उत्पाद (44,000+)

MSP430FR2433IRGER - 16MHz FRAM MCU | TI
MSP430FR2433IRGER

MSP430FR2433IRGER - 16MHz FRAM MCU | TI

The Texas Instruments MSP430FR2433IRGER is a 16 MHz ultra-low-power 16-bit microcontroller based on the MSP430 CPU16 core, featuring 15.5KB FRAM, 4KB SRAM, a 10-bit ADC, UART/SPI/I2C, and timers, housed in a 24-pin VQFN (RGE) 4x4 mm package. A microcontroller (MCU) is a compact integrated circuit designed to govern a specific operation in an embedded system, containing a processor core, memory, and programmable input/output peripherals. Within the taxonomy, an MCU is an embedded processor and a type of integrated circuit. The MSP430 family is a 16-bit ultra-low-power microcontroller line known for extended battery life and is part of Texas Instruments' Value Line sensing portfolio. Key features of the MSP430FR2433IRGER include a 16 MHz CPU frequency, 15.5KB of ferroelectric RAM (FRAM), 4KB of SRAM, a 10-bit analog-to-digital converter (ADC), and serial interfaces including UART, SPI, and I2C. It operates from 1.8V to 3.6V and is specified for -40°C to +85°C. FRAM provides non-volatile storage with high write endurance and fast write speeds, making it suitable for data logging and battery-powered sensing. The CPU16 core uses a von-Neumann architecture with a unified memory space, a hardware multiplier, and low-power modes LPM0-LPM4. These modes allow the device to wake quickly from deep sleep while consuming minimal current, which is critical for portable and energy-harvesting designs. The integrated 10-bit ADC with internal reference simplifies direct connection of analog sensors without external converter ICs. Typical applications include industrial sensors, medical and health monitoring devices, smart meters, portable instrumentation, and IoT sensor nodes. The combination of low power, non-volatile FRAM, and the compact VQFN-24 package makes the MSP430FR2433IRGER especially suited for space-constrained designs that must retain data during power loss. When designing with this MCU, tie the exposed thermal pad on the bottom of the VQFN package to the PCB ground plane for optimal thermal and electrical performance. Place 100 nF and 10 µF decoupling capacitors close to the supply pins. For lowest power consumption, use the low-power modes and disable unused peripherals in firmware. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, providing a convenient engineering reference for the MSP430FR2433IRGER.

RFQ संपर्क
MSP430FR2476TPT - 16MHz MCU 64KB FRAM 48-LQFP | Texas Instruments
MSP430FR2476TPT

MSP430FR2476TPT - 16MHz MCU 64KB FRAM 48-LQFP | Texas Instruments

The Texas Instruments MSP430FR2476TPT is a 16-bit RISC mixed-signal microcontroller in the MSP430FRxx value-line portfolio, integrating 64KB of FRAM, 8KB of SRAM, and a 12-bit ADC in a 48-pin LQFP (TPT) package. The CPU16 core runs up to 16 MHz and is paired with ultra-low-power peripherals for sensing and measurement applications. Wide supply voltage range from 3.6V down to 1.8V (minimum supply voltage is restricted by SVS levels) supports battery and energy-harvesting designs. What is an MSP430 FRAM MCU? An MSP430 FRAM microcontroller is a 16-bit ultra-low-power MCU that uses Ferroelectric Random Access Memory (FRAM) instead of flash for non-volatile code and data storage. FRAM combines the speed of SRAM with the non-volatility of flash, enabling faster writes (100x faster than flash), higher endurance (10^15 write cycles vs 10^5 for flash), and unified memory for code/data, which simplifies firmware design and enables in-field data logging at high rates. FRAM MCUs sit in the broader taxonomy: microcontroller -> embedded MCU -> 16-bit MCU -> ultra-low-power MCU -> MSP430 family -> FRAM value line. Key features of the MSP430FR2476TPT include: 16 MHz CPU16 core, 64.5KB (64K x 8) FRAM program/data memory, 8KB SRAM, an integrated 12-bit SAR ADC with multiple channels, an analog comparator, hardware UART/SPI/I2C, multiple 16-bit timers, and an intelligent digital peripherals interface. The device ships in a 48-pin LQFP (7x7 mm) package suitable for low-cost PCB designs. The architecture centers on a 16-bit RISC core optimized for low active current and ultra-low standby current, enabling years of operation on a single coin cell. FRAM enables byte-addressable non-volatile storage with near-instant write times, allowing data logging and wireless firmware updates without the erase-then-write cycle penalty of flash. The 12-bit ADC supports internal voltage reference and temperature sensor channels for direct sensor interfacing. Typical applications for the MSP430FR2476TPT include battery-powered sensor nodes, IoT end nodes, low-cost data loggers, energy-harvesting devices, smoke/CO detectors, smart thermostats, fitness wearables, and home automation peripherals. The combination of low cost, ultra-low power, and integrated analog peripherals makes it well suited for always-on sensing applications where energy budget is measured in microwatts. When designing with the MSP430FR2476TPT, follow the MSP430 hardware user's guide for SVS threshold settings, decoupling capacitor placement, and JTAG/SBW programming connections. Use the MSP-TS430PZ48 target board for development and the free MSP430Ware/Code Composer Studio toolchain for code development. Pay attention to the SVS minimum supply voltage restriction to avoid brown-out at low VCC. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not consolidated in the manufacturer datasheet. The MSP430FR2476TPT is a member of the wider MSP430FR247x family and shares the same 48-LQFP (TPT) footprint across the TPT and TPTR tape-and-reel variants.

RFQ संपर्क
MSP430FR5989IPMR - 128KB FRAM 16MHz Rotary Sensing MCU | TI
MSP430FR5989IPMR

MSP430FR5989IPMR - 128KB FRAM 16MHz Rotary Sensing MCU | TI

The Texas Instruments MSP430FR5989IPMR is a 16-bit ultra-low-power microcontroller based on the MSP430 CPUXV2 RISC core running at up to 16MHz, with 128KB embedded FRAM, 2KB SRAM, and an extended Scan Interface 2 for rotary sensing, housed in a 64-pin LQFP (PM) 10x10mm package. A microcontroller (MCU) is a compact integrated circuit that combines a processor core, program memory, data memory, and programmable peripherals on a single die to govern a specific embedded function. Within the MCU hierarchy, this device belongs to the MSP430 FRAM family of ultra-low-power (ULP) microcontrollers under the broader MSP430 platform and power-management IC taxonomy. Its FRAM (ferroelectric RAM) memory unites SRAM-like speed, flexibility, and endurance with flash-like non-volatility at much lower write energy, eliminating the erase-before-write cycles of conventional flash. Key features include the extended Scan Interface 2 that offloads high-resolution rotary and linear position sensing from the CPU, a hardware AES accelerator for secure metering data, a real-time clock with calendar mode, a 12-bit ADC, comparator, DMA controller, a 32-bit hardware multiplier, and multiple 16-bit timers. Power performance is exceptional: active mode draws approximately 100 uA/MHz and standby (LPM3 with VLO) about 0.4 uA, enabling decade-class battery life in field instruments. Architecturally, the CPUXV2 core executes a 16-bit RISC instruction set over a von Neumann bus at 16MHz. FRAM is byte-writable in-system, allowing fast data logging without external EEPROM, while the AES accelerator encrypts measurements for smart-grid and flow-metering security. The operating supply range is 1.8V to 3.6V with -40C to +85C temperature tolerance for harsh deployments. Typical applications include gas, water, and heat flow meters, rotary and linear position sensing systems, smart-grid endpoints, industrial process control, and secure wireless sensor nodes. Scan Interface 2 directly supports rotary encoders while the CPU sleeps, minimizing average current. Design tip: decouple each VCC pin with 100nF close to the pin plus 10uF bulk capacitance, keep the supply above the SVS threshold for reliable FRAM writes, and use JTAG or two-wire Spy-Bi-Wire for debugging. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

USD $6.30 संपर्क
MSP430FR5994 - 16MHz 256KB FRAM MCU with LEA | TI
MSP430FR5994

MSP430FR5994 - 16MHz 256KB FRAM MCU with LEA | TI

The Texas Instruments MSP430FR5994 is a 16-bit ultra-low-power microcontroller operating at up to 16 MHz, with 256KB of non-volatile FRAM memory, 8KB of SRAM, a Low-Energy Accelerator (LEA) coprocessor for DSP-style math, and a 64-pin LQFP (10x10 mm) package option. A microcontroller (MCU) is a single-chip embedded computer combining a processor core, memory, and peripherals. The MSP430FR5994 belongs to the 16-bit MCU class, within the broader family of microcontrollers and embedded processors, and sits in TI's MSP430 FRAM platform - a product line that replaces flash memory with ferroelectric RAM for faster, lower-power, and far more durable writes in a unified non-volatile memory architecture. Key differentiating features include the LEA (Low-Energy Accelerator), which TI states delivers up to 40x the DSP performance of Arm Cortex-M0+ class cores for functions such as FFT, FIR filtering, and matrix multiplication, without requiring DSP expertise. The 256KB FRAM supports memory writes at very low energy compared to flash, and the device integrates a 12-bit ADC, comparator, DMA, AES accelerator, and UART/SPI/I2C serial interfaces, plus multiple 16-bit timers. Architecturally, the MSP430FR5994 uses the MSP430 CPUXV2 16-bit RISC core, a hallmark of the lowest-power MCU technology platform on the market. The unified FRAM memory allows code and data to coexist in non-volatile storage, enabling in-application software updates and rapid data logging. Typical applications include battery-powered metering, portable medical and sensor-monitoring equipment, industrial sensing nodes, and edge signal-processing tasks where LEA-accelerated FFT and FIR computation offloads the main CPU. A key design consideration: FRAM writes consume far less energy than flash programming, but designers should still manage the unified memory map carefully when partitioning persistent data segments. This page synthesizes distributor availability data, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MSP430FR59941IPM - 16MHz 256KB FRAM MCU | TI
MSP430FR59941IPM

MSP430FR59941IPM - 16MHz 256KB FRAM MCU | TI

The Texas Instruments MSP430FR59941IPM is a 16-bit MSP430FR FRAM microcontroller running at up to 16 MHz with 256KB non-volatile FRAM, 8KB SRAM, and a Low-Energy Accelerator (LEA) DSP coprocessor, housed in a 64-pin LQFP (PM) package measuring 10x10 mm and rated from -40C to +85C. A FRAM (Ferroelectric RAM) microcontroller is a class of mixed-signal MCU that replaces conventional flash program memory with ferroelectric memory, a technology that combines the non-volatility of flash with the write speed and endurance of SRAM. Within the power-management hierarchy of embedded systems, the MCU sits at the center of the signal chain, controlling sensors, interfaces, and power modes; FRAM MCUs occupy the low-power embedded processing tier, below application processors and above simple 8-bit controllers. Key differentiating features include 256KB of FRAM unified memory with unlimited write endurance in practice and uniform 128-byte write granularity, the LEA hardware accelerator that offloads vector math such as FFTs and FIR filters from the CPU at a fraction of the energy, a hardware AES256 cryptographic accelerator, and a 12-bit SAR ADC. The peripheral set also includes comparators, DMA, four eUSCI serial interfaces (UART/SPI/I2C), and 68 I/O lines made available through TI's port mapping architecture. Architecturally, the device uses the MSP430 CPUXV2 RISC core with 16-bit instructions, a flexible clock system (VLO, REFO, DCO, and external LFXT/HFXT sources), and multiple low-power modes (LPM0-LPM4.5) that let the MCU spend most of its life in sub-microamp sleep states. The FRAM write mechanism requires no erase cycle, so data logging writes are roughly 100x faster and far lower energy than flash-based writes. Typical applications include battery-powered metering and data logging, portable medical monitoring, sensor-fusion nodes performing DSP pre-processing via LEA, and secure connected endpoints using the AES256 engine. Designers should note that FRAM read timing is fast but the maximum system frequency of 16 MHz requires wait-state management for FRAM access above 8 MHz, and the LQFP-64 PM package needs a solid DVSS/DVCC decoupling network per TI's layout guidance. This page synthesizes distributor pricing, same-family drop-in alternatives, pinout guidance, and practical design notes not consolidated in the manufacturer datasheet.

RFQ संपर्क
MSP430FR59941IZVWR - 16MHz 256KB FRAM MCU 87-NFBGA | Texas Instruments
MSP430FR59941IZVWR

MSP430FR59941IZVWR - 16MHz 256KB FRAM MCU 87-NFBGA | Texas Instruments

The Texas Instruments MSP430FR59941IZVWR is a 16-bit MSP430FR59xx FRAM microcontroller running at 16 MHz with 256KB of FRAM nonvolatile memory, 8KB of SRAM, and a hardware Low-Energy Accelerator (LEA) for digital signal processing, housed in an 87-pin NFBGA (ZVW) 6x6 mm ball grid array package. It integrates a 12-bit ADC, comparator, DMA controller, AES cryptographic accelerator, and up to 68 general-purpose I/O lines with eUSCI serial communication modules. A FRAM (ferroelectric random access memory) microcontroller is a class of MCU in which program flash is replaced by ferroelectric memory, a technology that combines the nonvolatility of flash with the write speed, endurance, and ultra-low write energy of RAM. Within the power management hierarchy of embedded systems, FRAM MCUs occupy the extreme low-power end, enabling energy harvesting and battery designs that conventional flash MCUs cannot match. Key features include the LEA vector math accelerator, which offloads FFT, FIR, and matrix operations from the CPU at a fraction of the energy, and the AES256 accelerator for secure IoT deployments. FRAM writes at full 16 MHz speed with 10^15 cycle endurance, eliminating flash erase-before-write delays and enabling in-system data logging. Operating voltage spans 1.8V to 3.6V with active-mode currents in the microampere-per-MHz class and multiple low-power modes (LPM3.5/4.5) for battery designs. The CPUXV2 16-bit RISC core executes MSP430 instructions with a modernized pipeline. Peripherals include four eUSCI modules supporting UART, SPI, and I2C, a 12-channel DMA, a real-time clock, and a flexible clock system with DCO, LFXT, and HFXT sources. Typical applications include battery-powered metering, portable medical monitoring, energy harvesting sensor nodes, and secure IoT edge devices requiring cryptographic key storage and long battery life. Design consideration: the 87-NFBGA (0.8 mm ball pitch, 6x6 mm) demands careful PCB stack-up; escape routing typically requires a dedicated inner signal layer, and X-ray inspection is recommended for assembly. This page adds distributor pricing, drop-in alternative analysis, and layout guidance not found in the TI datasheet.

RFQ संपर्क
MSP430FR59941REV - 16MHz 256KB FRAM MCU with LEA | TI
MSP430FR59941REV

MSP430FR59941REV - 16MHz 256KB FRAM MCU with LEA | TI

The Texas Instruments MSP430FR59941REV is a 16-bit MSP430FR microcontroller (MCU) built on the MSP430 CPUXV2 core, running at up to 16 MHz with 256KB of non-volatile FRAM, 8KB of SRAM, and an integrated Low-Energy Accelerator (LEA) for digital signal processing. The device integrates AES hardware acceleration, a 12-bit ADC, comparators, DMA, 68 general-purpose I/O pins, and multiple eUSCI serial interfaces. FRAM (ferroelectric random access memory) is a non-volatile memory technology that combines the speed and low power of SRAM with the endurance and retention of Flash. In the power-management hierarchy, the MSP430FR59941 sits within the MSP430FR599x mixed-signal MCU family, part of TI's ultra-low-power MSP430 portfolio for embedded control and sensing applications. Key differentiating features include the LEA coprocessor, which TI states delivers 40x the signal-processing performance of Arm Cortex-M0+ MCUs for FFT, FIR, and matrix multiplication, without requiring DSP expertise. The 256KB FRAM enables large data logging with unlimited write endurance in practice, while the 12-bit ADC and AES accelerator support secure, precision sensing. Architecturally, the CPUXV2 16-bit RISC core pairs with the LEA vector engine, and FRAM is accessed at full speed, removing the erase-before-write penalties of Flash MCUs. Multiple low-power modes allow active currents in the microamp-per-MHz class, a hallmark of the MSP430 line. Typical applications include smart metering and energy monitoring, industrial sensor front ends with FFT-based analytics, secure IoT sensor nodes using the AES engine, and portable medical devices. Design consideration: FRAM requires no external programming voltage and survives power loss mid-write, but designers should verify the package and pinout details of the REV suffix ordering code directly against the MSP430FR599x datasheet before layout. This page synthesizes verified distributor listings, same-family drop-in alternatives, and practical design notes beyond what a single datasheet page provides.

RFQ संपर्क
MSP430FR5994IPMR - 16MHz 256KB FRAM MCU | Texas Instruments
MSP430FR5994IPMR

MSP430FR5994IPMR - 16MHz 256KB FRAM MCU | Texas Instruments

The Texas Instruments MSP430FR5994IPMR is a 16-bit ultra-low-power microcontroller based on the MSP430 CPUXV2 RISC core running at up to 16 MHz, integrating 256KB of FRAM non-volatile memory, 8KB of SRAM, a Low-Energy Accelerator (LEA) DSP engine, an AES256 accelerator, a 12-bit ADC, comparators, DMA, and UART/SPI/I2C serial interfaces in a 64-pin LQFP (10x10 mm, PM suffix) package. A microcontroller (MCU) is a single-chip embedded processor that combines a CPU core, memory, and peripherals on one die, sitting at the device level of the embedded-systems hierarchy (MCU -> embedded processor -> semiconductor). The MSP430FR599x family belongs to the MSP430 FRAM series, which replaces flash with ferroelectric RAM: FRAM offers fast, low-power writes, unified program and data memory, and very high write endurance, making it one of the lowest-power MCU memory technologies available. Key differentiators include the Low-Energy Accelerator (LEA), a hardware signal-processing engine that TI states delivers up to 40x the performance of Arm Cortex-M0+ MCUs on functions such as FFT, FIR filtering, and matrix multiplication, without requiring DSP expertise. The integrated AES256 accelerator secures IoT connectivity, and multiple low-power modes (LPM) extend battery life in always-on sensing applications. Architecturally, the 16-bit CPUXV2 core offloads vector math to LEA via the DMA controller, keeping the CPU in sleep while signal processing proceeds. FRAM is byte-writable with no sector-erase penalty, which simplifies data logging and over-the-air firmware updates. Typical applications include battery-powered sensor nodes, building automation and electronic metering, portable medical devices, and edge signal-conditioning nodes that need FFT/FIR processing at minimal energy cost. Design tip: partition FRAM deliberately - the unified memory allows constants in information segments, but code/data segmentation and write-endurance budgeting should follow TI's FRAM guidance in the MSP430FR599x, MSP430FR596x Mixed-Signal Microcontrollers datasheet (Rev. D). This page adds value beyond the datasheet by synthesizing drop-in alternatives (MSP430FR5989IPMR, MSP430FR59941IPM and related family parts), pricing context as of 2026-09-03, and practical design notes in one place.

RFQ संपर्क
MSP430FR5994IPNR - 16MHz 256KB FRAM MCU | Texas Instruments
MSP430FR5994IPNR

MSP430FR5994IPNR - 16MHz 256KB FRAM MCU | Texas Instruments

The Texas Instruments MSP430FR5994IPNR is a 16-bit ultra-low-power FRAM microcontroller running at 16 MHz with 256KB of FRAM nonvolatile memory, 8KB of SRAM, and an integrated Low-Energy Accelerator (LEA) for signal processing, housed in an 80-pin LQFP (12x12 mm) package. FRAM (ferroelectric random access memory) is a nonvolatile memory technology that combines the speed and low power of SRAM-like writes with the data retention of flash. In a microcontroller system hierarchy, the MSP430FR5994 sits within the broader family of mixed-signal MCUs, occupying the memory-and-signal-processing tier of the MSP430FR599x series, which targets battery-powered and energy-harvesting applications that require both large nonvolatile memory and mathematical computation. Key differentiating features include the LEA (Low-Energy Accelerator), a vector math coprocessor that offloads FFT, FIR, and matrix operations from the CPU while the core remains in a low-power state; hardware AES cryptography for secure data handling; a 12-bit ADC and analog comparator for sensing front ends; and direct memory access (DMA) for peripheral-to-memory transfers without CPU intervention. FRAM offers 100x faster writes than flash with inherently low write energy and virtually unlimited write endurance. Architecturally, the MSP430 CPUXV2 16-bit RISC core is paired with multiple low-power modes, enabling active currents in the microamp-per-MHz class while retaining RAM and peripheral state. The unified FRAM memory allows flexible partitioning between code and data, and the MPU (memory protection unit) can segment FRAM into protected regions for bootloader and data-logging designs. Typical applications include portable medical and health monitoring devices, building and factory sensor nodes, energy metering front ends, and battery-powered signal processing where the LEA accelerates FFT-based vibration or acoustic analysis. A key design consideration is the FRAM write protection scheme: configure the MPU segments early in development to prevent accidental data corruption, and respect the maximum operating frequency versus supply voltage relationship documented in the manufacturer datasheet. This page synthesizes distributor pricing, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MSP430FR5994IRGZR - 16MHz 256KB FRAM MCU | TI | Low Power
MSP430FR5994IRGZR

MSP430FR5994IRGZR - 16MHz 256KB FRAM MCU | TI | Low Power

The Texas Instruments MSP430FR5994IRGZR is a 16-bit RISC microcontroller based on the MSP430 CPUXV2 core running at 16 MHz, featuring 256KB of unified FRAM memory, 8KB of SRAM, and a Low-Energy Accelerator (LEA) for signal processing, housed in a 48-pin VQFN (7x7 mm) package. A microcontroller (MCU) is a single integrated circuit that combines a processor core, memory, and programmable peripherals into one chip, forming the lowest layer of the embedded-systems hierarchy: semiconductor -> microcontroller -> embedded system. The MSP430FR5994 belongs to the MSP430 FRAM family of ultra-low-power mixed-signal microcontrollers, where ferroelectric RAM replaces flash to combine non-volatility with fast, low-energy writes. Key differentiating features include FRAM unified memory with 256KB capacity that writes up to 100x faster than flash with far lower energy per byte, the LEA coprocessor delivering up to 40x the DSP performance of Arm Cortex-M0+ cores for FFT, FIR, and matrix operations without requiring DSP expertise, hardware AES encryption, a 12-bit ADC, analog comparators, DMA, and UART/SPI/I2C serial interfaces plus multiple timers. Technically, the FRAM architecture eliminates the erase-before-write penalty of flash, enabling true infinite-endurance data logging and instant software updates. The CPUXV2 16-bit RISC core emphasizes low active power, making the family suitable for battery-powered sensing where every microamp matters. The LEA offloads vector math from the CPU, cutting both execution time and energy per operation in edge signal-processing workloads. Typical applications include portable medical monitoring, industrial sensor nodes, battery-powered metering, and edge signal-conditioning systems that perform FFT or filtering on-chip. The combination of large non-volatile memory and a math accelerator fits data-logging and vibration-sensing designs particularly well. Design consideration: FRAM memory write operations are fast, but code must account for wait states at higher frequencies; use TI's driver library and the MSP430FR599x family datasheet for timing details. This page synthesizes distributor availability, family drop-in alternatives, and practical design guidance not found in a single manufacturer datasheet.

RFQ संपर्क
MSP430FR5994IZVW - 16MHz 256KB FRAM MCU, NFBGA-87 | TI
MSP430FR5994IZVW

MSP430FR5994IZVW - 16MHz 256KB FRAM MCU, NFBGA-87 | TI

The Texas Instruments MSP430FR5994IZVW is a 16-bit ultra-low-power MSP430 FRAM microcontroller featuring a 16 MHz CPUXV2 RISC core, 256KB of non-volatile FRAM memory, 8KB of SRAM, and an integrated Low-Energy Accelerator (LEA) for digital signal processing, housed in an 87-ball NFBGA (6x6 mm) package. An FRAM (ferroelectric random access memory) microcontroller is a class of mixed-signal MCU that replaces traditional flash program memory with ferroelectric RAM. FRAM offers byte-writable, non-volatile storage with dramatically faster write speeds, near-zero write energy, and essentially unlimited endurance compared to flash, making FRAM MCUs part of the broader power-management-focused, low-power semiconductor hierarchy. The MSP430 family pioneered this category and remains its most widely adopted representative. Key differentiating features of the MSP430FR5994 include the LEA vector coprocessor, which TI states delivers up to 40x the DSP performance of Arm Cortex-M0+ MCUs for functions such as FFT, FIR filtering, and matrix multiplication; hardware AES cryptographic acceleration; a 12-bit SAR ADC; an integrated comparator; a multi-channel DMA controller; and eUSCI serial peripherals supporting UART, SPI, and I2C. Multiple 16-bit timers enable motor control, capture/compare, and PWM applications with very low active and standby power consumption. Architecturally, the device is based on the MSP430 CPUXV2 core with unified FRAM program and data storage, allowing flexible memory partitioning under software control via the Memory Protection Unit (MPU). The LEA offloads block-based DSP math from the CPU, freeing cycles for application logic while operating in low-power modes. Typical applications include battery-powered metering and sensing nodes, industrial sensor front ends requiring FFT-based vibration or acoustic analysis, portable medical monitoring devices, and IoT edge endpoints where ultra-low standby power and long battery life are mandatory. A key design consideration is FRAM write protection: configure the MPU segment boundaries early in development to protect persistent data structures from firmware updates. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

RFQ संपर्क
MSP430FR6989IPZ - 16-bit ULP FRAM MCU 128KB | TI LQFP-100
MSP430FR6989IPZ

MSP430FR6989IPZ - 16-bit ULP FRAM MCU 128KB | TI LQFP-100

The Texas Instruments MSP430FR6989IPZ is a 16-bit ultra-low-power MSP430 FRAM microcontroller with 128KB of embedded FRAM, an extended scan interface (ESI), hardware AES-128 accelerator, and an integrated LCD driver, housed in a 100-pin LQFP (PZ) package. It operates from a 16 MHz MSP430 CPUXV2 core with a 1.8 V to 3.6 V supply and is rated for the -40 C to +85 C industrial temperature range. An FRAM-based microcontroller is a mixed-signal MCU whose non-volatile memory uses Ferroelectric RAM rather than flash. FRAM delivers nearly unlimited write endurance (roughly 100x more than flash), faster unified-memory writes at low energy, and a simpler software model because code and data share one address space. The MSP430 FRAM platform combines this memory with TI's holistic ultra-low-power system architecture, allowing designers to log data or run frequent writes without the wear-budget anxiety associated with flash. In the broader hierarchy, this device is a microcontroller -> embedded MCU -> mixed-signal SoC -> semiconductor. Key specifications include 128 KB of non-volatile FRAM, 2 KB of information FRAM, 16 KB of SRAM, a 12-bit SAR ADC with up to 16 channels, four 16-bit timers, up to 83 GPIO pins, a real-time clock, and a 320-segment LCD driver. The integrated extended scan interface is purpose-built for liquid flow-meter rotary sensing, while the AES-128 hardware accelerator supports encrypted metering and secure connectivity. The MSP430FR6989IPZ leverages TI's MSP430 CPUXV2 architecture with active current of approximately 118 uA/MHz and standby current under 1 uA with RTC retention, enabling multi-year battery life in metering and sensor applications. The unified FRAM memory can be partitioned at runtime between code and data, simplifying field firmware updates and over-the-air data logging. Built-in BSL and JTAG/SBW interfaces simplify in-system programming. Typical applications include water, heat, and gas flow meters with rotary sensing, portable medical and industrial sensor loggers, secure battery-powered IoT endpoints, e-paper / LCD human-machine interfaces, and energy-harvesting wireless sensor nodes where its ultra-low-power modes and FRAM endurance deliver measurable system-level advantages. When designing with this MCU, allocate the FRAM memory between code and data carefully - because writes are nearly instantaneous and unlimited, data-logging applications can reserve large blocks for circular buffers, but be sure to budget enough FRAM for firmware images so that in-field updates remain possible. This page synthesizes distributor pricing, parametric alternatives, and practical design guidance that are not aggregated on any single manufacturer or distributor datasheet page.

RFQ संपर्क
MSP430FW425IPM - 16-Bit 8MHz Flow-Meter MCU | Texas Instruments
MSP430FW425IPM

MSP430FW425IPM - 16-Bit 8MHz Flow-Meter MCU | Texas Instruments

The Texas Instruments MSP430FW425IPM is a 16-bit mixed-signal microcontroller optimized for electronic flow meters, with an 8 MHz CPU, 16 KB of flash memory, 512 bytes of SRAM, a rotary-sensing scan interface, and a 64-LQFP package measuring 10 mm by 10 mm. It combines embedded control, metering-oriented sensing, and low-power operation in a surface-mount industrial device. A mixed-signal microcontroller is a semiconductor that combines a digital processor with analog and timing peripherals on one integrated circuit. In the product hierarchy, the MSP430FW425IPM belongs to the MSP430 family of 16-bit RISC microcontrollers, placing it between general-purpose embedded controllers and dedicated metering processors. Its scan interface helps acquire position or rotation-related data for flow-meter mechanisms while the CPU handles measurement control, calibration, calculations, and communications. The principal device characteristics include a maximum listed CPU frequency of 8 MHz, 16 KB of flash memory for firmware, and 512 bytes of SRAM for working data. The 64-pin LQFP package provides a practical industrial footprint with enough peripheral connections for sensor inputs, control signals, debug access, and power management. The part is identified specifically for flow-meter applications rather than being a general-purpose performance processor. Its architecture centers on a 16-bit MSP430 CPU optimized for embedded control and low-power operation. Flash memory retains the application firmware across power loss, while SRAM supports runtime variables and measurement processing. The scan interface is the defining functional addition for rotary-sensing applications, reducing the need for separate sensing circuitry when the measured mechanism can be scanned by the MCU. Typical uses include compact ultrasonic flow meters, electromagnetic flow-meter controllers, positive-displacement meter electronics, water and gas metering equipment, and industrial totalizers. The device is especially relevant when a meter requires local signal acquisition, low-power embedded processing, and compact PCB integration without the overhead of a larger application processor. Designers should assign the scan and sensing signals according to the manufacturer pin description table and reserve the exposed resources required for the meter's sensor type. Firmware should include calibration, signal validation, flow-direction handling, and fault detection because metering accuracy depends on both analog timing and the quality of the computed result. This page consolidates the device identity, memory configuration, package information, metering features, sourcing workflow, application guidance, and verified same-family replacement options into one engineering reference. It also distinguishes true drop-in package alternatives from merely similar MSP430 products so procurement and design decisions can be evaluated together.

RFQ संपर्क
MSP430FW427IPM - 16-Bit 8MHz Metering MCU, 64-LQFP | TI
MSP430FW427IPM

MSP430FW427IPM - 16-Bit 8MHz Metering MCU, 64-LQFP | TI

The Texas Instruments MSP430FW427IPM is a 16-bit mixed-signal microcontroller for rotary sensing and metering systems, operating at 8 MHz with 32 KB of Flash memory and 1 KB of SRAM in a 64-pin LQFP package. It integrates three 16-bit sigma-delta ADCs, a 128-segment LCD controller, and a scan interface for gas, water, and electrical metering instruments. A mixed-signal microcontroller combines a digital processor with analog conversion and display resources on one device. The MSP430 CPU16 architecture uses 16-bit registers and constant generators to support compact, energy-efficient code. In the MSP430FW427, these resources are optimized for low-power sensing rather than high-speed general-purpose control, allowing a meter to measure, process, and display information while minimizing energy consumption. Key features include 32 KB of Flash organized as 32K x 8 plus 256 bytes, 1 KB of SRAM, three 16-bit sigma-delta ADC channels, and a 128-segment LCD. The device supports operation from 2.5 V and 3.3 V supply arrangements, making it suitable for battery-operated and mains-referenced metering products. The industrial-grade ordering option supports design work intended for extended industrial environments. The sigma-delta ADC architecture is central to this sensing platform. Its three converters can acquire low-frequency analog signals associated with sensor elements, while the scan interface helps the device interrogate external sensor or switching networks systematically. This combination reduces the need for discrete analog front ends and keeps measurement, control, and display functions within one compact 64-LQFP device. Typical uses include mechanical water meters, rotary flow meters, gas meters, electricity meters, and compact industrial sensing instruments. The LCD controller supports direct segment driving for compact meter displays, while the scan interface accommodates multiplexed sensor arrangements where a rotating or resistive sensing element must be interrogated. When laying out a meter board, keep analog sensor connections short and place their protection or filtering components close to the associated input pins. Confirm the required external crystal, capacitor, LCD, and sensor-network values against the device documentation, and observe the specified operating voltage for the exact ordering option used in production. This page consolidates device specifications, ordering-package details, same-package alternatives, comparison data, and practical design guidance to support component selection and PCB planning for next-generation rotary sensing instruments.

RFQ संपर्क
MSP430G2210ID - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments (Tape & Reel)
MSP430G2210ID

MSP430G2210ID - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430G2210ID is a 16-bit mixed-signal microcontroller from the MSP430G2xx Value-Series, operating at up to 16 MHz with 2 KB Flash and 128 B SRAM, housed in an 8-pin SOIC (D) package. It features an integrated low-power comparator, a 16-bit timer, and four general-purpose I/O pins, making it well-suited for ultra-low-cost embedded applications. The device operates from a 1.8 V to 3.6 V supply and supports ultra-low power consumption across five power-saving modes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O into one package. The MSP430 family specifically uses a 16-bit von Neumann RISC architecture, optimized for ultra-low power operation and mixed-signal applications. Within the broader taxonomy, the MSP430G2xx Value-Series targets cost-sensitive applications that still require the low-power signature of the MSP430 platform, sitting between simple 8-bit MCUs and higher-end ARM Cortex-M0 parts in capability and price. Key features of the MSP430G2210ID include active-mode current of 220 µA at 1 MHz (2.2 V), standby current of 0.5 µA, off-mode RAM retention current of 0.1 µA, and an ultra-fast wake-up from standby mode of less than 1 µs. The integrated brownout detector and on-chip internal oscillator simplify BOM cost by eliminating external clock or voltage supervisor components in cost-sensitive designs. The device is supported by TI's MSP430 LaunchPad ecosystem, free Code Composer Studio IDE, and a broad library of application notes covering ultra-low power design patterns. The MSP430G2210ID uses the MSP430 CPU16 core, which combines a 16-bit RISC instruction set with a 16-bit data path, 16 registers, and a constant generator for maximum code density. Program memory is in-system programmable Flash with 2 KB total (approximately 2K x 8 plus 256 B information memory), and the 128 B RAM supports data and stack operations. The internal digitally-controlled oscillator (DCO) provides the 16 MHz maximum clock without external crystals, and the on-chip comparator can wake the CPU from LPM4 with no external components. Typical applications include battery-powered sensor nodes, smoke detectors, remote controls, smart metering, handheld instruments, toys, and any cost-sensitive embedded system requiring ultra-low standby current. The 8-pin SOIC footprint is friendly for hand-soldering and hobbyist prototyping as well as high-volume SMT manufacturing lines. When designing with this device, ensure the supply voltage stays within 1.8 V to 3.6 V and respect absolute maximum ratings on I/O pins to avoid latch-up. The four GPIO pins are multiplexed with the comparator, timer, and JTAG functions; verify pin allocation against the desired peripheral mix before finalizing the schematic. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers select and source the MSP430G2210ID with full context.

RFQ संपर्क
MSP430G2210IDR - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments
MSP430G2210IDR

MSP430G2210IDR - 16MHz MCU, 2KB Flash, 128B SRAM | Texas Instruments

The Texas Instruments MSP430G2210IDR is a 16-bit mixed-signal microcontroller from the MSP430G2xx Value-Series, operating at up to 16 MHz with 2 KB Flash and 128 B SRAM, housed in an 8-pin SOIC (D) package. It features an integrated low-power comparator, a 16-bit timer, and four general-purpose I/O pins, making it well-suited for ultra-low-cost embedded applications. The device operates from a 1.8 V to 3.6 V supply and supports ultra-low power consumption across five power-saving modes. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O into one package. The MSP430 family specifically uses a 16-bit von Neumann RISC architecture, optimized for ultra-low power operation and mixed-signal applications. Within the broader taxonomy, the MSP430G2xx Value-Series targets cost-sensitive applications that still require the low-power signature of the MSP430 platform, sitting between simple 8-bit MCUs and higher-end ARM Cortex-M0 parts in capability and price. Key features of the MSP430G2210IDR include active-mode current of 220 µA at 1 MHz (2.2 V), standby current of 0.5 µA, off-mode RAM retention current of 0.1 µA, and an ultra-fast wake-up from standby mode of less than 1 µs. The integrated brownout detector and on-chip internal oscillator simplify BOM cost by eliminating external clock or voltage supervisor components in cost-sensitive designs. The device is supported by TI's MSP430 LaunchPad ecosystem, free Code Composer Studio IDE, and a broad library of application notes covering ultra-low power design patterns. The MSP430G2210IDR uses the MSP430 CPU16 core, which combines a 16-bit RISC instruction set with a 16-bit data path, 16 registers, and a constant generator for maximum code density. Program memory is in-system programmable Flash with 2 KB total (approximately 2K x 8 plus 256 B information memory), and the 128 B RAM supports data and stack operations. The internal digitally-controlled oscillator (DCO) provides the 16 MHz maximum clock without external crystals, and the on-chip comparator can wake the CPU from LPM4 with no external components. Typical applications include battery-powered sensor nodes, smoke detectors, remote controls, smart metering, handheld instruments, toys, and any cost-sensitive embedded system requiring ultra-low standby current. The 8-pin SOIC footprint is friendly for hand-soldering and hobbyist prototyping as well as high-volume SMT manufacturing lines. When designing with this device, ensure the supply voltage stays within 1.8 V to 3.6 V and respect absolute maximum ratings on I/O pins to avoid latch-up. The four GPIO pins are multiplexed with the comparator, timer, and JTAG functions; verify pin allocation against the desired peripheral mix before finalizing the schematic. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers select and source the MSP430G2210IDR with full context.

RFQ संपर्क
MSP430G2230ID - 16MHz Low-Power MCU with 10-Bit ADC
MSP430G2230ID

MSP430G2230ID - 16MHz Low-Power MCU with 10-Bit ADC

The Texas Instruments MSP430G2230ID is a 16 MHz mixed-signal microcontroller with 2 KB of Flash memory, 256 bytes of SRAM, and a 10-bit ADC in an 8-pin SOIC package. Its supply range is 1.8 V to 3.6 V, while integrated SPI, I2C, and timer peripherals support compact sensing, control, and communication designs. A mixed-signal microcontroller combines a digital processor with analog measurement and interface functions on one integrated circuit. The MSP430 family belongs to the embedded microcontroller category within integrated circuits. Its 16-bit RISC architecture, 16-bit registers, and low-power operating modes make it suitable for portable measurement and control systems where energy efficiency, deterministic control, and compact peripheral integration are important. Key features include operation up to 16 MHz, 2 KB of Flash program memory, 256 bytes of SRAM, and a 10-bit analog-to-digital converter. The device also provides SPI and I2C communication interfaces, timer resources, and five power-saving modes. Active-mode current is listed as 220 uA at 1 MHz and 2.2 V, while standby current is 0.5 uA and off-mode current with RAM retention is 0.1 uA. The MSP430G2230ID is designed for low-power embedded control. Its 10-bit ADC allows analog sensor signals to be digitized without a separate converter, while SPI and I2C permit connection to external transducers, memory, or remote sensing nodes. The 256-byte SRAM supports small working data sets, and the 2 KB Flash area accommodates compact firmware for dedicated control tasks. Typical uses include portable environmental measurement, battery-powered instrumentation, low-cost sensor nodes, industrial process monitoring, and compact consumer controls. The 8-pin SOIC package also simplifies assembly where a through-hole-compatible surface-mount footprint is preferable to a very small QFN package. When designing the power supply, verify that each rail remains within 1.8 V to 3.6 V and account for the input-voltage range of every attached peripheral. Place the device close to its decoupling network, preserve a short analog-signal path to the ADC input, and follow the recommended external-circuitry and grounding guidance in the manufacturer datasheet. This product summary combines the manufacturer specifications with engineering-focused guidance for low-power firmware development, analog acquisition, serial connectivity, and PCB implementation. It is intended to help engineers identify whether the MSP430G2230ID provides the required memory, conversion capability, interfaces, package, and operating characteristics for a compact embedded design.

RFQ संपर्क
MSP430G2230IDR - 16MHz Mixed-Signal MCU | Texas Instruments
MSP430G2230IDR

MSP430G2230IDR - 16MHz Mixed-Signal MCU | Texas Instruments

The Texas Instruments MSP430G2230IDR is a mixed-signal microcontroller with a 16 MHz MSP430 CPU, 2 KB of Flash program memory, 256 bytes of SRAM, and a 10-bit ADC in an 8-pin SOIC package. It also provides SPI and I2C serial interfaces, timers, four I/O pins, and five low-power modes for compact, low-energy measurement systems. A mixed-signal microcontroller combines a digital microcontroller core with analog measurement and communication peripherals. In the MSP430 family, this integration allows a compact system to sample analog signals, process the measurements, and communicate with sensors or host equipment without requiring several separate devices. The MSP430G2230 is therefore positioned between a general-purpose embedded controller and a dedicated low-power measurement engine. The headline capabilities are a 16 MHz maximum operating frequency, 2 KB of Flash memory, and 256 bytes of SRAM. Its 10-bit ADC supports embedded analog measurements, while SPI and I2C provide two common paths for connecting serial peripherals. Four I/O pins make the device particularly appropriate for small systems whose external interface needs remain modest. The manufacturer describes five low-power operating modes that are optimized for extended battery life in portable measurement applications. At the architectural level, the MSP430G2230 uses a 16-bit RISC CPU with 16-bit registers. The product page highlights the architecture, register width, and low-power design as the basis for its portable-measurement positioning. The device can execute code from its internal Flash memory and retain working data in SRAM, while the integrated analog and serial peripherals reduce the need for separate support chips. Typical applications include battery-powered sensor nodes, compact industrial measurement instruments, portable data loggers, digital thermometers, and low-power monitoring devices. SPI or I2C can connect an external sensor or transceiver, while the ADC can acquire an analog input from a resistive bridge, thermistor, or other transducer. The limited 2 KB program-memory capacity favors compact firmware with tight peripheral control. PCB implementation requires careful attention to the 8-pin SOIC footprint, exposed pad-free thermal behavior, decoupling, and the device's low-voltage supply limits. Place the supply and ground connections directly to the relevant pins, keep analog input routing away from fast digital transitions, and confirm all operating conditions against the manufacturer datasheet before release. This page combines the manufacturer's device overview, exact ordering information, package identification, interface details, and practical selection guidance. It also distinguishes verified device capabilities from replacement questions so engineers can assess fit, memory limits, package compatibility, and low-power operation before committing to a design.

RFQ संपर्क
MSP430G2553CY - 16MHz 16KB Flash Mixed-Signal MCU | TI
MSP430G2553CY

MSP430G2553CY - 16MHz 16KB Flash Mixed-Signal MCU | TI

Texas Instruments MSP430G2553CY is a 16-bit mixed-signal microcontroller operating at 16 MHz, with 16 KB of Flash memory and 512 bytes of SRAM. The device combines a comparator, timers, UART, SPI, and I2C interfaces in a 32-pin QFN package. The supplied ordering information identifies this orderable MPN as a die-sale device, so package-specific mechanical details and production procurement terms must be confirmed with TI before assembly. A mixed-signal microcontroller is an embedded semiconductor that combines a programmable digital controller with analog or sensing functions. In the product hierarchy, this MSP430 belongs to the microcontroller, embedded processor, semiconductor, and mixed-signal controller classes. Its 16-bit MSP430 CPU architecture makes it suitable for compact control systems requiring low power, deterministic peripheral access, and several communication interfaces without a separate analog processor. The verified device information identifies a 16 MHz operating speed, 16 KB Flash, 512 B SRAM, one comparator, UART/SPI/I2C connectivity, and timers. DigChip additionally lists 24 I/O ports, a 3.3 V to 3.6 V supply range, and a 0.1 µA off-mode current with RAM retention. These figures position MSP430G2553CY for low-power sensing, control, instrumentation, and communications designs where memory and integrated interfaces are more important than high-speed digital processing. The MSP430G2xx family architecture is oriented toward low-power embedded control. Its integrated comparator supports threshold-based sensing, while UART, SPI, and I2C support connections to sensors, displays, transceivers, and external nonvolatile memory. The timer resources can provide event timing and periodic service functions, but individual timer channels, capture/compare resources, and interrupt assignments must be selected from the MSP430G2x53 datasheet for the exact die. Typical applications include battery-powered sensor nodes, compact industrial monitors, digital thermometers, environmental measurement systems, motor or actuator controllers, and simple serial gateways. For a new PCB, the CY suffix and die-sale status require careful review: developers should not assume that the QFN-32 package information found in generic listings corresponds to the CY deliverable. Board assembly may instead require the documented die-sale process, bonding method, and package outline. Before layout, confirm the exact pin assignment and exposed-pad requirements in the official MSP430G2x53 datasheet and with TI. Program development commonly uses an MSP430-compatible toolchain, but the verified data does not identify a specific IDE version, debugger, or programming adapter. Power, ground, decoupling, reset, boot-strapping, communication, and exposed-pad connections should therefore follow the authoritative device documentation rather than generic QFN assumptions. This page consolidates verified manufacturer and distributor information, separates die-sale ordering facts from generic family specifications, and identifies unresolved package, pricing, pinout, lifecycle, and compliance details instead of guessing. It is intended as an engineering-data starting point for MSP430G2553CY sourcing and design review, not as a substitute for TI's final orderable datasheet and quality documentation.

RFQ संपर्क
MSP430G2553IN20 - 16MHz 16KB Flash MCU | Texas Instruments
MSP430G2553IN20

MSP430G2553IN20 - 16MHz 16KB Flash MCU | Texas Instruments

The Texas Instruments MSP430G2553IN20 is a 16 MHz mixed-signal microcontroller with a 16-bit RISC CPU, 16 KB of Flash memory, 512 bytes of SRAM, and integrated analog and serial peripherals in a 20-pin PDIP package. Its operating temperature range is -40°C to 85°C. The device combines five low-power modes with a 10-bit ADC and comparator for portable measurement and embedded control designs. A mixed-signal microcontroller combines a digital processor, analog measurement circuitry, communications interfaces, and timing resources within one device. The MSP430G2553 belongs to the MSP430 family of ultra-low-power microcontrollers and targets applications that require deterministic control, efficient peripheral integration, and low standby consumption. Its architecture supports portable instruments, sensing nodes, data acquisition modules, and small embedded-control systems. Key features include a 16-bit RISC CPU operating at up to 16 MHz, 16 KB of Flash, 512 bytes of SRAM, a 10-bit ADC, an analog comparator, UART, SPI, I²C, and timers. The integrated peripherals reduce external component count and allow compact designs that measure analog inputs while exchanging data with external sensors, displays, or host systems. The manufacturer identifies the device for low-power portable measurement applications. The MSP430 architecture uses 16-bit registers and an interrupt-oriented peripheral model. Its mixed-signal resources support sensor conditioning and threshold comparison without requiring a separate analog processor, while UART, SPI, and I²C interfaces provide paths to external integrated circuits. The 20-pin PDIP package also exposes the device through a conventional through-hole footprint suitable for prototyping, education, and industrial control boards. Typical uses include battery-powered measurement instruments, simple data loggers, environmental sensors, industrial sensing nodes, keypad interfaces, and compact embedded-control products. UART, SPI, or I²C can connect a sensor module or local display, while the ADC and comparator support analog measurement. The MSP430G2553IN20 is also widely used as the target device for MSP430 LaunchPad-style development and educational projects. Designers should verify the exact pin functions and peripheral multiplexing against the manufacturer datasheet before laying out the PCB. Decoupling, grounding, unused-pin handling, clock configuration, and low-power mode sequencing are critical in a compact mixed-signal design. The verified data does not provide a complete pin-level mapping, so pin names and electrical details not explicitly supplied are marked as needed rather than inferred.

RFQ संपर्क
MSP430G2553IPW0RQ1 - 16MHz Automotive MCU | Texas Instruments
MSP430G2553IPW0RQ1

MSP430G2553IPW0RQ1 - 16MHz Automotive MCU | Texas Instruments

The Texas Instruments MSP430G2553IPW0RQ1 is an automotive 16-bit mixed-signal microcontroller operating at 16 MHz, with 16 KB of Flash memory, 512 B of SRAM, and a 10-bit ADC. It is supplied in a 20-pin TSSOP (PW) package rated for -40°C to +85°C and integrates UART, SPI, I²C, timer, and comparator peripherals. A mixed-signal microcontroller is a semiconductor device that combines a programmable digital controller with analog measurement or signal-conditioning resources. The MSP430 belongs to the MCU → microcontroller → embedded processor → semiconductor hierarchy and is designed for compact, low-power control systems. Its 16-bit CPU16 architecture, on-chip memory, and communication peripherals allow standalone sensing and control without requiring separate memory, ADC, or serial-interface devices. Key device resources include a 16 MHz maximum clock, 16 KB of Flash program memory, 512 B of SRAM, a 10-bit analog-to-digital converter, and an integrated comparator. The MCU supports UART, SPI, and I²C communication, while timer resources support periodic measurement, timing, and control functions. The -40°C to +85°C operating range and automotive qualification make the Q1 device suitable for demanding vehicle electronic modules. The MSP430G2 family architecture combines compact digital processing with mixed-signal measurement. Flash memory retains programmed firmware across power removal, while SRAM supports working variables and stack operations. The ADC provides an integrated path for analog inputs, and the comparator can support threshold detection or basic signal monitoring. Serial interfaces allow the device to communicate with sensors, transceivers, memories, and external controllers. Typical uses include automotive body and sensing modules, battery-powered instrumentation, condition-monitoring controllers, compact data loggers, and low-power industrial controls. The device is especially appropriate where a small TSSOP footprint, mixed-signal integration, and multiple serial interfaces are more valuable than a high-pin-count application processor. Designers should preserve the power, ground, and decoupling layout recommended by the MSP430G2553-Q1 datasheet and verify unused I/O states in the final design. Because automotive qualification, operating-temperature grade, and ordering suffix affect procurement, replacements should be checked for identical package pinout, 16 MHz operation, memory capacity, ADC resolution, and peripheral configuration before substitution. This product page consolidates the verified manufacturer and distributor information for MSP430G2553IPW0RQ1, including package and memory details, current purchasing data, drop-in replacement guidance, comparison parameters, and practical design considerations.

RFQ संपर्क
MSP430G2553IPW20 - 16MHz 16KB MCU | Texas Instruments
MSP430G2553IPW20

MSP430G2553IPW20 - 16MHz 16KB MCU | Texas Instruments

The Texas Instruments MSP430G2553IPW20 is a 16-bit mixed-signal microcontroller operating at up to 16 MHz, with 16 KB of Flash memory, 512 bytes of SRAM, and a 20-pin TSSOP (PW) package. According to the Texas Instruments product page, the device includes comparator, UART, SPI, I2C, and timer resources for compact embedded control designs. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, input/output ports, and peripherals into one device. The MSP430 belongs to the mixed-signal MCU family, combining digital control with analog comparison capability and low-power operating modes. This makes it useful for embedded products that must measure a signal, control peripherals, communicate with external systems, or operate from limited power budgets. The MSP430G2553IPW20 provides 16 KB of Flash for firmware, 512 bytes of SRAM for working data, and a maximum clock frequency of 16 MHz. Its listed peripherals include a comparator, UART, SPI, I2C, and timer. The supplied distributor and manufacturer snippets identify the industrial temperature range as -40 °C to +85 °C and the package as 20-pin TSSOP (PW). The verified source data does not provide the complete pin-level electrical table, so individual pin functions and several operating-current values remain unverified. The MSP430G2553 platform is suited to low-power embedded control, sensor conditioning, communication bridges, and small control nodes. The comparator can support threshold-based analog supervision, while the serial interfaces allow connection to displays, sensors, transceivers, or storage devices. The 16 MHz CPU class is appropriate for event handling, protocol management, and control logic where deterministic behavior is more important than workstation-class processing. When designing a board around this MCU, verify the device pinout and the detailed electrical limits in the manufacturer datasheet before routing power, programming signals, communication interfaces, and analog inputs. Pay particular attention to decoupling, oscillator configuration, unused pins, programming access, and the selected supply voltage. Firmware and peripheral assignments should also be checked against the exact device variant and package. This page combines the verified Texas Instruments product information with distributor references, application guidance, and procurement considerations. It is intended to help engineers identify the correct MSP430G2553IPW20 for low-power embedded systems while clearly separating confirmed specifications from parameters that still require datasheet confirmation.

RFQ संपर्क
MSP430G2553IPW20R - 16MHz 16KB MCU | Texas Instruments (Tape & Reel)
MSP430G2553IPW20R

MSP430G2553IPW20R - 16MHz 16KB MCU | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430G2553IPW20R is a 16-bit mixed-signal microcontroller operating at up to 16 MHz, with 16 KB of Flash memory, 512 bytes of SRAM, and a 20-pin TSSOP (PW) package. According to the Texas Instruments product page, the device includes comparator, UART, SPI, I2C, and timer resources for compact embedded control designs. A microcontroller is a programmable semiconductor that integrates a CPU core, memory, input/output ports, and peripherals into one device. The MSP430 belongs to the mixed-signal MCU family, combining digital control with analog comparison capability and low-power operating modes. This makes it useful for embedded products that must measure a signal, control peripherals, communicate with external systems, or operate from limited power budgets. The MSP430G2553IPW20R provides 16 KB of Flash for firmware, 512 bytes of SRAM for working data, and a maximum clock frequency of 16 MHz. Its listed peripherals include a comparator, UART, SPI, I2C, and timer. The supplied distributor and manufacturer snippets identify the industrial temperature range as -40 °C to +85 °C and the package as 20-pin TSSOP (PW). The verified source data does not provide the complete pin-level electrical table, so individual pin functions and several operating-current values remain unverified. The MSP430G2553 platform is suited to low-power embedded control, sensor conditioning, communication bridges, and small control nodes. The comparator can support threshold-based analog supervision, while the serial interfaces allow connection to displays, sensors, transceivers, or storage devices. The 16 MHz CPU class is appropriate for event handling, protocol management, and control logic where deterministic behavior is more important than workstation-class processing. When designing a board around this MCU, verify the device pinout and the detailed electrical limits in the manufacturer datasheet before routing power, programming signals, communication interfaces, and analog inputs. Pay particular attention to decoupling, oscillator configuration, unused pins, programming access, and the selected supply voltage. Firmware and peripheral assignments should also be checked against the exact device variant and package. This page combines the verified Texas Instruments product information with distributor references, application guidance, and procurement considerations. It is intended to help engineers identify the correct MSP430G2553IPW20R for low-power embedded systems while clearly separating confirmed specifications from parameters that still require datasheet confirmation.

RFQ संपर्क
MSP430G2553IPW28 - 16MHz 16KB Flash MCU | Texas Instruments (Tape & Reel)
MSP430G2553IPW28

MSP430G2553IPW28 - 16MHz 16KB Flash MCU | Texas Instruments (Tape & Reel)

The Texas Instruments MSP430G2553IPW28 is a 16-bit ultra-low-power mixed-signal microcontroller from the MSP430 Value Line series, featuring a 16MHz CPU, 16KB Flash, 512B SRAM, and a rich set of integrated peripherals. Housed in a 28-pin TSSOP (PW) package, it operates from 1.8V to 3.6V over the industrial temperature range of -40 to +85 C. A microcontroller (MCU) is a compact integrated circuit that governs a specific operation in an embedded system, containing a processor core, memory (Flash and SRAM), and programmable I/O peripherals. The MSP430 family sits within the broader hierarchy of 16-bit RISC microcontrollers under power-management-conscious embedded processing, and is renowned for five low-power modes (LPM0 to LPM4) that reduce current to as low as 0.1 uA in standby mode with RAM retention. Key features include a 10-bit ADC, an analog comparator, two 16-bit timers, and a universal serial communication interface (USCI) supporting UART, SPI, and I2C. The device integrates a temperature sensor, brownout reset, and capacitive-touch-enabled I/O. Its internal DCO is factory-calibrated to 16 MHz with approximately 1% accuracy, often eliminating external crystals. Architecturally, the MSP430G2553 uses a 16-bit RISC CPU with a von-Neumann memory map, enabling efficient code density and rapid wake-up from low-power modes. Firmware can be updated in-system via the two-wire Spy-Bi-Wire interface, simplifying production programming. Typical applications include portable medical devices, wireless sensor nodes, smart meters, remote controls, and battery-powered consumer electronics. The 16KB Flash accommodates substantial application code, while 512B SRAM supports moderate buffering. The integrated comparator and ADC enable direct sensor interfacing, and the multiple communication interfaces allow easy connectivity to radios, displays, and other peripherals. Design tip: place a 0.1 uF capacitor close to DVCC and 1 uF at the power entry; configure unused I/O as outputs to avoid floating-input leakage. This mature, widely available part has extensive community support for both prototyping and production. The MSP430G2553IPW28 is a popular choice for cost-sensitive, power-critical designs where performance and low energy consumption are paramount.

USD $0.72 संपर्क