers small, use efficient interrupt routines, and avoid relying on libraries that require substantial memory. A decoupling capacitor should be placed close to the supply pins, and unused inputs should be configured appropriately. This product page combines the verified 16 MHz, 2 KB Flash, 128 B SRAM, 10-bit ADC, timer, I2C, SPI, and 14-pin PDIP information with procurement, comparison, and engineering guidance. It is intended to help engineers confirm fit, plan firmware constraints, and evaluate supply-chain options before designing a new board.

RFQ संपर्क
MSP430F2012IPW - 16MHz Ultra-Low-Power MCU | Texas Instruments
MSP430F2012IPW

MSP430F2012IPW - 16MHz Ultra-Low-Power MCU | Texas Instruments

The Texas Instruments MSP430F2012IPW is an ultra-low-power mixed-signal microcontroller with a 16 MHz MSP430 16-bit RISC core, 2 KB of Flash memory, 128 bytes of SRAM, and a 10-bit ADC in a 14-pin TSSOP (PW) package. It combines a 125 ns instruction cycle with five power-saving modes, making it suitable for compact, battery-operated measurement and control systems. A mixed-signal microcontroller is a semiconductor device that combines a programmable processor with analog measurement functions. Within the broader hierarchy of embedded processors, the MSP430F2012 belongs to the low-power MCU family and integrates CPU, memory, ADC, timers, and serial interfaces. This integration reduces board area and simplifies designs that require periodic sensing, control updates, and low standby consumption rather than continuous high-performance processing. The MSP430F2012IPW operates at up to 16 MHz and provides 2 KB Flash plus 128 bytes of SRAM. Its 10-bit ADC supports embedded analog measurements, while the listed timer, I2C, and SPI resources support sensor acquisition, event timing, and external peripheral communication. The industrial ordering option supports a -40°C to 85°C temperature range, making the device appropriate for temperature-varying industrial equipment when the complete circuit also meets its environmental requirements. The MSP430 architecture uses a 16-bit RISC processor with 16-bit registers and constant generators, supporting efficient code execution in a compact memory budget. A frequency-locked loop supports controlled clock operation, while the ability to wake from standby in less than 6 µs helps the MCU alternate between short active measurement periods and low-power intervals. These characteristics are particularly valuable when standby energy dominates the operating profile. Typical uses include battery-powered sensor nodes, industrial process transmitters, compact energy meters, portable measurement instruments, and low-duty-cycle control boards. I2C and SPI permit connection with sensors and memory, while the ADC handles analog inputs from resistive dividers, thermistors, and external sensing circuits. Firmware should use timer-driven wake events rather than continuous polling to realize the intended low-power benefit. Designers should budget the ADC reference, input impedance, acquisition time, and signal conditioning according to the datasheet. Decoupling capacitors should be placed close to the supply pins, and unused inputs should be connected according to the device recommendations. Software must also verify clock selection, wake conditions, and flash endurance before establishing a field update policy. This page combines the manufacturer’s core MCU specifications, package and ordering information, pricing evidence, drop-in alternatives, comparison parameters, and practical design guidance. It also distinguishes confirmed functions from parameters that require an engineering review, helping engineers evaluate the MSP430F2012IPW for embedded control and low-power sensing designs.

RFQ संपर्क
MSP430F2012TN - 16MHz, 2KB Flash Mixed-Signal MCU | TI
MSP430F2012TN

MSP430F2012TN - 16MHz, 2KB Flash Mixed-Signal MCU | TI

The Texas Instruments MSP430F2012TN is a 16-bit mixed-signal microcontroller with a 16 MHz MSP430 CPU, 2 KB Flash memory, 128 B SRAM, a 10-bit ADC, timer, I2C, and SPI in a 14-pin PDIP package. Its compact architecture combines a 16-bit RISC core with mixed-signal peripherals for low-power embedded control, sensor measurement, and compact communication designs. A microcontroller is a programmable system-on-chip that integrates a processor core, memory, and peripherals such as analog converters, timers, and serial interfaces. Within the product hierarchy, the MSP430F2012TN is an ultra-low-power mixed-signal microcontroller, also described as a 16-bit MCU. Its MSP430 architecture supports interrupt-driven control, while the integrated analog and communication peripherals reduce the need for external components in cost-sensitive embedded systems. The principal device characteristics include a maximum clock frequency of 16 MHz, 2 KB of Flash program memory, 128 B of SRAM, 10-bit ADC capability, and integrated I2C and SPI interfaces. The device also includes a built-in 16-bit timer and ten I/O pins. Its digitally controlled oscillator allows the MSP430F20xx family to wake from low-power modes to active mode in less than 1 microsecond, which is valuable for intermittent measurement and control systems. The mixed-signal feature set allows the MCU to manage both digital control functions and analog inputs. The 10-bit ADC can serve temperature, potentiometer, light, and other sensor-conditioning systems, while the timer supports periodic sampling, timing, and control functions. I2C and SPI provide paths to external sensors, displays, memories, transceivers, and other digital peripherals without requiring parallel data buses. Typical uses include battery-operated instruments, environmental monitoring, industrial sensing nodes, compact control panels, appliance interfaces, and portable measurement equipment. In these systems, the MSP430F2012TN can sample an analog input, apply decision logic, update an actuator, and communicate results over I2C or SPI. The 14-pin PDIP format is particularly useful for prototypes, educational platforms, and through-hole industrial assemblies where a surface-mount package would be inconvenient. Designers should account for the limited 2 KB Flash and 128 B SRAM when sizing firmware, buffering data, and selecting a development toolchain. External sensing circuitry, decoupling, clock considerations, and serial-interface pull-ups should be evaluated against the system requirements. The exact pin assignments, electrical limits, and peripheral behavior must be confirmed in the Texas Instruments MSP430F20x1, MSP430F20x2, and MSP430F20x3 mixed-signal microcontroller documentation. This page combines the verified manufacturer and distributor specifications with purchasing guidance, application context, same-family drop-in candidates, and practical selection considerations. It also identifies unavailable commercial and pin-level data explicitly so engineers can distinguish confirmed facts from items that require confirmation from the manufacturer documentation.

RFQ संपर्क
MSP430F2013IN - 16MHz Ultra-Low-Power 16-Bit MCU | Texas Instruments
MSP430F2013IN

MSP430F2013IN - 16MHz Ultra-Low-Power 16-Bit MCU | Texas Instruments

Texas Instruments MSP430F2013IN is a 16 MHz ultra-low-power mixed-signal microcontroller with a 16-bit RISC CPU, 2KB of Flash memory, 128B of RAM, one 16-bit sigma-delta ADC, and a USI supporting SPI and I2C in a 14-pin PDIP package. It operates from 1.8 V to 3.6 V and is specified for an industrial temperature range of -40°C to 85°C. The 16 MHz clock, 125 ns instruction cycle, and 10 I/O pins make the device suitable for compact embedded measurement and control systems. A mixed-signal microcontroller combines a digital microcontroller core with analog measurement or communication resources. In the product hierarchy, MSP430F2013IN is a 16-bit RISC microcontroller within the MSP430 family and MSP430F2x series. It is designed for portable measurement applications that need low-power operation, flexible serial communication, and direct sensor interfacing without requiring a larger mixed-signal processor. Key device features include 2KB of Flash program memory, 128B of RAM, 10 I/O ports, one 16-bit sigma-delta ADC, and one Universal Serial Interface for SPI or I2C. The MSP430 architecture provides five low-power modes to support battery-powered operation. The FLL+ frequency-locked loop supports controlled clocking, while the USI reduces the number of external communication components required in compact sensor nodes. The device's 16-bit RISC architecture uses 16-bit registers and a 125 ns instruction cycle. At a 16 MHz operating frequency, it provides substantially more processing throughput than lower-rate MSP430 devices while retaining the family's compact and energy-conscious architecture. The sigma-delta ADC supports applications that measure slow-changing analog quantities such as temperature, pressure, light, or resistive sensor outputs. Typical uses include portable environmental monitors, industrial sensor interfaces, low-power data loggers, battery-powered instruments, connected measurement nodes, and embedded control products. The USI can connect to SPI or I2C peripherals, while the ADC can acquire analog sensor signals. Developers can also use timer and general-purpose I/O resources for control signals, status indication, and system coordination. When designing around MSP430F2013IN, prioritize the 1.8 V to 3.6 V supply range and maintain decoupling close to the device. Account for the limited 2KB Flash and 128B RAM budgets during firmware planning. Because the 14-pin PDIP is intended for through-hole assembly rather than high-density automated PCB production, verify connector spacing, mechanical clearances, and rework requirements before committing it to a compact production design. This page consolidates verified manufacturer and distributor information, practical low-power design considerations, application guidance, and drop-in replacement analysis. It distinguishes confirmed specifications from unavailable details, making the MSP430F2013IN easier to evaluate for embedded sensing, serial-interface, and portable industrial-control designs.

RFQ संपर्क
MSP430F2013TN - 16MHz Sensing MCU with 16-Bit ADC | TI
MSP430F2013TN

MSP430F2013TN - 16MHz Sensing MCU with 16-Bit ADC | TI

Texas Instruments MSP430F2013TN is a 16 MHz mixed-signal sensing microcontroller with one 16-bit sigma-delta ADC, USI support for SPI and I2C, 2 KB Flash, 128 B RAM, and a 14-pin DIP package. Its 16-bit RISC architecture and 125 ns instruction cycle support efficient embedded measurement and control, while the frequency-locked-loop clock provides a stable operating foundation for precision sensing systems. A mixed-signal microcontroller, or sensing MCU, integrates digital processing with analog measurement resources on one device. The MSP430F2013 belongs to the MSP430 family of ultra-low-power embedded controllers, combining a 16-bit RISC CPU, mixed-signal peripherals, and low-power operating modes. This hierarchy places it below general-purpose processing and above compact embedded sensing platforms used for instrumentation, metering, control, and communication-assisted measurement. The primary mixed-signal feature is one 16-bit sigma-delta ADC, which is appropriate for slowly varying or heavily filtered sensor signals where fine resolution is more important than very high conversion speed. The universal serial interface provides SPI and I2C connectivity for external sensors, memories, and peripheral devices. Two kilobytes of Flash preserve firmware and configuration data, while 128 bytes of RAM support working state in space-constrained designs. The MSP430 CPU16 provides 16-bit processing, and the 125 ns instruction cycle corresponds to a 16 MHz operating frequency. A frequency-locked loop, or FLL+, supports clocking in low-power embedded designs, while the device can wake from standby in less than 6 microseconds. Multiple power-saving modes, including a 0.1 microamp off mode with RAM retention, help reduce energy consumption between measurement and communication activities. Typical uses include low-cost sensor nodes, industrial measurement modules, portable instrumentation, and connected sensing products. The sigma-delta ADC suits resistive, temperature, and slow analog-front-end signals, while the USI allows compact designs using either serial protocol. Designers can pair the MCU with external signal conditioning when the source requires filtering, excitation, or a differential input arrangement. The primary design consideration is power-rail and clock configuration. The available verified data does not state the recommended operating voltage range, so supply selection must be completed from the manufacturer datasheet rather than inferred. Decoupling, ADC input conditioning, and USI bus implementation also require care to prevent measurement noise or communication timing problems. This product record combines verified manufacturer and distributor information, price and availability context, strict drop-in replacement analysis, and practical application guidance. It clearly separates confirmed specifications from parameters that still require datasheet verification, helping engineers make a faster and more reliable design decision.

RFQ संपर्क
MSP430F2013TPW - 16MHz Low-Power MCU | Texas Instruments
MSP430F2013TPW

MSP430F2013TPW - 16MHz Low-Power MCU | Texas Instruments

The Texas Instruments MSP430F2013TPW is a 16-bit mixed-signal microcontroller operating at up to 16 MHz, with 2 KB of Flash memory and 128 bytes of RAM. It includes one 16-bit sigma-delta ADC and a Universal Serial Interface supporting SPI and I2C, and is packaged in a 14-pin TSSOP (PW). The device is designed for low-power sensing and embedded measurement systems operating from a 2.5 V or 3.3 V supply. A mixed-signal microcontroller combines a digital microcontroller core with analog measurement or communication peripherals on one device. The MSP430 is an ultra-low-power MCU family based on a 16-bit RISC architecture. Within the semiconductor hierarchy, MSP430F2013 belongs to the MSP430 mixed-signal microcontroller family and provides a compact platform for sensor acquisition, low-power instrumentation, and small control systems. The MSP430F2013TPW combines a 16 MHz CPU16 core with 2 KB of Flash and 128 bytes of RAM. Its 16-bit sigma-delta ADC supports analog sensing, while the USI provides flexible serial communication for SPI or I2C peripherals. The -40°C to 105°C temperature range suits industrial equipment, and the 14-pin TSSOP package supports compact surface-mount PCB layouts. Its mixed-signal architecture reduces the number of separate components required in a measurement system. The ADC can acquire sensor signals, while firmware can process the results and communicate through the USI. Five low-power operating modes help the MCU control energy use during idle and standby intervals, making the device appropriate for battery-powered and duty-cycled sensing products. Typical uses include portable environmental monitors, industrial process sensors, low-cost instrumentation, smart sensor nodes, and compact control modules. The combination of a 16-bit ADC, serial interface, low-power architecture, and 3.3 V operation is especially useful when a design needs local measurement and short-range serial connectivity without a larger mixed-signal MCU package. When laying out the circuit, follow the pin-description and recommended application circuits in the Texas Instruments MSP430F20x1, MSP430F20x2 and MSP430F20x3 datasheet. Keep analog and digital return paths separated, provide the required bypass capacitance close to the supply pins, and validate ADC accuracy with the intended sensor and signal-conditioning network. This product page combines the exact ordering information, interface capabilities, package details, selection guidance, practical design notes, and technically constrained drop-in alternatives for engineers evaluating the MSP430F2013TPW for compact, low-power sensing designs.

RFQ संपर्क
MSP430F2122IPW - 16MHz, 4KB Flash Mixed-Signal MCU | Texas Instruments
MSP430F2122IPW

MSP430F2122IPW - 16MHz, 4KB Flash Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430F2122IPW is a 16 MHz mixed-signal microcontroller with a 16-bit RISC CPU, 4KB Flash memory, 512B SRAM, a 10-bit ADC, comparator, and I2C, SPI, and UART interfaces, housed in a 28-pin TSSOP package. It is designed for compact embedded systems that need low power consumption, mixed-signal measurement, and serial connectivity in a single device. A microcontroller is the central programmable component in an embedded control system, combining a processor core, memory, analog peripherals, digital interfaces, and power-management functions. The MSP430 family is positioned within the hierarchy of microcontrollers, embedded processors, and semiconductors. Its mixed-signal architecture allows an application to acquire analog measurements, compare sensor signals, and communicate with external equipment without requiring several separate devices. The MSP430F2122IPW provides 16 MHz processing performance and a 16-bit RISC architecture with 16-bit registers and constant generators. Its 4KB Flash memory provides program storage, while 512B of SRAM supports working data, stack operations, and buffer management. Integrated peripherals include a 10-bit ADC, comparator, I2C, SPI, and UART, giving the device a practical mix of measurement, control, and communications functions for embedded designs. The MSP430 platform is optimized for low-power operation and includes multiple low-power modes according to the manufacturer product information. The device can therefore remain responsive while reducing unnecessary activity in battery-powered instrumentation, portable measurement systems, and low-duty-cycle sensor products. The 28-pin TSSOP package is also suitable for compact through-hole PCB assembly and hand-soldered prototypes. Typical uses include portable environmental monitoring, industrial sensor interfaces, low-power data loggers, battery-powered measurement instruments, and compact control systems requiring more than one serial interface. In these applications, the ADC and comparator support analog front-end processing while I2C, SPI, and UART provide connections to sensors, memory, host computers, or wireless modules. When laying out the PCB, follow the manufacturer pin and package guidance, provide clean supply decoupling, and route analog inputs away from noisy switching nodes. Firmware should use the low-power modes and peripheral interrupt mechanisms to control energy use. When upgrading an existing design, verify the exact device suffix, package, memory size, and peripheral requirements before treating another MSP430 device as a replacement. This product page combines the MSP430F2122 architecture, memory and interface specifications, application guidance, practical design notes, and qualified drop-in alternatives to support component selection and board-level implementation.

RFQ संपर्क
MSP430F2131IDW - 16MHz 8KB Ultra-Low-Power MCU | TI
MSP430F2131IDW

MSP430F2131IDW - 16MHz 8KB Ultra-Low-Power MCU | TI

The Texas Instruments MSP430F2131IDW is an ultra-low-power 16-bit mixed-signal microcontroller operating at 16 MHz, with 8 KB of flash memory, 256 bytes of SRAM, and 16 general-purpose I/O pins in a 20-pin SOIC package. Its integrated 16-bit timer and analog comparator support compact sensing, timing, control, and signal-processing systems. A mixed-signal microcontroller combines a digital processing core with analog or timing peripherals on one integrated circuit. The MSP430 architecture belongs to the microcontroller, embedded-processing, semiconductor, and power-management IC hierarchies. It is designed for compact systems that must acquire analog information, process it digitally, and then communicate results to a display, sensor network, or host controller. The MSP430F2131 is positioned for low-power, mixed-signal embedded designs rather than high-pin-count connectivity or high-memory applications. The principal features are a 16 MHz clock, 8 KB of flash memory, and 256 bytes of SRAM. Sixteen I/O pins provide interfaces for sensors, actuators, indicators, and external control logic. A built-in 16-bit timer supports event counting, periodic timing, and timing-sensitive control functions, while the analog comparator enables threshold-based signal decisions. These resources allow a compact design to perform measurement and control without relying on a separate timer IC. The MSP430F2131 uses a 16-bit CPU and an integrated mixed-signal peripheral set optimized for low-power embedded processing. Its 8 KB flash provides program storage, while the 256-byte SRAM accommodates working variables, stack operations, and short-lived data buffers. Designers should size firmware and RAM carefully because the memory budget is modest compared with contemporary 32-bit microcontrollers. The 20-pin SOIC footprint supports conventional surface-mount assembly while keeping the device compact. Typical uses include battery-powered sensor nodes, industrial condition-monitoring modules, simple measurement instruments, timers, and low-power control boards. The timer and comparator can work together in applications such as threshold detection, pulse counting, event duration measurement, and basic closed-loop control. The 16 I/O pins allow the MCU to supervise simple human-interface elements while retaining communication pins for a host or peripheral. For PCB implementation, use the manufacturer pin-description table and recommended application circuit when assigning tracks. Pay particular attention to decoupling, exposed programming and reset behavior, unused-pin treatment, and the clock implementation. Confirm the required supply range, analog-reference arrangement, and peripheral limits against the manufacturer datasheet before release. This page combines the MSP430F2131IDW's core specifications with package guidance, sourcing workflows, drop-in replacement analysis, and practical mixed-signal design considerations. It is intended to accelerate component selection, firmware planning, PCB review, and prototype bring-up for engineers working with the MSP430x21x1 family.

RFQ संपर्क
MSP430F2132CY - 16MHz 16-Bit MCU with 8KB Flash | Texas Instruments
MSP430F2132CY

MSP430F2132CY - 16MHz 16-Bit MCU with 8KB Flash | Texas Instruments

Texas Instruments MSP430F2132CY is a 16-bit ultra-low-power mixed-signal microcontroller built around a 16 MHz MSP430 RISC core, with 8KB of Flash memory and 512 bytes of SRAM. The device also provides a 10-bit ADC, analog comparator, and communication peripherals including I2C, SPI, and UART. The MSP430F2132CY ordering code is offered as a die-sale product, so the verified ordering information does not identify a conventional leaded or surface-mount package for this specific suffix. An ultra-low-power microcontroller is an embedded processing IC designed to balance compute capability, analog measurement, serial communications, and energy efficiency. The MSP430F2132 belongs to the MSP430 family, whose hierarchy is MSP430 mixed-signal microcontroller, RISC microcontroller, embedded microcontroller, and semiconductor. Its architecture is intended for portable measurement and control products that require more than simple digital I/O but benefit from compact code, built-in analog conversion, and multiple low-power operating modes. The principal device parameters include a 16-bit CPU operating at up to 16 MHz, 8KB of Flash memory, 512B of SRAM, a 10-bit ADC, and an analog comparator. The integrated communication capability covers I2C, SPI, and UART, allowing the MCU to connect sensors, displays, transceivers, and external data-acquisition hardware without requiring separate interface controllers. The MSP430 architecture also provides dedicated handling for timed capture, timing, and mixed-signal measurement tasks common in portable instruments. The MSP430F2132 family is suitable for battery-powered measurement, industrial sensing, building-control equipment, compact instrumentation, and connected low-power nodes. An ADC and comparator can share the same silicon with the digital core, reducing board area in designs that measure an analog quantity and then communicate the result. The 8KB Flash capacity provides a defined code-storage budget, while 512B of SRAM supports working state, stack, buffers, and peripheral data handling. Because MSP430F2132CY is supplied as a die-sale product, engineers should confirm die orientation, bonding requirements, assembly process, exposed features, quality requirements, and production handling directly with Texas Instruments before committing the device to a PCB or automated assembly flow. The CY ordering suffix should not be interpreted as a finished package designation. This page consolidates verified manufacturer and distributor information, current price breaks, technical specifications, and purchasing guidance for MSP430F2132CY. It also identifies where package, pinout, compliance, and exact substitute data remain unavailable so engineers can avoid treating unverified package or cross-reference assumptions as production facts.

RFQ संपर्क
MSP430F2132IPW - 16MHz Low-Power MCU | Texas Instruments
MSP430F2132IPW

MSP430F2132IPW - 16MHz Low-Power MCU | Texas Instruments

The Texas Instruments MSP430F2132IPW is a 16 MHz ultra-low-power mixed-signal microcontroller with 8 KB of Flash memory, 512 B of SRAM, a 10-bit ADC, a comparator, and one USCI supporting I2C, SPI, or UART communication in a 28-pin TSSOP package. The MSP430F2xx device combines a 16-bit RISC CPU, 16-bit registers, and constant generators for efficient code execution. A mixed-signal microcontroller integrates computational control with analog measurement functions on a single device. In the product hierarchy, the MSP430F2132IPW is a 16-bit RISC microcontroller, part of the MSP430 mixed-signal family, and intended for embedded control, sensor acquisition, and low-power portable systems. Its analog peripherals reduce the need for separate converters in many instrument designs, while its serial interface supports connection to external sensors, transceivers, and display controllers. Key device attributes include a maximum CPU clock of 16 MHz, 8 KB of Flash for program storage, and 512 B of SRAM for working memory. A 10-bit ADC supports analog measurements, and an integrated comparator can perform threshold or low-power state-detection functions. One USCI provides I2C, SPI, or UART operation, while five low-power modes help optimize energy consumption in battery-powered equipment. The MSP430 architecture emphasizes energy efficiency through a 16-bit RISC core, 16-bit registers, and constant generators that reduce instruction overhead. Five low-power operating modes allow firmware to disable unused peripherals and suspend the CPU during idle intervals. This makes the device suitable for portable measurement systems that spend substantial time waiting for a sensor, user input, or scheduled conversion rather than performing continuous computation. Typical applications include battery-powered environmental sensors, compact industrial data loggers, portable instrumentation, smart sensor nodes, and low-power monitoring systems. The 10-bit ADC supports analog sensor conditioning, the comparator supports threshold detection, and the configurable USCI can connect with serial sensors or digital transceivers. The 28-pin TSSOP package also supports compact, board-space-conscious designs. Designers should preserve the power-rail and decoupling requirements in the manufacturer datasheet, especially when the ADC is used. ADC accuracy depends on clean supply voltage, appropriate analog grounding, and careful routing of analog inputs away from digital switching nodes. Firmware should also use the documented low-power modes and peripheral clock controls rather than relying only on the CPU idle instruction. This product page combines the exact MSP430F2132IPW ordering information with memory and peripheral characteristics, practical application guidance, package information, and a conservative drop-in alternative analysis. The alternatives preserve the 28-pin TSSOP footprint where technically supportable, while the comparison notes identify memory and peripheral differences that must be checked before redesigning an existing board.

RFQ संपर्क
MSP430F2232IDA - 16-Bit 16MHz Ultra-Low-Power MCU | Texas Instruments
MSP430F2232IDA

MSP430F2232IDA - 16-Bit 16MHz Ultra-Low-Power MCU | Texas Instruments

Texas Instruments MSP430F2232IDA is a 16-bit mixed-signal microcontroller built around the MSP430 CPU16 architecture, operating at up to 16 MHz with 8 KB of flash memory and 512 B of SRAM in a 38-pin TSSOP package. It operates from 1.8 V to 3.6 V and integrates UART, SPI, I2C, timers, and mixed-signal peripherals for low-power embedded measurement and control designs. A microcontroller is a programmable semiconductor that combines a processor core, memory, and peripherals on one integrated circuit. The MSP430 belongs to the embedded microcontroller hierarchy and is optimized for portable measurement systems where energy efficiency and fast wake-up are more important than maximum processor throughput. Its 16-bit RISC CPU, 16-bit registers, constant generators, and 125 ns instruction-cycle capability support compact control code across sensor, communications, and industrial applications. The MSP430F2232IDA provides ultra-low-power operation through active, standby, and off modes. At 1 MHz and 2.2 V, active-mode current is 270 µA, standby current is 0.7 µA, and off-mode current with RAM retention is 0.1 µA. The device can wake from standby in less than 1 µs, making it suitable for duty-cycled instruments that must respond quickly while conserving battery energy. Its integrated communication resources include UART, SPI, and I2C interfaces. These allow the MCU to connect local sensors, transceivers, displays, and data-acquisition hardware without requiring separate serial-interface controllers. A timer subsystem supports periodic timing and event handling, while the mixed-signal feature set enables compact instrumentation designs in which analog measurements and digital control share the same device. Typical applications include portable environmental monitors, industrial sensor nodes, low-power data loggers, building-automation endpoints, and compact measurement instruments. The 1.8 V minimum supply voltage also makes it relevant to energy-harvesting and coin-cell powered systems when the external load and sensor circuitry are designed for the same voltage range. The principal design consideration is maintaining a complete low-power design rather than treating the MCU alone as an energy-saving component. Select peripheral clocks, sleep durations, pull-up values, and analog front-end biasing to match the measurement workload. Use the manufacturer pin-description table and mixed-signal peripheral guidance when assigning the 38 TSSOP pins and planning decoupling. This product overview combines the exact orderable MPN, manufacturer feature data, package information, interface capabilities, and practical selection guidance. It also identifies the limits of drop-in sourcing by distinguishing electrically close family options from a verified cross-manufacturer replacement, helping engineers make PCB-level decisions with greater confidence.

RFQ संपर्क
MSP430F2272IDA - 16MHz 32KB Flash Mixed-Signal MCU | TI
MSP430F2272IDA

MSP430F2272IDA - 16MHz 32KB Flash Mixed-Signal MCU | TI

Texas Instruments MSP430F2272IDA is a 16-bit ultra-low-power mixed-signal microcontroller with a 16 MHz MSP430 RISC CPU, 32KB Flash memory, 512B SRAM, a 10-bit ADC, and I2C, SPI, and UART interfaces in a 38-pin TSSOP package. A microcontroller is a programmable semiconductor system that combines a CPU, memory, and peripherals on one integrated circuit. The MSP430F2272 belongs to the MSP430 mixed-signal microcontroller family and uses a 16-bit RISC architecture with 16-bit registers and constant generators. Its integrated analog and communications peripherals allow compact designs to measure signals, control actuators, and communicate with external sensors without requiring several separate devices. The device operates at up to 16 MHz with a 125 ns instruction cycle time. Its 32KB Flash provides program storage, while 512B SRAM supports working memory for embedded control routines. The 10-bit ADC supports analog measurement tasks, and the I2C, SPI, and UART interfaces provide options for connecting sensors, displays, transceivers, and other digital peripherals. The five power-saving modes support duty-cycled designs where standby or off-state consumption matters. The mixed-signal feature set makes the MSP430F2272 suitable for industrial instrumentation, sensor conditioning, portable measurement equipment, small control systems, and embedded communication nodes. The FLL+ frequency-locked loop supports controlled clock operation, while scan capability enables background instruction execution and can improve responsiveness in interrupt-driven designs. Designers should pay close attention to the 38-pin TSSOP footprint, pin multiplexing, and the power budget of the selected operating mode. The ADC reference, communication baud rates, and firmware timing should be checked against the system clock and noise requirements. The low-power architecture is most valuable when firmware can place the MCU into a suitable standby mode during idle periods. This product page combines manufacturer specifications, application guidance, drop-in replacement information, comparison parameters, and practical layout notes to help engineers move from component selection to a complete embedded design.

RFQ संपर्क
MSP430F233TPM - 16MHz 16-Bit Ultra-Low-Power MCU | Texas Instruments
MSP430F233TPM

MSP430F233TPM - 16MHz 16-Bit Ultra-Low-Power MCU | Texas Instruments

Texas Instruments MSP430F233TPM is a 16-bit ultra-low-power mixed-signal microcontroller with a 16 MHz MSP430 RISC CPU, 8 KB Flash memory, 1 KB SRAM, a 12-bit ADC, comparator, hardware multiplier, and I2C, SPI, and UART connectivity. The device operates from a 1.8 V to 3.6 V supply and is housed in a 64-pin LQFP (PM) package for industrial, embedded, IoT, metering, motor-control, and portable measurement applications. A microcontroller is a compact embedded-computer system that combines a CPU, memory, peripheral interfaces, and power-management functions on one integrated circuit. The MSP430 belongs to the mixed-signal microcontroller category, which extends the general embedded MCU hierarchy with analog conversion and comparison functions. Its 16-bit RISC architecture uses 16-bit registers and constant generators, while five low-power modes and fast standby wake-up support battery-powered and energy-conscious designs. The MSP430F233 combines 8 KB Flash with 1 KB SRAM and a maximum clock frequency of 16 MHz. Its 12-bit ADC enables analog measurement, and the integrated comparator supports thresholding and basic signal conditioning. Four USCI modules provide serial connectivity for I2C, SPI, and UART configurations. Two 16-bit timers support timing, capture, compare, and periodic event generation, making the device useful for sensor acquisition, industrial control, and compact embedded measurement systems. The MSP430F23x family is designed around a mixed-signal architecture and low-power operation. The FLL+ frequency-locked-loop system supports clock control, while the CPU provides a 125 ns instruction cycle at 16 MHz according to the family technical description. The device can operate across multiple low-power states, including standby and RAM-retention off modes, allowing firmware to reduce activity when the application does not require continuous processing. Typical uses include low-power sensor nodes, battery-operated instrumentation, industrial meters, building-control endpoints, compact motor-control interfaces, and connected IoT devices. The 12-bit ADC is useful for battery, temperature, potentiometer, and analog sensor interfaces, while USCI peripherals simplify communication with external sensors, displays, transceivers, and data loggers. The LQFP package provides accessible leads and is suitable for through-hole assembly or conventional board-level manufacturing processes. Designers should pay attention to the 1.8 V to 3.6 V supply range, peripheral pin multiplexing, clock configuration, and low-power state transitions. Place decoupling capacitors close to the supply pins, follow the pin-description table in the manufacturer datasheet when allocating I/O, and confirm the ADC input range and accuracy requirements for the selected operating conditions. For battery systems, account for standby and wake-up current alongside active-mode consumption. This product page combines manufacturer device information, verified distributor listings, package and ordering details, application guidance, comparison parameters, and practical design notes. It is intended to help engineers identify the correct MSP430F233TPM configuration, plan PCB and firmware changes, and assess replacement options without overlooking the distinction between electrical equivalence and true pin-to-pin drop-in compatibility.

RFQ संपर्क