उत्पाद (46,000+)

TJA1051T/CM - 5Mbit/s High-Speed CAN Transceiver | NXP
TJA1051T/CM

TJA1051T/CM - 5Mbit/s High-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1051T/CM is a high-speed CAN transceiver with a 5 Mbit/s data rate, designed to connect a CAN protocol controller to a two-wire CAN bus. It is supplied in an 8-pin SOIC surface-mount package for compact automotive and industrial control electronics. The device provides differential transmit and receive functions while placing the CAN physical-layer interface close to the host processor or microcontroller. A CAN transceiver is an interface IC within the Controller Area Network hierarchy. It converts logic-level TXD and RXD signals into the dominant and recessive voltage levels used by a wired CAN network, while also receiving bus information for the controller. The TJA1051T/CM therefore connects a digital CAN controller to the physical wiring of a multi-node vehicle, industrial machine, or embedded communications system without requiring the controller to handle the bus electrical layer directly. The TJA1051 family is identified by NXP as a third-generation high-speed CAN transceiver with enhanced electromagnetic compatibility performance. Its 5 Mbit/s capability supports data transfer rates commonly required by automotive body, chassis, comfort, and controller-area-network systems. Differential bus signaling helps reject common-mode noise, while the dedicated TXD and RXD paths provide a clear separation between commands sent to the bus and data returned to the CAN controller. The eight-pin SOIC package supports compact surface-mount assembly and exposes the CANH and CANL bus terminals, VCC, ground connections, TXD, and RXD. This arrangement allows the transceiver to be placed close to the bus connector and controller, reducing the distance over which sensitive signals and supply connections must travel. Exact operating voltage, ESD ratings, standby behavior, and temperature limits should be confirmed in the manufacturer datasheet before final circuit release. Typical uses include automotive CAN gateways, body-control modules, electric-window and seating controllers, industrial automation equipment, sensors, and embedded diagnostic systems. In each application, the CAN controller handles frame construction, arbitration, acknowledgments, and higher-level protocols, while the TJA1051T/CM handles the physical-layer voltage conversion and bus-interface function. This division allows the host processor to work with ordinary digital logic while multiple nodes communicate over a shared two-wire network. PCB design should prioritize short CANH and CANL routes, a compact common return path, and placement of the transceiver close to the bus connector. The bus-side network also needs termination, filtering, and protection suited to the vehicle or industrial environment. Validate the complete channel against EMC, ESD, ground-offset, and fault-recovery requirements rather than relying on general transceiver ratings alone. This page combines the manufacturer's product description, exact package identification, verified sourcing references, and practical guidance for comparing, sourcing, and integrating the TJA1051T/CM. It also highlights the engineering boundaries that must be checked in the datasheet before using a similarly packaged CAN transceiver as a drop-in replacement.

RFQ संपर्क
TJA1051T/E - High-Speed CAN Transceiver in SOIC-8 | NXP
TJA1051T/E

TJA1051T/E - High-Speed CAN Transceiver in SOIC-8 | NXP

NXP Semiconductors TJA1051T/E is a high-speed CAN transceiver that interfaces a Controller Area Network controller with a physical two-wire CAN bus. It provides differential transmit and receive capabilities in an 8-pin SOIC package and includes an enable input for low-current control. The device is designed for automotive systems requiring reliable high-speed CAN communication, improved electromagnetic compatibility, and electrostatic-discharge resilience. Its 3.3 V to 5 V logic compatibility and passive behavior when unpowered make it suitable for interface isolation. A CAN transceiver is the physical-layer component between a digital CAN controller and a two-wire differential network. The TJA1051T/E converts controller logic into CANH and CANL bus signals and converts differential bus voltages into a receive signal for the controller. It belongs to the CAN physical-layer transceiver hierarchy within interface ICs, where controllers implement the data-link protocol and transceivers handle electrical signaling, bus dominance, fault tolerance, and electromagnetic behavior. The TJA1051 is described by NXP as a third-generation high-speed CAN transceiver. Its principal features include differential transmission and reception, an enable input, enhanced electromagnetic compatibility, and electrostatic-discharge protection. The TJA1051T/E ordering variant uses the SOIC-8 package, while the TJA1051T/3 variant provides a VIO connection for direct interfacing with 3 V to 5 V microcontrollers. Circuit designs must therefore verify the function and electrical level of pin 5 for the selected orderable variant rather than treating every TJA1051 suffix as interchangeable. The transceiver operates in automotive and industrial environments where the CAN bus must maintain signal integrity through wiring, connectors, common-mode voltage excursions, and electromagnetic interference. Its low electromagnetic emission and high immunity characteristics help reduce interference with neighboring electronic systems. The enable function permits the host microcontroller to place the transceiver into a low-current state when it is not needed, supporting power management and fault-isolation strategies. Typical uses include vehicle body-control modules, engine controllers, gateways, instrumentation, industrial automation controllers, diagnostic equipment, and embedded CAN networks. In these systems, the TJA1051T/E works with a CAN protocol controller rather than replacing the controller itself. The controller generates and interprets CAN frames, while the transceiver conditions the physical bus signals and provides bus-fault protection at the interface boundary. Designers should use the manufacturer's pin-description and application information when assigning PCB tracks, especially for pin 5 on the TJA1051T/E enable variant. CANH and CANL require the correct bus termination, common-mode choke, protection network, and routing geometry. Supply and ground connections should be decoupled close to the device, and the bus interface should be checked against the required common-mode range, transient immunity, and maximum data rate. This product record combines NXP device positioning, verified distributor identification, SOIC-8 package information, a strict drop-in comparison set, and practical CAN-interface design guidance. It also distinguishes electrical substitution from a true PCB-level replacement by highlighting the enable-versus-VIO issue that affects several superficially similar TJA1051 variants.

RFQ संपर्क
TJA1051T/E/1J - 5Mbit/s CAN Transceiver | NXP Semiconductors
TJA1051T/E/1J

TJA1051T/E/1J - 5Mbit/s CAN Transceiver | NXP Semiconductors

The NXP Semiconductors TJA1051T/E/1J is a high-speed CAN transceiver with a maximum data rate of 5Mbit/s, differential transmit and receive capability, Silent mode, Off mode, and an 8-pin SOIC package. It provides the physical-layer interface between a CAN protocol controller and a two-wire automotive CAN bus. A CAN transceiver is an interface IC within the broader hierarchy of CAN interface ICs, network interface devices, interface integrated circuits, and semiconductors. It converts logic-level TXD and RXD signals from a CAN controller into the balanced differential signaling used on a CAN bus, while converting received bus levels back into a controller-compatible RXD signal. The TJA1051T/E/1J is intended for high-speed CAN systems in automotive and industrial environments. The verified product information identifies support for data rates up to 5Mbit/s, Silent mode, and Off mode. Silent mode can place a node into a state that does not actively drive the bus while retaining the ability to receive according to the device behavior. Off mode provides a very low-current shutdown state. The TJA1051T/E family is also identified as backwards compatible with the TJA1050, which is important for designs migrating from that established high-speed CAN transceiver. The TJA1051T/E/1J is the SOIC-8 version of the third-generation TJA1051 family. NXP describes the TJA1051 as a high-speed CAN transceiver for automotive applications with enhanced electromagnetic compatibility and electrostatic-discharge protection. The differential bus interface reduces susceptibility to common-mode noise, while the transceiver's transmit and receive stages provide the physical signaling required for reliable communication over long, multiconductor harnesses. Typical uses include automotive body-control modules, powertrain controllers, instrument clusters, electronic control units, industrial automation equipment, robotics controllers, and CAN-based sensors. A CAN controller supplies the TXD input and receives RXD, while the TJA1051T/E/1J connects those digital signals to the CANH and CANL bus conductors. The bus must also include the appropriate termination network, decoupling, and protection arrangement specified by the manufacturer. A critical design consideration is the difference between TJA1051T/E/1J and TJA1051T/3/1J. The verified NXP information specifically associates direct interfacing with 3V microcontrollers with the TJA1051T/3 and TJA1051TK/3 variants, not the standard TJA1051T/E/1J. The enable and logic-level behavior should therefore be checked against the controller supply voltage and the existing PCB before substitution. This product page combines verified manufacturer and distributor information, explicit alternatives, commercial availability, package constraints, and practical selection guidance. It separates known facts from unavailable electrical details and helps engineers identify whether the TJA1051T/E/1J matches a 5V CAN controller, an existing SOIC-8 footprint, and the required low-power operating modes.

RFQ संपर्क
TJA1051TK/3/1J - 1 Mbps CAN Transceiver | NXP | 8-HVSON
TJA1051TK/3/1J

TJA1051TK/3/1J - 1 Mbps CAN Transceiver | NXP | 8-HVSON

The NXP Semiconductors TJA1051TK/3/1J is a third-generation high-speed CAN transceiver with a maximum data rate of 1 Mbps, a 4.5 V to 5.5 V transceiver supply range, and direct interfacing for 3 V to 5 V microcontrollers. The device is packaged in an 8-HVSON package measuring 3 mm by 3 mm. A CAN transceiver is the physical-layer interface between a CAN protocol controller and a two-wire CAN bus. It converts the controller's TXD and RXD signals into the differential CANH and CANL bus waveform and converts received bus levels back into a logic signal. Positioned within the interface-IC hierarchy, the TJA1051TK/3/1J connects a digital controller to a differential, noise-prone vehicle or industrial communication network. Key features include enhanced electromagnetic compatibility and electrostatic-discharge performance relative to earlier CAN-transceiver generations. Selected TJA1051TK/3 variants also support VIO-level adaptation for direct connection to 3 V and 5 V microcontrollers. The transceiver exhibits passive behavior when unpowered, disengages from the bus with zero bus load, and supports predictable functional behavior across supply conditions. The /1 version designation identifies a dual-fab-sourced configuration, helping reduce supply-chain risk without changing the electrical specification. The TJA1051 architecture provides differential transmit and receive functions for reliable high-speed CAN communication. Separate transceiver and logic-side supply domains allow VIO to match the controller's operating voltage while VCC supports the CAN transceiver supply. Its 3 mm by 3 mm HVSON package reduces board area compared with larger SOIC implementations, making the device suitable for compact automotive and industrial control electronics. Typical applications include automotive CAN networks, industrial automation controllers, building automation equipment, embedded motor-control systems, and CAN-connected sensor nodes. At the PCB level, the device requires short CANH and CANL routing, a controlled return path, and placement close to the bus connector or transceiver termination network. The controller interface must also observe the input thresholds and timing specified by NXP. For a new design, connect VIO to the microcontroller supply, place the manufacturer-recommended bypass capacitance close to VCC and VIO, and verify termination at both ends of the CAN bus. Confirm the 3 V to 5 V controller compatibility, 1 Mbps maximum data rate, EMC requirements, and exposed-pad thermal design before releasing the PCB. This page combines the manufacturer datasheet, product-page information, package details, procurement data, and engineering guidance to support component selection, pin assignment, PCB implementation, and sourcing of the exact TJA1051TK/3/1J ordering code.

RFQ संपर्क
TJA1052IT - Isolated High-Speed CAN Transceiver SOIC-16 | NXP
TJA1052IT

TJA1052IT - Isolated High-Speed CAN Transceiver SOIC-16 | NXP

The NXP TJA1052IT is a galvanically isolated high-speed CAN transceiver that provides a robust interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SO package and specifically targeted at Electric Vehicle (EV) and Hybrid Electric Vehicle (HEV) applications. An isolated CAN transceiver is a specialized interface IC that combines a high-speed CAN physical layer with on-chip galvanic isolation, typically using integrated coreless transformer or silicon-dioxide (SiO2) dielectric barriers to withstand high common-mode transients in automotive high-voltage environments. Within the broader semiconductor taxonomy, the TJA1052IT sits in the hierarchy isolated CAN transceiver -> CAN transceiver -> CAN interface IC -> automotive interface IC -> power management & signaling semiconductor. Isolation eliminates ground loops between the low-voltage domain (MCU/host) and the high-voltage CAN bus, which is essential when the ECU and chassis sit at different potentials. Key specifications include integrated galvanic isolation rated to withstand high common-mode voltages, support for CAN data rates up to 1 Mbit/s per ISO 11898-2, a wide supply range on the bus side, and very low loop delay suitable for time-triggered CAN (CAN FD-ready) networks. The 16-pin SO package exposes dedicated pins for VCC (logic-side supply), VBUS (bus-side supply), TXD, RXD, CANH, CANL, and the integrated isolation barrier. Architecturally, the TJA1052IT integrates a digital isolator and a CAN transceiver die, with the isolation barrier providing reinforced insulation. This monolithic approach reduces PCB area versus a discrete transceiver + digital isolator solution and improves reliability by eliminating intermediate interconnects. Typical applications include EV/HEV battery management systems, on-board chargers (OBC), DC fast-charging communication links (ISO 15118 PLC not included), traction inverter CAN nodes, and industrial CAN networks requiring reinforced isolation. When designing with the TJA1052IT, place decoupling capacitors close to both VCC and VBUS pins and respect the creepage/clearance rules on the PCB around pins straddling the isolation domain. The device is drop-in compatible with the TI ISO1042 in 16-SO footprint, simplifying second-source strategies. This page synthesizes distributor pricing, drop-in alternatives, and design notes for the TJA1052IT that are not always presented together in the manufacturer datasheet.

RFQ संपर्क
TJA1052IT-1Y - Galvanically Isolated HS CAN Transceiver | NXP
TJA1052IT-1Y

TJA1052IT-1Y - Galvanically Isolated HS CAN Transceiver | NXP

The NXP Semiconductors TJA1052IT-1Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver housed in a 16-pin Small Outline (SO-16) package. It provides an isolated interface between a CAN protocol controller and the physical two-wire differential CAN bus, integrating on-chip galvanic isolation that traditionally required a separate digital isolator plus a CAN transceiver. The part is specifically targeted at Electric Vehicles (EV) and Hybrid Electric Vehicles (HEV), where robust isolation between high-voltage traction domains and low-voltage ECU communication is mandatory. A CAN transceiver is the physical-layer bridge inside an in-vehicle network: it converts the differential logic-level signals from a CAN controller (TXD, RXD) into the bus-side differential voltage on the CANH and CANL lines that meet ISO 11898-2/-5, while protecting the host controller from bus-level transients. The TJA1052i family adds integrated digital isolation (typically using on-chip coreless transformer technology) to that bridge, replacing a two-chip solution (isolator + transceiver) with a single component and simplifying PCB layout while improving common-mode transient immunity (CMTI) in motor-drive environments. Key features include ISO 11898-2/-5 compliant high-speed CAN data rates up to 1 Mbit/s, integrated galvanic isolation rated for 1 kV (digital isolator channel rating per the part classification), tight loop delay for time-triggered CAN (TTCAN) operation, and integrated bus-side protection for harsh automotive electrical environments. The TJA1052i is designed to operate over the full automotive temperature range and supports low-power standby modes for battery-friendly quiescent current draw when the bus is silent. The architecture uses NXP's high-speed CAN transceiver core combined with on-chip galvanic isolation cells, removing the need for external optocouplers or digital isolator ICs while providing the same reinforced isolation barrier between the CAN controller domain and the bus domain. This two-domain split is essential in EV/HEV powertrain ECUs where the bus may sit on a high-voltage referenced plane. Typical applications include EV and HEV battery management system (BMS) CAN nodes, onboard chargers, DC-DC converter telemetry, electric power steering (EPS) communication links, and industrial CAN-isolated gateways that must bridge different ground domains. Designers use the TJA1052IT-1Y where ISO 11898 bus timing must be preserved across an isolation barrier without adding a discrete isolator stage. A key design consideration is that the bus-side and logic-side grounds must remain galvanically separate; do not bypass the isolation by shorting the two ground planes. Also confirm the 1 kV channel rating meets the end-application's reinforced or basic isolation requirement before reuse in higher-voltage systems. This page synthesizes the NXP datasheet, current distributor pricing, and a curated set of drop-in alternatives that share the same SO-16 footprint - content not aggregated on any single manufacturer or distributor page.

RFQ संपर्क
TJA1052IT-5Y - Isolated High-Speed CAN Transceiver 5Mbps AEC-Q100 | NXP
TJA1052IT-5Y

TJA1052IT-5Y - Isolated High-Speed CAN Transceiver 5Mbps AEC-Q100 | NXP

The NXP TJA1052IT-5Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver that provides a 5 Mbps interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SOIC package with 5 kV RMS isolation. It targets Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), and any application requiring reinforced isolation between bus nodes. The integrated digital isolator and CAN transceiver in one package eliminates the need for a discrete isolator plus discrete transceiver, cutting board area roughly in half and simplifying EMC design. A CAN transceiver is a physical-layer (PHY) device that converts differential CAN logic levels from a microcontroller's CAN controller into the dominant/recessive bus signaling required by ISO 11898-2, while providing bus-side fault protection and EMC robustness. The TJA1052IT specifically adds on-chip galvanic isolation - replacing a two-chip solution (isolator + CAN transceiver) with a single device - and is part of the broader hierarchy: CAN transceiver -> interface IC -> integrated circuit. Key features include data rates up to 5 Mbps (CAN FD capable), an isolation voltage of 5000 V RMS for 1 minute per UL 1577, bus fault protection from -27V to +40V, an operating supply range that supports both 1.8V/3.3V/5V MCU sides, and AEC-Q100 qualification for automotive environments. A low-power standby mode with bus wake-up detection is also present, achieved through a dedicated STBY pin and a remote wake-up pattern recognizer compliant with ISO 11898-5. The TJA1052IT uses NXP's integrated capacitive-coupled isolation technology plus a proven CAN PHY, achieving low loop delay under 200 ns - critical for CAN FD frames at the maximum payload phase. Compared with discrete optocoupler + CAN transceiver solutions, the integrated approach reduces propagation delay variation over temperature by a factor of 2-3, improving timing margin in large or noisy automotive networks. Typical applications include EV/HEV battery management system (BMS) bus isolation, OBC (on-board charger) to VCU communication, industrial CAN bus nodes requiring 5 kV isolation (solar inverters, motor drives), EV charging stations with isolated CAN, isolated industrial sensor hubs, and automotive ECU-to-ECU isolation. A key design consideration is the supply topology: the device has two VCC rails - VCC1 (logic/microcontroller side, 2.5V-5.5V) and VCC2 (bus-side, 4.5V-5.5V) - each requiring local decoupling. Designers should follow NXP application note AN11253 for PCB layout, especially maintaining a creepage/clearance margin under the isolation barrier. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, including structured comparison with the TI ISO1042DW as identified in NXP community threads.

RFQ संपर्क
TJA1052IT/2518 - Isolated High-Speed CAN Transceiver | NXP
TJA1052IT/2518

TJA1052IT/2518 - Isolated High-Speed CAN Transceiver | NXP

NXP Semiconductors TJA1052IT/2518 is a galvanically isolated, high-speed Controller Area Network transceiver in a 16-pin SO package. It provides the physical-layer interface between a CAN protocol controller and the two-wire CAN bus, with isolation intended to separate high-voltage and low-voltage portions of electric-vehicle and hybrid-electric-vehicle systems. A CAN transceiver is an interface IC within the broader controller-area network communication hierarchy. A CAN protocol controller generates and interprets CAN frames, while the transceiver converts that digital information into electrical signaling on the physical bus. Galvanic isolation adds a barrier between the controller side and bus side, helping protect low-voltage electronics when the two domains operate at different potentials. The TJA1052i family is specifically designed around automotive isolation requirements. Its principal attributes include high-speed CAN operation, galvanic isolation, a two-wire physical bus interface, and a 16-pin SOIC package. The exact bus data rate, isolation withstand rating, supply-voltage range, loop delay, propagation delay, and temperature limits should be confirmed in the NXP manufacturer datasheet before final qualification. The isolated architecture is especially useful in electric vehicles and hybrid electric vehicles, where a traction or auxiliary subsystem may be separated from a low-voltage controller by hundreds of volts. Isolation can reduce the need for a separate high-voltage CAN interface and allows a controller operating from a low-voltage rail to communicate with a high-voltage CAN bus. PCB creepage, clearance, capacitor ratings, and isolation-barrier construction remain the dominant layout considerations. Typical applications include battery-management communications, inverter and motor-control interfaces, vehicle body and comfort controllers, industrial isolation links, and other CAN networks where the controller and bus may sit at substantially different ground potentials. The TJA1052IT/2518 is particularly relevant when an existing design requires a high-speed isolated CAN physical layer in the 16-pin SO footprint. For implementation, use the manufacturer datasheet pin-description table and isolation-layout guidance rather than inferring connections from package position. Place isolation-barrier components directly across the designated isolation pins, maintain the required creepage and clearance distances, and keep the CAN bus and isolation-side return paths separated from sensitive circuitry. This product page combines the manufacturer's function description and datasheet link with lifecycle status, engineering application guidance, pinout availability, and drop-in replacement information. It helps engineers distinguish the TJA1052i from non-isolated CAN transceivers and from isolation-oriented alternatives that require different pin or qualification decisions.

RFQ संपर्क
TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP
TJA1052IT-2Y

TJA1052IT/2Y - Isolated High-Speed CAN Transceiver | NXP

The NXP TJA1052IT/2Y is a galvanically isolated high-speed CAN (Controller Area Network) transceiver that provides a 2.5 kVrms isolated interface between a CAN protocol controller and the physical two-wire CAN bus, housed in a 16-pin SO (SOIC-16, 300 mil) package with capacitive (galvanic) isolation integrated on-chip. The device operates from a 3 V to 5.25 V supply on the logic/microcontroller side and supports a CAN data rate of up to 5 Mbps, making it suitable for Classic CAN and CAN FD frame formats. The integrated isolation removes the need for an external digital isolator + isolated DC-DC combination in many designs, reducing BOM count and PCB area. What is an isolated CAN transceiver? A CAN transceiver is the physical-layer bridge between a CAN controller (typically embedded in a microcontroller) and the differential CAN bus lines (CANH/CANL). A galvanically isolated version inserts a high-voltage barrier - here implemented via on-chip capacitive coupling - between the logic domain and the bus domain, breaking ground loops and protecting low-voltage MCU I/O from high-voltage transients common in automotive 12 V/24 V powertrain systems and industrial installations. Key features of the TJA1052IT/2Y include 1/1 unidirectional channel count, 2.5 kVrms isolation voltage rating, 5 Mbps maximum data rate, a standby mode for low quiescent current, and compatibility with 1.8 V and 3.3 V controller logic via separate VIO/VCC rails. The device is specifically targeted at Electric Vehicles (EV), Hybrid Electric Vehicles (HEV), and other automotive applications where high-speed CAN communication must coexist with high-voltage battery and inverter systems. Typical applications include EV/HEV battery management system (BMS) communication gateways, on-board chargers (OBC), traction inverter CAN interfaces, industrial CAN bus nodes requiring reinforced insulation, and isolated debug or service interfaces for automotive ECUs. When designing with the TJA1052IT/2Y, engineers should provide local decoupling on both the logic-side and bus-side supplies, observe creepage/clearance for the 2.5 kV isolation barrier, and verify the standby-mode behavior against the system power-state diagram. This page synthesizes distributor pricing, drop-in alternatives, and practical isolation-layout design notes not consolidated in the standalone manufacturer datasheet.

RFQ संपर्क
TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP
TJA1052IT/5

TJA1052IT/5 - Isolated 5 Mbps CAN Transceiver | NXP

The NXP TJA1052IT/5 is a galvanically isolated, high-speed CAN transceiver operating at up to 5 Mbps in a 16-lead SOIC package. It provides a 1-transceiver, 1-receiver CAN interface with a 3 V to 5.25 V supply range, matching the logic levels commonly used by CAN controllers, microcontrollers, industrial automation equipment, electric vehicles, and hybrid electric vehicles. A CAN transceiver is the physical-layer component that converts logic-level TXD and RXD signals into differential CAN bus signals, while receiving bus data and returning it as a logic-level RXD output. Galvanic isolation places a signal barrier between the CAN controller side and the two-wire CAN bus side. This helps protect the controller from ground-potential differences and electrical stress encountered in automotive and industrial installations. The TJA1052IT/5 supports CAN data rates up to 5 Mbps and operates from a 3 V to 5.25 V supply. NXP identifies the device as an active high-speed CAN transceiver, and distributor listings describe it as a 1-transceiver, 1-receiver isolated half-CAN interface in a 16-pin SOIC package. Its operating temperature and automotive-qualification details should be confirmed against the specific orderable part number and the manufacturer datasheet before production release. The part is especially relevant to electric and hybrid electric vehicle platforms, where a CAN controller must communicate with powertrain, battery-management, charger, and thermal-management subsystems. Industrial applications include motor drives, robotics, factory automation, and distributed control networks operating on long cable runs. Design layouts should follow the manufacturer’s recommended application circuit, including the prescribed bus termination, common-mode choke, and split capacitor network where applicable. Keep CANH and CANL routing symmetric and controlled, provide solid ground-plane continuity, and avoid placing sensitive analog or high-speed digital traces parallel to the differential bus. Confirm the isolation barrier treatment, maximum bus length, node count, and stub geometry for the target network. This page consolidates verified NXP product information, package and speed details, drop-in replacement candidates, comparison parameters, and practical CAN layout guidance to support component selection and PCB implementation.

RFQ संपर्क
TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP
TJA1053T/N1

TJA1053T/N1 - 5V Automotive CAN Transceiver | NXP

The NXP TJA1053T/N1 is a half CANbus transceiver for Controller Area Network communication, designed for a 4.75 V to 5.25 V supply range in a 14-pin SO package. Its interface pins tolerate voltages up to 36 V, supporting its use in automotive electrical environments when the surrounding circuitry provides the required protection and signal compatibility. The device combines a CAN transmitter and CAN receiver in one interface IC, providing the physical-layer connection between a CAN controller and the differential CAN bus. A CAN transceiver is an interface IC within the broader Controller Area Network hierarchy. It converts logic-level data into a differential bus signal at the transmitter and reconstructs a logic-level signal from the bus at the receiver. This physical-layer function allows a microcontroller, automotive control unit, or industrial controller to exchange reliable data over a multi-node CAN network without implementing the electrical interface directly. The TJA1053T/N1 operates from a nominal 5 V supply, with the documented operating range extending from 4.75 V to 5.25 V. Its I/O pins are tolerant to voltages as high as 36 V, an important consideration for 12 V automotive systems. The 14-SO package provides a compact surface-mount footprint suitable for automotive and industrial control equipment where PCB area is limited. The principal design benefit is the combination of a 5 V transceiver interface with high-side I/O tolerance. Logic-side circuitry can operate from the regulated 5 V rail, while the CAN interface remains capable of withstanding the voltage excursions commonly encountered in vehicle electrical systems. The tolerance rating does not remove the need for correct transceiver placement, bus termination, decoupling, and protection strategy. Typical uses include automotive body and comfort modules, engine controllers, instrument clusters, industrial automation equipment, CAN gateways, and embedded control systems. The device is particularly appropriate when the controller uses a 5 V supply and the CAN bus interface must tolerate the electrical environment associated with automotive wiring harnesses. When laying out a board, place the transceiver close to the CAN connector and route TXD and RXD as short traces away from high-current switching nodes. Terminate the bus at both physical ends with the resistance specified by the CAN network design. Follow the pin-description table and application guidance in the manufacturer datasheet before assigning PCB tracks, supply bypass capacitors, or bus protection components. This page consolidates the available manufacturer and distributor information with practical design guidance, package details, sourcing answers, and documented compatibility information. It helps engineers identify the correct CAN transceiver without confusing high-side I/O tolerance with immunity to arbitrary bus faults or eliminating the external protection required in automotive wiring.

RFQ संपर्क
TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP
TJA1054AT

TJA1054AT - Fault-Tolerant 125 kBd CAN Transceiver | NXP

NXP Semiconductors TJA1054AT is a fault-tolerant Controller Area Network transceiver intended for low-speed, single-wire CAN communication up to 125 kBd, supplied in a 14-pin SOIC package. The device sits between a CAN protocol controller and the physical bus wiring, providing the interface required to transmit and receive CAN signals while adding protection against faults on the bus. A CAN transceiver is the physical-layer component between a digital CAN controller and its bus wiring. The controller processes frames and protocol functions, while the transceiver converts logical controller signals into electrical bus signals and presents received bus information to the controller. A single-wire CAN interface uses one signal line for communication and normally requires a return path through the vehicle or equipment ground structure. The TJA1054AT is therefore positioned within the hierarchy of CAN interface IC, network interface, communications semiconductor, and integrated circuit. The TJA1054AT provides operation up to 125 kBd and is identified as a fault-tolerant CAN transceiver. The TJA1054A family is an electrostatic-discharge-improved version of the original TJA1054. NXP states that the TJA1054AT is pin and downward compatible with the PCA82C252T and TJA1053T, allowing those devices to be replaced while retaining their functions. Its SO14 package is a surface-mount package suitable for conventional automotive and industrial controller-board layouts. The principal design benefit is fault tolerance in environments where a CAN conductor may be exposed to wiring faults. Its 125 kBd maximum intended data rate supports low-speed CAN networks in passenger-car systems and other cost-sensitive embedded networks. A design must still observe the transceiver's detailed operating limits, bus topology, termination strategy, supply requirements, and external protection requirements defined by the manufacturer datasheet. Typical uses include body and comfort-control modules, passenger-car diagnostic equipment, low-speed automotive gateways, industrial control panels, and embedded CAN controllers. The device is most appropriate where a single-wire bus and fault-resilient physical interface are required. It should not be confused with differential two-wire CAN transceivers, which use separate CANH and CANL conductors. For PCB implementation, use the exact pin numbering and pin descriptions in the NXP data sheet, place the transceiver close to the connector or bus routing, and keep the CAN trace away from high-current switching paths. Confirm bus polarity, ground reference, decoupling, and any required external components during schematic review. This page adds lifecycle context, documented replacement relationships, package-level comparison, and practical design guidance around the TJA1054AT. Because NXP identifies the part as end of life, engineers should validate supply continuity, approved lifecycle status, and a complete sourcing plan before committing a new production design to this device.

RFQ संपर्क
TJA1054AT/M - 125 kBd Single-Wire CAN Transceiver | NXP
TJA1054AT/M

TJA1054AT/M - 125 kBd Single-Wire CAN Transceiver | NXP

NXP Semiconductors TJA1054AT/M is a fault-tolerant, ESD-improved single-wire CAN bus transceiver designed for low-speed automotive communication up to 125 kBd. It operates from a nominal 5 V supply and is packaged in a 14-pin SOIC-style gull-wing package identified by the TJA1054AT/M,518 ordering code. The device interfaces a CAN protocol controller with one physical bus conductor and provides the physical-layer functions required for reliable low-speed CAN communication. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the bus wiring. The TJA1054AT family belongs to the hierarchy of CAN interface ICs, communication transceivers, interface ICs, and semiconductors. Its single-wire architecture is intended for passenger-car systems operating at or below 125 kBd, where fault-tolerant behavior and ESD protection are important in electrically harsh vehicle environments. The TJA1054AT is an ESD-improved version of the original TJA1054. According to the NXP TJA1054A data sheet, the principal improvements concern electrostatic-discharge robustness while retaining the operating functions of the earlier device. NXP also identifies the TJA1054AT as pin and downwards compatible with the PCA82C252T and TJA1053T, allowing those components to be replaced while retaining their existing functions. The TJA1054T is a closely related member of the same device family. NXP states that the TJA1054AT and TJA1054T are interchangeable on the same 14-pin footprint, with the relevant distinction being the AT version's improved ESD characteristics. This relationship makes the TJA1054AT/M particularly useful for maintaining an existing SO14 PCB while improving transient immunity without changing the mechanical land pattern. Typical uses include single-wire CAN body and comfort networks, vehicle sensor nodes, door modules, lighting controllers, seat controllers, climate-control interfaces, and other low-speed automotive electronics. The transceiver's fault-tolerant design helps maintain communication when the bus has a short to ground or battery, provided the system remains within the device's specified electrical limits and uses the recommended bus protection and termination arrangements. PCB design should preserve the manufacturer's recommended decoupling and bus-network topology. Place the supply capacitor close to VCC and GND, route CAN wiring as a physically robust network, and apply protection appropriate to the vehicle harness. Because a CAN transceiver communicates through physical-layer signaling rather than a data protocol, the associated controller must support the matching single-wire CAN signaling convention. This page combines the NXP product description and family data with practical replacement guidance, package compatibility information, and application-oriented design considerations. It helps engineers distinguish a true same-footprint substitute from a merely similar CAN transceiver before committing an existing 14-pin automotive design to a new BOM.

RFQ संपर्क
TJA1054AT/N - Fault-Tolerant Low-Speed CAN Transceiver | NXP
TJA1054AT/N

TJA1054AT/N - Fault-Tolerant Low-Speed CAN Transceiver | NXP

The NXP Semiconductors TJA1054AT/N is a fault-tolerant Controller Area Network transceiver designed for low-speed CAN communication up to 125 kBd, particularly in passenger-car networks. It is an interface between a CAN protocol controller and the physical CAN bus conductors, and it is housed in a 14-pin SO package. The TJA1054A family is an electrostatic-discharge-improved implementation of the TJA1054. A CAN transceiver is an interface IC that connects a digital CAN controller to a physical bus. Unlike ordinary two-wire differential CAN, the fault-tolerant architecture used by the TJA1054A is intended for low-speed in-vehicle networks and adds local wake-up and bus-fault handling functions. Within the product hierarchy, the TJA1054AT/N is a CAN transceiver, an interface IC, and a semiconductor designed for automotive communication networks. The main feature of the TJA1054AT/N is its ability to replace the PCA82C252T and TJA1053T while retaining their functions because it is pin and downwards compatible with those devices. The TJA1054AT is likewise compatible with the TJA1054T. Its fault-tolerant CAN interface is intended for data rates up to 125 kBd, while the ESD-improved TJA1054A design strengthens its suitability for electrically demanding vehicle networks. The device also provides local wake-up support through the WAKE pin. According to the NXP TJA1054 documentation, a local wake-up request is detected through an edge followed by a qualifying level exceeding the specified wake-up interval. The transceiver can then assert its INH output high to activate an external supply regulator. This feature is useful in distributed vehicle systems where a node must awaken a local subsystem without waking the entire network. Typical applications include passenger-car low-speed CAN networks, body and comfort systems, door modules, seat controllers, lighting controllers, climate-control interfaces, and other automotive ECUs connected by low-speed CAN. The TJA1054AT/N is most appropriate when the system specifically requires a fault-tolerant single-wire CAN physical layer and does not require the high-speed differential CAN architecture used by many newer vehicle platforms. When designing a replacement around this device, verify the physical footprint, exposed functionality, and bus topology. Although the NXP product information identifies compatibility with the PCA82C252T and TJA1053T, a replacement should still be checked for system-level differences in wake-up behavior, supply operation, bus termination, and application timing. Use the manufacturer's pin-description table when assigning PCB nets and the recommended application circuit when selecting external components. This page combines the confirmed NXP product information, manufacturer datasheet links, package details, compatibility statements, and application guidance. It also organizes practical design considerations and direct replacement questions so engineers can assess the TJA1054AT/N against its documented drop-in-compatible predecessors without confusing low-speed fault-tolerant CAN with high-speed differential CAN.

RFQ संपर्क
TJA1054AT/VM - 125 kBd CAN Transceiver | NXP Automotive
TJA1054AT/VM

TJA1054AT/VM - 125 kBd CAN Transceiver | NXP Automotive

NXP TJA1054AT/VM is a fault-tolerant CAN transceiver for low-speed Controller Area Network communication up to 125 kBd, presented in a 14-pin SO package. The device provides the physical interface between a CAN protocol controller and the CAN bus wiring while adding ESD protection to the original TJA1054 function. It is primarily intended for passenger-car systems where low-speed CAN networks connect electronic control units and body electronics. A CAN transceiver is an interface IC within the broader hierarchy of communication interfaces, network semiconductors, and integrated circuits. It converts logic-level signals from a CAN controller into physical bus levels and receives bus signals for presentation to the controller. The TJA1054AT/VM supports legacy CAN systems operating at or below 125 kBd, including applications where bus-node fault tolerance is important. NXP identifies the TJA1054AT as pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T while retaining all functions. The TJA1054T provides a closely related device in the same product family. This compatibility enables design updates or repair substitutions without changing the PCB land pattern, provided that supply voltage, transceiver mode, bus termination, and software configuration requirements are checked against the detailed NXP documentation. The fault-tolerant architecture is the central technical feature of the TJA1054 family. Compared with ordinary CAN transceivers, fault-tolerant implementations add behavior intended to continue communication when one bus line is shorted to ground, shorted to the supply, or disconnected. Exact fault-detection limits, recovery behavior, and loopback behavior must be confirmed from the NXP TJA1054 datasheet before setting system test expectations. Typical uses include passenger-car body-control modules, low-speed CAN gateways, electronic control units, vehicle comfort systems, diagnostic interfaces, and industrial equipment that retains an automotive CAN network. A 125 kBd data rate is appropriate for low-bandwidth control and status traffic rather than high-speed vehicle backbone or payload-oriented industrial CAN networks. PCB implementation should preserve short, symmetric CANH and CANL routes, a common ground reference, correct 120-ohm bus termination at each physical network end, and protection suitable for the vehicle environment. Because TJA1054AT/VM is the ESD-improved member of the TJA1054 family, designers should still apply appropriate external bus protection where the installation exposes connectors to severe transients. This product page combines the NXP compatibility statement, package identification, CAN data-rate information, verified replacement candidates, and practical PCB guidance. It also separates confirmed electrical details from parameters that require consultation of the manufacturer datasheet, helping engineers make a defensible sourcing and design decision without relying on unsupported assumptions.

RFQ संपर्क
TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP
TJA1054T/N1

TJA1054T/N1 - Fault-Tolerant 125 kBd CAN | NXP

The NXP Semiconductors TJA1054T/N1 is a fault-tolerant Controller Area Network transceiver designed for low-speed CAN communication up to 125 kBd in passenger-car applications. It provides the physical-layer interface between a CAN protocol controller and the CANH and CANL bus conductors, and the device is packaged in an 14-pin small-outline SOIC package. Its fault-tolerant architecture is intended for communication links where reliable operation during bus faults is important. A CAN transceiver is an interface IC within the wider network-interface and semiconductor hierarchy. It converts logic-level transmit and receive signals from a CAN controller into the physical differential signaling used on a CAN bus. CAN itself is a deterministic, multiplexed communication network used in automotive and industrial control systems. The TJA1054T/N1 occupies the physical-layer position between digital processing circuitry and the two-wire bus. The TJA1054T/N1 is identified as a fault-tolerant CAN transceiver and is primarily intended for low-speed networks operating at up to 125 kBd. NXP states that the device is pin-compatible and downwards-compatible with the PCA82C252T and TJA1053T, allowing either device to be replaced while retaining the existing functions. This compatibility makes the TJA1054T a practical upgrade path for designs already using those interface devices. The principal engineering benefit is bus-fault tolerance. NXP describes very low electromagnetic emission as an important improvement over the PCA82C252 and TJA1053T, based on strong matching between the CANH and CANL outputs. Good matching helps limit differential-mode emissions and improves signal quality on the physical bus. The TJA1054 family also retains the functional structure expected by existing CAN controllers, allowing a PCB-level replacement without changing the surrounding bus interface. Typical uses include passenger-car body and comfort networks, low-speed automotive CAN subnets, sensor and actuator gateways, and industrial equipment that retains an automotive CAN architecture. In these systems, the transceiver connects a CAN controller to CANH and CANL, provides bus-side transmit and receive functions, and helps the network continue operating correctly when the bus is shorted to ground, shorted to supply, or open. Exact protection and operating details should be confirmed in the manufacturer datasheet. PCB implementation should preserve the device's pin compatibility with the PCA82C252T and TJA1053T, including the same 14-pin SOIC footprint and signal assignments. Check the bus-polarity, supply, ground, transceiver-mode, and controller-interface connections against the NXP pin description before fabrication. Do not assume that all CAN transceivers are interchangeable merely because they use the same protocol; interface voltage, mode-control logic, and fault behavior must also match. This product page combines the manufacturer compatibility information, package identification, available ordering references, and practical replacement guidance in one engineering-focused record. It also distinguishes verified drop-in choices from options that require package or function review, helping engineers evaluate a CAN bus update without relying on an incomplete cross-reference list.

RFQ संपर्क
TJA1054T/N1M - 125 kBd Fault-Tolerant CAN Transceiver | NXP
TJA1054T/N1M

TJA1054T/N1M - 125 kBd Fault-Tolerant CAN Transceiver | NXP

The NXP Semiconductors TJA1054T/N1M is a fault-tolerant Controller Area Network transceiver intended for low-speed CAN communication systems operating up to 125 kBd. The device interfaces a CAN protocol controller with the physical CAN bus and is supplied in a 14-pin SOIC package for surface-mount assembly. Its fault-tolerant architecture supports communication in automotive and industrial environments where bus faults and wiring conditions require greater robustness than a conventional CAN transceiver. A CAN transceiver is an interface IC that converts logic-level signals between a host CAN controller and the differential CANH and CANL bus conductors. The TJA1054T/N1M belongs to the broader hierarchy of CAN interface ICs, network interface semiconductors, and connectivity semiconductors. Its bus-side interface handles dominant and recessive states, while the logic-side interface connects with the protocol controller through transmit, receive, enable, and related control signals. According to the NXP TJA1054 data sheet, the TJA1054T is pin and downwards compatible with the PCA82C252T and TJA1053T. This compatibility supports replacement of those devices with the TJA1054T while retaining all functions. The improvement identified by NXP includes very low electromagnetic emission because of good matching between the CANL and CANH outputs. The fault-tolerant design also supports local wake-up detection through the WAKE pin and can assert the INH output to activate an external supply regulator. The TJA1054T is primarily intended for low-speed applications up to 125 kBd in passenger vehicles and comparable embedded CAN networks. Typical uses include body-control modules, automotive comfort systems, door modules, seat controllers, lighting controllers, sensor interfaces, industrial automation equipment, and low-speed vehicle networks. Its interface role isolates the protocol controller from the physical bus while providing bus-side drive, receive, fault tolerance, and wake-up support. When placing the device in a design, follow the manufacturer data sheet for the exact pin assignments, termination configuration, supply decoupling, bus polarity handling, and exposed fault conditions. The CANH and CANL traces should be routed as a differential pair, with the bus termination kept physically close to the connected nodes. The 14-pin SOIC footprint permits conventional PCB assembly, but the circuit must still be reviewed against the NXP application guidance for EMC performance and fault recovery. This page combines the TJA1054T family identity, package information, compatibility information, replacement candidates, and practical selection considerations for engineers evaluating the TJA1054T/N1M. It distinguishes the base device from the N1M ordering suffix and directs detailed engineering decisions to the manufacturer data sheet, where the complete electrical limits, timing characteristics, pin descriptions, and test conditions are defined.

RFQ संपर्क
TJA1055T - 125 kBd Fault-Tolerant CAN Transceiver | NXP | SOIC-14
TJA1055T

TJA1055T - 125 kBd Fault-Tolerant CAN Transceiver | NXP | SOIC-14

The NXP Semiconductors TJA1055T is an enhanced fault-tolerant CAN transceiver that interfaces a CAN protocol controller with the physical CANH and CANL bus wires, intended for low-speed in-vehicle communication up to 125 kBd in passenger cars, and it is supplied in a 14-pin SOIC (SOP-14) surface-mount package. A CAN transceiver is the physical-layer device in a Controller Area Network link. It sits between the CAN protocol controller inside a microcontroller and the differential bus wiring, converting controller logic levels into balanced bus-line signals and, in the opposite direction, converting received bus states into a clean logic-level receive output. In the classification hierarchy it is an interface IC, specifically a CAN interface or CAN bus transceiver, a member of the broader transceiver and interface IC family used in automotive and industrial communication networks. Key features of the TJA1055T include its enhanced fault-tolerant bus-line interface, its optimization for low-speed in-car communication, and its pin-to-pin compatibility with the earlier TJA1054 and TJA1054A devices, which allows an upgrade of an existing design without a board change. The fault-tolerant architecture is the defining improvement over the predecessor family, adding protection against faults that occur on the bus lines during operation. Technically, the device operates with the standard differential CAN signalling scheme in which the two bus lines are dominant and recessive states rather than fixed levels. Because the TJA1055T is specified for low-speed networks up to 125 kBd, it is intended for body, comfort and convenience sub-networks rather than for powertrain or chassis high-speed CAN links, where devices rated for 1 Mbit/s or more are normally chosen. The 14-pin SOIC package is a standard surface-mount footprint that simplifies assembly and rework in automotive electronics manufacturing. Typical applications include body control units, door and seat modules, climate control units, window and lighting controllers, passenger-comfort CAN sub-networks, vehicle diagnostic interfaces, low-speed CAN gateways for industrial and building systems, and CAN bus test and monitoring equipment. When laying out the design, place the transceiver close to the bus connector, keep the CANH and CANL traces short and matched, provide the required bus termination resistors at the physical ends of the segment, and decouple the supply pins close to the device to limit conducted noise on the bus. Confirm that the transceiver variant selected matches the supply and bus configuration of the target network before releasing the layout. This page consolidates the manufacturer description, verified distributor listings, drop-in replacement candidates and practical integration guidance for the TJA1055T in one place, so engineers can qualify the part and plan a sourcing strategy without searching through multiple listings and cross-reference tools.

RFQ संपर्क
TJA1055T/1J - 125 kBd Fault-Tolerant CAN Transceiver
TJA1055T/1J

TJA1055T/1J - 125 kBd Fault-Tolerant CAN Transceiver

NXP Semiconductors TJA1055T/1J is an enhanced fault-tolerant Controller Area Network transceiver for low-speed data links up to 125 kBd. It operates from a 4.75 V to 5.25 V supply and is packaged in a 14-pin SOIC for surface-mount assembly. The device connects a CAN protocol controller to the physical CANH and CANL bus conductors while providing differential transmit, receive, and fault-tolerance functions. A CAN transceiver is the physical-layer interface between a digital CAN controller and the wired CAN network. The TJA1055 family belongs to the interface-IC hierarchy and is specifically optimized for in-car low-speed communication, where its 125 kBd target complements higher-speed CAN controller and transceiver families. Its enhanced fault tolerance helps maintain operation when the bus is shorted to ground, shorted to the supply, or open-circuit, subject to the detailed protection and operating conditions stated by NXP. Key verified characteristics include a 125 kBd low-speed CAN application target, a 4.75 V minimum supply, a 5.25 V maximum supply, and a 14-pin SOIC package. NXP identifies the TJA1055 as pin-to-pin compatible with the TJA1054 and TJA1054A. Distributor listings also identify TJA1055T/1J as an automotive CAN interface available in tape-and-reel ordering. The transceiver should be placed near the CAN bus connector, with its CANH and CANL pins connected to the protected bus wiring and its TXD and RXD pins connected to the CAN controller. Because the device is intended for passenger-car and other low-speed CAN links, system designers should verify timing, termination, bus topology, logic levels, and protection requirements against the manufacturer datasheet before production release. The TJA1055T/1J is suitable for automotive body electronics, comfort modules, diagnostic equipment, sensor nodes, and other 125 kBd CAN applications. Its principal design consideration is that CAN bus behavior depends on termination, wiring, common-mode conditions, and transceiver protection. A CAN bus should not be treated as a generic communication line; the selected transceiver, controller, and network implementation must be validated together. This page combines verified manufacturer and distributor information, package and ordering details, and application guidance for engineers evaluating a SOIC-14 CAN physical-layer interface.

RFQ संपर्क
TJA1055T/2Z - 125 kBd Fault-Tolerant CAN Transceiver | NXP
TJA1055T/2Z

TJA1055T/2Z - 125 kBd Fault-Tolerant CAN Transceiver | NXP

The NXP Semiconductors TJA1055T/2Z is an enhanced fault-tolerant Controller Area Network transceiver intended for low-speed automotive applications up to 125 kBd. It provides a physical-layer interface between a CAN protocol controller and the CAN bus conductors, uses a 14-SO package, and is supplied in tape-and-reel packaging. According to the NXP product information, its budgetary price is $1.15 USD at a quantity of 1,000 and its indicated lead time is 10 weeks. A CAN transceiver is an interface IC that connects a host controller to a differential CAN network. It belongs to the communication interface hierarchy: CAN transceiver > bus transceiver > interface IC > semiconductor. Unlike a generic transceiver, this device is designed around the electrical behavior and fault tolerance requirements of low-speed CAN systems, where dependable operation during wiring faults and disturbed bus conditions is important. Key documented features include enhanced fault-tolerant CAN operation, support for data rates up to 125 kBd, and use in passenger-car CAN networks. The verified distributor records also identify the device as a one-channel, half CAN-bus transceiver in a 14-SO package. The NXP product page identifies TJA1055T as active and lists reel-reel packing with a minimum package quantity and minimum order quantity of 2,500 pieces. The TJA1055T/2Z performs the physical signaling required between the CAN controller and the bus while providing the fault-tolerance behavior expected in automotive environments. Its use of a dedicated bus interface allows the controller to send and receive frames without implementing analog bus-level signaling directly. Detailed thresholds, loopback behavior, supply current, and absolute maximum ratings remain [DATA_NEEDED: complete electrical characteristics] because they were not included in the supplied verified records. Typical uses include passenger-car body and comfort systems, door modules, climate-control controllers, lighting controllers, instrument clusters, and other low-speed CAN nodes. It is most appropriate where the network operates at 125 kBd or below and the design requires a dedicated high-reliability CAN physical-layer device rather than a general-purpose differential transceiver. When designing a PCB around the TJA1055T/2Z, verify the complete NXP datasheet pinout, transceiver termination requirements, supply decoupling, and bus-fault behavior before layout release. The supplied search records establish the 14-SO package designation but do not expose a verifiable numbered pin table, so this page does not infer pin names or connectivity. Maintain the manufacturer-specified CAN bus topology and provide the required local decoupling and protection appropriate to the vehicle network.

RFQ संपर्क
TJA1055T/3/1J - 125 kBd Fault-Tolerant CAN Transceiver | NXP
TJA1055T/3/1J

TJA1055T/3/1J - 125 kBd Fault-Tolerant CAN Transceiver | NXP

NXP Semiconductors TJA1055T/3/1J is an enhanced fault-tolerant Controller Area Network transceiver with differential transmit and receive capability, optimized for low-speed CAN communication up to 125 kBd. The device operates from a 5 V to 28 V supply range, includes a 3 V VIO variant for interfacing with low-voltage CAN controllers, and is offered in a 14-pin SO surface-mount tape-and-reel package. It is designed for passenger-car body and comfort electronics where fault tolerance and low-speed in-vehicle networking are important. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the differential CAN bus. It converts controller logic signals into CANH and CANL bus activity and converts differential bus voltage into a receive signal. Positioned within the hierarchy of CAN interface ICs, transceiver ICs, interface ICs, and semiconductors, the TJA1055T provides the electrical interface required to connect digital controllers to a robust in-vehicle communication network. The TJA1055T/3/1J provides operation at data rates up to 125 kBd, differential receive and transmit functions, and sleep or standby operating modes for reduced power consumption. Its supply-voltage coverage supports systems operating from 5 V, 9 V, 12 V, 15 V, 18 V, 24 V, and 28 V environments. The /3 order-code variant provides a 3 V VIO interface, allowing compatibility with controllers or logic domains using a lower supply voltage. The device uses differential bus signaling to provide common-mode rejection and improve robustness against noise found in vehicle electrical environments. Its fault-tolerant design is intended for low-speed CAN networks in passenger cars rather than high-bandwidth automotive Ethernet or high-speed CAN FD systems. The 14-pin SO package supports compact surface-mount assembly while exposing the controller interface, bus interface, power, ground, and control connections required by the device architecture. Typical applications include vehicle body-control modules, door and seat controllers, climate-control interfaces, lighting controllers, comfort systems, and distributed low-speed passenger-car networks. The combination of a 125 kBd maximum data rate, broad supply range, sleep or standby support, and 3 V VIO option makes the TJA1055T/3/1J appropriate where a 3.3 V controller must communicate with a conventional 12 V or 24 V vehicle CAN network. When designing the PCB layout, treat CANH and CANL as a controlled-impedance differential pair routed as symmetrically as practical, with a continuous return path beneath the pair. Keep the transceiver close to the bus connector or bus-header, minimize stub branches, and follow the grounding and decoupling recommendations in the manufacturer datasheet. Component values and layout distances not present in the supplied source extract remain unverified and must be confirmed from the complete NXP datasheet before release. This page consolidates the verified NXP product information, distributor listings, order-code distinctions, and package data for TJA1055T/3/1J. It also distinguishes confirmed drop-in references from unsupported cross-brand equivalents, highlights verified design parameters, and clearly identifies pricing, pin-mapping, and detailed electrical values that still require confirmation.

RFQ संपर्क
TJA1055T/3/2Z - 125 kbit/s Fault-Tolerant CAN Transceiver | NXP | SO-14
TJA1055T/3/2Z

TJA1055T/3/2Z - 125 kbit/s Fault-Tolerant CAN Transceiver | NXP | SO-14

The NXP Semiconductors TJA1055T/3/2Z is an enhanced fault-tolerant CAN transceiver for low-speed Controller Area Network buses up to 125 kbit/s, packaged in a 14-pin SO (SOIC-14) surface-mount package with an exposed ground-pad-style land pattern. It accepts supply rails of 5 V, 9 V, 12 V, 15 V, 18 V, 24 V and 28 V, and provides a single differential transmit and receive channel (1/1, half duplex) with sleep and standby modes for low-current parked vehicles. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the two-wire differential bus. It converts the controller's logic-level TXD and RXD signals into balanced bus levels, and returns a filtered digital receive signal. The TJA1055 belongs to the fault-tolerant CAN transceiver family, where the bus driver survives shorted-bus and reversed-battery conditions that would damage a conventional high-speed transceiver. Key characteristics include operation up to 125 kbit/s, an enhanced fault-tolerant transmit driver, a receive filter with extended glitch rejection, low-current sleep and standby operating modes, and AEC-Q100 qualification for automotive applications. The device is pin-to-pin compatible with the earlier TJA1054 and TJA1054A, which allows existing low-speed CAN body, comfort and diagnostic modules to be updated without a layout change. Internally the device separates the controller interface from the bus interface so that the bus-side driver can withstand faults independently of the logic side. A dedicated sleep input and internal mode control let a body control module wake the transceiver only when needed, reducing standing current in parked vehicles. The recessive and dominant output levels are defined to suit ISO 11898-2 style low-speed CAN networks. Typical uses include passenger-car door modules, seat and window controllers, climate control panels, body control units, diagnostic connectors, trailer modules and other 125 kbit/s CAN nodes in vehicles, plus industrial equipment that adopts low-speed CAN for cable-cost reduction. When laying out the board, place the bus transceiver close to the connector and keep the CANH and CANL traces short, matched in length and free of stubs, because the twisted pair carries a differential signal whose balance determines noise immunity. The logic-side pins need short traces to the CAN controller and a solid ground reference, since the transceiver converts bus common-mode voltage into a single-ended logic output. This page consolidates manufacturer ratings, package details, drop-in alternatives, application guidance and layout notes so that engineers can evaluate the TJA1055T/3/2Z for a low-speed CAN node without rebuilding the data from multiple sources.

RFQ संपर्क
TJA1055T/3/C - 125 kBd Fault-Tolerant CAN Transceiver | NXP
TJA1055T/3/C

TJA1055T/3/C - 125 kBd Fault-Tolerant CAN Transceiver | NXP

The NXP Semiconductors TJA1055T/3/C is an enhanced fault-tolerant Controller Area Network transceiver designed for low-speed passenger-car networks operating up to 125 kBd. It provides differential CAN transmit and receive functions and is intended to interface a CAN protocol controller with the physical CANH and CANL bus wires. The device is offered in a 14-pin SO package for surface-mount PCB assembly. A CAN transceiver is the physical-layer interface between a digital protocol controller and a differential CAN bus. It converts controller logic levels into balanced bus signals and reconstructs a valid receive signal from the bus. Within the broader hierarchy, the TJA1055T/3/C is a CAN transceiver, a bus interface IC, an interface circuit, and a semiconductor. Its fault-tolerant design is intended to maintain communication when bus faults or unusual bus conditions occur, making it suitable for automotive body, comfort, and other low-speed distributed systems. The principal documented characteristics include an enhanced fault-tolerant CAN architecture, differential transmission and reception, and operation to 125 kBd. The /3 ordering option is documented in the TJA1055 family as a version with a current source connected to ground for the RTH and RTL pins. Fault-tolerant operation also depends on correctly implementing the resistor network and recessive-state biasing around the transceiver. NXP describes the TJA1055 family as an interface between the CAN protocol controller and physical bus wires in passenger cars. Its architecture supports low-speed CAN communication while adding fault-tolerance improvements relative to earlier transceivers. The /3 variant provides defined current-source behavior for the RTH and RTL pins, which is important when reproducing the reference termination and bias circuit on an existing PCB. Typical uses include passenger-car body-control modules, door and window controllers, seat and climate-control electronics, lighting controllers, instrument-cluster peripherals, and other low-speed CAN nodes. Automotive qualification details, exact transceiver timing limits, and the full electrical limits must be checked against the complete NXP data sheet before a new production design is released. Designers should preserve the established SO-14 footprint and pin assignments when qualifying this device. The termination-bias network, CANH and CANL routing, ground return, and protection components should follow the manufacturer application circuit. Because bus-node behavior depends on both the transceiver and external resistors, changing one network component without checking the complete termination scheme can alter dominant and recessive levels. This product record combines the verified NXP family description, available ordering-code information, package identification, fault-tolerance characteristics, and practical replacement considerations. It also identifies where complete electrical, environmental, qualification, lifecycle, and pin-function details must be taken directly from the NXP documentation or confirmed with the manufacturer before production release.

RFQ संपर्क
TJA1055T/3/CM - 125 kBd Fault-Tolerant CAN | NXP
TJA1055T/3/CM

TJA1055T/3/CM - 125 kBd Fault-Tolerant CAN | NXP

The NXP TJA1055T/3/CM is an enhanced fault-tolerant CAN transceiver supporting data rates up to 125 kBd in a 14-pin SOIC package. It operates from a 5 V to 28 V supply range, supports 9 V, 12 V, 15 V, 18 V, and 24 V battery configurations, and provides sleep and standby operating modes for reduced system power. The device is supplied in tape-and-reel packaging and is identified as an automotive AEC-Q100 transceiver. A CAN transceiver is the physical-layer interface between a CAN protocol controller and the differential CAN bus. The TJA1055T/3 family combines transmit and receive functions, bus-fault detection, and fault-tolerant behavior in one interface IC. This hierarchy connects the device to CAN controllers, vehicle networking systems, industrial communication equipment, and embedded electronic control units. Key features include differential receive and transmit capability, fault-tolerant operation, a maximum bus speed of 125 kBd, and low-power sleep and standby modes. The 5 V to 28 V supply range accommodates conventional automotive battery systems, while the AEC-Q100 designation identifies suitability for automotive qualification requirements. Its 14-pin SOIC format supports conventional surface-mount assembly and compact controller-area-network routing. The transceiver is intended for low-speed CAN communication and provides the electrical interface between digital controller logic and the physical bus. Differential signaling improves signal integrity and common-mode rejection on the CANH and CANL conductors. Fault-tolerant circuitry is intended to maintain communication when bus faults occur, although system behavior still depends on termination, wiring, grounding, and the selected network topology. Typical applications include passenger-car body and comfort electronics, automotive control modules, low-speed diagnostic equipment, industrial CAN controllers, and embedded systems that connect a CAN controller to a two-wire bus. The sleep and standby functions are particularly useful where modules must reduce current consumption while retaining controlled bus connectivity. Place the transceiver close to the bus connector and CAN controller, route CANH and CANL as a tightly coupled differential pair, and provide the termination required by the network. Keep the ground reference and power-return routing consistent with the bus structure to minimize common-mode effects. Confirm device pin assignments in the NXP datasheet before assigning connector, controller, and supply connections. This product page combines the TJA1055T/3/CM technical identity with verified package, speed, supply, mode, and automotive information. It also provides application guidance, drop-in comparison candidates, and practical PCB considerations to support faster component selection and implementation.

RFQ संपर्क